SPECIFICATIONS

RX16JFT & RX16FT-PSFlush Mount Lift Rack

Site SpecificationsSubstructure Requirements Refer to 6339-T for full detailsPower Requirements 208-230 VAC, single phase power, 26 Amp

Air Supply Requirements 90-150 PSI (6.2-10.3 bar)Jacks require 125 PSI (8.6 bar) for full capacity

Minimum Concrete Spec. 3 in. (76 mm) thick, 3000 PSI (20,700kPA) ratingMaximum Floor Slope 2 in. (51 mm) over 126 in. (3200 mm)

Product SpecificationsMax. Vehicle Weight 16,000 lbs. (7257 kg)

Max. Wheelbase General Service 187 in. (4750 mm) Two-Wheel Alignment 182 in.(4623 mm) Four-Wheel Alignment 158 in. (4013 mm)Alignment Height All lock positionsMin. Four-Wheel Alignment 88 in. (2235 mm)Lifting Speed 1 speed, 60 secondsLowering Speed 2 speed, 25 seconds

RX16FT-PS Shown

Form 6491-T, 06-15 Supersedes Form 6491-T, 08-13a

Copyright © 2015, Hunter Engineering Company

For lift rack information visit:www.hunter.com/lift-racks

For local contact visit:www.hunter.com/contact-hunter

For general inquiries visit:www.hunter.com

or call800-448-6848

MODEL FEATURES / DIMENSIONS

Features JFT FT-PS

9000-lb Swing Air Jacks (2)

Two-Speed Lowering

Dimension

Outside Width (W1) 92.5 in.2350 mm

Inside Width (W2) 40 in.1016 mm

Length (L) 231.375 in.5877 mm

Runway Width (R) 26 in.660 mm

Raised Height (H1) 72 in.1829 mm

Depth (H2) 14.75 to 15.25 in.375 to 387 mm

Continued on Page 2

W1

H1

H2

L

W2 R

SPECIFICATIONS (Refer to 6339-T for substructure construction requirements)

RX16JFT & RX16FT-PSFlush Mount Lift Rack

Form 6491-T, 06-15Supersedes Form 6491-T, 08-13a

Copyright © 2015, Hunter Engineering Company

*Non-standard positioning of control console is limited to a maximum space between console and rack of 6 feet (1829 mm) at the approach ramp end and 17 feet (5182 mm) at the turnplate end. Additional threshold and perhaps hydraulic hoses will be required (refer to Installation Instruction for details).

All dimensions shown are for finished pit. Accomodate tile thickness as needed.

! WARNING

!WARNING

!WARNING

!WARNING

DRAINLOCATED

INCENTEROF PIT

SLOPEPIT

FLOORTOWARD

DRAIN(1/2")

CONSOLE CONDUIT DETAIL

96 1/2"(2451 mm)

OPTIONAL CONSOLELOCATION

16"(406mm)

22"(559 mm)

6" MIN.*152 mm( )

OPTIONAL 1 1/2 IN. DIA. CONDUITFOR COMMUNICATION CABLE

TO ALIGNMENT CONSOLE

HAWKEYE SERIES SENSORSAND PRONTO SYSTEMS HAVE

SPACE REQUIREMENTS INFRONT OF LIFT THAT MUST BEMET, REFER TO APPROPRIATE

SITE REQUIREMENTS.

ENTIRE PIT(BOTTOM AND WALLS)

MUST BE HARDTROWEL FINISH

34 3/4"(883 mm) EXTENDER

PLATES51-2464-1-PPP

ANDRAMPS

147-141-1-PPP 231 3/8"(5877 mm)

64"(1626 mm)

33 3/4"(857 mm)

! WARNINGSTAY BEHINDYELLOW LINE

WHEN THELIFT MOVES.

128-978-2

DECAL 128-978-2

PLACED ON EACHPERIMETER ANGLE

(4 PLACES)AND EACH SIDE OF

LIFT (2 PLACES)

!W

AR

NIN

G

APPROX. 2"(51 mm)TYPICAL

ANGLE AROUND PITPERIMETER

PAINTED SAFETYYELLOW

(NOT SUPPLIED BYHUNTER)

32"(813 mm)

RAMPS147-141-1-PPP

OPTIONAL REAR STEP(6" (152 mm) MAX. HT.)

PIT DEPTH OF14 3/4" to 15 1/4"

(375 mm to 387 mm)REQUIRED AT

FRONT END OF PIT

OPT. FRONT STEP(12" (305 mm)MAX. DEPTH)

45

6" MIN.RADIUS CONDUIT

EXIT FLUSHWITH

PIT FLOOR

ROUTE 4" MIN DIAMETERCONDUIT OR EQUIVALENTCLOSED CHANNEL FROMPIT FLOOR TO BASE OF

CONSOLE

* LONGER VEHICLES WILL NEED TO BE SERVICED WITH BAY DOOR OPEN. TOACCOMMODATE MOST VEHICLES, INCREASE SPACE BEHIND PIT TO ( ) ORGREATER.

39" 991 mm** SITES WITH D.R.W. TRUCKTRAFFIC SHOULD USE 20" MIN.CONSOLE TO PIT DISTANCE.

**15" TO 41"

(381 TO 1041 mm)

VEHICLE APPROACH

BAY DOORBAY DOOR