run dry slurry seal heavy duty submersible slurry pumps...
TRANSCRIPT
Heavy Duty Submersible Slurry Pumps For Industrial Applications
STANDARD HDS FEATURES
Run Dry Slurry Seal
Mechanical seal configuration designed for prolonged motor operation in severe duty slurry applications
Double mechanical seals operate in an oil chamber where components are isolated from the pumped slurry
Carbon-Ni Resist face (upper) & Tungsten Carbide face (lower) w/ stainless hardware
Particle Ejection Ports
Expels solids to extend seal life
Maintains minimum flow during closed valve operation
HDS Agitator
Solids are propelled into suspension by the mixing
action of the blades
Heavy Duty XP Seal
Carbon-Ni Resist faces & 316 Stainless Steel hardware for internal seal
Tungsten Carbide faces & 316 StainlessSteel hardware for external seal
Seal Leak Detector
Senses moisture if the external seal fails and sends a signal to the control panel
Water Jacket
Provides motor cooling for run dry & hot sump applications
www.keystonepumps.com
Control Panel
Simplex / Duplex
Ground Fault & Ground Check Monitoring
Custom Designs Available
Jet Ring
Settled solids are induced into suspension
by the water jetting action of the nozzles
Lifting Bail
Allows for a central lift point / Low temperature operation design
OPTIONAL HDS FEATURES
Unit 307 – 2999 Underhill AveBurnaby, B.C. V5A 3C2
Toll-free: 1.888.875.3323Phone: 604.227.3555
Fax: 604.229.0494Email: [email protected]
www.keystonepumps.com2013 Keystone Pumps, All rights reserved
C
M
Y
CM
MY
CY
CMY
K
Keystone_Brochure_PRINT.pdf 1 13-07-31 10:52 AM
Keystone HDS Low-Head Hydraulic Performance
Discharge Size [in. (mm)] 2" (50)Impeller Diameter [in. (mm)] 8.46" (215)Min. Impeller Diameter [in. (mm)] 6.77" (172)Max Solid Size in. (mm) 0.63" (16)Motor Frame Size 180TY / 210TYSMotor Power HP 5 / 7.5 / 10 / 15 / 20Freq [(Hz) / RPM]¹ (60) / 1200 & 1800Voltage 230 / 460 / 575Insulation² F / H / High AmbientWeight³ [lbs. (kg)] 180 TY - 349 (159) / 210 TYS - 464 (211) Discharge Size [in. (mm)] 3" (75)Impeller Diameter [in. (mm)] 8.46" (215)Min. Impeller Diameter [in. (mm)] 6.77" (172)Max Solid Size in. (mm) 0.86" (22)Motor Frame Size 180TY / 210TYSMotor Power HP 5 / 7.5 / 10 / 15 / 20Freq [(Hz) / RPM]¹ (60) / 1200 & 1800Voltage 230 / 460 / 575Insulation² F / H / High AmbientWeight³ [lbs. (kg)] 180TY - 371 (168) / 210TYS - 484 (221) Discharge Size [in. (mm)] 4" (100)Impeller Diameter [in. (mm)] 9.05" (230)Min. Impeller Diameter [in. (mm)] 7.24" (184)Max Solid Size in. (mm) 1.26" (32)Motor Frame Size 180TY / 210TYSMotor Power HP 5 / 7.5 / 10 / 15 / 20Freq [(Hz) / RPM]¹ (60) / 1200 & 1800Voltage 230 / 460 / 575Insulation² F / H / High AmbientWeight³ [lbs. (kg)] 180TY - 403 (182) / 210TYS - 518 (235) Discharge Size [in. (mm)] 6" (150)Impeller Diameter [in. (mm)] 9.84" (250)Min. Impeller Diameter [in. (mm)] 7.82" (200)Max Solid Size in. (mm) 1.26" (32)Motor Frame Size 250TY / 320TYSMotor Power HP 25 / 30 / 40 / 50 / 60 / 75Freq [(Hz) / RPM]¹ (60) / 1200 & 1800Voltage 460 / 575Insulation² F / H / High AmbientWeight³ [lbs. (kg)] 250TY - 1058 (482) / 320TYS - 1461 (664) Discharge Size [in. (mm)] 8" (200)Impeller Diameter [in. (mm)] 14.76" (375)Min. Impeller Diameter [in. (mm)] 11.81" (300)Max Solid Size in. (mm) 1.58" (32)Motor Frame Size 320TY / 360TYS / L360TYSMotor Power HP 40 / 50 / 60 / 75 / 100 / 125 / 150 Freq [(Hz) / RPM]¹ (60) / 900 & 1200Voltage 460 / 575Insulation² F / H / High AmbientWeight³ [lbs. (kg)] 320TY - 2015 (916) / L360TYS - 2430 (1100) Discharge Size [in. (mm)] 10" (250)Impeller Diameter [in. (mm)] 20.47" (520)Min. Impeller Diameter [in. (mm)] 16.37" (416)Max Solid Size in. (mm) 2.2" (56)Motor Frame Size 360TYS / L360TYSMotor Power HP 100 / 125 / 150Freq [(Hz) / RPM]¹ (60) / 900Voltage 460 / 575Insulation² F / H / High AmbientWeight³ [lbs. (kg)] L360TYS - 3115 (1416)
FEET
GPM
100
90
80
70
60
50
40
30
20
10
0
100
HD
S 50
L
HD
S 75
L
HD
S 10
0 L
HD
S 15
0 L
HD
S 20
0 L
HD
S 25
0 L
200300
400500
7501000
15002000
30005000
7500
Discharge Size [in. (mm)] 3" (75)Impeller Diameter [in. (mm)] 13.38" (340)Min. Impeller Diameter [in. (mm)] 10.70" (272)Max Solid Size in. (mm) 1.38" (35)Motor Frame Size 250TY / 320TYSMotor Power HP 25 / 30 / 40 / 50 / 60 / 75Freq [(Hz) / RPM]¹ (60) / 1200 & 1800Voltage 230 / 460 / 575Insulation² F / H / High AmbientWeight³ [lbs. (kg)] 250TY - 747 (340) / 320TYS - 1347 (613) Discharge Size [in. (mm)] 4" (100)Impeller Diameter [in. (mm)] 13.38" (340)Min. Impeller Diameter [in. (mm)] 10.70" (272)Max Solid Size in. (mm) 1.56" (40)Motor Frame Size 250TY / 320TYSMotor Power HP 25 / 30 / 40 / 50 / 60 / 75Freq [(Hz) / RPM]¹ (60) / 1200 & 1800Voltage 230 / 460 / 575Insulation² F / H / High AmbientWeight³ [lbs. (kg)] 250TY - 790 (359) / 320TYS - 1489 (677) Discharge Size [in. (mm)] 6" (150)Impeller Diameter [in. (mm)] 16.93" (430)Min. Impeller Diameter [in. (mm)] 13.60" (345)Max Solid Size in. (mm) 2.16" (55)Motor Frame Size 320TY / 360 TYS / L360TYSMotor Power HP 40 / 50 / 60 / 75 / 100 / 125 / 150 Freq [(Hz) / RPM]¹ (60) / 900 & 1200Voltage 460 / 575Insulation² F / H / High AmbientWeight³ [lbs. (kg)] 320TY - 2216 (1007) / L360TYS - 2633 (1192) Discharge Size [in. (mm)] 8" (200)Impeller Diameter [in. (mm)] 18.50" (470)Min. Impeller Diameter [in. (mm)] 14.80" (376)Max Solid Size in. (mm) 2.36" (60)Motor Frame Size 320TY / 360TYS / L360TYSMotor Power HP 40 / 50 / 60 / 75 / 100 / 125 / 150 Freq [(Hz) / RPM]¹ (60) / 900 & 1200Voltage 460 / 575Insulation² F / H / High AmbientWeight³ [lbs. (kg)] 320TY - 2333 (1056) / L360TYS - 2750 (1244)
150# ANSI “B 16.5” Flange
ASTM A532 CI. III Type AHigh Chrome Constructionfor Liquid End Components
Power and Control Cable Entry
Thermal Overload Sensors
416 Stainless Steel Shaft(17-4 PH & 316SS Optional)
Optional Explosion-Proof MotorEnclosure per Class 1 Groups C&D(UL Listed and CSA Certified)
Bearing Box with Heavy-Duty BallBearings Sealed and Greased for life
Dual Moisture Sensor Probes
Integrated Lifting Points(Optional Lifting Bail Available)
F Class Installation Standard(H Optional & 90°C High
Ambient Models Available)
Heavy-Duty Cast Ductile IronMotor Housing Components
Particle Ejection Ports
Internal Slurry (Continuous Run DryCapable) or Explosion-Proof Seal
316 Stainless Steel & 17-4 PHNon-Cast Wet End Components Standard
(Alloy 2205 Optional)
Agitator
Screened Inlet
POWER GENERATION
– Coal Pile Runoff– Coal Crusher Sumps– Coal Tunnel Sumps– Coal Fines Recovery– FGD Blowdown Sumps– Bottom Ash Transport– Fly Ash Sumps and Ponds– Wastewater and Basement Sumps
SAND & GRAVEL
– Weir Overflow– Dust Suppression– Recycle Water– Wheel Wash Pump– Cyclone Feed– Dredging– Barge Unloading
PUMP & PAPER / FOOD PROCESSING
– Wood Yard Runoff– Wastewater and Basement Sumps– Food Processing Waste– Juicer Sumps
MINING / STEEL
– Mine Dewatering– Collection & Runoff Sumps– Emergency Dump Pond– Tailings Pond Cleanout– Kaolin Clay– Red Mud Recovery– Magnetite Recovery– Clarifier Sludge– Slag Pits– Scale Pits– Swarf Boxes– Flume Flushers– Interceptor Pumps
Keystone HDS Medium-Head Hydraulic Performance
FEET
GPM
220
200
180
160
140
120
100
80
60
40
0
100
HD
S 75
M
HD
S 10
0 M
HD
S 15
0 M
HD
S 20
0 M
200300
400500
7501000
15002000
25003000
4000
The Keystone HDS delivers continuous, heavy-duty performance with a full range of design options. Built to handle your toughest applications!
Standard Features
316 Stainless Steel & 17-4 PH Hardware
High Chrome IronConstruction
Particle Ejection Ports
Agitator
Internal Slurry Seal
316 Stainless SteelFasteners Standard
1 50 HZ Frequency Available2 Class F- 120°F Class H- 160°F High Ambient-190°F3 Weight Subject to Motor Size
HD
S 50
LH
DS
75L
HD
S 10
0LH
DS
150L
HD
S 20
0L
HD
S 75
MH
DS
100M
HD
S 15
0MH
DS
200M
HD
S 25
0L
C
M
Y
CM
MY
CY
CMY
K
Keystone_Brochure_PRINT.pdf 2 13-07-31 10:52 AM
Keystone HDS Low-Head Hydraulic Performance
Discharge Size [in. (mm)] 2" (50)Impeller Diameter [in. (mm)] 8.46" (215)Min. Impeller Diameter [in. (mm)] 6.77" (172)Max Solid Size in. (mm) 0.63" (16)Motor Frame Size 180TY / 210TYSMotor Power HP 5 / 7.5 / 10 / 15 / 20Freq [(Hz) / RPM]¹ (60) / 1200 & 1800Voltage 230 / 460 / 575Insulation² F / H / High AmbientWeight³ [lbs. (kg)] 180 TY - 349 (159) / 210 TYS - 464 (211) Discharge Size [in. (mm)] 3" (75)Impeller Diameter [in. (mm)] 8.46" (215)Min. Impeller Diameter [in. (mm)] 6.77" (172)Max Solid Size in. (mm) 0.86" (22)Motor Frame Size 180TY / 210TYSMotor Power HP 5 / 7.5 / 10 / 15 / 20Freq [(Hz) / RPM]¹ (60) / 1200 & 1800Voltage 230 / 460 / 575Insulation² F / H / High AmbientWeight³ [lbs. (kg)] 180TY - 371 (168) / 210TYS - 484 (221) Discharge Size [in. (mm)] 4" (100)Impeller Diameter [in. (mm)] 9.05" (230)Min. Impeller Diameter [in. (mm)] 7.24" (184)Max Solid Size in. (mm) 1.26" (32)Motor Frame Size 180TY / 210TYSMotor Power HP 5 / 7.5 / 10 / 15 / 20Freq [(Hz) / RPM]¹ (60) / 1200 & 1800Voltage 230 / 460 / 575Insulation² F / H / High AmbientWeight³ [lbs. (kg)] 180TY - 403 (182) / 210TYS - 518 (235) Discharge Size [in. (mm)] 6" (150)Impeller Diameter [in. (mm)] 9.84" (250)Min. Impeller Diameter [in. (mm)] 7.82" (200)Max Solid Size in. (mm) 1.26" (32)Motor Frame Size 250TY / 320TYSMotor Power HP 25 / 30 / 40 / 50 / 60 / 75Freq [(Hz) / RPM]¹ (60) / 1200 & 1800Voltage 460 / 575Insulation² F / H / High AmbientWeight³ [lbs. (kg)] 250TY - 1058 (482) / 320TYS - 1461 (664) Discharge Size [in. (mm)] 8" (200)Impeller Diameter [in. (mm)] 14.76" (375)Min. Impeller Diameter [in. (mm)] 11.81" (300)Max Solid Size in. (mm) 1.58" (32)Motor Frame Size 320TY / 360TYS / L360TYSMotor Power HP 40 / 50 / 60 / 75 / 100 / 125 / 150 Freq [(Hz) / RPM]¹ (60) / 900 & 1200Voltage 460 / 575Insulation² F / H / High AmbientWeight³ [lbs. (kg)] 320TY - 2015 (916) / L360TYS - 2430 (1100) Discharge Size [in. (mm)] 10" (250)Impeller Diameter [in. (mm)] 20.47" (520)Min. Impeller Diameter [in. (mm)] 16.37" (416)Max Solid Size in. (mm) 2.2" (56)Motor Frame Size 360TYS / L360TYSMotor Power HP 100 / 125 / 150Freq [(Hz) / RPM]¹ (60) / 900Voltage 460 / 575Insulation² F / H / High AmbientWeight³ [lbs. (kg)] L360TYS - 3115 (1416)
FEET
GPM
100
90
80
70
60
50
40
30
20
10
0
100
HD
S 50
L
HD
S 75
L
HD
S 10
0 L
HD
S 15
0 L
HD
S 20
0 L
HD
S 25
0 L
200300
400500
7501000
15002000
30005000
7500
Discharge Size [in. (mm)] 3" (75)Impeller Diameter [in. (mm)] 13.38" (340)Min. Impeller Diameter [in. (mm)] 10.70" (272)Max Solid Size in. (mm) 1.38" (35)Motor Frame Size 250TY / 320TYSMotor Power HP 25 / 30 / 40 / 50 / 60 / 75Freq [(Hz) / RPM]¹ (60) / 1200 & 1800Voltage 230 / 460 / 575Insulation² F / H / High AmbientWeight³ [lbs. (kg)] 250TY - 747 (340) / 320TYS - 1347 (613) Discharge Size [in. (mm)] 4" (100)Impeller Diameter [in. (mm)] 13.38" (340)Min. Impeller Diameter [in. (mm)] 10.70" (272)Max Solid Size in. (mm) 1.56" (40)Motor Frame Size 250TY / 320TYSMotor Power HP 25 / 30 / 40 / 50 / 60 / 75Freq [(Hz) / RPM]¹ (60) / 1200 & 1800Voltage 230 / 460 / 575Insulation² F / H / High AmbientWeight³ [lbs. (kg)] 250TY - 790 (359) / 320TYS - 1489 (677) Discharge Size [in. (mm)] 6" (150)Impeller Diameter [in. (mm)] 16.93" (430)Min. Impeller Diameter [in. (mm)] 13.60" (345)Max Solid Size in. (mm) 2.16" (55)Motor Frame Size 320TY / 360 TYS / L360TYSMotor Power HP 40 / 50 / 60 / 75 / 100 / 125 / 150 Freq [(Hz) / RPM]¹ (60) / 900 & 1200Voltage 460 / 575Insulation² F / H / High AmbientWeight³ [lbs. (kg)] 320TY - 2216 (1007) / L360TYS - 2633 (1192) Discharge Size [in. (mm)] 8" (200)Impeller Diameter [in. (mm)] 18.50" (470)Min. Impeller Diameter [in. (mm)] 14.80" (376)Max Solid Size in. (mm) 2.36" (60)Motor Frame Size 320TY / 360TYS / L360TYSMotor Power HP 40 / 50 / 60 / 75 / 100 / 125 / 150 Freq [(Hz) / RPM]¹ (60) / 900 & 1200Voltage 460 / 575Insulation² F / H / High AmbientWeight³ [lbs. (kg)] 320TY - 2333 (1056) / L360TYS - 2750 (1244)
150# ANSI “B 16.5” Flange
ASTM A532 CI. III Type AHigh Chrome Constructionfor Liquid End Components
Power and Control Cable Entry
Thermal Overload Sensors
416 Stainless Steel Shaft(17-4 PH & 316SS Optional)
Optional Explosion-Proof MotorEnclosure per Class 1 Groups C&D(UL Listed and CSA Certified)
Bearing Box with Heavy-Duty BallBearings Sealed and Greased for life
Dual Moisture Sensor Probes
Integrated Lifting Points(Optional Lifting Bail Available)
F Class Installation Standard(H Optional & 90°C High
Ambient Models Available)
Heavy-Duty Cast Ductile IronMotor Housing Components
Particle Ejection Ports
Internal Slurry (Continuous Run DryCapable) or Explosion-Proof Seal
316 Stainless Steel & 17-4 PHNon-Cast Wet End Components Standard
(Alloy 2205 Optional)
Agitator
Screened Inlet
POWER GENERATION
– Coal Pile Runoff– Coal Crusher Sumps– Coal Tunnel Sumps– Coal Fines Recovery– FGD Blowdown Sumps– Bottom Ash Transport– Fly Ash Sumps and Ponds– Wastewater and Basement Sumps
SAND & GRAVEL
– Weir Overflow– Dust Suppression– Recycle Water– Wheel Wash Pump– Cyclone Feed– Dredging– Barge Unloading
PUMP & PAPER / FOOD PROCESSING
– Wood Yard Runoff– Wastewater and Basement Sumps– Food Processing Waste– Juicer Sumps
MINING / STEEL
– Mine Dewatering– Collection & Runoff Sumps– Emergency Dump Pond– Tailings Pond Cleanout– Kaolin Clay– Red Mud Recovery– Magnetite Recovery– Clarifier Sludge– Slag Pits– Scale Pits– Swarf Boxes– Flume Flushers– Interceptor Pumps
Keystone HDS Medium-Head Hydraulic Performance
FEET
GPM
220
200
180
160
140
120
100
80
60
40
0
100
HD
S 75
M
HD
S 10
0 M
HD
S 15
0 M
HD
S 20
0 M
200300
400500
7501000
15002000
25003000
4000
The Keystone HDS delivers continuous, heavy-duty performance with a full range of design options. Built to handle your toughest applications!
Standard Features
316 Stainless Steel & 17-4 PH Hardware
High Chrome IronConstruction
Particle Ejection Ports
Agitator
Internal Slurry Seal
316 Stainless SteelFasteners Standard
1 50 HZ Frequency Available2 Class F- 120°F Class H- 160°F High Ambient-190°F3 Weight Subject to Motor Size
HD
S 50
LH
DS
75L
HD
S 10
0LH
DS
150L
HD
S 20
0L
HD
S 75
MH
DS
100M
HD
S 15
0MH
DS
200M
HD
S 25
0L
C
M
Y
CM
MY
CY
CMY
K
Keystone_Brochure_PRINT.pdf 2 13-07-31 10:52 AM
Heavy Duty Submersible Slurry Pumps For Industrial Applications
STANDARD HDS FEATURES
Run Dry Slurry Seal
Mechanical seal configuration designed for prolonged motor operation in severe duty slurry applications
Double mechanical seals operate in an oil chamber where components are isolated from the pumped slurry
Carbon-Ni Resist face (upper) & Tungsten Carbide face (lower) w/ stainless hardware
Particle Ejection Ports
Expels solids to extend seal life
Maintains minimum flow during closed valve operation
HDS Agitator
Solids are propelled into suspension by the mixing
action of the blades
Heavy Duty XP Seal
Carbon-Ni Resist faces & 316 Stainless Steel hardware for internal seal
Tungsten Carbide faces & 316 StainlessSteel hardware for external seal
Seal Leak Detector
Senses moisture if the external seal fails and sends a signal to the control panel
Water Jacket
Provides motor cooling for run dry & hot sump applications
www.keystonepumps.com
Control Panel
Simplex / Duplex
Ground Fault & Ground Check Monitoring
Custom Designs Available
Jet Ring
Settled solids are induced into suspension
by the water jetting action of the nozzles
Lifting Bail
Allows for a central lift point / Low temperature operation design
OPTIONAL HDS FEATURES
Unit 307 – 2999 Underhill AveBurnaby, B.C. V5A 3C2
Toll-free: 1.888.875.3323Phone: 604.227.3555
Fax: 604.229.0494Email: [email protected]
www.keystonepumps.com2013 Keystone Pumps, All rights reserved
C
M
Y
CM
MY
CY
CMY
K
Keystone_Brochure_PRINT.pdf 1 13-07-31 10:52 AM