rubber molded table of contents - innova€¦ · (rev 0704) rubber molded series table of contents...
TRANSCRIPT
(REV 0704)
RUBBER MOLDED SERIESTable of Contents
Rubber Molded Bulkhead Connector Mates . . . . . . . . . . . 50-AIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-1General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-2Maintenance Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . 50-3Typical Right Angle and Straight Connector Indexing . . . 50-4Typical Mated Assembly and Options . . . . . . . . . . . . . . . . . 50-5RMA-FS and Associated Parts . . . . . . . . . . . . . . . . . . . . . . 50-6
RMA-MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-6RMA-FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-6RMA-FS R/A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-6RMA-MP-SL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-6RMA-FS-SL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-6RMA-FSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-6RMA-MPD-LP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-6RMA-MPD-HP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-6RMA-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-7XSA-BC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-7XSA-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-7XSB-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-7XSC-BC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-8XSC-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-8
VMA-FS and Associated Parts . . . . . . . . . . . . . . . . . . . . . . 50-9VMA-MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-9VMA-FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-9VMA-FS R/A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-9VMA-MP-SL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-9VMA-FS-SL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-9VMA-FSD-LP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-9VMA-FSD-HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-9VMA-MPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-9VMA-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-10VSA-BC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-10VSA-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-10VSB-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-10
RMF-FS and Associated Parts . . . . . . . . . . . . . . . . . . . . . 50-11RMF-MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-11RMF-FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-11RMF-FS R/A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-11RMF-FSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-11RMF-MPD-HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-11RMF-MPD-LP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-11XSF-BC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-12XSF-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-12XSFDE-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-12
VMF-FS and Associated Parts . . . . . . . . . . . . . . . . . . . . . 50-13VMF-MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-13VMF-FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-13VMF-FS R/A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-13VMF-FSD-HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-13VMF-FSD-LP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-13VMF-MPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-13VMF-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-14VSF-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-14
LMG-FS and Associated Parts . . . . . . . . . . . . . . . . . . . . . 50-15LMG-MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-15LMG-FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-15LMG-FS R/A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-15LMG-FSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-15LMG-MPD-LP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-15LMG-MPD-HP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-15LSG-BC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-16LSG-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-16LSG-BC-SC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-17LSG-BC-HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-18
RMG-FS and Associated Parts . . . . . . . . . . . . . . . . . . . . . 50-19RMG-MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-19RMG-FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-19
RMG-FS R/A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-19RMG-FS WOC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-19RMG-MP WOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-19RMG-FSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-19RMG-MPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-19RMG-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-20XSG-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-20XSG-BCL-P-R/A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-20XSG-PBC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-21XSG-PBCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-21XSG-PBCLM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-21RMGS-BC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-22RMGS-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-22
VMG-FS and Associated Parts . . . . . . . . . . . . . . . . . . . . . 50-23VMG-MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-23VMG-FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-23VMG-FS R/A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-23VMG-FS WOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-23VMG-MP WOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-23VMG-FSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-23VMG-MPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-23VMG-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-24VSG-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-24VSG-PBC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-24VSG-PBCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-25VSG-PBCLM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-25
RMK-FS and Associated Parts . . . . . . . . . . . . . . . . . . . . . 50-26RMK-MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-26RMK-FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-26RMK-FS R/A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-26RMK-FS WOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-26RMK-MP WOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-26RMK-FSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-26RMK-MPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-26RMK-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-27XSK-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-27XSK-DEBCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-27
VMK-FS and Associated Parts . . . . . . . . . . . . . . . . . . . . . 50-28VMK-MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-28VMK-FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-28VMK-FS R/A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-28VMK-FS WOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-28VMK-MP WOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-28VMK-FSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-28VMK-MPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-28VMK-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-29VSK-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-29
Special Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-30Locking Sleeves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-31
A-FLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-32A-MLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-32F-FLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-32F-MLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-32VSF-FLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-32VSF-MLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-32G-FLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-32G-MLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-32G-FLS-S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-32G-MLS-S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-32G-FLS-X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-32G-MLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-32K-FLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-32K-MLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-32K-FLS-S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-32K-MLS-S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-32K-FLS-X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-32K-MLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-32
Rubber Molded Quick Reference Mating Table . . . . . . . 50-33
50-A (REV 0704)
1/4-28
XSA-BC
THD5/16-24
THD1/4-28
THD3/8-24
THDTHD3/8-241/4-28
THD5/16-24
THD5/16-24
THD
VSA-BC RMA-BCLXSA-BCL
VMA-BCLVSA-BCL
XSB-BCL XSC-BC XSC-BCL
RMA FSVMA FS
RMA-FS R/A
VSB-BCL
Page No. 50-7 50-7 50-10 50-7 50-10 50-8 50-850-10
NOTE: Torque values referenced in this literature assume installation intodry metal threads. Please contact the factory for recommendations.
LSG-BC LSG-BCLLSG-BC HP
THD3/4-16
LSG-BC SC(formerly LSK-BC SC)
LMG FS
LMG FS R/A
NOTE:LSG-3-BC HP: 1/2-20LSG-4-BC HP: 9/16-18LSG-6-BC HP: 9/16-18
11/16-16THD
3/8-24THD
3/8-24THD
XSFDE-BCL(formerly XSDE-BCL) XSF-BC XSF-BCL
RMF FS
RMF FS R/A
50-12Page No. 50-12 50-12
1/2-20THD
VMF-BCLVSF-BCL
VMF FS
VMF FS R/A
50-14Page No.50-16Page No. 50-16 50-20 50-17
NOTE:LSG-3-BC: 1/2-20LSG-4-BC: 9/16-18LSG-6-BC: 9/16-18
NOTE:LSG-3-BCL: 1/2-20LSG-4-BCL: 9/16-18LSG-6-BCL: 9/16-18
RUBBER MOLDED BULKHEAD CONNECTOR MATESVISUAL INDEX
50-B (REV 0704)
1-14THD
1-14THD
VMK FSRMK FS
RMK FS R/A
XSKDE-BCL
1 1/2-14THD
RMK-BCLXSK-BCL
VMK-BCLVSK-BCL
Page No. 50-27 50-27 50-29
XSG-PBC
1/2-20THD
1/2-20THD
VSG-PBC
1/2-20THD
XSG-PBCLM
1/2-20THD
XSG-PBCL
3/4-16THD
3/4-16THD
RMG FSVMG FS
1/2-20THD
VSG-PBCLM
1/2-20THD
VSG-PBCL
RMG FS R/A
NOTE:RMGS-BC (1/2" NPT)RMGS-BCL (3/4" NPT)
VMG-BCLVSG-BCL
RMG-BCL 50-20RMGS-BC 50-22RMGS-BCL 50-22XSG-BCL 50-20XSG-BCL-P-R/A 50-20
Page No. 50-21 50-2150-24 50-25
50-21 50-25 50-24
NOTE: Torque values referenced in this literature assume installation into dry metal threads. Please contact the factory for recommendations.
RUBBER MOLDED BULKHEAD CONNECTOR MATESVISUAL INDEX
50-1 (REV 0704)
INTRODUCTION
Our standard rubber molded series typically consists of an in-line female neoprene connector mated to a glassreinforced epoxy (XS) bulkhead connector. Various sizes are available ranging from single contact connectors upthrough 12 contact connectors. Most are available with pins and sockets reversed to help prevent mismating ofconnectors, which otherwise look identical. This also allows for socket type contacts in a connector where there isa possibility of a "power-on" situation. Many of the bulkhead type connectors are available in 316 Stainless Steel,and can also be manufactured of any of the exotic metals. Male in-line connectors round out the series allowingfor in-line mated sets not requiring bulkhead penetration. In addition, the WOC (without cable) type connectorsallow for field installation in the event that a connector is damaged while at sea and needs replacing, or for longcable lengths that make cable transportation cost prohibitive.
The time proven rubber molded series is one of our most inexpensive lines and has been used on all types ofunderwater instrumentation including: underwater lighting, communications, ROV's, thermistor arrays, hydrophonearrays, and all types of sonar systems. The contacts are gold plated per ASTM-B-488 and the series is rated up to20,000 psi in a mated condition.
PART NUMBERING SYSTEMCONNECTORS
RM G - 6 - FS - R/A
Right Angle (optional)
Female Socket
Number of Contacts
Size
Rubber Molded
Bulkhead ConnectorsLS Glass Reinforced Epoxy- Special Version
RM Metal Shell
VM Reversed Metal Shell
VS Reversed Glass Reinforced Epoxy
XS Glass Reinforced Epoxy
BC Bulkhead Connector
BCL BC w/Locking Thread
C COAX
DE Double Ended
HP High Pressure
IDC Inboard Disconnect
P Pigtails
In-Line ConnectorsLM Rubber Molded-Special Version
RM Rubber Molded
VM Reversed Rubber Molded
FS Female Socket
FSD Female Socket Dummy
MP Male Plug
MPD Male Plug Dummy
FI Field Installable
HP High Pressure
LP Low Pressure
SL Slip-on Series
WOC Without Cable
R/A Right Angle
SC Solder Cup
TH Thermistor Housing
50-2 (REV 0704)
GENERAL INFORMATIONRUBBER MOLDED AND ASSOCIATED SERIES
APPLICATIONS:Standard, Reversed Rubber Molded Series
Applications requiring light to medium ruggednessHazardous environmentsField installable applications
Glass Reinforced Epoxy SeriesApplications requiring medium ruggednessHazardous environmentsPower transmissionSignal telemetry
Metal Shell SeriesApplications requiring heavy ruggednessHazardous, rugged environmentsPower transmissionSignal telemetry
CABLE:Rubber Molded Series
Connector's power capability may be limited by amperage and voltage rating of cable to which it ismolded to. With the exception of field installable connectors, the in-line series are provided on a stan-dard 18" length of 18 AWG SO cable unless otherwise specified.
Glass Reinforced Epoxy Series & Metal Shell SeriesConnector's power capability may be limited by amperage and voltage rating of pigtails.Customer must specify if pigtails are to be applied.
NOTE: Torque values referenced in this literature assume installation intodry metal threads. Please contact the factory for recommendations.
50-3 (REV 0704)
MAINTENANCE PROCEDURESCONNECTORS
MAINTENANCE
The following procedures detail the maintenance requirements for the Rubber Molded Series and theirassociated parts. Even though this procedure appears simple, only qualified technicians should per-form the maintenance. If connectors are periodically unmated SEA CON® recommends the following:
1. Before unmating ensure connectors are free of foreign contaminates. Visually check for andnote any damage or abnormalities.
2. After unmating visually check for and note any damage, cuts or abnormalities.
3. Clean any grease, moisture or foreign particles from connectors and sealing surface area.
4. In the event the internal contact surfaces are dirty or have been exposed to water, the connec-tor should be flushed with distilled or deionized water and thoroughly dried.
5. The surface should be dried using a low pressure (15 - 25 psi) gas stream of dry nitrogen orfiltered compressed air (dry nitrogen is preferred). This drying procedure ensures the removal ofany small foreign particles.
6. Electrically test the connector in accordance with the parameters of the system.
7. Apply a thin film of an appropriate silicone grease or spray to the sealing surface. Cover/protectconnector from foreign contaminates until ready to mate.
*Torque values are noted with actual part and can be found in pages to follow.
1. Only qualified technicians should perform installation and torquing operations.
2. *Torque values specified apply only when connector is installed in a metal housing.
3. Torque values listed are maximum values not to be exceeded.
4. Locking sleeves are finger/hand tightened only.
INSTALLATION & TORQUE OPERATIONS
NOTE: Torque values referenced in this literature assume installation intodry metal threads. Please contact the factory for recommendations.
50-4 (REV 0704)
Visual Index (3) Cable
(Straight Entry)
OptionalLockingSleeve
Cable(Right Angle Entry To Connector)
Visual Index
Right AngleMolded Body(Elastomeric Material)
Cable-RightAngle Entry-InLine With Index
RUBBER MOLDED SERIESTYPICAL RIGHT ANGLE AND STRAIGHT CONNECTOR INDEXING
In the case of right angle connectors, the cable is always perpendicular to the index, as shown
50-5 (REV 0704)
RUBBER MOLDED SERIESTYPICAL MATED ASSEMBLY AND OPTIONS
CABLENeoprene outer jacketsupplied on our standardcables
RUBBER MOLDEDCONNECTOR
OPTIONAL LOCKING SLEEVE (long)For use with straight connectorsonly. This long type of lockingsleeve helps to eliminate conductorbreakage at termination joint byeliminating flexing at joint area.
ELECTRICAL CONTACTScopper alloy, hard goldplated per ASTM-B-488.
BULKHEAD CONNECTORSMaterial -Glass Reinforced Epoxyeliminates all dissimilar metalproblems
O-RINGBuna N, 70 Durometer isstandard. O-Rings suppliedwith all connectors.All O-Rings must belubricated with a thin film ofsilicon or DC grease.
OPTIONAL WATER. TIGHT MOLDPolyurethane usually used;neoprene optional (molded)To specify pigtails add.P afterconnector callout.
OPTIONAL INDIVIDUAL PIGTAILSTeflon, 18" Long.Longer lengths available
CABLEOr solid rubber for dummy
RUBBER MOLDEDCONNECTOR
RIGHT ANGLE CONNECTOR
OPTIONAL LOCKING SLEEVEFor use with straight or right
BULKHEAD CONNECTORS
If IDC’s are intended for usespecify pins on low pressureside when ordering bulkheadconnectors. Solder pots arestandard.
INBOARD DISCONNECT (IDC)Not Water Tight (Optional)
INBOARD NUT & WASHERSET (SST)(Optional)
NOTE: Torque values referenced in this literature assume installation into dry metal threads. Please contact the factory forrecommendations.
MATINGTo ensure that the connectors are not damaged during mating/unmating, it is important to practice proper connect and discon-nect procedures.
INCORRECT CORRECT
50-6 (REV 0704)
RMA-FS AND ASSOCIATED PARTSSTANDARD RUBBER MOLDED
IN-LINE SERIES
Material: Special Neoprene, moldedContacts: Copper Alloy, Hard Gold Plated per ASTM B488Cable: 1 N 2Voltage Rating: 600 VDC-contact factory for higher voltage requirementsPressure Rating, Mated: up to 20,000 psi
RMA-MP
RMA-FS
RMA-FS R/A
.87
1.50
2.00
1.06
1.81
RMA-1-FSRMA-1-MP
1#16
2.50
LOCKING SLEEVES
A-MLS-D (AVAILABLE FOR RMA-MP)A-FLS-D (AVAILABLE FOR RMA-FS, RMA-FS-R/A)
SLIP-ON SERIES
Material: Special Neoprene, moldedContacts: Brass, Hard Gold Plated per ASTM-B-488Voltage Rating: 600 VDC-contact factory for higher voltage requirementsPressure Rating, Mated: up to 20,000 PSI
RMA-FS-SL
1.53
2.32
RMA-MP-SL
1.06
1.85
VISUALINDEX
SOCKETPINSOLDERCUP SOLDER
CUP
(Uses Locking Sleeve: A-MLS-D) (Uses Locking Sleeve: A-FLS-D)
Notes: Specify exact wire diameter when ordering. Maximum wire DIA=0.09 inch
DUMMY CONNECTORS
RMA-FSD MATES TO RMA-MPRMA-MPD-LP/HP TO RMA-FS & RMA-FS-R/AMaterial: Special Neoprene, moldedPressure Rating, Mated:RMA-FSD (20,000PSI)RMA-MPD-LP (<4,000 PSI)RMA-MPD-HP (4,000 – 20,000 PSI) Male Contact Required
50-7 (REV 0704)
RMA-FS AND ASSOCIATED PARTSMATEABLE BULKHEAD CONNECTORS
BULKHEAD CONNECTORS & MOUNTING REQUIREMENT(MATES TO RMA-FS & RMA-FS-R/A & RMA FS SL)Dummy Connector: RMF FSD
Part Name: RMA-BCLRMA-BCLRMA-BCLRMA-BCLRMA-BCLMaterial: 316 Stainless St., Internal Insulation-Special NeopreneContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure Rating, Mated: up to 20,000 psi
RMA-BCL;RMA-BCL;RMA-BCL;RMA-BCL;RMA-BCL; Special insulating neoprene is compressionmolded to the metal body forming a reliable seal. Themetal body can be made of stainless steel, aluminum orother metals.
This Connector utilizes a facial o-ring seal to thebulkhead.
600VDC
RMA-BCL1#16
.63
5/16-24 UNF-2AMounting Torque15 INCH LBS.
O-RING (2-012)
.63
1.25
Part Name: XSA-BCXSA-BCXSA-BCXSA-BCXSA-BCMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure Rating, Mated: up to 20,000 psi
600VDC
.37
XSA-BC1#16
1/4-28 UNFMounting Torque6 INCH LBS.
O-RING (2-009)
600VDC
XSA-BCL1#16
2.00
.31 .62 .18
1.8
.40 .45 .18
.12
600VDC
XSB-BCL1#16
.62
.62
2.00
.31 .62 .18
.12
5/16-24 UNFMounting Torque8 INCH LBS.
O-RING (2-012)
1/4-28 UNFMounting Torque6 INCH LBS.
O-RING (2-012)
.052
.050
.370
.360
.015
.005.015.005
.370
.360 .052.050R R
1/4-28 UNF-2B THREADMOUNTING REQUIREMENT
FOR XSA BC
32
32
32
32
XSA-BCXSA-BCXSA-BCXSA-BCXSA-BC; The smallest standardconnector in our non-metallic series, features ano-ring in the thread relief area. Available in single contact.
XSA-BCLXSA-BCLXSA-BCLXSA-BCLXSA-BCL; These are miniature, single contact connec-tors which feature a locking sleeve provision. The o-ring islocated on a step under the hex and seals by flushmounting to the bulkhead. Same Material and Pressureas XSA-BC.
XSB-BCLXSB-BCLXSB-BCLXSB-BCLXSB-BCL; A miniature connector body very similar to theXSA BCL, but utilizes a smaller installation thread. Thesmall thread size requires care in installation to avoiddamaging or cracking. The o-ring is located on a stopunder the hex and seals by flush mounting to the bulk-head. Same Material and Pressure as XSA-BC.
NOTE: Torque values referenced in this literature assumeinstallation into dry metal threads. Please contact thefactory for recommendations.
50-8 (REV 0704)
RMA-FS AND ASSOCIATED PARTSMATEABLE BULKHEAD CONNECTORS
BULKHEAD CONNECTORS & MOUNTING REQUIREMENT(MATES TO RMA-FS & RMA-FS-R/A & RMA FS SL)Dummy connector RMA FSD
Part Names: XSC-BC, XSC-BCLXSC-BC, XSC-BCLXSC-BC, XSC-BCLXSC-BC, XSC-BCLXSC-BC, XSC-BCLMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure Rating, Mated: up to 10,000 psi
XSC-BC, XSC-BCL;XSC-BC, XSC-BCL;XSC-BC, XSC-BCL;XSC-BC, XSC-BCL;XSC-BC, XSC-BCL; These connectors feature a radial typeo-ring seal, good for up to 10,000 PSI, mated. Available only insingle contact.
NOTE: Torque values referenced in this literature assume installation into drymetal threads. Please contact the factory for recommendations.
600VDC
600VDC
XSC-BC1#16
XSC-BCL1#16
2.0
.50 .56 .18.288
3/8-24 UNFMounting Torque12 INCH LBS.
O-RING (2-011)
3/8-24 UNFMounting Torque12 INCH LBS.
O-RING (2-011)
2.09
.37 .56 .18.288 .18
3/8-24 UNF-2B THREADMOUNTING REQUIREMENT
.439
.437
.020 R
.005 R.289.287
.68
.50
32
XSC-BCLXSC-BCLXSC-BCLXSC-BCLXSC-BCL
XSC-BCXSC-BCXSC-BCXSC-BCXSC-BC
50-9 (REV 0704)
VMA-FS AND ASSOCIATED PARTSREVERSED RUBBER MOLDED
VMA-MP
VMA-FS
VMA-1-FSVMA-1-MP
1#16
.87
1.50
2.00
1.06
1.81
2.50
VMA-FS R/A
VMA-MP SL
1.06
1.81
VMA-FS-SL
PIN
BOOT
SOLDERCUP
BOOT
SOCKET
1.53
SOLDERCUP
IN-LINE SERIESIN-LINE SERIESIN-LINE SERIESIN-LINE SERIESIN-LINE SERIES
Material: Special Neoprene, MoldedContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Cable: 1 N 2Voltage Rating: 600 VDC-contact factory for higher voltage requirementsPressure Rating, Mated: up to 20,000 psi
LOCKING SLEEVES
A-MLS-D (AVAILABLE FOR VMA-MP)A-FLS-D (AVAILABLE FOR VMA-FS, VMA-FS-R/A)
DUMMY CONNECTORS
VMA-FSD-LP MATES TO VMA-MPVMA-FSD-HP MATES TO VMA-MPVMA-MPD MATES TO VMA-FS & VMA-FS-R/AMaterial: Special Neoprene, MoldedPressure Rating, Mated:VMA-FSD-LP < 4,000 PSI (CONNECTOR BODY W/O MALE PIN)VMA-FSD-HP 4,000 - 20,000PSIVMA-MPD 20,000 PSI
SLIP-ON SERIES
Material: Special Neoprene, MoldedContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Voltage Rating: 600 VDC-contact factory for higher voltagerequirements Pressure Rating, Mated: up to 20,000 psi
Notes: Specify exact wire diameter when ordering. Maximum wire DIA=0.09 INCH
(Uses Locking Sleeve: A-MLS-D)(Uses Locking Sleeve: A-FLS-D)
50-10 (REV 0704)
VMA-FS AND ASSOCIATED PARTSMATEABLE BULKHEAD CONNECTORS
600VDC
VMA-BCL1#16
.63
5/16-24 UNF-2AMounting Torque8 INCH LBS.
O-RING (2-012)
.63
1.25
.44
VSA-BC1#16
5/16-24 UNFMounting Torque:5 INCH LBS.
O-RING (2-010)
VSA-BCL1#16
1.7
.38 .62 .18
1.7
.50 .18
.12
VSB-BCL1#16
.62
.052
.050
.420
.410
.015
.005.015.005
.420
.410 .052.050R R
5/16-24 UNF-2B THREADMOUNTING REQUIREMENT
FOR VSA BC
.62
.62
5/16-24 UNFMounting Torque:8 INCH LBS.
O-RING (2-012)
1/4-28 UNFMounting Torque:4 INCH LBS.
O-RING (2-012)
1.7
.38 .62 .18
.12
RECESSED SOCKET
RECESSED SOCKET
RECESSED SOCKET
32
32
32
32
BULKHEAD CONNECTORS & MOUNTING REQUIREMENTBULKHEAD CONNECTORS & MOUNTING REQUIREMENTBULKHEAD CONNECTORS & MOUNTING REQUIREMENTBULKHEAD CONNECTORS & MOUNTING REQUIREMENTBULKHEAD CONNECTORS & MOUNTING REQUIREMENT(MATES TO VMA-FS & VMA-FS-R/A & VMA-FS SL)Dummy Connector: VMA-FS D HP or VMA FS D LP
VMA-BCL;VMA-BCL;VMA-BCL;VMA-BCL;VMA-BCL; Special insulating neoprene iscompression molded to the metal body forming areliable seal. The metal body can be made of stainlesssteel, aluminum or other metals.This connector utilizes a facial o-ring to seal to thebulkhead.
Part Name: VMA-BCLVMA-BCLVMA-BCLVMA-BCLVMA-BCLMaterial: 316 Stainless St., Internal Insulation-Special NeopreneContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure Rating, Mated: up to 20,000 psi
VSA-BCVSA-BCVSA-BCVSA-BCVSA-BC; The smallest standard connector in our non-metallic series, features ano-ring in the thread relief area. Available in singlecontact.
Part Names: VSA-BC, VSA-BCL, VSB-BCLVSA-BC, VSA-BCL, VSB-BCLVSA-BC, VSA-BCL, VSB-BCLVSA-BC, VSA-BCL, VSB-BCLVSA-BC, VSA-BCL, VSB-BCLMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure Rating, Mated: up to 20,000 psi
VSA-BCLVSA-BCLVSA-BCLVSA-BCLVSA-BCL; Miniature single contact connectors whichfeature a locking sleeve provision. The o-ring is locatedon a step under the hex and seals by flush mounting tothe bulkhead.
VSB-BCLVSB-BCLVSB-BCLVSB-BCLVSB-BCL; This is a miniature connector body verysimilar to the VSA-BCL, but utilizes a smaller installationthread. The small thread size requires care in installa-tion to avoid damaging or cracking. The o-ring islocated on a stop under the hex and seals by flushmounting to the bulkhead.
Note: Torque values referenced in this literature assumeinstallation into dry metal threads. Plese contactthe factory for recommendations.
50-11 (REV 0704)
RMF 1 MPRMF 2 MP
RMF 1 FS R/ARMF 2 FS R/A
RMF 1 FSRMF 2 FS
RMF-C-FS/MPCOAX
22 AWG/20 Ω(Cable: CN4 or CN5)
600 VDC
RMF-1-FS/MP1#14
(Cable: 18/1SO)or Equivalent
600 VDC
RMF-2-FS/MP2#16
(Cable: 18/2SJO)
300 VDC
1.60
1.18
2.45
.81
1.4
∅.47∅.47
VISUALINDEX
1
RMF-FS AND ASSOCIATED PARTSSTANDARD RUBBER MOLDED
IN-LINE SERIES
Material: Special Neoprene, MoldedContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488See Specific Configuration for Voltage RatingPressure Rating, Mated: up to 10,000 psi
LOCKING SLEEVES
F-MLS-D (AVAILABLE FOR RMF-MP)XSF-FLS-D (AVAILABLE FOR RMF-FS, RMF-FS-R/A)
DUMMY CONNECTORS
RMF-FSD MATES TO RMF-MPRMF-MPD-HP MATES TO RMF-FS & RMF-FS –R/ARMF-MPD-LP MATES TO RMF-FS & RMF-FS-R/A
Material: Special Neoprene, MoldedPressure Rating, Mated:
RMF-FSD (10,000 PSI)RMF-MPD-HP (HIGH PRESSURE, 4,000 PSI-10,000 PSI, CONTACT REQUIRED)
RMF-MPD-LP (LOW PRESSURE, < 4,000 PSI, NO CONTACT REQUIRED)
Note: Specify number of conductors when ordering
50-12 (REV 0704)
RMF-FS AND ASSOCIATED PARTSMATEABLE BULKHEAD CONNECTORS
XSF-BC
XSF-BCL
2.0
.50 .56 .18
.288
3/8-24 UNFMounting Torque12 INCH LBS.
O-RING (2-011)
3/8-24 UNFMounting Torque12 INCH LBS.
O-RING (2-011)
2.00
.31 .56 .18
.288 .18
3/8-24 UNF-2B THREADMOUNTING REQUIREMENT
.439
.437
.020 R
.005 R.289.287
.68
.50
XSF-BC/BCLCOAX
#22 AWG/20 Ω
XSF-1-BC/BCL1#14
XSF-2-BC/BCL2#16
XSFDE-BCL
11/16-16 UNFMounting Torque20 INCH LBS.
O-RING (2-021)
2.81.31 .87 .31
.37
1.25
LOW PRESSURE HIGH PRESSURE
XSF-1-BCLDE1#14
XSF-2-BCLDE2#16
BULKHEAD CONNECTORS & MOUNTING REQUIREMENT(MATES TO RMF-FS & RMF-FS-R/A & RMF FS WOC)Dummy Connector RMF-FSD
Part Names: XSF-BC, XSF-BCLXSF-BC, XSF-BCLXSF-BC, XSF-BCLXSF-BC, XSF-BCLXSF-BC, XSF-BCLMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per MIL-G-45204Pressure Rating, Mated: up to 10,000 psi
XSF-BC;XSF-BC;XSF-BC;XSF-BC;XSF-BC; Features radial o-ring seal.
XSF-BCL;XSF-BCL;XSF-BCL;XSF-BCL;XSF-BCL; These connectors feature a locking sleeve provi-sion and utilize a radial o-ring seal.
Part Name: XSFDE-BCLXSFDE-BCLXSFDE-BCLXSFDE-BCLXSFDE-BCLMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold PlatedPressure Rating, Mated: up to 10,000 psi
NOTE: Torque values referenced in this literature assumeinstallation into dry metal threads. Please contact thefactory for recommendations.
Description: A double-ended connector which accepts amating connector on either end. The same locking sleeve alsofits both ends. This connector utilizes a facial o-ring seal to thebulkhead.
(FORMERLY KNOWN AS XSDE-BCL)
50-13 (REV 0704)
VMF-FS AND ASSOCIATED PARTSREVERSED RUBBER MOLDED
VMF-FS R/A
VMF-FS
VMF-MP
VMF-C-FS600 VDCCABLE:
CN4 or CN5
VMF-1-FS600 VDCCABLE:
18/1SO orEQUIVALENT
VMF-2-FS300 VDCCABLE:
18/2 SJO
IN-LINE SERIES
Material: Special Neoprene, MoldedContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Voltage Rating: See specific configurationPressure Rating, Mated: up to 20,000 psi
LOCKING SLEEVES
VSF-MLS-D (AVAILABLE FOR VMF-MP)VSF-FLS-D (AVAILABLE FOR VMF-FS, VMF-FS-R/A)
DUMMY CONNECTORS
VMF-FSD-HP MATES TO VMF-MPVMF-FSD-LP MATES TO VMF-MP
VMF-MPD MATES TO VMF-FS & VMF-FS -R/A
MATERIAL: SPECIAL NEOPRENE, MOLDEDPRESSURE RATING, MATED:
VMF-MPD 10,000 PSIVMF-FSD-HP (HIGH PRESSURE, 4,000-10,000 PSI CONTACT REQUIRED)
VMF-FSD-LP (LOW PRESSURE, < 4,000 PSI NO CONTACT REQUIRED)
Note: Specify number of conductors when ordering
50-14 (REV 0704)
VMF-FS AND ASSOCIATED PARTSMATEABLE BULKHEAD CONNECTORS
1
2
1
2
VSF-C-BCLCOAX
#22 AWG/20Ω
VSF-1-BCL1#14
VSF-2-BCL2#16
1/2-20 UNF-2AMounting Torque15 INCH LBS. O-RING (2-114)
1.33
.58
.93FLATS
BULKHEAD CONNECTORS(MATES TO VMF-FS & VMF-FS-R/A & VMF FS WOC)Dummy Connector: VMF-FSD
Part Name: VMF-BCLVMF-BCLVMF-BCLVMF-BCLVMF-BCLMaterial: 316, Stainless SteelContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure Rating, Mated: up to 20,000 psi
VMF-BCL;VMF-BCL;VMF-BCL;VMF-BCL;VMF-BCL; Special insulating neoprene is perma-nently molded to the metal shell. These types ofconnectors are used where physical abuse wouldbe too great for the non-metallic (glass reinforcedepoxy) series.
Part Name: VSF-BCLVSF-BCLVSF-BCLVSF-BCLVSF-BCLMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure Rating, Mated: up to 20,000 psi
VSF-BCL;VSF-BCL;VSF-BCL;VSF-BCL;VSF-BCL; Available in coax, 1 and 2 contacts,features a facial o-ring seal to the bulkhead.
NOTE: Torque values referenced in this literature assumeinstallation into dry metal threads. Please contact thefactory for recommendations.
VMF-BCL
1.33
1 1
2
VMF-C-BCLCOAX
#22 AWG/20Ω
VMF-1-BCL1#14
VMF-2-BCL1#16
.93FLATS
A
A
O-RING (2-114)
1/2-20 UNF-2AMounting Torque50 INCH LBS.
50-15 (REV 0704)
LMG-FS AND ASSOCIATED PARTSSTANDARD RUBBER MOLDED
LMG-FS
LMG-MP
LMG-3-FS1#142#16
(Cable: 18/3SO)
LMG-4-FS1#143#16
(Cable: 18/4SO)
LMG-6-FS1#145#16
(Cable: 18/6SO)
LMG-FS R/A
∅.75 ∅.75
2.00
.502.15
1.12
2.15
2.69
IN-LINE SERIES
Material: Special Neoprene, MoldedContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Voltage Rating: 600 VDC-contact factory for higher voltage requirementsPressure Rating, Mated: up to 20,000 psi
LOCKING SLEEVES
G-MLS-D (AVAILABLE FOR LMG-MP)G-FLS-D (AVAILABLE FOR LMG-FS, LMG-FS-R/A)
DUMMY CONNECTORS
LMG-FSD MATES TO LMG-MPLMG-MPD LP/HP MATES TO LMG-FS & LMG-FS-R/A
MATERIAL: SPECIAL NEOPRENE, MOLDEDPRESSURE RATING, MATED:
LMG-FSD (20,000 PSI)LMG-MPD-HP (HIGH PRESSURE, 4,000 PSI-20,000 PSI, CONTACT REQUIRED)
LMG-MPD-LP (LOW PRESSURE, < 4,000 PSI NO CONTACT REQUIRED)
Note: Specify number of conductors when ordering
50-16 (REV 0704)
LMG-FS AND ASSOCIATED PARTSMATEABLE BULKHEAD CONNECTORS
LSG-3-BCL
LSG-4-BCL
LSG-6-BCL
.68HEX
1 #142 #16
∅.93
.18.18
.50
1.40
1/2-20 UNFMounting Torque15 INCH LBS. O-RING (2-017)
.68HEX
1 #143 #16
∅.93
.18.18
.50
1.40
9/16-18 UNFMounting Torque18 INCH LBS. O-RING (2-017)
.68HEX
1 #145 #16
∅.93
.25.18
.50
1.56
9/16-18 UNFMounting Torque18 INCH LBS. O-RING (2-017)
.93HEX
.93HEX
.93HEX
1 #142 #16
1 #143 #16
1 #145 #16
1/2-20 UNFMounting Torque15 INCH LBS. O-RING (2-017)
9/16-18 UNFMounting Torque18 INCH LBS. O-RING (2-017)
9/16-18 UNFMounting Torque18 INCH LBS. O-RING (2-017)
∅.93
∅.93
∅.93
.18
.33.50
1.50
.18
.33
.50
1.50
.18
.33.50
1.58
LSG-6-BC
LSG-4-BC
LSG-3-BC
Part Name: LSG-BC, LSG-BCLLSG-BC, LSG-BCLLSG-BC, LSG-BCLLSG-BC, LSG-BCLLSG-BC, LSG-BCLMates to LMG-FS, LMG-FS R/ADummy Connector - LMG-FS DMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure Rating, Mated: up to 3,000 psi
LSG-BC, LSG-BCL;LSG-BC, LSG-BCL;LSG-BC, LSG-BCL;LSG-BC, LSG-BCL;LSG-BC, LSG-BCL; These non-metallic connec-tors utilize a facial o-ring seal to the bulkhead. TheLSG-BCL has a locking sleeve provision.
NOTE: Torque values referenced in this literature assume installation into dry metal threads.Please contact the factory for recommendations.
Note: Does not mate to RMG- FS or RMG-FS R/A
Note: Does not mate to RMG- FS or RMG-FS R/A
Note: Also mates to RMG-FS and RMG-FS R/A
50-17 (REV 0704)
LMG-FS AND ASSOCIATED PARTSMATEABLE BULKHEAD CONNECTORS
∅1.06
.35
.18
.97
1.93
3/4-16 UNFMounting Torque70 INCH LBS. O-RING (2-016)
.87HEX
LSG-3-BC-SC
.43
.35
.18
.97
1.93
3/4-16 UNFMounting Torque70 INCH LBS. O-RING (2-016)
.87HEX
LSG-4-BC-SC
∅1.06
.43
.35
.18
.97
2.03
3/4-16 UNFMounting Torque70 INCH LBS. O-RING (2-016)
.87HEX
LSG-6-BC-SC
∅1.06
.43
3/4-16 UNF-2B THREADMOUNTING REQUIREMENT
LSG BC SC
.752
.750.020 R
.005 R.351.349
LSG-3-BC-SC1#142#16
LSG-4-BC-SC1#143#16
LSG-6-BC-SC1#145#16
32
Part Name: LSG-BC-SC (Formerly known as LSK-BC-SC)LSG-BC-SC (Formerly known as LSK-BC-SC)LSG-BC-SC (Formerly known as LSK-BC-SC)LSG-BC-SC (Formerly known as LSK-BC-SC)LSG-BC-SC (Formerly known as LSK-BC-SC)Mates to LMG-FS, LMG-FS R/ADummy Connector: LMG-FSDMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure Rating, Mated: up to 5,000 psi
LSG-BC-SC;LSG-BC-SC;LSG-BC-SC;LSG-BC-SC;LSG-BC-SC; These non-metallic connectors utilize aradial o-ring seal to the bulkhead.
Note: Does not mate to RMG-FS or RMG-FS R/A.
Note: Also mates to RMG-FS and RMG-FS R/A.
Note: Does not mate to RMG-FS or RMG-FS R/A.
NOTE: Torque values referenced in this literature assume installation into dry metal threads.Please contact the factory for recommendations.
50-18 (REV 0704)
∅.93
.18
.50
1.64
.68HEX
LSG-3-BC-HP
1/2-20 UNFMounting Torque15 INCH LBS. O-RING (2-017)
.43
LSG-4-BC-HP
LSG-6-BC-HP
1 #142 #16
∅.93
.18
.50
1.64
.68HEX
9/16-18 UNFMounting Torque18 INCH LBS. O-RING (2-017)
.431 #143 #16
∅.93
.18
.50
1.74
.68HEX
9/16-18 UNFMounting Torque18 INCH LBS. O-RING (2-017)
.431 #145 #16
LMG-FS AND ASSOCIATED PARTSMATEABLE BULKHEAD CONNECTORS
BULKHEAD CONNECTORS(MATES TO LMG FS & LMG-FS-R/A)Dummy Connector: LMG-FSD
Part Name: LSG-BC-HPLSG-BC-HPLSG-BC-HPLSG-BC-HPLSG-BC-HPMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure Rating, Mated: up to 10,000 psi
LSG-BC-HP;LSG-BC-HP;LSG-BC-HP;LSG-BC-HP;LSG-BC-HP; These non-metallic connectors feature afacial o-ring seal to the bulkhead.
Note: Does not mate to RMG-FS or RMG-FS R/A
Note: Does not mate to RMG-FS or RMG-FS R/A
Note: Also mates to RMG-FS and RMG-FS R/A
NOTE: Torque values referenced in this literature assume installation into drymetal threads. Please contact the factory for recommendations.
50-19 (REV 0704)
RMG-FS AND ASSOCIATED PARTSSTANDARD RUBBER MOLDED
RMG-1-FSMP-WOC
1 #10 AWG
RMG-2-FSMP-WOC
1 #10 AWG1 #14 AWG
RMG-4-FSMP-WOC
1 #14 AWG3 #16 AWG
RMG-3-FSMP-WOC
1 #10 AWG2 #14 AWG
1
23
1 2
34
RMG FS R/A
RMG FS
RMG-1-FS1#10
(Cable: 18/1SO)or Equivalent
2.06
1.13
2.9
2.6
∅.75∅.75
RMG-MP
2.13
11
223
1
23
41 5
42
36
151
4
32
RMG-2-FS1#101#14
(Cable: 18/2SO)
RMG-3-FS1#102#14
(Cable: 18/3SO)
RMG-4-FS1#143#16
(Cable: 18/4SO)
RMG-5-FS1#144#16
(Cable: 18/5SO)
RMG-6-FS1#145#16
(Cable: 18/6SO)
IN-LINE SERIES
Material: Special Neoprene, MoldedContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Voltage Rating: 600 VDC-contact factory for higher voltage requirementsPressure Rating, Mated: up to 20,000 psi
Note: Available with grippers, must specify.
WOC CONNECTORS
Part Name: RMG-FS WOC, RMG-MP WOCRMG-FS WOC, RMG-MP WOCRMG-FS WOC, RMG-MP WOCRMG-FS WOC, RMG-MP WOCRMG-FS WOC, RMG-MP WOCMaterial: Special Neoprene, MoldedContacts: Brass, Hard Gold Plated per ASTM-B-488Voltage Rating: 600 VDC-contact factory for higher voltage requirements PressureRating, Mated: up to 20,000 psi
Note: WOC stands for “without cable.” The connectors are supplied as shown below for installation in the field and/or to non-neoprene jacketed cables, Bonding can be achieved by molding to the connectors shown using polyurethane with appropriate primers.
LOCKING SLEEVES
G-MLS-D (AVAILABLE FOR RMG-MP, RMG-MP WOC)G-FLS-D (AVAILABLE FOR RMG-FS, RMG-FS-R/A, RMG-FS WOC)G-MLS-S (AVAILABLE FOR RMG-MP, RMG-MP WOC )G-FLS-S (AVAILABLE FOR RMG-FS, RMG-FS-R/A, RMG-FS WOC)G-FLS-X (AVAILABLE FOR RMG-FS) Must specify cable O.D. when ordering G-FLS-X
DUMMY CONNECTORS
RMG-FSD MATES TO RMG-MP, BCL & XSG-BCL,XSG-PBC, XSG-PBCL & XSG-PBCLM
RMG-MPD MATES TO RMG-FS & RMG FS-R/A
MATERIAL: SPECIAL NEOPRENE, MOLDEDPRESSURE RATING, MATED:
RMG-FSD (20,000 PSI)RMG-MPD-LP (LOW PRESSURE < 4,000 PSI)
RMG-MPD-HP (4,000 PSI-20,000 PSI) Contact Required
Note: Must specify cable OD when using G-FLS-X Note: specify number of conductors when ordering
50-20 (REV 0704)
RMG-FS AND ASSOCIATED PARTSMATEABLE BULKHEAD CONNECTORS
11
22 3
12
34
1
RMG-1-BCLXSG-1-BCL
1 #10
RMG-2-BCLXSG-2-BCL
1 #101 #14
RMG-3-BCLXSG-3-BCL
1 #102 #14
RMG-4-BCLXSG-4-BCL
1 #143 #14
RMG-BCL
1 3/8HEX
3/4-16 UNFMounting Torque85 INCH LBS. O-RING (2-213)
.87 1.18
2
34
1
RMG-5-BCLXSG-5-BCL
1 #144 #16
2
34
1
RMG-6-BCLXSG-6-BCL
1 #145 #16
INDEX
56
3/4-16 UNFMounting Torque85 INCH LBS. O-RING (2-213)
1.18
XSG-BCL
.50
3/4-16 UNFMounting Torque85 INCH LBS. O-RING (2-213)
1.18
XSG-BCL LT
.87
1/2-20 UNFMounting Torque15 INCH LBS
O-RING (2-017)
1.00
XSG-BCL-P-R/A
1.25
.87
18.0
1
22 3
12
3 4
1
XSG-2-BCL-P-R/A1 #101 #14
XSG-3-BCL-P-R/A1 #102 #14
XSG-4-BCL-P-R/A1 #143 #16
BULKHEAD CONNECTORS(MATES TO RMG FS & RMG-FS-R/A & RMG FS WOC)Dummy Connector RMG FS D
Part Name: RMG-BCLRMG-BCLRMG-BCLRMG-BCLRMG-BCLMaterial: 316 Stainless St., Internal Insulation-Special NeopreneContacts: Copper Alloy, Hard Gold Plated per ASTM-B-448Pressure Rating, Mated: up to 20,000 psi
RMG-BCL;RMG-BCL;RMG-BCL;RMG-BCL;RMG-BCL; Special Insulating neoprene is permanently moldedto the metal shell. These types of connectors are used wherephysical abuse would be too great for the non-metallic (glassreinforced epoxy) series. The RMG BCL has a locking sleeveprovision and utilizes a facial O-ring seal to the bulkhead.
Part Name: XSG-BCLXSG-BCLXSG-BCLXSG-BCLXSG-BCLMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per ASTM-B-448Pressure Rating, Mated: up to 20,000 psi
XSG-BCL;XSG-BCL;XSG-BCL;XSG-BCL;XSG-BCL; One of our oldest connectors in the non-metallicseries, with male pin as shown. Connector is one homoge-neously molded unit. Available with different thread lengthsas indicated. TheXSG BCL has a locking sleeve provisionand utilizes a facial O-ring seal to the bulkhead.
Part Name: XSG-BCL-P-R/AXSG-BCL-P-R/AXSG-BCL-P-R/AXSG-BCL-P-R/AXSG-BCL-P-R/AMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per ASTM-B-448Pigtails; teflon insulated #18 AWGPressure Rating, Mated: up to 20,000 psi
XSG-BCL-P-R/A;XSG-BCL-P-R/A;XSG-BCL-P-R/A;XSG-BCL-P-R/A;XSG-BCL-P-R/A; A non-metallic low profile rightangle bulkhead connector featuring a locking sleeveprovision and utilizing a facial o-ring seal to thebulkhead.
NOTE: Torque values referenced in this literature assumeinstallation into dry metal threads. Please contactthe factory for recommendations.
50-21 (REV 0704)
RMG-FS AND ASSOCIATED PARTSMATEABLE BULKHEAD CONNECTORS
11
22 3
12
3 4
1
XSG-1-PBC1 #10
XSG-2-PBC1 #101 #14
XSG-3-PBC1 #102 #14
XSG-4-PBC1 #143 #16
1/2-20 UNFMounting Torque15 INCH LBS.
O-RING (2-012)
1.55
.38
1/2-20 UNFMounting Torque15 INCH LBS.
O-RING (2-012)
18.00
.55
2.06
.81
18.00
.62
.62
∅.94
.62
1/2-20 UNF-2B THREADMOUNTING REQUIREMENT
.504
.502.020 R
.083
.081
XSG-PBC
XSG-PBCL
11
22 3
12
3 4
1
XSG-1-PBCL1 #10
XSG-2-PBCL1 #101 #14
XSG-3-PBCL1 #102 #14
XSG-4-PBCL1 #143 #16
.941
1
22 3
12
3 4
1
XSG-1-PBCLM1 #10
XSG-2-PBCLM1 #101 #14
XSG-3-PBCLM1 #102 #14
XSG-4-PBCLM1 #143 #16
1/2-20 UNFMounting Torque15 INCH LBS.
O-RING (2-017)
1.59
.46
18.00
.50XSG-PBCLM
BULKHEAD CONNECTORS & MOUNTING REQUIREMENT(MATES TO RMG FS & RMG-FS-R/A & RMG-FS WOC)Dummy Connector: RMG-FSD
Part Name: XSG-PBC, XSG-PBCL: XSG-PBC, XSG-PBCL: XSG-PBC, XSG-PBCL: XSG-PBC, XSG-PBCL: XSG-PBC, XSG-PBCLMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pigtails: teflon insulated #18 AWGPressure Rating, Mated: up to 5,000 psi
XSG-PBC;XSG-PBC;XSG-PBC;XSG-PBC;XSG-PBC; Small footprint non-metallic connectorutilizing an o-ring in the thread relief area to seal tothe bulkhead.
Part Name: XSG-PBCLMXSG-PBCLMXSG-PBCLMXSG-PBCLMXSG-PBCLMMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pigtails: teflon insulated #18 AWGPressure Rating, Mated: up to 5,000 psi
XSG-PBCLM;XSG-PBCLM;XSG-PBCLM;XSG-PBCLM;XSG-PBCLM; Non-metallic connector utilizing afacial o-ring seal to the bulkhead. Features alocking sleeve provision.
NOTE: Torque values referenced in this literature assume installation into dry metalthreads. Please contact the factory for recommendations.
XSG-PBCL;XSG-PBCL;XSG-PBCL;XSG-PBCL;XSG-PBCL; Small footprint non-metallic connec-tor utilizing an o-ring in the thread relief area to sealto the bulkhead. Features a locking sleeveprovision.
50-22 (REV 0704)
RMG-FS AND ASSOCIATED PARTSMATEABLE BULKHEAD CONNECTORS
2
RMGS-1-BC/BCL1 #10 AWG
RMGS-2-BC/BCL1 #10 AWG1 #14 AWG
RMGS-3-BC/BCL1 #10 AWG2 #14 AWG
RMGS-4-BC/BCL1 #14 AWG3 #16 AWG
RMGS-BCL
RMGS-BC
.87HEX FLATS
1.06HEX FLATS
1/2 -14 NPT
.62
1.32
.75
3/4 -14 NPT
.75
1.21
.62
1
2
1
32
1
3
4
BULKHEAD CONNECTORS(MATES TO RMG FS & RMG-FS-R/A & RMG-FS WOC)Dummy Connector: RMG-FSD
Part Names: RMGS-BC, RMGS-BCLRMGS-BC, RMGS-BCLRMGS-BC, RMGS-BCLRMGS-BC, RMGS-BCLRMGS-BC, RMGS-BCLMaterial: 316 Stainless SteelContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure Rating, Mated: up to 5,000 psi
RMGS-BC;RMGS-BC;RMGS-BC;RMGS-BC;RMGS-BC; Features a stainless steel body,insulating neoprene, and pipe thread for sealing tobulkhead. No O-Ring required for sealing.
NOTE: Torque values referenced in this literature assume installation into dry metalthreads. Please contact the factory for recommendations.
RMGS-BCL;RMGS-BCL;RMGS-BCL;RMGS-BCL;RMGS-BCL; Features a stainless steel body,insulating neoprene, and pipe thread for sealing tobulkhead. No O-Ring required for sealing. Featuresa locking sleeve provision.
50-23 (REV 0704)
VMG-FS AND ASSOCIATED PARTSREVERSED RUBBER MOLDED
VMG-1-FS-WOC1 #14
VMG-2-FS-WOC1 #141 #16
VMG-3-FS-WOC1 #142 #16
VMG-4-FS-WOC1 #143 #16
INDEX INDEX
∅.75∅.75 ∅.56∅.56
3.00
1.12
2.37
.50
∅.75
VMG-MP
2.06
2.9
2.13
1.13
∅.75
2.6
VISUAL INDEX(IN-LINE WITH CONTACT #1)
VMG-FS
VMG-FS R/A
VMG-1-FS1 #14
(Cable: 18/1SO)or Equivalent
VMG-2-FS1 #141 #16
(Cable: 18/2SO)
VMG-3-FS1 #142 #16
(Cable: 18/3SO)
VMG-4-FS1 #143 #16
(Cable: 18/4SO)
IN-LINE SERIES
Material: Special Neoprene, MoldedContacts: Copper Alloy, Hard Gold Plated per ASTM-B-448Voltage Rating: 600 VDC-contact factory for higher voltagerequirementsPressure Rating, Mated: up to 20,000 psi
LOCKING SLEEVES
G-MLS-D (AVAILABLE FOR VMG-MP (VMG-MP-WOC))G-FLS-D (AVAILABLE FOR VMG-FS, VMG-FS-R/A, VMG-FS WOCG-FLS-X (AVAILABLE FOR VMG-FS) Must specify cable O.D.
Note: Must specify cable OD when using G-FLS-X
DUMMY CONNECTORS
VMG-FSD MATES TO VMG-MPVMG-MPD MATES TO VMG-FS & VMG-FS-R/A & VMG-FS WOC
MATERIAL: SPECIAL NEOPRENE, MOLDEDPRESSURE RATING, MATED:
VMG-FSD-LP (LOW PRESSURE < 4,000PSI, NO CONTACT REQUIRED)VMG-FSD-HP (4,000-20,000 PSI, CONTACT IS REQUIRED)
VMG-MPD (20,000 PSI)
Note: specify number of conductors when ordering
WOC CONNECTORS
Part Names: VMG-FS WOC, VMG-MPVMG-FS WOC, VMG-MPVMG-FS WOC, VMG-MPVMG-FS WOC, VMG-MPVMG-FS WOC, VMG-MP WOCWOCWOCWOCWOCMaterial: Special Neoprene, MoldedContacts: Copper Alloy, Hard Gold Plated per ASTM-B-448Voltage Rating: 600 VDC-contact factory for higher voltage requirementsPressure Rating, Mated: up to 20,000 psi
Note: WOC stands for “without cable.” The connectors are supplied as shown below for installation in the field and/or to non-neoprene jacketed cables. Bonding can be achieved by molding to the connectors shown using polyurethane with appropriate primers.
50-24 (REV 0704)
VMG-FS AND ASSOCIATED PARTSMATEABLE BULKHEAD CONNECTORS
1 3/8HEX
VMG-BCL
11
22 3
12
3 4
1
VMG-1-BCLVSG-1-BCL
1 #14
VMG-2-BCLVSG-2-BCL
1 #141 #16
VMG-3-BCLVSG-3-BCL
1 #142 #16
VMG-4-BCLVSG-4-BCL
1 #143 #16
.87 1.18
3/4-16 UNF O-RING (2-213) O-RING (2-213)
VSG-BCL
O-RING (2-213)
VSG-BCL LT
1.18.50
1.18.87
3/4-16 UNF
3/4-16 UNF
.62
11
22 3
12
3 4
1
VSG-1-PBC1 #14
VSG-2-PBC1 #141 #16
VSG-3-PBC1 #142 #16
VSG-4-PBC1 #143 #16
1.55
.38
18.00
.55
1/2-20 UNFMounting Torque15 INCH LBS.
O-RING (2-012)
VSG-PBC
1/2-20 UNF-2B THREADMOUNTING REQUIREMENT
.504
.502
.020 R
.083
.08132
BULKHEAD CONNECTORS & MOUNTING REQUIREMENT(MATES TO VMG-FS, VMG-FS-R/A & VMG-FS WOC)Dummy Connector VMG-FS D
Part Name: VMG-BCLVMG-BCLVMG-BCLVMG-BCLVMG-BCLMaterial: 316 Stainless St., Internal Insulation-Special NeopreneContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure Rating, Mated: up to 20,000 psi
VMG-BCL;VMG-BCL;VMG-BCL;VMG-BCL;VMG-BCL; Special insulating neoprene is permanently moldedto the metal shell. These types of connectors are used wherephysical abuse would be too great for the non-metallic (glassreinforced epoxy) series. The VMG BCL features a locking sleeveprovision and utilizes a facial o-ring seal to the bulkhead.
Part Name: VSG-BCLVSG-BCLVSG-BCLVSG-BCLVSG-BCLMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure Rating, Mated: up to 20,000 psi
VSG-BCL;VSG-BCL;VSG-BCL;VSG-BCL;VSG-BCL; One of our oldest connectors in the non-metallicseries, with female sockets as shown. Connector is one homo-geneously molded unit. Available with different thread lengthsas indicated. The VSG BCL features a locking sleeve provisionand utilizes a facial o-ring seal to the bulkhead.
Part Name: VSG-PBCVSG-PBCVSG-PBCVSG-PBCVSG-PBCMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pigtails: teflon insulated #18 AWGPressure Rating, Mated: up to 5,000 psi
VSG-PBC;VSG-PBC;VSG-PBC;VSG-PBC;VSG-PBC; Non-Metallic connector utilizing an o-ring in thethread relief area to seal the bulkhead.
NOTE: Torque values referenced in this literature assume installation into dry metalthreads. Please contact the factory for recommendations.
50-25 (REV 0704)
VMG-FS AND ASSOCIATED PARTSMATEABLE BULKHEAD CONNECTORS
BULKHEAD CONNECTORS & MOUNTING REQUIREMENT(MATES TO VMG FS & VMG-FS-R/A)
Part Name: VSG-PBCLVSG-PBCLVSG-PBCLVSG-PBCLVSG-PBCLMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pigtails: Teflon insulated #18 AWGPressure Rating, Mated: up to 5,000 psi
.62
11
22 3
12
3 4
1
VSG-1-PBCL1 #14
VSG-2-PBCL1 #141 #16
VSG-3-PBCL1 #142 #16
VSG-4-PBCL1 #143 #16
1.55
.81
18.00
.62
1/2-20 UNFMounting Torque15 INCH LBS.
O-RING (2-012)
VSG-PBCL
1/2-20 UNF-2B THREADMOUNTING REQUIREMENT
.504
.502
.020 R
.083
.081
∅.94
RECESSEDSOCKETS
Part Name: VSG-PBCLMVSG-PBCLMVSG-PBCLMVSG-PBCLMVSG-PBCLMMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pigtails: Teflon insulated #18 AWGPressure Rating, Mated: up to 5,000 psi
VSG-PBCLM;VSG-PBCLM;VSG-PBCLM;VSG-PBCLM;VSG-PBCLM; Non-Metallic connector featuring alocking sleeve provision. VSG-PBCLM utilizes afacial o-ring seal to the bulkhead.
11
22 3
12
3 4
1
VSG-1-PBCLM1 #14
VSG-2-PBCLM1 #141 #16
VSG-3-PBCLM1 #142 #16
VSG-4-PBCLM1 #143 #16
1.59
.46
18.00
.50
1/2-20 UNFMounting Torque15 INCH LBS.
O-RING (2-017)
VSG-PBCLM
.94
RECESSEDSOCKETS
NOTE: Torque values referenced in this literature assume installation into drymetal threads. Please contact the factory for recommendations.
VSG-PBCL;VSG-PBCL;VSG-PBCL;VSG-PBCL;VSG-PBCL; Non-metallic connector that featuresa locking sleeve provision and utilizes an o-ring inthe thread relief area to seal to the bulkhead.
50-26 (REV 0704)
RMK-1/0-FS1 #1/0
(Cable: 1/0 Welding)
RMK-6/8-FS1 #6 AWG1 #8 AWG
(Cable: 8/2SO)
RMK-2-FS1 #10 AWG1 #14 AWG
(Cable: 18/2SO)
RMK-1-FS1 #8 AWG
(Cable: 8/1SO)
RMK-3-FS1 #10 AWG2 #14 AWG
(Cable: 18/3SO)
RMK-4-FS1 #10 AWG3 #14 AWG
(Cable: 18/4SO)
RMK-5-FS1 #10 AWG4 #14 AWG
(Cable: 18/5SO)
RMK-6-FS1 #14 AWG5 #16 AWG
(Cable: 18/6SO)
RMK-7-FS1 #14 AWG6 #16 AWG
(Cable: 18/7SO)
RMK-8-FS1 #14 AWG7 #16 AWG
(Cable: 18/8SO)
RMK-9-FS1 #14 AWG8 #16 AWG
(Cable: 18/10SO)
RMK-12-FS1 #14 AWG11 #16 AWG
(Cable: 18/12SO)
2.6
∅1.06
VISUAL INDEX(IN-LINE WITH CONTACT #1)
SEALINGSURFACE
∅1.06
3.13
2.75
1.63
2.31RMK-FS
RMK-MP
RMK-FS R/A
VISUALINDEX
9
10
12
11
1
2
1
2
1
23
4
1
2
3
4
1
2
3
5
4
1
2
3
5
6
4
1
2
3
5
6
7
4
1
2
35
6
7
8
4
1
2
3
5
6
7
8
9
4
1
2
3
5
6
7
8
RMK-FS AND ASSOCIATED PARTSSTANDARD RUBBER MOLDED
RMK-1/0-FS1 #1/0
RMK-6/8-FS1 #6 AWG1 #8 AWG
RMK-2-FS1 #10 AWG1 #14 AWG
RMK-1-FS1 #8 AWG
RMK-3-FS1 #10 AWG2 #14 AWG
RMK-4-FS1 #10 AWG3 #14 AWG
RMK-5-FS1 #10 AWG4 #14 AWG
RMK-6-FS1 #14 AWG5 #16 AWG
RMK-7-FS1 #14 AWG6 #16 AWG
RMK-8-FS1 #14 AWG7 #16 AWG
RMK-9-FS1 #14 AWG8 #16 AWG
RMK-12-FS1 #14 AWG
11 #16 AWG
1011
8
1
2
1
2
1
23
1
2
3
4
1
2
34
5
1
2
34
5
6
1
2
34
5
6 7
1
2
3
45
6
71
2
3
45
6
7
8
9
1
2
3
456
7
8 912
IN-LINE SERIES
Material: Special Neoprene, MoldedContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Voltage Rating: 600 VDC-contact factory for higher voltage requirementsPressure Rating, Mated: up to 20,000 psi
Note: Available with grippers, must specify.
LOCKING SLEEVES
K-MLS-D (AVAILABLE FOR RMK-MP & RMK-MP WOC)K-FLS-D (AVAILABLE FOR RMK-FS, RMK-FS-R/A, RMK-FS WOC)K-MLS-S (AVAILABLE FOR RMK-MP, RMK-MP WOC)K-FLS-S (AVAILABLE FOR RMK-FS, RMK-FS R/A & RMK-FS WOC)K-FLS-X (AVAILABLE FOR RMK-FS)
(Must specify cable O.D. when ordering K-FLS-X)
DUMMY CONNECTORS
RMK-FSD MATES TO RMK-MPRMK-MPD MATES TO RMK-FS & RMK-FS-R/A
Material: Special Neoprene, MoldedPressure Rating, Mated:
RMK-FSD (20,000 PSI)RMK-MPD-LP (LOW PRESSURE < 4,000 PSI, NO CONTACT REQUIRED)
RMK-MPD-HP (4,000-20,000 PSI CONTACT IS REQUIRED)
Note: specify number of conductors when ordering
WOC CONNECTORSWOC CONNECTORSWOC CONNECTORSWOC CONNECTORSWOC CONNECTORS
Part Names: RMK-FS WOC, RMK-MP WOCRMK-FS WOC, RMK-MP WOCRMK-FS WOC, RMK-MP WOCRMK-FS WOC, RMK-MP WOCRMK-FS WOC, RMK-MP WOCMaterial: Special Neoprene, MoldedContacts: Brass, Hard Gold Plated per ASTM-B-488Voltage Rating: 600 VDC-contact factory for higher voltage requirementsPressure Rating, Mated: up to 20,000 psi
Note: WOC stands for “without cable.” The connectors are supplied as shown below for installation in the field and/or to non-neoprene jacketed cables. Bonding can be achieved by molding to the connectors shown using polyurethane with appropriate primers. Inexpensive plastic syringes can be used as molds.
50-27 (REV 0704)
RMK-FS AND ASSOCIATED PARTSMATEABLE BULKHEAD CONNECTORS
VISUAL INDEX(IN-LINE WITH CONTACT #1)
RMK-BCL1-14 UNS
Mounting Torque130 inch lbs.
XSK-1/0-BCL1 #1/0
RMK-6/8-BCLXSK-6/8-BCL
1 #6 AWG1 #8 AWG
RMK-2-BCLXSK-2-BCL1 #10 AWG1 #14 AWG
RMK-1-BCLXSK-1-BCL1 #8 AWG
RMK-3-BCLXSK-3-BCL1 #10 AWG2 #14 AWG
RMK-4-BCLXSK-4-BCL1 #10 AWG3 #14 AWG
RMK-5-BCLXSK-5-BCL1 #10 AWG4 #14 AWG
RMK-6-BCLXSK-6-BCL1 #14 AWG5 #16 AWG
RMK-7-BCLXSK-7-BCL1 #14 AWG6 #16 AWG
RMK-8-BCLXSK-8-BCL1 #14 AWG7 #16 AWG
RMK-9-BCLXSK-9-BCL1 #14 AWG8 #16 AWG
RMK-12-BCLXSK-12-BCL1 #14 AWG11 #16 AWG
8
9
10
128
86
55
6
VISUALINDEX
VISUAL INDEX(IN-LINE WITH CONTACT #1)
1-14 UNS
Mounting Torque130 inch lbs.
.87 .87
VISUAL INDEX(IN-LINE WITH CONTACT #1)
1-14 UNS
Mounting Torque130 inch lbs.
1.25
XSK-BCL
XSK-BCL LT
XSK-DEBCL
XSK-1/0-DEBCL1 #1/0
XSK-6/8-DEBCL1 #6 AWG1 #8 AWG
XSK-2-DEBCL1 #10 AWG1 #14 AWG
XSK-1-DEBCL1 #8 AWG
XSK-3-DEBCL1 #10 AWG2 #14 AWG
XSK-4-DEBCL1 #10 AWG3 #14 AWG
XSK-5-DEBCL1 #10 AWG4 #14 AWG
XSK-6-DEBCL1 #14 AWG5 #16 AWG
XSK-7-DEBCL1 #14 AWG6 #16 AWG
6
55
6
VISUALINDEX
O-Ring (2-131)
LOW PRESSURE HIGH PRESSURE
BULKHEAD CONNECTORS(MATES TO RMK-FS & RMK-FS-R/A & RMK-FS WOC)Dummy Connector: RMK-FSD
Part Name: RMK-BCLRMK-BCLRMK-BCLRMK-BCLRMK-BCLMaterial: 316 Stainless St.; Internal Insulation: Special NeopreneContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure rating, Mated: up to 20,000 psi
RMK-BCL;RMK-BCL;RMK-BCL;RMK-BCL;RMK-BCL; Special Insulating neoprene is permanently moldedto the metal shell. These types of connectors are used wherephysical abuse would be too great for the non-metallic (glassreinforced epoxy) series. The RMK BCL has a locking sleeveprovision and utilizes a facial O-ring seal to the bulkhead.
NOTE: Torque values referenced in this literature assumeinstallation into dry metal threads. Please contact thefactory for recommendations.
Part Name: XSK-BCLXSK-BCLXSK-BCLXSK-BCLXSK-BCLMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure Rating, Mated: up to 20,000 psi
XSK-BCL;XSK-BCL;XSK-BCL;XSK-BCL;XSK-BCL; One of our oldest connectors in the non-metallicseries, with male pin as shown. Connector is one homogeneouslymolded unit. Available with different thread lengths as indicated.TheXSK BCL has a locking sleeve provision and utilizes a facialO-ring seal to the bulkhead.
Part Name: XSK-DEBCLXSK-DEBCLXSK-DEBCLXSK-DEBCLXSK-DEBCLMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure Rating, Mated: up to 20,000 psi from front side.
XSK-DEBCL;XSK-DEBCL;XSK-DEBCL;XSK-DEBCL;XSK-DEBCL; A non-metallic double ended connector whichaccepts a mating connector on either end. The same lockingsleeve also mates to both ends. This connector utilizes a facialo-ring seal to the bulkhead.
50-28 (REV 0704)
VMK-FS AND ASSOCIATED PARTSREVERSED RUBBER MOLDED
VMK-1/0-FS1 #1/0
(Cable: 1/0 Welding)
VMK-1-FS1 #8
(Cable: 8/1SO)
VMK-6/8-FS1 #61 #8
(Cable: 8/2SO)
VMK-2-FS1 #141 #16
(Cable: 18/2SO)
2.6
VISUALINDEX
VMK-MP VMK-FS
VMK-FS R/A
VMK-3S-FS1 #142 #8
(Cable: 10/3SO)
VMK-3-FS1 #142 #16
(Cable: 18/3SO)
VMK-4-FS1 #143 #16
(Cable: 18/4SO)
VMK-5-FS1 #144 #16
(Cable: 18/5SO)
VMK-6-FS1 #145 #16
(Cable: 18/6SO)
VMK-7-FS1 #146 #16
(Cable: 18/7SO)
VMK-8-FS1 #147 #16
(Cable: 18/8SO)
VMK-12-FS1 #1411 #16
(Cable: 18/12SO)
IN-LINE SERIES
Material: Special Neoprene, MoldedContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Voltage Rating: 600 VDC-contact factory for higher voltage requirementsPressure Rating, Mated: up to 20,000 psi
LOCKING SLEEVES
K-MLS-D (AVAILABLE FOR VMK-MP, VMK-MP WOC)K-FLS-D (AVAILABLE FOR VMK-FS, VMK-FS-R/A, VMK-FS WOC)
DUMMY CONNECTORS
VMK-FSD MATES TO VMK-MPVMK-MPD MATES TO VMK-FS & VMK-FS R/A
Material: Special Neoprene, MoldedPressure Rating, Mated:
VMK-FSD-LP (LOW PRESSURE < 4,000 PSI, NO CONTACT REQUIRED)VMK-FSD-HP (4,000-20,000 PSI CONTACT IS REQUIRED)
VMK-MPD (20,000 PSI, NO CONTACT REQUIRED)
Notes: Specify number of conductors when ordering
WOC CONNECTORS
Part Names: VMK-FS WOC, VMK-MP WOCMaterial: Special Neoprene, MoldedContacts: Brass, Hard Gold Plated per ASTM-B-488Voltage Rating: 600 VDC-contact factory for higher voltage requirementsPressure Rating, Mated: up to 20,000 psi
Note: WOC stands for “without cable.” The connectors are supplied as shown below for installation in the field and/or to non-neoprene jacketed cables. Bonding can be achieved by molding to the connectors shown using polyurethane with appropriate primers.
50-29 (REV 0704)
VMK-FS AND ASSOCIATED PARTSMATEABLE BULKHEAD CONNECTORS
BULKHEAD CONNECTORS(MATES TO VMK-FS & VMK-FS-R/A & VMK FS WOC)Dummy Connector VMK-FSD
Part Name: VMK-BCLVMK-BCLVMK-BCLVMK-BCLVMK-BCLMaterial: 316 Stainless St.; Internal Insulation: Special NeopreneContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure Rating, Mated: up to 20,000 psi
VMK-BCL;VMK-BCL;VMK-BCL;VMK-BCL;VMK-BCL; Special Insulating neoprene is permanently moldedto the metal shell. These types of connectors are used wherephysical abuse would be too great for the non-metallic (glassreinforced epoxy) series. The VMK BCL has a locking sleeveprovision and utilizes a facial O-ring seal to the bulkhead.
Part Name: VSK-BCLVSK-BCLVSK-BCLVSK-BCLVSK-BCLMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure Rating, Mated: up to 20,000 psi
VSK-BCL;VSK-BCL;VSK-BCL;VSK-BCL;VSK-BCL; One of our oldest connectors in the non-metallicseries, with male pin as shown. Connector is one homoge-neously molded unit. Available with different thread lengths asindicated. The VSK BCL has a locking sleeve provision andutilizes a facial O-ring seal to the bulkhead.
VMK-BCL
VMK/VSK-1/0-BCL1 #1/0
VMK/VSK-1-BCL1 #8
VMK/VSK-6/8-BCL1 #61 #8
VMK/VSK-2-BCL1 #141 #16
VISUALINDEX
VMK/VSK-3S-BCL1 #142 #8
VMK/VSK-3-BCL1 #142 #16
VMK/VSK-4-BCL1 #143 #16
VMK/VSK-5-BCL1 #144 #16
VMK/VSK-6-BCL1 #145 #16
VMK/VSK-7-BCL1 #146 #16
VMK/VSK-8-BCL1 #147 #16
VMK/VSK-12-BCL1 #14
11 #16
Mounting Torque130 inch lbs.
VSK-BCL
Mounting Torque130 inch lbs.
.87
VSK-BCL LT
Mounting Torque130 inch lbs.
1.25
.87
NOTE: Torque values referenced in this literature assume installation into drymetal threads. Please contact the factory for recommendations.
50-30 (REV 0704)
SPECIAL ASSEMBLIESCABLE MOLDS AND CABLE SPLICES
SPECIAL ASSEMBLIES
Material: Neoprene Molding per B/A X-5727 or Polyurethane; black perMIL-M-24041
Note: Length and geometric shape may vary depending on cable diameter.
B
A C
D
∅E
WYE MOLDS
BARREL MOLDS
AVAILABLEMOLDS A B C
Y-30 2 3/4 Inches 1 5/8 Inches 5/8 Inches
Y-40 4 7/8 Inches 3 1/2 Inches 1 Inches
Y-50 6 3/4 Inches 4 Inches 1 1/2 Inches
Y-70 9 1/2 Inches 5 1/2 Inches 2 Inches
AVAILABLEMOLDS D E
B-30 2 Inches 1 1/4 Inches
B-40 4 Inches 1 3/4 Inches
B-50 6 1/2 Inches 2 3/4 Inches
B-70 8 1/2 Inches 3 1/2 Inches
50-31 (REV 0704)
LOCKING SLEEVES
PART NUMBERING A - FLS - DSIZE (F) FEMALE OR (M) MALE MATERIAL
LOCKING SLEEVE(D) DELRIN, BLACK - STANDARD(S) STAINLESS STEEL(B) BRONZE; CA 630(X) LONG(TI) TITANIUM
SEA CON®’S range of locking sleeves are available in Black Delrin (D), standard, previously standard: plastic or stainlesssteel(S). as shown on next page. Other materials may be available by special order.
USES: Assists in avoiding accidental disconnection. The long locking sleeves are used to minimize flexing stress beingapplied to the electrical conductor terminations when the cable is flexed.
FEMALE LOCKING SLEEVEFEMALE LOCKING SLEEVEFEMALE LOCKING SLEEVEFEMALE LOCKING SLEEVEFEMALE LOCKING SLEEVE(Long)For use with straight connectors only.This long type of locking sleeve helpsto eliminate conductor breakage attermination joint by eliminating flexingat joint area.
RUBBER MOLDED CONNECTORRUBBER MOLDED CONNECTORRUBBER MOLDED CONNECTORRUBBER MOLDED CONNECTORRUBBER MOLDED CONNECTOR
BULKHEAD CONNECTORSBULKHEAD CONNECTORSBULKHEAD CONNECTORSBULKHEAD CONNECTORSBULKHEAD CONNECTORS
CABLECABLECABLECABLECABLEOr solid rubber for dummy
RUBBER MOLDED CONNECTORRUBBER MOLDED CONNECTORRUBBER MOLDED CONNECTORRUBBER MOLDED CONNECTORRUBBER MOLDED CONNECTOR
RIGHT ANGLE CONNECTORRIGHT ANGLE CONNECTORRIGHT ANGLE CONNECTORRIGHT ANGLE CONNECTORRIGHT ANGLE CONNECTOR
FEMALE LOCKING SLEEVEFEMALE LOCKING SLEEVEFEMALE LOCKING SLEEVEFEMALE LOCKING SLEEVEFEMALE LOCKING SLEEVEThis type of locking sleeve can beused with straight or right angleconnectors.
MALE LOCKING SLEEVEMALE LOCKING SLEEVEMALE LOCKING SLEEVEMALE LOCKING SLEEVEMALE LOCKING SLEEVE
RUBBER MOLDED CONNECTORRUBBER MOLDED CONNECTORRUBBER MOLDED CONNECTORRUBBER MOLDED CONNECTORRUBBER MOLDED CONNECTOR
Notes: Cable diameter must be specified when ordering (long -X) Locking Sleeves.X Size only uses 1/2 inch cable or smaller.
50-32 (REV 0704)
SE
A C
ON
SE
A C
ON
SE
A C
ON
SE
A C
ON
SE
A C
ON
1.70
1.70
2.80 *
1.30
2.90 *
1.80
3.60 *
1.50 ∅
1.50 ∅
1.00 ∅
1.00 ∅
0.80 ∅
0.80 ∅
0.60 ∅
.60
1.00
1.48
.40
.40
.70
.70
LOCKING SLEEVES
Notes: * VSF-FLS-D, G-FLS-X, K-FLS-X length will vary, depending on cable diameter.
A-FLS-D A-MLS-D
F-FLS-D F-MLS-D
VSF-FLS-D VSF-MLS-D
G-FLS-D G-MLS-DG-FLS-S G-MLS-S
G-FLS-X G-MLS-D
K-FLS-D K-MLS-DK-FLS-S K-MLS-S
K-FLS-X K-MLS-D
50-33 (REV 0704)
RUBBER MOLDEDQUICK REFERENCE MATING TABLE
FEMALE SOCKET MATEABLE MALE MATEABLE MATEABLE GLASS REINFORCED IN-LINE PLUG INLINE METAL SHELL EPOXY
BULKHEAD BULKHEAD
RMA-FS RMA-MP RMA-BCL XSA-BC, XSA-BCLRMA-FS R/A RMA-MP SL XSB-BCLRMA-FS SL XSC-BC, XSC-BCL
VMA-FS VMA-MP VMA-BCL VSA-BC, VSA-BCLVMA-FS R/A VSB-BCLVMA-FS SL VMA-MP SL
RMF-FS RMF-MP Not Available At XSF-BC, XSF-BCLRMF-FS R/A This Printing XSFDE-BCL (Formerly XSDE-BCL)
VMF-FS VMF-MP VMF-BCL VSF-BCLVMF-FS R/A
LMG-FS LMG-MP Not Available LSG-BC, LSG-BCLLMG-FS R/A This Printing LSG-BC HP
LSG-BC-SC (Formerly LSK-BC SC)
RMG-FS RMG-MP RMG-BCL XSG-BCL, XSG-BCL-P- R/ARMG-FS R/A RMGS-BC XSG-PBC, XSG-PBCL, XSG-PBCLMRMG-FS WOC RMG-MP WOC RMGS-BCL
VMG-FS VMG-MP VMG-BCL VSG-BCLVMG-FS R/A VSG-PBC, VSG-PBCL, VSG-PBCLMVMG-FS WOC VMG-MP WOC
RMK-FS RMK-MP RMK-BCL XSK-BCLRMK-FS R/A XSKDE-BCLRMK-FS WOC RMK-MP WOC
VMK-FS VMK-MP VMK-BCL VSK-BCLVMK-FS R/AVMK-FS WOC VMK-MP WOC
SPECIAL ASSEMBLIESpb^`lk maintains all facilities necessary to furnish complete under-water and environmental electrical connector/cable systems, includingResearch and Development, Engineering, Manufacturing, QualityControl and Pressure Testing. As well as supplying our standard ‘off-the-shelf’ items, we have the capability to design and manufactureSPECIAL CUSTOMIZED CONNECTORS AND CABLE ASSEMBLIESto suit your individual needs.
All reasonable efforts have been taken to ensure that the information contained herein isaccurate at the date of publication, but no representation or warranty as to the accuracy orcompleteness of such information is intended or to be implied by its inclusion herein. Any andall representations and warranties pertaining to the information and products referred toherein shall be set forth in pb^`lk standard sales order form. In addition, pb^`lkreserves the right to make changes to the contents hereof without notice, therefore it issuggested that at the time of inquiry, the appropriate sales office or factory be contacteddirectly for verification of published specifications and products availability.
© 2015 pb^`lkALL RIGHTS RESERVED
pb^`lk1700 Gillespie Way,El Cajon, California 92020, USA.TEL: +1 (619) 562-7071FAX: +1 (619) 562-9706E-Mail: [email protected]: www.seaconworldwide.com
pb^`lk US GULF AREA SALES OFFICE14511 Old Katy Road, Suite 300,Houston, Texas 77079, USA. TEL: +1 (281) 599-3509FAX: +1 (281) 599-3517E-Mail: [email protected]: www.seaconworldwide.com
pb^`lk US EAST COAST SALES OFFICE15 Gray Lane, Suite 108, Hopkinton Industrial Park,Ashaway, Rhode Island 02804, USA.TEL: +1 (401) 637-4952FAX: +1 (401) 637-4953E-Mail: [email protected]: www.seaconworldwide.com
pb^`lk ADVANCED PRODUCTS, LLC1321 Nelius Road, P.O. Box 767,Bellville, Texas 77418, USA.TEL: +1 (979) 865-8846FAX: +1 (979) 865-8859E-Mail: [email protected]: www.seacon-ap.com
pb^`lk BRAZILRua Conde de Bonfim 120 sala 212, Tijuca,Rio de Janeiro, Brazil, CEP: 20520-053.TEL #1: +55 (21) 3592-0920TEL #2: +55 (21) 3594-0920CELL: +55 (21) 98849-3336E-Mail: [email protected]: www.seaconworldwide.com
pb^`lk (europe) LTDSeacon House, Hewett Road, Gapton Hall Industrial Estate,Great Yarmouth, Norfolk, NR31 0RB, UK.TEL: +44 (0) 1493-652733FAX: +44 (0) 1493-652840E-Mail: [email protected]: www.seaconeurope.com
pb^`lk GLOBAL PRODUCTIONCallejon Terrazos #8, Local 2-C, Las Brisas 1ra. Seccion,Tijuana, B.C., Mexico C.P. 22610.TEL: +52 (664) 626-2726FAX: +52 (664) 686-8922E-Mail: [email protected]: www.seaconglobal.comDial from U.S.A. TEL: +1 (619) 308-7901TOLL FREE: (888) 562-7072FAX: +1 (619) 308-7900
pb^`lk PHOENIX15 Gray Lane, Suite 108, Hopkinton Industrial Park,Ashaway, Rhode Island 02804, USA.TEL: +1 (401) 637-4952 FAX: +1 (401) 637-4953E-Mail: [email protected]: www.seaconphoenix.com
REV II