rts latch top pull magnet latch bottom bracket latch striker€¦ · striker latch top bracket...
TRANSCRIPT
Mount Top Bracket high on the Fence post.
20/09/16
Check the gap between gate and fence post is between 13-38mm.
Slide the Latch over Top Bracket.
Measure Pull Knob is at 1500 high*.
Slide Bottom Bracket onto Latch and mark its position on Fence post.
Remove Latch and mount Bottom Bracket.
Max. 280mm
LATCH
STRIKER
TOP BRACKET
BOTTOM BRACKET
FIG. 6
12/10/12
BY: AM
<< 1500 high
CENT
ERLIN
EOF
LATC
H
3/4"
SPIND
LETH
RUHO
LEGA
TE
FRAM
E
3/4"
FIG. 1
Spind
le
12mm
Sc
rew30
mm
Screw
Cut 11
-13mm
Long
er tha
n Gate
Post
Spind
le Tub
e MU
ST be
fitted
Spind
le Tub
e to be
11
to 13m
m lon
gertha
n Gate
Post
Spind
le
INSIDE
LATC
H
OUTS
IDELA
TCH
The Latch
Striker
Latch
Top Bracket
Bottom Bracket
Pull Knob
Top Bracket
Max. 280mm
LATCH
STRIKER
TOP BRACKET
BOTTOM BRACKET
FIG. 6
12/10/12
BY: AM
CENTERLINE OF LATCH
3/4" SPINDLE THRU HOLE
GATE FRAME
3/4"FIG. 1
Spindle
12mm Screw30mm Screw
Cut 11-13mmLonger than Gate Post
Spindle Tube MUST be fitted
Spindle Tube to be
11 to 13mm longerthan Gate Post
Spindle
INSIDE LATCH
OUTSIDE LATCH
CENT
ERLIN
EOF
LATC
H
3/4"
SPIND
LETH
RUHO
LEGA
TE
FRAM
E
3/4"
FIG. 1
Spind
le
12mm
Sc
rew30
mm
Screw
Cut 11
-13mm
Long
er tha
n Gate
Post
Spind
le Tub
e MU
ST be
fitted
Spind
le Tub
e to be
11
to 13m
m lon
gertha
n Gate
Post
Spind
le
INSIDE
LATC
H
OUTS
IDELA
TCH
STARTGate Fence
*Check the pool fencing regulations and safety standards relevant to your state or territory.
DPL1000MK3
TOP PULLMAGNET LATCH
DPL1000MK3
TOP PULLMAGNET LATCH
LATCH PARTS
Use Striker Adjuster to move Striker side-to-side to align the Striker to Latch.
FIG. 9
FIG. 7FIG. 6
FIG. 10
STEP 5: Install Keeper Assembly
Adjust Keeper assembly (Fig. 11) to align with 1.
adjustment has been reached when the line on the Keeper assembly reaches the gate face. (Fig. 10)
2.between the two marks on the Latch Body
mark.
Secure Keeper Assembly to Gate in this 3.
in (Fig. 8).
Open gate and using a screwdriver, adjust the keeper assembly out to expose the remaining two
screws then return Keeper Assembly back to proper alignment (Fig.6).
4.
STEP 6: Final Adjustments
1.Adjustments are needed, use the Horizontal Adjustment screw located in the Keeper
Adjustment holes located in the Lower Bracket (Fig. 12).
Max. 280mm
LATCH
STRIKER
TOP BRACKET
BOTTOM BRACKET
FIG. 6
12/10/12
BY: AM
CENT
ERLIN
EOF
LATC
H
3/4"
SPIND
LETH
RUHO
LEGA
TE
FRAM
E
3/4"
FIG. 1
Spind
le
12mm
Sc
rew30
mm
Screw
Cut 11
-13mm
Long
er tha
n Gate
Post
Spind
le Tub
e MU
ST be
fitted
Spind
le Tub
e to be
11
to 13m
m lon
gertha
n Gate
Post
Spind
le
INSIDE
LATC
H
OUTS
IDELA
TCH
Slide Latch over both brackets. Set Pull Knob height at 1500*
Lock in place with small countersunk screw.
The Striker Place Striker onto Latch.
Close gate & mark above & below Striker to set mount position.
Max. 280mm
LATCH
STRIKER
TOP BRACKET
BOTTOM BRACKET
FIG. 6
12/10/12
BY: AM
Secure Striker to gate using X holes.
Using Striker Adjuster expose Z holes. Mount Striker using the Z holes.
Z
X
X
Fine Tune
Adjust up/down by removing small countersunk screw and slide Latch.
If Striker adjusts past this point the gate/fence gap is too great.
Check alignment marks on Striker sits within the two on Latch.
STRIKERCENTERLINE OF LATCH
3/4" SPINDLETHRU
HOLEGATE FRAME
3/4"FIG. 1
Spindle
12mm Screw30mm
Screw
Cut 11-13mm Longer than Gate Post
Spindle Tube MUST be fitted
Spindle Tube to be 11 to 13mm longer than Gate Post
Spindle
INSIDELATCH
OUTSIDE LATCH
CENT
ERLIN
EOF
LATC
H3/4"
SPIND
LETH
RUHO
LE
GATE
FR
AME
3/4"
FIG. 1
Spind
le
12mm
Sc
rew30
mm
Screw
Cut 11
-13mm
Long
er tha
n Gate
Post
Spind
le Tub
e MU
ST be
fitted
Sp
indle T
ube to
be
11 to
13mm l
onger
than G
ate Po
st
Spind
le
INSIDE
LATC
H
OUTS
IDELA
TCH
CENT
ERLIN
EOF
LATC
H
3/4"
SPIND
LETH
RUHO
LEGA
TE
FRAM
E
3/4"
FIG. 1
Spind
le
12mm
Sc
rew30
mm
Screw
Cut 11
-13mm
Long
er tha
n Gate
Post
Spind
le Tub
e MU
ST be
fitted
Spind
le Tub
e to be
11
to 13m
m lon
gertha
n Gate
Post
Spind
le
INSIDE
LATC
H
OUTS
IDELA
TCH
CENT
ERLIN
EOF
LATC
H
3/4"
SPIND
LETH
RUHO
LEGA
TE
FRAM
E
3/4"
FIG. 1
Spind
le
12mm
Sc
rew30
mm
Screw
Cut 11
-13mm
Long
er tha
n Gate
Post
Spind
le Tub
e MU
ST be
fitted
Spind
le Tub
e to be
11
to 13m
m lon
gertha
n Gate
Post
Spind
le
INSIDE
LATC
H
OUTS
IDELA
TCH
CENTERLINE OF LATCH
3/4" SPINDLETHRU
HOLEGATE FRAME
3/4"FIG. 1
Spindle
12mm Screw30mm
Screw
Cut 11-13mm Longer than Gate Post
Spindle Tube MUST be fitted
Spindle Tube to be 11 to 13mm longer than Gate Post
Spindle
INSIDELATCH
OUTSIDE LATCH
*Check the pool fencing regulations and safety standards relevant to your state or territory.
Continued
IMPORTANT: Use a screwdriver not a power toolto adjust Striker.
30
74
100 85
510
72
50 79
25
100
66
Note: Swimming pool gates, fences and their hardware systems are designed to aid and not substi tute for adult supervision. To the extent this product is used around a pool, prior to installing, consult local licensing and safety authoriti es for approvals and/or requirements. The TRIDENT™ will operate properly only if installed in accordance with instructi ons.
Maintenance: The TRIDENT™ latches should be inspected annually, or more frequently if the gate is used oft en. Use a non-toxic lubricant on all moving parts. Use mild soap & water to clean exterior body or unit. Always remove key upon locking. Occasion-ally re-ti ghten all mounti ng screws to assure proper operati ons. Please make sure product is adjusted properly per originally supplied instructi ons.
WARRANTYMANUFACTURER’S
NATIONWIDE INDUSTRIES Tampa, Florida 33619 USA
TRIDENT™ Series Latches
What Does This Warranty Cover? This warranty covers materials and workman-ship as well as any loss of functi onality in your new TRIDENT™, with the excepti ons stated below.
What Will Nati onwide Do? In the event of any defect in material or workmanship or loss of functi onality in the product covered under this warranty, Nati onwide will replace such TRIDENT ™with a new TRIDENT™ (or, in the event the TRIDENT™ is no longer available, a latch similar thereto) at no charge.
How Does State Law Apply? This warranty gives you specifi c legal rights, and you may also have other rights which vary from state to state.
How Long Does the Coverage Last? This warranty to the original purchaser (end user) runs for the durati on of one million cycles of use. Nati onwide Industries assumes this is a true lifeti me of use on residenti al applicati ons, and for commercial applicati ons will use an esti mate of usage based on each applicati on.
How Do You Get Service? In the event of any defect in material or workmanship, or failure in the TRIDENT™ covered under this warranty, please return the TRIDENT™ postage paid, together with proof of purchase and a brief writt en descripti on of the problem to Nati onwide Industries, 10333 Windhorst Road, Tampa, Florida 33619, Att enti on: Customer Service Manager.
What Does This Warranty Not Cover? This warranty is void in its enti rety in the event the TRIDENT™ is tampered with, altered, misused, neglected, damaged, improperly installed or maintained, repaired or att empted to be repaired by an unauthorized person, or used in any manner which is not in accordance with the instructi ons provided by Nati onwide. Nati onwide’s aggregate liability in damages or otherwise shall not exceed the payment, if any, received by Nati onwide for the TRIDENT™ furnished to you which is the subject of a claim or dispute. In no event shall Nati onwide be liable, whether in contract, in tort, under warranty, in negligence or otherwise for incidental, consequenti al, or special damages of any kind whatsoever, howsoever caused.
DISCLAIMER: A pool owner or operator is always responsible for the safety of those in or around the pool and, to the extent this product is used around a pool, the manufacturer and supplier of this device cannot and will not accept such responsibility. In additi on, the manufacturer and supplier of this device cannot and will not accept responsibility for unauthorized modifi cati ons to or for defecti ve or inadequate maintenance of this device. No modifi cati on to this device whatsoever is to be made other than with respect to the adjustments outlined in the installati on instructi ons. If this device fails to functi on properly, it should be returned promptly to the supplier for replacement.
Eff ecti ve for products sold aft er 1/1/15.
Million Cycle Warranty and Liability Limitation