FITMENT INSTRUCTIONSISUZU DOUBLE CABISUZU EXTENDED CAB

LIKE SHARE FOLLOW

PLEASE ENSURE TO READ FITMENT INSTRUCTIONS CAREFULLY

BEFORE ATTEMPTING TO INSTALL.

1

BOLT

S

Foam Strip

DESCRIPTION QTY EXAMPLE

1

4

WAS

HERS M8 X 20 Flat Washers 4

M8 Spring Washer 4

FITMENT KIT CONTENT (HARDWARE)

FITMENT KIT CONTENTS

CATEGORY TOOLS EXAMPLE

TOOL

S

Socket Wrench & Accessories

Flat Spanners

REQUIRED TOOLS

Allen Keys

NO. 17 SocketNO. 13 SocketSocket Wrench

NO. 17 FLATNO. 13 FLAT

FULL SET

Torx Keys FULL SET

Set Screw M8 x 30

FOAM

Torque Wrench

Mounting Clamps 4

CLAM

PS

M8 Stainless Steel Weldnuts 8

FITMENT OF THE RSI SMARTCANOPY TO VEHICLE

PLEASE ADHERE TO BELOW TO PREVENT DAMAGE TO VEHICLE AND RSI SMARTCANOPY DURING FITMENT

WARNING

!1. ONLY USE THE RECOMMENDED TOOLS AS INDICATED IN THE FITMENT INSTRUCTION ABOVE2. ONLY USE THE HARDWARE PROVIDED IN THE FITMENT KIT OUTLINED ON THE PAGE BEFORE3. HANDLE ALL RSI SMARTCANOPY FITMENT COMPONENTS WITH CARE UPON UNPACKING.4. IT IS RECOMMENDED THAT THE MINIMUM OF FOUR PEOPLE ARE USED TO LIFT THE RSI SMARTCANOPY.5. NEVER USE ACETONE ON PAINTWORK

STEPONESTEPTWO

1. UNPACK ALL COMPONENTS & THE HARDWARE KIT FROM PACKAGING; ENSURE THAT EVERYTHING IS ACCOUNTED FOR AS INDICATED ON PAGE BEFORE2. WHEN UNPACKING COMPONENTS, PLEASE PLACE THEM ON A PROTECTED SURFACE (E.G. FOAM) TO ENSURE THAT THE PAINT IS NOT DAMAGED OR SCRATCHED

1. REMOVE ANY CAB GUARD, ROLL BAR, TONNEAU COVER ETC.2. REMOVE THE SPECIFIED TORX SCREWS.

STEPTHREE

1. APPLY 5MM FOAM STRIP ALONG TOP SURFACE OF FRONT LIP OF LOAD BIN

5mm Foam Strip

2

3

FITMENT OF THE RSI SMARTCANOPY TO VEHICLE

STEPFOUR

1. POSITION THE RSI SMARTCANOPY ONTO THE LOAD BIN AND LINE UP THE HOLES.2. PLACE 2 CLAMPS LIKE DEPICTED BELOW.3. FASTEN THE MOUNTING CLAMP TO 25NM.4. REPEAT THIS PROCESS ON THE OPPOSITE SIDE OF THE LOAD BIN.

STEPFIVE

1. USE TWO M8 X 30 SET SCREWS WITH M8 SPRING WASHERS AND M8 X 25 FLAT WASHERS TO LOOSELY SCREW THE RSI SMARTCANOPY TO THE REAR OF THE LOAD BIN.2. REPEAT THIS PROCESS ON THE RIGHT HAND SIDE OF THE LOAD BIN.3. ONCE ALL THE FASTENERS ARE IN POSITION FASTEN ALL THE SET SCREWS TO 25NM.

427150

Mounting Clamp Mounting Clamp

M8 X 30 Set Screws

M8 Spring Washer

M8 X 25 Flat Washer

RSISMARTCANOPY SMARTCANOPYDBN 031 700 5925 CPT 021 981 2301JHB 011 974 0370

THANK YOU FOR PURCHASING A RSI SMARTCANOPY. SHOULD YOU HAVE ANY ENQUIRIES ABOUT THE FITMENT, FEEL FREE TO CONTACT US

4

FITMENT OF THE RSI SMARTCANOPY

STEPSIX 1. SLIDE M8 WELDNUTS INTO THE ROOF RAILS.

2. BOLT ROOF MOUNTED ACCESSORIES TO THE WELDNUT CLAMPING THE ACCESSORIES DOWN.

ONLY REQUIRED WHEN FITTING ROOF MOUNTED ACCESSORIES

M8 WELDNUTS SLIDE INTO ROOF RAILS WHEN BOLTING DOWN ROOF MOUNTED ACCESSORIES.