royal z bar couplers -...
TRANSCRIPT
26
WA
LL &
CO
LU
MN
TIE
S: R
OYA
L Z
BA
R S
YS
TEM
ROYAL Z BAR
The ROYAL Z Bar is a high tensile steel Dywidag threaded rod system used to tie wall forms together. It has a coarse, rounded thread for speed of use and easy cleaning. The Z bar’s nominal diameters are 15/17mm and it is available as either hot or cold rolled. Z bars are used with large wing nuts, washer plates, spacer tubes and cones making them completely removable and reusable.
Description Weight (kg) Code NumberZ Bar 1.5m Hot Rolled 2.16 ZB15HR
Z Bar 3.0m Hot Rolled 4.32 ZB3HR
Z Bar 6.0m Hot Rolled 8.64 ZB6HR
Also available in 20mm and 26.5mm diameter.
ROYAL Z BAR COUPLERS
Weldable 15mm Z Bar hexagon Couplers create a full-strength, mechanical joint between two Dywidag threaded Z Bars, replacing the need for additional full length bars.
Description Weight (kg) Code NumberZ Bar Coupler 50mm 0.30 ZBJ50
Z Bar Coupler 100mm 0.41 ZBJ100
ROYAL Z BAR WING NUTS
The ROYAL Z Bar cast iron wing nut is used in the formation of walls. They are designed to spin freely on the high speed course Dywidag thread by hand and may be tightened using the length of a hammer. They are available with either a single or double arm. The single arm provides resistance to movement during vibration whereas the balanced double arms make it easier to turn when fitting and removing.
Description Weight (kg) Code Number
Z Bar Wing Nut Single Arm 0.25 ZBWNS
Z Bar Wing Nut Double Arm 0.32 ZBWND
Also available to suit: 20mm and 26.5mm diameter Z bars.
ROYAL Z BAR ROCK ANCHOR EXPANSION SHELL
The Z Bar Tie Anchor Expansion Shell is used for single-sided formwork shutters or for temporary tie-downs into concrete. The anchor has a shell length of 105mm which is inserted into a 32mm diameter hole. A 15/17mm Z bar is screwed tightly into the anchor shell until fully expanded. It is thread tested for a MWL 90kN. NB. Client is to obtain Engineer’s advice to determine anchor depth and pull-out load.
Description Weight (kg) Code Number
Z Bar Concrete Anchor 105mm 0.20 ZBCA105
STEEL WASHER PLATE
The Steel Washer Plate is used to evenly distribute the load over form supports. It has an 18.5mm diameter hole in its centre for a coil tie bolt or Z bar to feed through and two (2) smaller holes to securely nail the washer to timber soldiers.
Description Weight (kg) Code NumberWasher 120x120x6mm Embossed 0.60 WASH120EMB
Washer 125x100x8mm 0.72 WASH125
Washer 150x150x10mm 2.00 WASH150
VERTICAL ELEMENTS FORMWORK SOLUTIONS
WA
LL &
CO
LU
MN
TIE
S: R
OYA
L Z
BA
R S
YS
TEM
27
ROYAL CONDUIT
The ROYAL Conduit is a plastic spacer tube through which the Z bar feeds. Grout is prevented from entering the tube, allowing the Z bar to be easily removed when stripping the forms. They are supplied in full lengths and are cut down to the wall’s thickness and a cone is attached on each end. Tubes have an O.D of either 25mm or 27mm. The 25mm tube uses the plastic push in-and-fit cones whereas the cone fits on the outside of the larger 27mm tube.
Description Code Number
Z Bar Conduit 25mm 2.9m ZBCON29M
Z Bar Conduit 27mm 2.9m ZBCON29M27
Z Bar Conduit 25mm 4.0m ZBCOND2540
Z Bar Conduit 27mm 4.0m ZBCOND2740
ROYAL PVC Z BAR CONES
The ROYAL Z Bar PVC Cones are manufactured from a high grade, durable plastic and are fitted at the ends of tubes to the correct wall thickness to prevent slurry filling up. Once the forms are removed the cones are exposed and removed using a cone remover tool.
Description Code Number
Z Bar Conduit 25mm Cone (Internal conduit fitting) ZBC25
Z Bar Conduit 25mm Cone Flanged (Internal conduit fitting) ZBC25F
Z Bar Conduit 27mm Cone Flanged (External conduit fitting) ZBC27F
CONCRETE PLUGS FOR Z BAR CONES HOLES
These pre-made Concrete Plugs are slipped into the recess left by the cone once removed from the concrete wall. Available in concrete colour and commonly used as a flush or recessed architectural finish on concrete feature walls, or simply to fill the recessed hole without fuss or mess.
Description Code Number
Concrete Plug Z Bar Grey Recess ZBCP25
Concrete Plug Z Bar Grey Flange ZBCP25F
28
VER
TIC
AL E
LEM
EN
TS F
OR
MW
OR
K S
OLU
TIO
NS – W
ALL &
CO
LU
MN
TIE
S
COIL TIE SPRINGS
2 BAR STANDARD COIL TIE SPRINGS
Two (2) bars are welded to the coil tie springs which screw onto removable plastic cones to set the desirable width of the concrete wall to be formed. Coil tie bolts are screwed on either end to secure the wall shutters together. On completion, the coil tie cones are removed, leaving a neat hole in the concrete’s face.
4 BAR HEAVY DUTY COIL TIE SPRINGS
Four (4) bars are welded to coils giving greater strength than the two (2) bar springs. They are used to space coil ties in the concrete further apart, to use fewer coil ties in a wall and are ideal for matching an architectural pattern on the finished wall. Four (4) bar coil tie springs allow coil ties to be used as an architectural feature.
Coil Tie springs remain buried in the concrete, creating an effective water barrier.
Tie size for 25mm Cones (wall thickness)
2 Bar 4 Bar
Weight (kg) Code No Weight (kg) Code No
Coil Tie Spring 150mm 0.11 CTS150 0.14 CTS1504
Coil Tie Spring 175mm 0.12 CTS175 0.18 CTS1754
Coil Tie Spring 200mm 0.13 CTS200 0.19 CTS2004
Coil Tie Spring 225mm 0.14 CTS225 0.20 CTS2254
Coil Tie Spring 250mm 0.15 CTS250 0.22 CTS2504
Coil Tie Spring 275mm 0.16 CTS275 0.24 CTS2754
Coil Tie Spring 300mm 0.17 CTS300 0.26 CTS3004
Coil Tie Spring 325mm 0.18 CTS325 0.28 CTS3254
Coil Tie Spring 350mm 0.19 CTS350 0.30 CTS3504
Coil Tie Spring 375mm 0.20 CTS375 0.32 CTS3754
Coil Tie Spring 400mm 0.21 CTS400 0.34 CTS4004
Coil Tie Spring 425mm 0.22 CTS425 0.36 CTS4254
Coil Tie Spring 450mm 0.23 CTS450 0.38 CTS4504
Coil Tie Spring 475mm 0.24 CTS475 0.40 CTS4754
Coil Tie Spring 500mm 0.25 CTS500 0.41 CTS5004
Coil Tie Spring 525mm 0.26 CTS525 0.43 CTS5254
Coil Tie Spring 550mm 0.27 CTS550 0.45 CTS5504
Coil Tie Spring 575mm 0.27 CTS575 0.47 CTS5754
Coil Tie Spring 600mm 0.28 CTS600 0.49 CTS6004
Coil Tie Spring 625mm 0.29 CTS625 0.51 CTS6254
Coil Tie Spring 650mm 0.30 CTS650 0.53 CTS6504
Coil Tie Spring 700mm 0.32 CTS700 0.56 CTS7004
Coil Tie Spring 725mm 0.33 CTS725 0.58 CTS7204
Coil Tie Spring 750mm 0.34 CTS750 0.60 CTS7504
Coil Tie Spring 800mm 0.36 CTS800 0.64 CTS8004
Coil Tie Spring 850mm 0.38 CTS850 0.67 CTS8504
Coil Tie Spring 900mm 0.40 CTS900 0.71 CTS9004
Coil Tie Spring 950mm 0.42 CTS950 0.75 CTS9504
Coil Tie Spring 1000mm 0.43 CTS1000 0.79 CTS10004
ROYAL COIL TIE WALL SYSTEM
29
VER
TIC
AL E
LEM
EN
TS F
OR
MW
OR
K S
OLU
TIO
NS – W
ALL &
CO
LU
MN
TIE
S
COIL TIE BOLTS
Strong, course, threaded bolts, with hexagonal head for positive contact can be fixed easily and quickly. They are used with steel washer plates and screwed into coil springs to secure forms together. They are made from high tensile steel for exceptional strength. Various sizes are available from 100mm to 500mm.
Description Code NumberCoil Tie Bolt 100mm CTB100
Coil Tie Bolt 135mm CTB135
Coil Tie Bolt 150mm CTB150
Coil Tie Bolt 190mm CTB190
Coil Tie Bolt 235mm CTB235
Coil Tie Bolt 300mm CTB300
Coil Tie Bolt 350mm CTB350
Coil Tie Bolt 400mm CTB400
Coil Tie Bolt 500mm CTB500
Coil Tie Bolt 600mm CTB600
Ratchet Wrench 19mm – 23mm WRENCH
STEEL WASHER PLATE
The Steel Washer Plate is used to evenly distribute the load over form supports. It has an 18.5mm diameter hole in its centre for a coil tie bolt or Z bar to feed through and two (2) smaller holes to securely nail the washer to timber soldiers.
Description Weight (kg) Code Number
Washer 120x120x6mm Embossed 0.60 WASH120EMB
Washer 125x100x8mm 0.72 WASH125
Washer 150x150x10mm 2.00 WASH150
COIL TIE THREADED ROD
The Coil Tie Threaded Rod has an identical thread and load capacity as the coil tie bolt (with a 12.5mm diameter). It screws into the coil tie spring to create an extension of various lengths between coil tie springs. It may also be anchored into rock or other existing structure and used with a coil tie spring for a single sided form application.
Description Code NumberCoil Tie Spring Thread Rod 3000mm CTSTHR3
Coil Tie Spring Thread Rod Cast Wing Nut CTSTHRWNC
Coil Tie Spring Thread Rod Wing Nut CTSTHRWN
PLASTIC COIL TIE CONES
These removable PVC cones are threaded onto the coil tie spring to complete the tie and seal the hole to prevent concrete leakage. The cone also acts as a spacer of the concrete’s wall thickness. The cones are easily removed from the recessed hexagonal form with ROYAL’s cone removal spanner and are suitable for multiple reuse.
Description Code NumberCoil Tie Spring Cone 13mm CTSC13
Coil Tie Spring Cone 25mm CTSC25
Coil Tie Spring Cone 37mm CTSC37
Coil Tie Spring Cone 50mm CTSC50
CONE REMOVAL KEY
Once concrete forms are removed, cone keys are used to remove the cones from the concrete without damaging either the concrete or the cone. Two (2) types of cone key spanners are available:
1. The cone bolt spanner is designed to tighten and release the coil tie bolt in the form while the opposite side provides the hexagonal key to turn and remove the cone;
2. The cone bolt spanner combo removes three (3) types of cones – the coil tie spring cone, the standard Z bar cone and the larger Z bar cone.
Description Code Number
Cone Bolt Spanner CBS
Cone Bolt Spanner Combo CBSC
30
VER
TIC
AL E
LEM
EN
TS F
OR
MW
OR
K S
OLU
TIO
NS – W
ALL &
CO
LU
MN
TIE
S
CONCRETE PLUGS FOR COIL TIE CONE HOLES
Pre-made concrete plugs are used to slip into the recessed cone removed from the completed concrete wall. Available in concrete colour, finishing flush or recessed in the hole. They are commonly used as an architectural flourish on concrete feature walls or alternatively used as a faster and simpler method to fill in the recessed cone holes without mess.
Description Code NumberConcrete Plug - Coil Tie Grey Flush CTSCPGF
Concrete Plug - Coil Tie Grey Recessed CTSCPGR
Concrete Plug - Coil Tie Off White Flush CTSCPOWF
ROYAL COLUMN CLAMPS
ROYAL Column Clamps are used in the construction of square and rectangular concrete columns. The flat bars have cupped ends and staggered slots, providing for extensive adjustment within the range of each clamp. The simple wedge connection provides for quick assembly and stripping. There are three (3) arm lengths to cater for different column sizes.
DescriptionArm Length
(x) (mm)(y)
(mm)(z)
(mm)Weight (kg) Code Number
ROYALcolumn clamp No 1 740 325 75 3.25 RCC1
ROYALcolumn clamp No 2 1030 510 75 4.50 RCC2
ROYALcolumn clamp No 3 1460 765 75 6.50 RCC3
ROYALcolumn clamp Wedge - - - 0.30 RCCW
ROYAL SHUTTERHOOK
ROYALshutterhooks are crane lifting hooks/lugs which attach to formwork timber shutters. Designed and manufactured from steel section with a large round ring for crane hooks to be easily hooked. Each lug is certified for a SWL of 500kg and is easily bolted to timber components to lift formwork shutters in and out of position for safe and high productivity. Independent testing/tagging is required annually and shutter design is by contractor’s engineer. Fits between twin vertical soldiers and has multiple bolt holes located on the square 50mm x 50mm steel section for flexibility to fix on multiple positions.
Description Weight (kg) Code Number
ROYALshutterhook 4.0 RSH