Rose Controls

DepthModulation Intensity

MixAnalog Dry/Wet Mix

RateModulation Speed

ShapeModulation Source

HotswitchTrigger/Toggle Hotswitch function

Select preset in Preset mode

Active/BypassActive+Hotswitch = Enter Preset Mode

Load Preset in Preset Mode

Feedback Analog Feedback to the Delay LineWarning: Due to Rose’s analog signal path and

multi-dimensional controls, feedback can go crazy

Hotswitch LEDActive LED

Red – Preset ActiveGreen – Preset Modified

Filter Analog Low Pass Filter

Delay Multiplier On/Off

Comb Delay – Flip Phase

Long Delays – Reverse Delay

Preset Press – Select PresetHold – Save PresetLit – Preset Loaded

Preset Ladder

DelayTurn – Fine Delay

Push and Turn – Coarse Delay

Shape Ladder

Input Output Expression Pedal Jack

I/O Level

Power Supply9VDC (4.5W)

USB MIDI/Software Updates

Rear and Side Panels

Presets Delay Range IndicatorThe Preset is modified when the ACTIVE LED is green.

Load Preset Use Preset Button to select Preset OR: - Press both footswitches. - Press HOTSWITCH repeatedly to select. - Press ACTIVE to load preset. - Press both footswitches to abort without loading.

Save Preset - Press+Hold PRESET button: the current preset will flash. - Press PRESET button to select target preset slot. - Press+Hold PRESET until LED flashes quickly. - Preset is now saved in selected slot.

- When delay is adjusted, the Preset LED Ladder indicates the delay range.

- Push and turn the Delay Knob to select one of ten delay ranges.

- Turn the Delay Knob (w/o pushing) to fine tune delay within delay range.

COMB MIN milliseconds seconds MAX

TAP*

HOLD MOD

RESET MOD

A/B

CLICK

Set Hotswitch Function

*Tap - Delay or LFO

Set Bypass ModeHOLD

EXIT

BUFFER

RELAY

INPUT KILL

HOLD

CLICK

EXIT

(Delay Multiply)

2x

3x

4x

5x

HOLD

CLICK

EXIT

EXP

MOD/CV

MIDI

Set Exp Pdl JackHOLD

CLICK

EXIT

All Off = Aux SwitchesFactory Default = EXPThis is a Global Setting

Factory Default = Buffered

This is a Global Setting

Hotswitch = Tap Tempo

HOLD TO TOGGLE

Set MIDI Channel/CCHOLD

CLICK CLICK

EXIT1 2 3 4 5... 16

Set MIDI Channel (default=1): Click Shape

Set MIDI Expression CC (default=7): Click

This is a Global Setting

INFINITE REPEAT

Pause ModulationHotswitch = Hold

Restart Modulation/LFOHotswitch = RESET

Delay LFO

EXP PDL JACKExpression Pedal, Auxiliary Switches, MIDI, Mod/CV

Triple Auxiliary Switch Assignment- Up to 3 momentary aux switches via Tip, Ring and Tip+Ring. - Aux switches can be set to control: Tap Tempo, Infinite Repeat, Mod Hold, Mod Reset, Alt A/B, , , and Preset Load/Increment/Decrement. - Aux Switch assignments are Global.

Mod/CV - Control Voltage Range = 0-3.3V. Input impedance = 10k ohm

MIDI Over TRS Requires a TTL-MIDI adapter box. Set Tip to receive. See eventideaudio.com/rose for more information on MIDI programming.

USING ALTERNATE SETTINGS: ALT A/BEach preset contains an A/B pair of settings. You can use the Hotswitch or Aux Switch (or MIDI CC#27) to toggle between A&B OR morph using an Expression Pedal. The A/B settings cover all knobs, , and Shape buttons.

Tip: When creating a new preset, you can copy all A settings to B by pressing and holding and . Tip: Hold down while turning knobs to adjust A & B settings simultaneously.

Using Expression Pedal to Morph Between A/BExpression pedal morphs between A/B settings.1. Move Expression Pedal to full heel-down position.2. Move knobs as desired. Set , . Select Shape.3. Press and Hold + to copy A to B. 4. Move Expression Pedal to full toe-down position.5. Change one or more knobs. Set , . Select Shape.

Important Notes: 1. Set Exp Pdl Jack to “EXP”. 2. Expression Pedal is disabled whenever a preset is loaded. Rock to enable.3. To autocalibrate, rock full heel to full toe.4. , and Shape change from A to B settings at Expression Pedal mid-point. 5. , and ALT A/B are overridden by the Expression Pedal.6. Recommended Expression Pedal impedance: 5k - 25k ohm.

Assigning Exp Pdl Tip/Ring/T+R to Control FunctionTIP

RING

TIP+RING

PRESS DESIRED AUX SWITCH

Cycle through Tap, Inf Rpt, Mod Hold, Mod Rst, A/B, , , Load Preset (Active LED Yellow), Increment Preset (Hotswitch LED Green) and Decrement Preset (Hotswitch LED Red).

Eventide is a trademark of Eventide, Inc. Part #: 141303Version 1.0

Eventide Inc.One Alsan Way

Little Ferry, NJ 07643 USAeventideaudio.com

Technicial Supporteventide.com/support

Restore Factory Settings: Boot pressing HOTSWITCH & Button. Presets will be overwritten.

Software Update: Boot pressing HOTSWITCH & Button.