ronick entrance mat carpet strip replacement instructions...ronick entrance matting 13220 willow...
TRANSCRIPT
Ronick Entrance Matting
13220 Willow Lane Circle · Burnsville, MN 55337 Tel: (952) 895-8811 Toll Free: (877) 242-8821
Fax: (952) 894-0453 www.ronick.com e-mail: [email protected]
1
Ronick Entrance Mat Carpet Strip
Replacement Instructions
Tools Needed: Hammer & Chisel
Flathead Screw Drivers
Utility Knife
Rivet Gun
Optional: Drill or Grinder
Propane Torch
Note: Installation times may vary depending upon condition of your mat.
Ronick Entrance Matting
13220 Willow Lane Circle · Burnsville, MN 55337 Tel: (952) 895-8811 Toll Free: (877) 242-8821
Fax: (952) 894-0453 www.ronick.com e-mail: [email protected]
2
Traffic and weather conditions will determine the longevity of your carpet inserts. Look at the heavy ice melter and dirt build-up forming a "cow path" in the carpet fibers.
Begin by lifting up your Pedigrid and moving them to your work area.
Ronick Entrance Matting
13220 Willow Lane Circle · Burnsville, MN 55337 Tel: (952) 895-8811 Toll Free: (877) 242-8821
Fax: (952) 894-0453 www.ronick.com e-mail: [email protected]
3
Existing carpet inserts are fastened down by rivets. To break rivets use hammer and chisel.
Remove Pedigrid inserts by pulling the strips. In rare cases, inserts may be brittle and break as you pull.
Ronick Entrance Matting
13220 Willow Lane Circle · Burnsville, MN 55337 Tel: (952) 895-8811 Toll Free: (877) 242-8821
Fax: (952) 894-0453 www.ronick.com e-mail: [email protected]
4
After you remove carpet inserts, clear the rails with a chisel to remove accumulated dirt.
Dirt also builds up between rails - clean this area out in order for debris to fall into recess.
Ronick Entrance Matting
13220 Willow Lane Circle · Burnsville, MN 55337 Tel: (952) 895-8811 Toll Free: (877) 242-8821
Fax: (952) 894-0453 www.ronick.com e-mail: [email protected]
5
Another way to clean your Pedigrid - use a steel wire brush on the end of a drill or a grinder.
You are now ready to place new carpet insert material into the cleaned rails. If rail openings are tight, two people may be required to pull insert material through rail.
Ronick Entrance Matting
13220 Willow Lane Circle · Burnsville, MN 55337 Tel: (952) 895-8811 Toll Free: (877) 242-8821
Fax: (952) 894-0453 www.ronick.com e-mail: [email protected]
6
Flip your Pedigrid and drill a hole through the carpet material for placement of a rivet head.
From the top of your Pedigrid, rivet the ends of your new inserts to secure strips.
Ronick Entrance Matting
13220 Willow Lane Circle · Burnsville, MN 55337 Tel: (952) 895-8811 Toll Free: (877) 242-8821
Fax: (952) 894-0453 www.ronick.com e-mail: [email protected]
7
Cut off excess material on the ends with a utility knife.
OPTIONAL: For a professional look, use a propane torch to melt the edges of the carpet insert material to prevent fraying.
Ronick Entrance Matting
13220 Willow Lane Circle · Burnsville, MN 55337 Tel: (952) 895-8811 Toll Free: (877) 242-8821
Fax: (952) 894-0453 www.ronick.com e-mail: [email protected]
8
When reinstalling your Pedigrid, if grid opening is tight, use a flathead screw driver to wedge around the perimeter.
Your Pedigrid will perform and look like new at a fraction of the cost of purchasing new grids.