rolling deck user manulï¼ englishï¼ · 8vh 2i 7kh 5roolqj 'hfn 6wduw xs &dxwlrq 1rwh...
TRANSCRIPT
1
Rolling Deck Manual
2
INDEX
1. Introduction
1.1. General information
1.2. Safety warnings
1.3. Standard roll deck specification
2. Description Of The Installtion Procedure
2.1. General diagram
2.2 .Parts list
3. Installation
3.1. Installation steps
3.2. Decoration materials installation
4. Use Of The Rolling Deck
4.1.Start up
4.2.Caution
4.3.Note
5. Packing Instruction
3
1. INTRODUCTION
1.1. General information
This Rolling deck is ideal design for in ground Spa, Swimspa and Swimming pool. It can be customized in different size. Elegant walk-in terrace. Well insulated and heat lock. Electrically adjustable remote control. Heated rail for winter use Always clean pool water. The deck surface can be tailored to customer requirements. Completely usable as a patio cover. Easy to use, durable, easy care and maintenance
1.2. Safety warnings
This manual may change subject to development without prior notice. 1. The Product must be placed on the horizontal and solid ground. 2. For safe use, the Product should be regularly checked monthly. 3. Power off before installation. 4. The product is heavy; please apply necessary protection during installation. 5. Do not step on and throw hit before all screws and surface board were fixed well. 6, Please protect the Aluminum insulation board correctly.
1.3. Standard Rolling deck specification(Short/ Long side rolling):
Note: Tailored Made rolling deck specification will be provided separate.
Dimension Overall
weight Heated rail Run time
Rated
motor
capacity
Frame and insulation
board QTY
Voltage
Remark
According to the
packing list 1000KG 400W,36V 15S 110W
According to the
packing list 220V 50Hz
4
2. DESCRIPTION OF THE INSTALLATION PROCEDURE
2.1. General diagram
2.2 Parts list
Spare Parts List
1 Aluminum insulation board
2 Aluminum Frame
3 Motor
4 Sealing rubber
5 Rolling wheel (Height adjustable)
6 Motor base
5
3. Installation
3.1. Installation steps.
Step 1. Prepare the tools
A Locking Plier
B Screwdriver
C Voltage tester
D Wrench
7 Racks
8 Stopper
9 Rails
10 Chain Groove
11 Water proof foil insulation sheet
12 Safety infrared detector
13 The reinforcing plate
14 Remote controller
6
E Hex Wrenches
F Ratchet wrench
Step 2. Install the rails and heater
Important installation details guide: Important measures and installation position:
①Distance between Rails and swim spa/spa lip :80mm
②Rail stay longer than the lip 80mm
(L=the length of spa(short side rolling)/ the width of spa(long side rolling))
Details drawing as below:
Screw the rail to the even ground( Self tapping screw: 5*20).
Special remind:First screw the rail on this side, and then fixed on the other side after step 3 to
finish.
Swim
spa/Spa lip
Rail
7
Step 3. Install the wheels to the frame and joint the deck frame. (1). Slid in the square female screw to the reserved wheel position and fixed the wheels.
Important note: The deck height can be adjusted by the wheel Hexagon screw, The
Spa/Swimspa lip above the ground height should be between 0mm to 80mm.
(2). Turn over and place to the rail prepare for the frame joint. Details drawing as below.
Height adjustable( Hexagon screw: M12*45)
insulation board QTY:2
(Short/ Long side rolling)
insulation board QTY:4
(Short side rolling)
insulation board QTY:4
(Long side rolling)
Hexagon screw: M8*35
8
(3). Joint the frames to one piece.
Use 6-8 pcs of locking Plier to hold the frames together and then screw (Hexagon screw:
M12*110).
Step 4. Height adjustment
Step 5. Rack installation(Automatic configuration)
squared nut
Rack pad
hexagon
screw:M8*55
9
Install position:
Step 6. Chain groove installation(Automatic configuration)
Step 7. Safety infrared detector installation(Automatic configuration)
Rack
Fram
Chain groove
hexagon
screw:M6*25
Hexagon
screw:M6*25
Square nut
Infrared detector cover
10
Step 8. Seal rubber installation (1).Slid in the #3 seal rubber
(2).Slid in the #2 seal rubber
(3).Slid in the #1 seal rubber
Step 9. Motor system installation and operating test(Automatic configuration) (1). Install the motor base according to the drawing below:
seal rubber
seal rubber
seal rubber
11
(2). Install the chain fixing panel
(3).Wire the infrared system and the chain.
Adjust the nut to match
the rack gap.
Chain fixing
panel
Motor cabin
screw
Motor
M10 Nut
12
(4). Motor Stopper installation
Left stopper Right Stopper
After finished stopper installation, power on and test operating the motor.
Check the seal rubber and make sure the rubber seal well on the lip of the swimspa. For "Twin Motors Solution", please refer to Step 10, otherwise go to Step 11 directly.
Step 10.
Install the gear strip, the drag chain slot and the motor at the other moving side(of the second
motor), reference operations as below:
1.Repeat Step 5.
2.Repeat Step 6.
3.Repeat Step 8, but please do not install the stopper.
Step 11. Aluminum insulation board and water proof insulation sheet installation (1).Put the Aluminum insulation board into the frame carefully.
13
(2). Screw the water proof insulation sheet on top of the board.
3.2. Decoration materials installation
Install framework and decking materials (Subject to projector).
4. Use of the Rolling deck(Automatic configuration)
4.1 Start up
Make sure there are no people or any barrier on the rail.
Make sure no people stand on the cover while the deck is rolling.
14
Turn on the power supply; press any button to start the rolling deck.
Rolling deck will stop automatically when arriving destination.
4.2 Caution:
Keep the remote control in dry place and stay away from children.
Remote control is usable within 8m away from equipment.
Unlock the motor in emergency to move the deck manually.
4.3 Note:
Safety infrared system: The roll deck will stop automatically, when the roll deck hit a barrier
between the two detectors. Remove the barrier and press the start button in remote control to
operate the roll deck again.
The remote control button has memorial function.
In winter time, when there is frost on rail,Remove the snow on top of the deck and turn on the
heater till the frost gone.
15
5.Packing instruction
Items# List Parts Remark
Motors Assembly
attached list Motor, base, detector, wheels, wire
etc. Fragile
Frames attached list Frame, Aluminum insulation board Heavy
Accessories attached list Seal rubber, chain groove, racks, rail
etc.
On/off button
Power light