roll system - norac.ca

Sprayer Specific Installation Guide John Deere 4700, 4710, 4720 Active Roll Upgrade to UC7 Boom Height Control System

This document contains specific information for the sprayer model listed and must be used in conjunction with the UCX‐7‐INST installation manual.

Copyright 2021 by NORAC Systems International Inc. Reorder P/N: UCX‐7‐JD07A‐INST Rev A (John Deere 4700, 4710, 4720 Active Roll) NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and without the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information contained in this manual. The technical information in this manual was reviewed at the time of approval for publication.

WWW.NORAC.CA

PRECISION DEFINED

Contents

1 Parts Overview ...................................................................................................................... 1

2 Ultrasonic Sensor Installation ................................................................................................ 3

3 Sprayer Interface Cabling Connections ................................................................................. 4

4 Cable Schematics ................................................................................................................... 6

5 Hydraulic Schematic ............................................................................................................ 10

Every effort has been made to ensure the accuracy of the information contained in this manual. All parts supplied are selected to specially fit the sprayer to facilitate a complete installation. However, NORAC cannot guarantee all parts fit as intended due to the variations of the sprayer by the manufacturer.

Please read this manual in its entirety before attempting installation.

WWW.NORAC.CA

PRECISION DEFINED

Page 1 Visit www.solutions.norac.ca for more system installation and troubleshooting info.

1 Parts Overview

1.1. Electronic Installation Overview

Figure 1: Electronic Installation Overview

NOTE: Items shown in BLUE are included in the display package and may not be exactly as shown.

WWW.NORAC.CA

PRECISION DEFINED


1.2. List of Parts

The following parts are specific for this sprayer model.

Item Part Number Name Quantity

B10 44695‐21 PIN ACTIVE ROLL JD UPPER MOUNTING KIT 1

B13 105416 CLAMP ROUND 1‐1/4 IN SS 5/16 X 1‐1/4 4

C10 50130‐01 CBL, VLV 4PIN TO 2PIN DT 1

C11 50120‐06 CBL, TEMP‐BYPASS DT T 528CM 208IN 1

C15 50130‐17 CBL, SC MAIN I/F JD 152CM 60IN 1

C20 50140‐10 CBL, I/F JD 30 SERIES 1

C30 43250‐07 CBL, PWR JD FUSED 1

M03 UCX‐7‐JD07‐INST MAN UC7 INST UPG JOHN DEERE 4700, 4710, 4720 1

WWW.NORAC.CA

PRECISION DEFINED


2 Ultrasonic Sensor Installation

2.1. Wing Sensor Installation

Figure 2: Outer Wing Bracket Mounting

Figure 3: Inner Wing Bracket Mounting

2.2. Main Lift Sensor Installation

Figure 4: Main Lift Bracket Mounting

WWW.NORAC.CA

PRECISION DEFINED


3 Sprayer Interface Cabling Connections

1. Connect the temperature probe (C11) to the HCM1 (temp/9 connector). Connect the temperature probe to the hole labelled “TP” on the valve block using the supplied 3/8” x 1/2” (9.5 mm x 25 mm) bolt (Figure 5). If the valve block does not have a “TP” location, connect the new temperature probe to location where the previous temperature probe was installed.

2. Tee the connectors on cable C11 into the jam valve connection.

Figure 5: Valve Block with Temperature Probe Installed

Figure 6: Jam Valve Connector

3. Connect the valve cables (C10) to the valve coils and the HCM1. The cable connected to connector (7,8) should be connected to the 3rd station coils, furthest from the “P” and “T” ports.

4. Connect the 4‐pin connector to the HCM1 main lift connector. Tee the connectors on cable C15 into the main up and main down functions on the sprayer.

Insert tee connector

here

WWW.NORAC.CA

PRECISION DEFINED


5. Connect the 12‐pin connector on cable C20 to the HCM1. Tee the connectors on cable C20 into the sprayer’s left up, left down, right up, and right down functions. Connect the main up connectors on C20 together. Connect the main down connectors on C20 together. Ensure that the main up and down connectors will not interfere or catch on anything. These connectors are not used for this installation.

There is one set of different connectors included with the tilt interface cable. Some John Deere sprayers use this connector on the left down function. If the sprayer has this connector, remove the existing connectors using the included pin removal tool. Insert the wires into the new connector and ensure they are in the same position as they were in the previous connector.

Ensure that all unused connectors are plugged with the plugs provided.

6. Connect the power cable (C30) to the tee supplied in the display kit as per Figure 1. Connect the opposite end of the cable to the appropriate keyed power connection.

WWW.NORAC.CA

PRECISION DEFINED


4 Cable Schematics

4.1. Item C11: 50120‐06 ‐ CBL, TEMP‐BYPASS DT T 528CM 208IN

WWW.NORAC.CA

PRECISION DEFINED


4.2. Item C15: 50130‐17 ‐ CBL, SC MAIN I/F JD 152CM 60IN

WWW.NORAC.CA

PRECISION DEFINED


4.3. Item C20: 50140‐10 – CBL, I/F JD 30 SERIES

WWW.NORAC.CA

PRECISION DEFINED


4.4. Item C30: 43250‐07 ‐ CBL, PWR JD FUSED

WWW.NORAC.CA

PRECISION DEFINED


5 Hydraulic Schematic

The hydraulic schematic is included for reference purposes only.

WWW.NORAC.CA

PRECISION DEFINED


Notes

TOPCON Agriculture Canada 3702 Kinnear Place

Saskatoon, SK S7P 0A6

TOPCON Agriculture Americas W5527 Hwy 106

Fort Atkinson, WI 53538

TOPCON Precision Agriculture Europe Avenida de la industria, 35, Tres Cantos, España

Spain

Support Phone: 888 979 9509

E‐mail: [email protected] Web: www.norac.ca

roll system - norac.ca

Documents