rola roof racks vehicle compatibility guide vfa6o0 5 … · rola roof racks 5 year warranty ......
TRANSCRIPT
Rola Roof Racks 5 Year Warranty
Rack System: (“Rola Roof Rack”). The Rola Roof Rack incorporates three components:
Cross Bars
End Supports
Fit Kit
VEHICLE COMPATIBILITY & WARRANTY
For more information visit www.rola.com.au
Cequent warrants that, subject to the exclusions and limitations below, the Rola Roof Rack will be free from
defects in materials and workmanship for a period of 5 years commencing on the date of sale by the
authorised Rola stockist to the original purchaser of the entire Rola Roof Rack, including the End Support, Fit
Kit and Cross Bars.
If a defect appears in the Rola Roof Rack before the end of the warranty period and Cequent finds the Rola
Roof Rack to be defective in materials or workmanship, Cequent will, in its sole discretion, either:
1. Repair the Rola Roof Rack or the defective component of the Rola Roof Rack free of charge;
2. Replace the Rola Roof Rack or the defective component of the Rola Roof Rack; or
3. Refund the purchase price of the Rola Roof Rack to the original purchaser.
Cequent reserves the right to change the design, specifications or composition of the Rola Roof Rack without
notice and without liability.
Cequent reserves the right to replace defective products or components with products or components of
similar quality, grade and composition, where an identical product or component is not available.
Goods presented for repair may be replaced by refurbished goods of the same type rather than being repaired.
Refurbished parts may be used to repair the goods.
The 5 year warranty only applies where the entire Rola Roof Rack is purchased in one transaction and is
installed and used together.
The 5 year warranty does not apply where:
1. The Rola Roof Rack is not installed in compliance with the fitting instructions provided;
2. The Rola Roof Rack is not used as intended or designed;
3. Any part of the Rola Roof Rack, such as the End Supports, Fit Kits, or Cross Bars, is used with
other products or components notintended to be used in conjunction with the modular Rola Roof
Rack system;
4. The Rola Roof Rack has been on-sold or assigned by the original purchaser;
5. The Rola Roof Rack has been modified or repaired by someone other than Cequent or an authorised
Rola stockist;
6. Cequent cannot establish any fault in the Rola Roof Rack after testing;
7. The Rola Roof Rack has been subject to abnormal conditions, including fire, water, humidity,
pressure, stress or similar;
8. The defect in the Rola Roof Rack has arisen due to abuse, misuse, neglect or accident;
9. The defect in the Rola Roof Rack has arisen due to the unlawful or unusual operation of the vehicle
to which it is fitted;
10. The defect in the Rola Roof Rack has arisen due to the purchaser’s failure to properly assemble,
install, fit, maintain or use the Rola Roof Rack in accordance with the specifications and instructions
provided by Cequent.
For safety and use instructions, please refer to any General or Specific Fitting Instructions and Use & Care
Instructions enclosed with the Rola Roof Rack or on our website at www.rola.com.au.
This warranty does not extend to fair wear and tear. Warranty claims can be made by contacting Cequent
directly using the details below. A warranty claim must be accompanied by proof of purchase (such as receipt)
and details of the alleged defect.
It is the purchaser’s responsibility to arrange and pay for any warranty claims, including the shipment of goods
to Cequent for inspection. The purchaser may seek reimbursement from Cequent for the costs of such
activities, providing Cequent notifies the purchaser in writing that a warranty claim is justified. Any such
claims must be made in writing via post or email.
The benefits of this warranty are in addition to any rights and remedies imposed by Australian State and
Federal legislation that cannot be excluded. Nothing in this warranty is to be interpreted as excluding,
restricting or modifying any State or Federal legislation applicable to the supply of goods and services which
cannot be so excluded, restricted or modified.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount to a major failure. Cequent makes no express
warranties or representations other than set out in this warranty.
Vehicle Compatibility GuideThis Fit Kit is compatible with the following vehicles.
Make Model Year
Ford Territory 4D SUV SZ 05/2011 - on
Hyundai Accent 5D Hatch RB2 07/2013 - on
Hyundai i30 5D Hatch GD 05/2012 - on
Mazda CX5 5D SUV KE 02/2012 - on
Mitsubishi ASX 5D SUV XB 08/2012 - on
Mitsubishi Outlander 4D wagon ZJ 1/2012 - on
IF YOUR VEHICLE IS NOT LISTED HERE
We are constantly adding vehicles to these kits, If the set-up instructions for your vehicle do not
appear in this guide, go to www.rola.com.au/fitkits/vca600.pdf for your set up information
Mazda 3 4D Sedan BL 04/2009 - 11/13
Mazda CX9 5D SUV TB 12/2007 - on
Peugeot 4008 5D SUV 06/2012 - on
Mazda 3 4D Sedan BM 11/2013 - on
Mazda 3 5D Hatch BL 04/2009 - 11/13
Mazda 6 4D Sedan GJ 12/2012 - on
Mazda 3 5D Hatch BM 11/2013 - on
Mazda 2 5D Hatch DJ 09/2014 - on
The repair or replacement of Rola Roof Racks or part there of, or a refund of the purchase price of the Rola Roof Rack, is the absolute limit of Cequent’s liability under this express warranty.Cequent, a division of TriMas Corporation Pty Ltd. 49 Pacific Drive, Keysborough, VIC, 3173. Phone 1800 812 017. www.rola.com.au. For detailed warranty information visit us online.
VFA6O0Revision M
Please complete the Warranty form on the reverse side and post to:
PO BOX 4050Dandenong South
VIC 3164Australia
ABN 60 004 546 543
Front RH
LH
(x) mm
Equal =
Equal =
Equal = Equal =
(x) mm
End Support Distance and Bar length
27-0850Rear RH
27-0848Front RH
27-0851Rear LH
27-0849Front LH
If speci�ed to do so, �t the supplied Pad adaptors to the feet of each End Support in the location indicated. The numbers shown to the left correspond to the correct location of the feet pads. The numbers are moluded in the underside of each part. The numbers shown above in the vehicle table correspond to the correct adaptor block to be inserted in the foot pad (if required)Refer to step 1 of the �tting instructions for more information.
Pad Adaptor Requirement(shown from the underside)
Locating and setting up the stud
Anchor Points can be found in the weather Strip on the Roof of the vehicle. The hole will either be covered with a hatch or screw. Refer to the vehicle speci�c information and follow the instructions for correct installation height position. Screw the anchor point bolt into the hole making sure to measure from the top of the bolt to the roof line.
screw cover
(x) mm
End support distance from mid-pillar Distances for setting out your racks arede�ned from the mid pillar of thevehicle. Both forward and rearwardmeasurements are given to the centre ofthe bolt.Take care to set your racks outas shown to ensure your racks �t andperform as they have been design to.Right & Left hand sides of the vehicle arede�ned as you would be when sitting inthe vehicle
Front
Mid pillar
A B00mm 00mm
Your roof rack is at its strongest and looks its best when the cross bar is centred equally within the end supports. Measure the distance between end supports on the underside of the bar. Slide the end supports until the distance between them is correct and the cross bar is centred. Lock the bars in place using the locking lever and proceed to the next step.
Installation Guidefollow the vehicle specific instructions to set up your racks correctly
Height of Anchor Studmeasured from roof line (x)
End Support Distanceand Bar length (x) Pad Apaptors
End Support Distance from Mid Pillar
Concealed
Extended
Make Model Door/Body Series Released Finished
Hatch cover
Front 855mmRear 835mm
Front 280mmRear 360mm
N/AN/A
N/AN/A
Mazda 3 4D sedan BL 04/2009 11/ 2013 Height above57mm-63mm
Hyundai i30 5D hatch GD 05/2012 on Front 852mmRear 822mm
Front N/ARear N/A
N/AN/A
N/AN/A
Hyundai Accent 5D hatch RB2 07/2013 on Front 820mmRear 830mm
Front N/ARear N/A
Height above57mm-63mm
N/AN/A
N/AN/A
N/AN/A
N/AN/A
Ford Territory 4D SUV SZ 05/2011 on Front 760mmRear 760mm
Front 115mmRear 935mm
Height above57mm-63mm
Height above57mm-63mm
Rola Roof Rack Warranty Registration CardTo ensure smooth handling of any warranty claims, please complete the form below and send to the address indicated overleaf.
Name
Address
Suburb
Dealer/Reseller
Suburb
Vehicle Make
Model/Year
Product/Part Numbers
Customer Details
Store Details
Vehicle/Product Details
Please tick if you do not wish to receive product information or marketing offersfrom Rola.
Front 870mmRear 830mm
Front 280mmRear 360mm
N/AN/A
N/AN/A
Mazda 3 5D Hatch BL 04/2009 11/ 2013 Height above57mm-63mm
Installation Guidefollow the vehicle specific instructions to set up your racks correctly
Height of Anchor Studmeasured from roof line (x)
End Support Distanceand Bar length (x) Pad Apaptors
End Support Distance from Mid PillarMake Model Door/Body Series Released Finished
Mazda CX9 5D SUV TB 12/2007 on Front 955mmRear 930mm
Front 260mmRear 800mm
Height above57mm-63mm
N/AN/A
N/AN/A
Mitsubishi ASX 5D SUV XB 08/2012 on Front 895mmRear 840mm
Front 245mmRear 480mm
Height above57mm-63mm
N/AN/A
N/AN/A
Front 900mmRear 885mm
Front 230mmRear 480mm
N/AN/A
N/AN/A
Peugeot 4008 5D SUV 06/2012 on Height above57mm-63mm
N/AN/A
N/AN/A
Front 760mmRear 760mm
Front 115mmRear 935mm
Height above57mm-63mm
N/AN/A
N/AN/A
Front 760mmRear 760mm
Front 115mmRear 935mm
Height above57mm-63mm
Height above57mm-63mm
N/AN/A
N/AN/A
Mazda CX5 5D SUV KE 02/2012 on Front 885mmRear 830mm
Front 130mmRear 740mm
Height above57mm-63mm
Front 900mmRear 885mm
Front 230mmRear 480mm
N/AN/A
N/AN/A
Citroen C4 Aircross 5D SUV 06/2012 on Height above57mm-63mm
N/AN/A
N/AN/A
Mazda 6 4D Sedan GG 08/2005 01/2008 Front 800mmRear 770mm
Front 300mmRear 370mm
Height above57mm-63mm
N/AN/A
N/AN/A
Mazda 3 4D Sedan BK 07/2006 04/2009 Front 845mmRear 832mm
Front 320mmRear 340mm
Height above57mm-63mm
Ford Territory 4D SUV SX 05/2004 09/2005
Ford Territory 4D SUV SY 10/2005 04/2011
Front 870mmRear 800mm
Front 320mmRear 370mm
N/AN/A
N/AN/A
Peugeot 307 3D Hatch T5 12/2001 10/2005
Height above57mm-63mm
Front 870mmRear 800mm
Front 150mm approxRear 520mm approx
N/AN/A
N/AN/A
Peugeot 307 5D Hatch T5 12/2001 10/2005
Height above57mm-63mm
Front 935mmRear 880mm
Front N/ARear N/A
N/AN/A
N/AN/A
Land Rover Discovery 4D SUV SERIES 3 04/2005 09/2009
Front 935mmRear 885mm
Front 240mm approxRear 410mm approx
N/AN/A
N/AN/A
Mazda 6 4D sedan GJ 12/2012 on Height above57mm-63mm
Height above57mm-63mm
Front 1035mmRear 1025mm
Front N/ARear N/A
N/AN/A
N/AN/A
Land Rover Range Rover Sport 5D suv L320 08/2005 05/2013
Installation Guidefollow the vehicle specific instructions to set up your racks correctly
Height of Anchor Studmeasured from roof line (x)
End Support Distanceand Bar length (x) Pad Apaptors
End Support Distance from Mid PillarMake Model Door/Body Series Released Finished
Front 947mmRear 902mm
Front 350mm approxRear 400mm approx
N/AN/A
N/AN/A
Mitsubishi Outlander 4D Wagon ZJ 11/2012 on Height above57mm-63mm
Special Installation where Anchor Points are hidden:
1 2 3
Carefully peel back each weather strip on the car roof. Beneath the weather strip two anchor points can be found.
Directly above the Anchor Point mark a reference point on the weather strip.
Once weather strip is fully removed from the car, use an 8mm drill bit to create a hole in the weather strip. Ensure the hole aligns with the anchor point on roof.
Height above57mm-63mm
Front 845 mmRear 830 mm
Front 350Rear 350
N/AN/A
N/AN/A
Mazda Mazda 3 5D Hatch BK 01/2004 08/2009
Front 935mmRear 875mm
Front 250mm approxRear 430mm approx
N/AN/A
N/AN/A
Mazda 3 5D Hatch BM 11/2013 on Height above57mm-63mm
Front 925mmRear 855mm
Front 260mm approxRear 400mm approx
N/AN/A
N/AN/A
Mazda 3 4D Sedan BM 11/2013 on Height above57mm-63mm
Front 810mmRear 760mm
Front 244mm approxRear 520mm approx
N/AN/A
N/AN/A
Mazda 2 5D Hatch DJ 09/2014 on Height above57mm-63mm
ROLA Ambassador Josh Sanders - Australian Pro Wakeboarder
ROLA Ambassador Niki Gudex - Australias Number One Female Mountain Biker
ROLA Ambassador Ryan Hipwood - Australian Pro Surfer
Mitsubishi ASX 5D SUV XA 07/2010 08/2012 Front 895mmRear 840mm
Front 245mmRear 480mm
Height above57mm-63mm
N/AN/A
N/AN/A
Installation Guidefollow the vehicle specific instructions to set up your racks correctly
Height of Anchor Studmeasured from roof line (x)
End Support Distanceand Bar length (x) Pad Apaptors
End Support Distance from Mid PillarMake Model Door/Body Series Released Finished
Ford Focus 5D Hatch LV 06/2009 07/2011 Front 870mmRear 855mm
Front 200mmRear 480mm
Height above57mm-63mm
N/AN/A
N/AN/A
Mazda 323 Astina 5D Hatch XB 08/1994 08/1998 Front 750mmRear 735mm
Front 190mmRear 360mm
Height above57mm-63mm
N/AN/A
N/AN/A
Front 950mmRear 900mm
Front N/ARear N/A
N/AN/A
N/AN/A
Subaru Tribeca 5D Wagon B9 11/2006 01/2014 Height above57mm-63mm
N/AN/A
N/AN/A
Ford Focus 5D Hatch LT 07/2007 05/2009 Front 870mmRear 855mm
Front 200mmRear 480mm
Height above57mm-63mm
N/AN/A
N/AN/A
Ford Focus 4D Sedan LV 06/2009 07/2011 Front 870mmRear 855mm
Front 200mmRear 480mm
Height above57mm-63mm
N/AN/A
N/AN/A
Ford Focus 4D Sedan LT 07/2007 05/2009 Front 870mmRear 855mm
Front 200mmRear 480mm
Height above57mm-63mm
N/AN/A
N/AN/A
Ford Focus 5D Hatch LS 06/2005 06/2007 Front 870mmRear 855mm
Front 200mmRear 480mm
Height above57mm-63mm
N/AN/A
N/AN/A
Ford Focus 4D Sedan LS 06/2005 06/2007 Front 870mmRear 855mm
Front 200mmRear 480mm
Height above57mm-63mm
N/AN/A
N/AN/A
Mazda 6 4D Sedan GY 08/2002 07/2005 Front 800mmRear 770mm
Front 300mmRear 370mm
Height above57mm-63mm