rgbw 4 in 1 24v strip light connection guide - ecolocity led · rgbw 4 channel color controller + _...
TRANSCRIPT
Ribbon Star 4 in 1 RGBW LED Strip Light - 24VDCSKU: RL-DX-4IN1
EcolocityLED.com [email protected] 775-636-6060
SPECIFICATIONS
PRECAUTIONS
1 0 9 2 G r e g S t r e e tSparks, NV 89431, USA E C O L O C I T Y L E D . C O M 7 7 5 - 6 3 6 - 6 0 6 0
!
24VDC24VDC3M VHB3M VHB3M VHB3M VHB
3M VHB3M VHB3M VHB3M VHB
120VAC
Use 24VDC Input Only!
DO NOT use AC Input!
WARNING – This product should be installed, cut and connected only by a qualified professional.
This product is not designed to be installed in wet or damp environments.
NEVER cut, connect, or join wires while product is connected to a live power source.
DO NOT bend, fold or crease the strip in a manner that will damage the conductivity of the circuit board.
DO NOT use in direct sunlight.DO NOT use in environments over 113°F.DO install on a metal heat sink.
DO NOT exceed 30ft serial connection!BE CERTAIN your 24VDC source and wire gauge is suffice for powered load.
Copper Pads for Connections.
Connections can be made at any point strip light.
Never cut outsideof cut lines!!
3.93” (10cm) Cut Lines
0.65” (1.66cm)
5mm0.47”(12mm)
5mm
RGBW, 5050 SMD4in1 LEDs
Product SKU :LED Size :
LED Quan�ty :Input Power :
Wa�s :Max Serial Connec�on :
Opera�ng Temp :Beam Angle :
Ra�ng :Warranty Period :
RL-DX-4IN15050 SMD6 LEDs per 3.93" 24VDC Constant Voltage 5.1W per foot30�-4° ~ 113°F120°Dry2 Years
Input Power: 24VDC Constant Voltage
Power supply equa�on
X * 5.10 = Y
X = linear strip light footageY = minimum transformer wattage
DC +WhiteGreenRedBlue22AWG Stranded Wire
CONNECTION EXAMPLES: 5.1 Watts per foot
EcolocityLED.com [email protected] 775-636-6060
118” Strip wired to 24VDC RGBW Controller(Use Parallel Connec�ons every 30�)
+_
+_
+_
+_
DC+
DC-
V+
R-
G-
B-
W-
118” (3m)
24VDCPOWER SUPPLY
T0 110-220VAC
Mul�ple Strips wired to 24VDC RGBW Controller(Example of Parallel Connec�on)
+_
+_
+_
+_
DC+
DC-
V+
R-
G-
B-
W-
30ft 30ft
24VDCPOWER SUPPLY
T0 110-220VAC
Strips wired to 24VDC RGBW Controller & Signal Amp(Use Parallel Connec�ons every 30�)
+_
+_
+_
+_
DC+
DC-
V+
R-
G-
B-
W-
DC-
DC+
WBGRV+
W
B
G
R
V+
I����
O��
���
Use SignalAmp to Extend
Max ControllerLoad
24VDCPOWER SUPPLY
T0 110-220VAC
T0 NEXT 30FT
����� ������ ��� ���������� ��� ������ ������ ���� �� ������� ���� ��� ���� �� ��� ����� ����� ������.
Ribbon Star 4 in 1 RGBW LED Strip Light - 24VDCSKU: RL-DX-4IN1INSTALLATIONREQUIRED SUPPLIES OPTIONAL SUPPLIES
Cleaning Suppliesor Degreaser
Stranded Wire andWire Strippers
Wire Nuts orConnectors
24VDC PowerSupply
RGBW 4 ChannelColor Controller
+_
+_
+_
+_
DC+
DC-
V+
R-
G-
B-
W-
LED CONTROLLER
PAUSE
=
MODE-
MODE+
SPEED-
SPEED+
BRT-
BRT+
Solder, Solder Iron and Heat Shrink(Required to cut and re-connect)
pg. 2 of 3
1.) Clean Mounting Surface
Use your cleaning supplies to clean your moun�ng surface. Please note that moun�ng surface must be smooth, clean and dry for the 3M tape to permanently adhere.
2.) Connect Transformer
WARNING – This step should be done by a qualified professional. Always disable AC power before connec�ng! Use wire nuts or connectors to secure your AC input to your 24V transformer.
NEUTRALNEUTRALLOAD
GROUND
3.) Connect Controller
Always be certain power is disabled before connec�ng! Use a small screw driver to connect your 24VDC posi�ve and nega�ve wires to your 4 channel RGBW controller input.
+_
+_
+_
+_
DC+
DC-
V+
R-
G-
B-
W-
4.) Test and Mount Strips
Always test your strip lights before adhering the 3M double sided tape. Never test the strip light when rolled inside the plas�c reel.
3.) Connect Strip Lights
Always be certain power is disabled before connec�ng! Use a screw driver to connect the 5 wires from your RGBW strip light to the proper output ports of your 4 channel RGBW controller.
+_
+_
+_
+_
DC+
DC-
V+
R-
G-
B-
W-
STRIP LIGHT ACCESSORIES:
EcolocityLED.com [email protected] 775-636-6060
Ribbon Star 4 in 1 RGBW LED Strip Light - 24VDCSKU: RL-DX-4IN1SOLDERING INSTRUCTIONREQUIRED SUPPLIES OPTIONAL SUPPLIES
Rosin CoreElectrical Solder
Electrical Soldering Iron(Preferably Temp Adjustable)
MaskingTape
Heat Shrink and Heat Gun(Recommended but not required)
pg. 3 of 3
1.) Strip and Tin Wire
Heat your soldering iron to 500-600°F. Strip your 2 conductor stranded wire roughly 1/8”. Tin the exposed wires with rosin core solder.
2.) Tin Strip Light Pads
Cut your strip light to length on cut line between copper pads. Tin each copper pad with rosin core solder. Do not bridge solder between copper pads.
3.) Solder Wire to Strip
Mate your �nned wire to the copper pad with respec�ve polarity. Black wire to DC+. Be sure that no wires or solder are touching on another.
4.) Test and Heat Shrink
Test your soldered connec�on for con�nuity or any electrical arcing. Once tested you can cover exposed copper pads with heat shrink if desired.
Stranded Wire andWire Strippers
22AWG RGBWConnection Wire
24VDC Power Supplies RGBW LED Controllers Aluminum Extrusions and Covers
HELPFUL LINKS:24VDC Power Supplies - http://www.ecolocityled.com/category/led_power_supplies_24v RGBW LED Controllers - http://www.ecolocityled.com/category/4ch-led-controlsRGBW Connec�on Wire - http://www.ecolocityled.com/product/rgbw-led-wire-5c Aluminum Extrusions - http://www.ecolocityled.com/category/klus-kl3-wide-led-extrusions Strip Light Soldering Guide - http://www.ecolocityled.com/category/led_tutorials_rgb_solder