release overview sv8100 r5.0 (emea) issue 2sf.nec-unified.com/docs/informations-techniques... ·...
TRANSCRIPT
SV8100 R5.0 (EMEA)
Release Overview
Date: 18 February 2011
Version: V5.0 Issue 2
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 2 of 36
Contents
1. PRODUCT SUMMARY ........................................................................................................................ 4
2. OVERVIEW ........................................................................................................................................... 5
3. NEW AND ENHANCED BUSINESS FEATURES - SOFTWARE (NON ........................................... 6
LICENSED) .................................................................................................................................................... 6
3.1 IP Address Collision Alarm ...................................................................................................... 6
3.1.1 Benefits .............................................................................................................................. 7
3.1.2 Required Software and Hardware ..................................................................................... 7
3.1.3 Required Training .............................................................................................................. 8
3.2 IP Address of 3rd
Party TAPI Device ........................................................................................ 9
3.2.1 Benefits .............................................................................................................................. 9
3.2.2 Required Software and Hardware ..................................................................................... 9
3.2.3 Required Training .............................................................................................................. 9
3.3 Minibar confirmation .............................................................................................................. 10
3.3.1 Benefits ............................................................................................................................ 10
3.3.2 Required Software and Hardware ................................................................................... 10
3.3.3 Required Training ............................................................................................................ 10
3.4 Transfer of un-dialled lines ..................................................................................................... 11
3.4.1 Benefits ............................................................................................................................ 11
3.4.2 Required Software and Hardware ................................................................................... 11
3.4.3 Training Course Required ............................................................................................... 11
3.5 Call-forward on one key .......................................................................................................... 12
3.5.1 Benefits ............................................................................................................................ 12
3.5.2 Required Software and Hardware ................................................................................... 12
3.5.3 Training Course Required ............................................................................................... 12
3.6 Guest Name to IP DECT Phone .............................................................................................. 13
3.6.1 Benefits ............................................................................................................................ 13
3.6.2 Required Software and Hardware ................................................................................... 13
3.6.3 Training Course Required ............................................................................................... 13
3.7 Disconnect supervision operation for BCT wrapup ................................................................ 14
3.7.1 Benefits ............................................................................................................................ 14
3.7.2 Required Software and Hardware ................................................................................... 14
3.7.3 Training Course Required ............................................................................................... 14
4. NEW AND ENHANCED BUSINESS FEATURES - SOFTWARE (INDIVIDUALLY LICENSED)15
4.1 ACD Skill Based Routing ........................................................................................................... 15
4.1.1 Benefits ............................................................................................................................ 16
4.1.2 Required Software and Hardware ................................................................................... 16
4.1.3 Required Training ............................................................................................................ 16
4.2 XMLPro .................................................................................................................................... 18
4.2.1 Benefits ............................................................................................................................ 18
4.2.2 Required Software and Hardware ................................................................................... 18
4.2.3 Required Training ............................................................................................................ 18
5. NEW AND ENHANCED BUSINESS FEATURES - SOFTWARE (ADVANCED FEATURE
LICENSE ITEMS) ........................................................................................................................................19
5.1 IP DECT Enhancements – 2nd
Call Information ..................................................................... 19
5.1.1 Benefits ............................................................................................................................ 19
5.1.2 Required Software and Hardware ................................................................................... 19
5.1.3 Training Course Required ............................................................................................... 20
5.2 IP DECT Enhancements – CLI on Transfer ............................................................................ 21
5.2.1 Benefits ............................................................................................................................ 21
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 3 of 36
5.2.2 Required Software and Hardware ................................................................................... 21
5.2.3 Training Course Required ............................................................................................... 21
5.3 NETLINK: Multi-SIP carriers ................................................................................................. 22
5.3.1 Benefits ............................................................................................................................ 22
5.3.2 Required Software and Hardware ................................................................................... 22
5.3.3 Training Course Required ............................................................................................... 23
5.4 Callback to Cell Phone ............................................................................................................ 24
5.4.1 Benefits ............................................................................................................................ 24
5.4.2 Required Software and Hardware ................................................................................... 24
5.4.3 Training Course Required ............................................................................................... 25
5.5 Memo Display Function .......................................................................................................... 26
5.5.1 Benefits ............................................................................................................................ 26
5.5.2 Required Software and Hardware ................................................................................... 26
5.5.3 Training Course Required ............................................................................................... 27
5.6 Name History of Outgoing Call .............................................................................................. 28
5.6.1 Benefits ............................................................................................................................ 28
5.6.2 Required Software and Hardware ................................................................................... 28
5.6.3 Training Course Required ............................................................................................... 28
5.7 Automatic Access to InMail by CallerID ................................................................................ 29
5.7.1 Benefits ............................................................................................................................ 29
5.7.2 Required Software and Hardware ................................................................................... 29
5.7.3 Training Course Required ............................................................................................... 30
5.8 KCCIS Callback ...................................................................................................................... 31
5.8.1 Benefits ............................................................................................................................ 31
5.8.2 Required Software and Hardware ................................................................................... 31
5.8.3 Training Course Required ............................................................................................... 31
5.9 External Paging Enhancement ................................................................................................. 32
5.9.1 Benefits ............................................................................................................................ 32
5.9.2 Required Software and Hardware ................................................................................... 32
5.9.3 Training Course Required ............................................................................................... 32
6. SOFTWARE AND HARDWARE ........................................................................................................33
7. TECHNICAL DOCUMENTATION ....................................................................................................34
8. TECHNICAL COURSES .....................................................................................................................35
9. DOCUMENT HISTORY ......................................................................................................................36
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 4 of 36
1. PRODUCT SUMMARY Business today demands efficient, seamless communication to enable rapid decision-making and
customer responsiveness. NEC’s UNIVERGE®360 is our approach to help small to medium-sized
businesses succeeds at this accelerated level by unifying all aspects of business communication. The
UNIVERGE SV8100 Communications Server is an integral part of this initiative.
The SV8100 Communications Server is the ideal system for small to medium-sized businesses that
wish to compete and grow their businesses over time. This robust, feature-rich solution is scalable and
can be expanded to meet your communications needs both now and in the future.
Designed to be both versatile and scalable for growing business needs, the SV8100 supports IP, TDM
video, wired or wireless. It also provides high-powered features and applications that can be
transparently shared between branch or remote locations. Individuals, departments and locations can
work more efficiently by using this feature to communicate seamlessly in real time.
The UNIVERGE® SV8100 Communications Server provides converged communications - telephony,
data and video over an IP infrastructure. The solution is targeted at the small to medium sized business
and supports between 8 and 512 users on a single site, and a variety of networking possibilities.
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 5 of 36
2. OVERVIEW SV8100 R1 series software was introduced with the release of the UNIVERGE SV8100. The SV8100
continues to provide new and enhanced features with the release of 8100 R5.0 series software and new
hardware items.
R5.0 software and hardware includes the new and enhanced features :-
SV8100 Software
Non-license items
IP Address Collision Alarm
IP Address of 3rd
Party TAPI Device
Minibar confirmation
Transfer of un-dialled lines
Call-forward on one key
Guest Name to IP DECT Phone
Disconnect supervision operation for BCT wrap-up
Individually Licensed Items
ACD Skill Based Routing
XMLPro
Advanced Feature License items
IP DECT Enhancements
Netlink: Multi-SIP carriers
Callback to Cell Phone
Memo function
Name History of outgoing Call
Automatic Access to VM by Caller ID
KCCIS Callback
External Paging Enhancement
SV8100 Applications
PC Programming
MyCalls R3 – Refer to MyCalls R3 Overview
For additional information on the SV8100 please refer to Product Overview SV8100 R5 document. All
training courses against new items require the relevant pre-requisite courses.
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 6 of 36
3. NEW AND ENHANCED BUSINESS FEATURES - SOFTWARE (NON
LICENSED)
3.1 IP Address Collision Alarm
IP Duplication can cause several issues, one typical issue is one way speech.
The SV8100 can monitor IP duplication by using “Gratuitous ARP” (performing an ARP of own
address/es.) to check if any other device is showing registered as this address.
This is a periodic task performed every 5 minutes (non-programmable).
The SV8100 can check for duplication of the CCPU IP addresses and IPLA IP addresses.
See the following table for addresses checked, alarm name and priority.
Collision check PRG Alarm display name Alarm display priority
PRG 10-12-01 Collision(01) 10
PRG 10-12-09 Collision(02) 1
PRG 84-26-01 GW:1 Collision(03) 2
PRG 84-26-01 GW:2 Collision(04) 3
PRG 84-26-01 GW:3 Collision(05) 4
PRG 84-26-01 GW:4 Collision(06) 5
PRG 84-26-01 GW:5 Collision(07) 6
PRG 84-26-01 GW:6 Collision(08) 7
PRG 84-26-01 GW:7 Collision(09) 8
PRG 84-26-01 GW:8 Collision(10) 9
The alarm of the IP collision can be displayed with the following terminal types :-
DT300
DT700
DTerm
Displayed as below:-
1-4 FRI 8:53PM Collision(01)192.168.0 .XXX List Dir ICM Prog
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 7 of 36
Or View Alarm reports in Pc Programming. Param 2 shows the IP address conflict, 2 is Collision(02).
Note : This functionality is only available on same subnet, cannot be performed over routed networks.
3.1.1 Benefits
Provides increased diagnostic facilities for field issues.
3.1.2 Required Software and Hardware
• SV8100 R5 Software
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 8 of 36
3.1.3 Required Training
• If SV8100 trained no extra training required
To configure :
PRG CMD 90-10 Alarm 57 Set alarm as Not Set, Minor (def) or Major.
PRG CMD 90-10 Alarm 57 Set to Report (def: Off)
PRG CMD 90-50 Enter Extension to send alarm to. e.g 200
Or via Easy Edit .
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 9 of 36
3.2 IP Address of 3rd
Party TAPI Device
The SV8100 will show the IP address of CTI device currently connected to the 3rd party CTI interface
(PRG CMD 10-20-01).
The IP Address is shown as a read only entry in PRG CMD 20-23-06.
3.2.1 Benefits
Allows easy finding of 3rd
Party TAPI server connected to the SV8100
3.2.2 Required Software and Hardware
• SV8100 R5 Software
3.2.3 Required Training
• No extra training required.
PRG CMD
20-23-06
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 10 of 36
3.3 Minibar confirmation
Pre R5When entering minibar items at a guest phone confirmation tones were not heard.
From SV8100 R5 confirmation tones will be heard when entering minibar items on Guest phone.
This will be heard after entering the quantity:-
So operation would be
Dial 781 (Service Code for Hotel Set Hotel Room Data)
Dial Item number
Press Hold
Dial Quantity
Press Hold – At this point a confirmation tone will be heard.
For SLT’s Recall is used instead of Hold.
3.3.1 Benefits
Gives confidence to the Hotel staff that the information has been taken.
3.3.2 Required Software and Hardware
• SV8100 R5 Software
• Hotel interface (PMSLite or PMS on PVA with front office software)
3.3.3 Required Training
• If Hotel trained no extra training required
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 11 of 36
3.4 Transfer of un-dialled lines
Will give the ability for a managing phone e.g. Operator the chance to transfer trunk toll restricted
access to other extensions.
Uses Walking Toll Restriction
New Key: #04: Change Restriction Class
Can have multiple keys with different codes stored or key with no code to allow operator to enter a
code after pressing (useful if lots of codes, or operator using lots of keys already).
Operation:
Ext101 calls operator (100).
Operator answers.
Operator presses the programmable key followed by the Toll Restriction Code
Operator receives Complete message.
Ext 101 clears down.
Ext 101 makes call with toll restriction assigned by operator for that single call.
After call is complete, access is again blocked.
3.4.1 Benefits
Allows central position to control outbound calls. Ideal for retail industry, warehouse, etc
3.4.2 Required Software and Hardware
• SV8100 R5 Software
3.4.3 Training Course Required
• If SV8100 trained no further training required.
PRG CMD 15-07 new key #04 and enter Toll Restriction Code or leave blank (leaving blanking will
prompt the operator to enter the code after pressing the function key each time) or can use 851 and Key.
Normal Toll Restriction programming required (PRG 21-14)
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 12 of 36
3.5 Call-forward on one key
A new CFW Key function with destination. Allows multiple CFW keys to be programmed each having
own forward type and destination.
Can easily change between forwards. Toggle on and off by pressing same key.
Available key list:
10: call forward - immediate
11: call forward - busy
12: call forward - no answer
13: call forward - busy/no answer
14: call forward - both ring
Operation:
Dial service code 851
Press Programmable key
Dial 2 digits Key code (10,11…)
Dial number to be transferred
Press Hold
3.5.1 Benefits
Gives bet user experience. Allows easy setting and using of forwards.
3.5.2 Required Software and Hardware
• SV8100 R5 Software
3.5.3 Training Course Required
• If SV8100 trained no further training required.
CMD 15-07 Select Forward Type – Enter destination
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 13 of 36
3.6 Guest Name to IP DECT Phone
SV8100 R5 will allow Guest name to be sent to IP DECT phone when the Guest phone makes a call to
the IP DECT Phone. This allows mobile Hotel staff to instantly recognize the caller and greet
accordingly.
3.6.1 Benefits
Improves service given by Hotel Staff, allowing professional and personal answer.
3.6.2 Required Software and Hardware
• SV8100 R5 Software
• Hotel interface (PMSLite or PMS on PVA with front office software)
• DAP firmware version 5 or above.
3.6.3 Training Course Required
• If SV8100 trained no further training required.
No Programming is required to allow this feature.
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 14 of 36
3.7 Disconnect supervision operation for BCT wrapup
BCT often has agents using headset functionality, using the agent software to answer and control the
phone.
This is an excellent use of the phones and software together. Particularly when used with the disconnect
supervision feature.
Disconnect Supervision is a feature on the SV8100 that automatic clears down your phone when the
incoming caller clears down.
If the SV8100 has disconnect supervision enabled, at the end of the call the handset used by BCT would
go idle and be available for another call or remain in a wrap-up (ACW) state until BCT sees further
activity on the phone (e.g. lifting the handset). This is a useful feature and allows efficient call handling.
For those agents using a handset or a headset plugged into the handset port and uses a cradle device to
control the calls this can be an issue. When the incoming caller clears down, so does the BCT
extension, however because the handset is off hook it creates a new dial tone state. This cause BCT to
believe that the Agent is ready to come out of wrap up immediately.
For this scenario it is better that that the agents do not have disconnect supervision.
Therefore instead of the setting being global (PRG CMD 20-02-09) it has been made a class of service
setting (PRG CMD 20-13-43). Therefore allowing those members that prefer disconnect supervision on
to still have the efficiency and the BCT agents requiring the wrap-up functionality to have this disabled.
3.7.1 Benefits
Allows all modules of BCT to be used with Headset/Handset and the users preferred settings.
3.7.2 Required Software and Hardware
• SV8100 R5 Software
3.7.3 Training Course Required
• If SV8100 trained no further training required.
PRG CMD 20-13-43 Disconnect Supervision (COS) – Enable/Disable for classes required
PRG CMD 20-02-09 Disconnection Supervision (Global) - Disable
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 15 of 36
4. NEW AND ENHANCED BUSINESS FEATURES - SOFTWARE
(INDIVIDUALLY LICENSED)
4.1 ACD Skill Based Routing
Further enhancing the built in functionality of the SV8100, this function allows ACD incoming call to
be distributed to the agent based on by skill level of the agent.
This feature supports both Normal Login Mode and AIC Login Mode.
Skill Based Routing can set to each ACD group.
Skill Based Routing supports Normal Login and AIC Login.
Priority range is 1 to 7. Priority 1 is highest priority.
Call sequence
First call arrives at the free agent with highest priority (priority 1).
Second call arrives at the free agent with highest priority in this case as the priority 1 agent is
unavailable the call arrives at the priority 2 agent.
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 16 of 36
Third call arrives at the free agent with highest priority in this case as the priority 1 agent as has
finished with previous call
Only when priority 1 and 2 agents are unavailable will the priority 3 agent receive a call.
If there are any agents assigned with the same skill level, the system distributes the call in
order to agent’s waiting time (as in standard ACD).
If the LoginID (Agent) does not have a skill table assigned then the system will treat the agent
as a highest level (level 1).
When ACD Group overflow call happens, and the call is transferred to another group, then the
behaviour of the call depends on transferred group setting. For example, when the call transfers
from group 1 to group 2, skill base routing follows group 2 setting.
The agent has to log off from ACD Group when the system data will be changed. Otherwise,
the system data is not applied correctly.
4.1.1 Benefits
Gives much more flexibility and control of how calls are delivered, ensuring calls are delivered to those
best suited so the best possible service can be given.
4.1.2 Required Software and Hardware
• SV8100 R5 Software
• BE110869, LK-SYS-ACD-SKILLBASE-LIC, (2105)
4.1.3 Required Training
If ACD trained then no extra training required.
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 17 of 36
To configure:
Follow usual ACD Programming plus:
NEW PRG CMD 41-21-02 Enter Skill Table Number (1-512, def 0) against ID
NEW PRG CMD 41-22-01 Enable/Disable Skill Based Routing per group
NEW PRG CMD 41-23-01 For Skill Table and Group Enter Skill Level (1is highest Priority)
So effectively Each Login ID has a Skill Table
LoginID Skill Table
201 1
202 2
203 3
204 4
And Each Skill Table has a skill for each group.
ACD Grp 1 ACD Grp 2 ACD Grp 3 - ACD Grp 64
Skill Table 1 1 2 3 - 7
Skill Table 2 2 3 1 - 2
Skill Table 3 3 1 2 - 3
Skill Table 4 1 1 1 - 1
- - - - - -
Skill Table 512 3 3 3 - 3
So equates as:
ACD Grp 1 ACD Grp 2 ACD Grp 3 - ACD Grp 64
Agent 1 (201) 1 2 3 - 7
Agent 2 (202) 2 3 1 - 2
Agent 3 (203) 3 1 2 - 3
Agent 4 (204) 1 1 1 - 1
- - - - - -
Agent 512 3 3 3 - 3
Agent 1 has highest Priority in ACD Grp 1, but lowest in ACD Grp 64.
Or via Easy Edit
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 18 of 36
4.2 XMLPro
XMLPro is a programming interface allowing access to the SV8100 System Data for partnered
applications such as BCT, MyCalls, etc (currently working towards integrating with the interface).
This allows the applications to help self import areas such as extensions, DDI’s etc to make installation
easier, ultimately approaching near self configuration.
The interface also would allow applications to make changes to data, so give more control from the
application user.
The interface is as powerful as the application driving it!
4.2.1 Benefits
Allows greater integration between application and SV8100.
Allows for easier installation for engineer and easier configuration by end user.
Allows greater application possibilities.
4.2.2 Required Software and Hardware
• SV8100 R5 Software
• BE110868, LK-SYS-XMLPro-LIC, (0041)
4.2.3 Required Training
Details provided to partnering applications.
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 19 of 36
5. NEW AND ENHANCED BUSINESS FEATURES - SOFTWARE
(ADVANCED FEATURE LICENSE ITEMS)
5.1 IP DECT Enhancements – 2nd
Call Information
SV8100 R5 will support a 2nd
call indication. Whilst on a call (conversation only) a tone can be heard.
It is then possible to use the answer button/* can to toggle.
Notes:
• It is not possible to transfer call 1 and call 2 together.
• It is not possible for an IP DECT user to make an enquiry call whilst a 2nd
call is waiting
• It is not possible for an IP DECT user to transfer off the 1st caller whilst a 2
nd call is waiting
5.1.1 Benefits
Makes you aware of another caller attempting to reach you, allows you to make a decision whether to
continue call, and take another, or briefly speak to the new caller and return to existing call.
5.1.2 Required Software and Hardware
• SV8100 R5 Software
• BE110867, LK-SYS-V5000 Enhancements-LIC, (0034)
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 20 of 36
5.1.3 Training Course Required
• If SV8100 and IP DECT trained no further training required.
New PRG CMD 20-13-54 Call Waiting for standard SIP Terminal – 0/1 disable/enable (def 0)
Note: PRG CMD 20-13-5, 20-13-6 Off Hook Signalling and PRG CMD 20-09-01 Second Call must be
enabled.
Also the DAP must have multiple_call_appearances=yes and call_waiting_indication=Waiting. As
below :
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 21 of 36
5.2 IP DECT Enhancements – CLI on Transfer
Currently the transferring party number (name not supported) is displayed to an IP DECT phone.
SV8100 R5 will support the original CallerID display after a call transfer for both Supervised and
Unsupervised transfer.
If no CLI is available on the trunk call “Anonymous” is displayed on the IP DECT handset.
5.2.1 Benefits
Allows better recognition of callers and more accurate call history.
5.2.2 Required Software and Hardware
• SV8100 R5 Software
• BE110867, LK-SYS-V5000 Enhancements-LIC, (0034)
5.2.3 Training Course Required
• If SV8100 and IP DECT trained no further training required.
No programming is required to enable this feature.
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 22 of 36
5.3 NETLINK: Multi-SIP carriers
SV8100 R5 software introduces the ability to have multiple SIP Carriers when using Netlink.
Previously only one SIP carrier was available; now up to 16 Carriers can be used (Max one per node).
Cannot exceed the 200 Trunk Limit.
This helps provide local breakout (reducing traffic and DSP usage across Netlink) and provided
redundancy.
Notes:
Because each Node has its own details for the SIP area and cannot be replicated it is necessary to take
configurations of each when performing SIP Trunk aspects.
VLAN and QoS items are replicated so please take into consideration each nodes IT infrastructure. As
if the secondary becomes a primary, it will take the original Primary’s QoS and VLAN settings.
5.3.1 Benefits
Allows local breakout for external calls. Allows redundancy with multiple trunk carriers.
5.3.2 Required Software and Hardware
• SV8100 R5 Software
• BE110867, LK-SYS-V5000 Enhancements-LIC, (0034)
• Total number of IP Trunk licenses - LK-SYS-IP-TRUNK1-LIC (BE107582)
• Licenses and hardware required under normal Netlink conditions.
All licenses should be added to the Primary Node.
The Internet
Primary
IP Trunk No: 01-02
Secondary
IP Trunk No: 03-04
Use one DSP
Use one DSP
NetLink
System
Use Multiple Carrier
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 23 of 36
5.3.3 Training Course Required
• If SV8100 VoIP trained then no further training required
All systems should be Netlinked before programming.
All Licenses should added to the Primary.
PRG CMD 10-40 set which trunks will be on which site.
Each system should be connected to via Pc Programming or WebPro to program SIP Trunks.
Each node is programmed as would be if programming a Single system (PRG CMD 10-28, 10-29, etc.)
however the connection details (carrier address, registration details) will be different at each node.
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 24 of 36
5.4 Callback to Cell Phone
Extending the Mobile Extension functionality even further to remove outbound call charges.
Rather than the normal call in to mobile extension and receive dial tone(for which the mobile would be
charged for the call into the system), there is now the possibility to hangup after one ring and have the
system callback. When answered this presents dialtone off the system in the same way Mobile
extension normally works (the difference being that the Call charges are now at the SV8100).
Notes:
Can be used on ISDN BRI and PRI, SIP Trunks. Cannot be used with Analogue Trunks.
If on answer by the Mobile no DTMF is seen within a set time, the call is disconnected.
If all trunks are busy or not answer at the mobile, the call will not retry.
5.4.1 Benefits
Improves mobility, allows call charges to be made against the system rather than the phone. Makes
accounting easier. Means that workers can use their personal phone (if number entered) to make non
charged calls for company purposes.
5.4.2 Required Software and Hardware
• SV8100 R5 Software
• BE110867, LK-SYS-V5000 Enhancements-LIC, (0034)
Any call charges
billed to system
One ring and
hang up
Number matched
in Speed dial
and system Answer and
receive dialtone
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 25 of 36
5.4.3 Training Course Required
• If SV8100 Trained no further training required.
Set up Mobile Extension as usual, then:
New PRG CMD 15-22-04 Select Callback
The following timers apply, however these should work in their default and only need changing if
different times are required.
New PRG CMD 22-01-12 Set length of time to determine successful ring into Mobile ext and seen
hang up (def: 3secs, approx. 1 ring) and receive call back. If ring for longer
than this time the ME will answer as usual
New PRG CMD 20-01-16 Length of time the System will wait for an answer at the Mobile device
after callback (def: 15 secs).
Or if using timer classes (PRG 20-29-01 Classes 1-15)
New PRG CMD 22-31-24 Set length of time to determine successful ring into Mobile ext and seen
hang up (def: 3secs, approx. 1 ring) and receive call back. If ring for longer
than this time the ME will answer as usual
New PRG CMD 20-31-25 Length of time the System will wait for an answer at the Mobile device
after callback (def:15 secs).
New PRG CMD 20-18-01 Set how long to look for DTMF before disconnect (def: 30 secs)
Or via Easy Edit
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 26 of 36
5.5 Memo Display Function
This function gives the keyset user more information to allow better answer and handling of the
incoming call.
An incoming call can display pre-programmed information when incoming caller ID matches Common
speed dialing.
The information can be displayed automatically or key operation while ringing/conversation.
・Up to 84 characters, (28char x 3line) of free text (any information can be entered
・The information can be edited by PC programming or Web Pro.
Supported on DT330, DT700 and Softphone (Phone View)
5.5.1 Benefits
Improves user experience. Offers a near CTI type functionality for small sites. Easy to use.
5.5.2 Required Software and Hardware
• SV8100 R5 Software
• BE110867, LK-SYS-V5000 Enhancements-LIC, (0034)
Addr:XXX ABC St., Dallas, TX
Store:2010/2/12
LINE 001
1st SMB Group 0356551700
Incoming Call matches with CallerID entry
Press right cursor key to see extra memo info
Incoming Call
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 27 of 36
5.5.3 Training Course Required
• If SV8100 Trained no further training required.
Set up Mobile Extension as usual, then:
New PRG CMD 13-04-08 memo1 - Text for first line of display
New PRG CMD 13-04-09 memo2 - Text for second line of display
New PRG CMD 13-04-10 memo3 - Text for third line of display
New PRG CMD 15-02-58 Display Mode of Incoming Trunk - Sets which is displayed automatically
when ringing. 0 – Usual CLI and
Name, 1 – memo. Right key can
toggle in either case.
Or via Easy Edit
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 28 of 36
5.6 Name History of Outgoing Call
Pre R5 Name was only shown as for Incoming history.
This new function can display Speed dial name (Default) or Speed dial name and Extension name for
outgoing call history
Extension name is supported over Netlink, IP FeatureNet and KCCIS.
5.6.1 Benefits
Makes it easier for user to select from Redial list.
5.6.2 Required Software and Hardware
• SV8100 R5 Software
• BE110867, LK-SYS-V5000 Enhancements-LIC, (0034)
5.6.3 Training Course Required
• If SV8100 Trained no further training required.
No configuration is required to enable the function.
Uses the names in PRG CMD 13-04-01 for external calls and PRG CMD 15-01-01 for internal calls.
PRG CMD 15-02-13 – LND outgoing mode - 0- Extension/Trunk Mode, 1- Trunk Mode (def)
REDIAL-01 0312345678 ↑ ↓ Store DEL
Pre R5 R5
REDIAL-01 234 ↑ ↓ Store DEL
REDIAL-01 ABC Company 0312345678 ↑ ↓ Store DEL REDIAL-01 James 234 ↑ ↓ Store DEL
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 29 of 36
5.7 Automatic Access to InMail by CallerID
This function enables automatic log in to pre-programmed mail box when incoming caller ID matches
Common speed dialing.
A caller (with CLI Entry in Speed dials) can call into the SV8100 and bypass the enter mailbox number
and password menu.
5.7.1 Benefits
Allows user to dial directly into mailbox to deal with messages. Improves ease of use meaning more
likely to check voice mails.
5.7.2 Required Software and Hardware
• SV8100 R5 Software
• BE110867, LK-SYS-V5000 Enhancements-LIC, (0034)
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 30 of 36
5.7.3 Training Course Required
• If SV8100 and InMail trained no further training required.
New PRG CMD 13-04-11 – Automatic Access to Voice Mail by Caller ID - Enter 1-544
Where 1-512 are Subscriber mailboxes, 513-544 are group mailboxes
Route DDI to VM in usual method e.g. to VM ring group (102).
Or via Easy Edit
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 31 of 36
5.8 KCCIS Callback
This feature allows an extension to set KCCIS Call Back when the extension dialed across KCCIS is
busy. When this feature has been set, the setting extension will receive call back as soon as the busy
extension becomes available.
Ext 101 calls Ext 201 (over KCCIS) but Ext 201 is busy (Ext 101 receives busy tone)
Ext 101 performs Callback feature by pressing Callback key.
When Ext 201 become free, a call is made to Ext 101.
On answering the call at EXT 100, a call is then made from Ext 101 to Ext 201
Supported on DT300, DT700, Dterm and Softphone (Desktop Suite).
Callback key must be programmed (not supported via service code or soft key.
5.8.1 Benefits
Gives closer integration over KCCIS allowing caller to use functionality usually only on own system.
5.8.2 Required Software and Hardware
• SV8100 R5 Software
• BE110867, LK-SYS-V5000 Enhancements-LIC, (0034)
5.8.3 Training Course Required
• If SV8100 and VoIP trained no further training required.
PRG CMD 15-07, give extension a key Code 35
PRG 20-01-09 Camp on Cancel time – set on destination system. Amount of time to wait for
destination to become available, if not callback cancelled. Default 64800 secs.
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 32 of 36
5.9 External Paging Enhancement
This function enables a VRS Message to be played while external paging. Useful for repeated
messages or for professional sounding announcements
.
Dial External Paging code: 803 *
Enter External Page Group No: 1
Dial VRS number: 001
Above numbers maybe different depending on group and message to be used.
Only supports External paging, not available for internal or combined.
5.9.1 Benefits
Gives more professional announcements and removes repetition. Excellent for Retail Outlets.
5.9.2 Required Software and Hardware
• SV8100 R5 Software
• BE110867, LK-SYS-V5000 Enhancements-LIC, (0034)
5.9.3 Training Course Required
• If SV8100 trained no further training required.
No new PRG CMD’s.
VRS message and Paging groups must be set as required.
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 33 of 36
6. SOFTWARE AND HARDWARE
The following are new Software and Hardware items released with SV8100 R5 Software:
Code Description Comments
New Software/Licenses
BE110867 LK-SYS-V5000
Enhancements-LIC
SV8100 Advanced Features License
BE110869 LK-SYS-ACD-
SKILLBASE-LIC Skill Based Routing license for use with InACD
BE110868 LK-SYS-XMLPro-
LIC
XMLPro license for partnered applications to retrieve/set
SV8100 configuration data
N/A SV8100 R5.01 New Version of SV8100 software (R5) containing items
listed within this document
N/A PC Pro 5.0.0 Pc Programming Tool for use with R5 System software
N/A 1st Party TSP 32
Bit
1st
Party TAPI Driver 32 bit
N/A 1st Party TSP 64
Bit
1st
Party TAPI Driver 64 bit
N/A 3rd
Party TSP 32
Bit
3rd
Party TAPI Driver 32 bit
N/A 3rd
Party TSP 32
Bit
3rd
Party TAPI Driver 64 bit
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 34 of 36
7. TECHNICAL DOCUMENTATION
The following Items have added/revised:
Description Revision
SV8100 System Hardware Manual (English) 4.0
SV8100 Features and Specification Manual 5.0
SV8100 Licensing Manual 1.5
SV8100 Hotel Manual 5.0
SV8100 VoIP Manual 5.0
SV8100 InMail System Guide 5.0
SV8100 MyCalls Installation Guide 3.0.0.0 (1.6)
SV8100 MyCalls CC Installation Guide 3.0.0.0 (1.4)
SV8100 MyCalls Enterprise Installation Guide 3.0.0.0 (1.2)
SV8100 ACD Manual 3.0
SV8100 Configuration Guide 2.0
SV8100 CTI Installation Manual 1.04a
SV8100 Gigabit PoE Manual 3.0
SV8100 Netlink QoS Example 1.0
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 35 of 36
8. TECHNICAL COURSES
The following courses have been added:
Description No. of Days
SV8100 R5 Update Training 2hrs
Copyright 2010 NEC Unified Solutions B.V. Exclusively for use by NEC Unified channel partners All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 36 of 36
9. DOCUMENT HISTORY
Date Issue Changes
25/01/11 1 First Release
18/02/11 2 Amended IP DECT 2nd
Call waiting