refresh wall fixture assembly instructions included in ... · f5 f4 1 1 1 power brick back mounting...

Refresh Wall FixtureAssembly Instructions

[email protected]

678-872-0082

www.retailone.com

INCLUDED IN THIS KIT

Part QTY. Description

Back Panel1A

A

BC

C

D

212

Light Arm

Light CordE 1 Power CordF 1 Tablet/Mount KitG 1H 1I 1J 12K 4

Printed Styrene Header

Light Bar Housing

Hardware KitBase Cabinet AssemblyShelf BracketsShelves

B DE

G

I

J

K

1

INCLUDED IN THE HARDWARE KIT


Butterfly Anchor4H1

H8

H6

H2H3

H1

H4

282

Grommet

Small Machine ScrewH5 4 4” Long Wood ScrewsH6 4 Fast CapH7 4 Standoff SpacersH8 4 Standoff Puck Fronts

Wood Screws

H7

H4

H2H5

H3

NOTE: TOOLS REQUIRED! This assembly will require a level, a pencil, a drill, a hammer, a Phillips #2 screwdriver, and a Phillips #1 screw driver. Needle-nose pliers may be used, but are not necessary.

2


[email protected]

678-872-0082

www.retailone.com

ITEMS NEEDED FROM THE TABLET/MOUNT KIT


Tablet1F1

F3

F2

F2F3

F5

F4

111

Power Brick

Back Mounting BracketF5 1 Front Mounting BracketF6 1 Tablet GraphicF7 4 Screws from Blister Packet E

Power Cord

F4

F7

F1

F6

3


[email protected]

678-872-0082

www.retailone.com

NOTE: Other items may be included in the boxes, but are not needed to complete the installation.

There are two power cords included, please use the American Three Prong Cord.

Locate the 4 anchor holes on the back panel, and use a pencil to Mark Wall for Butterfly Anchors (H1) by running the pencil through the anchor holes until it touches the wall.

Move the Back Panel (A) away from the wall.

Install Butterfly Anchors (H1): a. Use a drill to pre-drill a hole in the wall that is slightly narrower than the Butterfly Anchor (H1) at one of the marked locations. b. Fold the wings of the Butterfly Anchor (H1) in the middle to make it possible to fit into the pre-drilled hole. c. Press the Butterfly Anchor (H1) into the pre drilled hole. The Butterfly Anchor (H1) will expand behind the wall. d. Lightly tap the Butterfly Anchor (H1) with a hammer to ensure it is flush against the wall. There should be no gaps around the Butterfly Anchor (H1) if installed properly. e. Repeat in the other three marked locations.

4


[email protected]

678-872-0082

www.retailone.com

Place Back Panel (A) in position against a wall. Level the unit by turning the leveling feet to raise or lower one side of the unit. A pair of pliers may be used to do this, but are not necessary. Use a level to determine if the desired affect is acheived.

5


[email protected]

678-872-0082

www.retailone.com

Run one Light Arm (B) through the larger hole toward the top of Back Panel (A) so that the tube and its opening face forward and the back plate sits against the back face of the Back Panel (A) in a vertical position.

Place a Grommet (H2) around the front of the Light Arm (B) and press against the front surface of the Back Panel (A). This locates the Light Arm (B) in the center of its hole on the Back Panel (A).

Ensuring the back plate of the Light Arm (B) is in the vertical position, screw the Light Arm (B) in place using a drill, and two Wood Screws (H3) inserted through the slots of the Light Arm (B) back plate.

Repeat steps 4, 5 and 6 for the second Light Arm (B).

Using a Phillips #1 screwdriver, remove the three screws securing the end-cap of the Light Bar Housing (C) . Remove the end cap and set aside with the three screws.

Repeat to remove the second Light Bar Housing (C) endcap.

6


[email protected]

678-872-0082

www.retailone.com

Run Light Cord (D) through the Light Arm (B) from the backside of the Back Panel (A) through the front of the Light Arm (B). The Light Cord D should then pass through the Locating hole on the corresponding side of the Light Bar Housing (C) and plug into the side of the LED light bar itself. When completing this step the female end of Light Cord (D) should be passed through the front on the right side (when facing the front of the unit) and the male end should be passed through the front on the le� side (when facing the front of the unit).

Slide Light Arm (B) into the top channel of Light Bar Housing (C) aligning the Arm over the cord-locating hole through which Light cord (D) has already been thread. Secure in place using a small machine screw (H4).

Reattach Light Bar Housing (C) end cap using the 3 screws originally removed and a #1 Phillip’s head screwdriver.

Repeat steps 8-10 for the second side of the Light Bar Assembly.

NOTE: Four units may share a power source.

Every fourth unit will need to plug into a power outlet using a Power Cord (E). In this case a Power Cord (E) plugs into the backside of Light cord (D) on the le� back side of the fixture’s Back Panel (A).

8

9

10

11

7


[email protected]

678-872-0082

www.retailone.com

A second Light cord (D) should plug into the already installed Light cord (D) on the back right side of the unit. This new Light Cord (D) will plug into the back of the le� Light Cord (D) of the next unit, creating a chain of up to four units.

NOTE: If this fixture is the last in a set of four this step should be omitted.

If a Tablet (F1) is being used on this unit, place Power Brick (F2) in the Velcro strap provided on the bottom backside of the Back Panel (A. Run Power Cord (F3) to the Power Brick (F2) and the 2mm Cord attached to the Power Brick (F2) through the hole in the Back Panel (A) so that it is hanging from the front side.

Place the Back Mounting Bracket (F4) over the Back Panel (A) hole that the Power Brick (F2) Cord was thread through, so that the back plate is vertical and the notch on the front of the bracket is facing up creating a U. Screw into place through the two screw holes (top and bottom) using Wood Screws (H3).

15Slide the Front Mounting Bracket (F5) onto the front of the Back Mounting Bracket (F4) ensuring it is firmly seated in the aforementioned notch. Use the screw at the base to the Back Mounting Bracket (F4) to level the Front Mounting Bracket (F5).

Remove Front Mounting Bracket (F5).

14

12

13

15

NOTE: IF A TABLET IS NOT BEING USED SKIP TO STEP 21

8


[email protected]

678-872-0082

www.retailone.com

Place the Tablet (F1) face down on a clean surface. Place the Tablet Graphic (F6) face down on the back of t Tablet (F1). Place the Front Mounting Bracket (F5) face down on the back of the Tablet Graphic (F6). Ensure that the tops of all three pieces are oriented in the same direction. Use Screws from Blister Packet E (F7) included in the Tablet box to secure the Front Mounting Bracket (F5), through the Tablet Graphic (F6) to the Tablet (F1).

Pass the Power Brick (F2) 2mm cord through the hole in the Tablet Graphic (F6), and insert the jack into the Tablet (F1) on the bottom right side.

NOTE: Needle nose pliers may aid in the process but are not necessary.

Move the Tablet Assembly into place by sliding the Front Mount-ing Bracket (F5) back onto the Back Mounting Bracket (F4) ensuring it (F5) is securely seated in the notch of the Back Mounting Bracket (F4) . Tighten the screw on side of the Back Mounting Bracket (F4) to lock the Tablet Assembly in place.

Plug both the Tablet (F1) and the Light Bar (C) into the desired power outlet. An extension cord may be required.

18

16

17

19

9


[email protected]

678-872-0082

www.retailone.com

Place Back Panel (A) back against the wall in the original location.

Use a drill to screw a 4” Long Wood Screw (H5) through one of the locator holes and preplaced Butterfly Anchor (H1).

Repeat for the other three locator holes, securing the Back Panel (A) to the wall.

Peel the paper backing from the adhesive on the back of the Fast Caps (H6). Apply Fast Cap (H6) to the front of the Back Panel (A) to cover the four locator holes and the four 4” Long Wood Screws (H5).

Screw 4 header Standoff Spacers (H7) onto the preinstalled threads at the top of the Back Panel (A).

Align the Holes of the Printed Styrene Header (G) with those of the Standoff Spacers (H7). Secure in place by hand screwing the Standoff Puck Fronts (H8) through the Header (G) into the Standoff Spacers (H7).

22

20

21

23

10


[email protected]

678-872-0082

www.retailone.com

Place Base Cabinet Assembly (I) in front of the Back Panel (A) ensuring it is centered and flush. Turn the leveling legs to make sure the Base Cabinet Assembly (I) top surface is flat. Ensure the desired results are echeived by using a level.

Insert three Shelf Brackets (J) into three recessed standards on Back Panel (A) at corresponding heights to create a level Shelf (K). Press down on the back of the Shelf Brackets (J) to make sure that the teeth of the Shelf Brackets (J) drop into place and are firmly seated.

Slide a Shelf (K) into the back slots of the three installed Shelf Brackets (J) and rest the front of shelf on the rubber gaskets located on the Shelf Bracket (J) arms.

Repeat Steps 28-29 until all desired shelves are placed.

The unit is now ready to merchandise!

26

24

25

NOTE: You may decide to secure the Base Cabinet Assembly (I) to the Back Panel (A), using woodscrews, to prevent movement in field.

NOTE: Consult OMG for so�ware startup if using tablet

refresh wall fixture assembly instructions included in ... · f5 f4 1 1 1 power brick back mounting...

Documents