ref flexi trns param

WCDMA RAN and I-HSPA, Rel. RU30, Operating Documentation, Issue 05

Flexi Transport Module Parameters

DN70577885

Issue 03FApproval Date 2011-12-16

Confidential

2 DN70577885Issue 03F


Id:0900d805808eaf4dConfidential

The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation.

The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document.

Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTA-TION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDI-RECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT.

This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only.

Copyright © Nokia Siemens Networks 2011. All rights reserved

f Important Notice on Product SafetyThis product may present safety risks due to laser, electricity, heat, and other sources of danger.

Only trained and qualified personnel may install, operate, maintain or otherwise handle this product and only after having carefully read the safety information applicable to this product.

The safety information is provided in the Safety Information section in the “Legal, Safety and Environmental Information” part of this document or documentation set.

The same text in German:

f Wichtiger Hinweis zur Produktsicherheit Von diesem Produkt können Gefahren durch Laser, Elektrizität, Hitzeentwicklung oder andere Gefahrenquellen ausgehen.

Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch geschultes und qualifiziertes Personal unter Beachtung der anwendbaren Sicherheits-anforderungen erfolgen.

Die Sicherheitsanforderungen finden Sie unter „Sicherheitshinweise“ im Teil „Legal, Safety and Environmental Information“ dieses Dokuments oder dieses Dokumentations-satzes.

DN70577885 3



Table of contentsThis document has 470 pages.

Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

2 A2NE Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 532.1 aal2NodeId (AAL2 Node Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

3 A2ST Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543.1 AAL2EndAddress (AAL2 End Address). . . . . . . . . . . . . . . . . . . . . . . . . 543.2 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543.3 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 553.4 aal2sigTTPId (AAL2 Signalling Link Identifier). . . . . . . . . . . . . . . . . . . . 563.5 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . 573.6 stcAlarmEnable (Signalling Transport Converter Alarm Enable) . . . . . . 583.7 unitNumber (Unit Number). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

4 A2UT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 614.1 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 614.2 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 614.3 aal2pathTTPId (AAL2 User Path Identifier) . . . . . . . . . . . . . . . . . . . . . . 624.4 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . 644.5 pid (Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 644.6 queue2Weight (Weight of AAL2 user path queue Q2). . . . . . . . . . . . . . 654.7 queue3Weight (Weight of AAL2 user path queue Q3). . . . . . . . . . . . . . 664.8 queue4Weight (Weight of AAL2 user path queue Q4). . . . . . . . . . . . . . 674.9 unitNumber (Unit Number). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

5 ACCP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 695.1 atmAccessProfileId (ATM Access Profile Identifier). . . . . . . . . . . . . . . . 695.2 egressBandwidth (Egress Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . . 695.3 ingressBandwidth (Ingress Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . 71

6 AMGR Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 736.1 amgrId (Account Manager Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . 736.2 ldapConnectionType (LDAP Server TLS access mode) . . . . . . . . . . . . 736.3 primaryLdapPort (Port Number of Primary LDAP Server) . . . . . . . . . . . 746.4 primaryLdapServer (IP address of Primary LDAP Server) . . . . . . . . . . 75

7 ANBA Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 777.1 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 777.2 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 777.3 interfaceNumber (Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 787.4 nbapTTPId (Upper Layer Path Identifier). . . . . . . . . . . . . . . . . . . . . . . . 797.5 nbapType (Upper Layer Connection Type) . . . . . . . . . . . . . . . . . . . . . . 807.6 unitNumber (Unit Number). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

8 BFD Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 838.1 bfdActivation (BFD session activation flag) . . . . . . . . . . . . . . . . . . . . . . 83

4 DN70577885



8.2 bfdAdminUp (BFD session admin down state control) . . . . . . . . . . . . . . 848.3 bfdDestAddress (Destination IP address for the BFD session) . . . . . . . 858.4 bfdDetectMult (BFD session packets lost detection time multiplier) . . . . 868.5 bfdGrp (BFD group reference) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 878.6 bfdId (BFD session identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 888.7 bfdSourceIpAddr (Source IP address for the BFD session) . . . . . . . . . . 898.8 bfdSourceUdpPort (UDP source port of the BFD session) . . . . . . . . . . . 908.9 bfdType (BFD session type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 918.10 desMinTxInt (Desired minimum BFD control word transmit interval) . . . 928.11 function (BFD session function definition). . . . . . . . . . . . . . . . . . . . . . . . 938.12 reqMinRxInt (Required minimum BFD control word receive interval) . . . 94

9 BFDGRP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 969.1 bfdGrpId (BFD Group Identifier ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

10 CCFA Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9710.1 atmFabricId (ATM Fabric Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9710.2 ubrPlusEnabled (UBR+ Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9810.3 vccBundleEnabled (VCC Bundle Enabling Flag) . . . . . . . . . . . . . . . . . . 99

11 CERTH Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10011.1 btsCertificateUpdateTime (BTS certificate update time). . . . . . . . . . . . 10011.2 caCertificateUpdateTime (CA certificate update time) . . . . . . . . . . . . . 10011.3 caSubjectName (CMP server subject name) . . . . . . . . . . . . . . . . . . . . 10111.4 certhId (Certification Handler Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 10211.5 cmpServerIpAddress (CMP Server IP Address) . . . . . . . . . . . . . . . . . . 10311.6 cmpServerPort (CMP Server Port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10411.7 crServerIpAddress (CR Server IP Address) . . . . . . . . . . . . . . . . . . . . . 10511.8 crServerPort (CR Server Port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10511.9 crlUpdatePeriod (Certificate Revocation List update period) . . . . . . . . 106

12 CESIF Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10812.1 cesMinUDPPort (CES over PSN source port value range) . . . . . . . . . 10812.2 cesifId (CES over PSN interface identifier) . . . . . . . . . . . . . . . . . . . . . . 109

13 CESPW Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11013.1 administrativeState (Administrative state). . . . . . . . . . . . . . . . . . . . . . . 11013.2 cesPWid (CES over PSN Pseudowire Identifier) . . . . . . . . . . . . . . . . . 11113.3 dscp (DSCP value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11213.4 framesNumber (Number of frames per CESoPSN packet) . . . . . . . . . 11313.5 jitterBufferSize (Jitter Buffer Size) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11413.6 payloadTimeslots (Payload timeslots of TDM frame) . . . . . . . . . . . . . . 11513.7 remoteUDPPort (Remote UDP port number for CES over PSN) . . . . . 117

14 CESPWT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11914.1 cesPWTid (CES over PSN pseudowire tunnel identifier) . . . . . . . . . . . 11914.2 destIpAddress (Destination IP address) . . . . . . . . . . . . . . . . . . . . . . . . 119

15 ETHLK Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12115.1 acceptableFrameTypes (Switch Port Acceptable Frame Types) . . . . . 12115.2 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . . 122

DN70577885 5



15.3 ethLinkId (Ethernet Link Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12315.4 flushFdbOnLos (Flush fdb on LOS mode) . . . . . . . . . . . . . . . . . . . . . . 12515.5 l2BurstSize (Switch Port egress Shaper Burst Size) . . . . . . . . . . . . . . 12615.6 l2IngressRate (Switch Port ingress RateLimiter Rate ) . . . . . . . . . . . . 12715.7 l2ShaperRate (Switch Port egress Shaper Rate) . . . . . . . . . . . . . . . . 13015.8 l2VlanIdList (Switch Port VLAN Member List) . . . . . . . . . . . . . . . . . . . 13315.9 highValue (Switch Port VLAN Member Range High Value). . . . . . . . . 13415.10 lowValue (Switch Port VLAN Member Range Low Value). . . . . . . . . . 13515.11 linkOAMEnabled (Link OAM enabling flag) . . . . . . . . . . . . . . . . . . . . . 13615.12 linkOAMProfile (Link OAM profile reference) . . . . . . . . . . . . . . . . . . . . 13715.13 macAddr (MAC address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13815.14 portDefaultPriority (Switch Port Default VLAN Priority) . . . . . . . . . . . . 13815.15 portDefaultVlanId (Switch Port Default VLAN Identifier) . . . . . . . . . . . 13915.16 speedAndDuplex (Speed and Duplex flag) . . . . . . . . . . . . . . . . . . . . . 14015.17 synchEMode (Synchronous ethernet mode) . . . . . . . . . . . . . . . . . . . . 142

16 FRLI Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14316.1 afrLinkInterfaceId (Fractional Interface Identifier) . . . . . . . . . . . . . . . . 14316.2 afrTimeSlotSequence (ATM over Fractional JT1 Time Slot Sequence) 14416.3 interfaceNumber (Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 14616.4 unitNumber (Unit Number). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

17 FTM Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14817.1 adaptationVersionMajor (Adaptation Version Major) . . . . . . . . . . . . . . 14817.2 ftmId (BTS Transport Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14817.3 locationName (Location Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14917.4 softwareReleaseVersion (Software Release Version) . . . . . . . . . . . . . 15017.5 systemTitle (System Title) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15117.6 userLabel (User Label) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152

18 IAIF Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15318.1 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15318.2 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15318.3 atmIfNetId (ATM IP Net Interface Identifier). . . . . . . . . . . . . . . . . . . . . 15418.4 destIpAddr (Destination IP Address) . . . . . . . . . . . . . . . . . . . . . . . . . . 15618.5 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 15718.6 unitNumber (Unit Number). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158

19 IEIF Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15919.1 cir (Committed information rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15919.2 confCost (OSPF configured interface cost) . . . . . . . . . . . . . . . . . . . . . 16019.3 helloInterval (OSPF keepalive message transmission interval). . . . . . 16119.4 ieifId (Identifier of the plain Ethernet interface) . . . . . . . . . . . . . . . . . . 16219.5 interfaceArea (OSPF interface area) . . . . . . . . . . . . . . . . . . . . . . . . . . 16319.6 ipAddr (IP Address Info in the Transport Network) . . . . . . . . . . . . . . . 16419.7 localIpAddr (Local Address of the IP Interface) . . . . . . . . . . . . . . . . . . 16519.8 netmask (IP Network Mask). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16619.9 mtu (Maximum transfer unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16619.10 mtuMismatchDetection (MTU mismatch detection in use). . . . . . . . . . 167

6 DN70577885



19.11 ospfWithBfd (OSPF uses additionally BFD) . . . . . . . . . . . . . . . . . . . . . 16819.12 proxyArpIpAddrList (List of proxy ARP IP addresses for this interface.). . .

16919.13 qosEnabled (QOS traffic priorisation enabling flag) . . . . . . . . . . . . . . . 17019.14 retransInterval (OSPF LSA retransmission interval) . . . . . . . . . . . . . . . 17119.15 routerDeadInterval (OSPF router read interval) . . . . . . . . . . . . . . . . . . 17219.16 sbs (Shaper burst size) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17319.17 sbsTotal (Total shaper burst size). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17419.18 shapedBandwidth (Shaped Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . 17519.19 sir (Shaper information rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17619.20 sirTotal (Total shaper information rate). . . . . . . . . . . . . . . . . . . . . . . . . 17719.21 trafficPathShapingEnable (Traffic path shaping enabling flag) . . . . . . . 17819.22 transmitDelay (OSPF packet transmission delay) . . . . . . . . . . . . . . . . 18019.23 upperLayerShaping (Upper Layer Shaping Enabled Flag) . . . . . . . . . . 18019.24 vlanEnabled (Vlan Enabled flag). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18119.25 vlanId (Vlan ID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182

20 IHCP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18420.1 client_identifier (Entry set for DHCP clients identified by a system name) .

18420.2 dhcpClientIdentifier (DHCP Client Identifier). . . . . . . . . . . . . . . . . . . . . 18420.3 dhcpFixedIpAddress (DHCP Fixed IP Address) . . . . . . . . . . . . . . . . . . 18520.4 dhcpAccessId (DHCP Server Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 18620.5 hardware_identifier (Entry set of DHCP clients identified by a MAC ad-

dress) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18720.6 dhcpFixedIpAddress (DHCP Fixed IP Address) . . . . . . . . . . . . . . . . . . 18820.7 dhcpHardwareIdentifier (DHCP Hardware Identifier) . . . . . . . . . . . . . . 18920.8 range_identifier (DHCP server IP address pool). . . . . . . . . . . . . . . . . . 19020.9 dhcpRangeEnd (DHCP Range End IP Address) . . . . . . . . . . . . . . . . . 19020.10 dhcpRangeStart (DHCP Range Start IP Address) . . . . . . . . . . . . . . . . 191

21 IMAG Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19321.1 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . . 19321.2 imaGroupId (IMA group identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19421.3 imaVersionId (IMA Version Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 19521.4 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 19621.5 interfaces (Physical interface list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19621.6 minNumLinks (Minimum Number of Links) . . . . . . . . . . . . . . . . . . . . . . 19721.7 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198

22 INTP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20022.1 ntpAccessId (NTP Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20022.2 ntpServers (List of NTP Server IP Addresses) . . . . . . . . . . . . . . . . . . . 200

23 IPNO Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20223.1 bfdHoldUpTime (BFD throttle time for re-installing protection routes) . 20223.2 btsId (BTS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20323.3 btsIpAddr (Base Station IP Address) . . . . . . . . . . . . . . . . . . . . . . . . . . 20323.4 cPlaneIpAddress (Control-plane application IP address) . . . . . . . . . . . 20423.5 cesopsnIpAddress (CES over PSN application IP address) . . . . . . . . . 206

DN70577885 7



23.6 disableFtp (Disable FTP server) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20723.7 flexBusIpAddr (Public IP Address of Flexbus Part of BTS) . . . . . . . . . 20823.8 fpLocalUdpPort (Local UDP port for small packets multiplexing) . . . . 20823.9 fpMuxAmount (Maximum amount of small packets that can be multiplexed)

20923.10 fpMuxDelay (Small packets multiplexing delay time). . . . . . . . . . . . . . 21023.11 fpRemoteUdpPort (Remote UDP port for small packets multiplexing) 21123.12 ftmIpAddr (Flexi Transport Module IP Address). . . . . . . . . . . . . . . . . . 21223.13 ftmNetmask (Netmask of the public IP address) . . . . . . . . . . . . . . . . . 21323.14 iHSPAAdapterCommissioningParameter (I-HSPA adapter initial commis-

sioning parameters) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21423.15 iHSPAmode (I-HSPA mode activation flag) . . . . . . . . . . . . . . . . . . . . . 21523.16 icmpResponseEnabled (Enable response to ICMP traffic) . . . . . . . . . 21523.17 ipNodeId (IP Node Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21623.18 linkOAMLoopbackSupport (Link OAM remote loopback discovery enabling

flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21723.19 mPlaneIpAddress (Management -plane application IP address). . . . . 21823.20 mtu (Maximum transfer unit of the BTS) . . . . . . . . . . . . . . . . . . . . . . . 21923.21 oamCir (Committed information rate for Service OAM messages) . . . 22023.22 oamTlvReply (Optional TLV message reply flag) . . . . . . . . . . . . . . . . 22123.23 omsTls (TLS usage towards the O&M system) . . . . . . . . . . . . . . . . . . 22223.24 ret1IpAddr (RET IP Address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22323.25 rncIpAddr (RNC IP Address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22423.26 sPlaneIpAddress (Synchronization-plane application IP address) . . . 22523.27 transportMode (BTS transport mode) . . . . . . . . . . . . . . . . . . . . . . . . . 22623.28 twampMessageRate (TWAMP initiator rate for sending messages) . . 22723.29 twampReflectorOn (TWAMP message response enabling flag) . . . . . 22823.30 twampReflectorPort (TWAMP reflector port number) . . . . . . . . . . . . . 22923.31 twampSourcePort (TWAMP source port number) . . . . . . . . . . . . . . . . 23023.32 uPlane2IpAddress (Second user-plane application IP address) . . . . . 23123.33 uPlane2IpInterface (Second user-plane application IP network interface)

23223.34 uPlaneIpAddress (User plane application IP address) . . . . . . . . . . . . 23323.35 uPlaneIpInterface (User-plane application IP network interface). . . . . 235

24 IPRM Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23724.1 RmExceptions (Restricted Mode Exception) . . . . . . . . . . . . . . . . . . . . 23724.2 sourceTwoDiscr (How is source two defined?) . . . . . . . . . . . . . . . . . . 23824.3 sourceTwoIpAddr (IP address for source two). . . . . . . . . . . . . . . . . . . 23924.4 sourceTwoNetMask (IP Subnet Mask) . . . . . . . . . . . . . . . . . . . . . . . . 24024.5 userLabel (User Label) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24124.6 iprmId (IP Restricted Mode Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 242

25 IPRT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24325.1 ipRoutingTableId (IP Routing Table Identifier). . . . . . . . . . . . . . . . . . . 24325.2 staticRoutes (List of static routes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24425.3 bfdId (BFD route protection session identifier). . . . . . . . . . . . . . . . . . . 24425.4 destIpAddr (Route destination IP address) . . . . . . . . . . . . . . . . . . . . . 24525.5 gateway (IP address of the next hop of the route) . . . . . . . . . . . . . . . . 246

8 DN70577885



25.6 netmask (Netmask of the destination IP address) . . . . . . . . . . . . . . . . 24725.7 preference (Preference value for the route) . . . . . . . . . . . . . . . . . . . . . 248

26 IVIF Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25026.1 cESoPSN (CES over PSN flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25026.2 cir (Committed information rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25126.3 confCost (OSPF configured interface cost) . . . . . . . . . . . . . . . . . . . . . 25226.4 helloInterval (OSPF keepalive message transmission interval) . . . . . . 25226.5 interfaceArea (OSPF interface area) . . . . . . . . . . . . . . . . . . . . . . . . . . 25326.6 localIpAddr (Local Address of the IP Interface) . . . . . . . . . . . . . . . . . . 25426.7 mtuMismatchDetection (MTU mismatch detection in use) . . . . . . . . . . 25526.8 netmask (IP network mask of the local IP address) . . . . . . . . . . . . . . . 25626.9 ospfWithBfd (OSPF uses additionally BFD) . . . . . . . . . . . . . . . . . . . . . 25726.10 proxyArpIpAddrList (List of proxy ARP IP addresses for this interface.). . .

25726.11 qosEnabled (QOS traffic priorisation enabling flag) . . . . . . . . . . . . . . . 25826.12 retransInterval (OSPF LSA retransmission interval) . . . . . . . . . . . . . . . 25926.13 routerDeadInterval (OSPF router read interval) . . . . . . . . . . . . . . . . . . 26026.14 sbs (Shaper burst size) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26126.15 sir (Shaper information rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26226.16 transmitDelay (OSPF packet transmission delay) . . . . . . . . . . . . . . . . 26326.17 vlanId (VLAN identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26426.18 vlanIfNetId (VLAN interface object identifier) . . . . . . . . . . . . . . . . . . . . 265

27 L2SWI Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26627.1 dscpMap (DSCP to priority queue map) . . . . . . . . . . . . . . . . . . . . . . . . 26627.2 dscp (DSCP value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26727.3 priorityQueue (Priority queue identifier) . . . . . . . . . . . . . . . . . . . . . . . . 26827.4 enableLayer2Switching (Ethernet Switch Enable) . . . . . . . . . . . . . . . . 26927.5 l2PriorityQueueWeight2 (Layer 2 switch member weight for priority queue

2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27027.6 l2PriorityQueueWeight3 (Layer 2 switch member weight for priority queue




6). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27327.10 portDefaultPriority (Switch Port Default VLAN Priority (internal Port)) . 27427.11 portDefaultVlanId (Switch Port Default VLAN Identifier (internal Port)) 27527.12 priorityQueueNonIP (Priority queue for non-IP frames) . . . . . . . . . . . . 27627.13 priorityQueuePcp0 (Priority queue for ethernet frames with VLAN PCP bits

0). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27727.14 priorityQueuePcp1 (Priority queue for ethernet frames with VLAN PCP bits



3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281

DN70577885 9



27.17 priorityQueuePcp4 (Priority queue for ethernet frames with VLAN PCP bits 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282




27.21 priorityQueueUntagged (Priority queue for untagged ethernet frames) 28627.22 qosClassification (QoS Classification Mode) . . . . . . . . . . . . . . . . . . . . 28727.23 switchId (Layer 2 Switch Object Identifier). . . . . . . . . . . . . . . . . . . . . . 28727.24 vlanAwareSwitch (VLAN Aware Switching Enable) . . . . . . . . . . . . . . . 288

28 OAMMA Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29028.1 assocId (Maintenance association identifier) . . . . . . . . . . . . . . . . . . . . 29028.2 maName (Name of the maintenance domain) . . . . . . . . . . . . . . . . . . . 29028.3 vlanId (VLAN identifier of the maintenance association) . . . . . . . . . . . 291

29 OAMMD Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29329.1 domainId (Maintenance domain identifier). . . . . . . . . . . . . . . . . . . . . . 29329.2 mdLevel (Level of the maintenance domain) . . . . . . . . . . . . . . . . . . . . 29329.3 mdName (Name of the maintenance domain) . . . . . . . . . . . . . . . . . . . 294

30 OAMMEP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29630.1 aisEnabled (AIS message transmission enabling flag) . . . . . . . . . . . . 29630.2 aisTxPeriod (AIS messages transmission period) . . . . . . . . . . . . . . . . 29630.3 ccmTxPeriod (Continuity Check Messages transmission period) . . . . 29730.4 enableCcm (Allow sending of CCM messages and reset CCM counters).

29830.5 ethernetPort (Ethernet link reference) . . . . . . . . . . . . . . . . . . . . . . . . . 29930.6 oammepId (Maintenance association endpoint identifier) . . . . . . . . . . 30030.7 remoteMepList (Remote maintenance association endpoints list). . . . 30130.8 macAddr (MAC address of the remote MEP) . . . . . . . . . . . . . . . . . . . 30230.9 mepId (Remote maintenance association endpoint identifier) . . . . . . . 30330.10 vlanPrio (VLAN PCP bits) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304

31 OAMPRF Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30531.1 activeMode (Link OAM operational mode at local peer) . . . . . . . . . . . 30531.2 alarmClearanceDelay (Link OAM Link Critical Event Alarm clearance de-

lay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30631.3 efEventThreshold (Errored Frame Event counting threshold) . . . . . . . 30631.4 efEventWindow (Errored Frame Event counting interval) . . . . . . . . . . 30731.5 efpEventThreshold (Errored Frame Period Event counting threshold) 30831.6 efpEventWindow (Errored Frame Period Event counting interval) . . . 30931.7 efssEventThreshold (Errored Frame Seconds Summary Event counting

threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31031.8 efssEventWindow (Errored Frame Seconds Summary Event counting in-

terval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31131.9 enableCcm (Allow sending of CCM messages and reset CCM counters).

31231.10 eventRepetition (OAM PDU message transmission rate) . . . . . . . . . . 313

10 DN70577885



31.11 eventSupport (Link OAM event support flag) . . . . . . . . . . . . . . . . . . . . 31431.12 linkLostTime (Link OAM link lost time) . . . . . . . . . . . . . . . . . . . . . . . . . 31531.13 loopBackTime (Link OAM loopback duration). . . . . . . . . . . . . . . . . . . . 31631.14 profileId (Profile instance identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . 31731.15 testFrameRate (Link OAM loopback test message rate) . . . . . . . . . . . 31831.16 testFrameSize (Link OAM loopback test message frame size) . . . . . . 318

32 OSPFV2 Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32032.1 confPref (OSPF routing preference value) . . . . . . . . . . . . . . . . . . . . . . 32032.2 ospfAreas (OSPF area list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32032.3 areaId (OSPF area identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32132.4 areaStub (OSPF area stub flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32232.5 ospfEnabled (OSPF enabling flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32332.6 ospfRouterId (OSPF router identification) . . . . . . . . . . . . . . . . . . . . . . . 32432.7 ospfV2Id (OSPF configuration identifier) . . . . . . . . . . . . . . . . . . . . . . . 32532.8 refBandwidth (Reference bandwidth for OSPF cost equal to 1) . . . . . . 32632.9 spfDelay (OSPF Shortest Path First recalculation delay) . . . . . . . . . . . 32732.10 spfHoldTime (OSPF Shortest Path First hold time) . . . . . . . . . . . . . . . 32732.11 spfMaxHoldTime (OSPF maximum Shortest Path First hold time). . . . 328

33 P3LP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33033.1 acFieldCompressionOn (Access Control Field Compression flag) . . . . 33033.2 fcsFieldLength (Frame Check Sequence field size) . . . . . . . . . . . . . . 33133.3 magicNumberOn (Magic number flag) . . . . . . . . . . . . . . . . . . . . . . . . . 33133.4 mruSize (Maximum Receive Unit (MRU) size) . . . . . . . . . . . . . . . . . . . 33233.5 p3lpId (PPP link identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33433.6 protocolFieldCompressionOn (Protocol Field Compression flag) . . . . . 335

34 P3ML Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33734.1 administrativeState (Administrative state of the PPP multi-link) . . . . . . 33734.2 endPointDiscriminatorType (Endpoint discriminator type) . . . . . . . . . . 33834.3 interfaces (Physical interface list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33834.4 mpFragmentSize (Fragment size in egress direction) . . . . . . . . . . . . . 33934.5 mrruSize (Maximum Receive Reconstructed Unit (MRRU) size) . . . . . 34034.6 netmask (Netmask of the IP address of the PPP endpoint) . . . . . . . . . 34234.7 p3mlId (PPP multi-link identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34334.8 p3pIpAddr (PPP endpoint IP address) . . . . . . . . . . . . . . . . . . . . . . . . . 34334.9 shortSeqNrOn (Short sequence numbering flag) . . . . . . . . . . . . . . . . . 34434.10 ts16Excluded (Is timeslot TS16 excluded) . . . . . . . . . . . . . . . . . . . . . . 345

35 P3SL Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34735.1 administrativeState (Administrative state of the PPP link) . . . . . . . . . . 34735.2 interface (Physical interface list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34735.3 netmask (Netmask for the IP address of the PPP endpoint) . . . . . . . . 34835.4 p3pIpAddr (PPP endpoint IP address) . . . . . . . . . . . . . . . . . . . . . . . . . 34935.5 p3slId (PPP single link object instance identifier) . . . . . . . . . . . . . . . . . 35035.6 ts16Excluded (Is timeslot TS16 excluded) . . . . . . . . . . . . . . . . . . . . . . 351

36 PPTT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35336.1 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . . 353

DN70577885 11



36.2 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 35336.3 pdhLbo (PDH Line Build Out) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35436.4 pdhLineType (PDH Line Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35536.5 pdhPSTTPId (PDH Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 35736.6 unitNumber (Unit Number). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359

37 PWMP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36037.1 bfdAdminUp (BFD actual session administration flag). . . . . . . . . . . . . 36037.2 bfdEnable (Bidirectional Forwarding Enabled). . . . . . . . . . . . . . . . . . . 36037.3 cellsConcatUl (Uplink Concatenation Factor.) . . . . . . . . . . . . . . . . . . . 36137.4 ctpList (Set of registered vcCTPs.) . . . . . . . . . . . . . . . . . . . . . . . . . . . 36237.5 labelDl (Downlink MPLS Header) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36337.6 labelUl (Uplink MPLS Header) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36437.7 perHopBehaviour (Per hop behaviour DiffServ) . . . . . . . . . . . . . . . . . 36437.8 pkTimer (Packetization Timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36637.9 pwMplsId (MPLS Pseudowire Identifier) . . . . . . . . . . . . . . . . . . . . . . . 367

38 PWNE Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36838.1 bfdTimer (BFD Timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36838.2 bfdDetectMult (Maximum allowed number of lost control packets for BFD)

36838.3 desiredMinTxIntvl (Desired Minimum Transmit Interval) . . . . . . . . . . . 36938.4 requiredMinRxIntvl (Required Minimum Receive Interval). . . . . . . . . . 37038.5 cwEnable (Control Word Enable). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37138.6 pwNeId (Pseudowire Network Element Identifier) . . . . . . . . . . . . . . . . 372

39 PWTIP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37339.1 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . . 37339.2 attachedPWList (Attached Pseudo-Wires List) . . . . . . . . . . . . . . . . . . 37339.3 pwTipId (Pseudowire Tunnel IP Identifier) . . . . . . . . . . . . . . . . . . . . . . 37439.4 remoteIpv4Addr (Remote IPv4 Address) . . . . . . . . . . . . . . . . . . . . . . . 375

40 QOS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37740.1 perHopBehaviourWeightList (Per Hop Behaviour Weight List) . . . . . . 37740.2 assuredForwardingClass1 (Assured Forwarding Class 1 Weight Value) .

37840.3 assuredForwardingClass2 (Assured Forwarding Class 2 Weight Value) .



38040.6 bestEffort (Best Effort Weight Value) . . . . . . . . . . . . . . . . . . . . . . . . . . 38140.7 qosId (Quality of Service Configuration Identifier) . . . . . . . . . . . . . . . . 38240.8 trafficTypesMap (Quality of Service mapping table) . . . . . . . . . . . . . . 38240.9 dscpList (Differentiated Services Code Point list) . . . . . . . . . . . . . . . . 38340.10 pHB (Per Hop Behaviour) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38440.11 trafficType (Traffic type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38540.12 vlanPrio (Vlan priority flag). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387

41 SDHIF Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389

12 DN70577885



41.1 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . . 38941.2 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 39041.3 laserMode (Laser Mode). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39041.4 rdiOnExcessiveBer (Remote Defect Indication On Excessive Bit Error Ra-

tio) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39141.5 sdhifId (SDH Interface Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39241.6 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39341.7 xmtTraceId_HP (Sent Trace Identifier (J1, HOP)) . . . . . . . . . . . . . . . . 39441.8 xmtTraceId_RS (Sent Trace Identifier (J0, RS)) . . . . . . . . . . . . . . . . . . 394

42 STPG Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39642.1 ssmSelExt2M (SSM Selection with external 2.048 MHz) . . . . . . . . . . . 39642.2 ssmSelPDH (SSM Selection with TDM) . . . . . . . . . . . . . . . . . . . . . . . . 39742.3 ssmSelSyncE (SSM Selection with SyncE) . . . . . . . . . . . . . . . . . . . . . 39842.4 ssmTxUntagged (Send SSM message frames untagged) . . . . . . . . . . 39942.5 ssmType (SSM support network standard). . . . . . . . . . . . . . . . . . . . . . 39942.6 synchERegenOn (Activate the synchronous ethernet regenerator function)

40042.7 synchroSourceList (The synchronization sources of the BTS) . . . . . . . 40142.8 clockProtocol (Protocol of the clock source) . . . . . . . . . . . . . . . . . . . . . 40242.9 interfaceNumber (Interface number). . . . . . . . . . . . . . . . . . . . . . . . . . . 40342.10 priority (Clock source priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40542.11 ssmAcceptanceLevel (SSM defined value) . . . . . . . . . . . . . . . . . . . . . 40542.12 ssmEnabled (SSM enabling flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40642.13 ssmTimeout (SSM message timeout). . . . . . . . . . . . . . . . . . . . . . . . . . 40742.14 unitNumber (Unit number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40842.15 timingGenPgId (Synchronisation Protection Group Identifier) . . . . . . . 409

43 SYNC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41143.1 syncId (Clock Synchronization Configuration Identifier) . . . . . . . . . . . . 411

44 TCTT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41244.1 interfaceNumber (Interface number). . . . . . . . . . . . . . . . . . . . . . . . . . . 41244.2 tcAdaptorTTPId (ATM Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . 41344.3 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414

45 TMPAR Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41545.1 cacCommittedBitRate (CAC Committed Bit Rate) . . . . . . . . . . . . . . . . 41545.2 dcnCommittedBitRate (DCN Committed Bit Rate) . . . . . . . . . . . . . . . . 41745.3 externalNATIpAddress (External NAT IP Address) . . . . . . . . . . . . . . . 41845.4 farEndSctpSubnetIpAddress (Far End SCTP Subnet IP Address ) . . . 41945.5 farEndSctpSubnetMask (Far End SCTP Subnet Mask) . . . . . . . . . . . . 42045.6 minSCTPPort (Minimum SCTP port number) . . . . . . . . . . . . . . . . . . . . 42045.7 minUDPPort (Minimum UDP port number) . . . . . . . . . . . . . . . . . . . . . . 42145.8 signallingCommittedBitRate (Signalling Committed Bit Rate). . . . . . . . 42245.9 tmparId (TMPAR Object Instance Identifier) . . . . . . . . . . . . . . . . . . . . . 423

46 TOPIK Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42546.1 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . . 42546.2 logMeanSyncValue (Log mean synchronization value) . . . . . . . . . . . . 425

DN70577885 13



46.3 masterIpAddr (IP Address of the ToP master). . . . . . . . . . . . . . . . . . . 42646.4 topId (Timing Over Packet Configuration Identifier). . . . . . . . . . . . . . . 427

47 TRDE Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42947.1 atmTrafficDescriptorId (Traffic Descriptor Identifier) . . . . . . . . . . . . . . 42947.2 conformanceDefinition (Conformance Definition) . . . . . . . . . . . . . . . . 42947.3 minDesiredCellRate (Minimum Desired Cell Rate) . . . . . . . . . . . . . . . 43047.4 peakCellRate (Peak Cell Rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43147.5 ubrShare (UBR Share). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43247.6 userLabel (User Label) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433

48 TWAMP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43548.1 administrativeState (Lock or unlock a TWAMP session) . . . . . . . . . . . 43548.2 destIpAddress (TWAMP session destination IP address) . . . . . . . . . . 43648.3 destPort (TWAMP session destination port) . . . . . . . . . . . . . . . . . . . . 43748.4 dscp (DSCP value for TWAMP message transmission) . . . . . . . . . . . 43748.5 messageSize (TWAMP initiator message size) . . . . . . . . . . . . . . . . . . 43848.6 plrAlarmThreshold (Packet loss ratio alarm threshold) . . . . . . . . . . . . 43948.7 rttAlarmThreshold (Round-trip-time alarm threshold) . . . . . . . . . . . . . 44048.8 sourceIpAddress (TWAMP initiator messages source IP address) . . . 44148.9 twampId (TWAMP session identifier). . . . . . . . . . . . . . . . . . . . . . . . . . 442

49 UNIT Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44449.1 enableRP301Interface (Enable RP3-01 interface). . . . . . . . . . . . . . . . 44449.2 unitId (Unit Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44449.3 unitTypeActual (Installed hardware unit type) . . . . . . . . . . . . . . . . . . . 44549.4 unitTypeExpected (Expected hardware unit type) . . . . . . . . . . . . . . . . 447

50 VCCT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45050.1 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45050.2 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45050.3 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 45150.4 trafficDescriptorId (Traffic Descriptor Pointer) . . . . . . . . . . . . . . . . . . . 45250.5 unitNumber (Unit Number). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45350.6 vcCTPId (Virtual Channel Identifier (VCI)) . . . . . . . . . . . . . . . . . . . . . . 454

51 VCTT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45551.1 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45551.2 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45551.3 aalProfilePtr (ATM Adaptation Layer (AAL) Profile Pointer) . . . . . . . . 45651.4 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 45751.5 unitNumber (Unit Number). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45851.6 vcTTPId (Virtual Channel Trail Termination Point Identifier) . . . . . . . . 459

52 VPCT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46152.1 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46152.2 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 46152.3 trafficDescriptorId (Traffic Descriptor Pointer) . . . . . . . . . . . . . . . . . . . 46252.4 unitNumber (Unit Number). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46352.5 vpCTPId (Virtual Path Identifier (VPI)) . . . . . . . . . . . . . . . . . . . . . . . . . 464

14 DN70577885



53 VPTT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46653.1 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46653.2 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 46653.3 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46753.4 vpTTPId (Virtual Path Trail Termination Point Identifier) . . . . . . . . . . . 468

DN70577885 15



List of tablesTable 1 aal2NodeId (AAL2 Node Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Table 2 AAL2EndAddress (AAL2 End Address) . . . . . . . . . . . . . . . . . . . . . . . . 54Table 3 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Table 4 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Table 5 aal2sigTTPId (AAL2 Signalling Link Identifier) . . . . . . . . . . . . . . . . . . . 56Table 6 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 57Table 7 stcAlarmEnable (Signalling Transport Converter Alarm Enable) . . . . . 58Table 8 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Table 9 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Table 10 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Table 11 aal2pathTTPId (AAL2 User Path Identifier) . . . . . . . . . . . . . . . . . . . . . 62Table 12 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 64Table 13 pid (Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Table 14 queue2Weight (Weight of AAL2 user path queue Q2) . . . . . . . . . . . . . 65Table 15 queue3Weight (Weight of AAL2 user path queue Q3) . . . . . . . . . . . . . 66Table 16 queue4Weight (Weight of AAL2 user path queue Q4) . . . . . . . . . . . . . 67Table 17 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Table 18 atmAccessProfileId (ATM Access Profile Identifier) . . . . . . . . . . . . . . . 69Table 19 egressBandwidth (Egress Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . 69Table 20 ingressBandwidth (Ingress Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . 71Table 21 amgrId (Account Manager Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 73Table 22 ldapConnectionType (LDAP Server TLS access mode) . . . . . . . . . . . . 73Table 23 primaryLdapPort (Port Number of Primary LDAP Server) . . . . . . . . . . 74Table 24 primaryLdapServer (IP address of Primary LDAP Server) . . . . . . . . . . 75Table 25 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Table 26 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Table 27 interfaceNumber (Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 78Table 28 nbapTTPId (Upper Layer Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . 79Table 29 nbapType (Upper Layer Connection Type) . . . . . . . . . . . . . . . . . . . . . . 80Table 30 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82Table 31 bfdActivation (BFD session activation flag) . . . . . . . . . . . . . . . . . . . . . . 83Table 32 bfdAdminUp (BFD session admin down state control) . . . . . . . . . . . . . 84Table 33 bfdDestAddress (Destination IP address for the BFD session) . . . . . . 85Table 34 bfdDetectMult (BFD session packets lost detection time multiplier) . . . 86Table 35 bfdGrp (BFD group reference) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87Table 36 bfdId (BFD session identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88Table 37 bfdSourceIpAddr (Source IP address for the BFD session) . . . . . . . . . 89Table 38 bfdSourceUdpPort (UDP source port of the BFD session) . . . . . . . . . . 90Table 39 bfdType (BFD session type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91Table 40 desMinTxInt (Desired minimum BFD control word transmit interval) . . 92Table 41 function (BFD session function definition) . . . . . . . . . . . . . . . . . . . . . . . 93Table 42 reqMinRxInt (Required minimum BFD control word receive interval) . . 94Table 43 bfdGrpId (BFD Group Identifier ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96Table 44 atmFabricId (ATM Fabric Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . 97Table 45 ubrPlusEnabled (UBR+ Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

16 DN70577885



Table 46 vccBundleEnabled (VCC Bundle Enabling Flag) . . . . . . . . . . . . . . . . . . 99Table 47 btsCertificateUpdateTime (BTS certificate update time) . . . . . . . . . . . 100Table 48 caCertificateUpdateTime (CA certificate update time) . . . . . . . . . . . . . 100Table 49 caSubjectName (CMP server subject name) . . . . . . . . . . . . . . . . . . . . 101Table 50 certhId (Certification Handler Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 102Table 51 cmpServerIpAddress (CMP Server IP Address) . . . . . . . . . . . . . . . . . 103Table 52 cmpServerPort (CMP Server Port) . . . . . . . . . . . . . . . . . . . . . . . . . . . 104Table 53 crServerIpAddress (CR Server IP Address) . . . . . . . . . . . . . . . . . . . . 105Table 54 crServerPort (CR Server Port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105Table 55 crlUpdatePeriod (Certificate Revocation List update period) . . . . . . . . 106Table 56 cesMinUDPPort (CES over PSN source port value range) . . . . . . . . . 108Table 57 cesifId (CES over PSN interface identifier) . . . . . . . . . . . . . . . . . . . . . 109Table 58 administrativeState (Administrative state) . . . . . . . . . . . . . . . . . . . . . . 110Table 59 cesPWid (CES over PSN Pseudowire Identifier) . . . . . . . . . . . . . . . . . 111Table 60 dscp (DSCP value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112Table 61 framesNumber (Number of frames per CESoPSN packet) . . . . . . . . . 113Table 62 jitterBufferSize (Jitter Buffer Size) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114Table 63 payloadTimeslots (Payload timeslots of TDM frame) . . . . . . . . . . . . . 115Table 64 remoteUDPPort (Remote UDP port number for CES over PSN) . . . . . 117Table 65 cesPWTid (CES over PSN pseudowire tunnel identifier) . . . . . . . . . . . 119Table 66 destIpAddress (Destination IP address) . . . . . . . . . . . . . . . . . . . . . . . 119Table 67 acceptableFrameTypes (Switch Port Acceptable Frame Types) . . . . . 121Table 68 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . . 122Table 69 ethLinkId (Ethernet Link Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123Table 70 flushFdbOnLos (Flush fdb on LOS mode) . . . . . . . . . . . . . . . . . . . . . . 125Table 71 l2BurstSize (Switch Port egress Shaper Burst Size) . . . . . . . . . . . . . . 126Table 72 l2IngressRate (Switch Port ingress RateLimiter Rate ) . . . . . . . . . . . . 127Table 73 l2ShaperRate (Switch Port egress Shaper Rate) . . . . . . . . . . . . . . . . 130Table 74 l2VlanIdList (Switch Port VLAN Member List) . . . . . . . . . . . . . . . . . . . 133Table 75 highValue (Switch Port VLAN Member Range High Value) . . . . . . . . . 134Table 76 lowValue (Switch Port VLAN Member Range Low Value) . . . . . . . . . . 135Table 77 linkOAMEnabled (Link OAM enabling flag) . . . . . . . . . . . . . . . . . . . . . 136Table 78 linkOAMProfile (Link OAM profile reference) . . . . . . . . . . . . . . . . . . . . 137Table 79 macAddr (MAC address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138Table 80 portDefaultPriority (Switch Port Default VLAN Priority) . . . . . . . . . . . . 138Table 81 portDefaultVlanId (Switch Port Default VLAN Identifier) . . . . . . . . . . . 139Table 82 speedAndDuplex (Speed and Duplex flag) . . . . . . . . . . . . . . . . . . . . . 140Table 83 synchEMode (Synchronous ethernet mode) . . . . . . . . . . . . . . . . . . . . 142Table 84 afrLinkInterfaceId (Fractional Interface Identifier) . . . . . . . . . . . . . . . . 143Table 85 afrTimeSlotSequence (ATM over Fractional JT1 Time Slot Sequence) . .

144Table 86 interfaceNumber (Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 146Table 87 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147Table 88 adaptationVersionMajor (Adaptation Version Major) . . . . . . . . . . . . . . 148Table 89 ftmId (BTS Transport Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148Table 90 locationName (Location Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149Table 91 softwareReleaseVersion (Software Release Version) . . . . . . . . . . . . . 150

DN70577885 17



Table 92 systemTitle (System Title) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151Table 93 userLabel (User Label) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152Table 94 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153Table 95 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153Table 96 atmIfNetId (ATM IP Net Interface Identifier) . . . . . . . . . . . . . . . . . . . . 154Table 97 destIpAddr (Destination IP Address) . . . . . . . . . . . . . . . . . . . . . . . . . . 156Table 98 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . 157Table 99 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158Table 100 cir (Committed information rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159Table 101 confCost (OSPF configured interface cost) . . . . . . . . . . . . . . . . . . . . 160Table 102 helloInterval (OSPF keepalive message transmission interval) . . . . . 161Table 103 ieifId (Identifier of the plain Ethernet interface) . . . . . . . . . . . . . . . . . . 162Table 104 interfaceArea (OSPF interface area) . . . . . . . . . . . . . . . . . . . . . . . . . 163Table 105 ipAddr (IP Address Info in the Transport Network) . . . . . . . . . . . . . . . 164Table 106 localIpAddr (Local Address of the IP Interface) . . . . . . . . . . . . . . . . . 165Table 107 netmask (IP Network Mask) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166Table 108 mtu (Maximum transfer unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166Table 109 mtuMismatchDetection (MTU mismatch detection in use) . . . . . . . . . 167Table 110 ospfWithBfd (OSPF uses additionally BFD) . . . . . . . . . . . . . . . . . . . . 168Table 111 proxyArpIpAddrList (List of proxy ARP IP addresses for this interface.) . .

169Table 112 qosEnabled (QOS traffic priorisation enabling flag) . . . . . . . . . . . . . . 170Table 113 retransInterval (OSPF LSA retransmission interval) . . . . . . . . . . . . . . 171Table 114 routerDeadInterval (OSPF router read interval) . . . . . . . . . . . . . . . . . 172Table 115 sbs (Shaper burst size) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173Table 116 sbsTotal (Total shaper burst size) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174Table 117 shapedBandwidth (Shaped Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . 175Table 118 sir (Shaper information rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176Table 119 sirTotal (Total shaper information rate) . . . . . . . . . . . . . . . . . . . . . . . . 177Table 120 trafficPathShapingEnable (Traffic path shaping enabling flag) . . . . . . 178Table 121 transmitDelay (OSPF packet transmission delay) . . . . . . . . . . . . . . . 180Table 122 upperLayerShaping (Upper Layer Shaping Enabled Flag) . . . . . . . . . 180Table 123 vlanEnabled (Vlan Enabled flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181Table 124 vlanId (Vlan ID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182Table 125 client_identifier (Entry set for DHCP clients identified by a system name)

184Table 126 dhcpClientIdentifier (DHCP Client Identifier) . . . . . . . . . . . . . . . . . . . . 184Table 127 dhcpFixedIpAddress (DHCP Fixed IP Address) . . . . . . . . . . . . . . . . . 185Table 128 dhcpAccessId (DHCP Server Identifier) . . . . . . . . . . . . . . . . . . . . . . . 186Table 129 hardware_identifier (Entry set of DHCP clients identified by a MAC

address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187Table 130 dhcpFixedIpAddress (DHCP Fixed IP Address) . . . . . . . . . . . . . . . . . 188Table 131 dhcpHardwareIdentifier (DHCP Hardware Identifier) . . . . . . . . . . . . . 189Table 132 range_identifier (DHCP server IP address pool) . . . . . . . . . . . . . . . . . 190Table 133 dhcpRangeEnd (DHCP Range End IP Address) . . . . . . . . . . . . . . . . 190Table 134 dhcpRangeStart (DHCP Range Start IP Address) . . . . . . . . . . . . . . . 191Table 135 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . 193Table 136 imaGroupId (IMA group identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194

18 DN70577885



Table 137 imaVersionId (IMA Version Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 195Table 138 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 196Table 139 interfaces (Physical interface list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196Table 140 minNumLinks (Minimum Number of Links) . . . . . . . . . . . . . . . . . . . . . 197Table 141 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198Table 142 ntpAccessId (NTP Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200Table 143 ntpServers (List of NTP Server IP Addresses) . . . . . . . . . . . . . . . . . . 200Table 144 bfdHoldUpTime (BFD throttle time for re-installing protection routes) . 202Table 145 btsId (BTS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203Table 146 btsIpAddr (Base Station IP Address) . . . . . . . . . . . . . . . . . . . . . . . . . . 203Table 147 cPlaneIpAddress (Control-plane application IP address) . . . . . . . . . . 204Table 148 cesopsnIpAddress (CES over PSN application IP address) . . . . . . . . 206Table 149 disableFtp (Disable FTP server) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207Table 150 flexBusIpAddr (Public IP Address of Flexbus Part of BTS) . . . . . . . . . 208Table 151 fpLocalUdpPort (Local UDP port for small packets multiplexing) . . . . 208Table 152 fpMuxAmount (Maximum amount of small packets that can be

multiplexed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209Table 153 fpMuxDelay (Small packets multiplexing delay time) . . . . . . . . . . . . . . 210Table 154 fpRemoteUdpPort (Remote UDP port for small packets multiplexing) 211Table 155 ftmIpAddr (Flexi Transport Module IP Address) . . . . . . . . . . . . . . . . . . 212Table 156 ftmNetmask (Netmask of the public IP address) . . . . . . . . . . . . . . . . . 213Table 157 iHSPAAdapterCommissioningParameter (I-HSPA adapter initial commis-

sioning parameters) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214Table 158 iHSPAmode (I-HSPA mode activation flag) . . . . . . . . . . . . . . . . . . . . . 215Table 159 icmpResponseEnabled (Enable response to ICMP traffic) . . . . . . . . . 215Table 160 ipNodeId (IP Node Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216Table 161 linkOAMLoopbackSupport (Link OAM remote loopback discovery enabling

flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217Table 162 mPlaneIpAddress (Management -plane application IP address) . . . . . 218Table 163 mtu (Maximum transfer unit of the BTS) . . . . . . . . . . . . . . . . . . . . . . . 219Table 164 oamCir (Committed information rate for Service OAM messages) . . . 220Table 165 oamTlvReply (Optional TLV message reply flag) . . . . . . . . . . . . . . . . 221Table 166 omsTls (TLS usage towards the O&M system) . . . . . . . . . . . . . . . . . . 222Table 167 ret1IpAddr (RET IP Address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223Table 168 rncIpAddr (RNC IP Address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224Table 169 sPlaneIpAddress (Synchronization-plane application IP address) . . . 225Table 170 transportMode (BTS transport mode) . . . . . . . . . . . . . . . . . . . . . . . . . 226Table 171 twampMessageRate (TWAMP initiator rate for sending messages) . . 227Table 172 twampReflectorOn (TWAMP message response enabling flag) . . . . . 228Table 173 twampReflectorPort (TWAMP reflector port number) . . . . . . . . . . . . . 229Table 174 twampSourcePort (TWAMP source port number) . . . . . . . . . . . . . . . . 230Table 175 uPlane2IpAddress (Second user-plane application IP address) . . . . . 231Table 176 uPlane2IpInterface (Second user-plane application IP network interface)

232Table 177 uPlaneIpAddress (User plane application IP address) . . . . . . . . . . . . 233Table 178 uPlaneIpInterface (User-plane application IP network interface) . . . . . 235Table 179 RmExceptions (Restricted Mode Exception) . . . . . . . . . . . . . . . . . . . . 237Table 180 sourceTwoDiscr (How is source two defined?) . . . . . . . . . . . . . . . . . . 238

DN70577885 19



Table 181 sourceTwoIpAddr (IP address for source two) . . . . . . . . . . . . . . . . . . 239Table 182 sourceTwoNetMask (IP Subnet Mask) . . . . . . . . . . . . . . . . . . . . . . . . 240Table 183 userLabel (User Label) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241Table 184 iprmId (IP Restricted Mode Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 242Table 185 ipRoutingTableId (IP Routing Table Identifier) . . . . . . . . . . . . . . . . . . 243Table 186 staticRoutes (List of static routes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244Table 187 bfdId (BFD route protection session identifier) . . . . . . . . . . . . . . . . . . 244Table 188 destIpAddr (Route destination IP address) . . . . . . . . . . . . . . . . . . . . . 245Table 189 gateway (IP address of the next hop of the route) . . . . . . . . . . . . . . . 246Table 190 netmask (Netmask of the destination IP address) . . . . . . . . . . . . . . . 247Table 191 preference (Preference value for the route) . . . . . . . . . . . . . . . . . . . . 248Table 192 cESoPSN (CES over PSN flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250Table 193 cir (Committed information rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251Table 194 confCost (OSPF configured interface cost) . . . . . . . . . . . . . . . . . . . . 252Table 195 helloInterval (OSPF keepalive message transmission interval) . . . . . 252Table 196 interfaceArea (OSPF interface area) . . . . . . . . . . . . . . . . . . . . . . . . . 253Table 197 localIpAddr (Local Address of the IP Interface) . . . . . . . . . . . . . . . . . 254Table 198 mtuMismatchDetection (MTU mismatch detection in use) . . . . . . . . . 255Table 199 netmask (IP network mask of the local IP address) . . . . . . . . . . . . . . 256Table 200 ospfWithBfd (OSPF uses additionally BFD) . . . . . . . . . . . . . . . . . . . . 257Table 201 proxyArpIpAddrList (List of proxy ARP IP addresses for this interface.) . .

257Table 202 qosEnabled (QOS traffic priorisation enabling flag) . . . . . . . . . . . . . . 258Table 203 retransInterval (OSPF LSA retransmission interval) . . . . . . . . . . . . . . 259Table 204 routerDeadInterval (OSPF router read interval) . . . . . . . . . . . . . . . . . 260Table 205 sbs (Shaper burst size) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261Table 206 sir (Shaper information rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262Table 207 transmitDelay (OSPF packet transmission delay) . . . . . . . . . . . . . . . 263Table 208 vlanId (VLAN identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264Table 209 vlanIfNetId (VLAN interface object identifier) . . . . . . . . . . . . . . . . . . . 265Table 210 dscpMap (DSCP to priority queue map) . . . . . . . . . . . . . . . . . . . . . . . 266Table 211 dscp (DSCP value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267Table 212 priorityQueue (Priority queue identifier) . . . . . . . . . . . . . . . . . . . . . . . 268Table 213 enableLayer2Switching (Ethernet Switch Enable) . . . . . . . . . . . . . . . 269Table 214 l2PriorityQueueWeight2 (Layer 2 switch member weight for priority queue

2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270Table 215 l2PriorityQueueWeight3 (Layer 2 switch member weight for priority queue




6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273Table 219 portDefaultPriority (Switch Port Default VLAN Priority (internal Port)) 274Table 220 portDefaultVlanId (Switch Port Default VLAN Identifier (internal Port)) 275Table 221 priorityQueueNonIP (Priority queue for non-IP frames) . . . . . . . . . . . 276Table 222 priorityQueuePcp0 (Priority queue for ethernet frames with VLAN PCP bits

20 DN70577885



0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277Table 223 priorityQueuePcp1 (Priority queue for ethernet frames with VLAN PCP bits







7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285Table 230 priorityQueueUntagged (Priority queue for untagged ethernet frames) 286Table 231 qosClassification (QoS Classification Mode) . . . . . . . . . . . . . . . . . . . . 287Table 232 switchId (Layer 2 Switch Object Identifier) . . . . . . . . . . . . . . . . . . . . . . 287Table 233 vlanAwareSwitch (VLAN Aware Switching Enable) . . . . . . . . . . . . . . . 288Table 234 assocId (Maintenance association identifier) . . . . . . . . . . . . . . . . . . . . 290Table 235 maName (Name of the maintenance domain) . . . . . . . . . . . . . . . . . . . 290Table 236 vlanId (VLAN identifier of the maintenance association) . . . . . . . . . . . 291Table 237 domainId (Maintenance domain identifier) . . . . . . . . . . . . . . . . . . . . . . 293Table 238 mdLevel (Level of the maintenance domain) . . . . . . . . . . . . . . . . . . . . 293Table 239 mdName (Name of the maintenance domain) . . . . . . . . . . . . . . . . . . . 294Table 240 aisEnabled (AIS message transmission enabling flag) . . . . . . . . . . . . 296Table 241 aisTxPeriod (AIS messages transmission period) . . . . . . . . . . . . . . . . 296Table 242 ccmTxPeriod (Continuity Check Messages transmission period) . . . . 297Table 243 enableCcm (Allow sending of CCM messages and reset CCM counters) .

298Table 244 ethernetPort (Ethernet link reference) . . . . . . . . . . . . . . . . . . . . . . . . . 299Table 245 oammepId (Maintenance association endpoint identifier) . . . . . . . . . . 300Table 246 remoteMepList (Remote maintenance association endpoints list) . . . . 301Table 247 macAddr (MAC address of the remote MEP) . . . . . . . . . . . . . . . . . . . 302Table 248 mepId (Remote maintenance association endpoint identifier) . . . . . . . 303Table 249 vlanPrio (VLAN PCP bits) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304Table 250 activeMode (Link OAM operational mode at local peer) . . . . . . . . . . . 305Table 251 alarmClearanceDelay (Link OAM Link Critical Event Alarm clearance

delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306Table 252 efEventThreshold (Errored Frame Event counting threshold) . . . . . . . 306Table 253 efEventWindow (Errored Frame Event counting interval) . . . . . . . . . . 307Table 254 efpEventThreshold (Errored Frame Period Event counting threshold) 308Table 255 efpEventWindow (Errored Frame Period Event counting interval) . . . 309Table 256 efssEventThreshold (Errored Frame Seconds Summary Event counting

threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310Table 257 efssEventWindow (Errored Frame Seconds Summary Event counting

interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311Table 258 enableCcm (Allow sending of CCM messages and reset CCM counters) .

312

DN70577885 21



Table 259 eventRepetition (OAM PDU message transmission rate) . . . . . . . . . . 313Table 260 eventSupport (Link OAM event support flag) . . . . . . . . . . . . . . . . . . . 314Table 261 linkLostTime (Link OAM link lost time) . . . . . . . . . . . . . . . . . . . . . . . . 315Table 262 loopBackTime (Link OAM loopback duration) . . . . . . . . . . . . . . . . . . . 316Table 263 profileId (Profile instance identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . 317Table 264 testFrameRate (Link OAM loopback test message rate) . . . . . . . . . . 318Table 265 testFrameSize (Link OAM loopback test message frame size) . . . . . 318Table 266 confPref (OSPF routing preference value) . . . . . . . . . . . . . . . . . . . . . 320Table 267 ospfAreas (OSPF area list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320Table 268 areaId (OSPF area identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321Table 269 areaStub (OSPF area stub flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322Table 270 ospfEnabled (OSPF enabling flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . 323Table 271 ospfRouterId (OSPF router identification) . . . . . . . . . . . . . . . . . . . . . . 324Table 272 ospfV2Id (OSPF configuration identifier) . . . . . . . . . . . . . . . . . . . . . . 325Table 273 refBandwidth (Reference bandwidth for OSPF cost equal to 1) . . . . . 326Table 274 spfDelay (OSPF Shortest Path First recalculation delay) . . . . . . . . . . 327Table 275 spfHoldTime (OSPF Shortest Path First hold time) . . . . . . . . . . . . . . 327Table 276 spfMaxHoldTime (OSPF maximum Shortest Path First hold time) . . . 328Table 277 acFieldCompressionOn (Access Control Field Compression flag) . . . 330Table 278 fcsFieldLength (Frame Check Sequence field size) . . . . . . . . . . . . . 331Table 279 magicNumberOn (Magic number flag) . . . . . . . . . . . . . . . . . . . . . . . . 331Table 280 mruSize (Maximum Receive Unit (MRU) size) . . . . . . . . . . . . . . . . . . 332Table 281 p3lpId (PPP link identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334Table 282 protocolFieldCompressionOn (Protocol Field Compression flag) . . . . 335Table 283 administrativeState (Administrative state of the PPP multi-link) . . . . . 337Table 284 endPointDiscriminatorType (Endpoint discriminator type) . . . . . . . . . 338Table 285 interfaces (Physical interface list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338Table 286 mpFragmentSize (Fragment size in egress direction) . . . . . . . . . . . . 339Table 287 mrruSize (Maximum Receive Reconstructed Unit (MRRU) size) . . . . 340Table 288 netmask (Netmask of the IP address of the PPP endpoint) . . . . . . . . 342Table 289 p3mlId (PPP multi-link identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343Table 290 p3pIpAddr (PPP endpoint IP address) . . . . . . . . . . . . . . . . . . . . . . . . 343Table 291 shortSeqNrOn (Short sequence numbering flag) . . . . . . . . . . . . . . . . 344Table 292 ts16Excluded (Is timeslot TS16 excluded) . . . . . . . . . . . . . . . . . . . . . 345Table 293 administrativeState (Administrative state of the PPP link) . . . . . . . . . 347Table 294 interface (Physical interface list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347Table 295 netmask (Netmask for the IP address of the PPP endpoint) . . . . . . . 348Table 296 p3pIpAddr (PPP endpoint IP address) . . . . . . . . . . . . . . . . . . . . . . . . 349Table 297 p3slId (PPP single link object instance identifier) . . . . . . . . . . . . . . . . 350Table 298 ts16Excluded (Is timeslot TS16 excluded) . . . . . . . . . . . . . . . . . . . . . 351Table 299 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . 353Table 300 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . 353Table 301 pdhLbo (PDH Line Build Out) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354Table 302 pdhLineType (PDH Line Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355Table 303 pdhPSTTPId (PDH Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 357Table 304 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359Table 305 bfdAdminUp (BFD actual session administration flag) . . . . . . . . . . . . 360

22 DN70577885



Table 306 bfdEnable (Bidirectional Forwarding Enabled) . . . . . . . . . . . . . . . . . . . 360Table 307 cellsConcatUl (Uplink Concatenation Factor.) . . . . . . . . . . . . . . . . . . . 361Table 308 ctpList (Set of registered vcCTPs.) . . . . . . . . . . . . . . . . . . . . . . . . . . . 362Table 309 labelDl (Downlink MPLS Header) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363Table 310 labelUl (Uplink MPLS Header) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364Table 311 perHopBehaviour (Per hop behaviour DiffServ) . . . . . . . . . . . . . . . . . 364Table 312 pkTimer (Packetization Timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366Table 313 pwMplsId (MPLS Pseudowire Identifier) . . . . . . . . . . . . . . . . . . . . . . . 367Table 314 bfdTimer (BFD Timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368Table 315 bfdDetectMult (Maximum allowed number of lost control packets for BFD)

368Table 316 desiredMinTxIntvl (Desired Minimum Transmit Interval) . . . . . . . . . . . 369Table 317 requiredMinRxIntvl (Required Minimum Receive Interval) . . . . . . . . . . 370Table 318 cwEnable (Control Word Enable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371Table 319 pwNeId (Pseudowire Network Element Identifier) . . . . . . . . . . . . . . . . 372Table 320 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . . 373Table 321 attachedPWList (Attached Pseudo-Wires List) . . . . . . . . . . . . . . . . . . 373Table 322 pwTipId (Pseudowire Tunnel IP Identifier) . . . . . . . . . . . . . . . . . . . . . . 374Table 323 remoteIpv4Addr (Remote IPv4 Address) . . . . . . . . . . . . . . . . . . . . . . . 375Table 324 perHopBehaviourWeightList (Per Hop Behaviour Weight List) . . . . . . 377Table 325 assuredForwardingClass1 (Assured Forwarding Class 1 Weight Value) .

378Table 326 assuredForwardingClass2 (Assured Forwarding Class 2 Weight Value) .



380Table 329 bestEffort (Best Effort Weight Value) . . . . . . . . . . . . . . . . . . . . . . . . . . 381Table 330 qosId (Quality of Service Configuration Identifier) . . . . . . . . . . . . . . . . 382Table 331 trafficTypesMap (Quality of Service mapping table) . . . . . . . . . . . . . . 382Table 332 dscpList (Differentiated Services Code Point list) . . . . . . . . . . . . . . . . 383Table 333 pHB (Per Hop Behaviour) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384Table 334 trafficType (Traffic type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385Table 335 vlanPrio (Vlan priority flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387Table 336 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . . 389Table 337 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 390Table 338 laserMode (Laser Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390Table 339 rdiOnExcessiveBer (Remote Defect Indication On Excessive Bit Error

Ratio) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391Table 340 sdhifId (SDH Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392Table 341 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393Table 342 xmtTraceId_HP (Sent Trace Identifier (J1, HOP)) . . . . . . . . . . . . . . . . 394Table 343 xmtTraceId_RS (Sent Trace Identifier (J0, RS)) . . . . . . . . . . . . . . . . . 394Table 344 ssmSelExt2M (SSM Selection with external 2.048 MHz) . . . . . . . . . . 396Table 345 ssmSelPDH (SSM Selection with TDM) . . . . . . . . . . . . . . . . . . . . . . . 397Table 346 ssmSelSyncE (SSM Selection with SyncE) . . . . . . . . . . . . . . . . . . . . . 398Table 347 ssmTxUntagged (Send SSM message frames untagged) . . . . . . . . . . 399

DN70577885 23



Table 348 ssmType (SSM support network standard) . . . . . . . . . . . . . . . . . . . . . 399Table 349 synchERegenOn (Activate the synchronous ethernet regenerator

function) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400Table 350 synchroSourceList (The synchronization sources of the BTS) . . . . . . 401Table 351 clockProtocol (Protocol of the clock source) . . . . . . . . . . . . . . . . . . . . 402Table 352 interfaceNumber (Interface number) . . . . . . . . . . . . . . . . . . . . . . . . . . 403Table 353 priority (Clock source priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405Table 354 ssmAcceptanceLevel (SSM defined value) . . . . . . . . . . . . . . . . . . . . 405Table 355 ssmEnabled (SSM enabling flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406Table 356 ssmTimeout (SSM message timeout) . . . . . . . . . . . . . . . . . . . . . . . . . 407Table 357 unitNumber (Unit number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408Table 358 timingGenPgId (Synchronisation Protection Group Identifier) . . . . . . 409Table 359 syncId (Clock Synchronization Configuration Identifier) . . . . . . . . . . . 411Table 360 interfaceNumber (Interface number) . . . . . . . . . . . . . . . . . . . . . . . . . . 412Table 361 tcAdaptorTTPId (ATM Interface Identifier) . . . . . . . . . . . . . . . . . . . . . 413Table 362 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414Table 363 cacCommittedBitRate (CAC Committed Bit Rate) . . . . . . . . . . . . . . . 415Table 364 dcnCommittedBitRate (DCN Committed Bit Rate) . . . . . . . . . . . . . . . 417Table 365 externalNATIpAddress (External NAT IP Address) . . . . . . . . . . . . . . 418Table 366 farEndSctpSubnetIpAddress (Far End SCTP Subnet IP Address ) . . 419Table 367 farEndSctpSubnetMask (Far End SCTP Subnet Mask) . . . . . . . . . . . 420Table 368 minSCTPPort (Minimum SCTP port number) . . . . . . . . . . . . . . . . . . . 420Table 369 minUDPPort (Minimum UDP port number) . . . . . . . . . . . . . . . . . . . . . 421Table 370 signallingCommittedBitRate (Signalling Committed Bit Rate) . . . . . . . 422Table 371 tmparId (TMPAR Object Instance Identifier) . . . . . . . . . . . . . . . . . . . . 423Table 372 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . 425Table 373 logMeanSyncValue (Log mean synchronization value) . . . . . . . . . . . 425Table 374 masterIpAddr (IP Address of the ToP master) . . . . . . . . . . . . . . . . . . 426Table 375 topId (Timing Over Packet Configuration Identifier) . . . . . . . . . . . . . . 427Table 376 atmTrafficDescriptorId (Traffic Descriptor Identifier) . . . . . . . . . . . . . . 429Table 377 conformanceDefinition (Conformance Definition) . . . . . . . . . . . . . . . . 429Table 378 minDesiredCellRate (Minimum Desired Cell Rate) . . . . . . . . . . . . . . . 430Table 379 peakCellRate (Peak Cell Rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431Table 380 ubrShare (UBR Share) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 432Table 381 userLabel (User Label) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433Table 382 administrativeState (Lock or unlock a TWAMP session) . . . . . . . . . . 435Table 383 destIpAddress (TWAMP session destination IP address) . . . . . . . . . 436Table 384 destPort (TWAMP session destination port) . . . . . . . . . . . . . . . . . . . . 437Table 385 dscp (DSCP value for TWAMP message transmission) . . . . . . . . . . . 437Table 386 messageSize (TWAMP initiator message size) . . . . . . . . . . . . . . . . . 438Table 387 plrAlarmThreshold (Packet loss ratio alarm threshold) . . . . . . . . . . . . 439Table 388 rttAlarmThreshold (Round-trip-time alarm threshold) . . . . . . . . . . . . . 440Table 389 sourceIpAddress (TWAMP initiator messages source IP address) . . 441Table 390 twampId (TWAMP session identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 442Table 391 enableRP301Interface (Enable RP3-01 interface) . . . . . . . . . . . . . . . 444Table 392 unitId (Unit Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444Table 393 unitTypeActual (Installed hardware unit type) . . . . . . . . . . . . . . . . . . . 445

24 DN70577885



Table 394 unitTypeExpected (Expected hardware unit type) . . . . . . . . . . . . . . . . 447Table 395 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450Table 396 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450Table 397 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 451Table 398 trafficDescriptorId (Traffic Descriptor Pointer) . . . . . . . . . . . . . . . . . . . 452Table 399 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 453Table 400 vcCTPId (Virtual Channel Identifier (VCI)) . . . . . . . . . . . . . . . . . . . . . . 454Table 401 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455Table 402 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455Table 403 aalProfilePtr (ATM Adaptation Layer (AAL) Profile Pointer) . . . . . . . . 456Table 404 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 457Table 405 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458Table 406 vcTTPId (Virtual Channel Trail Termination Point Identifier) . . . . . . . . 459Table 407 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 461Table 408 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 461Table 409 trafficDescriptorId (Traffic Descriptor Pointer) . . . . . . . . . . . . . . . . . . . 462Table 410 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 463Table 411 vpCTPId (Virtual Path Identifier (VPI)) . . . . . . . . . . . . . . . . . . . . . . . . . 464Table 412 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 466Table 413 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 466Table 414 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 467Table 415 vpTTPId (Virtual Path Trail Termination Point Identifier) . . . . . . . . . . . 468

DN70577885 25

Flexi Transport Module Parameters Summary of changes

Id:0900d805808f18bbConfidential

Summary of changesChanges between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues.

Changes between issues 03E (2011-10-26, RU30) and 03F (2011-12-16, RU30)Changed parameters

ANBAnbapTTPId (Upper Layer Path Identifier)

TWAMPmessageSize (TWAMP initiator message size)

Removed parametersIVIF

– desMinTxInt (BFD desired minimum transmit interval)

Changes between issues 03D (2011-09-23, RU30) and 03E (2011-10-26, RU30)Changed parameters

BFDbfdGrp (BFD group reference)

Field 03E 03F

Description Identifies the upper layer path. The object is identified by - Unit number (unit#) - Interface number(if#, imag# or pw#) - Virtual Path Identifier (vpi#) - Virtual Channel Identifier (vci#) Format: - unit#-if#-vpi#vci# (e.g. 2-8-000C0) - unit#-imag#-vpi#vci# (e.g. 2-34-00210) Range: unit#: 1 if#: 1..16 (maxi. 2 digits) imag#: 33..75 (2 digits) pw#: 76 vpi#: 00..FF (hexadecimal number, 2 digits) vci#: 000..FFF (hexadecimal number, 3 digits)

Identifies the upper layer path. The object is identified by - Unit number (unit#) - Interface number(if#, imag# or pw#) - Virtual Path Identifier (vpi#) - Virtual Channel Identifier (vci#) Format: - unit#-if#-vpi#vci# (e.g. 1-8-000C0) - unit#-imag#-vpi#vci# (e.g. 1-34-00210) Range: unit#: 1 if#: 1..16 (maxi. 2 digits) imag#: 33..75 (2 digits) pw#: 76 vpi#: 00..FF (hexadecimal number, 2 digits) vci#: 000..FFF (hexadecimal number, 3 digits)

Field 03E 03F

Range and step 69..1500, step 1 69..1400, step 1

Default value 69 100

26 DN70577885



Summary of changes

CERTHbtsCertificateUpdateTime (BTS certificate update time)

caCertificateUpdateTime (CA certificate update time)

CESPWjitterBufferSize (Jitter Buffer Size)

framesNumber (Number of frames per CESoPSN packet)

ETHLKlinkOAMEnabled (Link OAM enabling flag)

Field 03D 03E

Description This parameter references the BFD group of which the BFD session is a member. The parameter is a managed object instance identifier (LMOID), referencing an instance of object class BFDGRP. The parameter may remain empty, meaning the BFD session is not bound to a BFD group.

This parameter references the BFD group id to which the BFD session belongs. The parameter is a managed object instance identifier (LMOID), referencing an instance of object class BFDGRP. The parameter may remain empty, meaning the BFD session is not bound to a BFD group.

Field 03D 03E


Default value notes Default value is 1 year. Default value is 1 month.

Field 03D 03E


Default value notes Default value is 5 years. Default value is 6 months.

Field 03D 03E


Field 03D 03E


DN70577885 27



FTMadaptationVersionMajor (Adaptation Version Major)

IPNOdisableFtp (Disable FTP server)

IPRTstaticRoutes (List of static routes)

OAMMEPethernetPort (Ethernet link reference)

Field 03D 03E

Description Enables the Link OAM functionality for this ethernet link. In consequence: - the values of all statistics counters of the Link OAM feature for this interface are set to 0 - the Link OAM alarms for this inter-face are cleared - the Link OAM discovery process is started, either in active or in passive mode.

Enables the Link OAM functionality for this ethernet link. In consequence: - the values of all statistics counters of the Link OAM feature for this interface are set to 0 - the Link OAM alarms for this inter-face are cleared - the Link OAM discovery process is started, either in active or in passive mode. linkOAMEnabled cannot be set to FB bit pipe interfaces

Field 03D 03E

Range and step 5..6 characters 1..9 characters

Default value WN7.0 WN7.0_2.0

Field 03D 03E

Description Control whether to allow/disallow running FTP server on Transport module for security reasons

Control whether to allow/disallow running FTP server on Transport module for security reasons. FSMr3 HW units are not supported.

Field 03D 03E

Description Contains a list of the static routes. Contains the list of static (configured) routes.

28 DN70577885



Summary of changes

STPGunitNumber (Unit number)

Changes between issues 03C (2011-06-22, RU30) and 03D (2011-09-23, RU30)

New ParametersETHLKflushFdbOnLos (Flush fdb on LOS mode)

P3MLshortSeqNrOn (Short sequence numbering flag)

UNITenableRP301Interface (Enable RP3-01 interface)

Field 03D 03E

Description This parameter specifies the ethernet link that the FTM shall use for sending Service OAM messages. The parameter is a local managed object instance identi-fier (LMOID), i.e. a reference to an instance of object class ETHLK.

This parameter specifies the ethernet link that the FTM shall use for sending Service OAM messages. The parameter is a local managed object instance identi-fier (LMOID), i.e. a reference to an instance of object class ETHLK. ethernet-port cannot be set to FB bit pipe interface.

Field 03D 03E

Description This parameter specifies the location of the unit providing the synchronisation source interface.

This parameter specifies the location of the unit providing the synchronisation source interface. unitNumber shall be "0" for ToP sync source when unit is FSM/FSI/FTIF/FIIF.

Description This parameter is true then dynamic MAC address entries of Forwarding Database (fdb) should be flushed when an Ethernet Layer Loss of Signal (LOS) is detected on one of its external switch-ports.

Description This parameter specificies how packets are numbered. The Long Sequence Number Format uses 24 bits for the fragment sequence number, the short sequence format 12 bits (RFC 1990). If shortSeqNrOn equals true, the short sequence number is used.

DN70577885 29



Changed parameters

A2STaal2sigTTPId (AAL2 Signalling Link Identifier)

interfaceNumber (Interface Number)

Description Configure and designate EIF2(Out-door)/EIF5(Indoor) on the Flexi System Module (FCT) as RP3-01 interface

Field 03C 03D

Description This parameter identifies the AAL2 sig-nalling link. The identifier is composed from the elements: - Unit number (unit#) - Interface number(if#, imag# or pw#) - Virtual Path Identifier (vpi#) - Virtual Channel Identifier (vci#) Format: - unit#-if#-vpi#vci# (e.g. 1-8-000C0) - unit#-imag#-vpi#vci# (e.g. 1-34-00210) Range: unit#: 1 if#: 1..16 (maxi. 2 digits) imag#: 33..75 (2 digits) pw#: 76 vpi#: 00..FF (hexadecimal number, 2 digits) vci#: 000..FFF (hexadecimal number, 3 digits)

This parameter identifies the AAL2 sig-nalling link. The identifier is composed from the elements: - Unit number (unit#) - Interface number(if#, imag# or pw#) - Virtual Path Identifier (vpi#) - Virtual Channel Identifier (vci#) Format: - unit#-if#-vpi#vci# (e.g. 1-8-000C0) - unit#-imag#-vpi#vci# (e.g. 1-34-00210) Range: unit#: 1 if#: 1..16 (maxi. 2 digits) imag#: 33..75 (2 digits) pw#: 76 vpi#: 00..FF (hexadecimal number, 2 digits) vci#: 000..FFF (hexadecimal number, 3 digits)

Field 03C 03D

Description Defines the location of the physical inter-face on the unit. The value range depends on the unit type. FTEB, FTPB: 1..8 FIIB, FILB, FTIA, FTIB, FTJA, FTLB: 1..4 FTFB, FTFA, FTHA: 1..16 In case of Inverse Multiplexing for ATM (IMA) the value range is: 33..75. For ATM over Ethernet, the value is always: 76.

Defines the location of the physical inter-face on the unit. The value range depends on the unit type. FTEB, FTPB, FTIF, FIIF: 1..8 FIIB, FILB, FTIA, FTIB, FTJA, FTLB: 1..4 FTFB, FTFA, FTHA: 1..16 In case of Inverse Multiplexing for ATM (IMA) the value range is: 33..75. For ATM over Ethernet, the value is always: 76.

30 DN70577885



Summary of changes

A2UTinterfaceNumber (Interface Number)

AMGRamgrId (Account Manager Identifier)

ANBAinterfaceNumber (Interface Identifier)

Field 03C 03D



Field 03C 03D

Description This parameter identifies the account manager. The value is always 1. Exactly 1 account manager object exists on the BTS.

This parameter identifies the BTS account manager configuration. The value is always 1.

Field 03C 03D

Description Defines the location on the unit of the physical interface that carries the signal-link link. The value depends on the unit type. FTEB: 1..8 FTPB: 1..8 FTIA: 1..4 FTIB: 1..4 FTFA: 1..16 FTHA: 1..16 FTJA: 1..4 FTLB: 1..4 For IMA, the parameter identifies the IMA group. Values are: 33..75. For the ATM over Ethernet pseudowire the value is always: 76.

Defines the location on the unit of the physical interface that carries the signal-link link. The value depends on the unit type. FTEB, FTPB, FTIF, FIIF: 1..8 FTIA, FTIB, FTJA, FTLB: 1..4 FTFA, FTHA: 1..16 For IMA, the parameter identifies the IMA group. Values are: 33..75. For the ATM over Ethernet pseudowire the value is always: 76.

DN70577885 31



CERTHcerthId (Certification Handler Identifier)

CESPWcesPWid (CES over PSN Pseudowire Identifier)

ETHLKethLinkId (Ethernet Link Identifier)

Field 03C 03D

Description This parameter identifies the unique instance of the certification handler object class of the BTS. Value is always 1.

This parameter identifies the certificate handler configuration. The value is always 1.

Field 03C 03D

Description This parameter identifies the CES over PSN pseudowire. The format of the parameter is slot#-if# where slot# is the slot of the unit where the interface resides and if# is the interface number of the corresponding PDH interface on this unit. In this release slot is always 1. The value range of the if# part of the parameter depends on the hardware: FIIB, FILB, FTIB, FTLB: 1:4 FTFB: 1-16

This parameter identifies the CES over PSN pseudowire. The format of the parameter is slot#-if# where slot# is the slot of the unit where the interface resides and if# is the interface number of the corresponding PDH interface on this unit. In this release slot is always 1. The value range of the if# part of the parameter depends on the hardware: FIIB, FILB, FTIB, FTLB: 1..4 FTIF, FIIF: 1..8 FTFB: 1..16

32 DN70577885



Summary of changes

DN70577885 33



Field 03C 03D

Description This parameter identifies the Ethernet link. It is formed as "ETHLK-s#-p#" where s# is the slot number - in this release always 1 - and p# is the port number [1..4]. Example "1-1". The value range of port number p# is [1..4] for the FTFB hardware unit and [1..3] for all other hardware unit types. For FTFB the port numbers 1 and 2 are reserved for the external Gigabit ethernet links and port numbers 3 and 4 are reserved for the ethernet links towards the FlexBus.

This parameter identifies the BTS trans-port Ethernet interface. Format: "slot#-if#" where slot# = slot number of the unit con-taining the Ethernet interfaces, and if# = the interface number of the physical interface on the unit and for FTIB/FTLB, slot#: 1 : This is always 1, since there is only 1 slot. if#: 1..3 for FTFB, slot#: 1 : This is always 1, since there is only 1 slot. if#: 1..4 Ports 1 and 2 are reserved for the external Gigabit Ethernet links. Ports 3 and 4 are reserved for the Ethernet links towards the FlexBus. for Flexi BTS Release 3 Outdoor System Module (FSM), slot#: 0 : This is always 0, since Transport is integrated into common system module. if#: 1..2 : Value range is 1..2 for EIF1..EIF2 on this unit Additionally, EIF2 can be configured as an RP3-01 port. for Flexi BTS Release 3 Indoor System Module (FSI), slot#: 0 : This is always 0, since Transport is integrated into common system module. if#: 1..5 : Value range is 1..5 for EIF1..EIF5. Usage of EIF1 and EIF3 is mutually exclusive. Similarly for EIF2 and EIF4. Additionally, EIF5 can be configured as an RP3-01 port. for FTIF (optional outdoor external Transport module), slot#: 1 : The slot number is '1', since this is an additional unit if#: 1..4 : Value range is 1..4 for EIF1..EIF4 on this unitFTIF/FIIF:

34 DN70577885



Summary of changes

FTMadaptationVersionMajor (Adaptation Version Major)

IAIFinterfaceNumber (Interface Number)

Description (cont.) Usage of EIF1 and EIF3 is mutually exclusive. Similarly for EIF2 and EIF4. Usage of EIF1/EIF3 on this unit and EIF2 on FSM is mutually exclusive. for FIIF (optional indoor external Transport module), slot#: 1 : The slot number is '1', since this is an additional unitif#: 1..2 : Value range is 1..2 for EIF1..EIF2 on this unit Usage of EIF1 and EIF2 is mutually exclusive on this unit. Usage of EIF1/EIF2 on this unit and EIF5 on FSI unit is mutually exclusive. Examples: FTIB/FTLB:1-1: refers to the physical Ethernet inter-face 1 in slot 1. (EIF1) FTFB: 1-1: refers to the physical Gigabit Ethernet interface 1 in slot 1. (EIF1) FSI/FSM: 0-1: refers to the physical Ethernet interface 1 in slot 0. (EIF1)1-1: refers to the physical Ethernet inter-face 1 in slot 1. (EIF1)

Field 03C 03D

Field 03C 03D

Default value WN6.0 WN7.0

DN70577885 35



IEIFieifId (Identifier of the plain Ethernet interface)

IMAGinterfaces (Physical interface list)

Field 03C 03D

Description Defines the location on the unit of the physical interface that carries the signal-link link. The value depends on the unit type. FTEB: 1..8 FTPB: 1..8 FTIA: 1..4 FIIB, FTIB: 1..4 FTFA: 1..16 FTHA: 1..16 FTJA: 1..4 FILB, FTLB: 1..4 For IMA, the parameter identifies the IMA group. Values are: 33..75. For the ATM over Ethernet pseudowire the value is always: 76.

Defines the location on the unit of the physical interface that carries the signal-link link. The value depends on the unit type. FTEB, FTPB, FTIF, FIIF: 1..8 FTIA, FIIB, FTIB, FTJA, FILB, FTLB: 1..4 FTFA, FTHA: 1..16 For IMA, the parameter identifies the IMA group. Values are: 33..75. For the ATM over Ethernet pseudowire the value is always: 76.

Field 03C 03D

Description This parameter identifies the unique plain ethernet interface object in the BTS. Value is always 1. "FIIB, FILB, FTIA, FTIB, FTJA, FTLB" are supported for IEIF-1. "FTFB" are supported for IEIF-1 only in IubIP and DualIub mode.

This parameter identifies the unique plain ethernet interface object in the BTS. Value is always 1. "FIIB, FILB, FTIA, FTIB, FTJA, FTLB" are supported for IEIF-1. "FTFB, FTIF and FIIF" are sup-ported for IEIF-1 only in IubIP and DualIub mode. "FSM and FSI" are sup-ported for IEIF-1 in IubIP mode.

Field 03C 03D

Description This parameter holds the list of the physical interfaces used by the IMA group. The maximum number of interfaces in one IMA group depends on the unit type: FIIB, FILB, FTIA, FTIB, FTJA, FTLB: 4 FTEB, FTPB, FTFA: 8 FTFA, FTHA, FTFB: 16

This parameter holds the list of the physical interfaces used by the IMA group. The maximum number of interfaces in one IMA group depends on the unit type: FIIB, FILB, FTIA, FTIB, FTJA, FTLB: 1..4 FTEB, FTPB, FTFA, FTIF, FIIF: 1..8 FTFA, FTHA, FTFB: 1..16

36 DN70577885



Summary of changes

INTPntpAccessId (NTP Identifier)

IPNOipNodeId (IP Node Identifier)

omsTls (TLS usage towards the O&M system)

uPlaneIpInterface (User-plane application IP network interface)

IPRMiprmId (IP Restricted Mode Identifier)

IPRTipRoutingTableId (IP Routing Table Identifier)

Field 03C 03D

Description Identifies the NTP entity on the FTM. It is always 1.

This parameter identifies the unique NTP configuration entity of the BTS. The value is always 1.

Field 03C 03D

Description This parameter identifies the BTS trans-port IP node configuration. The value is always 1.

This parameter identifies the BTS trans-port IP node configuration. The value is always 1.

Field 03C 03D

Default value 2 0

Field 03C 03D

Related parameters uPlaneIpAddress of IPNO - Parameter uPlaneIpInterface must be configured in case parameter uPlaneIpAddress is a virtual IP address.

uPlaneIpAddress of IPNO - Parameter uPlaneIpInterface must be configured in case parameter uPlaneIpAddress and uPlane2IpAddress are virtual IP addresses.

uPlane2IpAddress of IPNO - Parameter uPlaneIpInterface must be configured in case parameter uPlaneIpAddress and uPlane2IpAddress are virtual IP addresses.

Field 03C 03D

Description This parameter identifies the restricted mode configuration of the BTS. Only one configuration exist. The value of iprmId is always 1.

This parameter identifies the firewall con-figuration of the BTS. The value is always 1.

DN70577885 37



IVIFvlanIfNetId (VLAN interface object identifier)

L2SWIswitchId (Layer 2 Switch Object Identifier)

priorityQueuePcp0 (Priority queue for ethernet frames with VLAN PCP bits 0)


Field 03C 03D

Description Identifies the IP routing entity on the FTM. Instance 1 shall only be used for DCN routing, instance 2 shall be used for IP routing. IPRT-1 is not supported in IubIP. "FTEB, FTHA, FTPB, FTFA and FTFB" are not supported for IPRT-2 in AtmIub mode.

This parameter identifies an IP routing table of the BTS. Instance 1 shall only be used for DCN routing, instance 2 shall be used for IP routing. IPRT-1 is not supported in IubIP. "FTEB, FTHA, FTPB, FTFA, FTFB, FTIF and FIIF" are not supported for IPRT-2 in AtmIub mode. "FSM and FSI" are sup-ported for IPRT-2 only in IubIP mode.

Field 03C 03D

Description This parameter identifies the VLAN inter-face object. Value is 1 to 7. In case of IubIP up to 6 VLANs may exist on the FTM. In case of Dual Iub, up to 5 VLANs may exist on the FTM. One of the interfaces is intended to be reserved for FlexiPacket Radio Man-agement. One of the interfaces is intended to be reserved for CES over PSN.

This parameter identifies the VLAN inter-face object. Value range is 1 to 7. Up to 6 VLANs may exist in IP Iub mode. Up to 5 VLANs may exist in Dual Iub mode. One of the VLAN interfaces is intended to be reserved for FlexiPacket Radio Management. One of the VLAN interfaces is intended to be reserved for CES over PSN.

Field 03C 03D

Description This parameter identifies the layer 2 switch. The value is always 1.

This parameter identifies the BTS trans-port layer 2 switch. The value is always 1.

Field 03C 03D

Description This parameter specifies which priority queue shall be used for ethernet frames with VLAN PCP bits value 0. The range is 1-6 for FTLB and 1-4 for all others.

This parameter specifies which priority queue shall be used for ethernet frames with VLAN PCP bits value 0. The range is 1-6 for FTLB, FSMr3 and 1-4 for all others.

38 DN70577885



Summary of changes





Field 03C 03D



Field 03C 03D



Field 03C 03D



Field 03C 03D



DN70577885 39





priorityQueueNonIP (Priority queue for non-IP frames)

priorityQueueUntagged (Priority queue for untagged ethernet frames)

Field 03C 03D



Field 03C 03D



Field 03C 03D



Field 03C 03D

Description This parameter specifies which priority queue shall be used for non-IP frames. Non-IP frames examples are ARP-, Ethernet OAM- and Synchronous Ethernet messages. The range is 1-6 for FTLB and 1-4 for all others.

This parameter specifies which priority queue shall be used for non-IP frames. Non-IP frames examples are ARP-, Ethernet OAM- and Synchronous Ethernet messages. The range is 1-6 for FTLB, FSMr3 and 1-4 for all others.

40 DN70577885



Summary of changes

OAMMAassocId (Maintenance association identifier)

OAMMDdomainId (Maintenance domain identifier)

OAMMEPccmTxPeriod (Continuity Check Messages transmission period)

OAMPRFprofileId (Profile instance identifier)

Field 03C 03D

Description This parameter specifies which priority queue shall be used for untagged ethernet frames. The range is 1-6 for FTLB and 1-4 for all others.

This parameter specifies which priority queue shall be used for untagged ethernet frames. The range is 1-6 for FTLB, FSMr3 and 1-4 for all others.

Field 03C 03D

Description This parameter identifies a Maintenance Association. Up to 15 associations may exist in the BTS.

This parameter identifies an Ethernet service OAM maintenance association. Up to 15 associations may exist in the BTS.

Field 03C 03D

Description This parameter identifies a Maintenance Domain. Up to 10 domains may exist on the FTM.

This parameter identifies an Ethernet service OAM maintenance domain. Up to 10 domains may exist on the BTS.

Field 03C 03D

Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.

enableCcm of OAMMEP - Parameter ccmTxPerdiod cannot be modified online in case parameter enableCcm has value true.

iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.

Field 03C 03D

Description This parameter identifies a Link OAM profile.

This parameter identifies an Ethernet link OAM profile.

DN70577885 41



OSPFV2ospfRouterId (OSPF router identification)

P3LPmruSize (Maximum Receive Unit (MRU) size)

P3MLmrruSize (Maximum Receive Reconstructed Unit (MRRU) size)

Field 03C 03D



ospfEnabled of OSPFV2 - "ospfRouterId" should be overwritten if ospfEnabled is true and areaId is 0.0.0.0.

Field 03C 03D

Description This parameter specifies maximum receive unit size in octets. A LCP MRU Configure-Request shall be sent automatically when a different value than the default 1500 bytes is set for parameter mruSize. Otherwise no Configure-Request shall be sent. The BTS sends an alarm is the size of a received packet surpasses the mruSize.

This parameter specifies maximum receive unit size in octets. A LCP MRU Configure-Request shall be sent automatically when a different value than the default 1500 bytes is set for parameter mruSize. Otherwise no Configure-Request shall be sent. For IHSPA the maximum mruSize is 1600. The BTS sends an alarm is the size of a received packet surpasses the mruSize.

Range and step 1500 (PACKET_SIZE_1500), 1520 (PACKET_SIZE_1520), 1540 (PACKET_SIZE_1540), 1560 (PACKET_SIZE_1560), 1580 (PACKET_SIZE_1580), 1600 (PACKET_SIZE_1600), 1604 (PACKET_SIZE_1604), 1620 (PACKET_SIZE_1620), 1630 (PACKET_SIZE_1630)

1500 (PACKET_SIZE_1500), 1520 (PACKET_SIZE_1520), 1540 (PACKET_SIZE_1540), 1560 (PACKET_SIZE_1560), 1580 (PACKET_SIZE_1580), 1600 (PACKET_SIZE_1600), 1620 (PACKET_SIZE_1620), 1630 (PACKET_SIZE_1630)

42 DN70577885



Summary of changes

PPPTinterfaceNumber (Interface Number)

pdhPSTTPId (PDH Interface Identifier)

Field 03C 03D

Description This parameter specifies maximum receive reconstructed unit size in octets. The MRRU option shall always be sent as part of every LCP negotiation and applies to then to the bundle. The BTS sends an alarm is the size of a received packet surpasses the mrru-Size.

This parameter specifies maximum receive reconstructed unit size in octets. The MRRU option shall always be sent as part of every LCP negotiation and applies to then to the bundle. For IHSPA the maximum mruSize is 1600. The BTS sends an alarm is the size of a received packet surpasses the mrru-Size.

Range and step 1500 (PACKET_SIZE_1500), 1520 (PACKET_SIZE_1520), 1540 (PACKET_SIZE_1540), 1560 (PACKET_SIZE_1560), 1580 (PACKET_SIZE_1580), 1600 (PACKET_SIZE_1600), 1604 (PACKET_SIZE_1604), 1620 (PACKET_SIZE_1620), 1630 (PACKET_SIZE_1630)

1500 (PACKET_SIZE_1500), 1520 (PACKET_SIZE_1520), 1540 (PACKET_SIZE_1540), 1560 (PACKET_SIZE_1560), 1580 (PACKET_SIZE_1580), 1600 (PACKET_SIZE_1600), 1620 (PACKET_SIZE_1620), 1630 (PACKET_SIZE_1630)

Field 03C 03D

Description Defines the interface location on the unit. The number of interfaces depends on the unit type. FTEB, FTPB: 1..8 FIIB, FILB, FTIA, FTIB, FTJA, FTLB: 1..4 FTFB, FTHA, FTFA: 1..16

Defines the interface location on the unit. The number of interfaces depends on the unit type. FTEB, FTPB, FTIF, FIIF: 1..8 FIIB, FILB, FTIA, FTIB, FTJA, FTLB: 1..4 FTFB, FTHA, FTFA: 1..16

DN70577885 43



QOSqosId (Quality of Service Configuration Identifier)

trafficType (Traffic type)

Field 03C 03D

Description Identifies a PDH interface. Format: unit#-if# The value of unit# is always 1. The value range for the interface number (if#) depends on the unit type: FTEB, FTPB: 1..8 FIIB, FILB, FTIA, FTIB, FTJA, FTLB: 1..4 FTFB, FTHA, FTFA: 1..16

This parameter identifies a PDH inter-face. Format: unit#-if# where unit# = slot number of the unit con-taining the PDH interfaces, and if# = the interface number of the physical interface on the unit and for FIIB/FILB/FTIA/FTIB/FTJA/FTLB, unit#: 1 : This is always 1, since there is only 1 slot. if#: 1..4 for FTFB/FTHA/FTFA, unit#: 1 : This is always 1, since there is only 1 slot. if#: 1..16 for FTEB/FTPB/FTIF/FIIF, unit#: 1 : The slot number is '1', since this is an additional unit if#: 1..8 : Value range is 1..8 for IF1..IF8 on this unit

Field 03C 03D

Description This parameter identifies the unique instance of the QOS class of the BTS. Value always 1.

This parameter identifies the BTS trans-port Quality of Service (QOS) configura-tion. The value is always 1.

44 DN70577885



Summary of changes

DN70577885 45



Field 03C 03D

Description This parameter designates a traffic type. Values for transport mode AtmOv-erEthernet: "TOP" "SG1" - Pseudowire (PW) for per-HopBehaviour (pHB) EF "SG2" - PW for pHB AF4 "SG3" - PW for pHB AF3 "SG4" - PW for pHB AF2 "SG5" - PW for pHB AF1 "SG6" - PW for pHB BE "ICMP" Values for transport mode Iub IP: "DCN" "NBAP" "TOP" "SG1" - Signalled traffic for pHB EF "SG2" - Signalled traffic for pHB AF4 "SG3" - Signalled traffic for pHB AF3 "SG4" - Signalled traffic for pHB AF2 "SG5" - Signalled traffic for pHB AF1 "SG6" - Signalled traffic for pHB BE "ICMP" "CES1" to "CES4" - For mapping DSCP values to vlanPrio bits (on FIIB,FILB,FTIB,FTLB units only) "CES1" to "CES8" - For mapping DSCP values to vlanPrio bits (on FTFB unit only) "BFD1" to "BFD16" "OSPF" (on FIIB,FILB,FTIA,FTIB,FTJA,FTLB,FTFB units only) In iHSPA mode all of Iub IP mode traffic types are supported except for "CES", "BFD" and "OSPF" types. Values for transport mode Dual Iub: "TOP" "SG1" - Signalled traffic for pHB EF "SG2" - Signalled traffic for pHB AF4 "SG3" - Signalled traffic for pHB AF3 "SG4" - Signalled traffic for pHB

This parameter designates a traffic type. Values for transport mode AtmOv-erEthernet: "TOP" "SG1" - Pseudowire (PW) for per-HopBehaviour (pHB) EF "SG2" - PW for pHB AF4 "SG3" - PW for pHB AF3 "SG4" - PW for pHB AF2 "SG5" - PW for pHB AF1 "SG6" - PW for pHB BE "ICMP" Values for transport mode Iub IP: "DCN" "NBAP" "TOP" "SG1" - Signalled traffic for pHB EF "SG2" - Signalled traffic for pHB AF4 "SG3" - Signalled traffic for pHB AF3 "SG4" - Signalled traffic for pHB AF2 "SG5" - Signalled traffic for pHB AF1 "SG6" - Signalled traffic for pHB BE "ICMP" "CES1" to "CES4" - For mapping DSCP values to vlanPrio bits (on FIIB,FILB,FTIB,FTLB units only) "CES1" to "CES8" - For mapping DSCP values to vlanPrio bits (on FTFB, FIIF, FTIF unit only) "BFD1" to "BFD16" "OSPF" (on FIIB,FILB,FTIA,FTIB,FTJA,FTLB,FTFB, FSM, FSI, FIIF, FTIF units only) Values for transport mode Dual Iub: "TOP" "SG1" - Signalled traffic for pHB EF "SG2" - Signalled traffic for pHB AF4 "SG3" - Signalled traffic for pHB AF3 "SG4" - Signalled traffic for pHB AF2 "SG5" - Signalled traffic for pHB AF1

46 DN70577885



Summary of changes

STPGinterfaceNumber (Interface number)

timingGenPgId (Synchronisation Protection Group Identifier)

unitNumber (Unit number)

Description (cont.) AF2 "SG5" - Signalled traffic for pHB AF1 "SG6" - Signalled traffic for pHB BE "ICMP" "BFD1" to "BFD16" "OSPF" (on FIIB,FILB,FTIA,FTIB,FTJA,FTLB,FTFB units only)

"SG6" - Signalled traffic for pHB BE "ICMP" "BFD1" to "BFD16" "OSPF" (on FIIB,FILB,FTIA,FTIB,FTJA,FTLB,FTFB, FIIF, FTIF units only)

Field 03C 03D

Field 03C 03D

Description This parameter specifies - either the physical location of the PDH interface location on the unit (value range 1..16) for a PDH clock source - or the physical location of the SDH interface location on the unit (value is always 1) for a SDH clock source - or the physical location of the ethernet interface of the unit (value range 1..3) for the synchronous ethernet clock source. In case of Time Over Packet the BTS automatically selects the ethernet link. The parameter is ignored. The parameter is ignored also, if the external clock is used.

This parameter specifies either - the PDH interface on the unit for a PDH synchronization source, or - the SDH interface on the unit for a SDH clock source, or - the Ethernet interface on the unit for the synchronous Ethernet synchroni-zation source. In case of Timing over Packet the BTS automatically selects the Ethernet link. This parameter is ignored. In case the external clock is selected as synchronization source the parameter is ignored by the BTS. Recom-mended value is 0 in this case. Examples: interfaceNumber=1, unitNum-ber=1, clockProtocol=clkPDH: This means PDH interface number 1 on unit 1. interfaceNumber=1, unitNum-ber=1, clockProtocol=clkSyncE: This means Ethernet interface number 1 on unit 1.

Field 03C 03D

Description Identifies the Synchronisation Protection Group. The value is always 1.

This parameter identifies the BTS trans-port synchronisation protection group. The value is always 1.

DN70577885 47



TCTTinterfaceNumber (Interface number)

TWAMPmessageSize (TWAMP initiator message size)

UNITunitTypeExpected (Expected hardware unit type)

Field 03C 03D

Description Specifies the location of the unit on which the clock source is running. In this release it is always 1.

This parameter specifies the location of the unit providing the synchronisation source interface.


Default value 1

Field 03C 03D



Field 03C 03D

Default value notes Default value is 100 octets.

48 DN70577885



Summary of changes

unitTypeActual (Installed hardware unit type)

Field 03C 03D

Description This parameter specifies the type of the hardware unit that is expected to be installed in the FTM slot. Values are: FTPB: 470137A FTEB: 470156A FTFA: 470134A FTHA: 471522A FTIA: 471025A FTIB: 471720A FTJA: 471248A FTOA: 470133A FTLB: 471984A FTFB: 472036A FIIB: 472271A FILB: 472294A

This parameter specifies the type of the hardware unit that is expected to be installed in the FTM slot. Values are: System Module Release 2: FIIB: 472271A FILB: 472294A FTEB: 470156A FTFA: 470134A FTFB: 472036A FTHA: 471522A FTIA: 471025A FTIB: 471720A FTJA: 471248A FTLB: 471984A FTOA: 470133A FTPB: 470137A System Module Release 3: FSM: Outdoor System Module FSI: Indoor System Module FTIF: 472311A FIIF: 472355A Flexi BTS support: FQGA:472467A

Range and step 0 (470137A), 1 (470156A), 2 (470134A), 3 (471522A), 4 (471025A), 5 (471720A), 6 (471248A), 7 (470133A), 8 (471984A), 9 (472036A), 10 (472271A), 11 (472294A)

0 (470137A), 1 (470156A), 2 (470134A), 3 (471522A), 4 (471025A), 5 (471720A), 6 (471248A), 7 (470133A), 8 (471984A), 9 (472036A), 10 (472271A), 11 (472294A), 12 (FSM), 14 (FSI), 16 (472311A), 17 (472355A), 18 (472467A)

DN70577885 49



unitId (Unit Identifier)

VCCTinterfaceNumber (Interface Number)

Field 03C 03D

Description This parameter shows the type of the hardware unit that is installed in the FTM slot. Values are: FTPB: 470137A FTEB: 470156A FTFA: 470134A FTHA: 471522A FTIA: 471025A FTIB: 471720A FTJA: 471248A FTOA: 470133A FTLB: 471984A FTFB: 472036A FIIB: 472271A FILB: 472294A

This parameter shows the type of the hardware unit that is installed in the FTM slot. Values are: System Module Release 2: FIIB: 472271A FILB: 472294A FTEB: 470156A FTFA: 470134A FTFB: 472036A FTHA: 471522A FTIA: 471025A FTIB: 471720A FTJA: 471248A FTLB: 471984A FTOA: 470133A FTPB: 470137A System Module Release 3: FSM: Outdoor System Module FSI: Indoor System Module FTIF: 472311A FIIF: 472355A Flexi BTS support: FQGA:472467A

Field 03C 03D

Description Specifies the location of the unit. In this release it is always 1.

This parameter identifies the unit location as the slot number containing the hardware unit of BTS transport.

50 DN70577885



Summary of changes

VCTTinterfaceNumber (Interface Number)

VPCTinterfaceNumber (Interface Number)

Field 03C 03D



Field 03C 03D



Field 03C 03D



DN70577885 51



VPTTinterfaceNumber (Interface Number)

Removed parametersP3LP

– shortSeqNrOn (Short sequence numbering flag)

Field 03C 03D



52 DN70577885



Introduction

1 IntroductionThis document describes the Flexi Transport Module Parameters used in WBTS WN7.0 1.0 and WN7.0 2.0 release.

For detailed information on changes between Flexi Transport Module Parameters WBTS7.0 1.0 and WBTS6.0 parameters, see the WCDMA RAN, Rel. RU30, Changes document.

g If there is a difference in range/default value between WN7.0 2.0 and WN7.0 1.0 param-eters, or when a parameter is specific only to one of these releases, it is indicated in the description of the parameter.

Please note the following definitions for the Range, Step and Unit values used in the parameter tables:

• Range: The user interface value range for the parameter. If unit is character then range specifies number of characters in string (minimum number - maximum number).

• Step: The value by which the parameter value increases or decreases within the range.

• Unit: The measurement unit in use for the range and step, for example, s (second), min (minute), h (hour), m (meter), km (kilometer), dB (decibel), dBm, bit/s (bit per second), kbit/s (kilobit per second), character, % (per cent), per mil, period. If no unit is given, it means that the value range has no measurement unit or the parameter value cannot be changed in steps.

DN70577885 53

Flexi Transport Module Parameters A2NE Parameters


2 A2NE Parameters

2.1 aal2NodeId (AAL2 Node Identifier)

Parameter name AAL2 Node Identifier

Abbreviated name aal2NodeId

3GPP name -

Managed Object A2NE

Multiplicity 1

Description This parameter identifies the BTS AAL2 node. Because BTS transport represents a single AAL2 node, the identifier is always 1.

Range 1... 1

Step 1

Units -

Formula for getting internal value

internal_value = gui_value

Default value -

Default value notes -

Related functions -

Modification Not modifiable

Related parameters -

Parameter relationships -

Related options -

Feature dependencies -

Interfaces – EM <-> FTM– RAC -> FTM– RAC <-> RACApp

References -

Table 1 aal2NodeId (AAL2 Node Identifier)

54 DN70577885



A2ST Parameters

3 A2ST Parameters

3.1 AAL2EndAddress (AAL2 End Address)

3.2 VCI (Virtual Channel Identifier)

Parameter name AAL2 End Address

Abbreviated name AAL2EndAddress

3GPP name -

Managed Object A2ST

Multiplicity 1

Description AAL2 endpoint address (A2EA) for a signalling link.

The value has to be the same as the one configured in the RNC.

Range 40

Step -

Units characters



Default value -


Related functions -

Modification On-Line



Related options -


Interfaces – EM <-> FTM– RAC <-> FTM– RAC <-> RACApp

References -

Table 2 AAL2EndAddress (AAL2 End Address)

Parameter name Virtual Channel Identifier

Abbreviated name VCI

3GPP name -

Table 3 VCI (Virtual Channel Identifier)

DN70577885 55

Flexi Transport Module Parameters A2ST Parameters


3.3 VPI (Virtual Path Identifier)

Managed Object A2ST

Multiplicity 1

Description Virtual Channel Identifier.

Range 32... 4095

Step 1

Units -



Default value -


Related functions -




Related options -


Interfaces – FTM -> EM– FTM -> RAC

References -

Table 3 VCI (Virtual Channel Identifier) (Cont.)

Parameter name Virtual Path Identifier

Abbreviated name VPI

3GPP name -

Managed Object A2ST

Multiplicity 1

Description Virtual Path Identifier.

Range 0... 255

Step 1

Units -



Default value -


Table 4 VPI (Virtual Path Identifier)

56 DN70577885



A2ST Parameters

3.4 aal2sigTTPId (AAL2 Signalling Link Identifier)

Related functions -




Related options -



References -

Table 4 VPI (Virtual Path Identifier) (Cont.)

Parameter name AAL2 Signalling Link Identifier

Abbreviated name aal2sigTTPId

3GPP name -

Managed Object A2ST

Multiplicity 1

Description This parameter identifies the AAL2 signalling link.

The identifier is composed from the elements:

- Unit number (unit#)

- Interface number(if#, imag# or pw#)

- Virtual Path Identifier (vpi#)

- Virtual Channel Identifier (vci#)

Format:

- unit#-if#-vpi#vci# (e.g. 1-8-000C0)

- unit#-imag#-vpi#vci# (e.g. 1-34-00210)

Range:

unit#: 1

if#: 1..16 (maxi. 2 digits)

imag#: 33..75 (2 digits)

pw#: 76

vpi#: 00..FF (hexadecimal number, 2 digits)

vci#: 000..FFF (hexadecimal number, 3 digits)

Range 9...10

Step -

Table 5 aal2sigTTPId (AAL2 Signalling Link Identifier)

DN70577885 57



3.5 interfaceNumber (Interface Number)

Units characters



Default value -


Related functions -


Related parameters VCI of A2ST

VPI of A2ST

interfaceNumber of A2ST

unitNumber of A2ST

Parameter relationships The A2ST id is composed of the values of these other attributes

Related options -



References -

Table 5 aal2sigTTPId (AAL2 Signalling Link Identifier) (Cont.)

Parameter name Interface Number

Abbreviated name interfaceNumber

3GPP name -

Managed Object A2ST

Multiplicity 1

Description Defines the location of the physical interface on the unit.

The value range depends on the unit type.

FTEB, FTPB, FTIF, FIIF: 1..8

FIIB, FILB, FTIA, FTIB, FTJA, FTLB: 1..4

FTFB, FTFA, FTHA: 1..16

In case of Inverse Multiplexing for ATM (IMA) the value range is: 33..75.

For ATM over Ethernet, the value is always: 76.

Table 6 interfaceNumber (Interface Number)

58 DN70577885



A2ST Parameters

3.6 stcAlarmEnable (Signalling Transport Converter Alarm Enable)

Range 1... 76

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 6 interfaceNumber (Interface Number) (Cont.)

Parameter name Signalling Transport Converter Alarm Enable

Abbreviated name stcAlarmEnable

3GPP name -

Managed Object A2ST

Multiplicity 1

Description Enables or disables alarm 61260 "STC connection to signalling peer not established". If enabled, the FTM observes the availability of the adjacent node's signalling link.

Range false (0), true (1)

Step -

Units -


– false => 0 – true => 1

Default value false (0)

Table 7 stcAlarmEnable (Signalling Transport Converter Alarm Enable)

DN70577885 59



3.7 unitNumber (Unit Number)


Related functions -




Related options -



References -

Table 7 stcAlarmEnable (Signalling Transport Converter Alarm Enable) (Cont.)

Parameter name Unit Number

Abbreviated name unitNumber

3GPP name -

Managed Object A2ST

Multiplicity 1

Description Specifies the location of the unit (slot number). In this release it is always 1. The BTS has only 1 unit in slot 1.

Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -


Table 8 unitNumber (Unit Number)

60 DN70577885



A2ST Parameters


References -

Table 8 unitNumber (Unit Number) (Cont.)

DN70577885 61

Flexi Transport Module Parameters A2UT Parameters


4 A2UT Parameters





3GPP name -

Managed Object A2UT

Multiplicity 1


Range 32... 4095

Step 1

Units -



Default value -


Related functions -




Related options -



References -




3GPP name -

Managed Object A2UT

Multiplicity 1



62 DN70577885



A2UT Parameters

4.3 aal2pathTTPId (AAL2 User Path Identifier)

Range 0... 255

Step 1

Units -



Default value -


Related functions -




Related options -



References -


Parameter name AAL2 User Path Identifier

Abbreviated name aal2pathTTPId

3GPP name -

Managed Object A2UT

Multiplicity 1

Table 11 aal2pathTTPId (AAL2 User Path Identifier)

DN70577885 63



Description Identifies the AAL2 User Path.

The object is identified by

- Unitnumber (unit#)

- Interfacenumber(if#, imag# or pw#)



Format:



Range:

unit#: 1



pw#: 76



Range 9...10

Step -

Units characters



Default value -


Related functions -


Related parameters VCI of A2UT

VPI of A2UT

interfaceNumber of A2UT

unitNumber of A2UT

Parameter relationships The A2UT id is composed of the values of these other attributes

Related options -



References -

Table 11 aal2pathTTPId (AAL2 User Path Identifier) (Cont.)

64 DN70577885



A2UT Parameters


4.5 pid (Path Identifier)



3GPP name -

Managed Object A2UT

Multiplicity 1








Range 1... 76

Step 1

Units -



Default value -


Related functions -




Related options -



References -


Parameter name Path Identifier

Table 13 pid (Path Identifier)

DN70577885 65



4.6 queue2Weight (Weight of AAL2 user path queue Q2)

Abbreviated name pid

3GPP name -

Managed Object A2UT

Multiplicity 1

Description Associates AAL2 signalling messages to the VCC (AAL2 user path) that has been selected as the carrier for the AAL2 connection.

The PID is unique for each AAL2 signalling link (A2ST, ANI).

Range 0... 99999999

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 13 pid (Path Identifier) (Cont.)

Parameter name Weight of AAL2 user path queue Q2

Abbreviated name queue2Weight

3GPP name -

Managed Object A2UT

Multiplicity 1

Description This is the weight of AAL2 User Path queue Q2.

Range 1... 1000

Table 14 queue2Weight (Weight of AAL2 user path queue Q2)

66 DN70577885



A2UT Parameters


Step 1

Units -



Default value 1000


Related functions -




Related options – RAN1253 Iub Transport QoS



References -

Table 14 queue2Weight (Weight of AAL2 user path queue Q2) (Cont.)



3GPP name -

Managed Object A2UT

Multiplicity 1


Range 1... 1000

Step 1

Units -



Default value 500


Related functions -




DN70577885 67








References -

Table 15 queue3Weight (Weight of AAL2 user path queue Q3) (Cont.)



3GPP name -

Managed Object A2UT

Multiplicity 1


Range 1... 1000

Step 1

Units -



Default value 1


Related functions -







References -


68 DN70577885



A2UT Parameters




3GPP name -

Managed Object A2UT

Multiplicity 1


Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -



References -


DN70577885 69

Flexi Transport Module Parameters ACCP Parameters


5 ACCP Parameters

5.1 atmAccessProfileId (ATM Access Profile Identifier)

5.2 egressBandwidth (Egress Bandwidth)

Parameter name ATM Access Profile Identifier

Abbreviated name atmAccessProfileId

3GPP name -

Managed Object ACCP

Multiplicity 1

Description Identifies the ATM Access Profile. The value is always 1. Exactly 1 ATM access profile exists on the BTS for the ATM over Ethernet interface.

Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 18 atmAccessProfileId (ATM Access Profile Identifier)

Parameter name Egress Bandwidth

Abbreviated name egressBandwidth

3GPP name -

Table 19 egressBandwidth (Egress Bandwidth)

70 DN70577885



ACCP Parameters

Managed Object ACCP

Multiplicity 1

Description Defines the maximum allowed egress bandwidth in cells per second for a logical ATM interface.

The value range of egressBandwidth is as follows:

- E1: fixed value 4528

- T1/JT1: fixed value 3622

- STM-1: 36..144896, step 1, default 144896 (32 x E1)

- ATM over Ethernet (pseudowire): 1132..144896, step 1132, default 144896.

- IMA E1: fixed value: int[n*4526*(m-1)/m] where m = Tx Frame Length and n = number of IMA links in a group

- IMA T1/JT1 fixed value: int[n*3621*(m-1)/m] where m = Tx Frame Length and n = number of IMA links in a group

Range 36... 144896

Step 1

Units cells/s



Default value 144896

Default value notes The range, step and default value of the parameter depend on the interface type.The default value of 144896 e.g. applies only to Pseudowire and STM-1. See the description of the parameter for more details.

Related functions -




Related options -



References -

Table 19 egressBandwidth (Egress Bandwidth) (Cont.)

DN70577885 71

Flexi Transport Module Parameters ACCP Parameters


5.3 ingressBandwidth (Ingress Bandwidth)

Parameter name Ingress Bandwidth

Abbreviated name ingressBandwidth

3GPP name -

Managed Object ACCP

Multiplicity 1

Description Defines the maximum allowed ingress bandwidth in cells per second for a logical ATM interface.

For the following interfaces the values are fixed:

- E1: 4528

- STM-1: 144896 (32 x E1)

- T1/JT1: 3622

- IMA E1: int[n*4526*(m-1)/m] where m = Tx Frame Length and n = number of IMA links in a group

- IMA T1/JT1: int[n*3621*(m-1)/m] where m = Tx Frame Length and n = number of IMA links in a group

For ATM over Ethernet (Pseudowire tunnel) the value is operator configurable from 1132 to 144896 in steps of 1132.

Range 1132... 144896

Step 1132

Units cells/s




Default value notes Range and step and default value refer only to ATM over Ethernet, because this is the only case where the parameter is configurable. For the other cases always the values from the "description" apply.

Related functions -




Related options -


Table 20 ingressBandwidth (Ingress Bandwidth)

72 DN70577885



ACCP Parameters


References -

Table 20 ingressBandwidth (Ingress Bandwidth) (Cont.)

DN70577885 73

Flexi Transport Module Parameters AMGR Parameters


6 AMGR Parameters

6.1 amgrId (Account Manager Identifier)

6.2 ldapConnectionType (LDAP Server TLS access mode)

Parameter name Account Manager Identifier

Abbreviated name amgrId

3GPP name -

Managed Object AMGR

Multiplicity 1

Description This parameter identifies the BTS account manager configuration. The value is always 1.

Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 21 amgrId (Account Manager Identifier)

Parameter name LDAP Server TLS access mode

Abbreviated name ldapConnectionType

3GPP name -

Managed Object AMGR

Table 22 ldapConnectionType (LDAP Server TLS access mode)

74 DN70577885



AMGR Parameters

6.3 primaryLdapPort (Port Number of Primary LDAP Server)

Multiplicity 1

Description This parameter holds the TLS access mode for the LDAP server(s) of the BTS. Values are "TLS" (allow only secured connections) and "TLS_OR_PLAIN_TEXT" (allow both unsecured and secured connections).

Range TLS (0), TLS_OR_PLAIN_TEXT (1)

Step -

Units -


gui ==> internal

TLS ==> 0

TLS_OR_PLAIN_TEXT ==> 1

Default value TLS (0)


Related functions -




Related options – RAN1314 Secure LDAP



References -

Table 22 ldapConnectionType (LDAP Server TLS access mode) (Cont.)

Parameter name Port Number of Primary LDAP Server

Abbreviated name primaryLdapPort

3GPP name -

Managed Object AMGR

Multiplicity 1

Description The port number of the Primary LDAP Server.

Range 1... 65535

Step 1

Units -

Table 23 primaryLdapPort (Port Number of Primary LDAP Server)

DN70577885 75

Flexi Transport Module Parameters AMGR Parameters


6.4 primaryLdapServer (IP address of Primary LDAP Server)



Default value 389

Default value notes standard port for LDAP

Related functions -




Related options -



References -

Table 23 primaryLdapPort (Port Number of Primary LDAP Server) (Cont.)

Parameter name IP address of Primary LDAP Server

Abbreviated name primaryLdapServer

3GPP name -

Managed Object AMGR

Multiplicity 1

Description The IP address of the Primary LDAP Server, as dotted decimal string.

Range 7...15

Step -

Units characters



Default value -


Related functions -




Table 24 primaryLdapServer (IP address of Primary LDAP Server)

76 DN70577885



AMGR Parameters

Related options -



References -

Table 24 primaryLdapServer (IP address of Primary LDAP Server) (Cont.)

DN70577885 77

Flexi Transport Module Parameters ANBA Parameters


7 ANBA Parameters





3GPP name -

Managed Object ANBA

Multiplicity 1


Range 32... 4095

Step 1

Units -



Default value -


Related functions -




Related options -



References -




3GPP name -

Managed Object ANBA

Multiplicity 1



78 DN70577885



ANBA Parameters

7.3 interfaceNumber (Interface Identifier)

Range 0... 255

Step 1

Units -



Default value -


Related functions -




Related options -



References -


Parameter name Interface Identifier


3GPP name -

Managed Object ANBA

Multiplicity 1

Description Defines the location on the unit of the physical inter-face that carries the signallink link.

The value depends on the unit type.


FTIA, FTIB, FTJA, FTLB: 1..4

FTFA, FTHA: 1..16

For IMA, the parameter identifies the IMA group. Values are: 33..75.

For the ATM over Ethernet pseudowire the value is always: 76.

Range 1... 76

Step 1

Table 27 interfaceNumber (Interface Identifier)

DN70577885 79



7.4 nbapTTPId (Upper Layer Path Identifier)

Units -



Default value -


Related functions -




Related options -



References -

Table 27 interfaceNumber (Interface Identifier) (Cont.)

Parameter name Upper Layer Path Identifier

Abbreviated name nbapTTPId

3GPP name -

Managed Object ANBA

Multiplicity 1

Description Identifies the upper layer path. The object is identified by - Unit number (unit#) - Interface number(if#, imag# or pw#) - Virtual Path Identifier (vpi#) - Virtual Channel Identifier (vci#) Format: - unit#-if#-vpi#vci# (e.g. 1-8-000C0) - unit#-imag#-vpi#vci# (e.g. 1-34-00210) Range: unit#: 1 if#: 1..16 (maxi. 2 digits) imag#: 33..75 (2 digits) pw#: 76 vpi#: 00..FF (hexadecimal number, 2 digits) vci#: 000..FFF (hexadecimal number, 3 digits)

Range 9...10

Table 28 nbapTTPId (Upper Layer Path Identifier)

80 DN70577885



ANBA Parameters

7.5 nbapType (Upper Layer Connection Type)

Step -

Units characters



Default value -


Related functions -


Related parameters VCI of ANBA - The value of parameter VCI is contained in the value of parame-ter nbapTTPId.

VPI of ANBA - The value of parameter VPI is contained in the value of parame-ter nbapTTPId.

interfaceNumber of ANBA - The value of parameter interfaceNumber is contained in the value of parameter nbapTTPId.

unitNumber of ANBA - The value of parameter unitNumber is contained in the value of parameter nbapTTPId.


Related options -



References -

Table 28 nbapTTPId (Upper Layer Path Identifier) (Cont.)

Parameter name Upper Layer Connection Type

Abbreviated name nbapType

3GPP name -

Managed Object ANBA

Multiplicity 1

Table 29 nbapType (Upper Layer Connection Type)

DN70577885 81



Description This parameter defines the Upper Layer Connec-tion Type.

In case of a WCDMA environment this is the NBAP type: it can be either C-NBAP or D-NBAP.

In case of an I-HSPA environment, this is the type of traffic converted to IP and then forwarded to the I-HSPA adapter.

The labels AA0 to AA7 are used for AAL5 on FTLB integrated I-HSPA.

Range C_NBAP (0), D_NBAP (1), IUR_C_PLANE (2), IUR_U_PLANE (3), IUPS_C_PLANE (4), IUPS_U_PLANE (5), AA0 (6), AA1 (7), AA2 (8), AA3 (9), AA4 (10), AA5 (11), AA6 (12), AA7 (13)

Step -

Units -


gui ==> internal

C_NBAP ==> 0

D_NBAP ==> 1

IUR_C_PLANE ==> 2

IUR_U_PLANE ==> 3

IUPS_C_PLANE ==> 4

IUPS_U_PLANE ==> 5

AA0 ==> 6

AA1 ==> 7

AA2 ==> 8

AA3 ==> 9

AA4 ==> 10

AA5 ==> 11

AA6 ==> 12

AA7 ==> 13

Default value -


Related functions -


Related parameters iHSPAmode of IPNO - If iHS-PAmode is set to enabled then only the enum values starting with AA are supported.


Related options -

Table 29 nbapType (Upper Layer Connection Type) (Cont.)

82 DN70577885



ANBA Parameters




References -

Table 29 nbapType (Upper Layer Connection Type) (Cont.)



3GPP name -

Managed Object ANBA

Multiplicity 1


Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -



References -


DN70577885 83

Flexi Transport Module Parameters BFD Parameters


8 BFD Parameters

8.1 bfdActivation (BFD session activation flag)

Parameter name BFD session activation flag

Abbreviated name bfdActivation

3GPP name -

Managed Object BFD

Multiplicity 1

Description This parameter activates or deactivates the BFD session.

Activate: if set to value true, the transmission of BFD control packets towards the remote peer is started and, in case the BFD session fails, alarms are raised.

Deactivate: if set to value false, the transmission of BFD control packets towards the remote peer is stopped. Also the BTS discards every received BFD packet for a deactivated BFD instance. Moreover all active alarms related to the BFD session are cleared. The BFD session effectively does not exist at all.


Step -

Units -


– false => 0 – true => 1



Related functions -



function of BFD - This parameter is ignored when the value of "function" parameter is OSPF_ALL or OSPF_IP_IF.


Table 31 bfdActivation (BFD session activation flag)

84 DN70577885



BFD Parameters

8.2 bfdAdminUp (BFD session admin down state control)

Related options – RAN2440 Fast IP Rerouting– RAN1449 Dual Iub for Flexi WCDMA– RAN74 Native Iub IP for Flexi WCDMA BTS



References -

Table 31 bfdActivation (BFD session activation flag) (Cont.)

Parameter name BFD session admin down state control

Abbreviated name bfdAdminUp

3GPP name -

Managed Object BFD

Multiplicity 1

Description This parameter controls the admin state of the BFD session.

If set to false, the session enters the "Down" state. Only control messages with state "Admin Down" are sent to the peer. All active alarms of the BFD session are cleared.

If set to true, the session leaves the "Down" state. It will reach the "Up" state if the remote peer is also in "Up" state. If the BFD session fails, alarms are raised for it.


Step -

Units -


– false => 0 – true => 1

Default value true (1)


Related functions -


Table 32 bfdAdminUp (BFD session admin down state control)

DN70577885 85



8.3 bfdDestAddress (Destination IP address for the BFD session)

Related parameters bfdActivation of BFD - Parameter bfdAdminUp is only relevant if parameter bfdActiva-tion has value true.



Related options – RAN74 Native Iub IP for Flexi WCDMA BTS– RAN1449 Dual Iub for Flexi WCDMA– RAN2440 Fast IP Rerouting



References -

Table 32 bfdAdminUp (BFD session admin down state control) (Cont.)

Parameter name Destination IP address for the BFD session

Abbreviated name bfdDestAddress

3GPP name -

Managed Object BFD

Multiplicity 1

Description This parameter specifies the destination IP address to be used in the BFD session. To be entered in dotted decimal format.

Range 7...15

Step -

Units characters



Default value -


Related functions -


Table 33 bfdDestAddress (Destination IP address for the BFD session)

86 DN70577885



BFD Parameters

8.4 bfdDetectMult (BFD session packets lost detection time multiplier)






References -

Table 33 bfdDestAddress (Destination IP address for the BFD session) (Cont.)

Parameter name BFD session packets lost detection time multiplier

Abbreviated name bfdDetectMult

3GPP name -

Managed Object BFD

Multiplicity 1

Description The negotiated BFD control word transmission interval, multiplied by this parameter, provides the detection time for lost packets in the BFD session. Roughly speaking bfdDetectMult is the number of BFD control packets that the FTM may lose in a row, before it shall declare the BFD session to be down.

Range 2... 10

Step 1

Units -



Default value 5


Related functions -


Table 34 bfdDetectMult (BFD session packets lost detection time multiplier)

DN70577885 87



8.5 bfdGrp (BFD group reference)






References -

Table 34 bfdDetectMult (BFD session packets lost detection time multiplier) (Cont.)

Parameter name BFD group reference

Abbreviated name bfdGrp

3GPP name -

Managed Object BFD

Multiplicity 1

Description This parameter references the BFD group id to which the BFD session belongs.The parameter is a managed object instance iden-tifier (LMOID), referencing an instance of object class BFDGRP. The parameter may remain empty, meaning the BFD session is not bound to a BFD group.

Range 0...40

Step -

Units characters



Default value -

Default value notes Default is the empty string. By default a BFD session is not assigned to any BFD group.

Related functions -


Table 35 bfdGrp (BFD group reference)

88 DN70577885



BFD Parameters

8.6 bfdId (BFD session identifier)


function of BFD - "bfdGrp" parameter shall not be configured (must be left empty) when "function" parameter has value OSPF_ALL or OSPF_IP_IF





References -

Table 35 bfdGrp (BFD group reference) (Cont.)

Parameter name BFD session identifier

Abbreviated name bfdId

3GPP name -

Managed Object BFD

Multiplicity 1

Description This parameter identifies a BFD session.

Range 1... 16

Step 1

Units -



Default value -


Related functions -



Table 36 bfdId (BFD session identifier)

DN70577885 89



8.7 bfdSourceIpAddr (Source IP address for the BFD session)





References -

Table 36 bfdId (BFD session identifier) (Cont.)

Parameter name Source IP address for the BFD session

Abbreviated name bfdSourceIpAddr

3GPP name -

Managed Object BFD

Multiplicity 1

Description This parameter specifies the source IP address to be used in BFD messages for the BFD session. This can be a network interface IP address or a virtual IP address.

To be entered in dotted decimal format.

Range 7...15

Step -

Units characters



Default value -


Related functions -




Table 37 bfdSourceIpAddr (Source IP address for the BFD session)

90 DN70577885



BFD Parameters

8.8 bfdSourceUdpPort (UDP source port of the BFD session)




References -

Table 37 bfdSourceIpAddr (Source IP address for the BFD session) (Cont.)

Parameter name UDP source port of the BFD session

Abbreviated name bfdSourceUdpPort

3GPP name -

Managed Object BFD

Multiplicity 1

Description This parameter specifies the UDP source port to be used in the BFD session.

Note: value range and default value depend on the BFD type.

- For Multi Hop BFD, the value range is 4784, 49152...65535 and the default value = 4784.

- For Single Hop BFD the value range is 3784, 49152...65535 and the default value = 3784.

Range 3784... 65535

Step 1

Units -



Default value 4784

Default value notes Since the default value of BFD Type is Multi Hop BFD, the default BFD UDP source port is 4784.

Related functions -


Table 38 bfdSourceUdpPort (UDP source port of the BFD session)

DN70577885 91



8.9 bfdType (BFD session type)

Related parameters bfdType of BFD - - For Multi Hop BFD, the value range is 4784, 49152...65535 and the default value = 4784.






References -

Table 38 bfdSourceUdpPort (UDP source port of the BFD session) (Cont.)

Parameter name BFD session type

Abbreviated name bfdType

3GPP name -

Managed Object BFD

Multiplicity 1

Description This parameter specifies the type of the BFD session: Single Hop or Multi Hop BFD.

Range singleHopBFD (0), multiHopBFD (1)

Step -

Units -


gui ==> internal

singleHopBFD ==> 0

multiHopBFD ==> 1

Default value multiHopBFD (1)


Related functions -


Table 39 bfdType (BFD session type)

92 DN70577885



BFD Parameters

8.10 desMinTxInt (Desired minimum BFD control word transmit interval)






References -

Table 39 bfdType (BFD session type) (Cont.)

Parameter name Desired minimum BFD control word transmit interval

Abbreviated name desMinTxInt

3GPP name -

Managed Object BFD

Multiplicity 1

Description This parameter specifies the minimum interval, that the FTM would like to use when transmitting BFD control packets for the BFD session.

Range 100... 5000

Step 100

Units ms



Default value 500


Related functions -



Table 40 desMinTxInt (Desired minimum BFD control word transmit interval)

DN70577885 93



8.11 function (BFD session function definition)





References -

Table 40 desMinTxInt (Desired minimum BFD control word transmit interval) (Cont.)

Parameter name BFD session function definition

Abbreviated name function

3GPP name -

Managed Object BFD

Multiplicity 1

Description This parameter defines for which purpose BFD session is used.

If value is set to MANUAL_BFD_SESSION both, bfdSourceIpAddr and bfdDestAddress have to be specified.

If value is set to OSPF_ALL for both, bfdSourceI-pAddr and bfdDestAddress the value has to be set to 0.0.0.0.

If value is set to OSPF_IP_IF the value for bfdSour-ceIpAddr shall match the value of the IP interface used for OSPF. The value for bfdDestAddress has to be set to 0.0.0.0.

Range MANUAL_BFD_SESSION (0), OSPF_ALL (1), OSPF_IP_IF (2)

Step -

Units -


gui ==> internal

MANUAL_BFD_SESSION ==> 0

OSPF_ALL ==> 1

OSPF_IP_IF ==> 2

Default value MANUAL_BFD_SESSION (0)

Table 41 function (BFD session function definition)

94 DN70577885



BFD Parameters

8.12 reqMinRxInt (Required minimum BFD control word receive interval)


Related functions -



unitTypeExpected of UNIT - Since OSPF is not supported on all HW variants, for the HW modules FTEB, FTHA, FTPB, FTFA the only supported value is "MANUAL_BFD_SESSION".


Related options – RAN2440 Fast IP Rerouting– RAN2359 OSPF enhancements


Interfaces – FTM <-> RAC– FTM <-> EM– RACApp <-> RAC

References -

Table 41 function (BFD session function definition) (Cont.)

Parameter name Required minimum BFD control word receive interval

Abbreviated name reqMinRxInt

3GPP name -

Managed Object BFD

Multiplicity 1

Description This parameter specifies the minimum interval between received BFD control packets that the FTM shall support for the BFD session.

Range 100... 5000

Step 100

Units ms



Table 42 reqMinRxInt (Required minimum BFD control word receive interval)

DN70577885 95



Default value 500


Related functions -







References -

Table 42 reqMinRxInt (Required minimum BFD control word receive interval) (Cont.)

96 DN70577885



BFDGRP Parameters

9 BFDGRP Parameters

9.1 bfdGrpId (BFD Group Identifier )

Parameter name BFD Group Identifier

Abbreviated name bfdGrpId

3GPP name -

Managed Object BFDGRP

Multiplicity 1

Description This parameter identifies a BFD group.

Range 1... 8

Step 1

Units -



Default value -


Related functions -







References -

Table 43 bfdGrpId (BFD Group Identifier )

DN70577885 97

Flexi Transport Module Parameters CCFA Parameters


10 CCFA Parameters

10.1 atmFabricId (ATM Fabric Identifier)

Parameter name ATM Fabric Identifier

Abbreviated name atmFabricId

3GPP name -

Managed Object CCFA

Multiplicity 1

Description Since in Flexi there are no actual ATM cross con-nections, the MO ATM Fabric is a dummy, intro-duced just to keep the attribute ubrPlusEnabled on the same place as in AXC.

This parameter identifies the ATM Fabric configura-tion. Values is always 1: Exactly 1 instance of ATM Fabric exists on the BTS.

Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 44 atmFabricId (ATM Fabric Identifier)

98 DN70577885



CCFA Parameters

10.2 ubrPlusEnabled (UBR+ Enabled)

Parameter name UBR+ Enabled

Abbreviated name ubrPlusEnabled

3GPP name -

Managed Object CCFA

Multiplicity 1

Description This attribute is used to explicitly enable (TRUE) or disable (FALSE) the network element to take UBR+ into use. If set to FALSE then the network element ingnores MDCR and UBRshare parameters in the TRDE.

If set to TRUE, the network element uses MDCR and UBR share for UBR+ connection traffic man-agement scheduling. If TRUE and MDCR and UBRshare are not given then the network element shall take the default values for MDCR and UBR-share. The usage of UBR+ requires the availability of a licence.


Step -

Units -


– false => 0 – true => 1



Related functions -




Related options -

Feature dependencies – ATM Traffic Management: UBR (Unspecified Bit Rate), CBR (Constant Bit Rate), Shaping


References -

Table 45 ubrPlusEnabled (UBR+ Enabled)

DN70577885 99

Flexi Transport Module Parameters CCFA Parameters


10.3 vccBundleEnabled (VCC Bundle Enabling Flag)

Parameter name VCC Bundle Enabling Flag

Abbreviated name vccBundleEnabled

3GPP name -

Managed Object CCFA

Multiplicity 1

Description This parameter enables VCC bundling for collecting extra bandwidth unused by neighbour VCCs.


Step -

Units -


– false => 0 – true => 1



Related functions -




Related options -

Feature dependencies – CR 1406 Improvements for VCC bundle


References -

Table 46 vccBundleEnabled (VCC Bundle Enabling Flag)

100 DN70577885



CERTH Parameters

11 CERTH Parameters

11.1 btsCertificateUpdateTime (BTS certificate update time)

11.2 caCertificateUpdateTime (CA certificate update time)

Parameter name BTS certificate update time

Abbreviated name btsCertificateUpdateTime

3GPP name -

Managed Object CERTH

Multiplicity 1

Description This parameter specifies how many days in advance to the BTS certificate expiry date, the FTM shall execute a CMP update.

Range 1... 4999

Step 1

Units days



Default value 30

Default value notes Default value is 1 month.

Related functions -




Related options – RAN1899 Factory and Customer PKI



References -

Table 47 btsCertificateUpdateTime (BTS certificate update time)

Parameter name CA certificate update time

Abbreviated name caCertificateUpdateTime

3GPP name -

Table 48 caCertificateUpdateTime (CA certificate update time)

DN70577885 101

Flexi Transport Module Parameters CERTH Parameters


11.3 caSubjectName (CMP server subject name)


Multiplicity 1

Description This parameter specifies how many days in advance to the CA or Trust Anchor certificate expiry date, the FTM shall execute a CMP update.

Range 1... 4999

Step 1

Units days



Default value 180

Default value notes Default value is 6 months.

Related functions -




Related options – RAN1899 Factory and Customer PKI



References -

Table 48 caCertificateUpdateTime (CA certificate update time) (Cont.)

Parameter name CMP server subject name

Abbreviated name caSubjectName

3GPP name -


Multiplicity 1

Description This parameter identifies the CMP server by its subject name. It may either be detected by DHCP upon autoconnection or configured by the manage-ment system.

Range 0...128

Step -

Table 49 caSubjectName (CMP server subject name)

102 DN70577885



CERTH Parameters

11.4 certhId (Certification Handler Identifier)

Units characters



Default value -

Default value notes Length value 0 means CA subject name is not con-figured

Related functions -




Related options – RAN963 Network Element Certificate Manage-ment



References -

Table 49 caSubjectName (CMP server subject name) (Cont.)

Parameter name Certification Handler Identifier

Abbreviated name certhId

3GPP name -


Multiplicity 1

Description This parameter identifies the certificate handler configuration. The value is always 1.

Range 1... 1

Step 1

Units -



Default value -


Related functions -


Table 50 certhId (Certification Handler Identifier)

DN70577885 103



11.5 cmpServerIpAddress (CMP Server IP Address)






References -

Table 50 certhId (Certification Handler Identifier) (Cont.)

Parameter name CMP Server IP Address

Abbreviated name cmpServerIpAddress

3GPP name -


Multiplicity 1

Description This is the IP address of the Certificate Manage-ment Protocol server. To be entered in dotted decimal format.

Range 7...15

Step -

Units characters



Default value -


Related functions -






Table 51 cmpServerIpAddress (CMP Server IP Address)

104 DN70577885



CERTH Parameters

11.6 cmpServerPort (CMP Server Port)


References -

Table 51 cmpServerIpAddress (CMP Server IP Address) (Cont.)

Parameter name CMP Server Port

Abbreviated name cmpServerPort

3GPP name -


Multiplicity 1

Description This is the port number to be used for addressing the Certificate Management Protocol server.

Range 1... 65535

Step 1

Units -



Default value 1024


Related functions -







References -

Table 52 cmpServerPort (CMP Server Port)

DN70577885 105



11.7 crServerIpAddress (CR Server IP Address)

11.8 crServerPort (CR Server Port)

Parameter name CR Server IP Address

Abbreviated name crServerIpAddress

3GPP name -


Multiplicity 1

Description This is the IP Address of the CR Server in dotted decimal format.

Range 7...15

Step -

Units characters



Default value -


Related functions -







References -

Table 53 crServerIpAddress (CR Server IP Address)

Parameter name CR Server Port

Abbreviated name crServerPort

3GPP name -


Multiplicity 1

Table 54 crServerPort (CR Server Port)

106 DN70577885



CERTH Parameters

11.9 crlUpdatePeriod (Certificate Revocation List update period)

Description This is the port number to be used for addressing the CR server in certificate management.

Range 1... 65535

Step 1

Units -



Default value -


Related functions -







References -

Table 54 crServerPort (CR Server Port) (Cont.)

Parameter name Certificate Revocation List update period

Abbreviated name crlUpdatePeriod

3GPP name -


Multiplicity 1

Description This parameter specifies the regular period for exe-cuting a periodical update of the Certificate Revo-cation List. In hours. Value 0 means "no periodical update".

Range 0... 8760

Step 1

Units -

Table 55 crlUpdatePeriod (Certificate Revocation List update period)

DN70577885 107





Default value 0

Default value notes No periodical update.

Related functions -




Related options -

Feature dependencies – CN4065


References -

Table 55 crlUpdatePeriod (Certificate Revocation List update period) (Cont.)

108 DN70577885



CESIF Parameters

12 CESIF Parameters

12.1 cesMinUDPPort (CES over PSN source port value range)

Parameter name CES over PSN source port value range

Abbreviated name cesMinUDPPort

3GPP name -

Managed Object CESIF

Multiplicity 1

Description This parameter defines the range of the source port numbers that shall be used for CES over PSN. The parameter defines the lower value of that range. This port and the subsequent ports are used for the CES over PSN pseudowires.

Also a remote UDP port number is defined for each CES over PSN pseudowire. Local and remote port may but don't have to be different.

It shall be ensured that CES over PSN ports are not configured for other purposes. i.e. other pseudowires or 3G traffic types.

Range 49152... 65532

Step 1

Units -



Default value -


Related functions -




Related options – RAN1707 Flexi WCDMA Integrated CESoPSN



References -

Table 56 cesMinUDPPort (CES over PSN source port value range)

DN70577885 109

Flexi Transport Module Parameters CESIF Parameters


12.2 cesifId (CES over PSN interface identifier)

Parameter name CES over PSN interface identifier

Abbreviated name cesifId

3GPP name -

Managed Object CESIF

Multiplicity 1

Description This parameter identified the CES over PSN inter-face. Its value is always 1.

Range 1... 1

Step 1

Units -



Default value -


Related functions -







References -

Table 57 cesifId (CES over PSN interface identifier)

110 DN70577885



CESPW Parameters

13 CESPW Parameters

13.1 administrativeState (Administrative state)

Parameter name Administrative state

Abbreviated name administrativeState

3GPP name -

Managed Object CESPW

Multiplicity 1

Description This parameter is used to lock and unlock the CES over PSN pseudowire.

Locking the pseudowire switches the CES function-ality off. Also all CES over PSN related alarms are suppressed.

Range locked (0), unlocked (1)

Step -

Units -


gui ==> internal

locked ==> 0

unlocked ==> 1

Default value locked (0)


Related functions -



administrativeState of P3SL - The features CES over PSN and Single Link PPP cannot be operated together.

administrativeState of P3ML - The features CES over PSN and Multi Link PPP cannot be operated together.




Table 58 administrativeState (Administrative state)

DN70577885 111

Flexi Transport Module Parameters CESPW Parameters


13.2 cesPWid (CES over PSN Pseudowire Identifier)


References -

Table 58 administrativeState (Administrative state) (Cont.)

Parameter name CES over PSN Pseudowire Identifier

Abbreviated name cesPWid

3GPP name -


Multiplicity 1

Description This parameter identifies the CES over PSN pseudowire.

The format of the parameter is slot#-if#

where slot# is the slot of the unit where the interface resides and if# is the interface number of the corre-sponding PDH interface on this unit.

In this release slot is always 1.

The value range of the if# part of the parameter depends on the hardware:

FIIB, FILB, FTIB, FTLB: 1..4

FTIF, FIIF: 1..8

FTFB: 1..16

Range 3...4

Step -

Units characters



Default value -


Related functions -




Table 59 cesPWid (CES over PSN Pseudowire Identifier)

112 DN70577885



CESPW Parameters

13.3 dscp (DSCP value)




References -

Table 59 cesPWid (CES over PSN Pseudowire Identifier) (Cont.)

Parameter name DSCP value

Abbreviated name dscp

3GPP name -


Multiplicity 1

Description This is the Diff Serve Code Point value that shall be inserted into the traffic that is running over this CES over PSN pseudowire.

Range 0... 63

Step 1

Units -



Default value 46

Default value notes This corresponds to the Per Hop Behaviour for Expedited Forwarding (EF).

Related functions -







Table 60 dscp (DSCP value)

DN70577885 113



13.4 framesNumber (Number of frames per CESoPSN packet)

References -

Table 60 dscp (DSCP value) (Cont.)

Parameter name Number of frames per CESoPSN packet

Abbreviated name framesNumber

3GPP name -


Multiplicity 1

Description This parameter holds the number of frames per CES over PSN packet.

Note: the number of frames per packet multiplied by the number of PDH timeslots (parameter payload-Timeslots) shall be between 40 and 1536. Other-wise the resulting CESoPSN packet size is violating the allowed ethernet packet size and the CES con-nection cannot be established.

Range 2... 32

Step 1

Units -



Default value 8


Related functions -


Related parameters payloadTimeslots of CESPW - The number of frames per packet multiplied by the number of PDH timeslots (parameter payload-Timeslots) shall be between 40 and 1536. Other-wise the resulting CESoPSN packet size is violating the allowed ethernet packet size and the CES con-nection cannot be established.




Table 61 framesNumber (Number of frames per CESoPSN packet)

114 DN70577885



CESPW Parameters

13.5 jitterBufferSize (Jitter Buffer Size)



References -

Table 61 framesNumber (Number of frames per CESoPSN packet) (Cont.)

Parameter name Jitter Buffer Size

Abbreviated name jitterBufferSize

3GPP name -


Multiplicity 1

Description This parameter holds the jitter buffer size to be used by the LLP to equalize the packet delay variation on the network for this pseudowire.

Unit: the value of the parameter is used as +/- x mil-liseconds, meaning that packets x ms too late or x ms too early still fit into the jitter buffer.

Value range is +/- 125 microseconds to +/- 64 milli-seconds.

A higher value allows equalizing more jitter but increases the end-to-end delay.

Range 500... 64000

Step 1

Units microseconds



Default value 8000


Related functions -





Table 62 jitterBufferSize (Jitter Buffer Size)

DN70577885 115



13.6 payloadTimeslots (Payload timeslots of TDM frame)



References -

Table 62 jitterBufferSize (Jitter Buffer Size) (Cont.)

Parameter name Payload timeslots of TDM frame

Abbreviated name payloadTimeslots

3GPP name -


Multiplicity 31

Description This parameter defines which timeslots from each TDM frame are used to form the packet payload for CES over PSN over this pseudowire. The set of configured timeslots may be an arbitrary one. It does not have to be contiguous.

Note that timeslot 0 is never transmitted.

Range: [1...31] for E1 and [1...24] for T1/JT1.

Note: the number of timeslots multiplied by the number of frames per packet (parameter fra-mesNumber) shall be between 40 and 1536. Other-wise the resulting CESoPSN packet size is violating the allowed ethernet packet size and the CES con-nection cannot be established.

Range TS1 (1), TS2 (2), TS3 (3), TS4 (4), TS5 (5), TS6 (6), TS7 (7), TS8 (8), TS9 (9), TS10 (10), TS11 (11), TS12 (12), TS13 (13), TS14 (14), TS15 (15), TS16 (16), TS17 (17), TS18 (18), TS19 (19), TS20 (20), TS21 (21), TS22 (22), TS23 (23), TS24 (24), TS25 (25), TS26 (26), TS27 (27), TS28 (28), TS29 (29), TS30 (30), TS31 (31)

Step -

Units -

Table 63 payloadTimeslots (Payload timeslots of TDM frame)

116 DN70577885



CESPW Parameters


gui ==> internal

TS1 ==> 1

TS2 ==> 2

TS3 ==> 3

TS4 ==> 4

TS5 ==> 5

TS6 ==> 6

TS7 ==> 7

TS8 ==> 8

TS9 ==> 9

TS10 ==> 10

TS11 ==> 11

TS12 ==> 12

TS13 ==> 13

TS14 ==> 14

TS15 ==> 15

TS16 ==> 16

TS17 ==> 17

TS18 ==> 18

TS19 ==> 19

TS20 ==> 20

TS21 ==> 21

TS22 ==> 22

TS23 ==> 23

TS24 ==> 24

TS25 ==> 25

TS26 ==> 26

TS27 ==> 27

TS28 ==> 28

TS29 ==> 29

TS30 ==> 30

TS31 ==> 31

Default value -


Related functions -


Table 63 payloadTimeslots (Payload timeslots of TDM frame) (Cont.)

DN70577885 117



13.7 remoteUDPPort (Remote UDP port number for CES over PSN)

Related parameters framesNumber of CESPW - The number of timeslots multiplied by the number of frames per packet (parameter framesNumber) shall be between 40 and 1536. Otherwise the resulting CESoPSN packet size is violating the allowed ethernet packet size and the CES connection cannot be established.






References -

Table 63 payloadTimeslots (Payload timeslots of TDM frame) (Cont.)

Parameter name Remote UDP port number for CES over PSN

Abbreviated name remoteUDPPort

3GPP name -


Multiplicity 1

Description This is the number of the remote UDP port to be used for running traffic on the CES over PSN pseudowire. The remote port is used to identify packets belonging to this pseudowire.

Also a local UDP port number is defined for this CES pseudowire. Local and remote port may but don't have to be different.

It shall be ensured that both ports are not config-ured for other purposes. i.e. other pseudowires or 3G traffic types.

Range 49152... 65535

Step 1

Units -

Table 64 remoteUDPPort (Remote UDP port number for CES over PSN)

118 DN70577885



CESPW Parameters



Default value -


Related functions -







References -

Table 64 remoteUDPPort (Remote UDP port number for CES over PSN) (Cont.)

DN70577885 119

Flexi Transport Module Parameters CESPWT Parameters


14 CESPWT Parameters

14.1 cesPWTid (CES over PSN pseudowire tunnel identifier)

14.2 destIpAddress (Destination IP address)

Parameter name CES over PSN pseudowire tunnel identifier

Abbreviated name cesPWTid

3GPP name -

Managed Object CESPWT

Multiplicity 1

Description This parameter identifies the CES over PSN pseudowire tunnel. Its value is always 1. Currently only 1 pseudowire tunnel can be configured for CES over PSN.

Range 1... 1

Step 1

Units -



Default value -


Related functions -







References -

Table 65 cesPWTid (CES over PSN pseudowire tunnel identifier)

Parameter name Destination IP address

Table 66 destIpAddress (Destination IP address)

120 DN70577885



CESPWT Parameters

Abbreviated name destIpAddress

3GPP name -

Managed Object CESPWT

Multiplicity 1

Description This is the destination IP address of the packets belonging to the CES over PSN pseudowire tunnel.

This is an IPv4 IP address in dotted decimal format.

Range 7...15

Step -

Units characters



Default value -


Related functions -







References -

Table 66 destIpAddress (Destination IP address) (Cont.)

DN70577885 121

Flexi Transport Module Parameters ETHLK Parameters


15 ETHLK Parameters

15.1 acceptableFrameTypes (Switch Port Acceptable Frame Types)

Parameter name Switch Port Acceptable Frame Types

Abbreviated name acceptableFrameTypes

3GPP name -

Managed Object ETHLK

Multiplicity 1

Description If discardUntagged has value true, any untagged ingress frame is discarded.

If discardUntagged has value false, any untagged ingress frame is assigned internally the default VLAN ID, i.e. the value of parameter defaultVlanId. If the interface on which the packet is to be trans-mitted contains the same VLAN id in its list of con-figured VLAN identifiers (parameter ETHLK - l2VlanIdList), the packet will indeed be transmitted via this interface, else it will be discarded.

Range ADMIT_ALL (0), ADMIT_TAGGED (1)

Step -

Units -


gui ==> internal

ADMIT_ALL ==> 0

ADMIT_TAGGED ==> 1

Default value ADMIT_ALL (0)


Related functions -




Related options – RAN1769 Ethernet Switching


Table 67 acceptableFrameTypes (Switch Port Acceptable Frame Types)

122 DN70577885



ETHLK Parameters

15.2 administrativeState (Administrative State)


References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement

Table 67 acceptableFrameTypes (Switch Port Acceptable Frame Types) (Cont.)

Parameter name Administrative State


3GPP name -


Multiplicity 1

Description This parameter is used to lock and unlock the inter-face.

Locking the interface deactivates it and all alarms and any traffic over the interface is suppressed.


Step -

Units -


gui ==> internal

locked ==> 0

unlocked ==> 1



Related functions -




Related options -



References -

Table 68 administrativeState (Administrative State)

DN70577885 123



15.3 ethLinkId (Ethernet Link Identifier)

Parameter name Ethernet Link Identifier

Abbreviated name ethLinkId

3GPP name -


Multiplicity 1

Table 69 ethLinkId (Ethernet Link Identifier)

124 DN70577885



ETHLK Parameters

Description This parameter identifies the BTS transport Ethernet interface.

Format: "slot#-if#"

where

slot# = slot number of the unit containing the Ethernet interfaces, and

if# = the interface number of the physical interface on the unit

and

for FTIB/FTLB,

slot#: 1 : This is always 1, since there is only 1 slot.

if#: 1..3

for FTFB,

slot#: 1 : This is always 1, since there is only 1 slot.

if#: 1..4

Ports 1 and 2 are reserved for the external Gigabit Ethernet links. Ports 3 and 4 are reserved for the Ethernet links towards the FlexBus.

for Flexi BTS Release 3 Outdoor System Module (FSM),

slot#: 0 : This is always 0, since Transport is integrated into common system module.

if#: 1..2 : Value range is 1..2 for EIF1..EIF2 on this unit

Additionally, EIF2 can be configured as an RP3-01 port.

for Flexi BTS Release 3 Indoor System Module (FSI),

slot#: 0 : This is always 0, since Transport is integrated into common system module.

if#: 1..5 : Value range is 1..5 for EIF1..EIF5.

Usage of EIF1 and EIF3 is mutually exclusive. Similarly for EIF2 and EIF4. Additionally, EIF5 can be configured as an RP3-01 port.

for FTIF (optional outdoor external Transport module),

slot#: 1 : The slot number is '1', since this is an additional unit

if#: 1..4 : Value range is 1..4 for EIF1..EIF4 on this unit

Usage of EIF1 and EIF3 is mutually exclusive. Similarly for EIF2 and EIF4. Usage of EIF1/EIF3 on this unit and EIF2 on FSM is mutually exclusive.

for FIIF (optional indoor external Transport module),

slot#: 1 : The slot number is '1', since this is an additional unit

DN70577885 125



15.4 flushFdbOnLos (Flush fdb on LOS mode)

Range 3

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 69 ethLinkId (Ethernet Link Identifier) (Cont.)

Parameter name Flush fdb on LOS mode

Abbreviated name flushFdbOnLos

3GPP name -


Multiplicity 1

Description This parameter is available in WN7.0 2.0 release.

This parameter is true then dynamic MAC address entries of Forwarding Database (fdb) should be flushed when an Ethernet Layer Loss of Signal (LOS) is detected on one of its external switch-ports.


Step -

Units -


– false => 0 – true => 1

Table 70 flushFdbOnLos (Flush fdb on LOS mode)

126 DN70577885



ETHLK Parameters

15.5 l2BurstSize (Switch Port egress Shaper Burst Size)



Related functions -




Related options -


Interfaces – FTM <-> EM– FTM <-> RAC– RAC <-> RACApp

References -

Table 70 flushFdbOnLos (Flush fdb on LOS mode) (Cont.)

Parameter name Switch Port egress Shaper Burst Size

Abbreviated name l2BurstSize

3GPP name -


Multiplicity 1

Description This parameter specifies the maximum burst size that can be transmitted in a single burst in egress direction on this Ethernet interface of layer 2 switch. The burst size is actually calculated by < l2ShaperRate x l2BurstSize x 1sec >. Example: l2ShaperRate =100 Mb/s and l2BurstSize=1% results in a burst size of 1 Mbit = 125 Kbyte.

This parameter is valid only for FTLB.

Range 0... 60

Step 1

Units -



Default value 0

Default value notes By default no bursts are allowed.

Related functions -

Table 71 l2BurstSize (Switch Port egress Shaper Burst Size)

DN70577885 127



15.6 l2IngressRate (Switch Port ingress RateLimiter Rate )







References -

Table 71 l2BurstSize (Switch Port egress Shaper Burst Size) (Cont.)

Parameter name Switch Port ingress RateLimiter Rate

Abbreviated name l2IngressRate

3GPP name -


Multiplicity 1

Description This parameter specifies the rate for limiting ingress traffic at the ethernet link interface when it partici-pates in the QOS aware layer 2 switch. Parameter value unit = MBit/s.

Table 72 l2IngressRate (Switch Port ingress RateLimiter Rate )

128 DN70577885



ETHLK Parameters

Range RT_LINE_RATE (0), RT_1 (1), RT_2 (2), RT_3 (3), RT_4 (4), RT_5 (5), RT_6 (6), RT_7 (7), RT_8 (8), RT_9 (9), RT_10 (10), RT_11 (11), RT_12 (12), RT_13 (13), RT_15 (15), RT_16 (16), RT_17 (17), RT_18 (18), RT_20 (20), RT_22 (22), RT_23 (23), RT_24 (24), RT_25 (25), RT_26 (26), RT_28 (28), RT_29 (29), RT_30 (30), RT_32 (32), RT_35 (35), RT_36 (36), RT_40 (40), RT_41 (41), RT_42 (42), RT_45 (45), RT_48 (48), RT_50 (50), RT_55 (55), RT_58 (58), RT_60 (60), RT_63 (63), RT_65 (65), RT_70 (70), RT_72 (72), RT_75 (75), RT_80 (80), RT_84 (84), RT_85 (85), RT_90 (90), RT_95 (95), RT_96 (96), RT_100 (100), RT_125 (125), RT_143 (143), RT_150 (150), RT_200 (200), RT_250 (250), RT_256 (256), RT_286 (286), RT_300 (300), RT_350 (350), RT_400 (400), RT_450 (450), RT_500 (500), RT_550 (550), RT_600 (600), RT_650 (650), RT_700 (700), RT_750 (750), RT_800 (800), RT_850 (850), RT_900 (900), RT_950 (950), RT_1000 (1000)

Step -

Units -

Table 72 l2IngressRate (Switch Port ingress RateLimiter Rate ) (Cont.)

DN70577885 129




gui ==> internal

RT_LINE_RATE ==> 0

RT_1 ==> 1

RT_2 ==> 2

RT_3 ==> 3

RT_4 ==> 4

RT_5 ==> 5

RT_6 ==> 6

RT_7 ==> 7

RT_8 ==> 8

RT_9 ==> 9

RT_10 ==> 10

RT_11 ==> 11

RT_12 ==> 12

RT_13 ==> 13

RT_15 ==> 15

RT_16 ==> 16

RT_17 ==> 17

RT_18 ==> 18

RT_20 ==> 20

RT_22 ==> 22

RT_23 ==> 23

RT_24 ==> 24

RT_25 ==> 25

RT_26 ==> 26

RT_28 ==> 28

RT_29 ==> 29

RT_30 ==> 30

RT_32 ==> 32

RT_35 ==> 35

RT_36 ==> 36

RT_40 ==> 40

RT_41 ==> 41

RT_42 ==> 42

RT_45 ==> 45

RT_48 ==> 48

RT_50 ==> 50

RT_55 ==> 55

RT_58 ==> 58

RT_60 ==> 60

RT_63 ==> 63

RT_65 ==> 65

RT_70 ==> 70

RT 72 ==> 72

130 DN70577885



ETHLK Parameters

15.7 l2ShaperRate (Switch Port egress Shaper Rate)

Default value RT_LINE_RATE (0)

Default value notes Use the configured line rate of the interface from the operator. This is defined in parameter ETHLK - speedAndDuplex. If the line rate is not configured forcibly by the operator, it is autodetected by the BTS.

Related functions -







References -

Table 72 l2IngressRate (Switch Port ingress RateLimiter Rate ) (Cont.)

Parameter name Switch Port egress Shaper Rate

Abbreviated name l2ShaperRate

3GPP name -


Multiplicity 1

Description This parameter specifies the shaping rate of the ethernet link interface when participating in the QOS aware layer 2 switch.

The actual shaper rate is derived from the config-ured shaper rate by internal calculation.

Table 73 l2ShaperRate (Switch Port egress Shaper Rate)

DN70577885 131



Range RT_LINE_RATE (0), RT_1 (1), RT_2 (2), RT_3 (3), RT_4 (4), RT_5 (5), RT_6 (6), RT_7 (7), RT_8 (8), RT_9 (9), RT_10 (10), RT_11 (11), RT_12 (12), RT_13 (13), RT_15 (15), RT_16 (16), RT_17 (17), RT_18 (18), RT_20 (20), RT_22 (22), RT_23 (23), RT_24 (24), RT_25 (25), RT_26 (26), RT_28 (28), RT_29 (29), RT_30 (30), RT_32 (32), RT_35 (35), RT_36 (36), RT_40 (40), RT_41 (41), RT_42 (42), RT_45 (45), RT_48 (48), RT_50 (50), RT_55 (55), RT_58 (58), RT_60 (60), RT_63 (63), RT_65 (65), RT_70 (70), RT_72 (72), RT_75 (75), RT_80 (80), RT_84 (84), RT_85 (85), RT_90 (90), RT_95 (95), RT_96 (96), RT_100 (100), RT_125 (125), RT_143 (143), RT_150 (150), RT_200 (200), RT_250 (250), RT_256 (256), RT_286 (286), RT_300 (300), RT_350 (350), RT_400 (400), RT_450 (450), RT_500 (500), RT_550 (550), RT_600 (600), RT_650 (650), RT_700 (700), RT_750 (750), RT_800 (800), RT_850 (850), RT_900 (900), RT_950 (950), RT_1000 (1000)

Step -

Units -

Table 73 l2ShaperRate (Switch Port egress Shaper Rate) (Cont.)

132 DN70577885



ETHLK Parameters


gui ==> internal

RT_LINE_RATE ==> 0

RT_1 ==> 1

RT_2 ==> 2

RT_3 ==> 3

RT_4 ==> 4

RT_5 ==> 5

RT_6 ==> 6

RT_7 ==> 7

RT_8 ==> 8

RT_9 ==> 9

RT_10 ==> 10

RT_11 ==> 11

RT_12 ==> 12

RT_13 ==> 13

RT_15 ==> 15

RT_16 ==> 16

RT_17 ==> 17

RT_18 ==> 18

RT_20 ==> 20

RT_22 ==> 22

RT_23 ==> 23

RT_24 ==> 24

RT_25 ==> 25

RT_26 ==> 26

RT_28 ==> 28

RT_29 ==> 29

RT_30 ==> 30

RT_32 ==> 32

RT_35 ==> 35

RT_36 ==> 36

RT_40 ==> 40

RT_41 ==> 41

RT_42 ==> 42

RT_45 ==> 45

RT_48 ==> 48

RT_50 ==> 50

RT_55 ==> 55

RT_58 ==> 58

RT_60 ==> 60

RT_63 ==> 63

RT_65 ==> 65

RT_70 ==> 70

RT 72 ==> 72

DN70577885 133



15.8 l2VlanIdList (Switch Port VLAN Member List)

Default value RT_LINE_RATE (0)

Default value notes Use the configured line rate of the interface from the operator. This is defined in parameter ETHLK - speedAndDuplex. If the line rate is not configured forcibly by the operator, it is autodetected by the BTS.

Related functions -







References -

Table 73 l2ShaperRate (Switch Port egress Shaper Rate) (Cont.)

Parameter name Switch Port VLAN Member List

Abbreviated name l2VlanIdList

3GPP name -


Multiplicity 16

Description This parameter specifies the VLANs that are sup-ported over this ethernet interface when it partici-pates in the QOS aware layer 2 switch. The parameter is a list of up to 16 entries where each entry represents either a single VLAN identifier or a range of VLAN identifiers. The VLAN identifiers of the various entries should not but may overlap each other. The BTS internally will use a cleaned list on non-overlapping identifiers. The value of vlanIdList is however not changed by the BTS.

The default value of the parameter is the empty list.


-

Table 74 l2VlanIdList (Switch Port VLAN Member List)

134 DN70577885



ETHLK Parameters

15.9 highValue (Switch Port VLAN Member Range High Value)

Default value -


Related functions -

Child parameters – highValue– lowValue







References -

Table 74 l2VlanIdList (Switch Port VLAN Member List) (Cont.)

Parameter name Switch Port VLAN Member Range High Value

Abbreviated name highValue

3GPP name -

Managed Object -

Multiplicity 1

Description This parameter specifies the upper value of a range of VLAN identifiers.

Range -1... 4094

Step 1

Units -



Default value -1


Related functions -


Table 75 highValue (Switch Port VLAN Member Range High Value)

DN70577885 135



15.10 lowValue (Switch Port VLAN Member Range Low Value)






References -

Table 75 highValue (Switch Port VLAN Member Range High Value) (Cont.)

Parameter name Switch Port VLAN Member Range Low Value

Abbreviated name lowValue

3GPP name -

Managed Object -

Multiplicity 1

Description This parameter specifies either a single VLAN iden-tifier or the lower value of a range of VLAN identifi-ers.

Range 1... 4094

Step 1

Units -



Default value 1

Default value notes Default value means "untagged".

Related functions -






Table 76 lowValue (Switch Port VLAN Member Range Low Value)

136 DN70577885



ETHLK Parameters

15.11 linkOAMEnabled (Link OAM enabling flag)


References -

Table 76 lowValue (Switch Port VLAN Member Range Low Value) (Cont.)

Parameter name Link OAM enabling flag

Abbreviated name linkOAMEnabled

3GPP name -


Multiplicity 1

Description Enables the Link OAM functionality for this ethernet link. In consequence:

- the values of all statistics counters of the Link OAM feature for this interface are set to 0

- the Link OAM alarms for this interface are cleared

- the Link OAM discovery process is started, either in active or in passive mode linkOAMEnabled cannot be set to FB bit pipe interfaces


Step -

Units -


– false => 0 – true => 1


Default value notes Link OAM is not enabled for the interface.

Related functions -



linkOAMProfile of ETHLK - The value of linkOAMEnabled shall only be set to true, if the value of linkOAMProfile is not the empty string but references an existing instance of object class OAMPRF.


Table 77 linkOAMEnabled (Link OAM enabling flag)

DN70577885 137



15.12 linkOAMProfile (Link OAM profile reference)

Related options -



References -

Table 77 linkOAMEnabled (Link OAM enabling flag) (Cont.)

Parameter name Link OAM profile reference

Abbreviated name linkOAMProfile

3GPP name -


Multiplicity 1

Description A reference to a Link OAM profile. This is a distin-guished name referencing an instance of class OAMPRF.

Range 0...40

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 78 linkOAMProfile (Link OAM profile reference)

138 DN70577885



ETHLK Parameters

15.13 macAddr (MAC address)

15.14 portDefaultPriority (Switch Port Default VLAN Priority)

Parameter name MAC address

Abbreviated name macAddr

3GPP name -


Multiplicity 1

Description This parameter shows the MAC address of the ethernet interface.

Range 17

Step -

Units characters



Default value -


Related functions -




Related options -


Interfaces – FTM -> EM– FTM -> RAC– RAC <-> RACApp

References -

Table 79 macAddr (MAC address)

Parameter name Switch Port Default VLAN Priority

Abbreviated name portDefaultPriority

3GPP name -


Multiplicity 1

Table 80 portDefaultPriority (Switch Port Default VLAN Priority)

DN70577885 139



15.15 portDefaultVlanId (Switch Port Default VLAN Identifier)

Description Default VLAN priority for untagged frames.

Every untagged ingress Ethernet frame at this inter-face gets assigned this Port Default Priority. If QoS classification mode is configured to VLAN-PCP, this priority is used for enqueing decision of the frame. If the frame egresses the switch tagged, this priority shall be used in the VLAN tag header.

Range 0... 7

Step 1

Units -



Default value 0


Related functions -



enableLayer2Switching of L2SWI - VLAN aware switching mode should be enabled (enableLayer2Switching="true")






Table 80 portDefaultPriority (Switch Port Default VLAN Priority) (Cont.)

Parameter name Switch Port Default VLAN Identifier

Abbreviated name portDefaultVlanId

3GPP name -


Table 81 portDefaultVlanId (Switch Port Default VLAN Identifier)

140 DN70577885



ETHLK Parameters

15.16 speedAndDuplex (Speed and Duplex flag)

Multiplicity 1

Description This parameter specifies the VLAN identifier that is inserted internally by the FTM into an untagged ingress frame that enters the layer 2 switch via this Ethernet interface - if parameter discardUntagged has value false for the Ethernet interface.

In order that the frame will be transmitted via the same or another Ethernet interface, after layer 2 switching has been performed, the same VLAN id must be configured in the VLAN identifier list of that Ethernet interface (see parameter l2VlanIdList). Else the frame will be discarded.

Range 1... 4094

Step 1

Units -



Default value 1

Default value notes Default VLAN id = 1.

Related functions -



enableLayer2Switching of L2SWI - VLAN aware switching mode should be enabled (enableLayer2Switching="true")






Table 81 portDefaultVlanId (Switch Port Default VLAN Identifier) (Cont.)

Parameter name Speed and Duplex flag

Table 82 speedAndDuplex (Speed and Duplex flag)

DN70577885 141



Abbreviated name speedAndDuplex

3GPP name -


Multiplicity 1

Description This parameter specificies if link characteristics are autonegotiated or not.

If not, the attribute contains the capacity and the duplex mode to be set forcibly. Note that 1000 MBit is available only on Gigabit Ethernet interfaces (GE).

This parameter is not applied for the FlexBus inter-faces of the FTFB hardware unit (interfaces 3 and 4 of the FTFB unit). For these interfaces the capacity and traffic mode is not configurable by the manage-ment system.

Range AUTODETECT (0), 1000MBIT_FULL (1), 100MBIT_FULL (2), 10MBIT_FULL (3)

Step -

Units -


gui ==> internal

AUTODETECT ==> 0

1000MBIT_FULL ==> 1

100MBIT_FULL ==> 2

10MBIT_FULL ==> 3

Default value AUTODETECT (0)


Related functions -




Related options -



References -

Table 82 speedAndDuplex (Speed and Duplex flag) (Cont.)

142 DN70577885



ETHLK Parameters

15.17 synchEMode (Synchronous ethernet mode)

Parameter name Synchronous ethernet mode

Abbreviated name synchEMode

3GPP name -


Multiplicity 1

Description This parameter specifies if the FTM shall act as synchronous ethernet clock slave or master on this ethernet interface. The mode may also be autone-giotiated. An alarm shall be raised in case of a mode mismatch with the peer. The parameter is only relevant in case the synchronous ethernet regenerator function is switched on.

Range SEM_AUTO (0), SEM_SLAVE (1), SEM_MASTER (2)

Step -

Units -


gui ==> internal

SEM_AUTO ==> 0

SEM_SLAVE ==> 1

SEM_MASTER ==> 2

Default value SEM_AUTO (0)

Default value notes By default the mode is autonegotiated.

Related functions -


Related parameters synchERegenOn of STPG - Parameter synchEMode is only relevant in case parameter synchERegenOn has value true.


Related options – RAN2071 Synchronous Ethernet Generation



References -

Table 83 synchEMode (Synchronous ethernet mode)

DN70577885 143

Flexi Transport Module Parameters FRLI Parameters


16 FRLI Parameters

16.1 afrLinkInterfaceId (Fractional Interface Identifier)

Parameter name Fractional Interface Identifier

Abbreviated name afrLinkInterfaceId

3GPP name -

Managed Object FRLI

Multiplicity 1

Description This parameter identifies the fractional interface of a unit.


- unit location (slot#)

- interface location (if#)

Format: slot#-if#

Ranges:

slot#: 1 (always)

if#:

FIIB, FILB, FTIB, FTIA, FTLB: 1..4

FTPB: 1..8

Fractional is only available on units FTPB, FTIA, FTIB and FTLB. Note that only 1 interface shall be used for fractional at any given time. FRLI is sup-ported only for JT1 capable unit when PDH IF type is JT1.

Range 3

Step -

Units characters



Default value -


Related functions -




Related options -

Table 84 afrLinkInterfaceId (Fractional Interface Identifier)

144 DN70577885



FRLI Parameters

16.2 afrTimeSlotSequence (ATM over Fractional JT1 Time Slot Sequence)



References -

Table 84 afrLinkInterfaceId (Fractional Interface Identifier) (Cont.)

Parameter name ATM over Fractional JT1 Time Slot Sequence

Abbreviated name afrTimeSlotSequence

3GPP name -

Managed Object FRLI

Multiplicity 24

Description Specifies a list of consequtive timeslots that are to be used for an ATM interface, starting from timeslot 1. The maximum number of timeslots is 24.

At least two timeslots must be used.

Range TS1 (1), TS2 (2), TS3 (3), TS4 (4), TS5 (5), TS6 (6), TS7 (7), TS8 (8), TS9 (9), TS10 (10), TS11 (11), TS12 (12), TS13 (13), TS14 (14), TS15 (15), TS16 (16), TS17 (17), TS18 (18), TS19 (19), TS20 (20), TS21 (21), TS22 (22), TS23 (23), TS24 (24)

Step -

Units -

Table 85 afrTimeSlotSequence (ATM over Fractional JT1 Time Slot Sequence)

DN70577885 145




gui ==> internal

TS1 ==> 1

TS2 ==> 2

TS3 ==> 3

TS4 ==> 4

TS5 ==> 5

TS6 ==> 6

TS7 ==> 7

TS8 ==> 8

TS9 ==> 9

TS10 ==> 10

TS11 ==> 11

TS12 ==> 12

TS13 ==> 13

TS14 ==> 14

TS15 ==> 15

TS16 ==> 16

TS17 ==> 17

TS18 ==> 18

TS19 ==> 19

TS20 ==> 20

TS21 ==> 21

TS22 ==> 22

TS23 ==> 23

TS24 ==> 24

Default value -


Related functions -


Related parameters pdhLineType of PPTT - JT1: EXTENDED_MULTIFRAME

Parameter relationships The "timeSlotSequence" must be set only if pdhLineType is set to EXTENDED_MULTIFRAME.

Related options -

Feature dependencies – RAN1649 ATM over Fractional JT1


146 DN70577885



FRLI Parameters

16.3 interfaceNumber (Interface Identifier)


References -


Parameter name Interface Identifier


3GPP name -

Managed Object FRLI

Multiplicity 1

Description Defines the location of the PDH interface that is used for fractional mode. The value depends on the unit type.

FTIB, FTIA, FTLB: 1..4

FTPB: 1..8

Range 1... 8

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 86 interfaceNumber (Interface Identifier)

DN70577885 147






3GPP name -

Managed Object FRLI

Multiplicity 1

Description This parameter identifies the slot number of the unit of the PDH interface that is used for fractional mode. The value is always 1 (only 1 slot available in this release).

Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -



References -


148 DN70577885



FTM Parameters

17 FTM Parameters

17.1 adaptationVersionMajor (Adaptation Version Major)

17.2 ftmId (BTS Transport Identifier)

Parameter name Adaptation Version Major

Abbreviated name adaptationVersionMajor

3GPP name -

Managed Object FTM

Multiplicity 1

Description Adaptation Version (Major) of the Site Configura-tion File supported by FTM.

Range 1...9

Step -

Units characters



Default value WN7.0 for WN7.0 1.0;

WN7.0_2.0 for WN7.0 2.0


Related functions -




Related options -



References -

Table 88 adaptationVersionMajor (Adaptation Version Major)

Parameter name BTS Transport Identifier

Abbreviated name ftmId

3GPP name -

Table 89 ftmId (BTS Transport Identifier)

DN70577885 149

Flexi Transport Module Parameters FTM Parameters


17.3 locationName (Location Name)

Managed Object FTM

Multiplicity 1

Description This parameter identifies BTS transport.

The value is always 1.

Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 89 ftmId (BTS Transport Identifier) (Cont.)

Parameter name Location Name

Abbreviated name locationName

3GPP name -

Managed Object FTM

Multiplicity 1

Description Label that can be used to describe the geographical location of the network element.

Range 0...50

Step -

Units characters

Table 90 locationName (Location Name)

150 DN70577885



FTM Parameters

17.4 softwareReleaseVersion (Software Release Version)



Default value -


Related functions -




Related options -



References -

Table 90 locationName (Location Name) (Cont.)

Parameter name Software Release Version

Abbreviated name softwareReleaseVersion

3GPP name -

Managed Object FTM

Multiplicity 1

Description Identifies the SW Release Version of the Flexi-Transport Module. This value is set by the BTS.

Range 0...50

Step -

Units characters



Default value -


Related functions -




Table 91 softwareReleaseVersion (Software Release Version)

DN70577885 151

Flexi Transport Module Parameters FTM Parameters


17.5 systemTitle (System Title)

Related options -



References -

Table 91 softwareReleaseVersion (Software Release Version) (Cont.)

Parameter name System Title

Abbreviated name systemTitle

3GPP name -

Managed Object FTM

Multiplicity 1

Description Label that can be used to enter the name of the network element.

Range 0...80

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 92 systemTitle (System Title)

152 DN70577885



FTM Parameters

17.6 userLabel (User Label)

Parameter name User Label

Abbreviated name userLabel

3GPP name -

Managed Object FTM

Multiplicity 1

Description Label that can be used for a description of the BTS.

Range 0...128

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 93 userLabel (User Label)

DN70577885 153

Flexi Transport Module Parameters IAIF Parameters


18 IAIF Parameters





3GPP name -

Managed Object IAIF

Multiplicity 1


Range 32... 4095

Step 1

Units -



Default value -


Related functions -




Related options -



References -




3GPP name -

Managed Object IAIF

Multiplicity 1



154 DN70577885



IAIF Parameters

18.3 atmIfNetId (ATM IP Net Interface Identifier)

Range 0... 255

Step 1

Units -



Default value -


Related functions -




Related options -



References -


Parameter name ATM IP Net Interface Identifier

Abbreviated name atmIfNetId

3GPP name -

Managed Object IAIF

Multiplicity 1

Table 96 atmIfNetId (ATM IP Net Interface Identifier)

DN70577885 155



Description Identifies an ATM interface over an Ethernet Pseudowire.


- Unit number (unit#)

- Interface number(if#, imag# or pw#)



Format:



Range:

unit#: 1



pw#: 76



Range 9...10

Step -

Units characters



Default value -


Related functions -


Related parameters VCI of IAIF - The value of parameter VCI is contained in the value of parame-ter atmIfNetId.

VPI of IAIF - The value of parameter VPI is contained in the value of parame-ter atmIfNetId.

interfaceNumber of IAIF - The value of parameter interfaceNumber is contained in the value of parameter atmIfNetId.

unitNumber of IAIF - The value of parameter unitNumber is contained in the value of parameter atmIfNetId.


Table 96 atmIfNetId (ATM IP Net Interface Identifier) (Cont.)

156 DN70577885



IAIF Parameters

18.4 destIpAddr (Destination IP Address)

Related options -



References -

Table 96 atmIfNetId (ATM IP Net Interface Identifier) (Cont.)

Parameter name Destination IP Address

Abbreviated name destIpAddr

3GPP name -

Managed Object IAIF

Multiplicity 1

Description Specifies the far-end IP address of an ATM point-to-point connection (IPoA).

Range 7...15

Step -

Units characters



Default value -


Related functions -


Related parameters ftmIpAddr of IPNO

Parameter relationships The ftmIpAddr must be configured first.

Related options -



References -

Table 97 destIpAddr (Destination IP Address)

DN70577885 157






3GPP name -

Managed Object IAIF

Multiplicity 1

Description Defines the location on the unit of the physical inter-face that carries the signallink link.

The value depends on the unit type.


FTIA, FIIB, FTIB, FTJA, FILB, FTLB: 1..4

FTFA, FTHA: 1..16

For IMA, the parameter identifies the IMA group. Values are: 33..75.

For the ATM over Ethernet pseudowire the value is always: 76.

Range 1... 76

Step 1

Units -



Default value -


Related functions -




Related options -



References -


158 DN70577885



IAIF Parameters




3GPP name -

Managed Object IAIF

Multiplicity 1


Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -



References -


DN70577885 159

Flexi Transport Module Parameters IEIF Parameters


19 IEIF Parameters

19.1 cir (Committed information rate)

Parameter name Committed information rate

Abbreviated name cir

3GPP name -

Managed Object IEIF

Multiplicity 1

Description The Committed Information Rate ("CIR") shall define the average rate up to which traffic is deliv-ered by the plain Ethernet interface. It shall define the guaranteed transport capacity for the interface. The parameter is required for dynamic CAC.

The sum of CIR values of all configured IP inter-faces (IEIF / IVIF) and CIR of Ethernet Service OAM multiplied by 1.2 cannot exceed the available Transport Ethernet interface bandwidth (see IEIF/shapedBandwidth and IEIF/sirTotal ) - Cir of Service OAM is taken in count if there exists at least one OAMMEP in the system.

If there are several IP interfaces and shaping is PATH, Connection Admission Control is based on CIR parameter of the IP interface that user plane uses.

Range 0... 1000000

Step 100

Units kbps



Default value -


Related functions -


Table 100 cir (Committed information rate)

160 DN70577885



IEIF Parameters

19.2 confCost (OSPF configured interface cost)

Related parameters shapedBandwidth of IEIF - The sum of CIR values of all configured IP interfaces (IEIF / IVIF) and CIR of Ethernet Service OAM mul-tiplied by 1.2 cannot exceed the available Transport Ethernet interface bandwidth (see IEIF/shaped-Bandwidth and IEIF/sirTotal ) - Cir of Service OAM is taken in count if there exists at least one OAMMEP in the system.

transportMode of IPNO - The parameter cir is only relevant in transport modes Dual Iub and IubIP.

localIpAddr of IEIF - The parameter cir is only relevant in case the interface is in use, i.e. in case the localIpAddr is different from 0.0.0.0.

sirTotal of IEIF - The sum of CIR values of all configured IP interfaces (IEIF / IVIF) and CIR of Ethernet Service OAM multiplied by 1.2 cannot exceed the available Transport Ethernet interface bandwidth (see IEIF/shapedBandwidth and IEIF/sirTotal ) - Cir of Service OAM is taken in count if there exists at least one OAMMEP in the system.


Related options – RAN1709 VLAN Traffic Differentiation



References -

Table 100 cir (Committed information rate) (Cont.)

Parameter name OSPF configured interface cost

Abbreviated name confCost

3GPP name -

Managed Object IEIF

Multiplicity 1

Table 101 confCost (OSPF configured interface cost)

DN70577885 161



19.3 helloInterval (OSPF keepalive message transmission interval)

Description This parameter specifies the cost used by the inter-face as defined by the operator. Value 0 means "not specified": If OSPF is enabled the cost calculated by the OSPF router shall be used instead.

Range 0... 65535

Step 1

Units -



Default value 0

Default value notes Default means: "not specified by the operator, use OSPF router calculated cost instead".

Related functions -




Related options – RAN1879 Dynamic routing by OSPF



References -

Table 101 confCost (OSPF configured interface cost) (Cont.)

Parameter name OSPF keepalive message transmission interval

Abbreviated name helloInterval

3GPP name -

Managed Object IEIF

Multiplicity 1

Description This parameter specifies the interval for transmit-ting keepalive ("Hello") messages.

Range 1... 65535

Step 1

Table 102 helloInterval (OSPF keepalive message transmission interval)

162 DN70577885



IEIF Parameters

19.4 ieifId (Identifier of the plain Ethernet interface)

Units -



Default value 1


Related functions -



routerDeadInterval of IEIF - Router dead interval should be greater than hello interval


Related options -



References -

Table 102 helloInterval (OSPF keepalive message transmission interval) (Cont.)

Parameter name Identifier of the plain Ethernet interface

Abbreviated name ieifId

3GPP name -

Managed Object IEIF

Multiplicity 1

Description This parameter identifies the unique plain ethernet interface object in the BTS. Value is always 1. "FIIB, FILB, FTIA, FTIB, FTJA, FTLB" are supported for IEIF-1. "FTFB, FTIF and FIIF" are supported for IEIF-1 only in IubIP and DualIub mode. "FSM and FSI" are supported for IEIF-1 in IubIP mode.

Range 1

Step -

Units characters

Table 103 ieifId (Identifier of the plain Ethernet interface)

DN70577885 163



19.5 interfaceArea (OSPF interface area)



Default value 1

Default value notes Always 1.

Related functions -




Related options -



References -

Table 103 ieifId (Identifier of the plain Ethernet interface) (Cont.)

Parameter name OSPF interface area

Abbreviated name interfaceArea

3GPP name -

Managed Object IEIF

Multiplicity 1

Description This parameter specifies the OSPF area to which the interface belongs.

Range 0...15

Step -

Units characters



Default value -

Default value notes Empty value means, OSPF is disabled on this inter-face.

Related functions -


Table 104 interfaceArea (OSPF interface area)

164 DN70577885



IEIF Parameters

19.6 ipAddr (IP Address Info in the Transport Network)






References -

Table 104 interfaceArea (OSPF interface area) (Cont.)

Parameter name IP Address Info in the Transport Network

Abbreviated name ipAddr

3GPP name -

Managed Object IEIF

Multiplicity 1

Description Primary and - optionally - secondary IP address of the BTS in the transport network. Both are accom-panied with a subnet mask.

In this release only the primary IP address shall be used.


-

Default value -


Related functions -

Child parameters – localIpAddr– netmask




Related options -


Table 105 ipAddr (IP Address Info in the Transport Network)

DN70577885 165



19.7 localIpAddr (Local Address of the IP Interface)


References -

Table 105 ipAddr (IP Address Info in the Transport Network) (Cont.)

Parameter name Local Address of the IP Interface

Abbreviated name localIpAddr

3GPP name -

Managed Object -

Multiplicity 1

Description IP address of the BTS in the transport network. It is accompanied with a subnet mask.

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 106 localIpAddr (Local Address of the IP Interface)

166 DN70577885



IEIF Parameters

19.8 netmask (IP Network Mask)

19.9 mtu (Maximum transfer unit)

Parameter name IP Network Mask

Abbreviated name netmask

3GPP name -

Managed Object -

Multiplicity 1

Description Network mask for the IP address of the BTS in the transport network. To be entered in dotted decimal format.

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 107 netmask (IP Network Mask)

Parameter name Maximum transfer unit

Abbreviated name mtu

3GPP name -

Managed Object IEIF

Table 108 mtu (Maximum transfer unit)

DN70577885 167



19.10 mtuMismatchDetection (MTU mismatch detection in use)

Multiplicity 1

Description This is the maximum transfer unit in octets. In this release it has fixed value 1500.

Range 1500... 1500

Step 1

Units octets



Default value 1500

Default value notes Fixed value 1500.

Related functions -




Related options – RAN74 Native Iub IP for Flexi WCDMA BTS– RAN1449 Dual Iub for Flexi WCDMA



References -

Table 108 mtu (Maximum transfer unit) (Cont.)

Parameter name MTU mismatch detection in use

Abbreviated name mtuMismatchDetection

3GPP name -

Managed Object IEIF

Multiplicity 1

Description If set to true, this parameter enables OSPF MTU mismatch detection on receiving DBD (Data Base Descriptor) packets on this interface.


Step -

Units -

Table 109 mtuMismatchDetection (MTU mismatch detection in use)

168 DN70577885



IEIF Parameters

19.11 ospfWithBfd (OSPF uses additionally BFD)


– false => 0 – true => 1



Related functions -







References -

Table 109 mtuMismatchDetection (MTU mismatch detection in use) (Cont.)

Parameter name OSPF uses additionally BFD

Abbreviated name ospfWithBfd

3GPP name -

Managed Object IEIF

Multiplicity 1

Description If set to true the OSPF router shall use Bidirectional Forwarding Detection (BFD) for detecting link inter-ruptions on this interface. If set to false, the OSPF router only uses keepalive Hello messages.


Step -

Units -


– false => 0 – true => 1


Default value notes The OSPF router does not use BFD but only Hello messages.

Table 110 ospfWithBfd (OSPF uses additionally BFD)

DN70577885 169



19.12 proxyArpIpAddrList (List of proxy ARP IP addresses for this interface.)

Related functions -


Related parameters iHSPAmode of IPNO - In iHS-PAmode only ManualBfdSession is supported.


Related options – RAN2359 OSPF enhancements



References -

Table 110 ospfWithBfd (OSPF uses additionally BFD) (Cont.)

Parameter name List of proxy ARP IP addresses for this interface.

Abbreviated name proxyArpIpAddrList

3GPP name -

Managed Object IEIF

Multiplicity 16

Description This parameter holds a list of up to 16 IP addresses that can be used for proxy ARP detection.

The format of each IP address in the list is dotted decimal.

An empty list means the feature is not used.

Range 7...15

Step -

Units characters



Default value -


Related functions -


Table 111 proxyArpIpAddrList (List of proxy ARP IP addresses for this interface.)

170 DN70577885



IEIF Parameters

19.13 qosEnabled (QOS traffic priorisation enabling flag)



Related options -

Feature dependencies – RAN2083 ProxyARP in BTS


References -


Parameter name QOS traffic priorisation enabling flag

Abbreviated name qosEnabled

3GPP name -

Managed Object IEIF

Multiplicity 1

Description This parameter specifies if multiple queues are used over this interface or only a single one. Multiple queues allow DSCP based traffic priorisa-tion.

Amongst the active interfaces (IEIF or IVIF managed object instances) there shall be at least one and at most 2 interfaces carrying a multiple queue scheduler. So qosEnabled shall have value true for at least one active interface and must not have value true on more than 2 active interfaces.


Step -

Units -


– false => 0 – true => 1


Default value notes By default a 6 PHB qeueue scheduler is indeed installed on the plain IP interface.

Related functions -


Table 112 qosEnabled (QOS traffic priorisation enabling flag)

DN70577885 171



19.14 retransInterval (OSPF LSA retransmission interval)

Related parameters localIpAddr of IEIF - Parameter qosEnabled is only relevant in case the interface is in use, i.e. in case the localIpAddr is different from 0.0.0.0.

iHSPAmode of IPNO - If iHS-PAmode is set to enabled then this value is set to 'true' internally.


Related options -



References -

Table 112 qosEnabled (QOS traffic priorisation enabling flag) (Cont.)

Parameter name OSPF LSA retransmission interval

Abbreviated name retransInterval

3GPP name -

Managed Object IEIF

Multiplicity 1

Description This parameter specifies the value for the retrans-mission of Link State Advertisement (LSA) messages for OSPF. Currently values of 1s and 2s are not supported for LSA retransmission interval .

This issue is to be resolved in the future release of the software.

Range 1... 65535

Step 1

Units -



Default value 5


Related functions -


Table 113 retransInterval (OSPF LSA retransmission interval)

172 DN70577885



IEIF Parameters

19.15 routerDeadInterval (OSPF router read interval)






References -

Table 113 retransInterval (OSPF LSA retransmission interval) (Cont.)

Parameter name OSPF router read interval

Abbreviated name routerDeadInterval

3GPP name -

Managed Object IEIF

Multiplicity 1

Description This parameter specifies the value for OSPF router dead interval in seconds. If no hello packet is received within the router dead interval, the link is assumed to be down.

Range 1... 65535

Step 1

Units -



Default value 4


Related functions -



helloInterval of IEIF - Router dead interval should be greater than hello interval


Table 114 routerDeadInterval (OSPF router read interval)

DN70577885 173



19.16 sbs (Shaper burst size)




References -

Table 114 routerDeadInterval (OSPF router read interval) (Cont.)

Parameter name Shaper burst size

Abbreviated name sbs

3GPP name -

Managed Object IEIF

Multiplicity 1

Description This parameter holds the shaper burst size for the interface.

Range 1522... 2000000

Step 1

Units -



Default value 1522


Related functions -


Related parameters localIpAddr of IEIF - Parameter sbs is only relevant in case the interface is in use, i.e. in case the localIpAddr is different from 0.0.0.0.

trafficPathShapingEnable of IEIF - Parameter sbs is only relevant in case parameter trafficPathShapingEnable has value TPS_PATH.





Table 115 sbs (Shaper burst size)

174 DN70577885



IEIF Parameters

19.17 sbsTotal (Total shaper burst size)


References -

Table 115 sbs (Shaper burst size) (Cont.)

Parameter name Total shaper burst size

Abbreviated name sbsTotal

3GPP name -

Managed Object IEIF

Multiplicity 1

Description The Total Shaper Burst Size ("SBS") defines the maximum burst size that is allowed to pass at the output of the WFQ aggregator.

Range 1522... 2000000

Step 1

Units octets



Default value 1522


Related functions -


Related parameters trafficPathShapingEnable of IEIF - Parameter sbsTotal is only relevant in case parameter trafficPathShapingEnable has value TPS_WFQ.






Table 116 sbsTotal (Total shaper burst size)

DN70577885 175



19.18 shapedBandwidth (Shaped Bandwidth)

References -

Table 116 sbsTotal (Total shaper burst size) (Cont.)

Parameter name Shaped Bandwidth

Abbreviated name shapedBandwidth

3GPP name -

Managed Object IEIF

Multiplicity 1

Description This is the egress shaping bandwidth on the network interface (in kbit/s).

The related parameter upperLayingShaping decides if shaping is for the IP layer only or if the ethernet overhead is taken into account.

Values above 100 MBit/s are only allowed on Gigabit Ethernet interfaces.

Transport Ethernet interface bandwidth available for the traffic is defined by this param if shaping type (IEIF/trafficPathShapingEnable) is OFF or PATH. Bandwidth used by possibly configured CEoPSN reduces the available bandwidth. The sum of cir values of all configured IP interfaces (IEIF / IVIF) and cir of Ethernet Service OAM multiplied by 1.2 cannot exceed the available Transport Ethernet interface bandwidth. “cir” of Service OAM is taken in count if there exist at least one OAMMEP in the system.

Range 500... 1000000

Step 100

Units kbit/s




Default value notes The default is 1000000 (1 Gigabit/s) for Gigabit Ethernet interfaces.

Related functions -


Table 117 shapedBandwidth (Shaped Bandwidth)

176 DN70577885



IEIF Parameters

19.19 sir (Shaper information rate)

Related parameters upperLayerShaping of IEIF

trafficPathShapingEnable of IEIF - Transport Ethernet interface bandwidth available for the traffic is defined by this param if shaping type (IEIF/trafficPathShapingEnable) is OFF or PATH.


Related options -



References -

Table 117 shapedBandwidth (Shaped Bandwidth) (Cont.)

Parameter name Shaper information rate

Abbreviated name sir

3GPP name -

Managed Object IEIF

Multiplicity 1

Description This parameter holds the shaper information rate for the interface.

The maximum value of this parameter is 100 MBps for Fast Ethernet interfaces and 1 GBps for Gigabit Ethernet interfaces.

Range 100... 1000000

Step 100

Units -





Related functions -


Table 118 sir (Shaper information rate)

DN70577885 177



19.20 sirTotal (Total shaper information rate)

Related parameters localIpAddr of IEIF - Parameter sir is only relevant in case the interface is in use, i.e. in case the localIpAddr is different from 0.0.0.0.

trafficPathShapingEnable of IEIF - Parameter sir is only relevant in case parameter trafficPathShapingEnable has value TPS_PATH.






References -

Table 118 sir (Shaper information rate) (Cont.)

Parameter name Total shaper information rate

Abbreviated name sirTotal

3GPP name -

Managed Object IEIF

Multiplicity 1

Description This parameter holds the total Shaper Information Rate ("SIR") at the output of the WFQ aggregator.

The maximum value of this parameter is 100 MBps for Fast Ethernet interfaces and 1 GBps for Gigabit Ethernet interfaces.

Transport Ethernet interface bandwidth available for the traffic is defined by this param if shaping type (IEIF/trafficPathShapingEnable) is WFQ. Band-width used by possibly configured CEoPSN reduces the available bandwidth. The sum of cir values of all configured IP interfaces (IEIF / IVIF) and cir of Ethernet Service OAM multiplied by 1.2 cannot exceed the available Transport Ethernet interface bandwidth. “cir” of Service OAM is taken in count if there exists at least one OAMMEP in the system.

Table 119 sirTotal (Total shaper information rate)

178 DN70577885



IEIF Parameters

19.21 trafficPathShapingEnable (Traffic path shaping enabling flag)

Range 100... 1000000

Step 100

Units kbps





Related functions -


Related parameters trafficPathShapingEnable of IEIF - Parameter sirTotal is only relevant in case param-eter trafficPathShapingEnable has value TPS_WFQ.






References -

Table 119 sirTotal (Total shaper information rate) (Cont.)

Parameter name Traffic path shaping enabling flag

Abbreviated name trafficPathShapingEnable

3GPP name -

Managed Object IEIF

Multiplicity 1

Table 120 trafficPathShapingEnable (Traffic path shaping enabling flag)

DN70577885 179



Description This parameters decides on the type of shaping in case of VLANs. When traffic path shaping is enabled, shaping at the level of each VLAN enabled, else shaping at the WFQ aggregator level is enabled. Shaping may also be switched off entirely.

Transport Ethernet interface bandwidth available is dependent on this param (see IEIF/shapedBand-width and IEIF/sirTotal ).

Range TPS_OFF (0), TPS_WFQ (1), TPS_PATH (2)

Step -

Units -


gui ==> internal

TPS_OFF ==> 0

TPS_WFQ ==> 1

TPS_PATH ==> 2

Default value TPS_WFQ (1)


Related functions -


Related parameters shapedBandwidth of IEIF - Transport Ethernet interface bandwidth available is dependent on this param (see IEIF/shapedBand-width and IEIF/sisTota;l).

sirTotal of IEIF - Transport Ethernet interface bandwidth available is depen-dent on this param (see IEIF/shapedBandwidth and IEIF/sisTotal).






References -

Table 120 trafficPathShapingEnable (Traffic path shaping enabling flag) (Cont.)

180 DN70577885



IEIF Parameters

19.22 transmitDelay (OSPF packet transmission delay)

19.23 upperLayerShaping (Upper Layer Shaping Enabled Flag)

Parameter name OSPF packet transmission delay

Abbreviated name transmitDelay

3GPP name -

Managed Object IEIF

Multiplicity 1

Description This parameter specifies the OSPF transmit delay. This is the amount of time added to the age of an OSPF Link State Update (LSU) packet before transmitting it. It is the estimated number of seconds to transmit a packet over the interface.

Range 1... 65535

Step 1

Units -



Default value 1


Related functions -







References -

Table 121 transmitDelay (OSPF packet transmission delay)

Parameter name Upper Layer Shaping Enabled Flag

Abbreviated name upperLayerShaping

3GPP name -

Table 122 upperLayerShaping (Upper Layer Shaping Enabled Flag)

DN70577885 181



19.24 vlanEnabled (Vlan Enabled flag)

Managed Object IEIF

Multiplicity 1

Description This parameter decides if shaping takes the ethernet overhead into account when shaping the bandwidth or not. If the flag has value true, the associated shapedBandwidth is the bandwidth on the IP layer only. If the flag has value false the Ethernet header is counted also. Use "true" for an IP only network, e.g. xDSL, use "false" for an Ethernet network, e.g. Metro Ethernet.


Step -

Units -


– false => 0 – true => 1

Default value -


Related functions -




Related options -



References -

Table 122 upperLayerShaping (Upper Layer Shaping Enabled Flag) (Cont.)

Parameter name Vlan Enabled flag

Abbreviated name vlanEnabled

3GPP name -

Managed Object IEIF

Multiplicity 1

Table 123 vlanEnabled (Vlan Enabled flag)

182 DN70577885



IEIF Parameters

19.25 vlanId (Vlan ID)

Description This flag indicates if Vlan mapping is enabled for this ethernet interface. Value "true" means that Vlan mapping is enabled. In case Vlan mapping is not enabled, all messages on the interface will be sent in plain format.


Step -

Units -


– false => 0 – true => 1



Related functions -




Related options -



References -

Table 123 vlanEnabled (Vlan Enabled flag) (Cont.)

Parameter name Vlan ID

Abbreviated name vlanId

3GPP name -

Managed Object IEIF

Multiplicity 1

Description Vlan ID to be used over this ethernet interface. The parameter is only relevant if vlan mapping is enabled (parameter Vlan Enabled flag has value true).

Range 0... 4094

Table 124 vlanId (Vlan ID)

DN70577885 183



Step 1

Units -



Default value -


Related functions -


Related parameters vlanEnabled of IEIF


Parameter relationships Parameter Vlan ID is only relevant if parameter Vlan Enabled flag has value true.

Related options -



References -

Table 124 vlanId (Vlan ID) (Cont.)

184 DN70577885



IHCP Parameters

20 IHCP Parameters

20.1 client_identifier (Entry set for DHCP clients identified by a system name)

20.2 dhcpClientIdentifier (DHCP Client Identifier)

Parameter name Entry set for DHCP clients identified by a system name

Abbreviated name client_identifier

3GPP name -

Managed Object IHCP

Multiplicity 10

Description This is a set of entries in the DHCP database in which an IP address is assigned to a DHCP client that identifies itself at the BTS by a system name (by a "text string").


-

Default value -


Related functions -

Child parameters – dhcpClientIdentifier– dhcpFixedIpAddress




Related options -

Feature dependencies – DHCP Server


References -

Table 125 client_identifier (Entry set for DHCP clients identified by a system name)

Parameter name DHCP Client Identifier

Abbreviated name dhcpClientIdentifier

Table 126 dhcpClientIdentifier (DHCP Client Identifier)

DN70577885 185

Flexi Transport Module Parameters IHCP Parameters


20.3 dhcpFixedIpAddress (DHCP Fixed IP Address)

3GPP name -

Managed Object -

Multiplicity 1

Description This is a unique string used in the DHCP server of the BTS for identifying a DHCP client that is assigned a fixed IP address.

This may either be one of the predefined names "RET1" (Remote Electrical Tilt), "RET2", "BBU" and "LMU" or a user-defined name consisting of up to 20 digits [0-9] and letters [a-z] and [A-Z].

Range 1...20

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 126 dhcpClientIdentifier (DHCP Client Identifier) (Cont.)

Parameter name DHCP Fixed IP Address

Abbreviated name dhcpFixedIpAddress

3GPP name -

Managed Object -

Multiplicity 1

Table 127 dhcpFixedIpAddress (DHCP Fixed IP Address)

186 DN70577885



IHCP Parameters

20.4 dhcpAccessId (DHCP Server Identifier)

Description Specifies a fixed IP address to be assigned to the DHCP client if it requests a lease with the specified client-identifier.

The IP address must be within the public IP subnet of the LMP. However, neither the IP addresses of the BTS nor its subnet IP address can be used.

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 127 dhcpFixedIpAddress (DHCP Fixed IP Address) (Cont.)

Parameter name DHCP Server Identifier

Abbreviated name dhcpAccessId

3GPP name -

Managed Object IHCP

Multiplicity 1

Description This parameter identifies the unique DHCP Server object in the BTS. Value is always 1.

Range 1... 1

Step 1

Units -

Table 128 dhcpAccessId (DHCP Server Identifier)

DN70577885 187



20.5 hardware_identifier (Entry set of DHCP clients identified by a MAC address)



Default value -


Related functions -




Related options -



References -

Table 128 dhcpAccessId (DHCP Server Identifier) (Cont.)

Parameter name Entry set of DHCP clients identified by a MAC address

Abbreviated name hardware_identifier

3GPP name -

Managed Object IHCP

Multiplicity 10

Description This is set of entries in the DHCP database of the BTS that binds an IP address to a DHCP client that identifies itself at BTS by a hardware address (by a "MAC address").


-

Default value -


Related functions -

Child parameters – dhcpFixedIpAddress– dhcpHardwareIdentifier


Table 129 hardware_identifier (Entry set of DHCP clients identified by a MAC address)

188 DN70577885



IHCP Parameters

20.6 dhcpFixedIpAddress (DHCP Fixed IP Address)



Related options -



References -

Table 129 hardware_identifier (Entry set of DHCP clients identified by a MAC address) (Cont.)

Parameter name DHCP Fixed IP Address

Abbreviated name dhcpFixedIpAddress

3GPP name -

Managed Object -

Multiplicity 1

Description Specifies the fixed IP address to be assigned to the DHCP client if it requests a lease with the hardware (MAC) address specified in parameter "DHCP Hardware Identifier".

The IP address must be within the public IP subnet of the LMP. However, the IP addresses of the BTS, its subnet IP address and its broadcast IP address cannot be used.

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -

Table 130 dhcpFixedIpAddress (DHCP Fixed IP Address)

DN70577885 189



20.7 dhcpHardwareIdentifier (DHCP Hardware Identifier)



References -

Table 130 dhcpFixedIpAddress (DHCP Fixed IP Address) (Cont.)

Parameter name DHCP Hardware Identifier

Abbreviated name dhcpHardwareIdentifier

3GPP name -

Managed Object -

Multiplicity 1

Description This is the unique hardware (MAC) address within the DHCP server of the BTS by which a DHCP client identifies itself at the BTS. The server will then assign the IP address of parameter "DHCP Fixed IP Address" to the client.

Range 17

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 131 dhcpHardwareIdentifier (DHCP Hardware Identifier)

190 DN70577885



IHCP Parameters

20.8 range_identifier (DHCP server IP address pool)

20.9 dhcpRangeEnd (DHCP Range End IP Address)

Parameter name DHCP server IP address pool

Abbreviated name range_identifier

3GPP name -

Managed Object IHCP

Multiplicity 1

Description This entry reserves an IP address range to be used for assignments for the DHCP clients.


-

Default value -


Related functions -

Child parameters – dhcpRangeEnd– dhcpRangeStart




Related options -



References -

Table 132 range_identifier (DHCP server IP address pool)

Parameter name DHCP Range End IP Address

Abbreviated name dhcpRangeEnd

3GPP name -

Managed Object -

Multiplicity 1

Table 133 dhcpRangeEnd (DHCP Range End IP Address)

DN70577885 191



20.10 dhcpRangeStart (DHCP Range Start IP Address)

Description Specifies the final IP address of the DHCP IP address range.

The IP address must be within the public IP subnet of the LMP.

However, neither the IP addresses of the BTS nor its subnet IP address shall be used.

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 133 dhcpRangeEnd (DHCP Range End IP Address) (Cont.)

Parameter name DHCP Range Start IP Address

Abbreviated name dhcpRangeStart

3GPP name -

Managed Object -

Multiplicity 1

Table 134 dhcpRangeStart (DHCP Range Start IP Address)

192 DN70577885



IHCP Parameters

Description Specifies the starting IP address of the DHCP IP address range.

The IP address must be within the public IP subnet of the LMP.

However, neither the IP addresses of the BTS nor its subnet IP address shall be used.

Range 0...15

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 134 dhcpRangeStart (DHCP Range Start IP Address) (Cont.)

DN70577885 193

Flexi Transport Module Parameters IMAG Parameters


21 IMAG Parameters




3GPP name -

Managed Object IMAG

Multiplicity 1

Description Used to lock and unlock the IMA group.

When the Adminstrative State is locked, the IMA group is deactivated. All alarms and any ATM cell transfer is suppressed. Unlocking the Administra-tive State will trigger the creation of a TCTT (ATM interface).

Note that setting the Administrative State to locked will not delete the associated TCTT.

Changing the value for an IMA group also changes the Administrative State of the physical interfaces assigned to the group.


Step -

Units -


gui ==> internal

locked ==> 0

unlocked ==> 1



Related functions -




Related options -

Feature dependencies – Inverse Multiplexing (IMA)



194 DN70577885



IMAG Parameters

21.2 imaGroupId (IMA group identifier)

References -

Table 135 administrativeState (Administrative State) (Cont.)

Parameter name IMA group identifier

Abbreviated name imaGroupId

3GPP name -

Managed Object IMAG

Multiplicity 1

Description This parameter identifies the IMA group.

Format: unit#-imag#

where

unit#: always 1 (unit number)

imag#: 33..75 (IMA group number on the unit)

Range 4

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 136 imaGroupId (IMA group identifier)

DN70577885 195



21.3 imaVersionId (IMA Version Identifier)

Parameter name IMA Version Identifier

Abbreviated name imaVersionId

3GPP name -

Managed Object IMAG

Multiplicity 1

Description Specifies the standard according to which the IMA group is operating.

ATM Forum af-phy-0086.000 allows for two inter-pretations: IMA version 1.0 and IMA version 1.0Alt (alternate). ATM Forum af-phy-0086.001 elimi-nates this ambiguity and is the basis for IMA version 1.1. This version is the most common one.

The Transport Module provides also an option to atomatically detect the correct IMA version (default).

IMA version 1.0 is not supported

The value must be the same at both local and remote site.

Range imaVersion10Alt (1), imaVersion11 (2), automatic (3)

Step -

Units -


gui ==> internal

imaVersion10Alt ==> 1

imaVersion11 ==> 2

automatic ==> 3

Default value automatic (3)


Related functions -




Related options -



Table 137 imaVersionId (IMA Version Identifier)

196 DN70577885



IMAG Parameters


21.5 interfaces (Physical interface list)

References -

Table 137 imaVersionId (IMA Version Identifier) (Cont.)



3GPP name -

Managed Object IMAG

Multiplicity 1

Description This parameter holds the IMA Group identifier.

Range 33... 75

Step 1

Units -



Default value -


Related functions -




Related options -



References -


Parameter name Physical interface list

Abbreviated name interfaces

3GPP name -

Managed Object IMAG

Table 139 interfaces (Physical interface list)

DN70577885 197



21.6 minNumLinks (Minimum Number of Links)

Multiplicity 16

Description This parameter holds the list of the physical inter-faces used by the IMA group.

The maximum number of interfaces in one IMA group depends on the unit type:


FTEB, FTPB, FTFA, FTIF, FIIF: 1..8

FTFA, FTHA, FTFB: 1..16

Range 0... 16

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 139 interfaces (Physical interface list) (Cont.)

Parameter name Minimum Number of Links

Abbreviated name minNumLinks

3GPP name -

Managed Object IMAG

Multiplicity 1

Table 140 minNumLinks (Minimum Number of Links)

198 DN70577885



IMAG Parameters


Description Specifies the minimum number of IMA links required to keep the IMA group operable.

If the number of working IMA links is smaller, the IMA group is out of use.

Range 1... 16

Step 1

Units -



Default value 1


Related functions -




Related options -



References -

Table 140 minNumLinks (Minimum Number of Links) (Cont.)



3GPP name -

Managed Object IMAG

Multiplicity 1


Range 1... 1

Step 1

Units -


DN70577885 199





Default value -


Related functions -




Related options -



References -


200 DN70577885



INTP Parameters

22 INTP Parameters

22.1 ntpAccessId (NTP Identifier)

22.2 ntpServers (List of NTP Server IP Addresses)

Parameter name NTP Identifier

Abbreviated name ntpAccessId

3GPP name -

Managed Object INTP

Multiplicity 1

Description This parameter identifies the unique NTP configu-ration entity of the BTS. The value is always 1.

Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 142 ntpAccessId (NTP Identifier)

Parameter name List of NTP Server IP Addresses

Abbreviated name ntpServers

3GPP name -

Managed Object INTP

Table 143 ntpServers (List of NTP Server IP Addresses)

DN70577885 201

Flexi Transport Module Parameters INTP Parameters


Multiplicity 3

Description Specifies the IP addresses of the NTP servers.

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -

Feature dependencies – NTP Server


References -

Table 143 ntpServers (List of NTP Server IP Addresses) (Cont.)

202 DN70577885



IPNO Parameters

23 IPNO Parameters

23.1 bfdHoldUpTime (BFD throttle time for re-installing protec-tion routes)

Parameter name BFD throttle time for re-installing protection routes

Abbreviated name bfdHoldUpTime

3GPP name -

Managed Object IPNO

Multiplicity 1

Description This parameter specifies the delay for re-installig routes as active ones after a BFD session has recovered from down to up state. Defining a delay can prevent too heavy toggling of de-installing and re-installing routes for unstable BFD sessions.

Range 0... 900

Step 1

Units seconds



Default value 0


Related functions -




Related options – RAN2440 Fast IP Rerouting



References -

Table 144 bfdHoldUpTime (BFD throttle time for re-installing protection routes)

DN70577885 203

Flexi Transport Module Parameters IPNO Parameters


23.2 btsId (BTS Identifier)

23.3 btsIpAddr (Base Station IP Address)

Parameter name BTS Identifier

Abbreviated name btsId

3GPP name -

Managed Object IPNO

Multiplicity 1

Description Base Station Identifier.

Reserved Values: 0 = "BTS not configured" and 0xFFFF (=65535) = "RNC not configured"

Range 1... 65534

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 145 btsId (BTS Identifier)

Parameter name Base Station IP Address

Abbreviated name btsIpAddr

3GPP name -

Managed Object IPNO

Multiplicity 1

Table 146 btsIpAddr (Base Station IP Address)

204 DN70577885



IPNO Parameters

23.4 cPlaneIpAddress (Control-plane application IP address)

Description IP Address of the Base Station.

Address under which the Base Station is available remotely.

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 146 btsIpAddr (Base Station IP Address) (Cont.)

Parameter name Control-plane application IP address

Abbreviated name cPlaneIpAddress

3GPP name -

Managed Object IPNO

Multiplicity 1

Table 147 cPlaneIpAddress (Control-plane application IP address)

DN70577885 205



Description This parameter specifies the IP address to be used for control-plane traffic by the FTM.

This IP address can collapse with the local IP address of the plain Ethernet interface (IEIF object) or with the local IP address of one of the VLAN interfaces (IVIF object) or with the local IP address of the ML-PPP interface (P3SL or P3ML object) of the FTM. If it does not collapse with such network interface IP address, the IP address is virtual.

The format of this parameter is dotted decimal.

Value 0.0.0.0 means the control-plane application IP address is not used.

The parameter is not used at all in case of AtmOv-erEthernet (AtmIub) and in case of Dual Iub mode.

Range 7...15

Step -

Units characters



Default value 0.0.0.0

Default value notes By default the control-plane application IP address is not used.

Related functions -


Related parameters transportMode of IPNO - Parameter cPlaneIpAddress is irrelevant in case parameter transportMode has value AtmOverEthernet and in case parameter transportMode has value DualIub.


Related options -



References -

Table 147 cPlaneIpAddress (Control-plane application IP address) (Cont.)

206 DN70577885



IPNO Parameters

23.5 cesopsnIpAddress (CES over PSN application IP address)

Parameter name CES over PSN application IP address

Abbreviated name cesopsnIpAddress

3GPP name -

Managed Object IPNO

Multiplicity 1

Description This parameter specifies the application IP address for CES over PSN.

The address can collapse with the IP address of the plain Ethernet interface (IEIF object) or with the IP address of one of the VLAN interfaces (IVIF object). If it does not collapse with such network interface IP address, the CES over PSN IP address is virtual.


Value 0.0.0.0 means the CES over PSN IP address is not used.

The parameter is not used at all in case of AtmOv-erEthernet (AtmIub) and in DualIub mode.

Range 7...15

Step -

Units characters




Default value notes By default the CES over PSN application IP address is not used.

Related functions -


Related parameters transportMode of IPNO - Parameter cesopsnIpAddress is irrelevant in case parameter transportMode has value AtmOverEthernet and in case parameter transportMode has value DualIub.

administrativeState of P3SL - Parameter cesopsnIpAddress is irrelevant in case parameter administrativeState has value unlocked.

administrativeState of P3ML - Parameter cesopsnIpAddress is irrelevant in case parameter administrativeState has value unlocked.


Table 148 cesopsnIpAddress (CES over PSN application IP address)

DN70577885 207



23.6 disableFtp (Disable FTP server)

Related options -



References -

Table 148 cesopsnIpAddress (CES over PSN application IP address) (Cont.)

Parameter name Disable FTP server

Abbreviated name disableFtp

3GPP name -

Managed Object IPNO

Multiplicity 1

Description Control whether to allow/disallow running FTP server on Transport module for security reasons. FSMr3 HW units are not supported.

Range FTP_SERVER_ENABLED (0), FTP_SERVER_DISABLED (1)

Step -

Units -


gui ==> internal

FTP_SERVER_ENABLED ==> 0

FTP_SERVER_DISABLED ==> 1

Default value FTP_SERVER_ENABLED (0)


Related functions -




Related options -



References -

Table 149 disableFtp (Disable FTP server)

208 DN70577885



IPNO Parameters

23.7 flexBusIpAddr (Public IP Address of Flexbus Part of BTS)

23.8 fpLocalUdpPort (Local UDP port for small packets multi-plexing)

Parameter name Public IP Address of Flexbus Part of BTS

Abbreviated name flexBusIpAddr

3GPP name -

Managed Object IPNO

Multiplicity 1

Description Public IP address of the Flexbus part of the unit. In dotted decimal format.

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 150 flexBusIpAddr (Public IP Address of Flexbus Part of BTS)

Parameter name Local UDP port for small packets multiplexing

Abbreviated name fpLocalUdpPort

3GPP name -

Managed Object IPNO

Multiplicity 1

Table 151 fpLocalUdpPort (Local UDP port for small packets multiplexing)

DN70577885 209



23.9 fpMuxAmount (Maximum amount of small packets that can be multiplexed)

Description This parameter specifies the port on which the FTM expects to receive multiplexed frames. Multiplexing small packets shall increase the efficiency when transporting them.

Range 49152... 65535

Step 1

Units -



Default value 65535


Related functions -




Related options -

Feature dependencies – RAN1886 Efficient Transport for Small IP Packets


References -

Table 151 fpLocalUdpPort (Local UDP port for small packets multiplexing) (Cont.)

Parameter name Maximum amount of small packets that can be mul-tiplexed

Abbreviated name fpMuxAmount

3GPP name -

Managed Object IPNO

Multiplicity 1

Table 152 fpMuxAmount (Maximum amount of small packets that can be multiplexed)

210 DN70577885



IPNO Parameters

23.10 fpMuxDelay (Small packets multiplexing delay time)

Description This parameter specifies the maximum amount of non-multiplexed packets that are multiplexed to a single multiplexed one. Multiplexing small packets shall increase the efficiency when transporting them.

Range 1... 30

Step 1

Units -



Default value 30


Related functions -




Related options -



References -

Table 152 fpMuxAmount (Maximum amount of small packets that can be multiplexed) (Cont.)

Parameter name Small packets multiplexing delay time

Abbreviated name fpMuxDelay

3GPP name -

Managed Object IPNO

Multiplicity 1

Table 153 fpMuxDelay (Small packets multiplexing delay time)

DN70577885 211



23.11 fpRemoteUdpPort (Remote UDP port for small packets multiplexing)

Description This parameter specifies maximum delay time that may elapse before transmitting a multiplexed packet. As long as the timer has not elapsed, the FTM waits for other incoming packets in order to multiplex them additionally with the packet that is wating to be transmitted. Multiplexing small packets shall increase the efficiency when transporting them.

Range 1... 4

Step 1

Units -



Default value 2


Related functions -




Related options -



References -

Table 153 fpMuxDelay (Small packets multiplexing delay time) (Cont.)

Parameter name Remote UDP port for small packets multiplexing

Abbreviated name fpRemoteUdpPort

3GPP name -

Managed Object IPNO

Multiplicity 1

Table 154 fpRemoteUdpPort (Remote UDP port for small packets multiplexing)

212 DN70577885



IPNO Parameters

23.12 ftmIpAddr (Flexi Transport Module IP Address)

Description This parameter specifies the port of the RNC towards which the FTM sends multiplexed frames. Multiplexing small packets shall increase the effi-ciency when transporting them.

Range 49152... 65535

Step 1

Units -



Default value 65535


Related functions -




Related options -



References -

Table 154 fpRemoteUdpPort (Remote UDP port for small packets multiplexing)

Parameter name Flexi Transport Module IP Address

Abbreviated name ftmIpAddr

3GPP name -

Managed Object IPNO

Multiplicity 1

Description Public IP address of the Flexi Transport Module

Range 7...15

Step -

Units characters

Table 155 ftmIpAddr (Flexi Transport Module IP Address)

DN70577885 213



23.13 ftmNetmask (Netmask of the public IP address)



Default value -


Related functions -




Related options -



References -

Table 155 ftmIpAddr (Flexi Transport Module IP Address) (Cont.)

Parameter name Netmask of the public IP address

Abbreviated name ftmNetmask

3GPP name -

Managed Object IPNO

Multiplicity 1

Description This parameter specifies the subnet mask of the public IP address of the transport module.

Range 7...15

Step -

Units characters



Default value -


Related functions -




Table 156 ftmNetmask (Netmask of the public IP address)

214 DN70577885



IPNO Parameters

23.14 iHSPAAdapterCommissioningParameter (I-HSPA adapter initial commissioning parameters)

Related options -



References -

Table 156 ftmNetmask (Netmask of the public IP address) (Cont.)

Parameter name I-HSPA adapter initial commissioning parameters

Abbreviated name iHSPAAdapterCommissioningParameter

3GPP name -

Managed Object IPNO

Multiplicity 100

Description Defines the parameters which are needed for the initial commissioning of the I-HSPA adapter.

Range 0...255

Step -

Units characters



Default value -


Related functions -

Modification BTS restart needed



Related options – RAN2060 Conversion of a BTS containing FTLB into an I-BTS


Interfaces – EM -> FTM– RAC -> FTM– RAC <-> RACApp

References -

Table 157 iHSPAAdapterCommissioningParameter (I-HSPA adapter initial commis-sioning parameters)

DN70577885 215



23.15 iHSPAmode (I-HSPA mode activation flag)

23.16 icmpResponseEnabled (Enable response to ICMP traffic)

Parameter name I-HSPA mode activation flag

Abbreviated name iHSPAmode

3GPP name -

Managed Object IPNO

Multiplicity 1

Description This parameter defines whether the BTS shall be operated in I-HSPA mode.

A prerequisite is that the I-HSPA SW support is enabled. This can be viewed from parameter IPNO - iHSPASwSupport.

Range disabled (0), enabled (1)

Step -

Units -


gui ==> internal

disabled ==> 0

enabled ==> 1

Default value disabled (0)

Default value notes Default is disabled I-HSPA mode.

Related functions -




Related options – RAN2060 Conversion of a BTS containing FTLB into an I-BTS



References -

Table 158 iHSPAmode (I-HSPA mode activation flag)

Parameter name Enable response to ICMP traffic

Abbreviated name icmpResponseEnabled

Table 159 icmpResponseEnabled (Enable response to ICMP traffic)

216 DN70577885



IPNO Parameters

23.17 ipNodeId (IP Node Identifier)

3GPP name -

Managed Object IPNO

Multiplicity 1

Description This parameter controls if the BTS shall respond to ICMP and traceroute requests via BTS Site Manager or SCF or not at all. Value false means: response is disabled.


Step -

Units -


– false => 0 – true => 1



Related functions -




Related options -



References -

Table 159 icmpResponseEnabled (Enable response to ICMP traffic) (Cont.)

Parameter name IP Node Identifier

Abbreviated name ipNodeId

3GPP name -

Managed Object IPNO

Multiplicity 1

Description This parameter identifies the BTS transport IP node configuration.

The value is always 1.

Range 1... 1

Table 160 ipNodeId (IP Node Identifier)

DN70577885 217



23.18 linkOAMLoopbackSupport (Link OAM remote loopback discovery enabling flag)

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 160 ipNodeId (IP Node Identifier) (Cont.)

Parameter name Link OAM remote loopback discovery enabling flag

Abbreviated name linkOAMLoopbackSupport

3GPP name -

Managed Object IPNO

Multiplicity 1

Description If set to true, the FTM enables the discovery process for Link OAM loopback requests initiated by a remote network element. If set to false, a loopback initiated from the remote network is not accepted by the FTM.


Step -

Units -


– false => 0 – true => 1

Table 161 linkOAMLoopbackSupport (Link OAM remote loopback discovery enabling flag)

218 DN70577885



IPNO Parameters

23.19 mPlaneIpAddress (Management -plane application IP address)


Default value notes By default, the FTM does not accept loopbacks ini-tiated from a remote peer.

Related functions -




Related options – RAN1880 Ethernet OAM (Ethernet Link OAM)



References -

Table 161 linkOAMLoopbackSupport (Link OAM remote loopback discovery enabling flag) (Cont.)

Parameter name Management -plane application IP address

Abbreviated name mPlaneIpAddress

3GPP name -

Managed Object IPNO

Multiplicity 1

Table 162 mPlaneIpAddress (Management -plane application IP address)

DN70577885 219



23.20 mtu (Maximum transfer unit of the BTS)

Description This parameter specifies the IP address to be used for management-plane traffic by the FTM.



Value 0.0.0.0 means the management-plane appli-cation IP address is not used.

The parameter is not used at all in case of AtmOv-erEthernet (AtmIub) mode.

Range 7...15

Step -

Units characters




Default value notes By default the management-plane application IP address is not used.

Related functions -




Related options -



References -

Table 162 mPlaneIpAddress (Management -plane application IP address) (Cont.)

Parameter name Maximum transfer unit of the BTS

Table 163 mtu (Maximum transfer unit of the BTS)

220 DN70577885



IPNO Parameters

23.21 oamCir (Committed information rate for Service OAM messages)

Abbreviated name mtu

3GPP name -

Managed Object IPNO

Multiplicity 1

Description This is the maximum transfer unit that is to be used equally on all IP interfaces of the BTS.

Range 576... 1500

Step 1

Units octets



Default value 1500


Related functions -







References -

Table 163 mtu (Maximum transfer unit of the BTS) (Cont.)

Parameter name Committed information rate for Service OAM messages

Abbreviated name oamCir

3GPP name -

Managed Object IPNO

Multiplicity 1

Table 164 oamCir (Committed information rate for Service OAM messages)

DN70577885 221



23.22 oamTlvReply (Optional TLV message reply flag)

Description This parameter specifies the committed information rate (CIR) for Service OAM messages sent by the FTM.


Range 100... 1000000

Step 100

Units kbps



Default value 1000

Default value notes Default value is 1 Mbps.

Related functions -




Related options – RAN1880 Ethernet OAM (Ethernet Service OAM)



References -

Table 164 oamCir (Committed information rate for Service OAM messages) (Cont.)

Parameter name Optional TLV message reply flag

Abbreviated name oamTlvReply

3GPP name -

Managed Object IPNO

Multiplicity 1

Table 165 oamTlvReply (Optional TLV message reply flag)

222 DN70577885



IPNO Parameters

23.23 omsTls (TLS usage towards the O&M system)

Description If this parameter is set to true, the optional TLV received in a Link Trace or Loopback message (LTM or LBM message) is sent back unchecked in the corresponding reply message (LTR, or LBR).

If this parameter is set to false, the received optional TLV is ignored and not being sent in the reply-message.


Step -

Units -


– false => 0 – true => 1


Default value notes By default TLV is ignored.

Related functions -




Related options -



References -

Table 165 oamTlvReply (Optional TLV message reply flag) (Cont.)

Parameter name TLS usage towards the O&M system

Abbreviated name omsTls

3GPP name -

Managed Object IPNO

Multiplicity 1

Table 166 omsTls (TLS usage towards the O&M system)

DN70577885 223



23.24 ret1IpAddr (RET IP Address)

Description Defines the usage of TLS between the BTS and the O&M system.

The usage of TLS requires that valid certificates are installed to the BTS.

Range off (0), forced (1), probing (2)

Step -

Units -


gui ==> internal

off ==> 0

forced ==> 1

probing ==> 2

Default value probing (2) for WN7.0 1.0;

off (0) for WN7.0 2.0


Related functions -


Related parameters iHSPAmode of IPNO - If iHS-PAmode is set to enabled, then omsTls is set to 'off'.


Related options – RAN1102 Secure BTS Management Interface



References -

Table 166 omsTls (TLS usage towards the O&M system) (Cont.)

Parameter name RET IP Address

Abbreviated name ret1IpAddr

3GPP name -

Managed Object IPNO

Multiplicity 1

Description IP Address of the RET, which is connected to the Base Station.

Table 167 ret1IpAddr (RET IP Address)

224 DN70577885



IPNO Parameters

23.25 rncIpAddr (RNC IP Address)

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 167 ret1IpAddr (RET IP Address) (Cont.)

Parameter name RNC IP Address

Abbreviated name rncIpAddr

3GPP name -

Managed Object IPNO

Multiplicity 1

Description IP Address of the RNC to which the Base Station is connected.

Range 7...15

Step -

Units characters



Default value -


Related functions -

Table 168 rncIpAddr (RNC IP Address)

DN70577885 225



23.26 sPlaneIpAddress (Synchronization-plane application IP address)




Related options -



References -

Table 168 rncIpAddr (RNC IP Address) (Cont.)

Parameter name Synchronization-plane application IP address

Abbreviated name sPlaneIpAddress

3GPP name -

Managed Object IPNO

Multiplicity 1

Description This parameter specifies the IP address to be used for synchronization-plane traffic by the FTM.



Value 0.0.0.0 means the synchronization-plane application IP address is not used.


Range 7...15

Step -

Units characters



Table 169 sPlaneIpAddress (Synchronization-plane application IP address)

226 DN70577885



IPNO Parameters

23.27 transportMode (BTS transport mode)


Default value notes By default the synchronization-plane application IP address is not used.

Related functions -


Related parameters transportMode of IPNO - Parameter sPlaneIpAddress is irrelevant in case parameter transportMode has value AtmOverEthernet.


Related options -



References -

Table 169 sPlaneIpAddress (Synchronization-plane application IP address) (Cont.)

Parameter name BTS transport mode

Abbreviated name transportMode

3GPP name -

Managed Object IPNO

Multiplicity 1

Description This parameter selects between the transport modes AtmOverEthernet, Dual Iub and Iub/IP.

Range AtmOverEthernet (0), DualIub (1), IubIP (2)

Step -

Units -


gui ==> internal

AtmOverEthernet ==> 0

DualIub ==> 1

IubIP ==> 2

Default value AtmOverEthernet (0)


Related functions -


Table 170 transportMode (BTS transport mode)

DN70577885 227



23.28 twampMessageRate (TWAMP initiator rate for sending messages)

Related parameters iHSPAmode of IPNO - If iHS-PAmode is set to enabled then only Iub/IP transport mode is supported.

administrativeState of P3SL - Iub/IP can be enabled only on the modules FTEB, FTHA, FTPB, FTFA when either Multi Link PPP or Single Link PPP is being unlocked.

administrativeState of P3ML - Iub/IP can be enabled only on the modules FTEB, FTHA, FTPB, FTFA when either Multi Link PPP or Single Link PPP is being unlocked.





References -

Table 170 transportMode (BTS transport mode) (Cont.)

Parameter name TWAMP initiator rate for sending messages

Abbreviated name twampMessageRate

3GPP name -

Managed Object IPNO

Multiplicity 1

Description This parameter specifies the overall rate at which the FTM sends TWAMP initiator messages. The messages are evenly spread over the enabled TWAMP sessions at any given time.

Range RATE_1 (0), RATE_10 (1)

Step -

Units -


gui ==> internal

RATE_1 ==> 0

RATE_10 ==> 1

Table 171 twampMessageRate (TWAMP initiator rate for sending messages)

228 DN70577885



IPNO Parameters

23.29 twampReflectorOn (TWAMP message response enabling flag)

Default value RATE_10 (1)


Related functions -




Related options -



References -

Table 171 twampMessageRate (TWAMP initiator rate for sending messages) (Cont.)

Parameter name TWAMP message response enabling flag

Abbreviated name twampReflectorOn

3GPP name -

Managed Object IPNO

Multiplicity 1

Description This parameter switches the TWAMP reflector on. The TWAMP reflector shall respond to each received measurement request packet from any sender. The TWAMP reflector re-uses the Sender Sequence Number, Sender Timestamp and Sender Error Estimate fields from the received packet in the response packet.


Step -

Units -


– false => 0 – true => 1


Default value notes By default the TWAMP reflector is switched on.

Table 172 twampReflectorOn (TWAMP message response enabling flag)

DN70577885 229



23.30 twampReflectorPort (TWAMP reflector port number)

Related functions -




Related options – RAN1900 IP Transport Network Measurement



References -

Table 172 twampReflectorOn (TWAMP message response enabling flag) (Cont.)

Parameter name TWAMP reflector port number

Abbreviated name twampReflectorPort

3GPP name -

Managed Object IPNO

Multiplicity 1

Description This parameter specifies the source port that is assigned to the TWAMP reflector. The sender on any measurement request packet shall use that port to reach the TWAMP reflector.

Range 1... 65535

Step 1

Units -



Default value 5000

Default value notes IANA-assigned well-known twamp-control port

Related functions -




Table 173 twampReflectorPort (TWAMP reflector port number)

230 DN70577885



IPNO Parameters

23.31 twampSourcePort (TWAMP source port number)




References -

Table 173 twampReflectorPort (TWAMP reflector port number) (Cont.)

Parameter name TWAMP source port number

Abbreviated name twampSourcePort

3GPP name -

Managed Object IPNO

Multiplicity 1

Description This parameter specifies the source port that is used in TWAMP initiator messages. The TWAMP port must be lower than the smallest port number used for regular traffic user plane connections of the FTM.

Range 1... 49151

Step 1

Units -



Default value 49151


Related functions -







Table 174 twampSourcePort (TWAMP source port number)

DN70577885 231



23.32 uPlane2IpAddress (Second user-plane application IP address)

References -

Table 174 twampSourcePort (TWAMP source port number) (Cont.)

Parameter name Second user-plane application IP address

Abbreviated name uPlane2IpAddress

3GPP name -

Managed Object IPNO

Multiplicity 1

Description This parameter specifies a 2nd IP address to be used for user-plane traffic by the FTM.

This IP address can collapse with the local IP address of the plain Ethernet interface (IEIF object) or with the local IP address of one of the VLAN interfaces (IVIF object) or with the local IP address of the ML-PPP interface (P3SL or P3ML object) of the FTM. If it does not collapse with such network interface IP address, the second user-plane IP address is virtual. In the latter case, the assignment to a network interface has to be configured addi-tionally by the operator.


Value 0.0.0.0 means the 2nd user-plane application IP address is not used at all.


Range 7...15

Step -

Units characters




Default value notes By default the second user-plane application IP address is not used.

Related functions -


Table 175 uPlane2IpAddress (Second user-plane application IP address)

232 DN70577885



IPNO Parameters

23.33 uPlane2IpInterface (Second user-plane application IP network interface)

Related parameters transportMode of IPNO - Parameter uPlane2IpAddress is irrelevant in case parameter transportMode has value AtmOverEthernet.

uPlane2IpInterface of IPNO - In case uPlane2IpAddress is a virtual IP address, the operator must configure parameter uPlane2IpInterface too.


Related options -



References -

Table 175 uPlane2IpAddress (Second user-plane application IP address) (Cont.)

Parameter name Second user-plane application IP network interface

Abbreviated name uPlane2IpInterface

3GPP name -

Managed Object IPNO

Multiplicity 1

Description This parameter maps the second user-plane IP address to an IP network interface if this IP address is a virtual IP address. This means: the FTM will use the second user-plane application IP address as source IP address in user-plane traffic sent over this interface.

Note that the interface of user-plane traffic is selected based on the entries of the static routing table of the FTM. If it happens to match the value of parameter uPlane2IpInterface, the IP address in parameter uPlane2IpAddress is used in user-plane traffic.

The format of this parameter is local managed object instance identifier (LMOID). The value refer-ences either the plain Ethernet interface (instance of IEIF object class) or a VLAN interface (instance of IVIF object class).

Table 176 uPlane2IpInterface (Second user-plane application IP network interface)

DN70577885 233



23.34 uPlaneIpAddress (User plane application IP address)

Range 0...40

Step -

Units characters



Default value -

Default value notes By default the parameter is empty: non-virtual IP addresses for the user-plane application are assumed, i.e. the uPlaneIpAddress collapses with the local IP address of either the plain Ethernet interface or one of the VLAN interfaces.

Related functions -


Related parameters uPlane2IpAddress of IPNO - Parameter uPlane2IpInterface must be configured in case parameter uPlane2IpAddress is a virtual IP address.


Related options -



References -

Table 176 uPlane2IpInterface (Second user-plane application IP network interface)

Parameter name User plane application IP address

Abbreviated name uPlaneIpAddress

3GPP name -

Managed Object IPNO

Multiplicity 1

Table 177 uPlaneIpAddress (User plane application IP address)

234 DN70577885



IPNO Parameters

Description This parameter specifies the IP address that is used for user plane traffic by the FTM.

This IP address can collapse with the local IP address of the plain Ethernet interface (IEIF object) or with the local IP address of one of the VLAN interfaces (IVIF object) or with the local IP address of the ML-PPP interface (P3SL or P3ML object) of the FTM. If it does not collapse with such network interface IP address, the second user-plane IP address is virtual. In the latter case, the assignment to a network interface has to be configured addi-tionally by the operator.


Value 0.0.0.0 means the user-plane application IP address is not used.


In case the second user-plane IP address is config-ured too, the operator has to additionally assign both the first and the 2nd user plane IP address to an IP network interface.

Range 7...15

Step -

Units characters




Default value notes By default the user-plane application IP address is not used.

Related functions -


Related parameters transportMode of IPNO - Parameter uPlaneIpAddress is irrelevant in case parameter transportMode has value AtmOverEthernet.

uPlaneIpInterface of IPNO - In case uPlane2IpAddress is a virtual IP address, the operator must configure parameter uPlaneIpInter-face too.


Related options -


Table 177 uPlaneIpAddress (User plane application IP address) (Cont.)

DN70577885 235



23.35 uPlaneIpInterface (User-plane application IP network interface)


References -

Table 177 uPlaneIpAddress (User plane application IP address) (Cont.)

Parameter name User-plane application IP network interface

Abbreviated name uPlaneIpInterface

3GPP name -

Managed Object IPNO

Multiplicity 1

Description This parameter maps the first user-plane IP address to an IP network interface if this IP address is a virtual IP address. This means: the FTM will use the first user-plane application IP address as source IP address in user-plane traffic sent over this interface.

Note that the interface of user-plane traffic is selected based on the entries of the static routing table of the FTM. If it happens to match the value of parameter uPlaneIpInterface, the IP address in parameter uPlaneIpAddress is used in user-plane traffic over that interface.

The format of this parameter is local managed object instance identifier (LMOID). The value refer-ences either the plain Ethernet interface (instance of IEIF object class) or a VLAN interface (instance of IVIF object class).

Range 0...40

Step -

Units characters



Default value -

Table 178 uPlaneIpInterface (User-plane application IP network interface)

236 DN70577885



IPNO Parameters

Default value notes By default the parameter is empty: non-virtual IP addresses for the user-plane application are assumed, i.e. the uPlaneIpAddress collapses with the local IP address of either the plain Ethernet interface or one of the VLAN interfaces.

Related functions -


Related parameters uPlaneIpAddress of IPNO - Parameter uPlaneIpInterface must be configured in case parameter uPlaneIpAddress and uPlane2IpAddress are virtual IP addresses.

uPlane2IpAddress of IPNO - Parameter uPlaneIpInterface must be configured in case parameter uPlaneIpAddress and uPlane2IpAddress are virtual IP addresses.


Related options -



References -

Table 178 uPlaneIpInterface (User-plane application IP network interface) (Cont.)

DN70577885 237

Flexi Transport Module Parameters IPRM Parameters


24 IPRM Parameters

24.1 RmExceptions (Restricted Mode Exception)

Parameter name Restricted Mode Exception

Abbreviated name RmExceptions

3GPP name -

Managed Object IPRM

Multiplicity 32

Description Restricted mode provides protection of the mobile carriers' network against intrusion through inter-faces of the Base Station, in particular the LMT. By default, all traffic to other destinations will be barred.

IPRM allows to configure exceptions, so that defined IP traffic will be allowed, for example com-munication with an LDAP server or administration of other base stations through the LMP of the local one.

Administration of the Restricted Mode consists therefore in defining exceptions from the general blocking of traffic to the outside world.

An RM exception is defined as a far end IP address to/from which traffic is allowed. Port information is not taken into account.

It is possible to define up to 32 exceptions.


-

Default value -


Related functions -

Child parameters – sourceTwoDiscr– sourceTwoIpAddr– sourceTwoNetMask– userLabel




Related options – RAN1749 BTS Firewall


Table 179 RmExceptions (Restricted Mode Exception)

238 DN70577885



IPRM Parameters

24.2 sourceTwoDiscr (How is source two defined?)


References -

Table 179 RmExceptions (Restricted Mode Exception) (Cont.)

Parameter name How is source two defined?

Abbreviated name sourceTwoDiscr

3GPP name -

Managed Object -

Multiplicity 1

Description With this parameter the user can select the way how to define source two.

Possible values are:

SINGLE: a single IP address

RANGE: a range of IP addresses given by an IP address and a subnet mask

WILDCARD: any IP adress is allowed

Range SINGLE (1), RANGE (2), WILDCARD (3)

Step -

Units -


gui ==> internal

SINGLE ==> 1

RANGE ==> 2

WILDCARD ==> 3

Default value SINGLE (1)


Related functions -






Table 180 sourceTwoDiscr (How is source two defined?)

DN70577885 239



24.3 sourceTwoIpAddr (IP address for source two)


References -

Table 180 sourceTwoDiscr (How is source two defined?) (Cont.)

Parameter name IP address for source two

Abbreviated name sourceTwoIpAddr

3GPP name -

Managed Object -

Multiplicity 1

Description This parameter is meaningful if and only if source two is defined as SINGLE or as RANGE; in all other cases it is ignored.

"IP address source two" specifies a single IP address.

If source two is defined as SINGLE, this is the only allowed IP address.

If source two is defined as RANGE, then the allowed range of IP addresses is obtained by applying the "IP subnet mask for source two" to this IP address.

The IP address must be given as "dotted decimal" string.

Range 7...15

Step -

Units characters





Related functions -


Related parameters sourceTwoDiscr of IPRM

Parameter relationships sourceTwoIpAddr is only relevant if parameter sourceTwoDiscr has value SINGLE or RANGE.

Table 181 sourceTwoIpAddr (IP address for source two)

240 DN70577885



IPRM Parameters

24.4 sourceTwoNetMask (IP Subnet Mask)




References -

Table 181 sourceTwoIpAddr (IP address for source two) (Cont.)

Parameter name IP Subnet Mask

Abbreviated name sourceTwoNetMask

3GPP name -

Managed Object -

Multiplicity 1

Description This parameter is meaningful if and only if source two is defined as RANGE; in all other cases it is ignored.

"IP Subnet Mask" specifies a netmask which, when applied to "IP address for source two" yields the allowed range of far end IP addresses.

The netmask must be entered in dotted decimal format.

Range 7...15

Step -

Units characters





Related functions -


Related parameters sourceTwoDiscr of IPRM

Parameter relationships SourceTwoNetmask is only meaningfull if parame-ter sourceTwoDiscr has value RANGE. Otherwise sourceTwoNetMask is ignored.



Table 182 sourceTwoNetMask (IP Subnet Mask)

DN70577885 241





References -

Table 182 sourceTwoNetMask (IP Subnet Mask) (Cont.)



3GPP name -

Managed Object -

Multiplicity 1

Description An alphanumeric string asigned by the user to uniquely identify the RM Exception.

(More exactly: only the pair userLabel/sourceOne must be unique)

Range 1...40

Step -

Units characters



Default value -


Related functions -







References -


242 DN70577885



IPRM Parameters

24.6 iprmId (IP Restricted Mode Identifier)

Parameter name IP Restricted Mode Identifier

Abbreviated name iprmId

3GPP name -

Managed Object IPRM

Multiplicity 1

Description This parameter identifies the firewall configuration of the BTS. The value is always 1.

Range 1... 1

Step 1

Units -



Default value -


Related functions -







References -

Table 184 iprmId (IP Restricted Mode Identifier)

DN70577885 243

Flexi Transport Module Parameters IPRT Parameters


25 IPRT Parameters

25.1 ipRoutingTableId (IP Routing Table Identifier)

Parameter name IP Routing Table Identifier

Abbreviated name ipRoutingTableId

3GPP name -

Managed Object IPRT

Multiplicity 1

Description This parameter identifies an IP routing table of the BTS.

Instance 1 shall only be used for DCN routing, instance 2 shall be used for IP routing. IPRT-1 is not supported in IubIP. "FTEB, FTHA, FTPB, FTFA, FTFB, FTIF and FIIF" are not supported for IPRT-2 in AtmIub mode. "FSM and FSI" are supported for IPRT-2 only in IubIP mode.

Range 1... 2

Step 1

Units -



Default value -


Related functions -


Related parameters transportMode of IPNO - An instance for IP routing shall only be available in transport mode Iub/IP.

iHSPAmode of IPNO - If iHS-PAmode is set to enabled, then only IPRT-2(ipRou-tingTableId=2) is supported.


Related options -

Feature dependencies – IPv4 routing for management traffic, DHCP, NTP


Table 185 ipRoutingTableId (IP Routing Table Identifier)

244 DN70577885



IPRT Parameters

25.2 staticRoutes (List of static routes)

25.3 bfdId (BFD route protection session identifier)

References -

Table 185 ipRoutingTableId (IP Routing Table Identifier) (Cont.)

Parameter name List of static routes

Abbreviated name staticRoutes

3GPP name -

Managed Object IPRT

Multiplicity 32

Description Contains the list of static (configured) routes.


-

Default value -


Related functions -

Child parameters – bfdId– destIpAddr– gateway– netmask– preference




Related options -



References -

Table 186 staticRoutes (List of static routes)

Parameter name BFD route protection session identifier

Abbreviated name bfdId

Table 187 bfdId (BFD route protection session identifier)

DN70577885 245



25.4 destIpAddr (Route destination IP address)

3GPP name -

Managed Object -

Multiplicity 1

Description This parameter identifies the Bidirectional Forward-ing Detection (BFD) session that shall protect this route. The parameter value shall match one of the object instance identifiers of the BFD managed object class.

Value 0 means the route is not protected by any BFD session.

Range 0... 16

Step 1

Units -



Default value 0

Default value notes The route is not protected.

Related functions -







References -

Table 187 bfdId (BFD route protection session identifier) (Cont.)

Parameter name Route destination IP address

Abbreviated name destIpAddr

3GPP name -

Managed Object -

Multiplicity 1

Table 188 destIpAddr (Route destination IP address)

246 DN70577885



IPRT Parameters

25.5 gateway (IP address of the next hop of the route)

Description Specifies the IP address for indirectly connected (point-to-point) IP nodes (remote network). If a default gateway shall be defined, the value is to be set to 0.0.0.0.

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 188 destIpAddr (Route destination IP address) (Cont.)

Parameter name IP address of the next hop of the route

Abbreviated name gateway

3GPP name -

Managed Object -

Multiplicity 1

Description Specifies the IP address of the next hop via which the route destination Ip address can be reached.

Range 7...15

Step -

Units characters

Table 189 gateway (IP address of the next hop of the route)

DN70577885 247



25.6 netmask (Netmask of the destination IP address)



Default value -


Related functions -




Related options -



References -

Table 189 gateway (IP address of the next hop of the route) (Cont.)

Parameter name Netmask of the destination IP address


3GPP name -

Managed Object -

Multiplicity 1

Description Specifies the subnet mask of the route destination IP address. If a default gateway shall be defined, the value is to be set to 0.0.0.0.

Range 7...15

Step -

Units characters



Default value -


Related functions -



Table 190 netmask (Netmask of the destination IP address)

248 DN70577885



IPRT Parameters

25.7 preference (Preference value for the route)


Related options -



References -

Table 190 netmask (Netmask of the destination IP address) (Cont.)

Parameter name Preference value for the route

Abbreviated name preference

3GPP name -

Managed Object -

Multiplicity 1

Description This parameter specifies a preference value for this route. The FTM shall use by preference routes with lower preference value.

Range 1... 254

Step 1

Units -



Default value 1

Default value notes Default value is lowest possible preference value. By default all routes have equally low cost.

Related functions -






Table 191 preference (Preference value for the route)

DN70577885 249




References -

Table 191 preference (Preference value for the route) (Cont.)

250 DN70577885



IVIF Parameters

26 IVIF Parameters

26.1 cESoPSN (CES over PSN flag)

Parameter name CES over PSN flag

Abbreviated name cESoPSN

3GPP name -

Managed Object IVIF

Multiplicity 1

Description This flag specifies if this interface shall be used for CES over PSN. If true, the traffic over this interface will not be shaped.

Beware that still the actual interface that is used for CES over PSN packets is decided via dynamic routing based on the entries of the static routing table of managed object class IPRT.


Step -

Units -


– false => 0 – true => 1



Related functions -







References -

Table 192 cESoPSN (CES over PSN flag)

DN70577885 251

Flexi Transport Module Parameters IVIF Parameters


26.2 cir (Committed information rate)

Parameter name Committed information rate

Abbreviated name cir

3GPP name -

Managed Object IVIF

Multiplicity 1

Description The VLAN Committed Information Rate ("VLAN CIR") shall define the average rate up to which traffic is delivered by one VLAN. It shall define the guaranteed transport capacity for the VLAN. The parameter is required for dynamic CAC.


If there are several IP interfaces and shaping is PATH, Connection Admission Control is based on CIR parameter of the IP interface that user plane uses.

Range 0... 1000000

Step 100

Units kbps



Default value 0


Related functions -







References -

Table 193 cir (Committed information rate)

252 DN70577885



IVIF Parameters

26.3 confCost (OSPF configured interface cost)

26.4 helloInterval (OSPF keepalive message transmission interval)

Parameter name OSPF configured interface cost

Abbreviated name confCost

3GPP name -

Managed Object IVIF

Multiplicity 1

Description This parameter specifies the cost used by the inter-face as defined by the operator. Value 0 means "not specified": If OSPF is enabled the cost calculated by the OSPF router shall be used instead.

Range 0... 65535

Step 1

Units -



Default value 0

Default value notes Default means: "not specified by the operator, use OSPF router calculated cost instead".

Related functions -







References -

Table 194 confCost (OSPF configured interface cost)

Parameter name OSPF keepalive message transmission interval

Abbreviated name helloInterval

Table 195 helloInterval (OSPF keepalive message transmission interval)

DN70577885 253



26.5 interfaceArea (OSPF interface area)

3GPP name -

Managed Object IVIF

Multiplicity 1

Description This parameter specifies the interval for transmit-ting keepalive ("Hello") messages.

Range 1... 65535

Step 1

Units -



Default value 1


Related functions -


Related parameters routerDeadInterval of IVIF - Router dead interval should be greater than hello interval


Related options -



References -

Table 195 helloInterval (OSPF keepalive message transmission interval) (Cont.)

Parameter name OSPF interface area

Abbreviated name interfaceArea

3GPP name -

Managed Object IVIF

Multiplicity 1

Description This parameter specifies the OSPF area to which the interface belongs.

Range 0...15

Step -

Table 196 interfaceArea (OSPF interface area)

254 DN70577885



IVIF Parameters

26.6 localIpAddr (Local Address of the IP Interface)

Units characters



Default value -

Default value notes Empty value means OSPF is disabled on this inter-face.

Related functions -







References -

Table 196 interfaceArea (OSPF interface area) (Cont.)

Parameter name Local Address of the IP Interface

Abbreviated name localIpAddr

3GPP name -

Managed Object IVIF

Multiplicity 1

Description This parameter holds the IP address of the BTS in the transport network for this VLAN. It is accompa-nied with a subnet mask.

Range 7...15

Step -

Units characters



Default value -


Table 197 localIpAddr (Local Address of the IP Interface)

DN70577885 255



26.7 mtuMismatchDetection (MTU mismatch detection in use)

Related functions -







References NSN reference: WBTS_TRS_4548

Table 197 localIpAddr (Local Address of the IP Interface) (Cont.)

Parameter name MTU mismatch detection in use

Abbreviated name mtuMismatchDetection

3GPP name -

Managed Object IVIF

Multiplicity 1

Description If set to true, this parameter enables OSPF MTU mismatch detection on receiving DBD (Data Base Descriptor) packets on this interface.


Step -

Units -


– false => 0 – true => 1



Related functions -






Table 198 mtuMismatchDetection (MTU mismatch detection in use)

256 DN70577885



IVIF Parameters

26.8 netmask (IP network mask of the local IP address)


References -

Table 198 mtuMismatchDetection (MTU mismatch detection in use) (Cont.)

Parameter name IP network mask of the local IP address


3GPP name -

Managed Object IVIF

Multiplicity 1

Description This parameter holds the network mask for the IP address of the BTS in the transport network for this VLAN.

Range 7...15

Step -

Units characters



Default value -


Related functions -







References -

Table 199 netmask (IP network mask of the local IP address)

DN70577885 257



26.9 ospfWithBfd (OSPF uses additionally BFD)

26.10 proxyArpIpAddrList (List of proxy ARP IP addresses for this interface.)

Parameter name OSPF uses additionally BFD

Abbreviated name ospfWithBfd

3GPP name -

Managed Object IVIF

Multiplicity 1

Description If set to true the OSPF router shall use Bidirectional Forwarding Detection (BFD) for detecting link inter-ruptions on this interface. If set to false, the OSPF router only uses keepalive Hello messages.


Step -

Units -


– false => 0 – true => 1


Default value notes The OSPF router does not use BFD but only Hello messages.

Related functions -


Related parameters iHSPAmode of IPNO - In iHS-PAmode only ManualBfdSession is supported.


Related options – RAN2359 OSPF enhancements



References -

Table 200 ospfWithBfd (OSPF uses additionally BFD)

Parameter name List of proxy ARP IP addresses for this interface.

Abbreviated name proxyArpIpAddrList


258 DN70577885



IVIF Parameters

26.11 qosEnabled (QOS traffic priorisation enabling flag)

3GPP name -

Managed Object IVIF

Multiplicity 16

Description This parameter holds a list of up to 16 IP addresses that can be used for proxy ARP detection.

The format of each IP address in the list is dotted decimal.

An empty list means the feature is not used.

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -

Feature dependencies – RAN2083 ProxyARP in BTS


References -


Parameter name QOS traffic priorisation enabling flag

Abbreviated name qosEnabled

3GPP name -

Managed Object IVIF

Multiplicity 1

Table 202 qosEnabled (QOS traffic priorisation enabling flag)

DN70577885 259



26.12 retransInterval (OSPF LSA retransmission interval)

Description This parameter specifies if multiple queues are used over this interface or only a single one. Multiple queues allow DSCP based traffic priorisa-tion.

Amongst the active interfaces (IEIF or IVIF managed object instances) there shall be at least one and at most 2 interfaces carrying a multiple queue scheduler. So qosEnabled shall have value true for at least one interface and must not have value true on more than 2 interfaces.


Step -

Units -


– false => 0 – true => 1


Default value notes By default the 6 PHB qeueue scheduler is not installed on a VLAN interface.

Related functions -







References -

Table 202 qosEnabled (QOS traffic priorisation enabling flag) (Cont.)

Parameter name OSPF LSA retransmission interval

Abbreviated name retransInterval

3GPP name -

Managed Object IVIF

Multiplicity 1

Table 203 retransInterval (OSPF LSA retransmission interval)

260 DN70577885



IVIF Parameters

26.13 routerDeadInterval (OSPF router read interval)

Description This parameter specifies the value for the retrans-mission of Link State Advertisement (LSA) messages for OSPF. Currently values of 1s and 2s are not supported for LSA retransmission interval .

This issue is to be resolved in the future release of the software.

Range 1... 65535

Step 1

Units -



Default value 5


Related functions -







References -

Table 203 retransInterval (OSPF LSA retransmission interval) (Cont.)

Parameter name OSPF router read interval

Abbreviated name routerDeadInterval

3GPP name -

Managed Object IVIF

Multiplicity 1

Description This parameter specifies the value for OSPF router dead interval in seconds. If no hello packet is received within the router dead interval, the link is assumed to be down.

Table 204 routerDeadInterval (OSPF router read interval)

DN70577885 261



26.14 sbs (Shaper burst size)

Range 1... 65535

Step 1

Units -



Default value 4


Related functions -



helloInterval of IVIF - Router dead interval should be greater than hello interval





References -

Table 204 routerDeadInterval (OSPF router read interval) (Cont.)

Parameter name Shaper burst size

Abbreviated name sbs

3GPP name -

Managed Object IVIF

Multiplicity 1

Description The Traffic Path Shaper Burst Size (SBS) shall define the maximum burst size that is allowed to pass the traffic path shaper.

Range 1522... 2000000

Step 1

Units octets

Table 205 sbs (Shaper burst size)

262 DN70577885



IVIF Parameters

26.15 sir (Shaper information rate)



Default value 1522


Related functions -







References -

Table 205 sbs (Shaper burst size) (Cont.)

Parameter name Shaper information rate

Abbreviated name sir

3GPP name -

Managed Object IVIF

Multiplicity 1

Description The Shaper Information Rate ("VLAN SIR") defines the bandwidth limit to which VLAN traffic is shaped by the traffic path shaper.

Note: The SIRs should be configured to equal the sum of CIR+EIR at the corresponding UNI.

The sum of all SIRs is allowed to exceed the total available bandwidth on the interface (overbooking). Therefore, SIR cannot be guaranteed by the system.

Range 0... 1000000

Step 100

Units kbps




Table 206 sir (Shaper information rate)

DN70577885 263



26.16 transmitDelay (OSPF packet transmission delay)


Related functions -







References -

Table 206 sir (Shaper information rate) (Cont.)

Parameter name OSPF packet transmission delay

Abbreviated name transmitDelay

3GPP name -

Managed Object IVIF

Multiplicity 1

Description This parameter specifies the OSPF transmit delay. This is the amount of time added to the age of an OSPF Link State Update (LSU) packet before transmitting it. It is the estimated number of seconds to transmit a packet over the interface.

Range 1... 65535

Step 1

Units -



Default value 1


Related functions -



Table 207 transmitDelay (OSPF packet transmission delay)

264 DN70577885



IVIF Parameters

26.17 vlanId (VLAN identifier)





References -

Table 207 transmitDelay (OSPF packet transmission delay) (Cont.)

Parameter name VLAN identifier


3GPP name -

Managed Object IVIF

Multiplicity 1

Description This parameter holds the VLAN identifier number.

Range 0... 4094

Step 1

Units -



Default value -


Related functions -







References -

Table 208 vlanId (VLAN identifier)

DN70577885 265



26.18 vlanIfNetId (VLAN interface object identifier)

Parameter name VLAN interface object identifier

Abbreviated name vlanIfNetId

3GPP name -

Managed Object IVIF

Multiplicity 1

Description This parameter identifies the VLAN interface object. Value range is 1 to 7.

Up to 6 VLANs may exist in IP Iub mode. Up to 5 VLANs may exist in Dual Iub mode.

One of the VLAN interfaces is intended to be reserved for FlexiPacket Radio Management.

One of the VLAN interfaces is intended to be reserved for CES over PSN.

Range 1... 7

Step 1

Units -



Default value -


Related functions -




Related options – RAN1709 VLAN Traffic Differentiation– RAN1883 FlexiPacket Radio Management



References -

Table 209 vlanIfNetId (VLAN interface object identifier)

266 DN70577885



L2SWI Parameters

27 L2SWI Parameters

27.1 dscpMap (DSCP to priority queue map)

Parameter name DSCP to priority queue map

Abbreviated name dscpMap

3GPP name -

Managed Object L2SWI

Multiplicity 64

Description This parameter maps DSCP values to priority queues. The table contains at most 64 entries, one for each possible DSCP value (0..63).

Default values for non-FTLB hardware unit type:

DSCP values 48 and 46 map to priority queue 1, this is the strict priority queue.

DSCP values 38, 36, 34, 30, 28 and 26 map to priority queue 2, this is the first WRR priority queue.

DSCP values 22, 20, 18, 14, 12 and 10 map to priority queue 3, this is the second WRR priority queue.

All other DSCP values map by default to priority queue 4, this is the third WRR priority queue.

Default values for FTLB & FSMr3 hardware unit type:

DSCP values 48 and 46 map to priority queue 1, this is the strict priority queue.

DSCP values 38, 36 and 34 map to priority queue 2, this is the first WRR priority queue.

DSCP values 30, 28 and 26 map to priority queue 3, this is the second WRR priority queue.

DSCP values 22, 20, 18, 14, 12 and 10 map to priority queue 4, this is the third WRR priority queue.

All other DSCP values map by default to priority queue 6, this is the fifth WRR priority queue.


-

Default value -


Related functions -

Table 210 dscpMap (DSCP to priority queue map)

DN70577885 267

Flexi Transport Module Parameters L2SWI Parameters


27.2 dscp (DSCP value)

Child parameters – dscp– priorityQueue








Table 210 dscpMap (DSCP to priority queue map) (Cont.)

Parameter name DSCP value


3GPP name -

Managed Object -

Multiplicity 1

Description This parameter specifies a DSCP value.

Range 0... 63

Step 1

Units -



Default value -


Related functions -




Table 211 dscp (DSCP value)

268 DN70577885



L2SWI Parameters

27.3 priorityQueue (Priority queue identifier)




References -

Table 211 dscp (DSCP value) (Cont.)

Parameter name Priority queue identifier

Abbreviated name priorityQueue

3GPP name -

Managed Object -

Multiplicity 1

Description This parameter specifies a priority queue.

Non-FTLB hardware unit type:

Priority queue values range from 1 to 4 where 4 means lowest and 1 means highest priority. The default value of the parameter = 4.

FTLB & FSMr3 hardware unit type:

Priority queue values range from 1 to 6 where 6 means lowest and 1 means highest priority. The default value of the parameter = 6.

Range 1... 6

Step 1

Units -



Default value 4


Related functions -




Table 212 priorityQueue (Priority queue identifier)

DN70577885 269



27.4 enableLayer2Switching (Ethernet Switch Enable)





Table 212 priorityQueue (Priority queue identifier) (Cont.)

Parameter name Ethernet Switch Enable

Abbreviated name enableLayer2Switching

3GPP name -


Multiplicity 1

Description This parameter indicates if the ethernet link is par-ticipating in the QOS aware layer 2 switch.


Step -

Units -


– false => 0 – true => 1


Default value notes "false" means the switching is "MAC_ADDRESS" based

Related functions -







Table 213 enableLayer2Switching (Ethernet Switch Enable)

270 DN70577885



L2SWI Parameters

27.5 l2PriorityQueueWeight2 (Layer 2 switch member weight for priority queue 2)

References -

Table 213 enableLayer2Switching (Ethernet Switch Enable) (Cont.)

Parameter name Layer 2 switch member weight for priority queue 2

Abbreviated name l2PriorityQueueWeight2

3GPP name -


Multiplicity 1

Description This parameter specifies the weight for the 1st priority queue.

Range 1... 8

Step 1

Units -



Default value 8


Related functions -








Table 214 l2PriorityQueueWeight2 (Layer 2 switch member weight for priority queue 2)

DN70577885 271






3GPP name -


Multiplicity 1

Description This parameter specifies the weight for the second priority queue.

The default value of this parameter = 1 for the FTIB hardware unit.

The default value of this parameter = 4 for the FTLB hardware unit.

Range 1... 8

Step 1

Units -



Default value -

Default value notes The default value of this parameter = 1 for the FTIB hardware unit.The default value of this parameter = 4 for the FTLB hardware unit.

Related functions -









272 DN70577885



L2SWI Parameters





3GPP name -


Multiplicity 1

Description This parameter specifies the weight for the third priority queue.

Range 1... 8

Step 1

Units -



Default value 1


Related functions -











DN70577885 273





3GPP name -


Multiplicity 1

Description This parameter specifies the weight for the fourth priority queue.

This parameter is only supported for the FTLB hardware unit.

Range 1... 8

Step 1

Units -



Default value 1


Related functions -








Table 217 l2PriorityQueueWeight5 (Layer 2 switch member weight for priority queue 5) (Cont.)



3GPP name -


274 DN70577885



L2SWI Parameters

27.10 portDefaultPriority (Switch Port Default VLAN Priority (internal Port))


Multiplicity 1

Description This parameter specifies the weight for the fifth priority queue.

This parameter is only supported for the FTLB hardware unit.

Range 1... 8

Step 1

Units -



Default value 1


Related functions -








Table 218 l2PriorityQueueWeight6 (Layer 2 switch member weight for priority queue 6) (Cont.)

Parameter name Switch Port Default VLAN Priority (internal Port)

Abbreviated name portDefaultPriority

3GPP name -


Multiplicity 1

Table 219 portDefaultPriority (Switch Port Default VLAN Priority (internal Port))

DN70577885 275



27.11 portDefaultVlanId (Switch Port Default VLAN Identifier (internal Port))

Description Default VLAN priority for untagged frames.

Every untagged ingress Ethernet frame at this inter-face gets assigned this Port Default Priority. If QoS classification mode is configured to VLAN-PCP, this priority is used for enqueing decision of the frame. If the frame egresses the switch tagged, this priority shall be used in the VLAN tag header.

Range 0... 7

Step 1

Units -



Default value 0


Related functions -


Related parameters enableLayer2Switching of L2SWI - VLAN aware switching mode should be enabled (enableLayer2Switching="true")






Table 219 portDefaultPriority (Switch Port Default VLAN Priority (internal Port))

Parameter name Switch Port Default VLAN Identifier (internal Port)

Abbreviated name portDefaultVlanId

3GPP name -


Multiplicity 1

Table 220 portDefaultVlanId (Switch Port Default VLAN Identifier (internal Port))

276 DN70577885



L2SWI Parameters

27.12 priorityQueueNonIP (Priority queue for non-IP frames)

Description This parameter specifies the VLAN identifier that is inserted internally by the FTM into an untagged ingress frame that enters the layer 2 switch via this Ethernet interface - if parameter discardUntagged has value false for the Ethernet interface.

In order that the frame will be transmitted via the same or another Ethernet interface, after layer 2 switching has been performed, the same VLAN id must be configured in the VLAN identifier list of that Ethernet interface (see parameter l2VlanIdList). Else the frame will be discarded.

Range 1... 4094

Step 1

Units -



Default value 1

Default value notes Default VLAN id = 1.

Related functions -


Related parameters enableLayer2Switching of L2SWI - VLAN aware switching mode should be enabled (enableLayer2Switching="true")






Table 220 portDefaultVlanId (Switch Port Default VLAN Identifier (internal Port))

Parameter name Priority queue for non-IP frames

Abbreviated name priorityQueueNonIP

3GPP name -


Table 221 priorityQueueNonIP (Priority queue for non-IP frames)

DN70577885 277



27.13 priorityQueuePcp0 (Priority queue for ethernet frames with VLAN PCP bits 0)

Multiplicity 1

Description This parameter specifies which priority queue shall be used for non-IP frames. Non-IP frames examples are ARP-, Ethernet OAM- and Synchro-nous Ethernet messages. The range is

1-6 for FTLB, FSMr3 and

1-4 for all others.

Range 1... 6

Step 1

Units -



Default value 1

Default value notes The default queue is the strict priority queue. By default non-IP traffic is handled with high priority.

Related functions -








Table 221 priorityQueueNonIP (Priority queue for non-IP frames) (Cont.)

Parameter name Priority queue for ethernet frames with VLAN PCP bits 0

Abbreviated name priorityQueuePcp0

3GPP name -

Table 222 priorityQueuePcp0 (Priority queue for ethernet frames with VLAN PCP bits 0)

278 DN70577885



L2SWI Parameters



Multiplicity 1

Description This parameter specifies which priority queue shall be used for ethernet frames with VLAN PCP bits value 0.

The range is


1-4 for all others.

Range 1... 6

Step 1

Units -



Default value 4

Default value notes The default queue is a Weighted Round Robin priority queue. Default value is 4 for non-FTLB and 6 for FTLB.

Related functions -








Table 222 priorityQueuePcp0 (Priority queue for ethernet frames with VLAN PCP bits 0) (Cont.)



DN70577885 279




3GPP name -


Multiplicity 1


The range is


1-4 for all others.

Range 1... 6

Step 1

Units -



Default value 4

Default value notes The default queue is a Weighted Round Robin priority queue.

Related functions -








Table 223 priorityQueuePcp1 (Priority queue for ethernet frames with VLAN PCP bits 1) (Cont.)

280 DN70577885



L2SWI Parameters




3GPP name -


Multiplicity 1


The range is


1-4 for all others.

Range 1... 6

Step 1

Units -



Default value 3


Related functions -









DN70577885 281






3GPP name -


Multiplicity 1


The range is


1-4 for all others.

Range 1... 6

Step 1

Units -



Default value 3


Related functions -









282 DN70577885



L2SWI Parameters




3GPP name -


Multiplicity 1


The range is


1-4 for all others.

Range 1... 6

Step 1

Units -



Default value 2


Related functions -









DN70577885 283






3GPP name -


Multiplicity 1


The range is


1-4 for all others.

Range 1... 6

Step 1

Units -



Default value 2


Related functions -









284 DN70577885



L2SWI Parameters




3GPP name -


Multiplicity 1


The range is


1-4 for all others.

Range 1... 6

Step 1

Units -



Default value 1

Default value notes The default queue is the strict priority queue. Default value is 1 for non-FTLB and 2 for FTLB.

Related functions -







References -


DN70577885 285






3GPP name -


Multiplicity 1


The range is


1-4 for all others.

Range 1... 6

Step 1

Units -



Default value 1

Default value notes The default queue is the strict priority queue.

Related functions -









286 DN70577885



L2SWI Parameters

27.21 priorityQueueUntagged (Priority queue for untagged ethernet frames)

Parameter name Priority queue for untagged ethernet frames

Abbreviated name priorityQueueUntagged

3GPP name -


Multiplicity 1

Description This parameter specifies which priority queue shall be used for untagged ethernet frames.

The range is


1-4 for all others.

Range 1... 6

Step 1

Units -



Default value 1

Default value notes The default queue is the strict priority queue. By default untagged ethernet frames are handled with high priority.

Related functions -








Table 230 priorityQueueUntagged (Priority queue for untagged ethernet frames)

DN70577885 287



27.22 qosClassification (QoS Classification Mode)

27.23 switchId (Layer 2 Switch Object Identifier)

Parameter name QoS Classification Mode

Abbreviated name qosClassification

3GPP name -


Multiplicity 1

Description This parameter specifies if the QOS aware switch-ing is based on DSCP to PHB mapping or on PCP to PHB mapping.

Range DSCP (0), PCP (1)

Step -

Units -


gui ==> internal

DSCP ==> 0

PCP ==> 1

Default value DSCP (0)

Default value notes Default value means DSCP to PHB mapping.

Related functions -







References -

Table 231 qosClassification (QoS Classification Mode)

Parameter name Layer 2 Switch Object Identifier

Abbreviated name switchId

3GPP name -

Table 232 switchId (Layer 2 Switch Object Identifier)

288 DN70577885



L2SWI Parameters

27.24 vlanAwareSwitch (VLAN Aware Switching Enable)


Multiplicity 1

Description This parameter identifies the BTS transport layer 2 switch. The value is always 1.

Range 1... 1

Step 1

Units -



Default value -


Related functions -







References -

Table 232 switchId (Layer 2 Switch Object Identifier) (Cont.)

Parameter name VLAN Aware Switching Enable

Abbreviated name vlanAwareSwitch

3GPP name -


Multiplicity 1

Description This parameter specifies if VLAN information shall be taken into account at the layer 2 switch. By default VLAN information is not taken into account: switching is only based on MAC destination address lookup.


Table 233 vlanAwareSwitch (VLAN Aware Switching Enable)

DN70577885 289



Step -

Units -


– false => 0 – true => 1


Default value notes Default value is not to include VLAN information in the switching decision.

Related functions -







References -

Table 233 vlanAwareSwitch (VLAN Aware Switching Enable) (Cont.)

290 DN70577885



OAMMA Parameters

28 OAMMA Parameters

28.1 assocId (Maintenance association identifier)

28.2 maName (Name of the maintenance domain)

Parameter name Maintenance association identifier

Abbreviated name assocId

3GPP name -

Managed Object OAMMA

Multiplicity 1

Description This parameter identifies an Ethernet service OAM maintenance association. Up to 15 associations may exist in the BTS.

Range 1... 15

Step 1

Units -



Default value -


Related functions -







References -

Table 234 assocId (Maintenance association identifier)

Parameter name Name of the maintenance domain

Table 235 maName (Name of the maintenance domain)

DN70577885 291

Flexi Transport Module Parameters OAMMA Parameters


28.3 vlanId (VLAN identifier of the maintenance association)

Abbreviated name maName

3GPP name -


Multiplicity 1

Description This parameter specifies the name of the Mainte-nance Association.

Range 1...42

Step -

Units characters



Default value -


Related functions -







References -

Table 235 maName (Name of the maintenance domain) (Cont.)

Parameter name VLAN identifier of the maintenance association


3GPP name -


Multiplicity 1

Table 236 vlanId (VLAN identifier of the maintenance association)

292 DN70577885



OAMMA Parameters

Description This parameter specifies the VLAN identifier that is associated to the Maintenance Association.

The FTM uses this VLAN identifier in the Service OAM messages its sends over the Service OAM ethernet link (configured in the OAMMEP managed object).

Note: The configured VLAN identifier must match the restrictions of the VLAN identifier settings of the Layer 2 bridges of the FTM, in order to prevent that the Service OAM messages are discarded in the bridge.

Range 0... 4094

Step 1

Units -



Default value 0

Default value notes Parameter vlanId = 0 means the maintenance association is not associated to any VLAN.

Related functions -







References -

Table 236 vlanId (VLAN identifier of the maintenance association) (Cont.)

DN70577885 293

Flexi Transport Module Parameters OAMMD Parameters


29 OAMMD Parameters

29.1 domainId (Maintenance domain identifier)

29.2 mdLevel (Level of the maintenance domain)

Parameter name Maintenance domain identifier

Abbreviated name domainId

3GPP name -

Managed Object OAMMD

Multiplicity 1

Description This parameter identifies an Ethernet service OAM maintenance domain. Up to 10 domains may exist on the BTS.

Range 1... 10

Step 1

Units -



Default value -


Related functions -







References -

Table 237 domainId (Maintenance domain identifier)

Parameter name Level of the maintenance domain

Table 238 mdLevel (Level of the maintenance domain)

294 DN70577885



OAMMD Parameters

29.3 mdName (Name of the maintenance domain)

Abbreviated name mdLevel

3GPP name -


Multiplicity 1

Description This parameter specifies the level of the Mainte-nance Domain.

Range 0... 7

Step 1

Units -



Default value -


Related functions -







References -

Table 238 mdLevel (Level of the maintenance domain) (Cont.)

Parameter name Name of the maintenance domain

Abbreviated name mdName

3GPP name -


Multiplicity 1

Description This parameter specifies the name of the Mainte-nance Domain.

Table 239 mdName (Name of the maintenance domain)

DN70577885 295

Flexi Transport Module Parameters OAMMD Parameters


Range 1...42

Step -

Units characters



Default value -


Related functions -







References -

Table 239 mdName (Name of the maintenance domain) (Cont.)

296 DN70577885



OAMMEP Parameters

30 OAMMEP Parameters

30.1 aisEnabled (AIS message transmission enabling flag)

30.2 aisTxPeriod (AIS messages transmission period)

Parameter name AIS message transmission enabling flag

Abbreviated name aisEnabled

3GPP name -

Managed Object OAMMEP

Multiplicity 1

Description This parameter specifies if the transmission of AIS messages is enabled.


Step -

Units -


– false => 0 – true => 1



Related functions -




Related options -



References -

Table 240 aisEnabled (AIS message transmission enabling flag)

Parameter name AIS messages transmission period

Abbreviated name aisTxPeriod

Table 241 aisTxPeriod (AIS messages transmission period)

DN70577885 297

Flexi Transport Module Parameters OAMMEP Parameters


30.3 ccmTxPeriod (Continuity Check Messages transmission period)

3GPP name -


Multiplicity 1

Description This parameter specifies the rate for sending AIS messages.

Range AIS_1SEC (0), AIS_1MIN (1)

Step -

Units -


gui ==> internal

AIS_1SEC ==> 0

AIS_1MIN ==> 1

Default value AIS_1SEC (0)


Related functions -




Related options -



References -

Table 241 aisTxPeriod (AIS messages transmission period) (Cont.)

Parameter name Continuity Check Messages transmission period

Abbreviated name ccmTxPeriod

3GPP name -


Multiplicity 1

Description This parameter specifies the period for sending Continuity Check messages (CCMs).

Table 242 ccmTxPeriod (Continuity Check Messages transmission period)

298 DN70577885



OAMMEP Parameters

30.4 enableCcm (Allow sending of CCM messages and reset CCM counters)

Range CCM_3_33MS (0), CCM_10MS (1), CCM_100MS (2), CCM_1SEC (3), CCM_10SEC (4), CCM_1MIN (5), CCM_10MIN (6)

Step -

Units -


gui ==> internal

CCM_3_33MS ==> 0

CCM_10MS ==> 1

CCM_100MS ==> 2

CCM_1SEC ==> 3

CCM_10SEC ==> 4

CCM_1MIN ==> 5

CCM_10MIN ==> 6

Default value CCM_1SEC (3)


Related functions -







References -

Table 242 ccmTxPeriod (Continuity Check Messages transmission period) (Cont.)

Parameter name Allow sending of CCM messages and reset CCM counters

Abbreviated name enableCcm

3GPP name -

Table 243 enableCcm (Allow sending of CCM messages and reset CCM counters)

DN70577885 299



30.5 ethernetPort (Ethernet link reference)


Multiplicity 1

Description This parameter allows sending continuity check messages (ETH_CCM) towards the remote Mainte-nance Association Endpoints (MEPs) of the End Point. Changeing the parameter from false (not allowed) to true (allowed) resets the CCM counters of all remote MEPs.


Step -

Units -


– false => 0 – true => 1


Default value notes By default, sending CCM messages is not allowed.

Related functions -







References -


Parameter name Ethernet link reference

Abbreviated name ethernetPort

3GPP name -


Multiplicity 1

Table 244 ethernetPort (Ethernet link reference)

300 DN70577885



OAMMEP Parameters

30.6 oammepId (Maintenance association endpoint identifier)

Description This parameter specifies the ethernet link that the FTM shall use for sending Service OAM messages. The parameter is a local managed object instance identifier (LMOID), i.e. a reference to an instance of object class ETHLK. ethernetport cannot be set to FB bit pipe interface.

Range 0...40

Step -

Units characters



Default value -


Related functions -







References -

Table 244 ethernetPort (Ethernet link reference) (Cont.)

Parameter name Maintenance association endpoint identifier

Abbreviated name oammepId

3GPP name -


Multiplicity 1

Description This parameter identifies an Ethernet service OAM maintenance association endpoint (MEP).

Range 1... 8191

Table 245 oammepId (Maintenance association endpoint identifier)

DN70577885 301



30.7 remoteMepList (Remote maintenance association end-points list)

Step 1

Units -



Default value -


Related functions -







References -

Table 245 oammepId (Maintenance association endpoint identifier) (Cont.)

Parameter name Remote maintenance association endpoints list

Abbreviated name remoteMepList

3GPP name -


Multiplicity 30

Description This parameter specifies the list of Maintenance Association Endpoints (MEPs) that are contained in the Maintenance Association.


-

Default value -


Related functions -

Table 246 remoteMepList (Remote maintenance association endpoints list)

302 DN70577885



OAMMEP Parameters

30.8 macAddr (MAC address of the remote MEP)

Child parameters – macAddr– mepId







References -

Table 246 remoteMepList (Remote maintenance association endpoints list) (Cont.)

Parameter name MAC address of the remote MEP

Abbreviated name macAddr

3GPP name -

Managed Object -

Multiplicity 1

Description This parameter specifies the MAC address of the remote Maintenance Association End Point (MEP).

Range 17

Step -

Units characters



Default value -


Related functions -



Table 247 macAddr (MAC address of the remote MEP)

DN70577885 303



30.9 mepId (Remote maintenance association endpoint identi-fier)





References -

Table 247 macAddr (MAC address of the remote MEP) (Cont.)

Parameter name Remote maintenance association endpoint identi-fier

Abbreviated name mepId

3GPP name -

Managed Object -

Multiplicity 1

Description This parameter specifies the identifier of the remote Maintenance Association End Point (MEP).

Range 1... 8191

Step 1

Units -



Default value -


Related functions -






Table 248 mepId (Remote maintenance association endpoint identifier)

304 DN70577885



OAMMEP Parameters

30.10 vlanPrio (VLAN PCP bits)


References -

Table 248 mepId (Remote maintenance association endpoint identifier) (Cont.)

Parameter name VLAN PCP bits

Abbreviated name vlanPrio

3GPP name -


Multiplicity 1

Description This parameter specifies the PCP bits value to be used for Service OAM messages for this Mainte-nance association Endpoint (MEP).

Range 0... 7

Step 1

Units -



Default value 7


Related functions -




Related options -



References -

Table 249 vlanPrio (VLAN PCP bits)

DN70577885 305

Flexi Transport Module Parameters OAMPRF Parameters


31 OAMPRF Parameters

31.1 activeMode (Link OAM operational mode at local peer)

Parameter name Link OAM operational mode at local peer

Abbreviated name activeMode

3GPP name -

Managed Object OAMPRF

Multiplicity 1

Description This parameter specifies the Link OAM operational mode at the local peer. If false the BTS shall only respond to a remotely initiated discovery process, if active the BTS shall itself initiate the process.


Step -

Units -


– false => 0 – true => 1



Related functions -







References -

Table 250 activeMode (Link OAM operational mode at local peer)

306 DN70577885



OAMPRF Parameters

31.2 alarmClearanceDelay (Link OAM Link Critical Event Alarm clearance delay)

31.3 efEventThreshold (Errored Frame Event counting thresh-old)

Parameter name Link OAM Link Critical Event Alarm clearance delay

Abbreviated name alarmClearanceDelay

3GPP name -


Multiplicity 1

Description This parameter specifies for how long critical event flags must have been cleared before the FTM will clear the corresponding Link OAM Critical Event alarm.

Range 1... 10

Step 1

Units seconds



Default value 1


Related functions -




Related options -



References -

Table 251 alarmClearanceDelay (Link OAM Link Critical Event Alarm clearance delay)

Parameter name Errored Frame Event counting threshold

Table 252 efEventThreshold (Errored Frame Event counting threshold)

DN70577885 307



31.4 efEventWindow (Errored Frame Event counting interval)

Abbreviated name efEventThreshold

3GPP name -


Multiplicity 1

Description This parameter specifies the threshold value for counting the Errored Frame Event. If the number of errored frames detected within the measurement window specified by efEventWindow is exceeded, the BTS transmits an OAM PDU Event Notification message for that event.

The maximum value of efEventThreshold equals "32 bit value".

Range 0... 4294967295

Step 1

Units -



Default value 1


Related functions -




Related options -



References -

Table 252 efEventThreshold (Errored Frame Event counting threshold) (Cont.)

Parameter name Errored Frame Event counting interval

Abbreviated name efEventWindow

3GPP name -

Table 253 efEventWindow (Errored Frame Event counting interval)

308 DN70577885



OAMPRF Parameters

31.5 efpEventThreshold (Errored Frame Period Event counting threshold)


Multiplicity 1

Description This parameter specifies the measurement interval for counting the Errored Frame Event. If the number of errored frames detected within the measurement interval exceeds the threshold number specified in parameter efEventThreshold, the FTM transmits an OAM PDU Event Notification message for that event.

Range 1... 60

Step 1

Units seconds



Default value 1


Related functions -




Related options -



References -

Table 253 efEventWindow (Errored Frame Event counting interval) (Cont.)

Parameter name Errored Frame Period Event counting threshold

Abbreviated name efpEventThreshold

3GPP name -


Multiplicity 1

Table 254 efpEventThreshold (Errored Frame Period Event counting threshold)

DN70577885 309



31.6 efpEventWindow (Errored Frame Period Event counting interval)

Description This parameter specifies the threshold value for counting the Errored Frame Period Event. If the number of received errored frames within the mea-surement window specified by efpEventWindow is exceeded, the BTS transmits an OAM PDU Event Notification message for that event.

The maximum value of efpEventThreshold equals "32 bit value".

Range 0... 4294967295

Step 1

Units -



Default value 1


Related functions -



efpEventWindow of OAMPRF - Configured value for efpEventThreshold should be within configured value for OAMPRF-efpEventWin-dow to enable the possibility of generating Errored Frame Period Event Notifications


Related options -



References -

Table 254 efpEventThreshold (Errored Frame Period Event counting threshold)

Parameter name Errored Frame Period Event counting interval

Abbreviated name efpEventWindow

Table 255 efpEventWindow (Errored Frame Period Event counting interval)

310 DN70577885



OAMPRF Parameters

31.7 efssEventThreshold (Errored Frame Seconds Summary Event counting threshold)

3GPP name -


Multiplicity 1

Description This parameter specifies the measurement interval for counting the Errored Frames. If the number of received errored frames within the measurement interval exceeds the threshold number specified in parameter efpEventThreshold, the BTS transmits an OAM PDU Event Notification message for that event.

Range 1... 4294967295

Step 1

Units -



Default value 1


Related functions -




Related options -



References -

Table 255 efpEventWindow (Errored Frame Period Event counting interval) (Cont.)

Parameter name Errored Frame Seconds Summary Event counting threshold

Abbreviated name efssEventThreshold

3GPP name -


Table 256 efssEventThreshold (Errored Frame Seconds Summary Event counting threshold)

DN70577885 311



31.8 efssEventWindow (Errored Frame Seconds Summary Event counting interval)

Multiplicity 1

Description This parameter specifies the threshold value for counting the Errored Frame Seconds Summary Event. If the number of errored frame seconds that occurred during the specified measurement interval specified by efssEventWindow is exceeded, the BTS transmits an OAM PDU Event Notification message for that event.

The maximum value of efssEventThreshold equals "16 bit value".

Range 0... 65535

Step 1

Units -



Default value 1


Related functions -




Related options -



References -

Table 256 efssEventThreshold (Errored Frame Seconds Summary Event counting threshold) (Cont.)

Parameter name Errored Frame Seconds Summary Event counting interval

Abbreviated name efssEventWindow

3GPP name -


Table 257 efssEventWindow (Errored Frame Seconds Summary Event counting interval)

312 DN70577885



OAMPRF Parameters

31.9 enableCcm (Allow sending of CCM messages and reset CCM counters)

Multiplicity 1

Description This parameter specifies the measurement interval for counting the Errored Frame Seconds Summary Event. If the number of errored frame seconds that occurred during the specified measurement interval exceeds the threshold number specified in param-eter efssEventThreshold, the BTS transmits an OAM PDU Event Notification message for that event.

Range 10... 900

Step 1

Units seconds



Default value 60


Related functions -




Related options -



References -

Table 257 efssEventWindow (Errored Frame Seconds Summary Event counting interval) (Cont.)

Parameter name Allow sending of CCM messages and reset CCM counters

Abbreviated name enableCcm

3GPP name -


Multiplicity 1


DN70577885 313



31.10 eventRepetition (OAM PDU message transmission rate)

Description This parameter allows sending continuity check messages (ETH_CCM) towards the remote Mainte-nance Association Endpoints (MEPs) of the End Point. Changing the parameter from false (not allowed) to true (allowed) resets the CCM counters of all remote MEPs.


Step -

Units -


– false => 0 – true => 1


Default value notes By default, sending CCM messages is not allowed.

Related functions -







References -


Parameter name OAM PDU message transmission rate

Abbreviated name eventRepetition

3GPP name -


Multiplicity 1

Table 259 eventRepetition (OAM PDU message transmission rate)

314 DN70577885



OAMPRF Parameters

31.11 eventSupport (Link OAM event support flag)

Description This parameter specifies how often the FTM repeats the transmission of OAM Events Notifica-tions to its remote peer to increase the probability that they are received by the remote peer. The parameter specifies the total number of repetitive transmissions of such messages.

Range 1... 4

Step 1

Units -



Default value 2


Related functions -


Related parameters activeMode of OAMPRF - Parameter eventRepetition is only relevant in Link OAM active mode (parameter activeMode = true).


Related options -



References -

Table 259 eventRepetition (OAM PDU message transmission rate) (Cont.)

Parameter name Link OAM event support flag

Abbreviated name eventSupport

3GPP name -


Multiplicity 1

Description This parameter specifies if the FTM supports Link OAM events.


Step -

Table 260 eventSupport (Link OAM event support flag)

DN70577885 315



31.12 linkLostTime (Link OAM link lost time)

Units -


– false => 0 – true => 1



Related functions -




Related options -



References -

Table 260 eventSupport (Link OAM event support flag) (Cont.)

Parameter name Link OAM link lost time

Abbreviated name linkLostTime

3GPP name -


Multiplicity 1

Description This parameter specifies the time for raising the Link OAM Link Lost Alarm. The Alarm shall be raised if no Link OAM PDUs are received for a period equal to linkLostTime. The alarm shall be cleared if Link OAM PDUs have been continuously received again for the same period of time.

Range 2... 10

Step 1

Units seconds



Default value 10


Table 261 linkLostTime (Link OAM link lost time)

316 DN70577885



OAMPRF Parameters

31.13 loopBackTime (Link OAM loopback duration)

Related functions -




Related options -



References -

Table 261 linkLostTime (Link OAM link lost time) (Cont.)

Parameter name Link OAM loopback duration

Abbreviated name loopBackTime

3GPP name -


Multiplicity 1

Description This parameter specifies the duration of a loopback operation initiated by the FTM.

The parameter is only relevant in Link OAM active mode.

Range 10... 600

Step 1

Units seconds



Default value 10


Related functions -


Related parameters activeMode of OAMPRF - Parameter loopBackTime is only relevant in Link OAM active mode (parameter activeMode = true).


Related options -

Table 262 loopBackTime (Link OAM loopback duration)

DN70577885 317



31.14 profileId (Profile instance identifier)



References -

Table 262 loopBackTime (Link OAM loopback duration) (Cont.)

Parameter name Profile instance identifier

Abbreviated name profileId

3GPP name -


Multiplicity 1

Description This parameter identifies an Ethernet link OAM profile.

Range 1... 5

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 263 profileId (Profile instance identifier)

318 DN70577885



OAMPRF Parameters

31.15 testFrameRate (Link OAM loopback test message rate)

31.16 testFrameSize (Link OAM loopback test message frame size)

Parameter name Link OAM loopback test message rate

Abbreviated name testFrameRate

3GPP name -


Multiplicity 1

Description This parameter specifies the number of frames / second to be sent during loopback operation for Link OAM.

Value 0 switched the test frame generator off.

Range 0... 25000

Step 1

Units -



Default value 1


Related functions -







References -

Table 264 testFrameRate (Link OAM loopback test message rate)

Parameter name Link OAM loopback test message frame size

Abbreviated name testFrameSize

Table 265 testFrameSize (Link OAM loopback test message frame size)

DN70577885 319



3GPP name -


Multiplicity 1

Description This parameter specifies the ethernet frame size of test messages sent during loopback operation for Link OAM.

Range 64... 1518

Step 1

Units -



Default value 64

Default value notes Default is minimum PDU size.

Related functions -







References -

Table 265 testFrameSize (Link OAM loopback test message frame size) (Cont.)

320 DN70577885



OSPFV2 Parameters

32 OSPFV2 Parameters

32.1 confPref (OSPF routing preference value)

32.2 ospfAreas (OSPF area list)

Parameter name OSPF routing preference value

Abbreviated name confPref

3GPP name -

Managed Object OSPFV2

Multiplicity 1

Description This parameter specifies the preference value of the OSPF protocol. The preference value is used in calculating the cost of an OSPF based route.

Range 1... 254

Step 1

Units -



Default value 110


Related functions -







References -

Table 266 confPref (OSPF routing preference value)

Parameter name OSPF area list

Abbreviated name ospfAreas

Table 267 ospfAreas (OSPF area list)

DN70577885 321

Flexi Transport Module Parameters OSPFV2 Parameters


32.3 areaId (OSPF area identifier)

3GPP name -


Multiplicity 1

Description This parameter specifies the properties of all OSPF areas configured for the OSPF router. In this release only 1 area is supported.


-

Default value -


Related functions -

Child parameters – areaId– areaStub







References -

Table 267 ospfAreas (OSPF area list) (Cont.)

Parameter name OSPF area identifier

Abbreviated name areaId

3GPP name -

Managed Object -

Multiplicity 1

Description This parameter specifies a unique identifier for the OSPF area in IP notation.

Range 7...15

Step -

Table 268 areaId (OSPF area identifier)

322 DN70577885



OSPFV2 Parameters

32.4 areaStub (OSPF area stub flag)

Units characters



Default value -


Related functions -







References -

Table 268 areaId (OSPF area identifier) (Cont.)

Parameter name OSPF area stub flag

Abbreviated name areaStub

3GPP name -

Managed Object -

Multiplicity 1

Description This parameter specifies whether the OSPF area is a stub area. OSPF backbone area "0.0.0.0" cannot be stub area.


Step -

Units -


– false => 0 – true => 1



Related functions -

Table 269 areaStub (OSPF area stub flag)

DN70577885 323



32.5 ospfEnabled (OSPF enabling flag)







References -

Table 269 areaStub (OSPF area stub flag) (Cont.)

Parameter name OSPF enabling flag

Abbreviated name ospfEnabled

3GPP name -


Multiplicity 1

Description If set to true, this parameter enables OSPF.

Note: OSPF is not supported on the following modules:

FTEB, FTHA, FTPB, FTFA.


Step -

Units -


– false => 0 – true => 1



Related functions -


Table 270 ospfEnabled (OSPF enabling flag)

324 DN70577885



OSPFV2 Parameters

32.6 ospfRouterId (OSPF router identification)


unitTypeExpected of UNIT - OSPF is not supported on the following modules:





References -

Table 270 ospfEnabled (OSPF enabling flag) (Cont.)

Parameter name OSPF router identification

Abbreviated name ospfRouterId

3GPP name -


Multiplicity 1

Description This parameter identifies the OSPF router through an IP address. If the operator sets the parameter to 0.0.0.0 the FTM will overwrite the value as follows:

- with the highest configured virtual IP address in the applications binding map of the IPNO class

- if none of the IP addresses of that map is a virtual IP address, the FTM shall overwrite the parameter with the highest network interface IP address.

Range 7...15

Step -

Units characters




Default value notes Value 0.0.0.0 means "not specified".

Related functions -


Table 271 ospfRouterId (OSPF router identification)

DN70577885 325



32.7 ospfV2Id (OSPF configuration identifier)


ospfEnabled of OSPFV2 - "ospfRouterId" should be overwritten if ospfEn-abled is true and areaId is 0.0.0.0.





References -

Table 271 ospfRouterId (OSPF router identification) (Cont.)

Parameter name OSPF configuration identifier

Abbreviated name ospfV2Id

3GPP name -


Multiplicity 1

Description This parameter identifies the OSPF configuration object. Value is always 1.

Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -


Table 272 ospfV2Id (OSPF configuration identifier)

326 DN70577885



OSPFV2 Parameters

32.8 refBandwidth (Reference bandwidth for OSPF cost equal to 1)


References -

Table 272 ospfV2Id (OSPF configuration identifier) (Cont.)

Parameter name Reference bandwidth for OSPF cost equal to 1

Abbreviated name refBandwidth

3GPP name -


Multiplicity 1

Description This parameter specifies the bandwidth for which the OSPF cost is considered to be 1.

Range 1... 65535

Step 1

Units mbps



Default value 10000

Default value notes Default is 10 GBps.

Related functions -







References -

Table 273 refBandwidth (Reference bandwidth for OSPF cost equal to 1)

DN70577885 327



32.9 spfDelay (OSPF Shortest Path First recalculation delay)

32.10 spfHoldTime (OSPF Shortest Path First hold time)

Parameter name OSPF Shortest Path First recalculation delay

Abbreviated name spfDelay

3GPP name -


Multiplicity 1

Description This parameter specifies the minimum amount of time to delay the Shortest Path First (SPF) recalcu-lation after a topology change event is received. Value is in milliseconds. Value range is from 0 mil-liseconds to 10 minutes.

Range 0... 600000

Step 1

Units ms



Default value 200


Related functions -







References -

Table 274 spfDelay (OSPF Shortest Path First recalculation delay)

Parameter name OSPF Shortest Path First hold time

Abbreviated name spfHoldTime

3GPP name -

Table 275 spfHoldTime (OSPF Shortest Path First hold time)

328 DN70577885



OSPFV2 Parameters

32.11 spfMaxHoldTime (OSPF maximum Shortest Path First hold time)


Multiplicity 1

Description This parameter specifies the time between consec-utive Shortest Path First (SPF) calculations.

Value range is from 0 milliseconds to 10 minutes.

Range 0... 600000

Step 1

Units ms



Default value 5000


Related functions -







References -

Table 275 spfHoldTime (OSPF Shortest Path First hold time) (Cont.)

Parameter name OSPF maximum Shortest Path First hold time

Abbreviated name spfMaxHoldTime

3GPP name -


Multiplicity 1

Table 276 spfMaxHoldTime (OSPF maximum Shortest Path First hold time)

DN70577885 329



Description This parameter specifies the maximum hold time for Shortest Path First (SPF) calculations. Events which occur within the hold time of an ongoing SPF calculation will cause the overall holdtime to be increased by the value of spfHoldTime. If the overall holdtime surpasses the maximum hold time (spfMaxHoldTime) it is reset to the value of spfHold-Time.

Value is in milliseconds. Value range is from 0 mil-liseconds to 10 minutes.

Range 0... 600000

Step 1

Units ms



Default value 80000


Related functions -







References -

Table 276 spfMaxHoldTime (OSPF maximum Shortest Path First hold time) (Cont.)

330 DN70577885



P3LP Parameters

33 P3LP Parameters

33.1 acFieldCompressionOn (Access Control Field Compres-sion flag)

Parameter name Access Control Field Compression flag

Abbreviated name acFieldCompressionOn

3GPP name -

Managed Object P3LP

Multiplicity 1

Description If acFieldCompressionOn is true, the Address & Control Field (ACF) is compressed (saves 2 bytes, RFC-1661 chapter 6.6).


Step -

Units -


– false => 0 – true => 1



Related functions -




Related options – RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces



References -

Table 277 acFieldCompressionOn (Access Control Field Compression flag)

DN70577885 331

Flexi Transport Module Parameters P3LP Parameters


33.2 fcsFieldLength (Frame Check Sequence field size)

33.3 magicNumberOn (Magic number flag)

Parameter name Frame Check Sequence field size

Abbreviated name fcsFieldLength

3GPP name -

Managed Object P3LP

Multiplicity 1

Description This parameter specificies the size of the Frame Check Sequence (FCS) field in bits (RFC 1570).

Range fcs0 (0), fcs16 (1), fcs32 (2)

Step -

Units -


gui ==> internal

fcs0 ==> 0

fcs16 ==> 1

fcs32 ==> 2

Default value fcs16 (1)


Related functions -







References -

Table 278 fcsFieldLength (Frame Check Sequence field size)

Parameter name Magic number flag

Abbreviated name magicNumberOn

Table 279 magicNumberOn (Magic number flag)

332 DN70577885



P3LP Parameters

33.4 mruSize (Maximum Receive Unit (MRU) size)

3GPP name -

Managed Object P3LP

Multiplicity 1

Description A magic number provides a way to detect looped-back links and other data link layer anomalies by sending a number that is otherwise unlikely to happen (RFC-1661chapter 6.4). The attribute decides if the option is used.


Step -

Units -


– false => 0 – true => 1



Related functions -







References -

Table 279 magicNumberOn (Magic number flag) (Cont.)

Parameter name Maximum Receive Unit (MRU) size

Abbreviated name mruSize

3GPP name -

Managed Object P3LP

Multiplicity 1

Table 280 mruSize (Maximum Receive Unit (MRU) size)

DN70577885 333



Description This parameter specifies maximum receive unit size in octets.

A LCP MRU Configure-Request shall be sent auto-matically when a different value than the default 1500 bytes is set for parameter mruSize. Otherwise no Configure-Request shall be sent.

For IHSPA the maximum mruSize is 1600.

The BTS sends an alarm is the size of a received packet surpasses the mruSize.

Range PACKET_SIZE_1500 (1500),

PACKET_SIZE_1520 (1520),





PACKET_SIZE_1604 (1604)


PACKET_SIZE_1630 (1630) for WN7.0 1.0;








PACKET_SIZE_1630 (1630) for WN7.0 2.0

Step -

Units -


gui ==> internal

PACKET_SIZE_1500 ==> 1500








Table 280 mruSize (Maximum Receive Unit (MRU) size) (Cont.)

334 DN70577885



P3LP Parameters

33.5 p3lpId (PPP link identifier)

Default value PACKET_SIZE_1500 (1500)


Related functions -







References -

Table 280 mruSize (Maximum Receive Unit (MRU) size) (Cont.)

Parameter name PPP link identifier

Abbreviated name p3lpId

3GPP name -

Managed Object P3LP

Multiplicity 1

Description This parameter identifies the PPP link.

The format is slot#-if#

where slot# is always 1 (slot number) and

if# = 1..16 (interface number).

Range 3...4

Step -

Units characters



Default value -


Related functions -


Table 281 p3lpId (PPP link identifier)

DN70577885 335



33.6 protocolFieldCompressionOn (Protocol Field Compres-sion flag)






References -

Table 281 p3lpId (PPP link identifier) (Cont.)

Parameter name Protocol Field Compression flag

Abbreviated name protocolFieldCompressionOn

3GPP name -

Managed Object P3LP

Multiplicity 1

Description The Protocol Field (PCF) in LCP packets by default has 2 octets. If the PCF option is used, it is com-pressed to 1 octet (RFC-1661 chapter 6.5). If proto-colFieldCompressionOn equals true, the option is used.


Step -

Units -


– false => 0 – true => 1



Related functions -



Table 282 protocolFieldCompressionOn (Protocol Field Compression flag)

336 DN70577885



P3LP Parameters





References -

Table 282 protocolFieldCompressionOn (Protocol Field Compression flag) (Cont.)

DN70577885 337

Flexi Transport Module Parameters P3ML Parameters


34 P3ML Parameters

34.1 administrativeState (Administrative state of the PPP multi-link)

Parameter name Administrative state of the PPP multi-link


3GPP name -

Managed Object P3ML

Multiplicity 1

Description This parameter is used to lock and unlock the PPP multi-link. Locking the PPP multi-link deactivates it.


Step -

Units -


gui ==> internal

locked ==> 0

unlocked ==> 1


Default value notes The interface is locked.

Related functions -







References -

Table 283 administrativeState (Administrative state of the PPP multi-link)

338 DN70577885



P3ML Parameters

34.2 endPointDiscriminatorType (Endpoint discriminator type)

34.3 interfaces (Physical interface list)

Parameter name Endpoint discriminator type

Abbreviated name endPointDiscriminatorType

3GPP name -

Managed Object P3ML

Multiplicity 1

Description The Endpoint Discriminator Option is a way to dynamically link to an existing multilink bundle of the peer or to create a new multilink bundle in the peer (RFC 1990 chapter 5.5.3). The attribute decides if the option is used.

Range NORMAL (0), EDGE (1)

Step -

Units -


gui ==> internal

NORMAL ==> 0

EDGE ==> 1

Default value NORMAL (0)


Related functions -







References -

Table 284 endPointDiscriminatorType (Endpoint discriminator type)


Table 285 interfaces (Physical interface list)

DN70577885 339



34.4 mpFragmentSize (Fragment size in egress direction)

Abbreviated name interfaces

3GPP name -

Managed Object P3ML

Multiplicity 16

Description This parameter holds the list of the physical inter-faces used for MLPPP.

The maximum number of interfaces in one MLPPP interface depends on the unit type:

FIIB, FILB, FTIA, FTIB, FTJA, FTLB: 4

FTEB, FTPB, FTFA: 8

FTFA, FTHA, FTFB: 16

Interfaces have to be selected consecutively starting with 1.

Range 1... 16

Step 1

Units -



Default value -


Related functions -







References -

Table 285 interfaces (Physical interface list) (Cont.)

Parameter name Fragment size in egress direction

Table 286 mpFragmentSize (Fragment size in egress direction)

340 DN70577885



P3ML Parameters

34.5 mrruSize (Maximum Receive Reconstructed Unit (MRRU) size)

Abbreviated name mpFragmentSize

3GPP name -

Managed Object P3ML

Multiplicity 1

Description This parameter specificies the PPP MultiLink Protocol fragment size in egress direction in octets.

Range FRAGMENT_SIZE_128 (128), FRAGMENT_SIZE_256 (256), FRAGMENT_SIZE_512 (512)

Step -

Units -


gui ==> internal

FRAGMENT_SIZE_128 ==> 128



Default value FRAGMENT_SIZE_256 (256)


Related functions -







References -

Table 286 mpFragmentSize (Fragment size in egress direction) (Cont.)

Parameter name Maximum Receive Reconstructed Unit (MRRU) size

Table 287 mrruSize (Maximum Receive Reconstructed Unit (MRRU) size)

DN70577885 341



Abbreviated name mrruSize

3GPP name -

Managed Object P3ML

Multiplicity 1

Description This parameter specifies maximum receive recon-structed unit size in octets.

The MRRU option shall always be sent as part of every LCP negotiation and applies to then to the bundle.

For IHSPA the maximum mruSize is 1600.

The BTS sends an alarm is the size of a received packet surpasses the mrruSize.

Range PACKET_SIZE_1500 (1500), PACKET_SIZE_1520 (1520), PACKET_SIZE_1540 (1540), PACKET_SIZE_1560 (1560), PACKET_SIZE_1580 (1580), PACKET_SIZE_1600 (1600), PACKET_SIZE_1620 (1620), PACKET_SIZE_1630 (1630)

Step -

Units -


gui ==> internal









Default value PACKET_SIZE_1500 (1500)


Related functions -




Table 287 mrruSize (Maximum Receive Reconstructed Unit (MRRU) size) (Cont.)

342 DN70577885



P3ML Parameters

34.6 netmask (Netmask of the IP address of the PPP endpoint)




References -

Table 287 mrruSize (Maximum Receive Reconstructed Unit (MRRU) size) (Cont.)

Parameter name Netmask of the IP address of the PPP endpoint


3GPP name -

Managed Object P3ML

Multiplicity 1

Description Netmask for the primary IP address of the PPP end-point. To be entered in dotted decimal format.

Range 7...15

Step -

Units characters



Default value -


Related functions -







Table 288 netmask (Netmask of the IP address of the PPP endpoint)

DN70577885 343



34.7 p3mlId (PPP multi-link identifier)

34.8 p3pIpAddr (PPP endpoint IP address)

References -

Table 288 netmask (Netmask of the IP address of the PPP endpoint) (Cont.)

Parameter name PPP multi-link identifier

Abbreviated name p3mlId

3GPP name -

Managed Object P3ML

Multiplicity 1

Description This parameter identifies the unique PPP multi-link object in the BTS. Value is always 1.

Range 1... 1

Step 1

Units -



Default value -

Default value notes Always 1. Only 1 PPP multi-link can exist.

Related functions -







References -

Table 289 p3mlId (PPP multi-link identifier)

Parameter name PPP endpoint IP address

Table 290 p3pIpAddr (PPP endpoint IP address)

344 DN70577885



P3ML Parameters

34.9 shortSeqNrOn (Short sequence numbering flag)

Abbreviated name p3pIpAddr

3GPP name -

Managed Object P3ML

Multiplicity 1

Description IP address of the PPP endpoint in the transport network. To be entered in dotted decimal format.

Range 7...15

Step -

Units characters



Default value -


Related functions -







References -

Table 290 p3pIpAddr (PPP endpoint IP address) (Cont.)

Parameter name Short sequence numbering flag

Abbreviated name shortSeqNrOn

3GPP name -

Managed Object P3ML

Multiplicity 1

Table 291 shortSeqNrOn (Short sequence numbering flag)

DN70577885 345



34.10 ts16Excluded (Is timeslot TS16 excluded)


This parameter specificies how packets are num-bered. The Long Sequence Number Format uses 24 bits for the fragment sequence number, the short sequence format 12 bits (RFC 1990). If short-SeqNrOn equals true, the short sequence number is used.


Step -

Units -


– false => 0 – true => 1



Related functions -







References -

Table 291 shortSeqNrOn (Short sequence numbering flag) (Cont.)

Parameter name Is timeslot TS16 excluded

Abbreviated name ts16Excluded

3GPP name -

Managed Object P3ML

Multiplicity 1

Table 292 ts16Excluded (Is timeslot TS16 excluded)

346 DN70577885



P3ML Parameters

Description This parameter specifies if timeslot TS16 is used. By default all timeslots from TS1 to TS31 are used. If parameter TS16Excluded has value true, timeslots TS1..TS15 and TS17..TS31 are used.


Step -

Units -


– false => 0 – true => 1


Default value notes By default timeslot TS16 is included for E1. All timeslots from TS1 to TS31 are used.

Related functions -







References -

Table 292 ts16Excluded (Is timeslot TS16 excluded) (Cont.)

DN70577885 347

Flexi Transport Module Parameters P3SL Parameters


35 P3SL Parameters

35.1 administrativeState (Administrative state of the PPP link)

35.2 interface (Physical interface list)

Parameter name Administrative state of the PPP link


3GPP name -

Managed Object P3SL

Multiplicity 1

Description This parameter is used to lock and unlock the PPP link. Locking the PPP link deactivates it.


Step -

Units -


gui ==> internal

locked ==> 0

unlocked ==> 1


Default value notes The interface is locked.

Related functions -







References -

Table 293 administrativeState (Administrative state of the PPP link)


Table 294 interface (Physical interface list)

348 DN70577885



P3SL Parameters

35.3 netmask (Netmask for the IP address of the PPP endpoint)

Abbreviated name interface

3GPP name -

Managed Object P3SL

Multiplicity 1

Description This parameter holds the physical interface id used by the PPP link over PDH.

This id is restricted by the number of interfaces present in the transport module. Only IF 1 is sup-ported for current release.

Range 1... 16

Step 1

Units -



Default value -


Related functions -







References -

Table 294 interface (Physical interface list) (Cont.)

Parameter name Netmask for the IP address of the PPP endpoint


3GPP name -

Managed Object P3SL

Table 295 netmask (Netmask for the IP address of the PPP endpoint)

DN70577885 349



35.4 p3pIpAddr (PPP endpoint IP address)

Multiplicity 1

Description Netmask for the primary IP address of the PPP end-point. To be entered in dotted decimal format.

Range 7...15

Step -

Units characters



Default value -


Related functions -







References -

Table 295 netmask (Netmask for the IP address of the PPP endpoint) (Cont.)

Parameter name PPP endpoint IP address

Abbreviated name p3pIpAddr

3GPP name -

Managed Object P3SL

Multiplicity 1

Description IP address of the PPP endpoint in the transport network. To be entered in dotted decimal format.

Range 7...15

Step -

Units characters

Table 296 p3pIpAddr (PPP endpoint IP address)

350 DN70577885



P3SL Parameters

35.5 p3slId (PPP single link object instance identifier)



Default value -


Related functions -







References -

Table 296 p3pIpAddr (PPP endpoint IP address) (Cont.)

Parameter name PPP single link object instance identifier

Abbreviated name p3slId

3GPP name -

Managed Object P3SL

Multiplicity 1

Description This is the object instance identifier of the PPP single link object. The value is always 1.

Range 1... 1

Step 1

Units -



Default value -


Related functions -


Table 297 p3slId (PPP single link object instance identifier)

DN70577885 351



35.6 ts16Excluded (Is timeslot TS16 excluded)






References -

Table 297 p3slId (PPP single link object instance identifier) (Cont.)

Parameter name Is timeslot TS16 excluded

Abbreviated name ts16Excluded

3GPP name -

Managed Object P3SL

Multiplicity 1

Description This parameter specifies if timeslot TS16 is used. By default all timeslots from TS1 to TS31 are used. If parameter TS16Excluded has value true, timeslots TS1..TS15 and TS17..TS31 are used.


Step -

Units -


– false => 0 – true => 1


Default value notes By default timeslot TS16 is included for E1. All timeslots from TS1 to TS31 are used.

Related functions -




Table 298 ts16Excluded (Is timeslot TS16 excluded)

352 DN70577885



P3SL Parameters




References -

Table 298 ts16Excluded (Is timeslot TS16 excluded) (Cont.)

DN70577885 353

Flexi Transport Module Parameters PPTT Parameters


36 PPTT Parameters





3GPP name -

Managed Object PPTT

Multiplicity 1

Description Used to lock and unlock the interface.

Locking the interface deactivates it and all alarms and any ATM cell transfer is suppressed.


Step -

Units -


gui ==> internal

locked ==> 0

unlocked ==> 1



Related functions -




Related options -

Feature dependencies – Physical Interfaces E1, T1, JT1


References -





354 DN70577885



PPTT Parameters

36.3 pdhLbo (PDH Line Build Out)

3GPP name -

Managed Object PPTT

Multiplicity 1

Description Defines the interface location on the unit.

The number of interfaces depends on the unit type.



FTFB, FTHA, FTFA: 1..16

Range 1... 16

Step 1

Units -



Default value -


Related functions -




Related options -



References -


Parameter name PDH Line Build Out

Abbreviated name pdhLbo

3GPP name -

Managed Object PPTT

Multiplicity 1

Table 301 pdhLbo (PDH Line Build Out)

DN70577885 355



36.4 pdhLineType (PDH Line Type)

Description Specifies the attenuation for the signal from the transmitter.

All attenuation values are specified in dB at 772 kHz. This parameter is only supported on T1 inter-faces.

Range PDH_LBO_0 (1), PDH_LBO_7_5 (2), PDH_LBO_15 (3)

Step -

Units -


gui ==> internal

PDH_LBO_0 ==> 1

PDH_LBO_7_5 ==> 2

PDH_LBO_15 ==> 3

Default value PDH_LBO_0 (1)


Related functions -




Related options -



References -

Table 301 pdhLbo (PDH Line Build Out) (Cont.)

Parameter name PDH Line Type

Abbreviated name pdhLineType

3GPP name -

Managed Object PPTT

Multiplicity 1

Table 302 pdhLineType (PDH Line Type)

356 DN70577885



PPTT Parameters

Description Specifies the frame format of the PDH signal for a physical PDH interface of a unit.

E1 (G.704):

- DOUBLEFRAME

- MULTIFRAME

- DOUBLEFRAME UNBALANCED

- MULTIFRAME UNBALANCED

T1: EXTENDED_SUPERFRAME

JT1: EXTENDED_MULTIFRAME

NOTEs:

1) This parameter is "not modifiable" for FTIB and FTLB hardware unit.

2) For FTIB and FTLB hardware unit UNBAL-ANCED mode is not supported at all.

Range PDH_LINE_TYPE_DOUBLE_FRAME_G704 (1), PDH_LINE_TYPE_MULTI_FRAME_G704 (2), PDH_LINE_TYPE_EXTENDED_MULTIFRAME (8), PDH_LINE_TYPE_EXTENDED_SUPERFRAME (11), PDH_LINE_TYPE_DOUBLE_FRAME_G704_UNBALANCED (12), PDH_LINE_TYPE_MULTI_FRAME_G704_UNBALANCED (13)

Step -

Units -


gui ==> internal

PDH_LINE_TYPE_DOUBLE_FRAME_G704 ==> 1

PDH_LINE_TYPE_MULTI_FRAME_G704 ==> 2

PDH_LINE_TYPE_EXTENDED_MULTIFRAME ==> 8

PDH_LINE_TYPE_EXTENDED_SUPERFRAME ==> 11

PDH_LINE_TYPE_DOUBLE_FRAME_G704_UNBALANCED ==> 12

PDH_LINE_TYPE_MULTI_FRAME_G704_UNBALANCED ==> 13

Default value -

Table 302 pdhLineType (PDH Line Type) (Cont.)

DN70577885 357



36.5 pdhPSTTPId (PDH Interface Identifier)

Default value notes Defaults depend on E1/T1/JT1:E1: PDH_LINE_TYPE_MULTI_FRAME_G704T1: PDH_LINE_TYPE_EXTENDED_SUPERFRAMEJT1: PDH_LINE_TYPE_EXTENDED_MULTIFRAME

Related functions -



Parameter relationships When setting the PDH Line Type to another inter-face type (E1/T1/JT1), FTM switches on all inter-faces of this unit the PDH Line Type to the default value for that interface type. In the second configu-ration step the framing format within this interface type can be modified.

Notes

1) In case of switching the line type, all ATM, IMA and CES objects that are associated with this unit are deleted!

2) PdhLineType is not modifiable for the FTIB and the FTLB hardware unit. It must be set on creation of the object instance.

3) UNBALANCED mode is not supported at all for the FTIB and FTLB hardware unit.

Related options -



References -

Table 302 pdhLineType (PDH Line Type) (Cont.)

Parameter name PDH Interface Identifier

Abbreviated name pdhPSTTPId

3GPP name -

Managed Object PPTT

Multiplicity 1

Table 303 pdhPSTTPId (PDH Interface Identifier)

358 DN70577885



PPTT Parameters

Description This parameter identifies a PDH interface.

Format: unit#-if#

where

unit# = slot number of the unit containing the PDH interfaces, and

if# = the interface number of the physical interface on the unit

and

for FIIB/FILB/FTIA/FTIB/FTJA/FTLB,

unit#: 1 : This is always 1, since there is only 1 slot.

if#: 1..4

for FTFB/FTHA/FTFA,

unit#: 1 : This is always 1, since there is only 1 slot.

if#: 1..16

for FTEB/FTPB/FTIF/FIIF,

unit#: 1 : The slot number is '1', since this is an additional unit

if#: 1..8 : Value range is 1..8 for IF1..IF8 on this unit

Range 3...4

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 303 pdhPSTTPId (PDH Interface Identifier) (Cont.)

DN70577885 359






3GPP name -

Managed Object PPTT

Multiplicity 1

Description Specifies the location of the unit providing the PDH interface. In this release it is always 1.

Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -



References -


360 DN70577885



PWMP Parameters

37 PWMP Parameters

37.1 bfdAdminUp (BFD actual session administration flag)

37.2 bfdEnable (Bidirectional Forwarding Enabled)

Parameter name BFD actual session administration flag

Abbreviated name bfdAdminUp

3GPP name -

Managed Object PWMP

Multiplicity 1

Description This parameter is used to switch on or off the actual BFD session.

Note that this parameter is only relevant if parame-ter bfdEnable has value true.


Step -

Units -


– false => 0 – true => 1



Related functions -


Related parameters bfdEnable of PWMP

Parameter relationships bfdAdminUp is only relevant if bfdEnable has value true.

Related options -

Feature dependencies – RAN1142 ATM over Ethernet for BTS


References -

Table 305 bfdAdminUp (BFD actual session administration flag)

Parameter name Bidirectional Forwarding Enabled

Table 306 bfdEnable (Bidirectional Forwarding Enabled)

DN70577885 361

Flexi Transport Module Parameters PWMP Parameters


37.3 cellsConcatUl (Uplink Concatenation Factor.)

Abbreviated name bfdEnable

3GPP name -

Managed Object PWMP

Multiplicity 1

Description This parameter switches the BFD session on or off for each PW. BFD comprises VCCV-BFD (== PW OAM)and VCCV = Virtual Channel Continuity Veri-fication.


Step -

Units -


– false => 0 – true => 1



Related functions -




Related options -



References -

Table 306 bfdEnable (Bidirectional Forwarding Enabled) (Cont.)

Parameter name Uplink Concatenation Factor.

Abbreviated name cellsConcatUl

3GPP name -

Managed Object PWMP

Multiplicity 1

Description Uplink Concatenation Factor.

Range 1... 28

Table 307 cellsConcatUl (Uplink Concatenation Factor.)

362 DN70577885



PWMP Parameters

37.4 ctpList (Set of registered vcCTPs.)

Step 1

Units -



Default value 28


Related functions -




Related options -



References -

Table 307 cellsConcatUl (Uplink Concatenation Factor.) (Cont.)

Parameter name Set of registered vcCTPs.

Abbreviated name ctpList

3GPP name -

Managed Object PWMP

Multiplicity 100

Description Set of registered vcCTPs.

Represented as Local MOId strings of VCCT without the prefix "DN:"

Example: "VPTT-1-76-2/VCCT-32"

Range 10...32

Step -

Units characters



Default value -


Table 308 ctpList (Set of registered vcCTPs.)

DN70577885 363



37.5 labelDl (Downlink MPLS Header)

Related functions -




Related options -



References -

Table 308 ctpList (Set of registered vcCTPs.) (Cont.)

Parameter name Downlink MPLS Header

Abbreviated name labelDl

3GPP name -

Managed Object PWMP

Multiplicity 1

Description Downlink MPLS Header (inner label)

Range 16... 1048575

Step 1

Units -



Default value -


Related functions -




Related options -



Table 309 labelDl (Downlink MPLS Header)

364 DN70577885



PWMP Parameters

37.6 labelUl (Uplink MPLS Header)

37.7 perHopBehaviour (Per hop behaviour DiffServ)

References -

Table 309 labelDl (Downlink MPLS Header) (Cont.)

Parameter name Uplink MPLS Header

Abbreviated name labelUl

3GPP name -

Managed Object PWMP

Multiplicity 1

Description Uplink MPLS Header (inner label)

Range 16... 1048575

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 310 labelUl (Uplink MPLS Header)

Parameter name Per hop behaviour DiffServ

Abbreviated name perHopBehaviour

3GPP name -

Managed Object PWMP

Table 311 perHopBehaviour (Per hop behaviour DiffServ)

DN70577885 365



Multiplicity 1

Description Per hop behaviour (DiffServ). This parameter is used to determine the DSCP value(Diff Serv Code Point) that must be stored in the first 6 bits of the 'Type of Service' (ToS) field that is part of the standard IP header. The DSCP for the given per-HopBehaviour is configured in the trafficTypesMap of the QOS object.

Range expeditedForwarding (0), assuredForwardingClass4 (1), assuredForwardingClass3 (2), assuredForwardingClass2 (3), assuredForwardingClass1 (4), bestEffort (5)

Step -

Units -


gui ==> internal

expeditedForwarding ==> 0

assuredForwardingClass4 ==> 1




bestEffort ==> 5

Default value bestEffort (5)


Related functions -


Related parameters trafficTypesMap of QOS

Parameter relationships perHopBehaviour is used as a search criterium in the trafficTypesMap to find the corresponding DSCP value.

Related options -



References -

Table 311 perHopBehaviour (Per hop behaviour DiffServ) (Cont.)

366 DN70577885



PWMP Parameters

37.8 pkTimer (Packetization Timer)

Parameter name Packetization Timer

Abbreviated name pkTimer

3GPP name -

Managed Object PWMP

Multiplicity 1

Description This parameter shall define for each PW the maximum time allowed to create a PW frame. Value range is [500, 5000] µs, possible values are 500, 1000, 2000, 3000, 4000 and 5000 µs.

Please note that small deviations between actual and nominal values exist in the implementation. These must be taken into account by the planning tools.

Range 500 (500), 1000 (1000), 2000 (2000), 3000 (3000), 4000 (4000), 5000 (5000)

Step -

Units -


gui ==> internal

500 ==> 500

1000 ==> 1000

2000 ==> 2000

3000 ==> 3000

4000 ==> 4000

5000 ==> 5000

Default value 500 (500)


Related functions -




Related options -



References -

Table 312 pkTimer (Packetization Timer)

DN70577885 367



37.9 pwMplsId (MPLS Pseudowire Identifier)

Parameter name MPLS Pseudowire Identifier

Abbreviated name pwMplsId

3GPP name -

Managed Object PWMP

Multiplicity 1

Description Identifies the MPLS Pseudowire. Format: slot#-mp# where

slot# = 1

mp# = 1..6

Range 3

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 313 pwMplsId (MPLS Pseudowire Identifier)

368 DN70577885



PWNE Parameters

38 PWNE Parameters

38.1 bfdTimer (BFD Timer)

38.2 bfdDetectMult (Maximum allowed number of lost control packets for BFD)

Parameter name BFD Timer

Abbreviated name bfdTimer

3GPP name -

Managed Object PWNE

Multiplicity 1

Description Timing details for VCCV-BFD. (i.e. PW OAM)

Only one value set must be defined


-

Default value -


Related functions -

Child parameters – bfdDetectMult– desiredMinTxIntvl– requiredMinRxIntvl




Related options -



References -

Table 314 bfdTimer (BFD Timer)

Parameter name Maximum allowed number of lost control packets for BFD

Abbreviated name bfdDetectMult

Table 315 bfdDetectMult (Maximum allowed number of lost control packets for BFD)

DN70577885 369

Flexi Transport Module Parameters PWNE Parameters


38.3 desiredMinTxIntvl (Desired Minimum Transmit Interval)

3GPP name -

Managed Object -

Multiplicity 1

Description This parameter holds the number of control packets that the BTS may lose before the BFD session is declared down.

Range 2... 10

Step 1

Units -



Default value 5


Related functions -




Related options -



References -

Table 315 bfdDetectMult (Maximum allowed number of lost control packets for BFD)

Parameter name Desired Minimum Transmit Interval

Abbreviated name desiredMinTxIntvl

3GPP name -

Managed Object -

Multiplicity 1

Description Desired minimum transmit interval for the control word in ms.

Range 500... 5000

Step 500

Table 316 desiredMinTxIntvl (Desired Minimum Transmit Interval)

370 DN70577885



PWNE Parameters

38.4 requiredMinRxIntvl (Required Minimum Receive Interval)

Units -



Default value 500


Related functions -




Related options -



References -

Table 316 desiredMinTxIntvl (Desired Minimum Transmit Interval) (Cont.)

Parameter name Required Minimum Receive Interval

Abbreviated name requiredMinRxIntvl

3GPP name -

Managed Object -

Multiplicity 1

Description Required minimum receive interval for the control word in ms.

Range 500... 5000

Step 500

Units -



Default value 500


Related functions -



Table 317 requiredMinRxIntvl (Required Minimum Receive Interval)

DN70577885 371

Flexi Transport Module Parameters PWNE Parameters


38.5 cwEnable (Control Word Enable)


Related options -



References -

Table 317 requiredMinRxIntvl (Required Minimum Receive Interval) (Cont.)

Parameter name Control Word Enable

Abbreviated name cwEnable

3GPP name -

Managed Object PWNE

Multiplicity 1

Description Enables the setting of the Control Word bits in the data packet.


Step -

Units -


– false => 0 – true => 1



Related functions -




Related options -



References -

Table 318 cwEnable (Control Word Enable)

372 DN70577885



PWNE Parameters

38.6 pwNeId (Pseudowire Network Element Identifier)

Parameter name Pseudowire Network Element Identifier

Abbreviated name pwNeId

3GPP name -

Managed Object PWNE

Multiplicity 1

Description There is alway only one instance of this class. It is identified with 1

Range 1

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 319 pwNeId (Pseudowire Network Element Identifier)

DN70577885 373

Flexi Transport Module Parameters PWTIP Parameters


39 PWTIP Parameters


39.2 attachedPWList (Attached Pseudo-Wires List)



3GPP name -

Managed Object PWTIP

Multiplicity 1


Locking the interface deactivates it and all alarms and any ATM cell transfer is suppressed.


Step -

Units -


gui ==> internal

locked ==> 0

unlocked ==> 1



Related functions -




Related options -



References -


Parameter name Attached Pseudo-Wires List

Abbreviated name attachedPWList

Table 321 attachedPWList (Attached Pseudo-Wires List)

374 DN70577885



PWTIP Parameters

39.3 pwTipId (Pseudowire Tunnel IP Identifier)

3GPP name -


Multiplicity 6

Description A list of all Pseudowires running through this tunnel.

Format: slot#-mp#, e.g. "1-5" with

slot#: always "1" in this release

mp#: 1..6

Range 3

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 321 attachedPWList (Attached Pseudo-Wires List) (Cont.)

Parameter name Pseudowire Tunnel IP Identifier

Abbreviated name pwTipId

3GPP name -


Multiplicity 1

Description Identifier for the Pseudowire Tunnel.

The value is fixed to 1-76.

Range 4

Table 322 pwTipId (Pseudowire Tunnel IP Identifier)

DN70577885 375

Flexi Transport Module Parameters PWTIP Parameters


39.4 remoteIpv4Addr (Remote IPv4 Address)

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 322 pwTipId (Pseudowire Tunnel IP Identifier) (Cont.)

Parameter name Remote IPv4 Address

Abbreviated name remoteIpv4Addr

3GPP name -


Multiplicity 1

Description This parameter shall define the IPv4 address of the remote PWE3 GW (RNC GW) where the PW is ter-minated. The address will range from 0.0.0.0 (7 characters) to 255.255.255.255 (15 characters)

Range 7...15

Step -

Units characters



Default value -


Related functions -

Table 323 remoteIpv4Addr (Remote IPv4 Address)

376 DN70577885



PWTIP Parameters




Related options -



References -

Table 323 remoteIpv4Addr (Remote IPv4 Address) (Cont.)

DN70577885 377

Flexi Transport Module Parameters QOS Parameters


40 QOS Parameters

40.1 perHopBehaviourWeightList (Per Hop Behaviour Weight List)

Parameter name Per Hop Behaviour Weight List

Abbreviated name perHopBehaviourWeightList

3GPP name -

Managed Object QOS

Multiplicity 1

Description This is a set of 5 weight values for the traffic queues associated to the Per Hop Behaviours:

- Assured Forwarding 4 (AF4)




- Best Effort (BE.

Weight value range is between 1 and 10.000.


-

Default value -


Related functions -

Child parameters – assuredForwardingClass1– assuredForwardingClass2– assuredForwardingClass3– assuredForwardingClass4– bestEffort







References -

Table 324 perHopBehaviourWeightList (Per Hop Behaviour Weight List)

378 DN70577885



QOS Parameters

40.2 assuredForwardingClass1 (Assured Forwarding Class 1 Weight Value)


Parameter name Assured Forwarding Class 1 Weight Value

Abbreviated name assuredForwardingClass1

3GPP name -

Managed Object -

Multiplicity 1

Description This is the weight value of the traffic queue associ-ated to the Per Hop Behaviour Assured Forwarding Class 1 (AF1).

Range 1... 10000

Step 1

Units -



Default value 10


Related functions -







References -

Table 325 assuredForwardingClass1 (Assured Forwarding Class 1 Weight Value)



3GPP name -

Managed Object -


DN70577885 379




Multiplicity 1


Range 1... 10000

Step 1

Units -



Default value 100


Related functions -







References -




3GPP name -

Managed Object -

Multiplicity 1


Range 1... 10000

Step 1

Units -


380 DN70577885



QOS Parameters




Default value 1000


Related functions -







References -




3GPP name -

Managed Object -

Multiplicity 1


Range 1... 10000

Step 1

Units -



Default value 10000


Related functions -



DN70577885 381



40.6 bestEffort (Best Effort Weight Value)






References -


Parameter name Best Effort Weight Value

Abbreviated name bestEffort

3GPP name -

Managed Object -

Multiplicity 1

Description This is the weight value of the traffic queue associ-ated to the Per Hop Behaviour Best Effort (BE).

Range 1... 10000

Step 1

Units -



Default value 1


Related functions -







References -

Table 329 bestEffort (Best Effort Weight Value)

382 DN70577885



QOS Parameters

40.7 qosId (Quality of Service Configuration Identifier)

40.8 trafficTypesMap (Quality of Service mapping table)

Parameter name Quality of Service Configuration Identifier

Abbreviated name qosId

3GPP name -

Managed Object QOS

Multiplicity 1

Description This parameter identifies the BTS transport Quality of Service (QOS) configuration. The value is always 1.

Range 1... 1

Step 1

Units -



Default value -


Related functions -







References -

Table 330 qosId (Quality of Service Configuration Identifier)

Parameter name Quality of Service mapping table

Abbreviated name trafficTypesMap

3GPP name -

Managed Object QOS

Multiplicity 35

Table 331 trafficTypesMap (Quality of Service mapping table)

DN70577885 383



40.9 dscpList (Differentiated Services Code Point list)

Description This table maps traffic types to Per Hop Behaviours and to other quality of service properties, including VlanId, VlanPrio and DSCP values.


-

Default value -


Related functions -

Child parameters – dscpList– pHB– trafficType– vlanPrio


Related parameters iHSPAmode of IPNO - In iHS-PAmode, QOS configuration supports the IubIp traffictypes.


Related options – RAN1253 Iub Transport QoS– RAN2440 Fast IP Rerouting



References -

Table 331 trafficTypesMap (Quality of Service mapping table) (Cont.)

Parameter name Differentiated Services Code Point list

Abbreviated name dscpList

3GPP name -

Managed Object -

Multiplicity 1

Description This is the list of Differentiated Services Code Point (DSCP) values that relate to a specific traffic cate-gory. The list is a comma-seperated value list. The values are DSCP decimal values. The list can contain up to 64 entries.

Range 0...255

Table 332 dscpList (Differentiated Services Code Point list)

384 DN70577885



QOS Parameters

40.10 pHB (Per Hop Behaviour)

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 332 dscpList (Differentiated Services Code Point list) (Cont.)

Parameter name Per Hop Behaviour

Abbreviated name pHB

3GPP name -

Managed Object -

Multiplicity 1

Description This parameter designates a Per Hop Behaviour.

The following values are predefined:

0 = EF (meaning: Expedited Forwarding)

1 = AF4 (Assured Forwarding 4)




5 = BE (Best Effort).

Table 333 pHB (Per Hop Behaviour)

DN70577885 385



40.11 trafficType (Traffic type)

Range expeditedForwarding (0), assuredForwardingClass4 (1), assuredForwardingClass3 (2), assuredForwardingClass2 (3), assuredForwardingClass1 (4), bestEffort (5)

Step -

Units -


gui ==> internal

expeditedForwarding ==> 0





bestEffort ==> 5

Default value -


Related functions -




Related options -



References -

Table 333 pHB (Per Hop Behaviour) (Cont.)

Parameter name Traffic type

Abbreviated name trafficType

3GPP name -

Managed Object -

Multiplicity 1

Table 334 trafficType (Traffic type)

386 DN70577885



QOS Parameters

Description This parameter designates a traffic type.

Values for transport mode AtmOverEthernet:

"TOP"

"SG1" - Pseudowire (PW) for perHopBehaviour (pHB) EF

"SG2" - PW for pHB AF4




"SG6" - PW for pHB BE

"ICMP"

Values for transport mode Iub IP:

"DCN"

"NBAP"

"TOP"

"SG1" - Signalled traffic for pHB EF

"SG2" - Signalled traffic for pHB AF4




"SG6" - Signalled traffic for pHB BE

"ICMP"

"CES1" to "CES4" - For mapping DSCP values to vlanPrio bits (on FIIB,FILB,FTIB,FTLB units only)

"CES1" to "CES8" - For mapping DSCP values to vlanPrio bits (on FTFB, FIIF, FTIF unit only)

"BFD1" to "BFD16"

"OSPF" (on FIIB,FILB,FTIA,FTIB,FTJA,FTLB,FTFB, FSM, FSI, FIIF, FTIF units only)

Values for transport mode Dual Iub:

"TOP"

"SG1" - Signalled traffic for pHB EF





"SG6" - Signalled traffic for pHB BE

"ICMP"

"BFD1" to "BFD16"

"OSPF" (on FIIB,FILB,FTIA,FTIB,FTJA,FTLB,FTFB, FIIF, FTIF units only)

DN70577885 387



40.12 vlanPrio (Vlan priority flag)

Range 1...40

Step -

Units characters



Default value -


Related functions -


Related parameters iHSPAmode of IPNO - Value "OSPF" is not supported if iHSPAmode is set to enabled.


Related options – AND RAN2440 Fast IP Rerouting (optional) AND RAN1879 Dynamic routing by OSPF (optional) AND RAN2359 OSPF enhance-ments (optional) AND RAN74 Native Iub IP for Flexi WCDMA BTS (optional) AND RAN1253 Iub Transport QoS (optional)



References -

Table 334 trafficType (Traffic type) (Cont.)

Parameter name Vlan priority flag

Abbreviated name vlanPrio

3GPP name -

Managed Object -

Multiplicity 1

Description This is the vlan priority to be used on all connec-tions for a given Per Hop Behaviour.

Range 0... 7

Step 1

Units -

Table 335 vlanPrio (Vlan priority flag)

388 DN70577885



QOS Parameters



Default value 0


Related functions -




Related options -



References -

Table 335 vlanPrio (Vlan priority flag) (Cont.)

DN70577885 389

Flexi Transport Module Parameters SDHIF Parameters


41 SDHIF Parameters




3GPP name -

Managed Object SDHIF

Multiplicity 1


Unlocking the interface triggers the creation of a TCTT (ATM interface).

Locking the interface deactivates it and all alarms and any ATM cell transfer is suppressed. Note that the associated TCTT (ATM interface) is not deleted.


Step -

Units -


gui ==> internal

locked ==> 0

unlocked ==> 1



Related functions -




Related options -

Feature dependencies – Physical Interfaces STM1/OC3 & STM0/OC1


References -


390 DN70577885



SDHIF Parameters


41.3 laserMode (Laser Mode)



3GPP name -


Multiplicity 1

Description Defines the interface location on the unit.

Since the FTOA unit provides just one SDH inter-face, the number is fixed to 1.

Range 1... 1

Step 1

Units -



Default value 1

Default value notes Fixed value 1.

Related functions -




Related options -



References -


Parameter name Laser Mode

Abbreviated name laserMode

3GPP name -


Multiplicity 1

Table 338 laserMode (Laser Mode)

DN70577885 391



41.4 rdiOnExcessiveBer (Remote Defect Indication On Exces-sive Bit Error Ratio)

Description Switches the laser on or off separately for each SDH interface. Automatic switching is not provided.

Range LASER_MODE_OFF (0), LASER_MODE_ON (1)

Step -

Units -


gui ==> internal

LASER_MODE_OFF ==> 0

LASER_MODE_ON ==> 1

Default value LASER_MODE_OFF (0)


Related functions -




Related options -



References -

Table 338 laserMode (Laser Mode) (Cont.)

Parameter name Remote Defect Indication On Excessive Bit Error Ratio

Abbreviated name rdiOnExcessiveBer

3GPP name -


Multiplicity 1

Description Enables or disables RDI on EBER that is set in SDH/SONET frame if the Bit Error Ratio of the con-nection is exceeded.


Step -

Table 339 rdiOnExcessiveBer (Remote Defect Indication On Excessive Bit Error Ratio)

392 DN70577885



SDHIF Parameters

41.5 sdhifId (SDH Interface Identifier)

Units -


– false => 0 – true => 1



Related functions -




Related options -



References -

Table 339 rdiOnExcessiveBer (Remote Defect Indication On Excessive Bit Error Ratio) (Cont.)

Parameter name SDH Interface Identifier

Abbreviated name sdhifId

3GPP name -


Multiplicity 1

Description This MO class has only one instance in this release. The identifier is "1-1"

(unit#-if#)

Range 3

Step -

Units characters



Default value 1-1

Default value notes Value is always "1-1. In this release only one unit with at most one SDH interface is available.

Related functions -

Table 340 sdhifId (SDH Interface Identifier)

DN70577885 393







Related options -



References -

Table 340 sdhifId (SDH Interface Identifier) (Cont.)



3GPP name -


Multiplicity 1


Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -




394 DN70577885



SDHIF Parameters

41.7 xmtTraceId_HP (Sent Trace Identifier (J1, HOP))

41.8 xmtTraceId_RS (Sent Trace Identifier (J0, RS))

References -


Parameter name Sent Trace Identifier (J1, HOP)

Abbreviated name xmtTraceId_HP

3GPP name -


Multiplicity 1

Description Specifies a signal label forwarded to the remote site on the High Order Path. The Trace Identifier is located in the J1 byte of the RSOH in the STM/SONET frame.

Range 0...15

Step -

Units characters



Default value -

Default value notes The empty string is default value and indicates that the feature is not used.

Related functions -




Related options -



References -

Table 342 xmtTraceId_HP (Sent Trace Identifier (J1, HOP))

Parameter name Sent Trace Identifier (J0, RS)

Table 343 xmtTraceId_RS (Sent Trace Identifier (J0, RS))

DN70577885 395



Abbreviated name xmtTraceId_RS

3GPP name -


Multiplicity 1

Description Specifies a signal label forwarded to the remote site. The Trace Identifier is located in the J0 byte of the RSOH in the STM-1 frame. It is not supported on SONET interfaces.

As a default, no value is defined. In this case the Trace Identifier is not checked in the FTM.

Range 0...15

Step -

Units characters



Default value -

Default value notes The empty string is default value and indicates that the feature is not used.

Related functions -




Related options -



References -

Table 343 xmtTraceId_RS (Sent Trace Identifier (J0, RS)) (Cont.)

396 DN70577885



STPG Parameters

42 STPG Parameters

42.1 ssmSelExt2M (SSM Selection with external 2.048 MHz)

Parameter name SSM Selection with external 2.048 MHz

Abbreviated name ssmSelExt2M

3GPP name -

Managed Object STPG

Multiplicity 1

Description This parameter is used for selection with external 2.048 MHz being sync reference.

Range PRC (0), SSU-A (1), SSU-B (2), EEC1 (3), PRS (4), Stratum2 (5), TraceabilityUnknown (6)

Step -

Units -


gui ==> internal

PRC ==> 0

SSU-A ==> 1

SSU-B ==> 2

EEC1 ==> 3

PRS ==> 4

Stratum2 ==> 5

TraceabilityUnknown ==> 6

Default value EEC1 (3)

Default value notes The default value in ITU is EEC1 and ANSI is "Traceability Unknown".

Related functions -




Related options -


Interfaces – EM <-> FTM– FTM <-> RAC– RAC <-> RACApp

References NSN reference: CN4429 SyncE alignment to SSM acceptance level

Table 344 ssmSelExt2M (SSM Selection with external 2.048 MHz)

DN70577885 397

Flexi Transport Module Parameters STPG Parameters


42.2 ssmSelPDH (SSM Selection with TDM)

Parameter name SSM Selection with TDM

Abbreviated name ssmSelPDH

3GPP name -

Managed Object STPG

Multiplicity 1

Description This parameter is used for selection of SSM with TDM being sync reference.


Step -

Units -


gui ==> internal

PRC ==> 0

SSU-A ==> 1

SSU-B ==> 2

EEC1 ==> 3

PRS ==> 4

Stratum2 ==> 5




Related functions -




Related options -




Table 345 ssmSelPDH (SSM Selection with TDM)

398 DN70577885



STPG Parameters

42.3 ssmSelSyncE (SSM Selection with SyncE)

Parameter name SSM Selection with SyncE

Abbreviated name ssmSelSyncE

3GPP name -

Managed Object STPG

Multiplicity 1

Description This parameter is used for selection with SyncE being sync reference and SSM monitoring.


Step -

Units -


gui ==> internal

PRC ==> 0

SSU-A ==> 1

SSU-B ==> 2

EEC1 ==> 3

PRS ==> 4

Stratum2 ==> 5




Related functions -




Related options -




Table 346 ssmSelSyncE (SSM Selection with SyncE)

DN70577885 399



42.4 ssmTxUntagged (Send SSM message frames untagged)

42.5 ssmType (SSM support network standard)

Parameter name Send SSM message frames untagged

Abbreviated name ssmTxUntagged

3GPP name -

Managed Object STPG

Multiplicity 1

Description If true, the frames of SSM messages transmitted for Synchronous Ethernet are mandatory untagged, even when sent on VLAN interfaces.


Step -

Units -


– false => 0 – true => 1


Default value notes By default the frames are untagged.

Related functions -







References -

Table 347 ssmTxUntagged (Send SSM message frames untagged)

Parameter name SSM support network standard

Abbreviated name ssmType

3GPP name -

Managed Object STPG

Multiplicity 1

Table 348 ssmType (SSM support network standard)

400 DN70577885



STPG Parameters

42.6 synchERegenOn (Activate the synchronous ethernet regenerator function)

Description This parameter specifies according to which network standard SSM messages shall be transmit-ted in synchronous Ethernet regeneration mode.

Range SSM_OFF (1), SSM_ITU (2), SSM_ANSI (3)

Step -

Units -


gui ==> internal

SSM_OFF ==> 1

SSM_ITU ==> 2

SSM_ANSI ==> 3

Default value SSM_ITU (2)

Default value notes Default is ITU / ETSI standard.

Related functions -







References -

Table 348 ssmType (SSM support network standard) (Cont.)

Parameter name Activate the synchronous ethernet regenerator function

Abbreviated name synchERegenOn

3GPP name -

Managed Object STPG

Multiplicity 1

Description This parameter switches the Synchronous Ethernet Regenerator function on.


Table 349 synchERegenOn (Activate the synchronous ethernet regenerator function)

DN70577885 401



42.7 synchroSourceList (The synchronization sources of the BTS)

Step -

Units -


– false => 0 – true => 1


Default value notes By default the function is switched off.

Related functions -







References -

Table 349 synchERegenOn (Activate the synchronous ethernet regenerator function) (Cont.)

Parameter name The synchronization sources of the BTS

Abbreviated name synchroSourceList

3GPP name -

Managed Object STPG

Multiplicity 2

Description This is the list of synchronization sources of the BTS. Up to 2 clock sources can be configured.


-

Default value -


Related functions -

Table 350 synchroSourceList (The synchronization sources of the BTS)

402 DN70577885



STPG Parameters

42.8 clockProtocol (Protocol of the clock source)

Child parameters – clockProtocol– interfaceNumber– priority– ssmAcceptanceLevel– ssmEnabled– ssmTimeout– unitNumber




Related options – RAN1254 Timing over Packet– RAN1708 Synchronuous Ethernet



References -

Table 350 synchroSourceList (The synchronization sources of the BTS) (Cont.)

Parameter name Protocol of the clock source

Abbreviated name clockProtocol

3GPP name -

Managed Object -

Multiplicity 1

Description This parameter holds the protocol of this clock source: PDH, SDH, synchronuous Ethernet, Timing over Packet or the external 2 MHz clock.

Range clkPDH (1), clkSDH (2), clkSyncE (3), clkToP (4), clkExt (5)

Step -

Units -

Table 351 clockProtocol (Protocol of the clock source)

DN70577885 403



42.9 interfaceNumber (Interface number)


gui ==> internal

clkPDH ==> 1

clkSDH ==> 2

clkSyncE ==> 3

clkToP ==> 4

clkExt ==> 5

Default value -


Related functions -







References -

Table 351 clockProtocol (Protocol of the clock source) (Cont.)

Parameter name Interface number


3GPP name -

Managed Object -

Multiplicity 1

Table 352 interfaceNumber (Interface number)

404 DN70577885



STPG Parameters

Description This parameter specifies either

- the PDH interface on the unit for a PDH synchro-nization source, or

- the SDH interface on the unit for a SDH clock source, or

- the Ethernet interface on the unit for the synchro-nous Ethernet synchronization source.

In case of Timing over Packet the BTS automati-cally selects the Ethernet link. This parameter is ignored.

In case the external clock is selected as synchroni-zation source the parameter is ignored by the BTS. Recommended value is 0 in this case.

Examples:

interfaceNumber=1, unitNumber=1, clockProto-col=clkPDH: This means PDH interface number 1 on unit 1.

interfaceNumber=1, unitNumber=1, clockProto-col=clkSyncE: This means Ethernet interface number 1 on unit 1.

Range 0... 16

Step 1

Units -



Default value -


Related functions -







References -

Table 352 interfaceNumber (Interface number) (Cont.)

DN70577885 405



42.10 priority (Clock source priority)

42.11 ssmAcceptanceLevel (SSM defined value)

Parameter name Clock source priority

Abbreviated name priority

3GPP name -

Managed Object -

Multiplicity 1

Description This parameter holds the priority in which the clock sources of the BTS are to be taken into use. Value 1 ist highest priority: this clock source will be taken first.

Range 1... 2

Step 1

Units -



Default value -


Related functions -







References -

Table 353 priority (Clock source priority)

Parameter name SSM defined value

Abbreviated name ssmAcceptanceLevel

3GPP name -

Managed Object -

Table 354 ssmAcceptanceLevel (SSM defined value)

406 DN70577885



STPG Parameters

42.12 ssmEnabled (SSM enabling flag)

Multiplicity 1

Description This is the defined SSM value (defined quality of the source clock). An alarm will be raised, If the quality falls below this value for ssmTimeout seconds.

Range ssmPRCorPRS (1), ssmSSU (2)

Step -

Units -


gui ==> internal

ssmPRCorPRS ==> 1

ssmSSU ==> 2

Default value -


Related functions -


Related parameters clockProtocol of STPG - This parameter is only relevant in case the value of parameter clockProtocol is equal to clkSyncE (Syn-chronuous Ethernet clock source).

ssmTimeout of STPG - An alarm is raised if the observed quality of clock source is below ssmAcceptanceLevel for a period of ssm-Timeout seconds.


Related options – RAN1708 Synchronuous Ethernet



References -

Table 354 ssmAcceptanceLevel (SSM defined value) (Cont.)

Parameter name SSM enabling flag

Abbreviated name ssmEnabled

3GPP name -

Managed Object -

Multiplicity 1

Table 355 ssmEnabled (SSM enabling flag)

DN70577885 407



42.13 ssmTimeout (SSM message timeout)

Description This parameter enables Synchronization Status Message (SSM) support for Synchronuous Ether-net.


Step -

Units -


– false => 0 – true => 1


Default value notes By default SSM support is enabled.

Related functions -







References -

Table 355 ssmEnabled (SSM enabling flag) (Cont.)

Parameter name SSM message timeout

Abbreviated name ssmTimeout

3GPP name -

Managed Object -

Multiplicity 1

Table 356 ssmTimeout (SSM message timeout)

408 DN70577885



STPG Parameters

42.14 unitNumber (Unit number)

Description This is the maximum duration in seconds for which the actual SSM value may be less than a required clock quality. If the duration is surpassed, an alarm will be raised.

If SSM support is according to network standard ITU / ETSI, an alarm will be raised if the observed SSM value falls below ssmPRC quality for ssmTim-eout seconds.

If SSM support is according to network standard ANSI / SONET, an alarm will be raised if the observed SSM value falls below ssmPRS quality for ssmTimeout seconds.

Range 2... 10

Step 1

Units seconds



Default value 5


Related functions -







References -

Table 356 ssmTimeout (SSM message timeout) (Cont.)

Parameter name Unit number


3GPP name -

Table 357 unitNumber (Unit number)

DN70577885 409



42.15 timingGenPgId (Synchronisation Protection Group Identi-fier)

Managed Object -

Multiplicity 1

Description This parameter specifies the location of the unit providing the synchronisation source interface. unitNumber shall be "0" for ToP sync source when unit is FSM/FSI/FTIF/FIIF.

Range 1 ... 1 for WN7.0 1.0;

0... 1 for WN7.0 2.0

Step 1

Units -



Default value -


Related functions -







References -

Table 357 unitNumber (Unit number) (Cont.)

Parameter name Synchronisation Protection Group Identifier

Abbreviated name timingGenPgId

3GPP name -

Managed Object STPG

Multiplicity 1

Table 358 timingGenPgId (Synchronisation Protection Group Identifier)

410 DN70577885



STPG Parameters

Description This parameter identifies the BTS transport syn-chronisation protection group. The value is always 1.

Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 358 timingGenPgId (Synchronisation Protection Group Identifier) (Cont.)

DN70577885 411

Flexi Transport Module Parameters SYNC Parameters


43 SYNC Parameters

43.1 syncId (Clock Synchronization Configuration Identifier)

Parameter name Clock Synchronization Configuration Identifier

Abbreviated name syncId

3GPP name -

Managed Object SYNC

Multiplicity 1

Description This parameter identifies the BTS transport clock synchronization configuration. The value is always 1.

Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 359 syncId (Clock Synchronization Configuration Identifier)

412 DN70577885



TCTT Parameters

44 TCTT Parameters

44.1 interfaceNumber (Interface number)

Parameter name Interface number


3GPP name -

Managed Object TCTT

Multiplicity 1








Range 1... 76

Step 1

Units -



Default value -


Related functions -


Related parameters imaGroupId of IMAG

Parameter relationships If the TC adapter is associated to an IMA group, the imaGroupId is used as interface number

Related options -



References -

Table 360 interfaceNumber (Interface number)

DN70577885 413

Flexi Transport Module Parameters TCTT Parameters


44.2 tcAdaptorTTPId (ATM Interface Identifier)

Parameter name ATM Interface Identifier

Abbreviated name tcAdaptorTTPId

3GPP name -

Managed Object TCTT

Multiplicity 1

Description Naming attribute


- Interface Type (PPTT, IMAG, PWTIP, SVTT)

- UnitNumber (always "1")

- InterfaceNumber (if#, must be equal to the attri-bute interfaceNumber)

Format:

- PPTT-1-if#

- IMAG-1-if#

- PWTIP-1-76

- SVTT-1-1

Range 8...10

Step -

Units characters



Default value -


Related functions -


Related parameters interfaceNumber of TCTT - The value of the attribute interfaceNumber is contained in the ATM interface identifier.


Related options -



References -

Table 361 tcAdaptorTTPId (ATM Interface Identifier)

414 DN70577885



TCTT Parameters




3GPP name -

Managed Object TCTT

Multiplicity 1


Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -



References -


DN70577885 415

Flexi Transport Module Parameters TMPAR Parameters


45 TMPAR Parameters

45.1 cacCommittedBitRate (CAC Committed Bit Rate)

Parameter name CAC Committed Bit Rate

Abbreviated name cacCommittedBitRate

3GPP name -

Managed Object TMPAR

Multiplicity 1

Table 363 cacCommittedBitRate (CAC Committed Bit Rate)

416 DN70577885



TMPAR Parameters

Description Connection Admission Control Committed Bit Rate

- Used in Dual Iub and Iub/IP transport modes

In case there is just one IP interface (IVIF, IEIF, P3xL) or when shaping is WFQ (IEIF/trafficPath-ShapingEnable) CAC committed bit rate is a total bit rate, which is available for guaranteed traffic at the Iub. In Iub/IP mode (not in dual Iub mode) sig-nalling bit rate and DCN bit rate are subtracted from the CAC committed bit rate and the rest is available for the user-plane data connections which are under transport connection admission control.

If there are several IP interfaces and shaping is PATH, Connection Admission Control is based on CIR parameter of the IP interface (IVIF, IEIF) that user plane uses.

The value range depends on the network interface type.

Fast Ethernet: 400 Kbps to 99900 Kbps with step of 100 Kbps

Gigabit Eth: 400 Kbps to 999900 Kbps with step of 100 Kbps

Multi Link PPP (P3ML): Connection Admission Control is based on the summed capacity of the PPP links included. CAC Committed bit rate param-eter value is omitted in this case. Signalling bit rate and DCN bit rate are subtracted from the PPP link capacity and the rest is available for the user-plane data connections which are under transport con-nection admission control.

Single Link PPP (P3SL): Connection Admission Control is based on the capacity of the PPP link included. CAC Committed bit rate parameter value is omitted in this case. Signalling bit rate and DCN bit rate are subtracted from the PPP link capacity and the rest is available for the user-plane data con-nections which are under transport connection admission control.

Range 400... 999900

Step 100

Units kbps



Default value -


Table 363 cacCommittedBitRate (CAC Committed Bit Rate) (Cont.)

DN70577885 417



45.2 dcnCommittedBitRate (DCN Committed Bit Rate)

Related functions -


Related parameters transportMode of IPNO

Parameter relationships cacCommittedBitRate is relevant only for transport modes Dual Iub and Iub/IP.

Related options – RAN1449 Dual Iub for Flexi WCDMA– RAN74 Native Iub IP for Flexi WCDMA BTS



References -

Table 363 cacCommittedBitRate (CAC Committed Bit Rate) (Cont.)

Parameter name DCN Committed Bit Rate

Abbreviated name dcnCommittedBitRate

3GPP name -


Multiplicity 1

Description DCN Committed Bit Rate. Used in transport mode Iub/IP.

Range 50... 1000

Step 50

Units kbps



Default value 150


Related functions -



Parameter relationships dcnCommitttedBitRate is only relevant for transport mode Iub/IP.

Related options – RAN74 Native Iub IP for Flexi WCDMA BTS


Table 364 dcnCommittedBitRate (DCN Committed Bit Rate)

418 DN70577885



TMPAR Parameters

45.3 externalNATIpAddress (External NAT IP Address)


References -

Table 364 dcnCommittedBitRate (DCN Committed Bit Rate) (Cont.)

Parameter name External NAT IP Address

Abbreviated name externalNATIpAddress

3GPP name -


Multiplicity 1

Description This is the IP address to be used in addressing the external NAT device.

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options – RAN1449 Dual Iub for Flexi WCDMA



References -

Table 365 externalNATIpAddress (External NAT IP Address)

DN70577885 419



45.4 farEndSctpSubnetIpAddress (Far End SCTP Subnet IP Address )

Parameter name Far End SCTP Subnet IP Address

Abbreviated name farEndSctpSubnetIpAddress

3GPP name -


Multiplicity 1

Description This is the IP address to be used in the transport network at the far end of the SCTP tunnel. The address is the SCTP tunnel subnet address, i.e all its host bits must be set to 0´s. It must be entered in dotted decimal format.

The parameter is used in Iub/IP transport mode.

The associated subnet mask is defined in parame-ter farEndSctpSubnetMask.

Range 7...15

Step -

Units characters



Default value -


Related functions -



Parameter relationships farEndSctpSubnetIpAddress is only relevant in transportMode Iub/IP.




References -

Table 366 farEndSctpSubnetIpAddress (Far End SCTP Subnet IP Address )

420 DN70577885



TMPAR Parameters

45.5 farEndSctpSubnetMask (Far End SCTP Subnet Mask)

45.6 minSCTPPort (Minimum SCTP port number)

Parameter name Far End SCTP Subnet Mask

Abbreviated name farEndSctpSubnetMask

3GPP name -


Multiplicity 1

Description This is the subnet mask for the far end SCTP tunnel subnet IP address (parameter farEndSctpSubnetI-pAddress). To be entered in dotted decimal format.

Range 7...15

Step -

Units characters



Default value -


Related functions -



Parameter relationships The farEndSctpSubnetMask is only relevant in transport mode Iub/IP.




References -

Table 367 farEndSctpSubnetMask (Far End SCTP Subnet Mask)

Parameter name Minimum SCTP port number

Abbreviated name minSCTPPort

3GPP name -


Multiplicity 1

Table 368 minSCTPPort (Minimum SCTP port number)

DN70577885 421



45.7 minUDPPort (Minimum UDP port number)

Description This is is the minimum value of the port number to be used for SCTP. Used in transport mode Iub/IP.

Range 49152... 65534

Step 1

Units -



Default value 49152


Related functions -



Parameter relationships minSCTPPort is only relevant in transport mode Iub/IP.




References -

Table 368 minSCTPPort (Minimum SCTP port number) (Cont.)

Parameter name Minimum UDP port number

Abbreviated name minUDPPort

3GPP name -


Multiplicity 1

Description This is is the minimum value of the port number to be used for UDP connections.

The maximum value of this parameter = 63047, since 2488 calls are supported in transport modes Dual Iub an IubIP (65535 - 2488 = 63047).

Range 49152... 63047

Step 1

Units -

Table 369 minUDPPort (Minimum UDP port number)

422 DN70577885



TMPAR Parameters

45.8 signallingCommittedBitRate (Signalling Committed Bit Rate)



Default value 49152


Related functions -







References -

Table 369 minUDPPort (Minimum UDP port number) (Cont.)

Parameter name Signalling Committed Bit Rate

Abbreviated name signallingCommittedBitRate

3GPP name -


Multiplicity 1

Description Signalling Committed Bit Rate. Used in transport mode Iub/IP.

Range 50... 1000

Step 50

Units kbps



Default value 100


Related functions -


Table 370 signallingCommittedBitRate (Signalling Committed Bit Rate)

DN70577885 423



45.9 tmparId (TMPAR Object Instance Identifier)


Parameter relationships signallingCommittedBitRate is only relevant for transport mode Iub/IP.




References -

Table 370 signallingCommittedBitRate (Signalling Committed Bit Rate) (Cont.)

Parameter name TMPAR Object Instance Identifier

Abbreviated name tmparId

3GPP name -


Multiplicity 1

Description This parameter identifies the unique object instance of the TMPAR clas. Value is always 1.

Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -



Table 371 tmparId (TMPAR Object Instance Identifier)

424 DN70577885



TMPAR Parameters

References -

Table 371 tmparId (TMPAR Object Instance Identifier) (Cont.)

DN70577885 425

Flexi Transport Module Parameters TOPIK Parameters


46 TOPIK Parameters


46.2 logMeanSyncValue (Log mean synchronization value)



3GPP name -

Managed Object TOPIK

Multiplicity 1

Description Used to lock and unlock the TOP object instance.

Locking the object deactivates it and supresses all its alarms.


Step -

Units -


gui ==> internal

locked ==> 0

unlocked ==> 1



Related functions -




Related options – RAN1254 Timing over Packet



References -


Parameter name Log mean synchronization value

Abbreviated name logMeanSyncValue

Table 373 logMeanSyncValue (Log mean synchronization value)

426 DN70577885



TOPIK Parameters

46.3 masterIpAddr (IP Address of the ToP master)

3GPP name -


Multiplicity 1

Description This indicates how often a ToP sync message shall be send by the ToP master within the transmission duration request period. (The transmission duration request period is currently fixed to 300 seconds.)

The following values are defined:

-3: 8 per second

-4: 16 per second

-5: 32 per second

Range -5... -3

Step 1

Units -



Default value -4

Default value notes This means 16 per second.

Related functions -







References -

Table 373 logMeanSyncValue (Log mean synchronization value) (Cont.)

Parameter name IP Address of the ToP master

Abbreviated name masterIpAddr

3GPP name -


Multiplicity 1

Table 374 masterIpAddr (IP Address of the ToP master)

DN70577885 427

Flexi Transport Module Parameters TOPIK Parameters


46.4 topId (Timing Over Packet Configuration Identifier)

Description IP address of the ToP master. To be entered in dotted format.

Range 7...15

Step -

Units characters



Default value -


Related functions -


Related parameters administrativeState of TOPIK

Parameter relationships The parameter masterIpAddr shall have a regular value (not NULL, not 0.0.0.0, etc). whenever parameter administrativeState is set to unlocked.




References -

Table 374 masterIpAddr (IP Address of the ToP master) (Cont.)

Parameter name Timing Over Packet Configuration Identifier

Abbreviated name topId

3GPP name -


Multiplicity 1

Description This parameter identifies the BTS Timing over Packet (TOP) configuration. The value is always 1.

Range 1... 1

Step 1

Units -



Table 375 topId (Timing Over Packet Configuration Identifier)

428 DN70577885



TOPIK Parameters

Default value -


Related functions -







References -

Table 375 topId (Timing Over Packet Configuration Identifier) (Cont.)

DN70577885 429

Flexi Transport Module Parameters TRDE Parameters


47 TRDE Parameters

47.1 atmTrafficDescriptorId (Traffic Descriptor Identifier)

47.2 conformanceDefinition (Conformance Definition)

Parameter name Traffic Descriptor Identifier

Abbreviated name atmTrafficDescriptorId

3GPP name -

Managed Object TRDE

Multiplicity 1

Description This parameter identifies the traffic descriptor.

The value of the parameter shall represent a number starting with 100. Note that at most 32 traffic descriptors can exist in the AXC.

Range 3...10

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 376 atmTrafficDescriptorId (Traffic Descriptor Identifier)

Parameter name Conformance Definition

Abbreviated name conformanceDefinition

Table 377 conformanceDefinition (Conformance Definition)

430 DN70577885



TRDE Parameters

47.3 minDesiredCellRate (Minimum Desired Cell Rate)

3GPP name -

Managed Object TRDE

Multiplicity 1

Description Specifies the type of conformance test performed on the traffic stream by Usage Parameter Control (UPC).

The FTM enforces the correspondence between conformance definition and service category. For CBR the conformance definition is CBR.1 and for UBR UBR.1.

Range CBR1 (0), UBR1 (1)

Step -

Units -


gui ==> internal

CBR1 ==> 0

UBR1 ==> 1

Default value -

Default value notes Default values for service categories:CBR: CBR.1UBR: UBR.1

Related functions -




Related options -



References -

Table 377 conformanceDefinition (Conformance Definition) (Cont.)

Parameter name Minimum Desired Cell Rate

Abbreviated name minDesiredCellRate

3GPP name -

Table 378 minDesiredCellRate (Minimum Desired Cell Rate)

DN70577885 431



47.4 peakCellRate (Peak Cell Rate)

Managed Object TRDE

Multiplicity 1

Description Minimum Desired Cell Rate (MDCR). Is the targeted minimum throughput of a UBR connection in cells per second. The parameter can be set optionally for UBR connections. The same value applies both for ingress and egress traffic.

Note: The value of the MDCR cannot exceed the PCR.

Range 0... 144896

Step 1

Units cells/s



Default value 0


Related functions -


Related parameters peakCellRate of TRDE

Parameter relationships The value of the MDCR cannot exceed the PCR.

Related options -



References -

Table 378 minDesiredCellRate (Minimum Desired Cell Rate) (Cont.)

Parameter name Peak Cell Rate

Abbreviated name peakCellRate

3GPP name -

Managed Object TRDE

Multiplicity 1

Table 379 peakCellRate (Peak Cell Rate)

432 DN70577885



TRDE Parameters

47.5 ubrShare (UBR Share)

Description Specifies the peak cell rate (PCR) assigned or reserved in both egress and ingress directions of transmission across the VP or VC link that is termi-nated.

The rate is given in cells per seconds. It cannot be greater than the line rate of the source.

The exact allowed value range depends on the type of interface (E1, T1, SDH, IMA, ATMOverEthernet)

Range 36... 144896

Step 1

Units cells/s



Default value -


Related functions -




Related options -



References -

Table 379 peakCellRate (Peak Cell Rate) (Cont.)

Parameter name UBR Share

Abbreviated name ubrShare

3GPP name -

Managed Object TRDE

Multiplicity 1

Table 380 ubrShare (UBR Share)

DN70577885 433




Description UBRshare allows to weight the traffic exceeding the Minim Desired Cell Rate among UBR connections that share the same ATM interface. An individual UBR connection may get at least the ingress MDCR and up to ingress MDCR + ingressUBRshare_i / Sum(ingress UBRshare_i) * ingress EBW. Where ingres EBW is the currently available ingress band-width for the traffic of all the UBR connections sharing the same ATM interface.

The value of UBR Share applies to both ingress and egress traffic.

Range 1... 1000

Step 1

Units none



Default value 1


Related functions -




Related options -



References -

Table 380 ubrShare (UBR Share) (Cont.)



3GPP name -

Managed Object TRDE

Multiplicity 1


434 DN70577885



TRDE Parameters

Description A string used as label to describe the ATM traffic descriptor.

Range 1...20

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 381 userLabel (User Label) (Cont.)

DN70577885 435

Flexi Transport Module Parameters TWAMP Parameters


48 TWAMP Parameters

48.1 administrativeState (Lock or unlock a TWAMP session)

Parameter name Lock or unlock a TWAMP session


3GPP name -

Managed Object TWAMP

Multiplicity 1

Description This parameter locks or unlocks the TWAMP session. Locking a session stops it. Unlocking a session starts or re-starts it.

Starting or re-starting a session clears all statistics and alarms for the session. Stopping a session clears TWAMP alarms but not TWAMP statistics.


Step -

Units -


gui ==> internal

locked ==> 0

unlocked ==> 1


Default value notes By default the TWAMP session is locked.

Related functions -







References -

Table 382 administrativeState (Lock or unlock a TWAMP session)

436 DN70577885



TWAMP Parameters

48.2 destIpAddress (TWAMP session destination IP address)

Parameter name TWAMP session destination IP address

Abbreviated name destIpAddress

3GPP name -


Multiplicity 1

Description This parameter specifies the destination IP address of the TWAMP session. The TWAMP session must be locked, before its destination IP address can be changed.

Range 7...15

Step -

Units characters



Default value -


Related functions -

Modification Requires object locking


administrativeState of TWAMP - The TWAMP session must be locked, before its destination IP address can be changed (set admin-istrativeState to "locked").





References -

Table 383 destIpAddress (TWAMP session destination IP address)

DN70577885 437



48.3 destPort (TWAMP session destination port)

48.4 dscp (DSCP value for TWAMP message transmission)

Parameter name TWAMP session destination port

Abbreviated name destPort

3GPP name -


Multiplicity 1

Description This parameter specifies the destination port for TWAMP initiator messages. Changeing the desti-nation port of the TWAMP session requires locking the session.

Range 1... 65535

Step 1

Units -



Default value 5000


Related functions -

Modification Requires object locking


administrativeState of TWAMP - Changeing the destination port of the session requires locking it.





References -

Table 384 destPort (TWAMP session destination port)

Parameter name DSCP value for TWAMP message transmission

Table 385 dscp (DSCP value for TWAMP message transmission)

438 DN70577885



TWAMP Parameters

48.5 messageSize (TWAMP initiator message size)


3GPP name -


Multiplicity 1

Description This parameter specifies the DSCP value to be used for transmission of TWAMP messages over the session. The corresponding mapping to a Per Hop Behaviour priority queue is contained in table trafficTypesMap of the QOS managed object class.

Range 0... 63

Step 1

Units -



Default value 34

Default value notes The default DSCP value maps to Per Hop Behav-iour Assured Forwarding Class 4 (AF4).

Related functions -







References -

Table 385 dscp (DSCP value for TWAMP message transmission) (Cont.)

Parameter name TWAMP initiator message size

Abbreviated name messageSize

3GPP name -


Multiplicity 1

Table 386 messageSize (TWAMP initiator message size)

DN70577885 439



48.6 plrAlarmThreshold (Packet loss ratio alarm threshold)

Description This parameter specifies the size of the TWAMP messages sent by the TWAMP initiator on this session. The value of the parameter shall not exceed the Maximum Transfer Unit value of the FTM.

Range 69... 1400

Step 1

Units -



Default value 100


Related functions -



mtu of IPNO - The value of the parameter messageSize shall not exceed the Maximum Transfer Unit value of the FTM.





References -

Table 386 messageSize (TWAMP initiator message size) (Cont.)

Parameter name Packet loss ratio alarm threshold

Abbreviated name plrAlarmThreshold

3GPP name -


Multiplicity 1

Table 387 plrAlarmThreshold (Packet loss ratio alarm threshold)

440 DN70577885



TWAMP Parameters

48.7 rttAlarmThreshold (Round-trip-time alarm threshold)

Description This parameter specifies the threshold for raising the TWAMP session alarm for reasons of excessive packet loss ratio (PRL).

The alarm is raised, if the packet loss ratio observed over a 15 minute evalutation period exceeds the threshold value. The alarm will be cleared if the packet loss ratio drops below the threshold value for 2 consecutive 15-minute obser-vation periods.

Range 0... 10000

Step 1

Units 0.01%



Default value 10000

Default value notes Default value is 100 percent. This means the alarm is only raised if packet loss = 100%.

Related functions -







References -

Table 387 plrAlarmThreshold (Packet loss ratio alarm threshold) (Cont.)

Parameter name Round-trip-time alarm threshold

Abbreviated name rttAlarmThreshold

3GPP name -


Multiplicity 1

Table 388 rttAlarmThreshold (Round-trip-time alarm threshold)

DN70577885 441



48.8 sourceIpAddress (TWAMP initiator messages source IP address)

Description This parameter specifies the threshold for raising the TWAMP session alarm for reasons of excessive round-trip-time (RTT).

The alarm is raised if the average round-trip-time of the TWAMP messages, calculated during a 1-minute evaluation period, exceeds the configured threshold. The alarm will be cleared, if during 5 con-secutive 1-minute periods the average value of the RTT remains below the threshold.

Range 0... 1000000

Step 100

Units microseconds




Default value notes Default value is 1 second.

Related functions -







References -

Table 388 rttAlarmThreshold (Round-trip-time alarm threshold) (Cont.)

Parameter name TWAMP initiator messages source IP address

Abbreviated name sourceIpAddress

3GPP name -


Multiplicity 1

Table 389 sourceIpAddress (TWAMP initiator messages source IP address)

442 DN70577885



TWAMP Parameters

48.9 twampId (TWAMP session identifier)

Description This parameter specifies the source IP address of TWAMP initiator messages. The TWAMP session must be locked, before its source IP address can be changed.

Range 7...15

Step -

Units characters



Default value -


Related functions -



administrativeState of TWAMP - The TWAMP session must be locked, before its source IP address can be changed (set administra-tiveState to "locked").





References -

Table 389 sourceIpAddress (TWAMP initiator messages source IP address) (Cont.)

Parameter name TWAMP session identifier

Abbreviated name twampId

3GPP name -


Multiplicity 1

Description This parameter identifies a TWAMP session.

Range 1... 10

Table 390 twampId (TWAMP session identifier)

DN70577885 443



Step 1

Units -



Default value -


Related functions -







References -

Table 390 twampId (TWAMP session identifier) (Cont.)

444 DN70577885



UNIT Parameters

49 UNIT Parameters

49.1 enableRP301Interface (Enable RP3-01 interface)

49.2 unitId (Unit Identifier)

Parameter name Enable RP3-01 interface

Abbreviated name enableRP301Interface

3GPP name -

Managed Object UNIT

Multiplicity 1


Configure and designate EIF2(Out-door)/EIF5(Indoor) on the Flexi System Module (FCT) as RP3-01 interface


Step -

Units -


– false => 0 – true => 1



Related functions -


Related parameters unitTypeExpected of UNIT - This parameter is applicable only when unitTypeEx-pected is one of FTIF, FIIF, FSM, or FSI.


Related options -



References -

Table 391 enableRP301Interface (Enable RP3-01 interface)

Parameter name Unit Identifier

Table 392 unitId (Unit Identifier)

DN70577885 445

Flexi Transport Module Parameters UNIT Parameters


49.3 unitTypeActual (Installed hardware unit type)

Abbreviated name unitId

3GPP name -

Managed Object UNIT

Multiplicity 1

Description This parameter identifies the unit location as the slot number containing the hardware unit of BTS transport.

Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 392 unitId (Unit Identifier) (Cont.)

Parameter name Installed hardware unit type

Abbreviated name unitTypeActual

3GPP name -

Managed Object UNIT

Multiplicity 1

Table 393 unitTypeActual (Installed hardware unit type)

446 DN70577885



UNIT Parameters

Description This parameter shows the type of the hardware unit that is installed in the FTM slot.

Values are:

System Module Release 2:

FIIB: 472271A

FILB: 472294A

FTEB: 470156A

FTFA: 470134A

FTFB: 472036A

FTHA: 471522A

FTIA: 471025A

FTIB: 471720A

FTJA: 471248A

FTLB: 471984A

FTOA: 470133A

FTPB: 470137A


FSM: Outdoor System Module

FSI: Indoor System Module

FTIF: 472311A

FIIF: 472355A

Flexi BTS support:

FQGA:472467A

Range 7

Step -

Units characters



Default value -


Related functions -




Related options – RAN1299 BTS Auto Configuration


Table 393 unitTypeActual (Installed hardware unit type) (Cont.)

DN70577885 447



49.4 unitTypeExpected (Expected hardware unit type)


References -

Table 393 unitTypeActual (Installed hardware unit type) (Cont.)

Parameter name Expected hardware unit type

Abbreviated name unitTypeExpected

3GPP name -

Managed Object UNIT

Multiplicity 1

Description This parameter specifies the type of the hardware unit that is expected to be installed in the FTM slot.

Values are:


FIIB: 472271A

FILB: 472294A

FTEB: 470156A

FTFA: 470134A

FTFB: 472036A

FTHA: 471522A

FTIA: 471025A

FTIB: 471720A

FTJA: 471248A

FTLB: 471984A

FTOA: 470133A

FTPB: 470137A


FSM: Outdoor System Module

FSI: Indoor System Module

FTIF: 472311A

FIIF: 472355A

Flexi BTS support:

FQGA:472467A

Table 394 unitTypeExpected (Expected hardware unit type)

448 DN70577885



UNIT Parameters

Range 470137A (0), 470156A (1), 470134A (2), 471522A (3), 471025A (4), 471720A (5), 471248A (6), 470133A (7), 471984A (8), 472036A (9), 472271A (10), 472294A (11) for WN7.0 1.0;

470137A (0), 470156A (1), 470134A (2), 471522A (3), 471025A (4), 471720A (5), 471248A (6), 470133A (7), 471984A (8), 472036A (9), 472271A (10), 472294A (11), FSM (12), FSI (14), 472311A (16), 472355A (17), 472467A (18) for WN7.0 2.0

Step -

Units -


gui ==> internal

470137A ==> 0

470156A ==> 1

470134A ==> 2

471522A ==> 3

471025A ==> 4

471720A ==> 5

471248A ==> 6

470133A ==> 7

471984A ==> 8

472036A ==> 9

472271A ==> 10

472294A ==> 11

FSM ==> 12

FSI ==> 14

472311A ==> 16

472355A ==> 17

472467A ==> 18

Default value -


Related functions -




Related options – RAN1299 BTS Auto Configuration


Table 394 unitTypeExpected (Expected hardware unit type) (Cont.)

DN70577885 449




References -

Table 394 unitTypeExpected (Expected hardware unit type) (Cont.)

450 DN70577885



VCCT Parameters

50 VCCT Parameters





3GPP name -

Managed Object VCCT

Multiplicity 1


Range 32... 4095

Step 1

Units -



Default value -


Related functions -




Related options -



References -




3GPP name -

Managed Object VCCT

Multiplicity 1



DN70577885 451

Flexi Transport Module Parameters VCCT Parameters



Range 0... 255

Step 1

Units -



Default value -


Related functions -




Related options -



References -




3GPP name -

Managed Object VCCT

Multiplicity 1








Range 1... 76

Step 1


452 DN70577885



VCCT Parameters

50.4 trafficDescriptorId (Traffic Descriptor Pointer)

Units -



Default value -


Related functions -




Related options -



References -


Parameter name Traffic Descriptor Pointer

Abbreviated name trafficDescriptorId

3GPP name -

Managed Object VCCT

Multiplicity 1

Description This parameter points to the instance of the ATM traffic descriptor (TRDE) that contains the peak cell rate (PCR) settings for this virtual channel.

The value of the parameter is a number above 100. This references the identifier of the TRDE managed object instance, e.g. TRDE-104.

The traffic descriptor managed object instance must have been created before it can be referenced by this parameter.

Range 100... 9999999999

Step 1

Units -



Default value -

Table 398 trafficDescriptorId (Traffic Descriptor Pointer)

DN70577885 453

Flexi Transport Module Parameters VCCT Parameters




Related functions -




Related options -



References -

Table 398 trafficDescriptorId (Traffic Descriptor Pointer) (Cont.)



3GPP name -

Managed Object VCCT

Multiplicity 1


Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -



454 DN70577885



VCCT Parameters

50.6 vcCTPId (Virtual Channel Identifier (VCI))


References -


Parameter name Virtual Channel Identifier (VCI)

Abbreviated name vcCTPId

3GPP name -

Managed Object VCCT

Multiplicity 1

Description Naming attribute (relative to Virtual Path).

The value is the same as the attribute VCI

Range 32... 4095

Step 1

Units -



Default value -


Related functions -


Related parameters VCI of VCCT

Parameter relationships The value must be the same as the attribute VCI

Related options -



References -

Table 400 vcCTPId (Virtual Channel Identifier (VCI))

DN70577885 455

Flexi Transport Module Parameters VCTT Parameters


51 VCTT Parameters





3GPP name -

Managed Object VCTT

Multiplicity 1


Range 32... 4095

Step 1

Units -



Default value -


Related functions -




Related options -



References -




3GPP name -

Managed Object VCTT

Multiplicity 1



456 DN70577885



VCTT Parameters

51.3 aalProfilePtr (ATM Adaptation Layer (AAL) Profile Pointer)

Range 0... 255

Step 1

Units -



Default value -


Related functions -




Related options -



References -


Parameter name ATM Adaptation Layer (AAL) Profile Pointer

Abbreviated name aalProfilePtr

3GPP name -

Managed Object VCTT

Multiplicity 1

Description Specifies for which AAL type the virtual channel (VCCT) is terminated.

Supported types are AAL2-1 (AAL2 user traffic) and AAL5-1 (IP over ATM connections, AAL2 signal-ling).

Range AAL2-1 (1), AAL5-1 (2)

Step -

Units -


gui ==> internal

AAL2-1 ==> 1

AAL5-1 ==> 2

Table 403 aalProfilePtr (ATM Adaptation Layer (AAL) Profile Pointer)

DN70577885 457




Default value -


Related functions -




Related options -



References -

Table 403 aalProfilePtr (ATM Adaptation Layer (AAL) Profile Pointer) (Cont.)



3GPP name -

Managed Object VCTT

Multiplicity 1








Range 1... 76

Step 1

Units -



Default value -



458 DN70577885



VCTT Parameters


Related functions -




Related options -



References -




3GPP name -

Managed Object VCTT

Multiplicity 1


Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -



References -


DN70577885 459



51.6 vcTTPId (Virtual Channel Trail Termination Point Identi-fier)

Parameter name Virtual Channel Trail Termination Point Identifier

Abbreviated name vcTTPId

3GPP name -

Managed Object VCTT

Multiplicity 1

Description Naming attribute


- unitNumber(unit#)

- interfaceNumber (if#, imag# or pw#)

- virtual path identifier (vpi#)

- virtual channel identifier (vci#)

Possible formats (examples in parentheses):

- unit#-if#-vpi#vci# (2-8-000C0)

- slot#-imag#-vpi#vci# (2-34-00210)

Value ranges:

- unit#: 1

- if#: 1..16 (1 or 2 digits)

- imag#: 33..75 (2 digits)

- pw#: 76

- vpi#: 00..FF (hexadecimal number, 2 digits)

- vci#: 000..FFF (hexadecimal number, 3 digits)

Range 9...10

Step -

Units characters



Default value -


Related functions -


Related parameters VCI of VCTT

VPI of VCTT

interfaceNumber of VCTT

unitNumber of VCTT

Table 406 vcTTPId (Virtual Channel Trail Termination Point Identifier)

460 DN70577885



VCTT Parameters

Parameter relationships The VCTT id is composed of the values of these other attributes.

Related options -



References -

Table 406 vcTTPId (Virtual Channel Trail Termination Point Identifier) (Cont.)

DN70577885 461

Flexi Transport Module Parameters VPCT Parameters


52 VPCT Parameters





3GPP name -

Managed Object VPCT

Multiplicity 1


Range 0... 255

Step 1

Units -



Default value -


Related functions -




Related options -



References -




3GPP name -

Managed Object VPCT

Multiplicity 1


462 DN70577885



VPCT Parameters

52.3 trafficDescriptorId (Traffic Descriptor Pointer)








Range 1... 76

Step 1

Units -



Default value -


Related functions -




Related options -



References -


Parameter name Traffic Descriptor Pointer

Abbreviated name trafficDescriptorId

3GPP name -

Managed Object VPCT

Multiplicity 1

Table 409 trafficDescriptorId (Traffic Descriptor Pointer)

DN70577885 463




Description This parameter points to the instance of the ATM traffic descriptor (TRDE) that contains the peak cell rate (PCR) settings for this virtual path.

The value of the parameter is a number above 100. This references the identifier of the TRDE managed object instance, e.g. TRDE-104.

The traffic descriptor managed object instance must have been created before it can be referenced by this parameter.

Range 100... 9999999999

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 409 trafficDescriptorId (Traffic Descriptor Pointer) (Cont.)



3GPP name -

Managed Object VPCT

Multiplicity 1


Range 1... 1


464 DN70577885



VPCT Parameters

52.5 vpCTPId (Virtual Path Identifier (VPI))

Step 1

Units -



Default value -


Related functions -




Related options -



References -


Parameter name Virtual Path Identifier (VPI)

Abbreviated name vpCTPId

3GPP name -

Managed Object VPCT

Multiplicity 1

Description Specifies a virtual path on an ATM interface (TCTT) and serves as naming attribute for this object.

The value range is defined in the access profile of the ATM interface with the attribute maxNumVPIB-itsSupported.

Range 0... 255

Step 1

Units -



Default value -


Related functions -

Table 411 vpCTPId (Virtual Path Identifier (VPI))

DN70577885 465






Related options -



References -

Table 411 vpCTPId (Virtual Path Identifier (VPI)) (Cont.)

466 DN70577885



VPTT Parameters

53 VPTT Parameters





3GPP name -

Managed Object VPTT

Multiplicity 1


Range 0... 255

Step 1

Units -



Default value -


Related functions -




Related options -



References -




3GPP name -

Managed Object VPTT

Multiplicity 1


DN70577885 467

Flexi Transport Module Parameters VPTT Parameters










Range 1... 76

Step 1

Units -



Default value -


Related functions -




Related options -



References -




3GPP name -

Managed Object VPTT

Multiplicity 1


Range 1... 1


468 DN70577885



VPTT Parameters

53.4 vpTTPId (Virtual Path Trail Termination Point Identifier)

Step 1

Units -



Default value -


Related functions -




Related options -



References -


Parameter name Virtual Path Trail Termination Point Identifier

Abbreviated name vpTTPId

3GPP name -

Managed Object VPTT

Multiplicity 1

Table 415 vpTTPId (Virtual Path Trail Termination Point Identifier)

DN70577885 469

Flexi Transport Module Parameters VPTT Parameters


Description Specifies the termination of the virtual path.


- unitNumber(unit#)

- interfaceNumber (if#, imag#)

- virtual path identifier (vpi#)

- pw tunnel id (pwt#)

Possible formats:

- unit#-if#-vpi#

- unit#-imag#-vpi#

- unit#-pwt#-vpi#

Value ranges:

unit#: 1

if#: 1..16

imag#: 33..75

vpi#: 0..255

pwt#: 76

Range 5...8

Step -

Units characters



Default value -


Related functions -


Related parameters VPI of VPTT - The value of parameter VPI is contained in the value of parame-ter vpTTPId.

interfaceNumber of VPTT - The value of parameter interfaceNumber is contained in the value of parameter vpTTPId.

unitNumber of VPTT - The value of parameter unitNumber is contained in the value of parameter vpTTPId.

Parameter relationships The VPTT id is composed of the values of these other attributes

Related options -


Table 415 vpTTPId (Virtual Path Trail Termination Point Identifier) (Cont.)

470 DN70577885



VPTT Parameters


References -

Table 415 vpTTPId (Virtual Path Trail Termination Point Identifier) (Cont.)

ref flexi trns param

Documents

product safetythis product

operating documentation

documentation set

safety information applicable

safety information section

environmental information

product names

safety risks