INSTRUCTION MANUAL

MODEL: HD6EMD / HD9EMD / HD12EMD / HD15EMD

READ THESE INSTRUCTIONS CAREFULLY

1. SAFETY INSTRUCTIONS

- Means for disconnection must be incorporated in the fixing wiring in according with the wiring rules.

- A means of disconnection from the power supply having a contact opening distance of all poles must be included in the fixed wiring in accordance with the installation requirements.

- WARNINGS ：In order to avoid overheating, do not cover the heater.

- The device must not be exposed to water drops or splash.

- The appliance should not be placed immediately below a socket.

- The unit must not be exposed to dripping or splashing water.

- The appliance must not be used in damp rooms (bathroom in the volume 0 and 1).

- The device must not be used outdoors.

- The device should not be removed to avoid the risk of electric shock.

- The device is only intended for domestic use.2

- Do not apply pressure to the front of the unit or on the sides or on top.

- If the power cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

- CAUTION: To avoid hazard due to inadvertent resetting of the thermal cutout, this appliance must not be powered via an external switch, such as a timer, or connected to a circuit that is regularly in and off by the electricity supplier.

- NOTE - Some parts of this product may become hot and cause burns. Particular attention should be given where children and vulnerable people are present.

- The heater must be installed so that switches and other control devices can not be touched by a person in the bath or shower.

- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

- Children of less than 3 years should be kept away unless continuously supervised.

- Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been

3

placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

- Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.

- CAUTION — Some parts of this product can become very hot and cause burns.

- Particular attention has to be given where children and vulnerable people are present.

- Keep the device at a minimum safety distance of one meter from any inflammable material (curtains, furniture…)

- Keep the device away from a gas cooker, a gas oven, flames, or any inflammable liquids.

- Clean the device with a slightly humid towel after you switched off the circuit breaker which supplies the device. - Do not use any chemical solvent nor abrasive products to clean the surface of the device at the risk of scratching, damaging, or even distorting it.

- The heater must not be located immediately below a socket outlet.

4

The European directive 2012/19/EU on Waste Electrical and ElectronicEquipment (WEEE), requires that old household electrical appliances must not be disposed in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain and reduce the impact on human health and the environment.The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected.Consumers should contact their local authority or retailer for information concerning thecorrect disposal of their old appliance

INSTALLATION

Your appliance must be used as fixed appliance (thanks to respect all the safety warnings given above)

Always direct the airflow in order to optimize the heating of the room.

Avoid the corners, small volumes, wood floors, ceiling, etc…

INDOOR USE ONLY

If you are not sure, it’s recommended to ask a qualified electrician for help.

To hang your heater on the wall:

Choose a correct location for the heater. (Figure 1)

Drill 6 holes on the wall and put the plastic pegs in the holes. (Figure 2)

Fix the 2 higher hooks onto the wall with screws. (Figure 2)

Fix the two lower hooks onto the bottom of the heater. (Figure 3)

Hang the heater onto the two higher hooks. (Figure 4)

5

Screw tightly the remaining screws of the lower hooks. Always be sure that the heater is correctly fixed and stable after performing the installation! (Figure 5)

Model HD6EMD HD9EMD HD12EMD HD15EMDL1 138mm 225mm 302MM 399mm

6

LCD DISPLAY:

1. LCD Display Screen:

2. Functional Icons on LCD Screen: Mode Standby Mode Anti-freeze Mode Comfort Mode Economic

Mode Programme

Keyboard Lock:

Temperature (centigrade)

Under Customized Program Setting:

Working under Comfort Mode Working under Economic Mode

Stand-By

CONTROL PANEL： 1. Control Panel

7

2. Icons on Control Panel: + /- button：press to modulate time, day of week, temperature, or to select among comfort/economic/stand-by mode under customized programme setting.

button：press to set temperature

button：press to set clock, or toggle among hour/minute/week.M button：press to choose working mode:

Comfort /Economic/Antifreeze PROG button：press to choose program: P1/P2/P3/customized

button：stand by button： press to confirm/finish settings or to lock/unlock the Control panel

HOW TO USE

BEFORE FIRST USE

Remove all packaging and check the appliance for any damages during transportation. If there appears to be any damages, please take back the damaged heater to the place of purchase for a replacement.

Ensure a power socket is available to power the heater and that the heater is not directly located under the power socket

Ensure the heater is placed on a level surface with enough clearance from its surroundings.

Do not place the heater on LONG PILE CARPET OR FLOKATI RUGS. Use a heat board if necessary.

8

I. ON/OFF

1) Plug the heater into wall socket with the same voltage, frequency and rating as indicated on the product identification plate.

2) When the heater is switched on, the clock will pop out on the display for setting. Time setting finished, the appliance will automatically enter standby mode as defaulted. press Stand-by mode button to make the heater start working

II. Working mode setting

Notes:

- For first use, pressong the button to turn the device into Comfort mode. - In case of power failure, after reconnecting the power supply, the unit will be in standby mode. Pressing the standby button , JUST RE-SET THE TIME TO BE CURRENT TIME and the unit will be worked as the mode and temperature before power failure.

Press M button continuously to select among the 3 modes: Economic

mode Antifreeze mode , and Comfort mode ，

Comfort mode (Setting the desired temperature from 5-35 )℃

Eco mode (ECO Maintains temperature which is equal to the comfort temperature lowered by 3.5 ° C. This mode reduces the temperature without disturbing the desired comfort mode temperature)

Antifreeze mode (the device maintains the room temperature at approximately 7 ° C)

9

III. Temperature setting.

1. Press button to display the set temperature.2. Press +/- button to select the desired temperature between 5℃ to 35℃.

3. Press button to finish the setting, or after 30 seconds, it will automatically finish. The temperature sensor can automatically test the temperature. When the room temperature is higher than the selected temperature, the heater will stop heating.

IV. Clock & Day of Week Setting

Please note:- The purpose of Clock&Day of Week Setting is to set the current time

and day of week. - Clock& Day setting is only related to Mode Programme

(P1/P2/P3/Individual 7 day programme).- This setting will also be regarded as the last time the machine started

operation. - The ‘day of week’ setting and ‘time period’ setting in all Programs

(refer to V, P1/P2/P3/customized) will be based on this setting.

1. Press button. Continute to press button to select among hour/minute/day of week setting.

2. Press +/-buttons to set the hour/minute/ day of week

Selection IconDisplayedMonday 1Tuesday 2

Wednesday 3Thursday 4

Friday 5Saturday 6Sunday 7

Hour 00-23Minute 01-59

10

3. Press button to confirm settings ONLY when you finish all the settings of hour/minute/day of week. Or after 30 seconds, it will automatically confirm the setting.

V. P1/P2/P3/customized

NOTE: If the power supply is cut, after recovery, the unit is in standby mode. Press the button standby to enter the mode and temperature before the power failure. Please set the clock again.

1. P1/P2/P3 are preinstalled programs. After confirming the program, the icon of the program and set temperature will be displayed alternately on the screen.

2. Customized Program SettingPress “PROG “button continuously to select among the setting of “day of week”,”time period” and “working mode” .

Select the desired day of week (1-7) by pressing +/- button;

Select different time period (1-24h) by pressing “+”button;

Select different working mode (comfort , economic , and stand by )

by pressing the “-“ button.

Press button to confirm settings ONLY when you finish all the settings of working mode for whole week (1-7), or after 30 seconds, it will automatically confirm the setting.

For example: To select 1（Monday）,economy mode for 24 hours:

11

1) Press PROG button to select customized program setting mode. Press button to start the settings and enter day of week (1-7) setting.

2) Press “+/- “button to select 1 (Monday)

3) Press “PROG” button again to enter “time period (1-24h)” setting, then

press “+”button to select 1:00am, and press“-“button to select economy mode . Repeat this setting for the next hour 2:00am, and then 3:00am…. until 24:00pm.

4) .After set up for 1 （Monday）, press “PROG” button and repeat above steps 2~3 to set for following days(2-7).

VI: keyboard lock Press for three seconds to activate the keyboard lock function , in order to unlock, press again for three seconds.

Notes:

A) If the PROG is under setting, is pressed, it means finished the setting rather than key-board locking

B) After finishing programme-setting, the heater works on the MODE (no matter COMFORT, ECO, ANTIFREEZE or PROG), pressing, and panel is blocked.

12

Keyboard lock

VII: Technical data

VIII: Background light

Background light will be automatically switched off:

1. 60 seconds after keyboard lock/reactived after unlock;2. 60 seconds after the last touch of panel buttons/reactived when any

button is touched

IX: Validity of Settings

All settings above for tempature, clock, date of week and programs will be valid as long as the power is on.

If the power is cut-off, clock and date of week must be redone for next operation. While temperature, mode and programs will be valid and no need to reset.

Lock the keyboard after setting to avoid changing of settings by careless touching of the panel.

CLEANING & MAINTENANCE- Always disconnect appliance from the mains supply when you clean it.- NEVER IMMERSE THE HEATER TO CLEAN IT - To avoid any electrical hazard, clean your appliance with a soft and

clean rag to remove the dust. You can also use a vacuum cleaner to clean the air openings.

- Clean your appliance regularly

ModelVoltage

& FrequenceRated power

(Watt）Fin QTY Class

HD6EMD 230V ~ 50Hz 600W 4 CLASS I

HD9EMD 230V ~ 50Hz 900W 5 CLASS I

HD12EMD 230V ~ 50Hz 1200W 6 CLASS I

HD15EMD 230V ~ 50Hz 1500W 7 CLASS I

13