[r1] installation topfix / recessfix [r1] · 2016. 11. 25. · tassel on the cap. for installation...
TRANSCRIPT
25AU20
10-0
6-20
14
[R1]
Instal
lation
and U
serrsquos
man
ual P
B - G
B
Subject to technical changes 128Installation and User manual
Installation TopFix RecessFix [R1]
Young children can be strangled by loops in pull cords chains tapes and inner cords that operate the product They can also wrap cords around their necks To avoid strangulation and entanglement keep cords out of
reach of young children Move beds cots and furniture away from window covering cords Do not tie cords together Make sure cords do not twist and create a loop Install and use the included safety devices according to the installation instructions on these devices to reduce possibility of such an accident According to EN 13120
Do not damage the product when using a sharp knife to open the packaging Fitting screws Use a size-2 screwdriver (PO-ZIDRIVE) or use an electric screwdriver at itrsquos lowest torque Rail removal Use a flat screwdriver of max 6 mm wide Only
use the original screws enclosed to prevent malfunctioning from using too thick screw heads
WARNING
Model
A
B
C
Removal
X=5 cm
x max 80 cm x
37
25
52
28
15
2-A1 2-A2
1 Clip installation
Rail installation sequence on Clips
2 Installation 1
2
36
4-A 4-C To lower the shade To raise the shade
Click
4
5
4-B To lower the shade
Click
Do not raise bottomrail higher than the midrail to avoid a hazar-dous loop
15m
3 Adjust control height
For installation height from 15m the tassel must be at least 15m from the floor To adjust the tassel height push the tassel cap up the cord and tie a knot on the required height Then cut the cord under the knot and click the enclosed transparent part of the tassel on the cap
For installation height onbelow 15m the operation cord length is max 1cm To adjust the operation cord length push the tassel cap up to the headrail Tie a knot as high as possible then cut the cord under the knot and click the enclosed transparent part of the tassel on the cap
2
3
30 - 90 cm
90 - 180 cm
4
2
3
4180 - 270 cm
5 5270 - 300 cm
Product width Number of parts
25AU20
10-0
6-20
14
[F1]Ins
tallat
ion an
d Use
rrsquos m
anua
l PB
- GB
Subject to technical changes 129Installation and User manual
FaceFix installation to a window frame wall [F1]
Young children can be strangled by loops in pull cords chains tapes and inner cords that operate the product They can also wrap cords around their necks To avoid strangulation and entanglement keep cords out of
reach of young children Move beds cots and furniture away from window covering cords Do not tie cords together Make sure cords do not twist and create a loop Install and use the included safety devices according to the installation instructions on these devices to reduce possibility of such an accident According to EN 13120
Do not damage the product when using a sharp knife to open the packaging Fitting screws Use a size-2 screwdriver (PO-ZIDRIVE) or use an electric screwdriver at itrsquos lowest torque Rail removal Use a flat screwdriver of max 6 mm wide Only
use the original screws enclosed to prevent malfunctioning from using too thick screw heads
WARNING
Model
A
B
C
Removal
2-A1 2-A2
1 Clip installation
Rail installation sequence on Clips
2 Installation
1
2
36
4-A 4-C To lower the shade To raise the shade
Click
4
5
4-B To lower the shade
Click
X=5 cm
x max 80 cm x
28
37
15
52
28
Do not raise bottomrail higher than the midrail to avoid a hazar-dous loop
2
3
30 - 90 cm
90 - 180 cm
4
2
3
4180 - 270 cm
5 5270 - 300 cm
Product width Number of parts
15m
3 Adjust control height
For installation height from 15m the tassel must be at least 15m from the floor To adjust the tassel height push the tassel cap up the cord and tie a knot on the required height Then cut the cord under the knot and click the enclosed transparent part of the tassel on the cap
For installation height onbelow 15m the operation cord length is max 1cm To adjust the operation cord length push the tassel cap up to the headrail Tie a knot as high as possible then cut the cord under the knot and click the enclosed transparent part of the tassel on the cap
25AU20
10-0
6-20
14
[F1]Ins
tallat
ion an
d Use
rrsquos m
anua
l PB
- GB
Subject to technical changes 129Installation and User manual
FaceFix installation to a window frame wall [F1]
Young children can be strangled by loops in pull cords chains tapes and inner cords that operate the product They can also wrap cords around their necks To avoid strangulation and entanglement keep cords out of
reach of young children Move beds cots and furniture away from window covering cords Do not tie cords together Make sure cords do not twist and create a loop Install and use the included safety devices according to the installation instructions on these devices to reduce possibility of such an accident According to EN 13120
Do not damage the product when using a sharp knife to open the packaging Fitting screws Use a size-2 screwdriver (PO-ZIDRIVE) or use an electric screwdriver at itrsquos lowest torque Rail removal Use a flat screwdriver of max 6 mm wide Only
use the original screws enclosed to prevent malfunctioning from using too thick screw heads
WARNING
Model
A
B
C
Removal
2-A1 2-A2
1 Clip installation
Rail installation sequence on Clips
2 Installation
1
2
36
4-A 4-C To lower the shade To raise the shade
Click
4
5
4-B To lower the shade
Click
X=5 cm
x max 80 cm x
28
37
15
52
28
Do not raise bottomrail higher than the midrail to avoid a hazar-dous loop
2
3
30 - 90 cm
90 - 180 cm
4
2
3
4180 - 270 cm
5 5270 - 300 cm
Product width Number of parts
15m
3 Adjust control height
For installation height from 15m the tassel must be at least 15m from the floor To adjust the tassel height push the tassel cap up the cord and tie a knot on the required height Then cut the cord under the knot and click the enclosed transparent part of the tassel on the cap
For installation height onbelow 15m the operation cord length is max 1cm To adjust the operation cord length push the tassel cap up to the headrail Tie a knot as high as possible then cut the cord under the knot and click the enclosed transparent part of the tassel on the cap