r09-cmos analog and mixed signal design

1
JNTUWORLD Code No: D0608 JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD M.TECH II - SEMESTER EXAMINATIONS, APRIL/MAY-2012 CMOS ANALOG AND MIXED SIGNAL DESIGN (DIGITAL SYSTEMS AND COMPUTER ELECTRONICS) Time: 3hours Max. Marks: 60 Answer any five questions All questions carry equal marks - - - 1.a) Draw a standard cascode current sink circuit and explain its operation and output characteristics. b) Calculate the temperature coefficient of the Threshold referenced circuit, where ( ) 1 20 W L = , V DD = 5V and R = 100k. Assume the other required values. Resistor R is Polysilicon and has a temperature coefficient of 1500 ppm/ 0 C, α = 2.3 x 10 -3 V/ 0 C. 2.a) Show that the sensitivity of the reference circuit shown in the figure is unity. b) Draw a layout of current mirror circuit. R09 3.a) Draw a neat current sink inverter circuit and explain the operation. b) If W 1 = 2μm, L 1 = 1μm, W 2 = 1μm, L 2 = 1μm, V DD = 5V, V GG1 = 3V for a CMOS current sink inverter circuit having two transistors M 1 and M 2 . Calculate output- swing limits. 4. Draw the four feed back topologies and derive the expression for feedback factor and show the effect of feedback on voltage gain in all the 4 topologies. 5. Design an op-amp with ideal op-amp characteristics. Explain the steps, conditions and requirements to design an op-amp. 6.a) Explain the principle of Miller Compensation of two stage op-amp b) How can we improve the performance of open-loop comparator? 7. Explain the function of switched capacitor voltage amplifier using the parallel resistor emulation. 8. Write a brief note on: a) Mixed signal layout b) ADC architecture (any one has to be discussed) * * * * * * www.jntuworld.com www.jntuworld.com www.jwjobs.net

Upload: balashyamu

Post on 02-Jan-2016

439 views

Category:

Documents


0 download

DESCRIPTION

JNTUH Mtech 2nd sem Cmos Analog and Mixed Signal Design question paper Cmos Analog and Mixed Signal Design for Cmos Analog and Mixed Signal Design for VLSI and VLSI System design JNTUH Mtech 2nd sem Cmos Analog and Mixed Signal Design question paper Cmos Analog and Mixed Signal Design for Cmos Analog and Mixed Signal Design for VLSI and VLSI System design

TRANSCRIPT

Page 1: r09-Cmos Analog and Mixed Signal Design

JNTUWORLD

Code No: D0608 JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD

M.TECH II - SEMESTER EXAMINATIONS, APRIL/MAY-2012 CMOS ANALOG AND MIXED SIGNAL DESIGN

(DIGITAL SYSTEMS AND COMPUTER ELECTRONICS) Time: 3hours Max. Marks: 60

Answer any five questions All questions carry equal marks

- - - 1.a) Draw a standard cascode current sink circuit and explain its operation and output

characteristics. b) Calculate the temperature coefficient of the Threshold referenced circuit,

where ( )1

20WL = , VDD = 5V and R = 100kΩ. Assume the other required values.

Resistor R is Polysilicon and has a temperature coefficient of 1500 ppm/0C, α = 2.3 x 10-3V/0C.

2.a) Show that the sensitivity of the reference circuit shown in the figure is unity.

b) Draw a layout of current mirror circuit.

R09

3.a) Draw a neat current sink inverter circuit and explain the operation. b) If W1 = 2μm, L1 = 1μm, W2 = 1μm, L2 = 1μm, VDD = 5V, VGG1 = 3V for a CMOS

current sink inverter circuit having two transistors M1 and M2. Calculate output-swing limits.

4. Draw the four feed back topologies and derive the expression for feedback factor

and show the effect of feedback on voltage gain in all the 4 topologies. 5. Design an op-amp with ideal op-amp characteristics. Explain the steps, conditions

and requirements to design an op-amp. 6.a) Explain the principle of Miller Compensation of two stage op-amp b) How can we improve the performance of open-loop comparator? 7. Explain the function of switched capacitor voltage amplifier using the parallel

resistor emulation. 8. Write a brief note on: a) Mixed signal layout b) ADC architecture (any one has to be discussed)

* * * * * *

www.jntuworld.com

www.jntuworld.com

www.jwjobs.net