Quick Start GuideSnap

SD-H2304

Getting to Know Your Snap1

①

③

④

②

1080p HD Camera

Light Sensor

PIR Motion Sensor &

Power / Reset Button

Status Light

①

②③④

Snap is a true wireless IP camera with a built-in rechargeable battery. You can install your Snap anywhere in your home without any complicated installation or wiring. Once you place or mount your camera, you will be notified when your Snap needs to be recharged from the meShare app.

⑤

⑥

⑤

⑥

Charging Zone

Status Light Indicator

⑦ Power Port

1

⑦

Snap (Camera)

Charging Pad

Note: *Press and hold the power / reset button for 3-5 seconds, Snap will be powered on / off. *Press and hold the power / reset button for longer than 10 seconds to reset your Snap. Your Snap will be disconnected from any WiFi network.*If you cannot power on your Snap, it may need to be charged.

What’s in the Box :

Power Adapter

Wireless Charging PadSnap(Wireless Camera)

Mounting Bracket Installation Hardware

2

Hub

Quick Start Guide

Quick Start GuideSnap

SD -H2304

3

Mobile Setup

We are constantly working to improve our product and app. Please visit www.zmodo.com/support for updated instructions, manuals, and more.

You will need a strong 2.4GHz WPA/WPA2 WiFi networkconnection at the location of your hub.

Make sure you know the SSID (WiFi network name) and password of the 2.4GHz WPA-PSK/WPA2-PSK WiFi network that you want your hub to connect to. Your network cannot be hidden.

TMDownload and install the "meShare" app from Google Play TM ® TMor the App Store (Compatibility: iOS 9.0+ or Android

4.0+). Launch the app and sign up for a free meShare account. All of your devices will be bound to this account.

Before you begin:

Plug the hub into a power outlet near your WiFi router for the initial setup.

Make sure your network has at least 2mbps upload speed for each camera when live viewing or 4mbps upload speed for each camera when using the cloud service.

www.zmodo.com/support

2

Please refer to the following instructions to configure your Snap. For detailed instructions and troubleshooting, please visit:

meShare

4

Make sure that you have powered on the hub, and then press and hold the power button for at least 3-5 seconds to power on your Snap.

Tap “Start installation” to proceed.

2

3 Scan this QR code shown below when prompted by the app.

Log in and press the Add Device option in the upper right corner of the Home Page.

+1

4 Follow the in-app instructions to complete the setup.

5

Keep away from sources of heat and fire, i.e. a space heater or candle.

Safety Requirements:

Make sure that the hub is within range of your WiFi router and within reasonable distance to your Snap.

Selecting a location for your hub:

Hub Placement Suggestions

Avoid a location with electronic appliances that generate strong magnetic or electric fields, such as microwave ovens or refrigerators.

Place in a cool and well-ventilated indoor area.

Do not expose to direct sunlight.

If water or liquid damage occurs, unplug the hub immediately.

After completing setup, unplug your hub and follow the instructions below to find an optimal location for it.

6

Charging Pad Status Light Definitions

Blinking blue

The camera is placed correctly and charging.

The charging pad is powered on, but no camera has been placed on the pad, or the camera has been placed improperly.

Solid red

Note: You will not be able to view or change the settings of your Snap while it is charging.

Hub Status Light Definition

The hub is successfully connected to a WiFi network.

Blinking White

The hub is not yet connected to the WiFi network.

Solid White

Your Snap is connecting to the hub.

Blinking Blue

Snap Status Light

Your Snap is successfully connected to the hub.

Solid Blue

Snap is powering on.

Solid Green

Snap is ready for setup.

Blinking Green

3 Status Light Definitions

4 Charging your Snap

You will receive an alert on your smartphone through the meShare app whenever your Snap needs to be recharged. Please follow the steps below to charge your Snap:

Place your Snap on the charging pad (as shown). Thestatus light on your charging pad will tell you if it ischarging.

3

1

2

7

When it is fully charged, you will receive an alert on yoursmartphone. Remove the camera and place it back intothe original position.

4

Plug in the wireless charging pad to a power outlet usingthe included power adapter.

Remove the Snap from the mounting bracket if mounted.

5 Mounting your Snap

Once your Snap has been connected to a WiFi network, youcan mount or place it on any flat surface. Please make surethat your Snap is within range of the hub, and that it is fullycharged before installation.

1 Line the camera bracket against the wall and mark the appropriate holes. Drill two holes slightly smaller than the wall anchor and use a hammer to gently insert the anchors into the wall. Fasten the two screws through the holes on the bracket into the anchors as shown.

8

2 Fasten the Snap to the mounting bracket using theincluded screw and washer, and adjust the camera foran optimal viewing angle.

9

Main Features46

Snap has a built-in rechargeable battery, which means that you're totally wire-free. Access a live video from Snap any time from the meShare app.

100% Wireless Camera

10

Snap allows you to monitor your home day and night. You can see your loved ones directly from your smartphone.

You can access your Snap's full features by using the meShare TM ®app on your Android or iOS smartphone.

This section will cover the main features of your Snap camera.

You can also view your Snap using any web browser by logging into with your user account user.meshare.cominformation.

11

Snap will wake up and record a video clip whenever motion is detected, making sure that you are kept in the loop for the important moments.

Smart motion detection

A 180° ultra wide-angle view allows you to capture more of your space, all at once. Automatic fisheye correction means that you get a bigger, more detailed, and more accurate picture of your space.

180° wide-angle view

12

You can check your camera’s status light to determine if your camera has been connected to the WiFi or not.

Troubleshooting

Please make sure that you entered the network name and password correctly. Note: Both are case-sensitive.

Make sure that you are connecting to a 2.4GHz WPA-PSK/WPA2-PSK WiFi network, and your network is not hidden.

Please make sure that your phone's display brightness is not too high when scanning the QR code during Mobile Setup.

You may need to improve your WiFi strength. Try moving your router closer to your hub, or purchasing a WiFi range extender.

7

If it is blinking green, it means that it has not been connectedto the WiFi network and you may need to retry the setup method.

If it is solid blue, it means that it is connected to the WiFi network.

If you were unable to connect your device successfully:

You need reset your hub if you want to connect your device again or change another WiFi network. To resetthe hub, please use a pin to press and hold the reset button for 5 seconds.

Having difficulty?

Follow us on Twitter @Zmodo

Like us on Facebook.com/Zmodo

www.zmodo.com/support

We would love to help. You can use the Live Chat functionin the meShare app if you have any technical problems.Just open the “Me” page in the lower right corner of the Home Page and select “meShare Support”.

For more instructions, troubleshooting, support, and otherresources, please visit

Contact Us8

13

Enjoy your Zmodo product

Your feedback means a lot to us! Please share your positiveexperience on your favorite social media site to help spreadthe word.

REV-A03