quality control – q6 edge hd quantumq6 edge hd quality control – q6 edge hd. warning! a quantum...

QUANTUM

Pride keeps a more detailed report on file at the factory.

Date Inspected

Inspector

Inclusion of all Parts

Joystick Serial Number

Controller Serial Number

Left Motor Serial Number

Right Motor Serial Number

Fit and Finish

Performance

*INFMANU4237* Product Serial #

Q6 Edge HD

Quality Control – Q6 Edge HD

WARNING! A Quantum Rehab Provider or a qualified technician must perform the initial setup ofthis power chair and must perform all of the procedures in this manual.

The symbols below are used throughout this owner’s manual and on the power chair to identify warnings andimportant information. It is very important for you to read them and understand them completely.

WARNING! Indicates a potentially hazardous condition/situation. Failure to follow designatedprocedures can cause either personal injury, component damage, or malfunction. On theproduct, this icon is represented as a black symbol on a yellow triangle with a black border.

MANDATORY! These actions should be performed as specified. Failure to perform mandatoryactions can cause personal injury and/or equipment damage. On the product, this icon isrepresented as a white symbol on a blue dot with a white border.

PROHIBITED! These actions are prohibited. These actions should not be performed at any timeor in any circumstances. Performing a prohibited action can cause personal injury and/orequipment damage. On the product, this icon is represented as a black symbol with a red circleand red slash.

INTENDED USEThe intended use of the Pride Mobility Products device is to provide mobility to persons limited to a seatedposition that have the capability of operating a powered wheelchair.

Quick Reference Information

S A F E T Y G U I D E L I N E S

Copyright © 2012Pride Mobility Products Corp.INFMANU4237/Rev A/April 2012

Quantum Rehab Provider:

Address:

Phone Number:

Purchase Date:

NOTE: This owner’s manual is compiled from the latest specifications and product information available atthe time of publication. We reserve the right to make changes as they become necessary. Any changes to ourproducts may cause slight variations between the illustrations and explanations in this manual and the productyou have purchased. The latest/current version of this manual is available on our website.

Q6 Edge HD www.pridemobility.com 3

I. INTRODUCTION .................................................................................................................................. 4

II. SAFETY ................................................................................................................................................... 5

III. YOUR POWER CHAIR .................................................................................................................... 17

IV. ASSEMBLY .......................................................................................................................................... 21

V. COMFORT ADJUSTMENTS ......................................................................................................... 25

VI. BATTERIES AND CHARGING ..................................................................................................... 31

VII. CARE AND MAINTENANCE ......................................................................................................... 35

C O N T E N T S

4 www.pridemobility.com Q6 Edge HD

I . I N T R O D U C T I O N

SAFETYWELCOME to Quantum Rehab, a division of Pride Mobility Products (Pride). The power chair you have pur-chased combines state-of-the-art components with safety, comfort, and styling in mind. We are confident thatthese design features will provide you with the conveniences you expect during your daily activities. Once youunderstand how to safely operate and care for your power chair, it should give you years of trouble free operationand service.

Read and follow all instructions, warnings, and notes in this manual before attempting to operate your power chairfor the first time. You must also read all instructions, warnings, and notes contained in any supplemental instruc-tional booklets for the controller, front riggings, and/or seating system that accompanied your power chair beforeinitial operation. Your safety depends upon you, as well as your provider, caretaker, or healthcare professional inusing good judgment.

If there is any information in this manual which you do not understand, or if you require additional assistance forsetup or operation, please contact your Quantum Rehab Provider. Failure to follow the instructions in thismanual and those located on your power chair can lead to personal injury and/or damage to the powerchair, including voiding the warranty.

PURCHASER’S AGREEMENTBy accepting delivery of this product, you promise that you will not change, alter, or modify this product orremove or render inoperable or unsafe any guards, shields, or other safety features of this product; fail, refuse, orneglect to install any retrofit kits from time to time provided by Pride to enhance or preserve the safe use of thisproduct.

SHIPPING AND DELIVERYBefore using your power chair, make sure your delivery is complete as some components may be individuallypackaged. If you do not receive a complete delivery, please contact your Quantum Rehab Provider immediately.Where damage has occurred during transport, either to the packaging or content, please contact the delivery com-pany responsible.

INFORMATION EXCHANGEWe want to hear your questions, comments, and suggestions about this manual. We would also like to hear about thesafety and reliability of your new power chair, and about the service you received from your Quantum Rehab Provider.

Please notify us of any change of address, so we can keep you apprised of important information about safety,new products, and new options that can increase your ability to use and enjoy your power chair. Please feel freeto contact us at the address below:

USA: Canada:Pride Mobility Products Corporation Pride Mobility Products CompanyAttn.: Customer Care Department 380 Vansickle Road Unit 350182 Susquehanna Avenue St. Catharines, Ontario L2R 6P7Exeter, PA 18643-2694 [email protected]

NOTE: If you ever lose or misplace your product registration card or your copy of this manual, contact us andwe will be glad to send you a new one immediately.


Avoid exposure to rain, snow, ice, salt, or standing water whenever possible.Maintain and store in a clean and dry condition.

Do not use a cell phone, walkie/talkie, laptop, or other radio transmitter whileoperating.

Keep your hands away from the tires when driving. Be aware that loose fittingclothing can become caught in drive tires.

Maximum seating weight.

Do not allow unsupervised children to play near the power chair while the batteriesare charging.

Read and follow the information in the owner’s manual.

I I . S A F E T Y

PRODUCT SAFETY SYMBOLSThe symbols below are used on the power chair to identify warnings, mandatory actions, and prohibited actions.It is very important for you to read and understand them completely.

Indicates flammable material. Do not expose to heat sources such as open flame orsparks. Do not transport batteries with flammable or combustible items.


Corrosive chemicals contained in battery.

Explosive conditions exist!

I I . S A F E T Y

Removal of grounding prong can create electrical hazard. If necessary, properlyinstall an approved 3-pronged adapter to an electrical outlet having 2-pronged plugaccess.

Do not connect an extension cord to the AC/DC converter or the battery charger.

Keep tools and other metal objects away from battery terminals. Contact with toolscan cause electric shock.

Use only AGM or Gel-Cell batteries to reduce the risk of leakage or explosiveconditions.

Do not mix AGM and Gel-Cell batteries. Always use batteries of the same type andchemistry.

Do not use batteries with different amp-hour (Ah) capacities. Do not mix old and newbatteries. Always replace both batteries at the same time.

EMI/RFI—This product has been tested and passed at an immunity level of 20 V/m.


Battery charger for indoor use only.

Battery posts, terminals, and related accessories contain lead and lead compounds.Wear goggles and gloves when handling batteries and wash hands after handling.

I I . S A F E T Y

Unlocked and in freewheel mode.

Locked and in drive mode.

Battery Set Configuration:+ = Positive (Red) Terminal Post- = Negative (Black) Terminal PostConnect Red wires to Red Positive (+) Terminal Posts.Connect Black wires to Black Negative (-) Terminal Posts.

Indicates electrical shock hazard.

Place unit on level ground and stand to one side when changing from drive modeto freewheel mode or freewheel mode to drive mode.

Do not place your power chair in freewheel mode while on an incline or decline.


Disposal and recycling—Contact your Quantum Rehab Provider for information onproper disposal and recycling of your Pride product and its packaging.

I I . S A F E T Y

Class II Equipment

Manufactured in

Power chair information label

Does not meet 7176-19 standards for occupied transport in a motorvehicle.

Indicates power chair securement points.

FRONT COVER

I I . S A F E T Y

GENERAL GUIDELINES

MANDATORY! Do not operate your new power chair for the first time without completely readingand understanding this owner’s manual.

Your power chair is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides anextensive variety of products to best fit the individual needs of the power chair user. Please be aware that the finalselection and purchasing decision regarding the type of power chair to be used is the responsibility of the powerchair user, who is capable of making such a decision, and his/her healthcare professional (i.e., medical doctor,physical therapist, etc.).

The contents of this manual are based on the expectation that a mobility device expert has properly fitted thepower chair to the user and has assisted the prescribing healthcare professional and/or the Quantum Rehab Pro-vider in the instruction process for the use of the product.

There are certain situations, including some medical conditions, where the power chair user will need to practiceoperating the power chair in the presence of a trained attendant. A trained attendant can be defined as a familymember or care professional specially trained in assisting a power chair user in various daily living activities.

As you begin using your power chair during daily activities, you will probably encounter situations in which youwill need some practice. Simply take your time and you will soon be in full and confident control as you maneuverthrough doorways, on and off of elevators, up and down ramps, and over moderate terrain.

Below are some precautions, tips, and other safety considerations that will help you become accustomed to oper-ating your power chair safely.

ModificationsPride has designed and engineered your power chair to provide maximum mobility and utility. A wide range ofaccessories is available from your Quantum Rehab Provider to further customize your power chair to better suityour needs and/or preferences. However, under no circumstances should you modify, add, remove, or disable anyfeature, part, or function of your power chair.

WARNING! Do not modify your power chair in any way not authorized by Pride. Do not useaccessories if they have not been tested or approved for Pride products.

Pre-Ride Safety CheckGet to know the feel of your power chair and its capabilities. Pride recommends that you perform a safety checkbefore each use to make sure your power chair operates smoothly and safely.

Perform the following inspections prior to using your power chair:Check for proper tire inflation. Maintain but do not exceed the psi/bar/kPa air pressure rating indicated on eachtire if equipped with pneumatic tires.Check all electrical connections. Make sure they are tight and not corroded.Check all controller connections to the power base. Make sure they are secured properly.Check the brakes. See VII. “Care and Maintenance.”Check battery charge. See VI. “Batteries and Charging.”Ensure the manual freewheel levers are in drive mode before sitting on the power chair.

NOTE: If you discover a problem, contact your Quantum Rehab Provider for assistance.


I I . S A F E T Y

Weight LimitationsYour power chair is rated for a maximum weight capacity. Please refer to the specifications table for this limit.Keep in mind that the maximum weight capacity includes the combined weight of the user and any accessoriesmounted to the power chair.

MANDATORY! Stay within the specified weight capacity of your power chair. Exceeding theweight capacity voids your warranty. Pride will not be held responsible for injuries and/orproperty damage resulting from failure to observe weight limitations.

WARNING! Do not carry passengers on your power chair. Carrying passengers on your powerchair may affect the center of gravity, resulting in a tip or a fall.

Tire InflationIf your power chair is equipped with pneumatic tires, you should check or have the air pressure checked regularly.Proper inflation pressures will prolong the life of your tires and help ensure the smooth operation of your power chair.

WARNING! It is important that the psi/bar/kPa air pressure rating indicated on the tire bemaintained in pneumatic tires at all times. Do not underinflate or overinflate your tires. Lowpressure may result in loss of control, and overinflated tires may burst. Failure to maintain thepsi/bar/kPa air pressure rating indicated on the pneumatic tires at all times may result in tireand/or wheel failure.

WARNING! Inflate your power chair drive tires from a regulated air source with an availablepressure gauge. Inflating your tires from an unregulated air source could overinflate them,resulting in a burst tire.

NOTE: If the tire on your power chair lists the psi rating only, use the following conversion formulas to findthe bar or kPa rating: bar = psi x 0.06895; kPa = psi x 6.89476.

Incline InformationMore and more buildings have ramps with specified degrees of inclination, designed for easy and safe access.Some ramps may have turning switchbacks (180-degree turns) that require you to have good cornering skills onyour power chair.

Proceed with extreme caution as you approach the downgrade of a ramp or other incline.Take wide swings with your power chair’s front wheels around any tight corners. If you do that, the power chair’srear wheels will follow a wide arc, not cut the corner short, and not bump into or get hung up on any railing corners.When driving down a ramp, keep the power chair’s speed adjustment set to the slowest speed setting to ensurea safely controlled descent.Avoid sudden stops and starts.

When climbing an incline, try to keep your power chair moving. If you must stop, start up again slowly and thenaccelerate cautiously. When driving down an incline, set your power chair to the slowest speed setting and drivein the forward direction only. If your power chair starts to move down the incline faster than you anticipated ordesired, allow it to come to a complete stop by releasing the joystick, then push the joystick forward slightly toensure a safely controlled descent.

WARNING! When on any sort of an incline or decline, never place the power chair infreewheel mode, especially while seated on it or standing next to it.

WARNING! When climbing an incline, do not zigzag or drive at an angle up the face ofthe incline. Drive your power chair straight up the incline. This greatly reduces thepossibility of a tip or a fall. Always exercise extreme caution when negotiating anincline.

WARNING! You should not travel up or down a potentially hazardous incline (i.e.,areas covered with snow, ice, cut grass, or wet leaves).

WARNING! Never travel down an incline backward. Doing so may cause the powerchair to tip. Always exercise extreme caution when negotiating an incline.


I I . S A F E T Y

WARNING! If your power chair is equipped with a reclining seatback, do not attempt to negotiateinclines with the seat in a reclined position. Do not attempt to negotiate obstacles with the seatin a reclined position unless an attendant is present to help stabilize the chair. Failure to heedmay result in the power chair tipping over.

WARNING! Even though your power chair is capable of climbing slopes greater than those listedin the product specifications, do not, under any circumstances, exceed the incline guidelines orany other specifications presented in this manual. Doing so could cause instability in your powerchair.

WARNING! Any attempt to climb or descend a slope steeper than that listed in the productspecifications may put your power chair in an unstable position and cause it to tip.

Freewheel ModeYour power chair is equipped with two manual freewheel levers to allow for manual maneuverability by a trainedattendant. For more information about how to place your power chair into and out of freewheel mode, see III.“Your Power Chair.”

WARNING! Do not use your power chair in freewheel mode without an attendantpresent.

WARNING! Do not attempt to personally place your power chair in freewheel modewhile seated on it. Ask an attendant for assistance if necessary.

WARNING! Do not place your power chair in freewheel mode while on an incline ordecline. This could cause the chair to roll uncontrollably on its own.

Braking InformationYour power chair is equipped with two powerful brake systems:

Regenerative—uses electricity to rapidly slow the vehicle when the joystick returns to the center/stop position.Disc Park Brake—activates mechanically after regenerative braking slows the vehicle to near stop, or whenpower is removed from the system for any reason.

Cornering InformationWhile your power chair is equipped with front and rear caster wheels, excessively high cornering speeds can stillcreate the possibility of tipping. Factors which affect the possibility of tipping include, but are not limited to: corner-ing speed, steering angle (how sharply you are turning), uneven road surfaces, inclined road surfaces, riding from anarea of low traction to an area of high traction (such as passing from a grassy area to a paved area—especially at highspeed while turning), and abrupt directional changes. High cornering speeds are not recommended. If you feel thatyou may tip over in a corner, reduce your speed and steering angle (i.e., lessen the sharpness of the turn) to preventyour power chair from tipping.

WARNING! When cornering sharply, reduce your speed and maintain a stable center of gravity.This greatly reduces the possibility of a tip or fall.

Public Streets and Roadways

WARNING! You should not operate your power chair on public streets and roadways. Be awarethat it may be difficult for traffic to see you when you are seated on your power chair. Obey alllocal pedestrian traffic rules. Wait until your path is clear of traffic, and then proceed withextreme caution.


I I . S A F E T Y

Outdoor Driving SurfacesYour power chair is designed to provide optimum stability under normal driving conditions—dry, level surfacescomposed of concrete, blacktop, or asphalt. However, Pride recognizes that there will be times when you willencounter other surface types. For this reason, your power chair is designed to perform admirably on packed soil,grass, and gravel. Feel free to use your power chair safely on lawns and in park areas.

Avoid driving on uneven terrain and/or soft surfaces.Avoid tall grass that can entangle the running gear.Avoid loosely packed gravel and sand.Do not use your power chair in fresh or salt water.Do not use your power chair at the edge of a stream, lake, or ocean.If you feel unsure about a driving surface, avoid that surface.

Inclement Weather PrecautionsExposure of your power chair to inclement weather conditions should be avoided whenever possible. If suddenlycaught up in rain, snow, severe cold or heat while operating your power chair, proceed to shelter at the earliestopportunity. Thoroughly dry your power chair before storing, charging, or operating your power chair.

PROHIBITED! Operating in rain, snow, salt, mist/spray conditions, and on icy/slippery surfacescan have an adverse effect on the electrical system. Maintain and store your power chair in adry and clean condition.

WARNING! Prolonged exposure to hot or cold conditions may affect the temperature ofupholstered and non-upholstered items on the power chair, possibly resulting in skin irritation.Exercise caution when using your power chair in extremely hot or cold conditions or whenexposing your power chair to direct sunlight for prolonged periods of time.

Stationary Obstacles (Steps, Curbs, etc.)Proceed with extreme caution when driving near raised surfaces, unprotected ledges, and/or drop-offs (curbs,porches, stairs, etc.). Be sure your power chair is traveling perpendicular to any curb you may be required to navigate.

To navigate up over a curb or stationary obstacle:1. Approach the curb or obstacle slowly, and make sure the power chair is traveling perpendicular to the obstacle.

See figure 1.2. Increase the forward speed just before the front wheels come in contact with the obstacle.3. Reduce the forward speed only after the rear wheels have cleared the obstacle.

To navigate down a curb or stationary obstacle:1. Approach the curb or obstacle slowly, and make sure the power chair is traveling perpendicular to the obstacle.

See figure 1.2. Reduce the forward speed just before the front wheels come in contact with the obstacle.3. Increase the forward speed only after the rear wheels have cleared the obstacle and you are once again on a level surface.

WARNING! Even though your power chair may be capable of handling greater obstacles, Priderecommends that you do not attempt to negotiate a curb that has a height greater than 2 in.(5 cm). Doing so could cause instability in your power chair.

WARNING! Do not attempt to have your power chair proceed backward down any step, curb, orother obstacle. This may cause the power chair to tip.


I I . S A F E T Y

Figure 1. Correct Curb Approach Figure 2. Incorrect Curb Approach

Stairs and EscalatorsPower chairs are not designed to travel up or down stairs or escalators. Always use an elevator.

WARNING! Never use your power chair to negotiate steps or escalators.

DoorsDetermine if the door opens toward or away from you.Drive your power chair gently and slowly forward to push the door open. Or drive your power chair gentlyand slowly backward to pull the door open.

ElevatorsModern elevators have a door edge safety mechanism that, when pushed, reopens the elevator door(s).

If you are in the doorway of an elevator when the door(s) begin to close, push on the rubber door edge or allowthe rubber door edge to contact the power chair and the door will reopen.Use care that pocketbooks, packages, or power chair accessories do not become caught in elevator doors.

Lift Systems/Elevation ProductsIf you will be transporting your power chair during travel, you may find it necessary to use a vehicle-mounted liftsystem or elevation product to aid in transportation. Pride recommends that you closely review the warnings,instructions, specifications, and safety information set forth by the manufacturer of the lift/elevation productbefore using that product.

WARNING! Not all lift systems/elevation products are rated for use with an occupied mobilitydevice. Pride recommends that you do not remain seated in your power chair when it is beingused in connection with any type of lift system/elevation product unless:

That product is rated for occupied use by the manufacturer.You are able to occupy your mobility device in strict conformity with the warnings,instructions, specifications, and safety guidelines set forth by the manufacturer.

WARNING! Always turn off the power to the controller when you are being transferred via anelevation product. Failure to do so may result in accidental joystick contact, resulting inunintended movement and personal injury or product damage.

Motor Vehicle TransportPride recommends that you do not remain seated in your power chair while traveling in a motor vehicle. Thepower chair should be stowed in the trunk of a car or in the back of a truck or van with batteries removed and/orproperly secured. In addition, all removable power chair parts, including the armrests, seat, front riggings, con-troller, and shrouds should be removed and/or properly secured during motor vehicle transport.


I I . S A F E T Y

WARNING! Pride does not recommend using the power chair as a seat in a motor vehicle. Thepower chair user should transfer into the vehicle seat and use the vehicle-installed belt restraintsystem if and whenever feasible.

WARNING! Always be sure your power chair and its batteries are properly secured when it isbeing transported. Batteries should be secured in an upright position and protective caps shouldbe installed on the battery terminals. Batteries should not be transported with any flammable orcombustible items.

Positioning BeltsYour Quantum Rehab Provider, therapist(s), and other healthcare professionals are responsible for determiningyour requirement for a positioning belt in order to operate your power chair safely.

WARNING! If you require a positioning belt to safely operate your power chair, make sure it isfastened securely in order to reduce the possibility of a fall from the power chair.

WARNING! The positioning belt is not designed for use as a seat belt in a motor vehicle. Nor isyour power chair suitable for use as a seat in any vehicle. Anyone traveling in a vehicle shouldbe properly belted into seats approved by the vehicle manufacturer.

BatteriesIn addition to following the warnings below, be sure to comply with all other battery handling information. Formore information about your power chair’s batteries, see VI. “Batteries and Charging.”

MANDATORY! Battery posts, terminals, and related accessories contain lead andlead compounds. Wear goggles and gloves when handling batteries and wash handsafter handling.

WARNING! Power chair batteries are heavy. See specifications table. If you areunable to lift that much weight, be sure to get help. Use proper lifting techniques andavoid lifting beyond your capacity.

WARNING! Always protect the batteries from freezing and never charge a frozenbattery. Charging a frozen battery may result in damage to the battery.

WARNING! Connect your battery harnesses in the proper manner. RED (+) cablesmust be connected to positive (+) battery terminals/posts. BLACK (-) cables must beconnected to negative (-) battery terminals/posts. Protective caps should be installedover all battery terminals. REPLACE cables immediately if damaged.

Removable Parts

WARNING! Do not attempt to lift or move a power chair by any of its removable parts, includingthe armrests, seat, front riggings, controller, and shrouds. Pride recommends use of only solid,non-removable frame components to lift or move your power chair.

Preventing Unintended Movement

WARNING! If you anticipate being seated in a stationary position for an extended period of time,turn off the power. This will prevent unexpected motion from inadvertent joystick contact. This willalso eliminate the possibility of unintended chair movement from electromagnetic (EM) sources.


I I . S A F E T Y

Reaching and BendingNever reach, lean, or bend while driving your power chair. If it is absolutely necessary to reach, lean, or bendwhile seated on your power chair, it is important to maintain a stable center of gravity and keep the power chairfrom tipping. Pride recommends that the power chair user determine his/her personal limitations and practicebending and reaching in the presence of a qualified healthcare professional.

WARNING! Do not bend, lean, or reach for objects if you have to pick them up fromthe floor by reaching down between your knees or if you have to reach over the backof the seat. Movements such as these may change your center of gravity and theweight distribution of the power chair, possibly causing your power chair to tip.

WARNING! Keep your hands away from the tires when driving. Be aware that loosefitting clothing can become caught in drive tires.


WARNING! Before transferring, turn off the power to the controller to prevent unintendedmovement.

WARNING! Before transferring, position yourself as far back as possible in the power chair seatto prevent the power chair from tipping forward during transfer.

WARNING! Avoid putting all of your weight on the power chair armrests and do not use thearmrests for weight bearing purposes, such as transfers. Such use may cause the power chairto tip, resulting in a fall from the power chair and personal injury.

WARNING! The controller and controller bracket are non-load bearing items on your power chair.Do not use the controller or controller bracket for weight bearing purposes, such as transfers.Such use may cause damage to these components, resulting in a fall from the power chair andpersonal injury.

WARNING! Avoid putting all of your weight on the front riggings. Such use may cause the powerchair to tip.

Figure 3. Ideal Transfer Position

TransfersTransferring onto and off of your power chair requiresa good sense of balance. Always have an attendant orhealthcare professional present while learning to prop-erly transfer yourself.

To eliminate the possibility of injury, Pride recom-mends that you or a trained attendant perform the fol-lowing tasks before attempting a transfer:

Ensure your power chair is not in freewheel mode.See III. “Your Power Chair.”Turn the caster wheels toward the transfer destina-tion to improve power chair stability during transfer.Make sure both armrests are flipped up or removedfrom your power chair.Flip up the foot platform or move the leg restsaside; this will help to keep your feet from gettingcaught on the front rigging during the transfer.Reduce the distance between your power chair andthe object you are transferring onto.

I I . S A F E T Y


Prescription Drugs/Physical LimitationsUsers must exercise care and common sense when operating a power chair. This includes awareness of safetyissues when taking prescribed or over-the-counter drugs or when the user has specific physical limitations.

WARNING! Consult your physician if you are taking prescribed or over-the-counter medication orif you have certain physical limitations. Some medications and limitations may impair yourability to operate your power chair in a safe manner.

Alcohol/SmokingThe power chair user must exercise care and common sense when operating his/her power chair. This includesawareness of safety issues while under the influence of alcohol or while smoking.

WARNING! Do not operate your power chair while you are under the influence of alcohol, as thismay impair your ability to operate your power chair in a safe manner.

WARNING! Pride strongly recommends that you do not smoke cigarettes while seated in yourpower chair, although the power chair has passed the necessary testing requirements forcigarette smoking. You must adhere to the following safety guidelines if you decide to smokecigarettes while seated in your power chair.

Do not leave lit cigarettes unattended.Keep ashtrays a safe distance from the seat cushions.Always make sure cigarettes are completely extinguished before disposal.

Flammability Precautions

WARNING! Even though the plastics on your power chair have passed the applicable flammabilitystandards, Pride recommends that you do not expose your power chair to open flames.

WARNING! Replace worn or damaged upholstery immediately to reduce the risk of fire hazard.

WARNING! Be aware that washing of upholstered items may reduce the resistance toflammability of the fabric.

Electromagnetic and Radio Frequency Interference (EMI/RFI)

WARNING! Laboratory tests have shown that electromagnetic and radio frequency waves canhave an adverse effect on the performance of electrically-powered mobility vehicles.

Electromagnetic and Radio Frequency Interference can come from sources such as cellular phones, mobile two-way radios (such as walkie-talkies), radio stations, TV stations, amateur radio (HAM) transmitters, wireless com-puter links, microwave signals, paging transmitters, and medium-range mobile transceivers used by emergencyvehicles. In some cases, these waves can cause unintended movement or damage to the control system. Everyelectrically-powered mobility vehicle has an immunity (or resistance) to EMI. The higher the immunity level, thegreater the protection against EMI. This product has been tested and has passed at an immunity level of 20 V/m.

WARNING! Be aware that cell phones, two-way radios, laptops, electricity generators or highpower sources, and other types of radio transmitters may cause unintended movement of yourelectrically-powered mobility vehicle due to EMI. Exercise caution when using any of theseitems while operating your mobility vehicle and avoid coming into close proximity of radio andTV stations.

WARNING! The addition of accessories or components to the electrically-powered mobilityvehicle can increase the susceptibility of the vehicle to EMI. Do not modify your power chair inany way not authorized by Pride.

WARNING! The electrically-powered mobility vehicle itself can disturb the performance of otherelectrical devices located nearby, such as alarm systems.

NOTE: For further information on EMI/RFI, go to the Resource Center on www.pridemobility.com. If unin-tended motion or brake release occurs, turn your power chair off as soon as it is safe to do so. Contact yourauthorized Quantum Rehab Provider to report the incident.


MANUALFREEWHEEL LEVER

DRIVE WHEEL

I I I . Y O U R P O W E R C H A I R

THE Q6 EDGE HD POWER CHAIRYour power chair has two main assemblies: the seat assembly and the power base assembly. See figure 4. Typically,the seat assembly includes the armrests, seatback, and seat base. The power base assembly includes two motor/brakeassemblies, two drive wheels, four caster wheels, two batteries, and wiring harnesses. See figures 4, 5, and 6.

Figure 4. The Q6 Edge HD Power Chair

SEATBACK

CASTER WHEEL

JOYSTICK

FRONT RIGGING(FOOT PLATFORM SHOWN)

SEAT BASE

CONTROLLER

CASTER WHEEL

ARMREST

ARMREST

POWER BASE ASSEMBLY

SEAT ASSEMBLY

MANUALFREEWHEELLEVER


Figure 5. The Q6 Edge HD Power Base

TRAPEZE BARS

FRONT COVER

REAR SHROUD

Electrical ComponentsThe electrical components consist of the controller assembly, the batteries, and the motors. The batteries, motors,and controller power module (if equipped) are located on the power base assembly. The controller is located onthe seat assembly. Connectivity between the controller and the motors, batteries, and the battery charger is pro-vided by one or more wiring harnesses. See figure 6.

Controller Harness Connector: The controller harness connector is where the controller plugs into the powerbase. Each controller uses a different type of harness. Regardless of which type of controller is used, the harnessmust be secured to the seat assembly and not allowed to drag on the floor.

Motor Connectors: This is where the controller connects to the motors.

Battery Connector: This is where the controller connects to the batteries.

Controller Power Module: This enables the controller to communicate with the batteries and the motors.



Main Circuit Breaker (located on the rear main frame): The main circuit breaker is a safety feature built intoyour power chair. When the batteries and the motors are heavily strained (e.g., from excessive loads), the maincircuit breaker trips to prevent damage to the motors and the electronics. If the circuit trips, allow your power chairto “rest” for approximately one minute. The circuit breaker will reset itself. Turn on the controller and continuenormal operation. If the main circuit breaker continues to trip repeatedly, contact your Quantum Rehab Provider.


TO MOTORCONNECTOR

TO MOTORCONNECTOR

TO BATTERYCONNECTORS

MAIN CIRCUIT BREAKER

QUICK RELEASEBATTERY CONNECTORS

Figure 6. Q6 Edge HD Electrical Components

CONTROLLER POWER MODULE

CONTROLLER CONNECTOR


MANUAL FREEWHEEL LEVERMANUAL FREEWHEEL LEVER


Manual Freewheel LeversFor your convenience, your power chair is equipped with a manual freewheel lever mounted on each motor. Thelevers allow you to disengage the drive motors and maneuver the chair manually.

WARNING! Do not use the power chair while the drive motors are disengaged! Do notdisengage the drive motors when the power chair is on an incline, as the unit couldroll on its own! Only engage the freewheel mode when on a level surface.

WARNING! It is important to remember that when your power chair is in freewheelmode, the braking system is disengaged.

To operate the manual freewheel levers:1. Push down both manual freewheel levers for freewheel mode (drive motor disengaged). See figure 7.2. Pull up both manual freewheel levers for drive mode (drive motor engaged). See figure 8.

NOTE: You must turn off the power before disengaging the drive motors; otherwise, you may get an error codeon the controller. To clear this code, turn off the controller and place the power chair in drive mode. Then, turnon the controller. The error message should be cleared. If it is not, contact your Quantum Rehab Provider.

NOTE: The power chair will be significantly easier to push with the power off.

WARNING! Avoid applying excessive force to the manual freewheel levers.

WARNING! Do not use your foot to operate the manual freewheel levers. Do not stand on themanual freewheel levers. Applying excessive force to the manual freewheel levers may result indamage to the freewheel levers, motors, and brakes.

WARNING! Do not use the freewheel lever handles as tie-down points to secure this product.

Figure 8. Drive Mode (Drive Engaged)Figure 7. Freewheel Mode (Drive Disengaged)

I V . A S S E M B L Y

INITIAL ASSEMBLYYour power chair may require some assembly either before initial use or after transportation. It may also requiredisassembly to make some comfort adjustments. Figure 9 details those parts of the power chair that are designedto be disassembled and assembled by an end user or by a qualified caregiver before using the product or makingcomfort adjustments.

NOTE: Any nylon insert lock nut removed during the disassembly or adjustment of the power chair must bereplaced with a new nut. Nylon insert lock nuts should not be reused as it may cause damage to the nylon insert,resulting in a less secure fit. Replacement nylon insert lock nuts are available at local hardware stores orthrough your Quantum Rehab Provider.


Figure 9. Q6 Edge HD Assembly View

ARMREST ANGLE ADJUSTMENT

FOOT PLATFORM HEIGHT/DEPTH ADJUSTMENT

SEAT HEIGHT/ANGLE ADJUSTMENT

CONTROLLER POSITION

FOOT PLATFORMANGLE ADJUSTMENT


Figure 10. Universal Mounting System and Contour Seat

REAREXTRUSION

FRONT EXTRUSION

SEAT LATCH SAFETY

TRAPEZE BARS

Seat InstallationIt may be necessary to install the seat either prior toinitial operation or after transporting your power chair.Contour seats are attached to the power base with theUniversal Mounting System (UMS). The UMS con-sists of universal parts that may be attached to the seat,regardless of seat width or seat depth. The two maincomponents are aluminum extrusions mounted to theseat base. These extrusions attach to a pair of trapezebars that are mounted to the power base. See figure 10.

NOTE: If your power chair is equipped with a Spe-cialty Seat, Synergy Seat, or a TRU-Balance PowerPositioning System, refer to the information providedin separate manuals.

WARNING! Do not pick up the seatframe by the armrests. They are free topivot, and you may lose control of theseat if they do so.

To install the seat:1. Tilt the seat back and slide the rear extrusion onto

the rear trapeze bar. See figure 10.2. Lower the front extrusion onto the front trapeze bar

until the seat locks into place.3. Flip the seat latch safety down.

WARNING! Make sure the seat latchsafety is flipped down before usingyour power chair.

4. Install the controller and route the harness to theback of the power base. See figure 11 or 12.

MANDATORY! Prevent controllerharness damage! Avoid routing thecontroller harness on the outside ofthe armrest pad. Route the harnessunder the armrest or toward the insideof the armrest pad. Use correct tie-down points for controller harness toprevent the harness from gettingcaught in the drive tires, pinched in theseat frame, or damaged when passingthrough doorways.

5. Plug the controller connector into the rear of thepower base. See figure 6.

6. Secure the controller harness to the armrestreceiver with wire ties. See figure 12.


Figure 11. Controller Harness Routing on a Synergy Seat



Figure 13. Transit Securement Brackets

Figure 12. Controller Harness Routing on a ContourSeat

WIRE TIES

TO POWER BASE

Power Chair Securement PointsThis power chair may be equipped with four (4) tie-down points for the purpose of securing the unoccu-pied power chair during motor vehicle transport. Eachtie-down point is clearly labeled for this purpose.

To secure a power chair equipped with tie-downpoints:

Always secure the power chair in a forward-facingposition in the vehicle.Attach the four tie-down straps only to designated,labeled transit securement points indicated byanchor symbols on the power chair. See figure 13.Tighten the straps to sufficiently remove all theslack.Never attach tie-downs to adjustable, moving, orremovable parts of the power chair such as arm-rests, front riggings, and wheels.Position the anchor points for the rear tie-downstraps directly behind the rear securement points onthe power chair. The front tie-down straps shouldbe anchored to floor points that are spaced widerthan the power chair to provide increased stability.See figure 14.

MANDATORY! The power chair shouldbe used as indicated in themanufacturer’s instructions. If youhave any questions about the properuse of your power chair, contact yourQuantum Rehab Provider.

SECUREMENT BRACKETS

SECUREMENT BRACKETS



Figure 14. Unoccupied Transit System Securement Points

FRONTOF VEHICLE

V . C O M F O R T A D J U S T M E N T S

You may need the following to make comfort

COMFORT ADJUSTMENTSAfter becoming familiar with your power chair’s operation, you may find the need to make some adjustments toincrease your comfort, such as seat height and angle, armrest width, armrest angle and height, foot platformheight, depth, and angle, and controller position.

NOTE: If your power chair is equipped with a Specialty Seat, Synergy Seat, or TRU-Balance Power Position-ing System, refer to the seat adjustment information contained in separate manuals. If your power chair isequipped with a contoured seating system, refer to the following information.

WARNING! The center of gravity of your power chair was factory set to a position that meets theneeds of the demographic majority of users. Your Quantum Rehab Provider has evaluated yourpower chair and made any necessary adjustments to suit your specific requirements. Do notchange your seating configuration without first contacting Pride Mobility Products or yourQuantum Rehab Provider.

WARNING! Some power chair components are heavy. You may need assistance to lift or carrythem. Please refer to the specifications table for specific component weights before youdisassemble the power chair.

WARNING! Remove the occupant from the power chair before making any adjustments.

Figure 15. Seat Height/Angle Adjustment

HARDWARE

TRAPEZE BARS

SEATINTERFACEWELDMENT

HARDWARE

adjustments:metric/standard socket set and ratchetadjustable wrenchmetric/standard hex key setthread lock

Seat Height and Seat Angle AdjustmentIf your power chair is not equipped with a transitsecurement system, you can change the seat height toone of three positions by raising the front and rear tra-peze bars. If you raise or lower only one trapeze bar(front or rear), you can also change the seat base angle(dump).

MANDATORY! If your power chair isequipped with a transit securementsystem and any adjustment to the seatheight or seat angle is necessary,contact your Quantum Rehab Provider.These comfort adjustment can only bemade by a Quantum Rehab Provider.

To change the seat height:1. Turn off the power to the controller.2. Make sure the power chair is in drive mode.3. Unplug the controller connector(s) from the power

base. See figure 6.4. Flip up the seat latch safety. See figure 10.5. Squeeze the seat latch and release the seat from the

front trapeze bar.6. Slide the seat forward and remove it from the

power base.


Figure 16. Seat Position Adjustment


SEAT MOUNTING HOLES

7. Remove the hardware that attaches the trapeze barsto the seat interface weldments. See figure 15.

8. Move the trapeze bars up or down to the desiredheight.

NOTE: Change the seat dump by raising or loweringonly one trapeze bar (front or rear).

9. Reinstall the hardware.10. Reinstall the seat.11. Reconnect the controller to the power base.

Seat PositionYou can move the seat forward or rearward by chang-ing the extrusion mounting position.

To change the position:1. Turn off the power to the controller.2. Make sure the power chair is in drive mode.3. Unplug the controller connector(s) from the power

base.4. Remove the seat from the power base.5. Remove both extrusions from the bottom of the seat. 6. Reposition the extrusions on a different set of

mounting holes. You must move both extrusionsthe same number of holes either forward or back-wards. See figure 16.

7. Fasten the extrusions back onto the bottom of theseat.

8. Reinstall the seat.9. Reconnect the controller to the power base.

Manual Recline Seatback AdjustmentIf your power chair is equipped with a reclining seat,you can adjust the seatback angle with the seatbackrelease lever. The lever is located on the right side ofthe seat base.

To adjust the recline angle:1. Pull up on the seatback release lever.2. Lean forward or backwards to the desired position.3. Release the lever.



ARMREST KNOB

JAM NUT

Figure 17. Seatback/Armrest Adjustment

SEATBACK ANGLE ADJUSTING SCREW

ARMREST HEIGHT ADJUSTING SETSCREWS

ARMREST ANGLE ADJUSTINGSCREW

Seatback Angle AdjustmentIf your power chair is equipped with an adjustable seat-back, you can adjust it to four (4) different angles: 90°,102°, 105°, or 107°.

To adjust the seatback angle:1. Remove the adjusting screws from each seat hinge.

See figure 17.2. Set the seatback at the desired angle.3. Reinstall the adjusting screws to each seat hinge

and tighten.

Armrest Width AdjustmentYou can change each armrest’s width independently ofthe other.

NOTE: Changing the armrest width may increase theoverall width of your power chair.

To change the armrest width:1. Locate the two armrest knobs on each side of the

armrest receiver bracket. See figure 17.2. Loosen the knobs.3. Slide the armrests in or out to the desired width.4. Tighten the knobs.

Armrest Angle AdjustmentTo change the armrest angle:1. Lift the armrest straight up so that it is perpendicu-

lar to the floor. See figure 17.2. Loosen the jam nut.3. Turn the adjusting screw to raise or lower the front

of the armrest.4. Tighten the jam nut to lock the adjusting screw into

place.

Armrest Height AdjustmentTo change the armrest height:1. Loosen the two setscrews located on the armrest

receiver. See figure 17.2. Raise or lower the armrest to the desired height.3. Tighten the setscrews to secure the armrest.



Figure 18. Underside of Armrest

SETSCREW

CONTROLLER BRACKET

Controller PositionYou can move the controller in toward or out awayfrom the armrest, or change the position of the control-ler for either left-hand or right-hand use.

WARNING! Do not place the controllerharness so that it can be pinched in theseat frame or the power base frame.

To extend the controller:1. Flip up the armrest so it is perpendicular to the

floor.2. Loosen the setscrew on the controller bracket. See

figure 18.3. Slide the controller into or out of the armrest to the

desired position.4. Tighten the setscrew to secure the controller.

To change the controller position:1. Turn off the power to the controller.2. Unplug the controller connector(s) from the power

base.3. Remove any wire ties securing the controller har-

ness to the armrest.4. Flip up the armrest so it is perpendicular to the floor.5. Loosen the setscrew on the controller bracket.6. Slide the controller out of the armrest.7. Loosen the setscrew in the other armrest.8. Place the controller in the other armrest.9. Tighten the setscrews in both armrests.10. Route the controller harness to the back of the

power base and plug in the controller.11. Secure the controller harness to the armrest with

wire ties. See figure 12.

NOTE: If your power chair is equipped with a Spe-cialty Seat, Synergy Seat, or TRU-Balance PowerPositioning System, refer to the information providedin supplemental manuals provided with your seatingsystem.



Foot Platform Height AdjustmentThe foot platform height is easily adjusted to several different heights.

To raise or lower the foot platform:1. Remove the hardware from the foot platform bracket. See figure 19.2. Raise or lower the foot platform to the desired height.3. Reinstall the hardware into the foot platform bracket and tighten.

Foot Platform Depth AdjustmentYou can adjust the depth of the foot platform.

To adjust the foot platform depth:1. Remove the hardware from the foot platform bracket. See figure 19.2. Move the foot platform in or out to the desired depth.3. Reinstall the hardware into the foot platform bracket and tighten.

Foot Platform Angle AdjustmentYou can adjust the angle of the foot platform.

To adjust the foot platform angle:1. Flip up the foot platform and locate the screw. See figure 19.2. Turn the screw to raise or lower the front of the foot platform.


FOOT PLATFORM BRACKET

HARDWARE

SCREW

Figure 19. Foot Platform Adjustment


To adjust the positioning belt for operator comfort:1. Once seated, insert the metal tab on one side of the belt into the plastic housing on the opposite side until you

hear a click. See figure 20.2. Pull the excess strap attached to the metal tab until it is secure, but not so tight as to cause discomfort.

To release the positioning belt:1. Press the push button mechanism on the plastic housing.

MANDATORY! Make sure the positioning belt is properly secured to the power chair and isadjusted for operator comfort before each use.

MANDATORY! Inspect the positioning belt for loose or damaged parts before each use of thepower chair. If you discover a problem, contact your Quantum Rehab Provider for maintenanceand repair.

Positioning BeltYour power chair may be equipped with a positioningbelt that can be adjusted for operator comfort. See fig-ure 20. The positioning belt is designed to support theoperator so that he/she does not slide down or forwardin the seat. The positioning belt is not designed for useas a restraining device.

WARNING! The positioning belt is notdesigned for use as a seat belt in amotor vehicle. Nor is your power chairsuitable for use as a seat in anyvehicle. Anyone traveling in a vehicleshould be properly belted into seatsapproved by the vehicle manufacturer.

WARNING! The positioning belt shouldbe secured at all times. Never allowthe positioning belt to hang or drag onthe floor as it may become entangled.

To install the positioning belt:1. Remove the rearmost screw that holds the seat

hinge to the seat base on both the left and right seathinges.

2. Insert the screw through the supplied washer,through the positioning belt and into the seat basefor each side of the power chair seat.

3. Tighten both screws.


Figure 20. Positioning Belt Adjustment

V I . B A T T E R I E S A N D C H A R G I N G

BATTERIES AND CHARGINGThe Q6 Edge HD uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenancefree. Since they are sealed, there is no need to check the electrolyte (fluid) level. Deep-cycle batteries are designedto handle a longer and deeper discharge. Though they are similar in appearance to automotive batteries, they arenot interchangeable. Automotive batteries are not designed to handle a long, deep discharge, and also are unsafefor use in power chairs.


WARNING! Contact your Quantum Rehab Provider if you have any questions regardingthe batteries in your power chair.

PROHIBITED! Always use two batteries of the exact same type, chemistry, and amp-hour (Ah) capacity. Refer to specifications table in this manual and in the manualsupplied with the battery charger for recommended type and capacities.

The battery charger is essential in providing long life for your power chair batteries. It is designed to optimizeyour power chair’s performance by charging the batteries safely, quickly, and easily.

PROHIBITED! Removal of grounding prong can create electrical hazard. Ifnecessary, properly install an approved 3-pronged adapter to an electrical outlethaving 2-pronged plug access.

PROHIBITED! Never use an extension cord to plug in your battery charger. Plug thecharger directly into a properly wired standard electrical outlet.

PROHIBITED! Do not allow unsupervised children to play near the power chair whilethe batteries are charging. Pride recommends that you do not charge the batterieswhile the power chair is occupied.

MANDATORY! Read the battery charging instructions in this manual and in themanual supplied with the battery charger before charging the batteries.

WARNING! Explosive gases may be generated while charging the batteries. Keep thepower chair and battery charger away from sources of ignition such as flames orsparks and provide adequate ventilation when charging the batteries.

WARNING! You must recharge the power chair batteries with the supplied off-boardbattery charger. Do not use an automotive-type battery charger.

WARNING! Inspect the battery charger, wiring, and connectors for damage beforeeach use. Contact your authorized Quantum Rehab Provider if damage is found.

WARNING! Do not attempt to open the battery charger case. If the battery chargerdoes not appear to be working correctly, contact your authorized Quantum RehabProvider.

WARNING! Be aware that the battery charger case may become hot during charging.Avoid skin contact and do not place on surfaces that may be affected by heat.

WARNING! If the battery charger is equipped with cooling slots, then do not attemptto insert objects through these slots.

WARNING! If your battery charger has not been tested and approved for outdoor use,then do not expose it to adverse or extreme weather conditions. If the batterycharger is exposed to adverse or extreme weather conditions, then it must beallowed to adjust to the difference in environmental conditions before use indoors.Refer to the manual supplied with the battery charger for more information.



Figure 21. Battery Charging

To charge the batteries using the off-board charger:1. Position your power chair next to a standard electrical

outlet.2. Be certain the controller power is turned off and the

power chair is in drive mode.3. Plug the off-board charger into the off-board charger/

programming socket on the controller. See figure 21.4. Plug the off-board charger into the electrical outlet.

NOTE: The LED lights on the charger indicate differentcharger conditions at various times: charger power on,charging in progress, and charging complete. Refer tothe manual supplied with the charger for a completeexplanation of these indicators.

5. When the batteries are fully charged, unplug the off-board charger from the electrical outlet and then fromthe controller.

XLR

Battery Break-inTo break in new batteries for maximum efficiency:1. Fully recharge any new battery prior to its initial use. This brings the battery up to about 90% of its peak

performance level.2. Operate your power chair throughout the house and yard. Move slowly at first, and do not travel too far until

you become accustomed to the controls and break in the batteries.3. Give the batteries another full charge of 8 to 14 hours and operate your power chair again. The batteries will

now perform at over 90% of their potential.4. After four or five charging cycles, the batteries will top off at 100% charge and last for an extended period.

Frequently Asked Questions (FAQs)

How does the charger work?The battery charger takes the standard electrical outlet voltage of 120 VAC (alternating current) and converts itto 24 VDC (direct current). The power chair batteries use direct current to run your power chair. When the batteryvoltage is low, the charger works harder to charge the battery. As the battery voltage approaches full charge, thecharger does not work as hard to complete the charging cycle. When the battery is fully charged, the amperagefrom the charger is nearly at zero. This is how the charger maintains a charge but does not overcharge the battery.

Can I use a different battery charger?You should use the charger supplied with the power chair. It is the safest, most efficient tool to charge the batteries.We do not recommend using other types of chargers (e.g., an automotive battery charger).

NOTE: Your power chair’s charger will not operate after the batteries have been discharged to nearly zerovoltage. If this happens, call your Quantum Rehab Provider for assistance.

How often must I charge the batteries?Many factors come into play when deciding how often to charge the batteries. You may use your power chair allday on a daily basis or you may not use it for weeks at a time.



Daily UseIf you use your power chair on a daily basis, charge the batteries as soon as you are finished using your powerchair. Your power chair will be ready each morning to give you a full day’s service. It is recommended thatyou charge the batteries 8 to 14 hours after daily use.

Infrequent UseIf you use your power chair infrequently (once a week or less), you should charge the batteries at least onceper week for 12 to 14 hours.

NOTE: Keep your batteries fully charged and avoid deeply discharging your batteries. Refer to the manualsupplied with the battery charger for charging instructions.

How can I get maximum range or distance per charge?Rarely do you have an ideal driving situation such as smooth, flat, hard terrain with no wind, hills, or curves. Moreoften you are presented with hills, sidewalk cracks, uneven and loosely packed surfaces, curves, and wind. All ofthese factors will affect the distance or running time per battery charge. Below are a few suggestions for obtainingthe maximum range per charge:

Always charge the batteries fully prior to your trip.Plan your trip in advance to avoid inclines if possible.Limit baggage weight to essential items.Try to maintain an even speed and avoid stop-and-go driving.

What type of batteries should I use?We recommend deep-cycle batteries that are sealed and maintenance free. Both AGM and Gel-Cell are deep-cyclebatteries that are similar in performance. Refer to the specifications table for more information regarding thebatteries used with your power chair.

WARNING! Corrosive chemicals contained in batteries. Use only AGM or Gel-Cellbatteries to reduce the risk of leakage or explosive conditions.

Why do my new batteries seem weak?Deep-cycle batteries employ a much different chemical technology than that used in car batteries, nickel-cadmium(nicads), or in other common battery types. Deep-cycle batteries are specifically designed to provide power, draindown their charge, and then accept a relatively quick recharge. AGM and Gel-Cell batteries should be charged asoften as possible. They do not have a “memory” like nickel-cadmium batteries.

We work closely with our battery manufacturer to provide a battery that best suits your power chair’s specificdemands. Fresh batteries arrive regularly at Pride and are promptly shipped with a full charge. During shipping,the batteries encounter temperature extremes that may influence initial performance. Heat robs the charge fromthe battery, and cold slows the power available and extends the time needed to recharge the battery (just as witha car battery).

It might take a few days for the temperature of the battery to stabilize and adjust to its new ambient temperature.More importantly, it will take a few “charging cycles” (a partial drain—then a full recharge) to establish thecritical chemical balance that is essential to the battery’s peak performance and long life. It will be well worth itto take the time to break in your battery properly.



How can I ensure maximum battery life?A fully charged deep-cycle battery will provide reliable performance and extended battery life. Keep your powerchair’s batteries fully charged whenever possible. Batteries that are regularly and deeply discharged, infrequentlycharged, or stored without a full charge may be permanently damaged, causing unreliable power chair operationand limited battery life.

NOTE: The useful life of a battery is quite often a reflection of the care it receives.

How should I store my power chair and its batteries?If you do not use your power chair regularly, we recommend maintaining battery vitality by charging the batteriesat least once per week.

If you do not plan on using your power chair for an extended period, fully charge the batteries prior to storage.Disconnect the battery harnesses and store the power chair in a warm, dry environment. Avoid temperatureextremes, such as freezing and excessively hot conditions, and never attempt to charge a frozen battery. A cold orfrozen battery should be warmed for several days prior to recharging.

What about public transportation?AGM and Gel-Cell batteries are designed for application in power chairs and other mobility vehicles. Thesebatteries are Federal Aviation Administration (FAA) approved, allowing safe transportation on aircraft, buses, andtrains, as there is no danger of spillage or leakage. We suggest you contact the carrier’s ticket counter in advanceto determine that carrier’s specific requirements.

What about shipping?If you wish to use a freight company to ship your power chair to your final destination, repack your power chairin the original shipping container and ship the batteries in separate boxes.


V I I . C A R E A N D M A I N T E N A N C E

CARE AND MAINTENANCEYour Q6 Edge HD is a sophisticated power chair. Like any motorized vehicle, it requires routine maintenancechecks. You can perform some of these checks, but others require assistance from your Quantum Rehab Provider.Preventive maintenance is very important. If you follow the maintenance checks in this section as scheduled, youcan help ensure that your power chair gives you years of trouble-free operation. If you have any doubt as to yourpower chair’s care or operation, contact your Quantum Rehab Provider.

WARNING! Do not service the power chair when the seat is occupied.

Your power chair, like most electrical equipment, is susceptible to damage from the elements. Avoid damp areasof any kind.

WARNING! Direct or prolonged exposure to water or dampness could cause the powerchair to malfunction electronically and mechanically. Water can cause electricalcomponents to corrode and the chair's frame to rust. Power chairs should be examinedperiodically for signs of corrosion caused by water exposure, bodily fluid exposure, orincontinence. Damaged components should be replaced or treated immediately.

Should your power chair come in contact with water:1. Dry your power chair as thoroughly as possible with a towel.2. Allow your power chair to sit in a warm, dry place for 12 hours to allow unseen water to evaporate.3. Check the joystick operation and the brakes before using your power chair again.4. If any inconsistencies are found, take your power chair to a Quantum Rehab Provider. Power chairs that are

frequently exposed to sources of water, such as incontinence, should be inspected often for corrosion andelectronic components may need to be replaced frequently.

TemperatureSome of the parts of your power chair are susceptible to extreme changes in temperature. Always keep yourpower chair between the temperatures of 18°F (-8°C) and 122°F (50°C).In extremely cold temperatures the batteries may freeze. The specific temperature at which they freeze dependson a number of factors, such as battery charge, usage, and composition of the batteries (e.g., AGM or Gel-Cell). Temperatures above 122°F (50°C) may cause your power chair to operate at a reduced speed. This reducedspeed is a safety feature built into the controller that helps prevent damage to the motor and other electricalcomponents.

General GuidelinesAvoid knocking or bumping the controller, especially the joystick.Avoid prolonged exposure of your power chair to extreme conditions, such as heat, cold, or moisture.Keep the controller clean.Check all connectors to ensure that they are all tight and secured properly. Make sure pneumatic tires are inflated to the psi/bar/kPa air pressure rating indicated on the tire.

WARNING! Make sure your tires are inflated to the psi/bar/kPa air pressure rating indicated on thetire for pneumatic tires. Do not underinflate or overinflate your tires. Low pressure may result inloss of control, and overinflated tires may burst. Overinflating tires can cause them to explode.

WARNING! Do not use a high pressure hose to inflate your tires.

Use a rubber conditioner on the tire sidewalls to help preserve them.

WARNING! Never use a rubber conditioner on the tread area of the tires; doing so may make thetires slippery and cause your power chair to skid.

All wheel bearings are prelubricated and sealed. They require no subsequent lubrication.




The body shroud has been sprayed with a clear sealant coating. You can apply a light coat of car wax to helpit retain its high-gloss appearance.Check all electrical connections. Make sure they are tight and are not corroded. Batteries must sit flat withinthe battery tray, with the battery terminals facing rearward. Refer to the battery wiring label for the correctwiring layout.

WARNING! Even though the power chair has passed the necessary testingrequirements for ingress of liquids, you should keep electrical connections awayfrom sources of dampness, including direct exposure to water or bodily fluids andincontinence. Check electrical components frequently for signs of corrosion andreplace as necessary.

Daily ChecksWith the controller turned off, check the joystick. Make sure it is not bent or damaged and that it returns to theneutral position when you release it. Check the rubber boot around the base of the joystick for damage. Visu-ally inspect the boot. Do not handle or try to repair it. See your Quantum Rehab Provider if there is a problem.Visually inspect the controller harness. Make sure that it is not frayed, cut, or has any wires exposed. See yourQuantum Rehab Provider if there is a problem.Check for flat spots on solid tires. Flat spots could adversely affect stability.Inspect the seating system, armrests, and front riggings for loose hardware, stress points, or damage. See yourQuantum Rehab Provider if there is a problem.

Weekly ChecksDisconnect and inspect the controller from the power base. Look for corrosion. Contact your Quantum RehabProvider if necessary.Ensure that all parts of the controller system are securely fastened to your power chair. Do not overtighten any screws.Check for proper tire inflation. Pneumatic tires should be inflated to the psi/bar/kPa air pressure rating indi-cated on each tire. If a tire does not hold air, see your Quantum Rehab Provider for replacement of the tube.Check the brakes. This test should be carried out on a level surface with at least 3 feet (1 meter) of clearancearound your power chair.

To check the brakes:1. Turn on the controller and turn down the speed level of your power chair.2. After one second, check the battery condition meter. Make sure that it remains on.3. Slowly push the joystick forward until you hear the electric brakes click. Immediately release the joystick.

You must be able to hear each electrical brake operating within a few seconds of joystick movement. Repeatthis test three times, pushing the joystick backwards, then left, and then right.

Monthly ChecksCheck for drive tire wear. See your Quantum Rehab Provider for repair.Check the caster wheels for wear. Replace them as necessary.Check the caster forks for damage or fluttering which indicates that they may need to be adjusted or have thebearings replaced. See your Quantum Rehab Provider for repair.Check the entire power chair for loose hardware and changes in the function or performance of the powerchair. See your Quantum Rehab Provider for service or repair.Keep your power chair clean and free of foreign material, such as mud, dirt, hair, food, drink, etc.Spring shocks and gas dampers should be visually checked for any abnormality, structure damage, or bentrods. See your Quantum Rehab Provider for repair.

Yearly ChecksTake your power chair to your Quantum Rehab Provider for yearly maintenance, especially if you use your powerchair on a daily basis. This helps ensure that your power chair is functioning properly and helps prevent futurecomplications.


StorageYour power chair should be stored in a dry place, free from temperature extremes. When storing, disconnect thebatteries from the power chair. See VI. “Batteries and Charging.”

WARNING! If you fail to store the unit properly, the frame can rust and the electronics can bedamaged. Any corroded electronic connection should be replaced.

Batteries that are regularly and deeply discharged, infrequently charged, stored in extreme temperatures, or storedwithout a full charge may be permanently damaged, causing unreliable performance and limited service life. It isrecommended that you charge the batteries periodically throughout periods of prolonged storage to ensure properperformance.

You may wish to place several boards under the frame of your power chair to raise it off of the ground duringperiods of prolonged storage. This takes the weight off the tires and reduces the possibility of flat spots developingon the areas of the tires contacting the ground.

Disposal of Your Power ChairYour power chair must be disposed of according to applicable local and national statutory regulations. Contactyour local waste disposal agency or Quantum Rehab Provider for information on proper disposal of power chairpackaging, metal frame components, plastic components, electronics, batteries, neoprene, silicone, andpolyurethane materials.

Cleaning and DisinfectionUse a damp cloth and mild, non-abrasive cleanser to clean the plastic and metal parts of your power chair.Avoid using products that may scratch the surface of your power chair.If necessary, clean your product with an approved disinfectant. Make sure the disinfectant is safe for use onyour product before application.

WARNING! Follow all safety instructions for the proper use of the disinfectant and/or cleaningagent before applying it to your product. Failure to comply may result in skin irritation orpremature deterioration of upholstery and/or power chair finishes.

WARNING! Never hose off your power chair or place it in direct contact with water. Your powerchair has a painted, ABS plastic body shroud that allows it to be easily wiped clean with a dampcloth.

WARNING! Never use any chemicals to clean a vinyl seat, as they may cause the seat to becomeslippery or dry out and crack. Use soapy water and dry the seat thoroughly.

Wheel ReplacementIf you have pneumatic tires and you have a flat tire, you can replace the tube. If your chair is equipped with a solidtire insert, then you must replace the entire wheel assembly. Replacement tires, tubes, and wheel assemblies arereadily available through your Quantum Rehab Provider.

WARNING! The wheels on your power chair should only be serviced or replaced by a QuantumRehab Provider or a qualified technician.

WARNING! Be sure that the controller’s power is turned off and the power chair is not infreewheel mode before performing this procedure.

WARNING! When changing a tire, remove only the five lug nuts, then remove the wheel. If anyfurther disassembly is required, deflate the tire completely or it may explode.



Figure 23. Q6 Edge HD Drive Wheel Disassembled

TIRE

SCREWSFRONT RIM HALF

LUG NUTS

REAR RIM HALF

Figure 22. Q6 Edge HD Drive Wheel

WHEEL HUB

TUBE

Follow these easy steps for a quick and safe repair for both pneumatic and solid tires:1. Turn off the power to the controller.2. Set the power chair up on blocks.3. If you are changing a pneumatic tire, completely deflate it before removing the wheel.4. Remove the (5) lug nuts from the wheel hub. See figure 22.5. Pull the wheel off of the hub.6. Remove the screws and separate the front and rear rim. See figure 23.7. Remove the old tube from the pneumatic tire and replace it with a new tube or replace the entire assembly if

it is a solid tire.8. Screw together the two rim halves.9. Slide the wheel back onto the hub.10. Reinstall the five (5) lug nuts onto the wheel hub and tighten.11. Inflate the pneumatic tire to the psi/bar/kPa air pressure rating indicated on each tire.12. Remove the power chair from the blocks.

Battery ReplacementA battery wiring diagram is printed on a decal located on the front cover. See the specification table for correctbattery specifications.


WARNING! The batteries in your power chair should only be serviced or replaced byan authorized Quantum Rehab Provider or a qualified technician.

WARNING! Do not replace batteries when seat is occupied.

WARNING! Power chair batteries are heavy. See specifications table. If you areunable to lift that much weight, be sure to get help. Use proper lifting techniques andavoid lifting beyond your capacity.

WARNING! Do not mix old and new batteries. Always replace both batteries at thesame time.

PROHIBITED! Keep tools and other metal objects away from the battery terminals.Contact with tools can cause electrical shock.



To replace the batteries:1. Turn off the power to the controller.2. Make sure that the power chair is in drive mode. See III. “Your Power Chair.”3. Remove the front cover by squeezing the release handles (see figure 24) and lifting the foot platform bracket

up and away from the power base.4. Disconnect the quick release battery connectors. See figure 6.5. Remove the batteries.6. Disconnect the battery harness from each battery.7. Connect the battery harness to the new front battery according to the battery wiring diagram. See figure 24.

WARNING! Make sure you tighten the fasteners so that the connections are secure.

8. Connect the battery harness to the new rear battery according to the battery wiring diagram. See figure 24.9. Install the new batteries and connect the quick release battery connectors.10. Reinstall the front cover and foot platform.11. Charge the batteries. See VI. “Batteries and Charging.”


REAR BATTERY

QUICK RELEASEBATTERY CONNECTORS

Figure 24. Battery Installation

BATTERY WIRING DIAGRAM LABEL

FRONT COVER

RELEASE HANDLES

FRONT BATTERY


When to See Your Quantum Rehab Provider for ServiceThe following symptoms could indicate a serious problem with your power chair. If necessary, contact yourQuantum Rehab Provider. When calling, have the model number, serial number, nature of the problem, and theerror code if available.

Motor noiseFrayed harnesses Cracked or broken connectorsUneven wear on any of the tiresJerky motionPulling to one sideBent or broken wheel assembliesDoes not power upPowers up, but does not moveLoose seat or seating components

Corrective MaintenanceIf the battery condition meter does not light up when you turn on the power:

Check the harness connections. Make sure they are tight.Check the circuit breaker. Reset it if necessary.Check the battery connections.

If the above conditions prove normal, you can load test the batteries with a battery load tester. These testers areavailable at automotive parts stores. Disconnect both batteries before load testing and follow the directions thatcome with the load tester. If either one of the batteries fails the load test, replace both of them. If your power chairstill does not power up, contact your Quantum Rehab Provider.



N O T E S

WARNING! A Quantum Rehab Provider or a qualified technician must perform the initial setup ofthis power chair and must perform all of the procedures in this manual.

The symbols below are used throughout this owner’s manual and on the power chair to identify warnings andimportant information. It is very important for you to read them and understand them completely.

WARNING! Indicates a potentially hazardous condition/situation. Failure to follow designatedprocedures can cause either personal injury, component damage, or malfunction. On theproduct, this icon is represented as a black symbol on a yellow triangle with a black border.

MANDATORY! These actions should be performed as specified. Failure to perform mandatoryactions can cause personal injury and/or equipment damage. On the product, this icon isrepresented as a white symbol on a blue dot with a white border.

PROHIBITED! These actions are prohibited. These actions should not be performed at any timeor in any circumstances. Performing a prohibited action can cause personal injury and/orequipment damage. On the product, this icon is represented as a black symbol with a red circleand red slash.

INTENDED USEThe intended use of the Pride Mobility Products device is to provide mobility to persons limited to a seatedposition that have the capability of operating a powered wheelchair.

Quick Reference Information

S A F E T Y G U I D E L I N E S

Copyright © 2012Pride Mobility Products Corp.INFMANU4237/Rev A/April 2012

Quantum Rehab Provider:

Address:

Phone Number:

Purchase Date:

NOTE: This owner’s manual is compiled from the latest specifications and product information available atthe time of publication. We reserve the right to make changes as they become necessary. Any changes to ourproducts may cause slight variations between the illustrations and explanations in this manual and the productyou have purchased. The latest/current version of this manual is available on our website.

QUANTUM

Pride keeps a more detailed report on file at the factory.

Date Inspected

Inspector

Inclusion of all Parts

Joystick Serial Number

Controller Serial Number

Left Motor Serial Number

Right Motor Serial Number

Fit and Finish

Performance

*INFMANU4237* Product Serial #

Q6 Edge HD

Quality Control – Q6 Edge HD

quality control – q6 edge hd quantumq6 edge hd quality control – q6 edge hd. warning! a quantum...

Documents