protector sz

8/10/2019 Protector SZ

1/15

Telecom Surge Protectors

* All specs and applications shown above subject to change without prior notice.S&T INDUSTRIAL PARK, BUILDING D, NO.57, HUOJU RD.,SUZHOU NEW DISTRICT, JIANGSU, CHINA e-mail: [email protected]

Tel :86-512-68410367 http://www.ceramate-thyristor.comFax:86-512-68410467 Page 1 of 15 Rev 1.0 Jun. 2013

DescriptionThese devices are designed to limit

overvoltages for the common telecommunicationline of communication, computer and consumerproducts. Overvoltages are normally caused by a.c.power system or lightning flash disturbances whichare induced or conducted on to the commonproducts. A single device provides 2-pointprotection and is typically used for the protection of2-wire telecommunication equipment (e.g.between the Ring and Tip wires for telephones andmodems). Combinations of devices can be used

for multi-point protection (e.g. 3-point protectionbetween Ring, Tip and Ground).

The protector consists of a symmetricalvoltage-triggered bi-directional sidac. Overvoltagesare initially clipped by breakdown clamping untilthe voltage rises to the breakover level, whichcauses the devices to crowbar into a low-voltageon state. This low-voltage on state causes thecurrent resulting from the overvoltage to be safelydiverted through the device. The high crowbar

holding current prevents d.c. latchup as thediverted current subsides. These protectors areguaranteed to voltage limit and withstand the listedlightning surges in both polarities.

Advantages The advantages of using this device over other surge suppression devices is that the

device offers absolute surge protection regardless of the surge current available and therate of applied voltage (dV/dt). Unlike other devices, the device: Can not be damaged by voltage Eliminates hysteresis and heat dissipation typically found with a clamping device Eliminates voltage overshoot caused by fast rising transients Is non-degenerative Will not fatigue Has negligible capacitance making it ideal for high speed transmission equipment

CA SeriesSMA

CB SeriesSMB

CD SeriesTO-92

CE SeriesDO-15DO-27


2/15




Appl ications Customer Premises Equipment (CPE) such as phone, modems and caller ID

adjunct boxes T-1/E-1, ISDN and xDSL transmission equipment Data lines and security systems Primary protection including main distribution frames, building entrance equipment

and station protection modules

Terms and Symbols

Item Symbol Test Condition

Peak Off-stateVoltage VDRM

Maximum voltage that can be applied whilemaintaining off-state.

Leakage Current I DRM Maximum peak off-state current measured atVDRM .

Breakover Voltage V S Maximum voltage prior to breakover to onstate. It is measured at 100V/ms.

Peak Pulse Current I PP

Rated peak pulse current of specifiedamplitude and waveshape that may be appliedwithout damage.

Apply the impulse 10160s or 101000scurrent waveform for 3 times with intervals of30 seconds.

On-state Voltage V T Maximum voltage across the device in theon-state condition at a specified on-statecurrent (I T).

On-state Current I T Maximum rated continuous on-state current.

Breakover Current I S Maximum current required to breakover to

on-state.

Holding Current I H Minimum current required to maintain thedevice in the on-state condition.

Off-stateCapacitance CO

Typical capacitance measured in off-state.It is measured at 1MHz with a 2V bias.


3/15




Electrical Characteristics (25C unless otherwise noted)

CA SERIESPart No.

Note 1

Marking

Note 1

VDRM (V)

MAX

Vs(V)

MAX

IDRM ( A)

MAX

@ VDRM

VT (V)

MAX@ I T

Is(mA)

MAX

IT (A)

IH (mA)

MIN

Co(pF)

TypicalNote 2

C0080A C-8 6 25 60

C0300A C03 25 4050

60

C0640A C06 58 77 60

C0720A C07 65 88 60

C0900A C09 75 98 60

C1100A C11 90 130 60

C1300A C13 120 160 60

C1500A C15 140 180 45

C1800A C18 170 220 45

C2300A C23 190 260 45

C2600A C26 220 300 30

C3100A C31 275 350 30

C3500A C35 320 400 30

C4000A C40 350 460

5 5 800 1

130

30

Note 1: For individual AA and AB surge ratings, see table below.Note 2: Co is a typical value for AA product. AB capacitance is approximately

1.5x the listed value.Note 3: Storage and operating junction temperature -40 to 150C.

Surge Rating(Ipp)

2 X 10 s

(A)

8 X 20 s

(A)

10 X 160 s

(A)

10 X 560 s

(A)

10 X 1000 s

(A)

A 150 150 90 50 50

B 250 250 150 100 80


4/15




CB SERIES

Co

(pF)Typical

Part No.

Note 1

Marking

Note 1

VDRM

(V)

MAX

Vs(V)

MAX

IDRM

( A)

MAX@ VDRM

VT

(V)

MAX@ I T

Is(mA)

MAX

IT

(A)IH

(mA)

MIN

note 2 BCC BD

C0080B C-8 6 25 60 60 160C0300B C03 25 40

5060 60 160

C0640B C06 58 77 60 60 160

C0720B C07 65 88 60 60 160

C0900B C09 75 98 60 60 160

C1100B C11 90 130 60 50 160

C1300B C13 120 160 60 50 160

C1500B C15 140 180 45 50 160C1800B C18 170 220 45 40 160C2300B C23 190 260 45 40 120

C2600B C26 220 300 30 40 120C3100B C31 275 350 30 40 120C3500B C35 320 400 30 40 120C4000B C40 350 460

5 5 800 1130

30 40 150

Note 1: For individual BA, BB and BC surge ratings, see table below.Note 2: Co is a typical value for BA product. BB capacitance is approximately 1.5x the listed

value, BC capacitance is approximately 2.5x the listed value.

Note 3: Storage and operating junction temperature -40 to 150C.

Surge Rating (Ipp)

2 X 10 s

(A)

8 X 20 s

(A)

10 X 160 s

(A)

10 X 560 s

(A)

10 X 1000 s

(A)

A 150 150 90 50 50

B 250 250 150 100 80

C 500 400 200 150 100

CC 500 400 200 150 100D 1000 800 400 300 200


5/15




CD SERIES

MarkingPart No.

Note 1 Note 1 or

VDRM

(V)

MAX

Vs

(V)

MAX

IDRM ( A)

MAX@ VDRM

VT (V)

MAX@ I T

Is

(mA)

MAX

IT

(A)

IH

(mA)

MIN

Co(pF)

TypicalNote 2

C0080D C-8 C0080D50/75/100 6 25 60

C0300D C03 C0300D50/75/100 25 4050

60

C0640D C06 C0640D50/75/100 58 77 60

C0720D C07 C0720D50/75/100 65 88 60

C0900D C09 C0900D50/75/100 75 98 60

C1100D C11 C1100D50/75/100 90 130 60

C1300D C13 C1300D50/75/100 120 160 60

C1500D C15 C1500D50/75/100 140 180 45

C1800D C18 C1800D50/75/100 170 220 45

C2300D C23 C2300D50/75/100 190 260 45

C2600D C26 C2600D50/75/100 220 300 30

C3100D C31 C3100D50/75/100 275 350 30

C3500D C35 C3500D50/75/100 320 400 30

C4000D C35 C40000D50/75/100 350 460

5 5 800 1

130

30

Note 1: For individual DA, DB and DC surge ratings, see table below.Note 2: Co is a typical value for DA product. DB capacitance is approximately 1.5x the listed

value,DC capacitance is approximately 2.5x the listed value. Note 3: Storage and operating junction temperature -40 to 150C.

Surge Rating (Ipp)

2 X 10 s

(A)

8 X 20 s

(A)

10 X 160 s

(A)

10 X 560 s

(A)

10 X 1000 s

(A)

A 150 150 90 50 50

B 250 250 150 100 80

C 500 400 200 150 100


6/15




CE SERIES

Part No.

Note 1

Marking

Note 1

VDRM (V)

MAX

Vs(V)

MAX

IDRM

( A)MAX

@ VDRM

VT

(V)MAX@ I T

Is(mA)

MAX

IT (A)

IH (mA)

MIN

Co

(pF)TypicalNote 2

C0080E C-8 6 25 60

C0300E C03 25 4050

60

C0640E C06 58 77 60

C0720E C07 65 88 60

C0900E C09 75 98 60

C1100E C11 90 130 60

C1300E C13 120 160 60

C1500E C15 140 180 45

C1800E C18 170 220 45

C2300E C23 190 260 45

C2600E C26 220 300 30

C3100E C31 275 350 30

C3500E C35 320 400 30

C4000E C40 350 460

5 5 800 1

130

30

Note 1: For individual EA, EB and EC surge ratings, see table below.Note 2: Co is a typical value for EA product. EB capacitance is approximately

1.5x the listed value,EC capacitance is approximately 2.5x the listed alue. Note 3: Storage and operating junction temperature -40 to 150C.

Surge Rating (Ipp)

PACKAGE2 X 10 s

(A)

8 X 20 s

(A)

10 X 160 s

(A)

10 X 560 s

(A)

10 X 1000 s

(A)

A DO-15 150 150 90 50 50

B DO-15 250 250 150 100 80C DO-27 500 400 200 150 100


7/15





8/15




Part Number Information

C 310 0 * * *

Device TypeMedianVoltageRating

ConstructionVariable

Package TypeIpp Rating10 X 1000 s

Options

C: Protector 310=310V 0: One chip

A: SMAB: SMB

D: TO-92

E: DO-15/DO-27

A=50AB=80A

C=100A

D=200A

C:Low

Capacitance


9/15




Package Dimensions

CA SeriesInches Millimeters

Dimension Min Max Min Max

A 0.090 0.118 2.29 3.00

B 0.177 0.213 4.50 5.40

C 0.050 0.065 1.25 1.65

D 0.154 0.183 3.90 4.65

E 0.030 0.060 0.76 1.52

F 0.006 0.012 0.15 0.30

G 0.008 0.20

H 0.080 0.096 2.03 2.44

SMA

CB SeriesInches Millimeters

Dimension Min Max Min Max

A 0.122 0.159 3.10 4.04

B 0.196 0.224 4.98 5.70

C 0.075 0.087 1.90 2.20

D 0.156 0.193 3.96 4.90

E 0.030 0.060 0.76 1.52

F 0.006 0.012 0.15 0.30

G 0.008 0.20

H 0.075 0.102 1.90 2.60

SMB


10/15




CD Series

Inches MillimetersDimension

Min Max Min Max

A 0.173 0.197 4.4 5.0

B 0.500 12.7

D 0.095 0.105 2.41 2.67

E 0.150 3.81

F 0.046 0.054 1.16 1.37

G 0.135 0.145 3.43 3.68

H 0.088 0.098 2.23 2.50

J 0.176 0.186 4.47 4.73K 0.088 0.096 2.23 2.44

L 0.012 0.035 0.30 0.90

M 0.012 0.018 0.3 0.45

TO-92

N 0.063 1.6

CE Series

Dimension Inches MillimetersPackage symbol Min Max Min Max

A 1.000 25.4

B 0.220 0.300 5.6 7.6

C 0.028 0.035 0.7 0.9DO-15

D 0.100 0.150 2.6 3.8

A 1.0 25.4

B 0.33 0.38 8.5 9.5

C 0.048 0.056 1.2 1.4

DO-15, DO-27

DO-27

D 0.197 0.220 5.0 5.6


11/15




Packing

BULK PACKINGPACKAGE INNER SIZE

(mm)

BOX

(EA)

CARTON SIZE

(mm)

CARTON

(EA)

TO-92 168x73x123 3000 355x265x165 24000

DO-15 192x85x21 500 475x225x260 25000

DO-27 192x85x21 250 475x225x260 12500

REEL PACKINGPACKAGE REEL

(EA)

COMPONENT

SPACE

(mm)

TAPE

SPACE

(mm)

REEL

DIA

.(mm)

CARTON

SIZE

(EA)

CARTON

(EA)

DO-15 4000 5.0 52 330 355x355x355 16000

DO-27 1250 10.0 52 330 355x355x355 5000

SMA 6000/1500 4.0 330/178 355x355x355 96000

SMB 3000/750 4.0 330/178 355x355x355 48000

AMMO PACKINGPACKAGE AMMO

(EA)

BOX SIZE

(mm)

CARTON SIZE

(mm)

CARTON

(EA)

TO-92 2000 327x41x182 500x400x230 20000


12/15




Taping Specifications For Axial Lead

Axial lead devices are packed in accordance with EIA standard RS-296-E and specifications given below

COMPONENT PITCH A INNER TAPE PITCH BCOMPONENTOUTLINE 0.5 mm 1.5 mm

CUMULATIVE PITCHTOLERANCE

DO-15 5.0 mm 52.0 mm 2.0mm/20 pitch

DO-27 10.0 mm 52.0 mm 2.0mm/10 pitch

ITEM SYMBOL SPECIFICATIONS

(mm)

SPECIFICATIONS

(inch)

Component alignment Z 1.2 max. 0.048 max.

Tape width T 6.0 0.4 0.2360.016

Exposed adhesive E 0.8 max. 0.032 max.

Body eccentricity | L1-L2 | 1.0 max. 0.040 max.

Reel outside diameter D 330.0 13.0

Reel inner diameter D1 85.7 0.3 3.375 0.197

Feed hole diameter D0 16.6 1.0 0.655 0.040

Reel width W 79.0 1.0 3.110 0.040

Notes : Each component lead shall be sandwiched between tapes for a minimum of 3.2mm(0.126)


13/15




Taping Specifications For Surface Mount Devices

Product CA(SMA) CB(SMB)Symbol mm inch mm inch

A0 2.72 0.10 0.109 0.004 3.79 0.15 0.149 0.006B0 5.25 0.10 0.210 0.004 5.72 0.15 0.225 0.006d 1.55 0.05 0.061 0.002 1.55 0.05 0.061 0.002D 330.0/178.0 13.0 / 7.0 330.0/178.0 13.0 / 7.0

D1 50.0 min. 1.969 min. 50.0 min. 1.969 min.D2 13.50 1.0 0.531 0.039 13.50 1.0 0.531 0.039E 1.75 0.10 0.069 0.004 1.75 0.10 0.069 0.004

F 5.50 0.05 0.217 0.002 5.50 0.05 0.217 0.002K0 2.66 max 0.105 max 3.0 max 0.118 maxP 4.00 0.10 0.157 0.004 8.00 0.10 0.315 0.004

P0 4.00 0.10 0.157 0.004 4.00 0.10 0.157 0.004P1 2.00 0.05 0.079 0.002 2.00 0.05 0.079 0.002

t 0.60 max 0.024 max 0.60 max 0.024 maxW 12.00 0.30 0.472 0.012 12.00 0.30 0.472 0.012

W1 18.4 max 0.724 max 18.4 max 0.724 maxNotes: 1. There shall be leader of 230 mm minimum which may consist of carrier and or cover

tape follower by a minimum of 160 mm of carrier tape sealed with cover tape.

2. There shall be a minimum of 160mm of empty component pockets sealed with covertape.


14/15


15/15



Ammo

protector sz

Documents