project report of audio amplifier with woofer and tweeter
TRANSCRIPT
-
7/27/2019 project report of audio amplifier with woofer and tweeter
1/7
AUDIO AMPLIFIER WITHWOOFER AND TWEETTER
-
7/27/2019 project report of audio amplifier with woofer and tweeter
2/7
2
I N D E X
Sr no. Title Page No.
1 Project description 4
2 Circuit diagram 5
3 Component list 6
4 Working 6
5 Application 8
6 Conclusion 8
7 References 8
8 Datasheet 9
-
7/27/2019 project report of audio amplifier with woofer and tweeter
3/7
3
PROJECT DESCRIPTION
It is a Audio amplifier project. First of all, what is audio amplifier? An audio amplifieris an electronic amplifier that amplifies low power audio signal to a level suitable for
driving loudspeakers. The input signal of an audio amplifier may only a few mill
watts, but its output may be tens or even thousands of watts.
Design parameters
Gain Frequency response Distortion Noise
These are interdependent, increasing gain often leads to undesirable increases in
noise and distortion. While negative feedback actually reduces the gain, it also
reduces distortion. Since modern digital devices already provide a flat signal at
line level, the preamplifier is not needed other than as a volume control.
In this project we are making simple audio amplifier with woofer and tweeter. We
have two controls of woofer sound intensity and tweeter sound intensity.
WOOFER:A woofer is a driver that reproduces low frequencies.
TWEETER: A tweeter is a high frequency driver that reproduce the highest
frequencies in a speaker system.
-
7/27/2019 project report of audio amplifier with woofer and tweeter
4/7
4
CIRCUIT DIAGRAM
-
7/27/2019 project report of audio amplifier with woofer and tweeter
5/7
5
COMPONENT LIST
Resistors Capacitors TDA 2005s dual audio amplifier IC Loudspeakers
WORKING
There are two main part of the circuit.
(1)Filter
(2)Amplifier
There are two filter low pass and high pass. Low pass filter is used for woofer.
High pass filter is used for tweeter. Woofer mainly used for speech signal and
tweeter is used for other music frequency. We set the value of resister and capacitor
so it acts as low or high pass filter.
Low pass filter:
R = 1K
C = 56nF
fl =
= 2842.05 Hz
-
7/27/2019 project report of audio amplifier with woofer and tweeter
6/7
6
Generally the speech signal is only in the range 30Hz to 3000Hz. So we
design low pass filter for that range and that filtered signal is amplified
and given to the woofer.
High pass filter:
R = 1K
C = 56nF
fl =
=2842.05
Generally the music signal is in the range above 3000Hz. So we design
high pass filter for that range and that filtered signal is amplified andgiven to the tweeter.
There are two variable resistor using which we can control the gain of the
amplifier. So the intensity of the sound varies with change in resistance values.
In this project we use TDA 2005s IC that is class B dual audio power amplifier withthermal shut down capability. Power booster amplifiers are easily designed using this
device that provides a high current capability up to 3.5 A. so in our project it will
amplify our audio signal. That output signal is control by R3 and R5 resistor which
are variable in nature.c7, c8 and c9 capacitors are used to control noise .Then it
connected to loudspeaker.
-
7/27/2019 project report of audio amplifier with woofer and tweeter
7/7
7
APPLICATIONS
In portable home theatre system In car radio application In public address system
CONCLUSION
Using TDA 2005s IC we amplify low level audio signals (in mille watts) to high level
audio signals (in watts).we give two inputs to the audio amplifier of high and low cutoff using high and low pass filter. And we able to make a circuit which can work on
12 volt d.c supply.
REFERENCE www.google.com www.alldatasheet.com