PROGARD® PACKCat. # PROGOTOS2 - PR0G0TNP2

Replacement

Where used • Milli-Q® Integral systems• Elix® and Elix Advantage systems• All Essential range

Shipping boxc o n t e n t

1 Progard Pack

W h e n t o F o r I n t e g r a l r a n g e :

replace theProgard Pack? The Progard pack should be replaced when one of the following Alert messages

is displayed:• REPLACE PROGARD AND TANK VENT FILTER IN XX DAYS, or

• REPLACE PROGARD AND TANK VENT FILTER.

For Essential range:

• When the system displays the yellow alert:

H o w t o

proceedFor the Integral range, the procedure is described below.For the Essential range, the User Manual describes this procedure.

The information in this document is meant to be used by a Qualified Service RepresentativeP F 0 9 7 6 1 - R e v . 3 , 1 2 / 2 0 1 3 P R O G A R D ® P A C K 1 / 5

Procedure

Removal Follow the steps below to remove the Progard pack.

Step A c t i o n Diagram1 Place the Milli-Q System into

STANDBY Mode.

S T A N D B Y

10 Sep 2007 14:12

Readij •*

2 Depressurize the system:• Push the Q-POD plunger all the way down and release it.• Walt until water stops flowing.• Push the Q-POD plunger all the way down and release it.

3 • Open the Milli-Q System leftd o o r .

• Lift up the pack lockingh a n d l e .

4 Remove the used Progard pack. 1

J ."yn^T'

i ' ,

5 The system indicates that theProgard pack is removed.

S T fl l

P R O G A R D PA C K

O U T

= R E S S +

1 U

Continued on next page

THE [NFORMATION IN THIS DOCUMENT IS MEANT TO BE USED BY A QUALIFIED SERVICE REPRESENTATIVEP F 0 9 7 6 1 - R e v . 3 , 1 2 / 2 0 1 3 p r o g a r d ® P A C K 2 / 5

Procedure, Continued

Installation Follow the steps below to install the Progard pack.• Remove the covers on the 2 ports of the Progard pack.• Make sure the rubber 0-rings are firmly in place inside these ports.• Wet the 0-rings with water.

Step A c t i o n

Lift the pack locking handleup.Push the top of the Progardpack into the ports on the

li-Q system.

Diagram

Push on the bottom of the

Progard pack.

Continued on next page

T h e i n f o r m a t i o n i n t h i s d o c u m e n t i s m e a n t t o b e u s e d b y a Q u a l i fi e d S e r v i c e R e p r e s e n t a t i v eP F 0 9 7 6 1 - R e v . 3 , 1 2 / 2 0 1 3 P R 0 G A R D ® P A C K 3 / 5

Procedure, Continued

I n s t a l l a t i o n

(continued] Step A c t i o n Diagram

3 • Push the pack locking handled o w n .

• Close the left door.

A i

4 The system indicates that a newProgard is installed.

I N S TA L L P R O G A R D

A fieu PT093rd has beeni n s t a l l e d .

Catalogue N": PR0G0T002Lot N': FSDN27324.Press •> to start Progard

Flushing.

5 Press C) to start the Progardfl u s h .

I N S TA L L P R O G A R D

Progard Flush procedure inprogress .Renaining Tine • 15 nin.P r e s s ■» t o c a n c e l .

6 When the Progard Pack flushhas finished, the Milli-Q Systemgoes to READY Mode.

R E A D Y

10 Sep 2007 14:22

s m c s cstandby ->

E l l x R : 1 2 . 5 M a c m T C

El ix T : 25.1 "C

Ta n k : 8 0 . 0 %

Continued on next page

The INFORMATION IN THIS DOCUMENT IS MEANT TO BE USED BY A QUALIFIED SERVICE REPRESENTATIVEP F 0 9 7 6 1 - R e v . 3 , 1 2 / 2 0 1 3 p r o g a r d ® p a c k 4 / 5

Procedure, Continued

I n s t a l l a t i o n

(continued) Step A c t i o n Diagram

7 Unscrew and replace the ventfi l t e r .

T h e i n f o r m a t i o n i n t h i s d o c u m e n t i s m e a n t t o b e u s e d b y a Q u a l i fi e d S e r v i c e R e p r e s e n t a t i v eP F 0 9 7 6 1 - R e v . 3 , 1 2 / 2 0 1 3 p r o g a r d ® p a c k 5 / 5