product overview - vanduongong.com · product overview. sensors ... sti series. motorised control...
TRANSCRIPT
Product Overview
SENSORS• Resistance thermometer • Pressure gauges • Level transducers • Power supply unit
Resistance thermometer for precise temperature measurement and controlSeries WT 1000
• Resistor elements in accordance with DIN 43760 IEC 571• Measuring resistor PT 100• Fast response time• Easy to install• No calibration necessary
Series Specification Data Sheet
WT 1000 Resistance thermometer 1100-7010
Electronic pressure gauge station for use in refrigeration and heating application - measuring pressure in system operating with gases and liquids Series DR 1226
• Piezoresistive• Measuring range up to 60 barg• Output 4 - 20 mA• Power supply 24 V DC (auxiliary supply needed)• with pressure gauge & gauge cock• Two-wire system
Series Specification Data Sheet
DR 1226 Electronic pressure gauge station 1226-7010
Digital level transducer for vessels, especially for condensate, steam & hot water boilers and refrigerants up to PN 100.Series NI 1331 / 1332
• Linear measuring range 150 - 4000 mm• Wear-resistant, inductive measurement• Output 4 – 20 mA• measuring range digitally adjustable• LED display at every 10% steps• No connection between displacer and electronic
Series Specification Data Sheet
NI 1331/1332 Digital level transducer 1331-7010
Electronic Controllers
• Process controller • Switch gears
Process controller Electronic 3-term step-controllers with PI-control
• Drive for electric actuators• Set point selection by manual controller or programme
tuner• Function points for limit monitor and measuring
transducer• Disturbance variables and auxiliary three element
control• Manual and automatic operation
Digital controller with PID control RE3x52 freely configurable as:
• 3-term-step-controller for driving electric actuators e.g. RTK actuators ST 5100 series or
• Continuous controller for driving pneumatic actuators with positioner e.g.: RTK SR 6136 , SR 6137 series
Series Specification Data Sheet
RE 3304 Analog controller 3304-7010
RE 3052/ RE 3053 Digital controller 3050-7010
RE 3070 Digital controller 3070-7010
Switch gears Electronic switchgear
• DIN rail installation• 2 separate channels• 1 change-over contact per channel• Delay adjustable• LED switching display• Current and voltage input
Series Specification Data Sheet
SG 2431 Electronic switchgear 2431-7010
Control valves• Electric and pneumatic control valves (heat control) • Electric and pneumatic control valves (refrigeration
control)• Control valve in three-way design • Motorised valve with emergency closing device • Steam converting valve • Control valve for water injection • Feed-water control valve with spill back • Continuous blowdown valve • Bottom blowdown valves • Blowdown valves • Control valves for regulating flow/circulation • Pressure-balanced Shut-off and control valves
Model codeM V 5 2 1 1Actuator Actuating force Valve type Spindle packing
5: electric (MV)
2: 3 kN 3: 6 - 10 kN 4: 10 - 56 kN 9: > 56 kN
1: two-way 2: three-way
1: Stuffing box 4: bellows seal with safety stuffing box
PV 6 2 1 1Actuator Diaphragm area Valve type Spindle packing
6: pneumatic (PV)
2: 120 cm² 2: 280 cm² 3: 530 cm² 3: 1000 cm²
1: Valve type 2: 3-Way
1: Stuffing box 2: bellows seal with safety stuffing box
Electric and pneumatic control valves (heating application )Motorised control valves for throttling, mixing and diverting of liquids and gases
• Two-way and three-way design• Optimum control with adjustable cone assemblies• Various cone designs• Body material made of GG 25, GGG 40.3, GS-C 25, 1.4408• ANSI - Control valves in 2-way design, Material A216 WCB 1“,1½ “, 2 “, 2 ½ “, 3“,
4“, 6“ , Class 150 and class 300 for electric and pneumatic actuators.
Series Actuating force Spindle Two-way Three-way Actuators
MV 5200 3 kN 12 mm MV 5210 MV 5220 ST 5112 (3 kN)
MV 5300 6 - 10 kN 12 mm MV 5310 MV 5320
ST 5113 (6 kN) ST 5114 (10 kN) AUMA series
MV 5400
10 - 56 kN
32 mm MV 5410 MV 5420 ST 5115 (10 kN) ST 5106 (15 kN) AUMA series
* For valves with spindle packing bellows seal, the last figure is a 4 instead of the 1.
PN 40 with spindle packing bellows seal on demand.
Series Actuating force Spindle Two-way Three-way Actuators
PV 6200
120 cm² 280 cm² 12 mm PV 6210 PV 6220 ST 6116
ST 6121PV 6300 530 cm² 12 mm PV 6310 PV 6320 ST 6131
PV 6400
1000 cm² 32 mm PV 6410 PV 6420 ST 6141 STI series
Electric & pneumatic control valves (refrigeration application) Motorised control valves for throttling, mixing and diverting of liquids and gases
• Two-way and three-way design• Optimum control by adjusted cone assemblies• Various cone designs• Body material made of GG 25, GGG 40.3, GS-C 25, 1.4408
Series Actuating force Spindle Two-way Three-way Actuators
MV 5200K 3 kN 12 mm MV 5210 MV 5220 ST 5112 (3 kN)
MV 5300K 6 - 10 kN 12 mm MV 5310 MV 5320
ST 5113 (6 kN) ST 5114 (10 kN) AUMA series
MV 5400K
10 - 56 kN
32 mm MV 5410 MV 5420 ST 5115 (10 kN) ST 5106 (15 kN) AUMA series
* For valves with spindle packing bellows seal, the last figure is a 4 instead of the 1.
PN 40 with spindle packing bellows seal on demand.
Series Actuating force Spindle Two-way Three-way Actuators
PV 6200K
120 cm² 280 cm² 12 mm PV 6210 PV 6220 ST 6116
ST 6121PV 6300K 530 cm² 12 mm PV 6310 PV 6320 ST 6131
PV 6400K
1000 cm² 32 mm PV 6410 PV 6420 ST 6141 STI series
Motorised control valves for mixing and distribution of thermal oil and liquids and gases Series MV 5270 / PV 6270, MV 5200/PV 6200, MV 5300/PV 6300, MV 5400/PV 6400
• Nominal diameter DN 20...300• Three-way design• Three-way design with short B-flange• Spindle packing with chevron rings or maintenance-free bellow
seal with safety stuffing box design• Easy to change actuator orientation for operation and cabling
access• Optimum control with adjusted cone assemblies• Various cone designs• ANSI - Control valves in 3-way design
Series Specification Data Sheet
MV 5270/ PV 6270
Control valve in three-way design with electric or pneumatic actuator
5270-7010
MV 5200/ PV 6200
Control valve in two-way or three-way design with electric or pneumatic actuator
5200-7010
ANSI_5200-7010
MV 5300/ PV 6300
Control valve in two-way or three-way design with electric or pneumatic actuator
5300-7010
ANSI_5300-7010
MV 5400/ PV 6400
Control valve in two-way or three-way design with electric or pneumatic actuator
5400-7010
ANSI_5400-7010
Emergency closing for Motorised valves MV 53.. / MV 54.. / MV 59.. series two-way or three way design Series ST 6150
• approved by German Technical Inspectorate (TÜV) as a motorised actuator with fail close safety function in heating systems - suitable for liquid or gases.
• closes at power failure or emergency• closes smoothly even at large differential pressures• adjustable closing time for ST 6152• automatic reset to normal operation upon power
resumption.
Series Specification Data Sheet
ST 6150/ ST 6151/ ST 6152 Motorised valve with emergency closing 6150-7010
Steam-converting valves - combined pressure reducing and desuperheating of superheated steam. Series MV 5051 / PV 6051
• Steam pressure reduction and cooling in one unit• Low-noise perforated cone• Integral cooling water injection from below• Wide control range
Series Specification Data Sheet
MV 5051/ PV 6051 Steam-converting valves 5702-7010
Electric and pneumatic control valves for cooling water injection to steam-converting valves or liquids with high differential pressureSeries MV 5211
• Nominal diameter DN 15...50• Nominal pressure PN 16...160• Ferro-titanium trims.• Optimum control with adjusted cone assemblies for low flowrates.• Body material made of GS-C 25, GS 17, CrMo 55, stainless steel
Series Specification Data Sheet
MV 5211 Water injection valve for steam converting 5703-7010
Control valve for boiler feed-water control systems on steam boilers Series MV 5291 / MV 5391
• maintain minimum flow rate for boiler-feed pump during valve close.• adjustable recirculation flow rate• perforated cone for feed-water control• Suitable for boiler steam capacity 5...50 t/h• nominal size DN 25..DN 50, DN 80• nominal pressure PN 40
Series Specification Data Sheet
MV 5291/ MV 5391 Feed-water control valves with spill back 5704-7010
Motorised control valves for continuous blowdown systems of steam boilers.Series MV 5291
• Nominal diameter DN 15...25• nominal pressure PN 40• Two-way design with / without sample valve• Hardened cone and seat for longer life span• body material made of GS-C 25• Parabolic cone with linear characteristic for exact dosing of
blowdown flowrate
Series Specification Data Sheet
MV 5291 Continuous blowdown valve 5706-7010
Bottom blowdown valve for boilersSeries HV 6291 / PV 6291
• Nominal diameter DN 20...65• nominal pressure PN 40• maintenance free spindle packing• clear flow through valve• protection of spindle packing by back sealing• easy replacement of cone
Series Specification Data Sheet
HV 6291/ PV 6291 Bottom blowdown valves 6702-7010
Blowdown valve Series KV / HV 6595
• Nominal diameter DN 25-50• Nominal pressure PN 40• No stuffing box - no leakage of medium• No compressed air connection necessary• Absolute impermeability towards the outside• Adjustable opening and closing times• No wearing parts
Series Specification Data Sheet
KV / HV 6595 Blowdown valve 6703-7010
Control valves for regulating flow/circulationSeries MV 52-/5341 / PV 62-/6341
• Nominal width DN 50 ... 150• Nominal pressure PN 16 ... 40• Three-way design• Kvs value adjustable at port B• Cone can be rotated 80°• Vacuum-resistant on circulation side• Circulation cone assembly adapted for cavitation• Valve housing made from GJS-400-18-LT, GP-240 GH,
1.4408
Series Specification Data Sheet
MV 5241/ MV 5341 PV 6241/ PV 6341 Control valves for regulating flow/circulation 5741-7010
Pressure-balanced Shut-off and control valvesSeries MV 5311, MV 5411 / PV 6311, PV 6411
• Nominal diameter DN 100...400 NPS 4"...6"• Nominal pressure PN 16 ... 160, #150...#300• Two-Way• Valve body materials JS-1025 (GJS-400-18LT), 1.0619
(GP-240-GH), 1.4408 (GX-5CrNiMo 19-11-2-), 1.7357 (G17CrMo5-5), A 216 WCB
Series Specification Data Sheet
MV 5311 / PV 6311 Pressure-balanced Shut-off and control valves 5300-7110
MV 5411 / PV 6411 Pressure-balanced Shut-off and control valves 5400-7110
Actuators• Electric actuators • Options for electric actuators • Pneumatic actuators • Options for pneumatic actuators
Electric actuatorsElectric actuator for modulating control and on/off valves
• operating by 3-term-step controllers or analogue signals 0/4..20 mA, 0..10 V DC or field bus
• separate torque switch and limit switch for both directions• protection rating IP 65• valve position indicator• manual hand wheel• optional accessories available• self locking and stall-proof stop-motor
Actuating force Actuator Switching
mode Stroke Model
3 kN ST 5112 torque (limit)
All electric actuators 40mm MV 5200
6 kN ST 5113 Limit (stall proof)
are also alternatively 60mm MV 5300
10 kN ST 5114 torque (limit)
DAC*(Digital Actuator)
80mm MV 5300
15 kN ST 5106 Limit 85mm MV 5400
Electric heavy duty actuatorsBrands like AUMA, EMG, Schiebel, Schoppe & Faeser, SIPOS, etc.available Actuating force up to 80 kN ( higher forces on demand.)Series Specification Data Sheet
ST 5112 Electric actuator 3 kN 5112-7010
ST 5113 Electric actuator 6 kN 5113-7010
ST 5114 Electric actuator 10 kN 5114-7010
ST 5106 Electric actuator 15 kN 5106-7010
ST 5116 Electric actuator 20 kN 5116-7010
ST 5143 Rotary actuator 5143-7010
Options for Electric actuatorsAdditional equipment for actuator types ST 5112, ST 5113, ST 5114, ST 5106
Series Specification Data Sheet
RE 3447 Digital Valve positioner 3447-7330
RE 3581 Digital actuator control 3581-7350
MU 4522/ MU 4524 Transducer 4520-7410
BS 4581 Profibus
4581-7360
GSD-File
BS 4591 CAN OPEN 4591-7360
MU 4586 Double rotation angle transducer contactless 4586-7410
Potentiometer 5100-7510
LB 6150 Logic PCB 6150-7110
Pneumatic actuatorsPneumatic actuators for modulating control and on/off valves
• Reversible direction of action• Stroke Min. 20 mm / Max. 80 mm• Max. air pressure 6 barg• actuating force Min 9 kN / Max 18 kN (ST 6121 / ST 6122)• approved by German Technical Inspectorate (TÜV) as an
actuator for water and steam with safety function in heating systems
Diaphragm area Actuator Spring
range Stroke valve series
120 cm² ST 6115.A6.-3S 0,9..2,0 bar 20 mm PV 6200
280 cm²
ST 6135.B6-2G ST 6135.B6-6G
0,2..1 bar 0,8..3 bar
35 mm
35 mmPV 6200
530 cm² 530 cm² 530 cm²
ST 6160.A6-6G ST 6160.C6-3G ST 6160.C6-7G
0,8..2,8 bar 0,3..1,3 bar 0,6..3 bar
40 mm
60 mm
60 mm
PV 6300
1000 cm² ST 6175.B6
ST 6141.C6
0,4..1,2 bar 0,8..2,3 bar 1,2..3,3 bar
1,2..2,5 bar
60 mm
60 mm
60 mm
80 mm
PV 6400
Pneumatic heavy duty actuatorsBrands like Honeywell, STI, etc. availableSeries Specification Data Sheet
ST6115 ST6135 ST6160 ST6141 Pneumatic actuators 6100-7010
ST 6175 Pneumatic actuator 6175-7010
Options for pneumatic actuatorsAdditional equipment for actuator types ST 6121, ST 6122
Series Specification Data Sheet
SR 6136 Electric-pneumatic positioner 6136-7010
SR 6138 Electric-pneumatic positioner 6138-7010
RegulatorsRegulators without axillary energy for simple pressure and temperature controls.
• Temperature regulators • Pressure regulators
Temperature regulators
Series Specification Data Sheet
TR 7100
Temperature regulator as a globe valve - heating function closes when the temperature rises
7100-7010
TR 7200
Temperature regulator as a globe valve - cooling function opens when the temperature rises
7200-7010
TR 7300
Temperature regulator as a three-way mixing/diverting valve closes/opens when the temp. rises
7300-7010
TR 7500 Thermostat sensor for valves TR 7100, TR 7200, TR 7300 7400-7010
Pressure regulators
Series Specification Data Sheet
DR7521/ DR7541 Pressure reducing valve closes when the downstream press. rises 7501-7010
DR 7537 Pressure reducing valves internal control connection 7537-7010
DR7621/ DR7641 Excess pressure valve opens when the upstream press. rises 7601-7010
DR7637 Excess pressure valves internal control connection 7637-7010
Bellow Seal Globe valve
Manual stop valves for water, steam, air, thermal oil and other neutral and non aggressive fluids are applicable up to 350°C.
Series Specification Data Sheet
HV 8014 Manual stop valves with bellows seal 8014-7010
Strainers
Strainer for the protection of plant equipment against impurities, suitable for water, steam, air, thermal oil and other neutral and non aggressive fluids up to 350°C.
Series Specification Data Sheet
SF 8090 Strainers 8090-7010
Allied Energy Systems Pte Ltd.66 Tannery Lane# 02-03A Sindo BuildingSingapore 347805Tel : 65 - 6744 8769Fax : 65 - 6836 7373E-mail: [email protected]