pro series diaphragm and piston pumps - air operated diaphragm pump
TRANSCRIPT
PPrroo SSeerriieess DDiiaapphhrraaggmm aanndd PPiissttoonn PPuummppss Ideal for General Industrial and OEM installation applications.
Non-Metallic and Metallic Diaphragm Pumps
Low-Ratio Piston Pumps
Specialty Pumps
Introducing the New High-Performance Pro’s: PD05, PD03
AA
CC
BBAA
BB
CC
Diaphragm Moving from Left to RightUnbalanced valve design eliminates valve centering and pump stall-out-even under low air inlet pressures.
“D” Valve
� Provides a positive seal.
� Helps insure optimum energyefficiency while avoiding costly air “blow-by.”
� Ceramic construction insures long service life.
“SimulShift™” Valve
� Provides an ultra-positive, reliable shift signal that avoids stall-out.
� Provides faster pump trip-over with more flow.
� Faster trip-over with less pulsation and superior laminar material flow.
1.) The diaphragm pushes the right ActuatorPin (B) mechanically moving the Simul-Shift Valve (A) to the left.
2.) Compressed air flows to the large side ofthe Simul-Shift Valve, pneumaticallymoving the valve to the position shown.
3.) Compressed air also flows to the large endof the Major Air Valve (C), pneumaticallyshifting it to the left.
At end of stroke:1.) Diaphragm pushes Pin (B) and Simul-Shift
Valve (A) to the right.2.) Large ends of Simul-Shift Valve (A) and
Major Valve (C) are vented to exhaust pilot signal.
3.) Constant compressed air supply acting onthe smaller areas of the Simul-Shift Valveand Major Valve shifts both valves to theright and hold them in position until thenext cycle begins
Diaphragm Moving Right to Left
1
ProductivityMaximized flow rates + Minimized pulsation and air consumption = Maximum Performance
VersatilityMultiple porting options available along with interface options allow you to customize thispump specifically to your OEM application.
ReliabilityLube Free Patented Differential Valve both on Major air valve and Simulshift (Pilot Valve)provides reliable Worry Free Operation – Fluid On demand every time
Environmentally SoundBolted Construction in conjunction with a wide range of material options providesmaximum chemical and leak resistance
ServiceabilityModular Construction, reduced parts count and simple to use repair kits will minimizerepair time and cost
Don’t forget the other compelling reasons to use Aro Diaphragm Pumps: ARO Diaphragm pumps are simple to apply to your application because they are self priming and can be run at variable flows controlledby air pressure or fluid back pressure. They can handle materials that are abrasive and/or shear sensitive.They can also be run dry without damage to the pump.
Big Delivery. High-Performance. The maker of the best-selling 1/2-inch diaphragm pump in the world, just got better!
Numerical IndexPro-Series Pumps
104104-N02 Pump Speed Control 48104104-N04 Pump Speed Control 48104104-N06 Pump Speed Control 48104255 Repair Kit 3523644-400 Over Run Control 4959916-1 Pneumatic Liquid Level Sensor 4859916-2 Pneumatic Liquid Level Sensor 4861113 Wall Mount 29, 31, 33, 49612041-X 1:1 Ratio Piston Pump 28612042-1 1:1 Ratio Piston Pump 2861412 Siphon Tube 4961879 Muffler 29, 4962133 Wall Mount 4762274 Air Line Lubricant 49635040 Over Run Control 49635043 Over Run Control 49637010 Fluid Section Service Kit 33637010-4 Fluid Section Service Kit 33637010-6 Fluid Section Service Kit 33637081 Fluid Section Service Kit 28637083 Fluid Section Service Kit 28637084 Air Section Service Kit 28637118-C Air Section Service Kit 8, 10, 12, 18, 20637119-XX-C Fluid Section Service Kit 18637124-XX Fluid Section Service Kit 20637140-XX Fluid Section Service Kit 35637141 Air Section Service Kit 35637161-XX-C Fluid Section Service Kit 8637165-XX Fluid Section Service Kit 10, 12637176 Fluid Section Service Kit 33637226 Repair Kit 40637227-B Repair Kit 41, 42637228 Fluid Section Service Kit 33637316 Air Section Service Kit 33637334 Repair Kit 35637335 Repair Kit 35637338 Air Section Service Kit 38637339 Fluid Section Service Kit 38637339-1 Fluid Section Service Kit 38637428 Air Section Service Kit 4, 6, 16637434 Air Section Service Kit 22, 24637438 Exhaust Muffler Kit 6, 16, 50637377 Air Section Service Kit 30637378-X31 Fluid Section Service Kit 30637379-X31 Fluid Section Service Kit 30637427-XX Fluid Section Service Kit 6, 16637429-XX Fluid Section Service Kit 4637432-XX Fluid Section Service Kit 22637433-XX Fluid Section Service Kit 24637440-X Dual Inlet/Outlet Kits 765109 Siphon Tube 47651100 Pneumatic Material Agitator 47651103 Pneumatic Material Agitator 47651851 Drum Cover 4966073-1 Air Line Connection Kit 4, 6, 16, 30, 33, 35,
40, 41, 4266073-2 Air Line Connection Kit 8, 1866084-1 Air Line Connection Kit 10, 12, 2066100 Wall Mount 4766312 Air Line Connection Kit 22, 2466333-B Wet-Sol, Quart 4966334-B Wet-Sol, Gallon 496661AX-X-C 1" Non-Metallic Pump 866610X-X-C 1" Metallic Pump 186661TX-X-C 1-1/2" Non-Metallic Pump 1066615X-X-C 1-1/2" Metallic Pump 20
6662AX-X-C 2" Non-Metallic Pump 12666250-X-C 2" Metallic Pump 22666300-X-C 3" Metallic Pump 2466779 Siphon Tube 4766779-1 Siphon Tube 4766779-2 Siphon Tube 4766779-3 Siphon Tube 4766971 Drum Cover 4766975 Cycle Counter 4767055-B Drum Cover 4767072 Countdown Batcher 4767078 Flange Connection Kit 967079 Flange Connection Kit 1167080 Flange Connection Kit 1367142 Wall Mount 39, 4767161-2 Mini-Batch Counter 4867165-1 Solenoid Actuation Kit 4867165-2 Solenoid Actuation Kit 4867166-1 Solenoid Actuation Kit 4867166-2 Solenoid Actuation Kit 4867168 Cycle Sensor 4767169 Cycle Sensor 4767174-15 Screened Inlet Kit 21, 4867174-20 Screened Inlet Kit 23, 4867388 Wall Mount 5, 4776763 Wall Mount 7, 17, 4794422 Drum Cover 47A212SD-120-A PE Series Pump Control 50A212SS-120-A PE Series Pump Control 50A212SD-012-D PE Series Pump Control 50A212SS-012-D PE Series Pump Control 50A212SD-024-D PE Series Pump Control 50A212SS-024-D PE Series Pump Control 50A212PS PE Series Pump Control 50A212PD PE Series Pump Control 50CBW Connector 48CHW Connector 48C28121-600 Air Line Treatment Combo 28C28453-810 F-R-L Trio 43C28463-810 F-R-L Trio 43DAB05-X-X-X Drum Pump Packages 34H254SS-024-D Air Control Actuation Valve 48H254SS-120-A Air Control Actuation Valve 48LP3001-1 Grease Package 41LP3003-1 Grease Package 42LP310X-X-B Oil Packages 40MQ3728-024-D Air Control Actuation Valve 48MQ3728-120-A Air Control Actuation Valve 48MQ3729-024-D Air Control Actuation Valve 48MQ3729-120-A Air Control Actuation Valve 48NM2202X-X1-X31 2:1 Ratio Piston Pump 30NM2304A-X1-X11 4:1 Ratio Piston Pump 32NM2304B-X1-X1X 4:1 Ratio Piston Pump 32PD03P-X-X 3/8" Non-Metallic Pump 4PD05P-X-X-B 1/2" Non-Metallic Pump 6PD05X-X-B 1/2" Metallic Pump 16PE0XX-XXX-XXX-B0S PE Series w/B0S Specialty Code 50PH10A-XSS-XXT 3:1 Ratio Dia. Pump 38P237AX-EU Centrifugal Pump 43P29231-610 Filter-Regulator 38P35A1-EU Centrifugal Pump 43SB10X-X-X Pulsation Dampener 44SB20X-X-X Pulsation Dampener 45SB30X-X-X Pulsation Dampener 45
MODEL DESCRIPTION PAGE MODEL DESCRIPTION PAGE
2
Model 3/8" 1/2" 1" 1-1/2" 2"
Maximum Flow 10.6 14.4 47 100 145GPM (LPM) (40.1) (54.5) (178) (378.5) (548.8)
MaximumDischarge 100 100 120 120 120Pressure (6.8) (6.8) (8.3) (8.3) (8.3)
PSI (BAR)
Fluid Ports 3/8" (F) - In/Out 1/2" (F) - In/Out 1" ANSI/DIN Flange 1-1/2" ANSI/DIN 2" ANSI/DINInlet/Outlet 1” (F) Threaded Flange Flange
(BSP Available)
Materials Polypropylene Polypropylene Polypropylene Polypropylene Polypropyleneof Groundable Groundable PVDF PVDF PVDF
Construction Acetal AcetalPVDF PVDF
Pump 4.2 (1.9) PD03P-XDS-X 6.3 (2.9) PD05P-XDS-X-B 20.3 (9.2) Poly 62 (28.1) Poly 62 (28.1) PolyWeight 4.3 (1.9) PD03P-XES-X 6.7 (3.0) PD05P-XES-X-B 28.5 (12.9) PVDF 92 (41.7) PVDF 92 (41.7) PVDF
lbs. (kg.) 4.5 (2.0) PD03P-XKS-X 6.8 (3.1) PD05P-XKS-X-B 28.8 (13.1) Poly w/ 85 (38.5) Poly w/ 85 (38.5) Poly w/4.6 (2.1) PD03P-XLS-X 7.2 (3.3) PD05P-XLS-X-B Cast Iron Center Cast Iron Center Cast Iron Center3.4 (1.6) PD03P-XPS-X 5.2 (2.4) PD05P-XPS-X-B 37 (16.8) PVDF w/ 115 (52.1) PVDF w/ 115 (52.1) PVDFw/3.5 (1.6) PD03P-XRS-X 5.4 (2.5) PD05P-XRS-X-B Cast Iron Center Cast Iron Center Cast Iron Center
MaximumSolids 1/16 3/32 1/8 1/4 1/4
Inches (mm) (1.6) (2.4) (3.2) (6.4) (6.4)
Best PD03P-ARS-PAA PD05P-ARS-PUU-B 6661A3-3EB-C 6661T3-3EB-C 6662A3-3EB-CSelling PD03P-ARS-STT PD05P-ARS-PAA-B 6661A3-344-C 6661T3-344-C 6662A3-344-CModels PD03P-AES-DTT PD05P-ARS-PTT-B 6661B3-344-C 6661U3-344-C 6662B3-344-C(BSP PD03P-ALS-KTT PD05P-AES-STT-B 6661A4-444-C 6661U4-444-C 6662B4-444-C
Available) PD05P-ALS-KTT-B 6661B4-444-CPD05P-AES-SST-B
RecommendedFilter/ P29122-600 P29122-600 P29221-610 P29241-610 P29241-610
Regulator
Air Line Kit 66073-1 66073-1 66073-2 66084-1 66084-1
Model Overview: Non-Metallic ModelsPro-Series Pumps
3
3/8" Non-Metallic ModelsPro-Series Pumps
3/8" Non-Metallic Performance SpecificationsRatio: 1:1Maximum Flow: 10.6-g.p.m. (40.1-l.p.m.)Displacement per cycle: 0.022-Gallons (0.083-Liters)Air Inlet: (Female) 1/4 - 18 P.T.F. SAE ShortFluid Inlet: 3/8 - 18 N.P.T.F. - 1
Rp 3/8 (3/8 - 19 BSP, parallel)Fluid Outlet: 3/8 - 18 N.P.T.F. - 1
Rp 3/8 (3/8 - 19 BSP, parallel)Max. operating pressure: 100-psi (6.9-bar)Suspended solids max. dia.: 1/16-in. (1.6-mm)Weight: lbs (kg)
PD03P-XDS-XXX 4.2 (1.9)PD03P-XES-XXX 4.3 (1.9)PD03P-XKS-XXX 4.5 (2.0)PD03P-XLS-XXX 4.6 (2.1)PD03P-XPS-XXX 3.4 (1.6)PD03P-XRS-XXX 3.5 (1.6)
Maximum dry suction lift: 8.5-ft (2.6-m) PTFE (Teflon®) fitted
AccessoriesAir Line Connection Kit* | Kit No. 66073-1Kit includes Piggyback Filter/Regulator with gauge, pipe nipple and a 5-foot section of air hose.
Wall Mount Bracket Kit | Kit No. 67388
Service Repair Kits | Kit No. 637428 (air section)Kit No. 637429-XX (fluid section)
*Please note pumps are not included with these kits.** See options on page 47
Ordering Menu
PX03 P X X S X X X XXX
ModelSeries
D StandardE Remote
ActuationCapable
CenterSectionMaterial
P Polypropylene
FluidConnection
A 3/8" N.P.T.B 3/8" BSP
Fluid Caps/ManifoldMaterial
D Groundable Acetal(single port)
E GroundableAcetal (multiple port)
K PVDF(single port)
L PVDF(multiple port)
P Polypropylene (single port)
R Polypropylene (multiple port)
HardwareMaterial
S Stainless Steel
SeatMaterial
D AcetalK PVDFP PolypropyleneS Stainless
Steel
BallMaterial
A Santoprene®
C Hytrel®
S StainlessSteel
T PTFE (Teflon)V Viton®
DiaphragmMaterial
A SantopreneC HytrelT PTFE (Teflon)
/Santoprene®
V Viton
- No Extension,Standard
- - -
4
Hytrel®, Teflon® and Viton® are registered trademarks of the DuPont company.Santoprene® is a registered trademark of Monsanto Company, licensed toAdvanced Elastomer Systems, L.P.
-BOS RemoteActuationCapable**
Wall Mount Bracket Kit67388
3/8" Non-Metallic Dimensions and Flow CurvesPro-Series Pumps
3/8" Non-Metallic Dimensions and Flow Charts
5
NON-METALLIC
Refer to www.irtools.com/aro/ for full size flow curves.
For additional information contact technical support at (800)495-0276
Dual Inlet/Outlet Kits:637442-1 (N.P.T. Poly)637442-4 (BSP Poly)637442-3 (N.P.T. PVDF)637442-6 (BSP PVDF)637442-2 (N.P.T. Acetal)637442-5 (BSP Acetal)
PE03P-APS-PAA-B0S with 637442-1 Kit
1/2" Non-Metallic ModelsPro-Series Pumps
1/2" Non-Metallic Performance SpecificationsRatio: 1:1Maximum Flow: 14.4-g.p.m. (54.5-l.p.m.)Displacement per cycle: .039-Gallons (.15-Liters)Air Inlet: (Female) 1/4 - 18 P.T.F. SAE ShortFluid Inlet: 1/2 - 14 N.P.T.F. - 1
Rp 1/2 (1/2 -14 BSP, parallel)Fluid Outlet: 1/2 - 14 N.P.T.F. - 1
Rp 1/2 (1/2 -14 BSP, parallel)Max. operating pressure: 100-psi (6.8-bar)Suspended solids max. dia.: 3/32” (2.4-mm)Weight: lbs (kg) PD05P-XDS-XXX-B 6.3 (2.9)
PD05P-XES-XXX-B 6.7 (3.0)PD05P-XKS-XXX-B 6.8 (3.1)PD05P-XLS-XXX-B 7.2 (3.3)PD05P-XPS-XXX-B 5.2 (2.4)PD05P-XRS-XXX-B 5.4 (2.5)
Maximum dry suction lift: 7.9-ft (2.4-m) PTFE fitted
AccessoriesAir Line Connection Kit* | Kit No. 66073-1Kit includes Piggyback Filter/Regulator with gauge, pipe nipple and a 5-foot section of air hose.
Exhaust Threaded Muffler Kit | Kit No. 637438
Service Repair Kits | Kit No. 637428 (air section)Kit No. 637427-XX (fluid section)
Wall Mount | 76763*Please note pumps are not included with these kits.** See options on page 47
Ordering Menu
PX05 P X X S X X X BXX
ModelSeries
D StandardE Remote
ActuationCapable
CenterSectionMaterial
P Polypropylene
FluidConnection
A 1/2" N.P.T.B 1/2" BSP
Fluid Caps/ManifoldMaterial
D Groundable Acetal(single port)
E GroundableAcetal (multiple port)
K PVDF(single port)
L PVDF(multiple port)
P Polypropylene (single port)
R Polypropylene (multiple port)
HardwareMaterial
S Stainless Steel
SeatMaterial
D AcetalK PVDFP PolypropyleneS Stainless
Steel
BallMaterial
A SantopreneC Hytrel*S Stainless
SteelT PTFE (Teflon)U PolyurethaneV Viton
DiaphragmMaterial
A SantopreneC Hytrel*T PTFE (Teflon)/
SantopreneU PolyurethaneV Viton
SpecialtyCode
B StandardB0S Remote
ActuationCapable**
- - -
* Hytrel replaces Nitrile producing superiorchemical compatibility and diaphragm life
6
1/2" Non-Metallic Dimensions and Flow CurvesPro-Series Pumps
1/2" Non-Metallic Dimensions and Flow Charts
Dual Inlet/Outlet Kits:637440-1 (N.P.T. Poly)637440-4 (BSP Poly)637440-2 (N.P.T. Acetal)637440-5 (BSP Acetal)637440-3 (N.P.T. PVDF)637440-6 (BSP PVDF)
Refer to www.irtools.com/aro/ for full size flow curves.
For additional information contact technical support at (800)495-0276
7
NON-METALLIC
PE05P-APS-PAA-B0S with 637440-1 Kit
1" Non-Metallic ModelsPro-Series Pumps
1" Non-Metallic Performance SpecificationsRatio: 1:1Maximum Flow: 47-g.p.m. (177.9-l.p.m.)Displacement per cycle: 0.17-Gallons (0.64-Liters)Air Inlet: (Female) 1/4 - 18 N.P.T.Fluid Inlet: 1 - 11-1/2 N.P.T.F. - 1
Rp 1 (1 - 11 BSP, parallel)1” ANSI/DIN Flange
Fluid Outlet: 1 - 11-1/2 N.P.T.F. - 1Rp 1 (1 - 11 BSP, parallel)1” ANSI/DIN Flange
Max. operating pressure: 120-psi (8.3-bar)Suspended solids max. dia.: 1/8-inch (3.2-mm)Weight: lbs (kg)
6661A3-, 1AF-, 1AJ-, 1AL- 20.3 (9.2)6661A4-, 1AG-, 1AK-, 1AN- 28.5 (12.9)6661B3-, 1BF-, 1BJ-, 1BL- 28.8 (13.1)6661B4-, 1BG-, 1BK-, 1BN- 37.0 (16.8)
Maximum dry suction lift: 15-ft (4.6-m) Rubber fitted
AccessoriesAir Line Connection Kit* | Kit No. 66073-2Kit includes Piggyback Filter/Regulator with gauge, pipe nipple and a 5-foot section of air hose.
Service Repair Kits | Kit No. 637118-C (air section)Kit No. 637161-XX-C (fluid section)
Flange Connection Kit | Kit No. 67078 (for 1" Non-Metallic Pumps)For pumps with inlet/outlet flange manifolds. Kit meets ANSI specifications. Flange constructedof glass-filled polypropylene. Bolts, washers and nuts are stainless steel. Gasket is 4401 klingersynthetic fiber nitrile binder.*Please note pumps are not included with these kits.
Ordering Menu
6661X X X X X C
CenterBody
A AluminumB Cast Iron
Fluid Caps/ManifoldMaterial
3 Polypropylene Flange(3-piece manifold)
4 PVDF Flange (3-piece manifold)
F Polypropylene Flange(one-piece manifold)
G PVDF Flange (one-piece manifold)
J Polypropylene N.P.T.threads (one piecemanifold)
K PVDF N.P.T. threads(one-piece manifold)
L Polypropylene BSPthreads (one-piecemanifold)
N PVDF BSP threads(one-piece manifold)
SeatMaterial
2 316 Stainless Steel3 Polypropylene4 PVDF8 Hard 400 Stainless
Steel
Ball Check Material3 Viton4 PTFE (Teflon)8 PolyurethaneA 316 Stainless SteelC HytrelE Santoprene
DiaphragmMaterial
3 Viton4 PTFE (Teflon) /
Santoprene9 HytrelB Santoprene
- -
8
Flange Connection Kit67078
1" Non-Metallic Dimensions and Flow CurvesPro-Series Pumps
Refer to www.irtools.com/aro/ for full size flow curves.
For additional information contact technical support at (800)495-0276
9
NON-METALLIC
1-1/2" Non-Metallic ModelsPro-Series Pumps
1-1/2" Non-Metallic Performance SpecificationsRatio: 1:1Maximum Flow: 100-g.p.m. (378.5-l.p.m.)Displacement per cycle: .67-Gallons (2.54-Liters)Air Inlet: (Female) 1/2 - 14 N.P.T.F. - 1Fluid Inlet: 1-1/2” A.N.S.I./DIN FlangeFluid Outlet: 1-1/2” A.N.S.I./DIN FlangeMax. operating pressure: 120-psi (8.3-bar)Suspended solids max. dia.: 1/4-in. (6.4-mm)Weight: lbs (kg)
6661T3-X-C 62 (28.1)6661T4-X-C 92 (41.7)
Note: Add 23-lbs (10.4-kg) for cast iron air motor section
Maximum dry suction lift: 14-ft (4.27-m) Rubber fitted
Ordering Menu
6661X X X X X C
CenterBody
T AluminumU Cast Iron
Fluid Caps/ManifoldMaterial
3 Polypropylene Flange(3-piece manifold)
4 PVDF Flange (3-piece manifold)
SeatMaterial
2 316 Stainless Steel3 Polypropylene4 PVDF8 Hard 400 Stainless
Steel
Ball Check Material3 Viton4 PTFE (Teflon)8 PolyurethaneC HytrelE Santoprene
DiaphragmMaterial
3 Viton4 PTFE (Teflon) /
Santoprene9 HytrelB Santoprene
- -
AccessoriesAir Line Connection Kit* | Kit No. 66084-1Kit includes Piggyback Filter/Regulator with gauge, pipe nipple and a 5-foot section of air hose.
Service Repair Kits | Kit No. 637118-C (air section)Kit No. 637165-XX (fluid section)
Flange Connection Kit | Kit No. 67079 (for 1-1/2" Non-Metallic Pumps)For pumps with inlet/outlet flange manifolds. Kit meets ANSI specifications. Flange constructed of glass-filledpolypropylene. Bolts, washers and nuts are stainless steel. Gasket is 4401 klinger synthetic fiber nitrile binder.*Please note pumps are not included with these kits.
10
Flange Connection Kit67079
1-1/2" Non-Metallic Dimensions and Flow CurvesPro-Series Pumps
1-1/2" Non-Metallic Dimensions and Flow Charts
Refer to www.irtools.com/aro/ for full size flow curves.
For additional information contact technical support at (800)495-0276
11
NON-METALLIC
2" Non-Metallic ModelsPro-Series Pumps
2" Non-Metallic Performance SpecificationsRatio: 1:1Maximum Flow: 145-g.p.m. (548.8-l.p.m.)Displacement per cycle: 0.72-Gallons (2.7-Liters)Air Inlet: (Female) 1/2 - 14 N.P.T.F. - 1Fluid Inlet: 2” A.N.S.I./DIN FlangeFluid Outlet: 2” A.N.S.I./DIN FlangeMax. operating pressure: 120-psi (8.3-bar)Suspended solids max. dia.: 1/4-in. (6.4-mm)Weight: lbs (kg)
6662A3-X-C 62 (28.1)6662A4-X-C 92 (41.7)
Note: Add 23-lbs (10.4-kg) for cast iron air motor section
Maximum dry suction lift: 14-ft (4.27-m) Rubber fitted
Ordering Menu
6662X X X X X C
CenterBody
A AluminumB Cast Iron
Fluid Caps/ManifoldMaterial
3 Polypropylene Flange(3-piece manifold)
4 PVDF Flange (3-piece manifold)
SeatMaterial
2 316 Stainless Steel3 Polypropylene4 PVDF8 400 Stainless Steel
Ball Check Material3 Viton4 PTFE (Teflon)8 PolyurethaneC HytrelE Santoprene
DiaphragmMaterial
3 Viton4 PTFE (Teflon) /
Santoprene9 HytrelB Santoprene
- -
AccessoriesAir Line Connection Kit* | Kit No. 66084-1Kit includes Piggyback Filter/Regulator with gauge, pipe nipple and a 5-foot section of air hose.
Service Repair Kits | Kit No. 637118-C (air section)Kit No. 637165-XX (fluid section)
Flange Connection Kit | Kit No. 67080 (for 2" Non-Metallic Pumps)For pumps with inlet/outlet flange manifolds. Kit meets ANSI specifications. Flange constructed of glass-filledpolypropylene. Bolts, washers and nuts are stainless steel. Gasket is 4401 klinger synthetic fiber nitrile binder.
*Please note pumps are not included with these kits.
12
Flange Connection Kit67080
2" Non-Metallic Dimensions and Flow CurvesPro-Series Pumps
2" Non-Metallic Dimensions and Flow Charts
Refer to www.irtools.com/aro/ for full size flow curves.
For additional information contact technical support at (800)495-0276
13
NON-METALLIC
Value PropositionPro-Series Pumps
14
[1] “Unbalanced” Major Air Valve� Unbalanced valve design
eliminates valve centering and pump stall-out, even underlow air inlet pressures.
� “O” Ring seals prevent waste of expensive compressed air.Air flow stops when fluid flowstops.
� Maintenance is simple: just replace the worn “O” Rings and“U” Cups.
[2] Independent Pilot Rod� Utilizes pneumatics and
mechanical action to shift Pilot Rod. Ensures positivepilot signal, avoiding stall-out.
[3] Broad Material Selection� Options allow you to optimize
compatibility betweenthe pump and fluid beingmoved.
� Non-Metallic Diaphragm Pumps are available in polypropylene, PVDF andgroundable acetal. Checkmodels for availability.
� Metallic Diaphragm Pumps are available in aluminum,stainless steel and cast iron.Check models for availability.
[4] Diaphragm/Ball Check Options� Fit your pump with the
diaphragms and ball checksneeded to maximize fluidcompatibility and abrasionresistance.
1
2
34
Ingersoll Rand Diaphragm Pumps:Keys to ARO Air Motor Technology
Introducing the New High-Performance Pro’s: PD05, PD03: Aro’snew Pro Series family has all new members at both ends of the delivery spectrum. In the low-to-medium flow range, we offer ournew PD05 (1/2") and PD03 (3/8") models. Featuring our patented airvalve technology, including Simul Shift and D-Valve designs, users areassured of stall-free operation, with optimum energy efficiency.These pumps also feature fluid deliveries previously unavailable inport sizes like these: 14.4 GPM (1/2") and 10.4 (3/8")...that’s impressive delivery in a small package! ARO pioneered the 1/2",high-demand, low-maintenance diaphragm pump in the eighties -now its time to step it up-with the new Pro PD0s.
Introducing the New High-Flow Pro’s: 666250 and 666300: At the farend of the fluid delivery spectrum, the new ARO Pro Series 2" and 3"port models feature Aro’s patented “Unbalanced”, stall-free air valve design and bolted construction for leak-tight integrity. Withmaximum delivery rates of 172 GPM (2") and 237 GPM (3"), the newhigh-flow Pros are the ideal answer to big volume applications - whereperformance with economy are a must.
MODEL 1/2" 1" 1-1/2" 2" 3"
Maximum Flow 12 35 90 172 237GPM (LPM) (45.4) (133) (340.7) (651) (897)
MaximumDischarge 100 120 120 120 120Pressure (6.9) (8.3) (8.3) (8.3) (8.3)
PSI (BAR)
Fluid Ports 1/2" (F) - In/Out 1" (F) - In/Out 1-1/2" (F) In/Out 2" (F) In/ Out 3" (F) In/ OutInlet/Outlet
(BSP Available)
Materials Aluminum Aluminum Aluminum Aluminum Aluminumof Stainless Steel Stainless Steel Stainless Steel
Construction Cast Iron Cast Iron
Pump 10.4 (4.7) PD05A-XAS-X-B 19 (8.6) Aluminum* 51.5 (23.4) Aluminum* 65.2 (29.6) 109.8 (49.8)Weight 16.6 (7.5) PD05A-XSS-X-B 36 (16.3) Stainless 84.5 (38.3) Stainless
Lbs. (Kg.) 8.0 (3.7) PD05R-XAS-X-B 31 (14.1) Cast Iron* 79.5 (36.1) Cast Iron*14.3 (6.5) PD05R-XSS-X-B
*add 8-lb(3.63-kg) for *add 23-lb(10.4-kg) forcast iron center section cast iron center section
MaximumSolids 3/32 1/8 1/4 1/4 3/8
Inches (mm) (2.4) (3.2) (6.4) (6.4) (9.5)
Best PD05R-AAS-STT-B 666100-3C9-C 666150-3EB-C 666250-EEB-C 666300-EEB-CSelling PD05R-ASS-STT-B 666100-344-C 666150-3C9-C 666250-144-C 666300-144-CModels PD05A-AAS-PCC-B 666101-344-C 666150-344-C 666250-9C9-C 666300-9C9-C(BSP PD05R-AAS-FTT-B 666101-3EB-C 666151-3EB-C 666270-EEB-C 666320-EEB-C
Available) PD05R-AAS-FAA-B 666111-244-C 666151-344-C 666270-144-C 666320-144-CPD05R-AAS-PTT-B 666112-3EB-C 666152-3EB-C 666270-9C9-C 666320-9C9-C
RecommendedFilter/ P29122-600 P29221-610 P29241-610 P29241-610 P29241-610
Regulator
Air Line Kit 66073-1 66073-2 66084-1 66312 66312
Model Overview: Metallic ModelsPro-Series Pumps
15
1/2" Metallic ModelsPro-Series Pumps
1/2" Metallic Performance SpecificationsRatio: 1:1Maximum Flow: 12.0-g.p.m. (45.4-l.p.m.)Displacement per cycle: 0.039-Gallons (0.15-Liters)Air Inlet: (Female) 1/4 - 18 P.T.F. SAE Short (PD05R-X-X-B models)
1/4 - 18 N.P.T.F - 1 (PD05A-X-X-B models)Fluid Inlet: 1/2 - 14 N.P.T.F. - 1
Rp 1/2 (1/2 - 14 BSP, parallel)Fluid Outlet: 1/2 - 14 N.P.T.F. - 1
Rp 1/2 (1/2 - 14 BSP, parallel)Max. operating pressure: 100-psi (6.9-bar)Suspended solids max. dia.: 3/32-in. (2.4-mm)Weight: lbs (kg)
PD05A-XAS-XXX-B 10.4 (4.7)PD05A-XSS-XXX-B 16.6 (7.5)PD05R-XAS-XXX-B 8.0 (3.7)PD05R-XSS-XXX-B 14.3 (6.5)
Maximum dry suction lift: 9.1-ft (2.8-m) PTFE fitted
AccessoriesAir Line Connection Kit* | Kit No. 66073-1Kit includes Piggyback Filter/Regulator with gauge, pipe nipple and a 5-foot section of air hose.
Exhaust Threaded Muffler Kit | Kit No. 637438
Service Repair Kits | Kit No. 637428 (air section)Kit No. 637427-XX (fluid section)
Wall Mount | 76763 * Please note pumps are not included with these kits.** See options on page 47
Ordering Menu
PX05 X X X S X X X BXX
ModelSeries
D StandardE Remote
ActuationCapable
CenterSectionMaterial
A AluminumR Polypropylene
FluidConnection
A 1/2" N.P.T.B 1/2" BSP
Fluid Caps/ManifoldMaterial
A AluminumS Stainless
Steel
HardwareMaterial
S Stainless Steel
SeatMaterial
F AluminumP PolypropyleneS Stainless
Steel
BallMaterial
A SantopreneC Hytrel*S Stainless
SteelT PTFE (Teflon)U PolyurethaneV Viton
DiaphragmMaterial
A SantopreneC Hytrel*T PTFE (Teflon)/
SantopreneV Viton
SpecialtyCode
B StandardB0S Remote
ActuationCapable**
- - -
* Hytrel replaces Nitrile producing superiorchemical compatibility and diaphragm life
16
1/2" Metallic Dimensions and Flow CurvesPro-Series Pumps
1/2" Metallic Dimensions and Flow Charts
Refer to www.irtools.com/aro/ for full size flow curves.
For additional information contact technical support at (800)495-0276
17
METALLIC
1" Metallic ModelsPro-Series Pumps
1" Metallic Performance SpecificationsRatio: 1:1Maximum Flow: 35-g.p.m. (133-l.p.m.)Displacement per cycle: 0.16-Gallons (0.60-Liters)Air Inlet: (Female) 1/4 - 18 N.P.T.F. - 1Fluid Inlet: 1 - 11-1/2 N.P.T.F. - 1
Rp 1 (1-11 BSP parallel)Fluid Outlet: 1 - 11-1/2 N.P.T.F. - 1
Rp 1 (1-11 BSP parallel)Max. operating pressure: 120-psi (8.3-bar)Suspended solids max. dia.: 1/8-in. (3.2-mm)Weight: lbs (kg)
666100-X-C (aluminum) 19 (8.6)666101-X-C (stainless) 36 (16.3)666102-X-C (cast iron) 31 (14.1)
Note: Add 8-lbs (3.63-kg) for cast iron air motor section
Maximum dry suction lift: 20-ft (6.1-m) Rubber fitted
Ordering Menu
6661X X X X X C
Center Body/Threads
0 Aluminum, N.P.T.F.1 Cast Iron, N.P.T.F.2 Aluminum, BSP3 Cast Iron, BSP
Fluid Caps/ManifoldMaterial
0 Aluminum (steelhardware)
1 Stainless Steel (steelhardware)
2 Cast Iron (steelhardware)
9 Stainless Steel, dualoutlet (steel hardware)
A Aluminum, (stainlesshardware)
B Stainless Steel(stainless hardware)
C Cast Iron (stainlesshardware)
D Stainless Steel, dualoutlet (stainlesshardware)
SeatMaterial
1 Aluminum2 316 Stainless3 Polypropylene4 PVDF5 Carbon Steel8 Hard 400 Stainless
Steel
Ball Check Material3 Viton4 PTFE (Teflon)8 PolyurethaneA Stainless SteelC HytrelE Santoprene
DiaphragmMaterial
3 Viton4 PTFE (Teflon) /
Santoprene9 HytrelB Santoprene
- -
AccessoriesAir Line Connection Kit* | Kit No. 66073-2Kit includes Piggyback Filter/Regulator with gauge, pipe nipple and a 5-foot section of air hose.
Service Repair Kits | Kit No. 637118-C (air section)Kit No. 637119-XX-C (fluid section)
*Please note pumps are not included with these kits.
18
1" Metallic Dimensions and Flow CurvesPro-Series Pumps
1" Metallic Dimensions and Flow Charts
Refer to www.irtools.com/aro/ for full size flow curves.
For additional information contact technical support at (800)495-0276
19
METALLIC
1-1/2" Metallic ModelsPro-Series Pumps
1-1/2" Metallic Performance SpecificationsRatio: 1:1Maximum Flow: 90-g.p.m. (340.7-l.p.m.)Displacement per cycle: 0.64-Gallons (2.42-Liters)Air Inlet: (Female) 1/2 - 14 N.P.T.F. - 1Fluid Inlet: 1-1/2 11-1/2 N.P.T.F. - 1
Rp 1-1/2 (1-1/2 - 11 BSP parallel)Fluid Outlet: 1-1/2 11-1/2 N.P.T.F. - 1
Rp 1-1/2 (1-1/2 - 11 BSP parallel)Max. operating pressure: 120-psi (8.3-bar)Suspended solids max. dia.:1/4-inch (6.4-mm)
Weight: lbs (kg)666150-X-C (aluminum) 51.5 (23.4)666151-X-C (stainless) 84.5 (38.3)666152-X-C (cast iron) 79.5 (36.1)
Note: Add 23-lbs (10.4-kg) for cast iron air motor section
Maximum dry suction lift: 19-ft (5.8-m) Rubber fitted
Ordering Menu
6661X X X X X C
Center Body/Threads
5 Aluminum, N.P.T.F.6 Cast Iron, N.P.T.F.7 Aluminum, BSP8 Cast Iron, BSP
Fluid Caps/ManifoldMaterial
0 Aluminum (steelhardware)
1 Stainless Steel (steelhardware)
2 Cast Iron (steelhardware)
A Aluminum, (stainlesshardware)
B Stainless Steel(stainless hardware)
C Cast Iron (stainlesshardware)
SeatMaterial
1 Aluminum2 316 Stainless3 Polypropylene4 PVDF5 Carbon Steel8 400 Stainless Steel
Ball Check Material3 Viton4 PTFE (Teflon)8 PolyurethaneA Stainless SteelC HytrelE Santoprene
DiaphragmMaterial
3 Viton4 PTFE (Teflon) /
Santoprene9 HytrelB Santoprene
- -
AccessoriesAir Line Connection Kit* | Kit No. 66084-1Kit includes Piggyback Filter/Regulator with gauge, pipe nipple and a 5-foot section of air hose.
Service Repair Kits | Kit No. 637118-C (air section)Kit No. 637124-XX (fluid section)
Screened Inlet Kits | Kit No. 67174-15 (for 1-1/2" Metallic Pumps)Prevents unwanted material and debris from entering pump. Kit includes screen and installation hardware.*Please note pumps are not included with these kits.
20
Screened Inlet Kit67174-15
1-1/2" Metallic Dimensions and Flow CurvesPro-Series Pumps
1-1/2" Metallic Dimensions and Flow Charts
(Dimensions shown are for reference only, they are displayed in inches and millimeters (mm).
11-1/2" (292 mm)
19-5/8"(498 mm)
18-3/8"(467 mm)
13-1/8" (333 mm)
11-3/4" (298 mm)
2-3/4"(70 mm)
9" (229 mm)
1/2" Slot (14 mm)
Material Outlet
7-5/8"(194 mm)
12-3/4" (324 mm)
Material Inlet1-1/2 - 11-1/2 N.P.T.F. - 1 (66615X-X-C, 66616 X-X-C)Rp1-1/2 (1-1/2 - 11 BSP parallel) (66617X-X-C, 66618 X-X-C)
Air Inlet1/2 - 14 N.P.T.F. - 1
Air Exhaust Thread3/4 - 14 N.P.T.F. - 1
14-13/16" (376 mm)
1-1/2 - 11-1/2 N.P.T.F. - 1 (66615X-X-C, 66616 X-X-C)Rp1-1/2 (1-1/2 - 11 BSP parallel) (66617X-X-C, 66618 X-X-C)
Refer to www.irtools.com/aro/ for full size flow curves.
For additional information contact technical support at (800)495-0276
21
METALLIC
2" Metallic ModelsPro-Series Pumps
2" Metallic Performance SpecificationsRatio: 1:1Maximum Flow: 172-g.p.m. (651-l.p.m.)Displacement per cycle: 1.4-Gallons (5.3-Liters)Air Inlet: (Female) 3/4 - 14 N.P.T.F. - 1Fluid Inlet: 2 - 11-1/2 N.P.T.F. - 1
Rp 2 (2 - 11 BSP, parallel)Fluid Outlet: 2 - 11-1/2 N.P.T.F. - 1
Rp 2 (2 - 11 BSP, parallel)Max. operating pressure: 120-psi (8.3-bar)Suspended solids max. dia.: 1/4-in. (6.4-mm)Weight: lbs (kg)
6662X0-XXX-C 65.2 (29.6)
Maximum dry suction lift: 27.2-ft (8.3-m) Elastomer fitted
Ordering Menu
6662X X X X X C
Center Body/Threads
5 Aluminum, N.P.T.F.7 Aluminum, BSP
Fluid Caps/ManifoldMaterial
0 Aluminum (steelhardware)
SeatMaterial
1 Aluminum9 HytrelE Santoprene
Ball Check Material4 PTFE (Teflon)C HytrelE Santoprene
DiaphragmMaterial
4 PTFE (Teflon) /Santoprene
9 HytrelB Santoprene
- -
AccessoriesAir Line Connection Kit* | Kit No. 66312Kit includes Piggyback Filter/Regulator with gauge, pipe nipple and a 5-foot section of air hose.
Service Repair Kits | Kit No. 637434 (air section)Kit No. 637432-XX (fluid section)
Screened Inlet Kits | Kit No. 67174-20 (for 2" Metallic Pumps)Prevents unwanted material and debris from entering pump. Kit includes screen and installation hardware.*Please note pumps are not included with these kits.
22
67389 Muffler Kit (not shown)included with pump
Screened Inlet Kit67174-20
2" Metallic Dimensions and Flow CurvesPro-Series Pumps
2" Metallic Dimensions and Flow Charts
Refer to www.irtools.com/aro/ for full size flow curves.
For additional information contact technical support at (800)495-0276
23
METALLIC
3" Metallic ModelsPro-Series Pumps
3" Metallic Performance SpecificationsRatio: 1:1Maximum Flow: 237-g.p.m. (897-l.p.m.)Displacement per cycle: 2.65-Gallons (10.03-Liters)Air Inlet: (Female) 3/4 - 14 N.P.T.F. - 1Fluid Inlet: 3 - 8 N.P.T.F. - 1
Rp 3 (3 - 11 BSP parallel)Fluid Outlet: 3 - 8 N.P.T.F. - 1
Rp 3 (3 - 11 BSP, parallel)Max. operating pressure: 120-psi (8.3-bar)Suspended solids max. dia.: 3/8-in. (9.5-mm)Weight: lbs (kg)
6663X0-XXX-C 109.8 (49.8)
Maximum dry suction lift: 17.6-ft (5.4-m) Elastomer fitted
Ordering Menu
6663X X X X X C
Center Body/Threads
0 Aluminum, N.P.T.F.2 Aluminum, BSP
Fluid Caps/ManifoldMaterial
0 Aluminum (steelhardware)
SeatMaterial
1 Aluminum9 HytrelE Santoprene
Ball Check Material4 PTFE (Teflon)C HytrelE Santoprene
DiaphragmMaterial
4 PTFE (Teflon) /Santoprene
9 HytrelB Santoprene
- -
AccessoriesAir Line Connection Kit* | Kit No. 66312Kit includes Piggyback Filter/Regulator with gauge, pipe nipple and a 5-foot section of air hose.
Service Repair Kits | Kit No. 637434 (air section)Kit No. 637433-XX (fluid section)
*Please note pumps are not included with these kits.
24
67389 Muffler Kit (not shown)included with pump
3" Metallic Dimensions and Flow CurvesPro-Series Pumps
3" Metallic Dimensions and Flow Charts
Refer to www.irtools.com/aro/ for full size flow curves.
For additional information contact technical support at (800)495-0276
25
METALLIC
NotesPro-Series Pumps
26
1:1-to-4:1 Ratio Piston and Diaphragm PumpsPro-Series Pumps
MODEL 1:1 Ratio 2:1 Ratio 4:1 Ratio 1:1 RatioPiston Pump Piston Pump Piston Pump Diaphragm Pump
Maximum Flow 18 4.3 4.4 11GPM (LPM) (68.1) (16.3) (16.8) (41.6)
MaximumInlet 150 150 150 100
Pressure (10.3) (10.3) (10.3) (6.8)PSI (BAR)
Fluid Ports Immersed Inlet 1-1/2" (F) In - CS 1-1/2" (F) In - CS 1/2" Suction Tube InInlet/Outlet 3/4” (F) Out 1-1/4" (F) In - SS 1-1/4" (F) In - SS 1/2" (F), or Hose
(BSP Available) (No BSP) Immersed Immersed Accessory Out3/4" (F) Out 3/4" (F) Out
Materials Carbon Steel Carbon Steel Carbon Steel Polypropyleneof Stainless Steel Stainless Steel Stainless Steel
Construction Aluminum
Pump 13 (5.9) 17.5 (7.9) CS-Stub 32 (14.5) CS-Stub 22 (10) Polypropylene*Weight 19.6 (8.9) CS-55-gallon 46 (20.9) CS-55-gallon 26 (11.8) Aluminum*
Lbs. (Kg.) 17.2 (7.8) SS-Stub 32 (14.5) SS-Stub 36 (16.3) Stainless*22.5 (10.2) SS-55-Gallon 46 (20.9) SS-55-Gallon *basic package shipping weight
MaximumSolids Clean Fluids Clean Fluids Clean Fluids 3/32
Inches (mm) (2.4)
Best 612041-1 NM2202A-11-731 NM2304A-11-311 DAB05-PPAA-2-ASelling 612041-3 NM2202A-41-731 NM2304A-41-311 DAB05-PPTT-2-AModels NM2202B-11-731 NM2304B-11-311 DAB05-SSTT-2-A(BSP NM2202B-41-731 NM2304B-41-311
Available)
RecommendedFilter/ C28123-600 P29122-600 P29122-600 P29122-600
Regulator (Filter/Regulator/Lubricator)
Air Line Kit 66073-1 66073-1 66073-1 66073-1
27
Specialty Pumps 1:1 Ratio Piston ModelsPro-Series Pumps
1:1 Ratio Piston Pump Performance SpecificationsRatio: 1:1Maximum Flow: 18-g.p.m. (68.1-l.p.m.)Max. Working Flow: 9-g.p.m. (34.1-l.p.m.)Maximum Rec’d Cycles: 75 per minuteDisplacement per Cycle: 18.8-In3 (308.0-cm3)Air Inlet: (Female) 1/4 - 18 N.P.T.F. - 1Fluid Inlet: ImmersedFluid Outlet: 3/4 - 14 N.P.T.F. - 1Max. operating pressure: 150-psi (10.3-bar)Fluid Pressure Range: 0-150-psi (0-10.3-bar)Material of Construction: Carbon SteelWeight: lbs (kg)
612041-X 13 (5.9)612042-1 14 (6.4)
Ordering Menus
6 1 2 0 4 X X
ModelSeries
1 For use with 55-gallon drums
2 For use with 275-gallon drums
PackingOption
1 Nitrile3 PTFE (Teflon)
-
AccessoriesAir Line Treatment Combination Unit | C28121-600Unit contains Piggyback Filter/Regulator and Lubricator. Filter/Regulator features a 20 micron filter, poly bowl with guard and 5-125-psi gauge. Lubricator features a poly bowl with guard.Plumb directly to pump’s air inlet.
Service Repair Kits | Kit No. 637084 (air section)Kit No. 637081 (Nitrile lower pump end repair)Kit No. 637083 (Teflon lower pump end repair)
Muffler | 61879Muffler reduces operating noise level of pump.Wall Mount | 61113Wall-Mount Bracket Permits pump to be wall-mounted near fluid container. Bracket can also be attached to side of open 55-gallon drum.
28
Muffler61879
Wall Mount61113
Specialty Pumps 1:1 Ratio Piston Model Dimensions and Flow CurvesPro-Series Pumps
1:1 Ratio Piston Pump Dimensions and Flow Charts
“A”
“B”
Model “A” “B”612041-X 54” (1371.6-mm) 34-5/8” (879.5-mm)612042-1 64-1/4” (1631.9-mm) 44-7/8” (1139.8-mm)
Air Inlet (female)1/4 - 18 N.P.T.F. - 1
Material Outlet (female)3/4 - 14 N.P.T.F. - 1
Material InletImmersed Refer to www.irtools.com/aro/ for full size flow curves.
For additional information contact technical support at (800)495-0276
29
SPECIALTY PUMPS
Specialty Pumps 2:1 Ratio Piston ModelsPro-Series Pumps
2:1 Ratio Piston Pump Performance SpecificationsRatio: 2:1Maximum Flow: 4.3-g.p.m. (16.3-g.p.m.)Flow @ 60-Cycles/min.: 2.15-g.p.m. (8.14-l.p.m.)Maximum Rec’d Cycles: 120 per minuteDisplacement per Cycle: 8.3-In3 (136-cm3)Air Inlet: (Female) 1/4 - 18 N.P.T.F. - 1Fluid Inlet: 1-1/2 - 11-1/2 N.P.T.F. - 1 (NM2202A-X)
1-1/4 - 11-1/2 N.P.T.F. - 1 (NM2202B-X)Fluid Outlet: 3/4 - 14 N.P.T.F. - 1Max. operating pressure: 150-psi (10.3-bar)Fluid Pressure Range: 0-351-psi (0-24.2-bar)Weight: lbs (kg)
NM2202A-11-X31 17.5 (7.9)NM2202A-41-X31 19.6 (8.9)NM2202B-11-X31 17.2 (7.8)NM2202B-41-X31 22.5 (10.2)
Materials of Construction: Carbon SteelStainless Steel
Ordering Menu
NM2202X X 1 X 3 1
ModelSeries
A Carbon SteelB Stainless Steel
ContainerType
1 Universal (Stub)4 55-Gallon Drum
PackingMaterial
7 PTFE (Teflon) upperand lower
B UHMW-PE upper/PTFE (Teflon) lower
C UHMW-PE upper andlower
J Polyurethane upper/UHMW-PE lower
SpringArrangement
3 No Spring
PlungerType
1 StandardCarbon Steel onNM2202A-X modelsStainless Steel onNM2202B-X models
- -
AccessoriesAir Line Connection Kit* | Kit No. 66073-1Kit includes Piggyback Filter/Regulator with gauge, pipe nipple and a 5-foot section of air hose.
Service Repair Kits | Kit No. 637377 (air section)Kit No. 637378-X31 (NM2202A-X fluid section)Kit No. 637379-X31 (NM2202B-X fluid section)
Wall Mount | 61113For use with stub style pumps. Siphon tube then used to connect pump to fluid supply.*Please note pumps are not included with these kits.
--30
Wall Mount61113
Specialty Pumps 2:1 Ratio Piston Model Dimensions and Flow CurvesPro-Series Pumps
2:1 Ratio Piston Pump Dimensions and Flow Charts
Dimensions: Inches (mm)
Model Number: “A” “B”NM2202A-11-X31 34-3/16 (868.0) 20-1/16 (508.8)NM2202A-41-X31 47-7/8 (1214.8) 33-11/16 (855.6)NM2202B-11-X31 33-7/8 (859.9) 19-7/8 (503.7)NM2202B-41-X31 47-3/4 (1211.8) 33-11/16 (855.6)
Refer to www.irtools.com/aro/ for full size flow curves.
For additional information contact technical support at (800)495-0276
31
SPECIALTY PUMPS
Specialty Pumps 4:1 Ratio Piston ModelsPro-Series Pumps
4:1 Ratio Piston Pump Performance SpecificationsRatio: 4:1Maximum Flow: 4.44-g.p.m. (16.79-l.p.m.) NM2304A-X
4.26-g.p.m. (16.12-l.p.m.) NM2304B-XFlow @ 60-Cycles/min.: 2.12-g.p.m. (8.02-l.p.m.) NM2304A-X
2.13-g.p.m. (8.06-l.p.m.) NM2304B-XMaximum Rec’d Cycles: 125 per minute NM2304A-X
120 per minute NM2304B-XDisplacement per Cycle: 8.2-In3 (134.3-cm3)Air Inlet: (Female) 1/4 - 18 N.P.T.F. - 1Fluid Inlet: Immersed Inlet (NM2304A-41, -91, -A1)
1-1/2 - 11-1/2 N.P.T.F. - 1 (NM2304A-11, -81, -B1)1-1/4 - 11-1/2 N.P.S.M. (NM2304B-X)
Fluid Outlet: 3/4 - 14 N.P.T.F. - 1Max. operating pressure: 150-psi (10.3-bar)Fluid Pressure Range: 0-600-psi (0-41.4-bar)Weight: lbs (kg)
NM2304A-11-X11 32 (14.5) NM2304B-11-X1X 32 (14.5)NM2304A-41-X11 46 (20.9) NM2304B-41-X1X 46 (20.9)NM2304A-81-X11 31.4 (14.3)NM2304A-91-X11 45.4 (20.6)NM2304A-A1-X11 31.0 (14.1)NM2304A-B1-X11 32 (14.5)
Lower Pump End Series:NM2304A-X1-X11 67151-X-X11NM2304B-X1-X1X 6510X-X
NM2304B X 1 X 1 X
ModelSeries
Stainless Steel
ContainerType
1 Universal (Stub)4 55-Gallon Drum
PackingMaterial
C UHMW-PE upper andlower
3 PTFE (Teflon) upperand lower
W Viton upper/ PTFE(Teflon) lower
SpringArrangement
1 Coil Spring
PlungerType
1 Standard 300-SeriesStainless Steel
B Ceramic
- -
Ordering Menus
NM2304A X 1 X 1 1
ModelSeries
Carbon Steel
ContainerType
1 Universal (Stub)4 55-Gallon Drum8 Universal (Stub)
without bung9 55-Gallon without
bungA Stub Follower PlateB Universal (Stub) with
alternate bung
PackingMaterial
C UHMW-PE upper andlower
3 Glass-filled Teflonupper Virgin Teflonlower
5 Glass-filled Teflon/Leather staggeredupper Virgin Teflonlower
SpringArrangement
1 Coil Spring
PlungerType
1 Standard CarbonSteel
- -
32
Specialty Pumps 4:1 Ratio Piston Model Dimensions and Flow CurvesPro-Series Pumps
4:1 Ratio Piston Pump Dimensions and Flow Charts
Dimensions: Inches (mm)
Model Number: “A” “B”NM2304A-11-X11 30-1/4 (768.5) 11-3/4 (297.7)NM2304A-41-X11 55-5/8 (1413.0) 37-1/8 (942.2)NM2304A-81-X11 30-1/4 (768.5) 11-3/4 (297.7)NM2304A-91-X11 55-5/8 (1413.0) 37-1/8 (942.2)NM2304A-A1-X11 29-9/16 (751.0) 11-1/16 (280.2)NM2304A-B1-X11 30-1/4 (768.5) 11-3/4 (297.7)NM2304B-11-X1X 28-1/8 (714.4) 9-23/32 (246.8)NM2304B-41-X1X 51-21/32 (1312.1) 33-1/4 (844.6)
Refer to www.irtools.com/aro/ for full size flow curves.
For additional information contact technical support at (800)495-0276
AccessoriesAir Line Connection Kit* | Kit No. 66073-1Kit includes Piggyback Filter/Regulator with gauge, pipe nipple and a 5-foot section of air hose.
Service Repair Kits | Kit No. 637316 (air section)Kit No. 637176 (NM2304A-X: 67151-X-311, -X-511 fluid section)Kit No. 637228 (NM2304A-X: 67151-X-C11 fluid section)Kit No. 637010 (NM2304B-X: 65106, 65108, 65108-5 fluid section)Kit No. 637010-4 (NM2304B-X: 65106-4, 65108-4, 65108-6 fluid section)Kit No. 637010-6 (NM2304B-X: 65108-8 fluid section)
Wall Mount | 61113For use with stub style pumps. Siphon tube then used to connect pump to fluid supply.*Please note pumps are not included with these kits.
33
SPECIALTY PUMPS
Wall Mount61113
Specialty Pumps - Drum PumpsPro-Series Pumps
1:1 Ratio Drum Pump Performance SpecificationsRatio: 1:1Maximum Flow: 11-g.p.m. (41.6-l.p.m.)Displacement per cycle: .039-Gallons (.15-Liters)Air Inlet: (Female) 1/4 -18 N.P.T.Fluid Inlet: Siphon Tube for 55-Gallon DrumFluid Outlet: 1/2 -14 N.P.T.F. - 1Max. operating pressure: 100-psi (6.8-bar)Suspended solids max. dia.: 3/32-in. (2.4-mm)Shipping Weight: lbs (kg) 22 (10) Polypropylene, basic package
26 (11.8) Aluminum, basic package36 (16.3) Stainless, basic package
34
Ordering Menu
MODEL PUMP HOUSING PUMP DIA. LOCK OUT VALVE FOOT 10’ HOSE DISPENSE FLUIDNO. and SEATS and BALLS (P/N 104253-2) VALVE ASM VALVE SERVICEDAB05-PPTT-2-A POLYPROPYLENE PTFE (Teflon) X - - - ACIDS & CAUSTICSDAB05-PPCC-2-A POLYPROPYLENE HYTREL X - - - OILDAB05-PPUU-2-A POLYPROPYLENE POLYURETHANE X - - - WATER/OILDAB05-PPAA-2-A POLYPROPYLENE SANTOPRENE X - - - MILD ACIDS/MILD CAUSTICSDAB05-PPCC-2-N POLYPROPYLENE HYTREL X - NITRILE - OILDAB05-PPCC-B-M POLYPROPYLENE HYTREL X X NITRILE NO-DRIP OILDAB05-PPAA-2-B POLYPROPYLENE SANTOPRENE X - EPDM - MILD ACIDS/MILD CAUSTICSDAB05-PPUU-2-C POLYPROPYLENE POLYURETHANE X - VINYL - WATER/OILDAB05-PPCC-B-J POLYPROPYLENE HYTREL X X REINFORCED NITRILE X OILDAB05-PPAA-B-K POLYPROPYLENE SANTOPRENE X X EPDM X MILD ACIDS/MILD CAUSTICSDAB05-SSTT-2-A STAINLESS STEEL PTFE (Teflon) X - - - SOLVENTDAB05-ASTT-2-A ALUM./SS. PTFE (Teflon) X - - - SOLVENTDAB05-APCC-2-A ALUM./POLY. HYTREL X - - - OIL/SOME SOLVENTSDAB05-APCC-2-O ALUM./POLY. HYTREL X - NITRILE - OIL/SOME SOLVENTSDAB05-APCC-B-P ALUM./POLY. HYTREL X X NITRILE NO-DRIP OIL/SOME SOLVENTSDAB05-APCC-B-D ALUM./POLY. HYTREL X X - X OIL/SOME SOLVENTSDAB05-APCC-B-L ALUM./POLY. HYTREL X X REINFORCED NITRILE X OIL/SOME SOLVENTSDAB05-ASAA-2-A ALUM./S.S. SANTOPRENE X - - - WATER
Drum Pumps• Choose from Aluminum, Stainless Steel or Polypropylene body
construction - ARO Drum Pumps are available in three bodymaterials for optimum fluid compatibility.
Drum Pump Packages• Package Components Factory-Matched - ARO Drum Pump
package components contain pre-specified, matching materialsof construction for complete fluid compatibility.
• Choose from Basic to Complete - Drum Pump Packages can be ordered in 3 styles:
• Basic: Pump, Bung Adapter, Air Safety Shut-Off, Siphon Tube, Weather Seal and base
• Complete/Transfer: Basic Pump plus Fluid Hose or Fluid Hose with Non-Drip Nozzle
• Complete/ Dispensing: Basic Pump plus Foot Valve, Hose and Dispensing Nozzle
Pump Features• 11-g.p.m. Flow Capability - Drum Pumps offer plenty of
capacity to satisfy a broad range of transfer applicationvolume demands.
• Stall-Free Operation - ARO Diaphragm Drum Pumps feature a patented “unbalanced” air valve design that avoids stall-out,even under low air-inlet pressures.
• Bolted Construction - ARO Diaphragm Drum Pumps utilize bolted fasteners for leak-tight integrity.
• 5-Year Warranty
Specialty Pumps - Drum Pump Dimensional DataPro-Series Pumps
1:1 Ratio Drum Pump Dimensional Data
AccessoriesAir Line Connection Kit* | Kit No. 66073-1Kit includes Piggyback Filter/Regulator with gauge, pipe nipple and a 5-foot section of air hose.
Service Repair Kits | Kit No. 637428 (air section)Kit No. 637427-XX (fluid section)Kit No. 104255 (for repair of P29122-600 piggyback filter/regulator)Kit No. 637334 (for repair of 95199 dispensing nozzle)Kit No. 637335 (for repair of 95183 oil spigot)
*Please note pumps are not included with these kits.
35
SPECIALTY PUMPS
Model Number: “A” “B” “C” “D”DAB05-AXXX-X-X 9-31/32" (253 mm) 8-5/32" (207 mm) 51-5/32" (1299 mm) 9-19/32" (243 mm)DAB05-PXXX-X-X 12-1/32" (306 mm) 8-3/32" (206 mm) 50-5/32" (1274 mm) --DAB05-SXXX-X-X 7-3/4" (197 mm) 8-3/32" (206 mm) 49-25/32" (1264 mm) --
For additional information contact technical support at (800)495-0276
NotesPro-Series Pumps
36
Specialty Diaphragm, Lubrication and Centrifugal PumpsPro-Series Pumps
3:1 Ratio Oil Grease CentrifugalModel Power Pump Packages Packages Pumps
Maximum Flow 24 9 7.5-lbs/min P237AX-EU=200 (757)GPM (LPM) (90.7) (34.1) (3.4-kg/min) P35AX-EU=230(870.5)
MaximumDischarge 300 750 7500 90Pressure (20.7) (51.7) (517) (6.1)
PSI (BAR)
Fluid Ports 1" (F) - In/Out Immersed Inlet Immersed Inlet Screened InletInlet/Outlet Control Handle Control Handle 2" Outlet
(BSP Available) Outlet Outlet 2-1/2" Outlet
Materials Stainless Carbon Steel Carbon Steel Cast Ironof Steel
Construction
Pump 94.7 (42.9) 44.7 (20.3) LP3001-1=30.7 (12) P237AX=48 (21.8)Weight P35AX=79 (36)
Lbs. (Kg.) LP3003-1=42.1 (19.1)
MaximumSolids 1/8 Clean Fluids Clean Fluids 1/4
Inches (mm) (3.2) (6.4)
Best PH10A-ASS-SST LP3100-1-B LP3001-1 P237A1-EUSelling PH10A-BSS-SST LP3101-1-B LP3003-1 P237A3-EUModels P35A1-EU(BSP
Available)
RecommendedFilter/ P29231-610 P29221-610 P29221-610 C284X3-810
Regulator (Filter-Regulator-Lubricator)
Air Line Kit 66073-1 66073-1 66073-1 66084-1
37
Specialty Pumps 3:1 Ratio High Pressure Diaphragm PumpPro-Series Pumps
High Pressure Diaphragm Pump Performance SpecificationsRatio: 3:1Maximum Flow: 24-g.p.m. (90.7-l.p.m.) Free Flow
12 (45.6) at 125-psi back pressureDisplacement per cycle: 0.06-Gallons (.23-Liters)Air Inlet: (Female) 3/8 - 18 N.P.T.F. - 1Fluid Inlet: 1 - 11-1/2 N.P.T.F. - 1
Rp 1 (1- 11 BSP parallel)Fluid Outlet: 1 - 11-1/2 N.P.T.F. - 1
Rp 1 (1- 11 BSP parallel)Max. operating pressure: 100-psi (6.9-bar)Suspended solids max. dia.: 1/8-in. (3.2-mm)Weight: lbs (kg) 94.73 (42.97)Maximum dry suction lift: 5 - 6-ft (1.5 - 1.8-m)
AccessoriesAir Line Filter-Regulator | P29231-610Piggyback unit features a 40 micron filter, metal bowl with sight glass and 0-125-psi gauge. Plumb directly to pump’s air inlet.
Service Repair Kits | Kit No. 637338 (air section)Kit No. 637339 (PH10X-XXX-XSX fluid section)Kit No. 637339-1 (PH10X-XXX-XHX fluid section)
Wall Mount Bracket | 67142Siphon tube then used to connect pump to fluid supply.*Please note pumps are not included with these kits.
Ordering Menu
PH10 A X S S XX T
BaseModel
1" Pump
CenterSection
A Aluminum
PortSize
A N.P.T.F. ThreadsB BSP Threads
WettedParts
S Stainless SteelHardware
S Stainless Steel
Seat/Ball CheckMaterial
HH 440 SS/ 440 SSSS 316 SS / 316 SS
DiaphragmMaterial
T PTFE (Teflon)
- -
38
Wall Mount Bracket67142
Specialty Pumps 3:1 Ratio High Pressure Diaphragm Pump Dimensions and Flow CurvesPro-Series Pumps
High Pressure Diaphragm Pump Dimensions and Flow Charts
Refer to www.irtools.com/aro/ for full size flow curves.
For additional information contact technical support at (800)495-0276
39
SPECIALTY PUMPS
LP310X-1-B Dimensions
Specialty Pumps - Oil PackagesPro-Series Pumps
Oil Package Performance SpecificationsRatio: 5:1Maximum Flow: GPM (LPM) 9 (34.1) Max. Working Flow: 6-g.p.m. (22.7-l.p.m.)Maximum Rec’d Cycles: 170 per minute LM2305A-31-BDisplacement per Cycle: 8.3-In3 (136-cm3)Air Inlet: (Female) 1/4 - 18 N.P.T.F. - 1Fluid Inlet: 1-1/2 - 11-1/2 N.P.T.F. - 1Fluid Outlet: 1/2 - 14 N.P.T.F. - 1Max. operating pressure: 150-psi (10.3-bar)Fluid Pressure Range: 0-750-psi (0-51.7-bar)Weight: lbs (kg) 44.7 (20.3)
LP3100-1-B Oil Package(Package does not include container)
AccessoriesAir Line Connection Kit* | Kit No. 66073-1Kit includes Piggyback Filter/Regulator with gauge, pipe nipple and a 5-foot section of air hose.
Service Repair Kits | Kit No. 637226 (Pump Rebuild Kit: Contains necessary soft parts to rebuild entire pump.)
*Please note pumps are not included with these kits.
Ordering Menu
LP310 X 1 B
ModelSeries
16-Gallon PortableGear Oil Package
MeterType
0 Pint1 Liter
- -
Major ComponentsItem: Description:Basic 5:1 Oil Pump: LM2305A-31-BDigital Meter: 635190-1 (Pint--LP3100-1-B)
635190-3 (Liter--LP3101-1-B)Drum Cover: 94421Material Hose: 623501-6Fluid Control Handle: 635391-1Dolly Assembly: 640058-2
Dimensions: Inches (mm)Model Number: “A”LP310X-1-B 45 (1143)
40
For additional information contact technical support at (800)495-0276
Specialty Pumps - Grease PackagesPro-Series Pumps
41
SPECIALTY PUMPS
LP3001-1 Dimensions
Grease Package Performance SpecificationsRatio: 50:1Maximum Delivery/Min.: 7.5-lbs. (3.4-kg)Maximum Rec’d Cycles: 135 per minute (LM2350E-X1-B)Displacement per Cycle: 0.875-In3 (14.33-cm3)Air Inlet: (Female) 1/4 - 18 N.P.T.F. - 1Material Inlet: ImmersedMaterial Outlet: 3/8 -18 N.P.T.F. - 1Max. operating pressure: 150-psi (10.3-bar)Max. fluid pressure: 7500-psi (517.2-bar)Weight: lbs (kg) 30.7 (12)
Ordering Menu
LP3001-1 Grease Packages(Packages do not include containers)
Dimensions: Inches (mm)Model Number: “A”LP3001-1 29 (737)
AccessoriesAir Line Connection Kit* | Kit No. 66073-1Kit includes Piggyback Filter/Regulator with gauge, pipe nipple and a 5-foot section of air hose.
Service Repair Kits | Kit No. 637227-B(Pump Rebuild Kit: Contains necessary soft parts to rebuild entire pump.)
*Please note pumps are not included with these kits.
LP3001-1 Major ComponentsItem: Description:Basic 50:1 Grease Pump: LM2350E-21-BHandle: 94334Drum Cover: 94420Follower Plate: 640095-2-BMaterial Hose: 624201-10Booster Grease Gun: 636103Z-Swivel: 636077
Model Series1 35-pound Grease Package
For additional information contact technical support at (800)495-0276
L P 3 0 0 X - 1
LP3003-1 Dimensions
Specialty Pumps - Grease PackagesPro-Series Pumps
Grease Package Performance SpecificationsRatio: 50:1Maximum Delivery/Min.: 7.5-lbs. (3.4-kg)Maximum Rec’d Cycles: 135 per minute (LM2350E-X1-B)Displacement per Cycle: 0.875-In3 (14.33-cm3)Air Inlet: (Female) 1/4 - 18 N.P.T.F. - 1Material Inlet: ImmersedMaterial Outlet: 3/8 -18 N.P.T.F. - 1Max. operating pressure: 150-psi (10.3-bar)Max. fluid pressure: 7500-psi (517.2-bar)Weight: lbs (kg) 42.1 (19.1)
Ordering Menu
LP3003-1 Grease Packages(Packages do not include containers)
Dimensions: Inches (mm)Model Number: “A” “B”LP3003-1 43 (1092) 40-1/8 (1019)
AccessoriesAir Line Connection Kit* | Kit No. 66073-1Kit includes Piggyback Filter/Regulator with gauge, pipe nipple and a 5-foot section of air hose.
Service Repair Kits | Kit No. 637227-B(Pump Rebuild Kit: Contains necessary soft parts to rebuild entire pump.)
*Please note pumps are not included with these kits.
LP3003-1 Major ComponentsItem: Description:Basic 50:1 Grease Pump: LM2350E-31-BDrum Cover: 94421Follower Plate: 640165Material Hose: 624201-10Booster Grease Gun: 636103Z-Swivel: 636077Dolly Assembly: 640057
Model Series3 20-pound Grease Package
42
For additional information contact technical support at (800)495-0276
LP300X - 1
Specialty Pumps - Centrifugal Pump ModelsPro-Series Pumps
43
SPECIALTY PUMPS
Centrifugal Pump Performance Specifications
Maximum Flow: GPM (LPM) 200 (757) P237AX-EU230 (870.5) P35AX-EU
Air Inlet: (Female) 3/4 -14 N.P.T. (P237AX-EU)1 - 11-1/2 N.P.T. (P35A1-EU)
Fluid Inlet: Screened InletFluid Outlet: 2" N.P.T.F. P35A1-EU
2-1/2" N.P.T.F. P237A1-EU2-1/2” BSP P237A3-EU
Max. operating pressure: 90-psi (6.2-bar)Air Consumption in CFM: P237AX-EU 100
P35A1-EU 160Suspended solids max. dia.: 1/4-inch (6.4-mm)Pump Housing Material: P237AX-EU Cast Iron
P35A1-EU Cast IronWeight: lbs (kg) P237AX-EU 48 (21.8)
P35A1-EU 79 (36)
Ordering Menus
P237A - X - EU
ModelSeries
200-GPM (757-LPM)
DischargeThread
1 2-1/2" N.P.T.3 2-1/2" BSP
AccessoriesAir Line Unit | C28453-810 for P237AX-EU
C28463-810 for P35A1-EUC284X3-810 models contain Filter, Regulator and Lubricator units.
Service Repair Kits | Repair parts are ordered individually.
Refer to Operator’s Manuals:P237AX-EU Pumps: Form P6856P35A1-EU Pumps: Form P7263
P35A - 1 - EU
ModelSeries
230-GPM (870-LPM)
DischargeThread
1 2" N.P.T.
Centrifugal Pump Dimensional Data and Flow Charts
For additional information contact technical support at (800)495-0276
Height: inches (mm) P237AX-EU 17-5/8 (448)P35A1-EU 22-1/2 (570)
Size of opening pump will pass through: inches (mm)P237AX-EU 8-3/4 (222) x 8-3/4 (222)P35A1-EU 8-7/16 (214) x 14-1/16 (357)
Discharge Pipe Tap: P237A1-EU 2-1/2" N.P.T.F.P237A3-EU 2-1/2" BSPP35A1-EU 2" N.P.T.F.
Air Inlet Pipe Tap: P237AX-EU 3/4" N.P.T.F.P35A1-EU 1" N.P.T.F.
Air Inlet Recommended Hose Size: inches (mm)P237AX-EU 3/4 (19)P35A1-EU 1 (25.4)
Exhaust Pipe Tap: P237AX-EU 1-1/4" N.P.T.F.P35A1-EU 1-1/4" N.P.T.F.
Exhaust Recommended Hose Size: inches (mm)P237AX-EU 1-1/4 (31.7)P35A1-EU 1-1/4 (31.7)
50
100
300
250
200
150
10
90
20
30
40
50
60
70
80
100 200 300 400 500 600 700 800 900 1000
0 40 80 120 160 200 240 280
Performance is at 90 psi (620 kPa)
DISCHARGE - U.S. GALLONS PER MINUTE
DISCHARGE - LITERS PER MINUTE
TOTA
L H
EAD
- FE
ET
TOTA
L H
EAD
- M
ETER
S
SERIES 35
SERIES 237
Accessories / Pulsation DampenersPro-Series Pumps
Pulsation DampenersDiaphragm and piston pumps of any type have at least two points intheir cycle where they provide no pressure or flow to a process.The unwanted result of this pressure fluctuation can often bematerial foaming, material pulsation, hydraulic shock or materialsplashing. While traditional pulsation dampeners can help reduceunwanted pulsation and other problems, they also require operatorintervention and adjustments.
Automatic Shock Blockers®� Automatic Air Adjustment - compensates for fluctuations in fluid
pressure without operator intervention.
� Significant Pulsation Reduction - the new Shock Blockers deliveran average 60% - 80% pulsation reduction in high back pressureapplications.
� Built for High-Flow/Aggressive Fluid Applications - the 2" modelscan handle up to 159 in.3 maximum fluid volume, and 3" modelsup to 509 in.2 maximum fluid volume.
� Broad Material Range for Compatibility - choose from PVDF,polypropylene, groundable acetal (1" models) or aluminum, castiron or stainless steel (2" & 3" models) body materials foroptimum pump-to-pulsation dampener compatibility.
� Broad Diaphragm/Bladder Fluid Compatibility - choose fromSantoprene, Nitrile, Teflon, Hytrel, Viton or Urethane foroptimum fluid-to-diaphragm compatibility.
� Perfect for Process Applications - pulsation reduction in longpiping runs helps prevent costly fluid pipe and downstream valvedamage.
� Bolted Construction - for leak-free vessel integrity and a saferwork-site.
� Ultra-Rugged Construction for Long Service Life - both insideand out, the new Shock Blockers are built tough to deliver worry-free, near pulse-free fluid handling.
Ordering Menu
SB 10 X X X X X
Model Series Blocker Size1-inch
Air BodyP Polypropylene
(Glass Filled)K PVDFD Conductive Acetal
ThreadA N.P.T.B BSP
FluidConstruction
P Polypropylene(Glass Filled)
K PVDFD Conductive Acetal
HardwareS Stainless Steel
(304)
DiaphragmA SantopreneC HytrelT PTFEU Urethane
- -
1" Port ModelsPulsation Dampener Type Non-Metallic / AutomaticMaterial See model description chartWeight Polypropylene 8.4 lbs (3.8 kgs)
Conductive Acetal 8.6 lbs (3.9 kgs)PVDF 9.0 lbs (4.1 kgs)
Material Inlet/Outlet (female) SB10X-AXX-X 1 - 11-1/2 N.P.T.SB10X-BXX-X Rp 1 (1-11 BSP parallel)
Air Inlet (male) Air Tamer is 3/8 - 18 N.P.T.Maximum Air Inlet Pressure 100-psi (6.9 bar)Maximum Material Inlet Pressure 100-psi (6.9 bar)Maximum Temperature Limits Polypropylene 35° - 150° F
(+1.6° - 66° C)Conductive Acetal 10° - 180° F (-12° - 82° C)PVDF 10° - 200° F (-12° - 93° C)
Maximum Fluid Volume 57 in.3 (934 cm3)
Notice: All possible options are shown in the chart above, however, certaincombinations may not be recommended. Consult a representative or thefactory if you have questions concerning availability.
44
Accessories / Pulsation DampenersPro-Series Pumps
2" Port ModelsPulsation Dampener Type Metallic / AutomaticMaterial See model description chartWeight Aluminum (fluid cap) 29 lbs (13.2 kgs)
Cast Iron (fluid cap) 70 lbs (31.8 kgs)Stainless St. (fluid cap) 71 lbs (32.2 kgs)
Material Inlet/Outlet SB20X-AXX-X 2 - 11-1/2 N.P.T.SB20X-BXX-XRp 2 (2-11 BSP parallel)
Air Inlet 3/4 - 14 N.P.T.Maximum Air Inlet Pressure 120-psi (8.3 bar)Maximum Material Inlet Pressure 120-psi (8.3 bar)Maximum Temperature Limits EPR -60° - 280° F (-51° - 138° C)
Nitrile 10° - 180° F (-12° - 82° C)Santoprene -40° - 225° F (-40° - 107° C)Teflon 40° - 225° F (4° - 107° C)Viton -40° - 350° F (-40° - 177° C)
Maximum Fluid Volume 159-In3 (2.61 lit.)
Ordering Menu
SB 20 X X X X X
Model Series Blocker Size2-inch
Air BodyA AluminumC Cast IronS Stainless Steel
ThreadA N.P.T.B BSP
FluidConstruction
A AluminumC Cast IronS Stainless Steel
HardwareS Stainless Steel
(304)P Plated Steel
DiaphragmA SantopreneG NitrileT PTFE (Teflon) /
SantopreneV Viton
- -
3" Port ModelsPulsation Dampener Type Metallic / AutomaticMaterial See model description chartWeight Aluminum (fluid cap) 41 lbs (18.6 kgs)
Cast Iron (fluid cap) 94 lbs (42.6 kgs)Stain. Steel (fluid cap) 96 lbs (43.5 kgs)
Material Inlet/Outlet SB30X-AXX-X 3 - 8 N.P.T.SB30X-BXX-X Rp 3 (3-11 BSP parallel)
Air Inlet 3/4 - 14 N.P.T.Maximum Air Inlet Pressure 120-psi (8.3 bar)Maximum Material Inlet Pressure 120-psi (8.3 bar)Maximum Temperature Limits EPR -60° - 280° F (-51° - 138° C)
Nitrile 10° - 180° F (-12° - 82° C)Santoprene -40° - 225° F (-40° - 107° C)Teflon 40° - 225° F (4° - 107° C)Viton -40° - 350° F (-40° - 177° C)
Maximum Fluid Volume 509 in.3 (8.34 lit.)
Ordering Menu
SB 30 X X X X X
Model Series Blocker Size3-inch
Air BodyA AluminumS Stainless Steel
ThreadA N.P.T.B BSP
FluidConstruction
A AluminumC Cast IronS Stainless Steel
HardwareS Stainless Steel
(304)P Plated Steel
DiaphragmA SantopreneG NitrileT PTFE (Teflon) /
SantopreneV Viton
- -
Notice: All possible options are shown in the chart above, however, certaincombinations may not be recommended. Consult a representative or thefactory if you have questions concerning availability.
Proper support of piping and pulsation dampener isrequired. Illustration for reference purposes only.
45
ACCESSORIES
Proper support of piping and pulsation dampener isrequired. Illustration for reference purposes only.
Accessories / Pulsation DampenersPro-Series Pumps
Pulsation Dampener Performance Charts
1/2" Pump w/SB1 % Reduction In Pulsation
20 94 . . . . . . . . . .81 . . . . . . . . . . . . . . . . .70 . . .6540 92 . . . . . . . . . . . . . . .83 . . . . . . . . . . . . . . . .7060 91 . . . . . . . . . . . . . . . . .85
1 2 3 4 5 10 12Fluid
Pressure
PSIBackPressure
Flow (GPM)
1" Pump w/SB1 % Reduction In Pulsation
20 90 . . . .80 . . .70 . . . . . . . . . . . . . . . . . . . . 6040 90 . . . . . . . . . .75 . . . . . . . . . . . . .7060 85 . . . . . . . . . .80 . . . . . . .7580 85 . . . . . . . . . . . . . . . . . . .80
1 5 10 15 20 25 30
Fluid
Pressure
PSIBackPressure
Flow (GPM)
1-1/2" Pump w/SB2 % Reduction In Pulsation
40 80 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7060 80 . . . . . . . . . . . . . . . . . . . . . . . .7080 80 . . . . . . . . . . . . . . . .65100 80 . . . . . .70
1 20 40 60 80
Fluid
Pressure
PSIBackPressure
Flow (GPM)
2" Pump w/SB2 % Reduction In Pulsation
40 65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5560 70 . . . . . . . . . . . . . . . . . . . . . . . .6080 70 . . . . . . . . . . . . . . . .55100 60 . . . . . .55
3 30 70 100 130
Fluid
Pressure
PSIBackPressure
Flow (GPM)
3"Pump w/SB3 % Reduction In Pulsation
40 60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5060 65 . . . . . . . . . . . . . . . . . . . . . . . .5580 60 . . . . . . . . . . . . . . . .50100 60 . . . . . .50
5 75 125 150 200
Fluid
Pressure
PSIBackPressure
Flow (GPM)
46
Diaphragm Pump AccessoriesPro-Series Pumps
Description
CYCLE SENSOR
Provides a closed contact outputfor monitoring pump operation.Can be used to moitor cycle rates,preventitive maintenance andrough flow rate indication. Powersupply and other devices requiredto gather, store or manipulatedata. (pump not included)
Order No. 67386 3/8" and 1/2"Non-Metallic Pumps (PD03-X & PD05-X)
67168 3/8" and 1/2"Non-Metallic Pumps (66605X-X)
67169 1", 1-1/2" and 2"Non-Metallic Pumps. 1" and 1-1/2" Metallic Pumps
67386 onPD05P-X-X-B
Description
COUNTDOWN BATCHER
Manual start batch counter kitcontrols the volume of fluiddispensed by controlling thenumber of pump cycles.(pump not included)
Order No. 67072 For 3/8", 1/2" and1" ported pumps
Description
CYCLE COUNTER KIT
Easy to install counter records upto 999,999 cycles. Kit includesnecessary installation hardware.For fluid inventory, preventativemaintenance and fluid metering.
Order No. 66975 for 3/8", 1/2", 1",1-1/2",2" and 3" ported pumps
47
ACCESSORIES
Description
EXHAUST THREADED MUFFLER KIT
Kit allows operator to pipe exhaustair away from application. Fitsonly non-metallic air motor section. 3/8” NPT exhaust port.(muffler not included)
Order No. 637438
Description
PE SERIES PUMPS WITH B0S SPECIALTY CODE
Replaces standard pump air valve.Operate pump with a remote four-way valve. Provides the ultimatecycle rate control for dosing andbatching applications.
Order No. PE0XX-XXX-XXX-B0SFor 3/8" and 1/2" PD0 Series(Remote valve not included in model.See below for four-way valve options.)
Description
PE SERIES PUMP CONTROL
ARO AlphaTM 4-way valve supplies air tocycle pump. Features bonded spool plus many actuator/return and solenoidoptions. (pump not included)
1/4" body ported. Actuator/Return options.Solenoid coil voltage options.
Order No.Model: Actuator/Return: Voltage:A212SD-120-A Solenoid/Solenoid 120-VACA212SS-120-A Solenoid/Spring 120-VACA212SD-012-D Solenoid/Solenoid 12-VDCA212SS-012-D Solenoid/Spring 12-VDCA212SD-024-D Solenoid/Solenoid 24-VDCA212SS-024-D Solenoid/Spring 24-VDCA212PS Pilot/SpringA212PD Pilot/Pilot
(Solenoid Valves require use of Connector,referenced on this page.)
Valve does notinclude connector,mufflers or fittings
Diaphragm Pump AccessoriesPro-Series Pumps
Description
AIR CONTROL ACTUATION VALVES
3-way valve controls air supply topump. Activation starts pump,deactviation cuts off air supply topump and exhausts air frommotor, which prevents stalling.
120 VAC Order No. MQ3728-120-A for 1/2"
and 1" pumps
H254SS-120-A for 1-1/2" pumps
MQ3729-120-A for 2" and 3" pumps
24 VDC Order No. MQ3728-024-D for 1/2"
and 1" pumps
H254SS-024-D for 1-1/2" pumps
MQ3729-024-D for 2" and 3" pumps
Description
CONNECTORS
Connects valve solenoid to PLC orother control device. Femaleconnector to male DIN of valvesolenoid.
Straight connector with 36" horizontalcable located on back.Order No. CBW
Straight connector with 36" verticalcable located on back.Order No. CHW
Description
DIAPHRAGM PUMP SPEED CONTROLS
Controls air volume supplied topump, thus permitting operator tocontrol speed of pump. Can bepanel mounted. Composite body.
Order No. 104104-N02 1/4" port size
104104-N04 1/2" port size
104104-N06 3/4" port size
MQ3728-120-A used on1/2” and 1” pumps
67161-2 Mini BatchCounter with 1" pump
Description
SOLENOID ACTUATION KIT
Control pump cycle rate withon/off signal from PLC or otherdevice. Kit includes connectorw/36" cable plus components andinstructions to install on standardpump. For dosing and batchingapplications.
Order No. 67165-1 (24VDC) for 3/8"and 1/2" ported pumps
67165-2 (120VAC) for 3/8"and 1/2" ported pumps
67166-1 (24VDC) for 1", 1-1/2" and 2" non-metallic and1", 1-1/2" metallic pumps (less3:1 models)
67166-2 (120VAC) for 1", 1-1/2" and 2" non-metallic and1", 1-1/2" metallic pumps (less3:1 models)
CBW
CHW
Description
MINI BATCH COUNTER
For simple batching applications.Used with cycle counter or flowmeter to control fluid output frompump.
Order No. 67161-2
Description
PNEUMATIC LIQUID LEVEL SENSORS
Used to control pump.
Order No 59916-1 to sense when fluid exceeds a desired level
59916-2 to sense when fluidfalls below a desired level
Description
SCREENED INLET KITS
Converts standard pump for usein a sump. Prevents unwanteddebris from entering pump’s fluidinlet.
Order No 67174-15 for use with 1-1/2" metallic pumps
67174-20 for use with 2" metallic pumps
48
Solenoid valve requires use of connector. See below for connector information.
Diaphragm Pump AccessoriesPro-Series Pumps
49
ACCESSORIES
Description
WALL MOUNT
Conveniently mount pump abovecontainer. Made of of heavy gagecoated steel.(pump not included)
Order No. 67388* 3/8" Pumps
76763* 1/2" Pumps
66100* 1" Metallic Pumps
62133 1-1/2" Metallic Pumps
67142 1" 3:1 High Pressure Pumps
*(does not include mounting hardware)
Description
DRUM COVERS
Keeps debris from entering fluid supply. Accommodatesdiaphragm pump. Fits 5-gallon and 55-galloncontainers.
Order No. 67055-B Stainless Steel, for 1/4" Pumps on 5-gal.containers
66971 Stainless Steel, for 1/2" Pumps on 5-gal. containers
Description
PNEUMATIC MATERIAL AGITATORS
Prevents fluid from separating.Mounts in opening on 5-gallon or55-gallon drum covers.
Order No. 651100 5-Gallon containers,use with 651851 and 66971drum covers
651103 55-Gallon drums, usewith 66087 drum side-mountadapter. Use with 66197 or67141 drum covers requires75704 mount (3), Y8-58-Cscrews and (3) Y12-5-C nuts
Description
SIPHON TUBE
Used to draw fluid from 55-gallondrums. Straight tube when pumpis mounted on drum; angle tubewhen pump is wall mounted abovecontainer. Plastic (PVC, PP,PTFE), Carbon Steel (CS) or 316Stainless (SS)Order No. 61412 Straight N.P.T. (male)
PVD for 1/2" Pumps
65109 CS N.P.T. (female) for 1" Pumps
66779 PVC 36" N.P.T. (female)for 1" Pumps
66779-1 PVC, N.P.T. (female) 14.875" L for 1" pumps used with275-gallon bulk tank
66779-2 PVC, N.P.T. (female) 49" L for 1" pumps used with275-gallon bulk tank
66779-3 PVC, N.P.T. (female) 61" L for 1" pumps used withlarge bulk tanks
76763 Wall Mount 651100 Agitator
65109 Siphon Tube
Piston Pump AccessoriesPro-Series Pumps
50
Description
WALL MOUNTS
Permits pump to be mountednear fluid containers. For usewith stub style 2:1 and 4:1 ratiopumps.
Order No. 61113 for N-Series air motor stub pumps fitted with bungadapters.
Description
MUFFLER
Reduces noise level of airexhaust to acceptable OSHAstandards.
Order No. 61879 for use with 612041-X models.
Description
WET-SOL “PLUS”
Designed to prolong packing lifeby keeping piston rod andpackings wetted.
Order No. 66333-B Quart for NM2202X-X and NM2304X-Xpumps
66334-B Gallon for NM2202X-X and NM2304X-Xpumps
Description
AIR LINE LUBRICANT
Used in air line lubricator to airmotor. High quality “EP” extremepressure gear oil. Non-detergent,rust or oxidation inhibited.Viscosity of 700 to 1000 S.U.S. at100° F.
Order No. 62274 one quart bottle
Description
OVER-RUN CONTROL
Shuts off pump when excessivecycling occurs due to empty fluidsupply container.
Order No. 635040 for 1/2" and 1" porteddiaphragm pumps for 1:1, 2:1and 4:1 ratio piston pumps
23644-400 for 1-1/2" and 2" ported diaphragm pumps
635043 for 3" ported diaphragm pumps
Description
DRUM COVERS
Keeps debris from entering fluidsupply. Accommodates siphonhose and agitator. Fits 5-galloncontainers.
Order No. 651851 Carbon Steel, for 2"and 3" air motor pumps
94422 Carbon Steel, 2" bung opening for 55-gal. containers
651851 Drum Cover
94422 Drum Cover
Viscosity Conversion ChartPro-Series Pumps
51
Viscosity Conversion ChartSaybolt
Centi Universal Saybolt Ford Ford Zahn Zahn Zahn
Poise Poise (SSU) Furol No. 3 No. 4 No. 1 No. 2 No. 3
1 .01 312 .02 344 .04 387 .07 47 810 .10 60 9 5 30 1615 .15 80 13 10 8 34 1720 .20 100 15 12 10 37 1825 .24 130 17 15 12 41 1930 .30 160 19 19 14 44 2040 .40 210 24 25 18 52 2250 .50 260 29 29 22 60 2460 .60 320 34 33 25 68 2770 .70 370 39 36 28 72 3080 .80 430 42 41 31 81 3490 .90 480 49 45 32 88 37 10100 1.0 530 54 50 34 41 12120 1.2 580 59 58 41 49 14140 1.4 690 70 66 45 58 16160 1.6 790 79 72 50 66 18180 1.8 900 91 81 54 74 20200 2.0 1000 100 90 58 82 23220 2.2 1100 110 98 62 88 25240 2.4 1200 120 106 65 27260 2.6 1280 128 115 68 30280 2.8 1380 138 122 70 32300 3.0 1475 148 130 74 34320 3.2 1530 153 136 89 36340 3.4 1630 163 142 95 39360 3.6 1730 173 150 100 41380 3.8 1850 185 160 106 43400 4.0 1950 195 170 112 46420 4.2 2050 205 180 118 48440 4.4 2160 216 188 124 50460 4.6 2270 227 200 130 52480 4.8 2380 238 210 137 54500 5.0 2480 248 218 143 58550 5.5 2660 266 230 153 64600 6.0 2900 290 250 170 68700 7.0 3380 338 295 194 76800 8.0 3880 388 340 223900 9.0 4300 430 365 2471000 10.0 4600 460 390 2641100 11 5200 520 445 2991200 12 5620 562 480 3231300 13 6100 610 520 3501400 14 6480 648 550 3721500 15 7000 700 595 4001600 16 7500 750 635 4301700 17 8000 800 680 4601800 18 8500 850 720 4901900 19 9000 900 760 5202000 20 9400 940 800 5402100 21 9850 985 835 5652200 22 10300 1030 875 5922300 23 10750 1075 910 6172400 24 11200 1120 950 6452500 25 11600 1160 985 6763000 30 14500 1450 1230 8333500 35 16500 1650 1400 9504000 40 18500 1850 1570 10604500 45 21000 2100 1780 11755000 50 23500 2350 13505500 55 26000 2600 14956000 60 28000 2800 16056500 65 30000 3000 17207000 70 32500 3250 18707500 75 35000 3500 20108000 80 37000 3700 21208500 85 39500 3950 22709000 90 41000 4100 23609500 95 43000 4350 247010000 100 46500 4650 267015000 150 69400 694020000 200 92500 925030000 300 138600 1386040000 400 185000 1850050000 500 231000 2310060000 600 277500 2775070000 700 323500 3235080000 800 370000 3700090000 900 415500 41550100000 1000 462000 46200125000 1250 578000 57800150000 1500 694000 69400175000 1750 810000 81000200000 2000 925000 92500
ACCESSORIES
Pump Airborne Noise EmissionsPro-Series Pumps
52
Pump Airborne Noise Emissions
Pump Air Operating SoundPort Size Pressure Cycles/ Pressure(Inches) (PSI) Minute (LAeq)
Diaphragm Pumps
1/2 70 60 75.0 db(A)
1 70 60 79.7 db(A)80.6 db(A)
1-1/2 70 60 81.0 db(A)82.8 db(A)
2 70 60 *85.0 db(A)
3 70 50 *83.0 db(A)
The pump sound pressure levels published below have beenupdated to an Equivalent Continuous Sound Level (LAeq) to meetthe intent of ANSI S1.13-1971. CAGI-PNEUROP S5.1 using fourmicrophone locations.
FORM 0604-P 1006 © 2006 Ingersoll Rand Company
CPN 15260870
Ingersoll Rand Industrial Technologies provides products, services, and solutions to enhance theefficiency and productivity of our commercial, industrial, and process customers. Our innovativeproducts include air compressors, air systems components, tools, pumps, material and fluidhandling systems and microturbines.
www.irtools.com/aro
ARO Diaphragm Pumps are backed by a5-year warranty on materials andworkmanship for your purchasing peaceof mind.
ARO’s Pump design and manufacturingoperations have demonstrated compliancewith the quality process, health and safety,technical file and multi-lingual standardsset forth by the FEM (Federation Europeenede la Manutention) for the European Union(Communitie Economique).