practice 1 ccna

8/10/2019 Practice 1 ccna

1/30

CCNA 640-607 Practice Exam Two

At the console terminal, you typeRouter#show interface serial 1

You receive the following as part of the output:Serial1 is up, line protocol is down

What could cause this? hoose four!

A! "here are no eepalives$! "here is no cloc rate! "here is a wrong connector%! &n a 'ac(to('ac connection, the other end of the connection is

administratively down)! "he ca'le is disconnected

Answer: A, $, , and %

&f the ca'le were physically disconnected, then it would show Serial1 isdown, line protocol is down! When Serial1 is up, line protocol is down,it points to a layer * pro'lem which could 'e no eepalives, no clocrate, wrong connector, or in a 'ac(to('ac connection, the other end ofthe connection is administratively down! &f Serial1 is administratively

down +line protocol is down then the administrator manually disa'ledthe interface!

Router interfaces are generally configured 'y the command:Router+config#interface type num'er

Which routers need more information for configuration?

A! -or isco .///, .*//, and .0// series, define the interface 'y slot, port num'er adapter, and port$! -or isco /// series, define the interface 'y slot, port adapters, and port num'ers! -or isco *0// series, define the interface 'y slot and port num'er%! "here are no routers that need additional information, all come with the e2act feature set and will respond e2actly the same

Answer: A

isco .///, .*//, and .0// series routers have cards called 3ersatile&nterface 4rocessors +3&4s! "hese cards can have one or two slots for

each port adapter! )ach port adapter can have a num'er of interfaces!"he num'ering synta2 is as follows:type slot/port number adapter/port!

1

Copyright 2000 2002 CCxx Productions. All rights reserved. Do not duplicate orredistribute in any form.


2/30


You have typed in 5ena'le password isco5 at the glo'al configurationprompt! What did this command accomplish?

A! &t sets 5isco5 as the password to the privileged )6) mode$! &t sets 5isco5 as the password for any incoming "elnet sessions! &t sets 5isco5 as the password for the console terminal%! &t sets 5isco5 the password for all access

Answer: A

"his command sets 5isco5 as the password to the privileged )6) mode!

You are woring with a router, release 1/!78, what command loads aconfiguration file from a "-"4 server directly into 93RA?

A! configure terminal$! copy tftp running(config! copy tftp startup(config%! configure overwrite

Answer:

"o load a configuration file from a "-"4 server directly into 93RA, usethe following command: copy tftp startup(config! "he startupconfiguration file is stored in 93RA!

Which command+s display the 'acup configuration file that is stored in93RA? hoose two!

A! show startup(config$! show config! show running(config%! write term

Answer: A and $

"he commands ;show startup(config< +&=S 1/!78 and ;show config< +&=S

1/!* and earlier show the 'acup configuration file! "he commands;show running(config< +&=S 1/!78 and ;write term< +&=S 1/!* andearlier show the active configuration parameters!

2



3/30


What will the 5show version5 command display? hoose four!

A! system hardware$! software version! names and location of the configuration files%! 'oot images)! configuration parameters

Answer: A, $, , and %

"he ;show version< command will display the system hardware, softwareversion, names and location of the configuration files, and 'oot images!"o see the configuration parameters, you need to use the command ;showrunning(config< +&=S 1/!78 or ;write term< +&=S 1/!* and earlier!

Which commands will display the active configuration parameters? hoosetwo!

A! show running(config$! write term! show version%! display term

Answer: A and $

&=S Release 1/!* or earlier uses ;write term"he ma2imum num'er of commands that a router can save in its history is>>>>>>>?

A! 1/$! *0! 1*@%! */

Answer: $

se the terminal history siBe or history siBe to set the num'er ofcommands that are saved! "he default is 1/ and the ma2imum is *0! "ype5terminal history siBe *05 +or however many lines you want toremem'er! "o see how many commands are remem'ered use 5show history5!

3



4/30


A isco router provides many editing shortcuts! Which shortcut wouldyou use to move to the 'eginning of a line?

A! trl()$! )sc($! trl(A%! trl(-

Answer:

Some of the editing commands are as follows:trl(A move to 'eginning of linetrl() move to end of line)sc($ move to 'eginning of previous wordtrl(- move forward one charactertrl($ move 'ac one character)sc(- move forward one word

Which com'ination of eys will allow you to view the previous commandsthat you typed at the router?

A! trl(4$! )S(4! Shift(4%! Alt(4

Answer: A

trl plus a ey, moves either one character or one line! )S moves oneword! "he com'inations are:trl(A move to 'eginning of linetrl() move to end of linetrl(- move forward one charactertrl(4 previous command recalltrl(9 more recent command recalltrl($ move 'ac one character)sc($ move to 'eginning of previous word)sc(- move forward one word

"A$ gives you entry completion!

4



5/30


When you first log into a router, you will 'e in user )6) mode! "herouter waits for 1/ minutes for input! You have decided that you wantthe router to not wait for input! Which command would you use?

A! e2ec(timeout /$! no e2ec(timeout /! set timeout off%! set timeout route

Answer: $

=n a isco router, most commands can 'e cancelled 'y typing a ;no

practice 1 ccna

Documents