(2) With the Customer Projects screen visible, (2) With the Customer Projects screen visible, click on the Customers click on the Customers AddAdd button. Following button. Following this, a set of Customer and project information this, a set of Customer and project information screens will automatically open , one after the screens will automatically open , one after the other, until at least the minimum Customer Project other, until at least the minimum Customer Project information (Boxes with Red backgrounds) has information (Boxes with Red backgrounds) has been entered. Click Save when finishing each been entered. Click Save when finishing each screen.screen.

If an air audit checklist was completed while at the If an air audit checklist was completed while at the plant, use it to complete these forms. plant, use it to complete these forms.

(1)

(2)

(3)

(4)

Click Add to define the project compressed air system

(5)Be sure to enter a life cycle value.

Populate with known system requirements; define the sight conditions and utility rate. Library values are available. Make sure all pink fields are populated. Click Save.

Select the Systems tab

(6)

(7)

(8)

Click Add to define the system compressor/s

(9)Get from Library, Copy from Project, or create from scratch. Load in annual maintenance costs. Repeat as needed to define the system. Click Save.

Once the initial project system and related compressor/s are defined, a report can be generated that shows the annual operational cost for that system.

What to do with the information

1. Copy the Existing System within the same project and rename it as desired.

2. Replace the project compressors with the desired alternative in the new system. Add any purchase/installation costs and annual maintenance numbers. System parameters may be altered to reflect demand or supply side energy efficiency measures.

3. Duplicate this process to include any competitve solutions.

4. The detailed report will now provide an imperical comparison on a cost basis for each system and their related cost savings/payback.

Making System Comparisons

By creating alternate systems, a comparison report can be generated between systems to demonstrate cost savings to be realized and the payback time for implementing the alternate systems. Graphical representations of these savings are also available.

What to do with the information

Part 2 – Training Manual – How to use System Wizard 3

This program has 7 functions from which to choose.This program has 7 functions from which to choose.Each function will have different pages for entering the Each function will have different pages for entering the data that will be used to compare different systems; such data that will be used to compare different systems; such as compressors within each system, shift hours, energy as compressors within each system, shift hours, energy costs, etc.costs, etc.

Versions 3.50 and higher displays the number of days until the Versions 3.50 and higher displays the number of days until the current license expired. An updated license can be downloaded current license expired. An updated license can be downloaded from Sullinet.from Sullinet.

The “EXIT” button will cause the program to shut down and willThe “EXIT” button will cause the program to shut down and willexit the user from the program. This is done by clicking on the exit the user from the program. This is done by clicking on the ““EXIT” button.EXIT” button.

The “CUSTOMER PROJECTS” button is where all the data on the The “CUSTOMER PROJECTS” button is where all the data on the systems being compared, compressors, shift hours, etc., is filled in.systems being compared, compressors, shift hours, etc., is filled in.To enter these pages, click on the button.To enter these pages, click on the button.

Clicking on the Clicking on the “CUSTOMER “CUSTOMER PROJECTS” button PROJECTS” button opens the SystemWizard opens the SystemWizard dashboard.dashboard.

As can be seen, the As can be seen, the SystemWizard SystemWizard Dashboard contains 4 Dashboard contains 4 tabs:tabs:

The “Customer Projects”The “Customer Projects”tab has three sectionstab has three sections

Each section has a row Each section has a row of buttons which help of buttons which help the user to, copy, edit, the user to, copy, edit, delete, filter and sort delete, filter and sort through the data found through the data found in each section.in each section.

To add a customer, To add a customer, click on the “ADD” click on the “ADD” button.button.

Doing so, will open a new Doing so, will open a new window called “Add window called “Add Customer” as shown.Customer” as shown.

Through out the new program, the user will Through out the new program, the user will notice that some fields are high lighted in notice that some fields are high lighted in RED with an asterisk. These fields must RED with an asterisk. These fields must contain data before the user can save the contain data before the user can save the information. The program will not allow information. The program will not allow the user to proceed until that particular field the user to proceed until that particular field is filled in. Other fields may be left blank.is filled in. Other fields may be left blank.

Once all important Once all important information is filled in, the information is filled in, the user can click on the user can click on the “SAVE” button to save the “SAVE” button to save the information and a window information and a window for entering contact for entering contact information will open.information will open.

In this window you are asked to enter a Project Name, verify the project-specific engineering units, and any other desired project-specific information. At a minimum, assign a project name. Click Save to continue

To delete a customer, the To delete a customer, the user must click on the gray user must click on the gray button in front of the button in front of the customer information that is customer information that is going to be deleted; then going to be deleted; then click on the DELETE buttonclick on the DELETE button

To “COPY” a customer, To “COPY” a customer, click on the gray button in click on the gray button in front of the row with the front of the row with the information of the customer information of the customer that the user wants to copy. that the user wants to copy.

Click on the “COPY” button Click on the “COPY” button and a new pop up window and a new pop up window will appear. will appear.

The copied customer The copied customer information appears in this information appears in this window. The user can window. The user can modify the information and modify the information and than save the changes by than save the changes by clicking the SAVE button.clicking the SAVE button.

If the user saved the changes, If the user saved the changes, a new row will appear under a new row will appear under the CUSTOMERS section the CUSTOMERS section with the copied customer as with the copied customer as shown above.shown above.

Click on the “EDIT” button Click on the “EDIT” button after making sure you have after making sure you have selected the desired project. selected the desired project.

And the “EDIT CUSTOMER” And the “EDIT CUSTOMER” page will open up for the page will open up for the customer chosen. User will customer chosen. User will make the changes and click make the changes and click “SAVE” to close the window, “SAVE” to close the window, save the information and return save the information and return to the SystemWizard to the SystemWizard Dashboard.Dashboard.

To add a contact under a To add a contact under a customer, click on the gray customer, click on the gray button to choose a customer button to choose a customer

Next click on the “ADD” Next click on the “ADD” button under the contact button under the contact section. section.

This will open a new pop up This will open a new pop up window called “ADD window called “ADD CONTACT” shown above. CONTACT” shown above.

To add a project under a To add a project under a customer, click on the gray customer, click on the gray button to choose a customer.button to choose a customer.

Then click ADD in the Then click ADD in the Projects section. Projects section.

When the Add button is used, the user is moved to this pageWhen the Add button is used, the user is moved to this pagewithin the program. As can be seen, now we are entering the within the program. As can be seen, now we are entering the data on the project. The only required field is the project name.data on the project. The only required field is the project name.

New FeatureNew Feature: If the project is at the same locations as the : If the project is at the same locations as the customer, the user can use the GET CUSTOMER button to bring customer, the user can use the GET CUSTOMER button to bring in the address given to the customer. in the address given to the customer.

When the GET CUSTOMER button is used, the program When the GET CUSTOMER button is used, the program will open this window. The user can select the properwill open this window. The user can select the propercustomer for this project and click SELECT. customer for this project and click SELECT.

It will cause the previous window to close and return the It will cause the previous window to close and return the user to this screen. As can be seen, the chosen customer’suser to this screen. As can be seen, the chosen customer’saddress information was brought into this page. address information was brought into this page.

It also can allow the user to make changes to the units beingIt also can allow the user to make changes to the units beingused by the program for report generation. used by the program for report generation.

Click on the LIBRARIES tab to enter the three libraries containedClick on the LIBRARIES tab to enter the three libraries containedin the program; compressors, sites, and utilities.in the program; compressors, sites, and utilities.

Doing so will open up this new window. On this page there areDoing so will open up this new window. On this page there arethree tabs which contain pre-determined information for the threethree tabs which contain pre-determined information for the threelibraries. The three libraries are, Compressors, Sites and Utilities. libraries. The three libraries are, Compressors, Sites and Utilities. These are the same libraries that were accessed when entering the These are the same libraries that were accessed when entering the system data. Let us now look at the Compressor library.system data. Let us now look at the Compressor library.

LIB2

As can be seen, the compressor library comes with pre-defined As can be seen, the compressor library comes with pre-defined compressors. This data can not be deleted or modified. The compressors. This data can not be deleted or modified. The library contains the current data for all Sullair compressorslibrary contains the current data for all Sullair compressors ..

LIB3

It also contains some generic compressors commonly foundIt also contains some generic compressors commonly foundout in the field.out in the field.

LIB4

The filters at the top of the page allow the user to narrow down The filters at the top of the page allow the user to narrow down the choices for the type of compressor that will be used in the the choices for the type of compressor that will be used in the program.program.

LIB5

The Favorites Checkbox at the top of the page allow the user The Favorites Checkbox at the top of the page allow the user narrow the search to only models he/she has previously narrow the search to only models he/she has previously marked as Favorites.marked as Favorites.

The user also has all of the common functions found in theThe user also has all of the common functions found in theprogram to be able to copy, add view, clear filter and sorts asprogram to be able to copy, add view, clear filter and sorts asshown previous in this presentation.shown previous in this presentation.

LIB6

To view the data of a particular compressor, the user mustTo view the data of a particular compressor, the user mustfirst click on the grey button in front of the row which first click on the grey button in front of the row which contains the compressor information. This will cause the entire contains the compressor information. This will cause the entire row of information to become highlightedrow of information to become highlighted.

LIB7

Next click the View button and a new window will open upNext click the View button and a new window will open upthat will display the compressor data as shown in the following that will display the compressor data as shown in the following page. page.

LIB8

Here is the new window displaying the chosen compressors data.Here is the new window displaying the chosen compressors data.This data can not be modified. To make changes, the user needs This data can not be modified. To make changes, the user needs to use the Copy button above. This will open up the following page.to use the Copy button above. This will open up the following page.

LIB9

Now the user can make changes to the data of this compressor.Now the user can make changes to the data of this compressor.The program will not allow the user to save the modified dataThe program will not allow the user to save the modified dataunder the same name, therefore, the user must change the nameunder the same name, therefore, the user must change the nameof this compressor in order to save the modified data.of this compressor in order to save the modified data.

LIB10

This is the warning the user will obtain if trying to save the This is the warning the user will obtain if trying to save the modified data using the same model name for this compressor.modified data using the same model name for this compressor.

LIB11

Once a new model name has been given to the compressor, the Once a new model name has been given to the compressor, the user can than save the data by using the Save button above.user can than save the data by using the Save button above.

LIB12

A new filtering function is also available that allows the user to define his/her favorite models from the entire database. Merely check mark the Favorites box on this screen to add it to the Favorites list. This feature exists in all three libraries.

A new model can also be created by selecting Copy from the A new model can also be created by selecting Copy from the main compressor library screen. The same method would apply main compressor library screen. The same method would apply as previously stated. as previously stated.

LIB13

As can be seen below, the modified compressor was saved to As can be seen below, the modified compressor was saved to the compressor library and can be used on future projects.the compressor library and can be used on future projects.

LIB14

Note: Any compressor that was added by the user can be Note: Any compressor that was added by the user can be modified or deleted from the library.modified or deleted from the library.

To ADD a compressor to the library, click on the ADD buttonTo ADD a compressor to the library, click on the ADD buttonabove. This will open a new window as follows.above. This will open a new window as follows.

LIB15

When the ADD button is used, the user must fill in all of the When the ADD button is used, the user must fill in all of the data fields manually. Once all fields are filled, the user can data fields manually. Once all fields are filled, the user can use the save button to save the newly created compressor into the use the save button to save the newly created compressor into the library for future use. Or the user can exit and return to the previous library for future use. Or the user can exit and return to the previous page by using the Cancel button.page by using the Cancel button.

LIB16

Remember that only user-added information can be deleted from Remember that only user-added information can be deleted from the libraries.the libraries.

LIB17

To Delete a compressor from the library, select the compressorTo Delete a compressor from the library, select the compressorto be deleted by clicking on the grey button in front of the rowto be deleted by clicking on the grey button in front of the rowthat contains the information. This will cause the entire row to that contains the information. This will cause the entire row to become highlighted as shown below.become highlighted as shown below.

LIB18

Click the Delete button above and the user will get this warningClick the Delete button above and the user will get this warningmessage. Click on the YES to proceed, this will cause the row message. Click on the YES to proceed, this will cause the row containing the information to be removed from the library as containing the information to be removed from the library as shown on the following page.shown on the following page.

LIB19

As shown, row 1182 was deleted from the library.As shown, row 1182 was deleted from the library.

LIB20

This page also contains the Clear filter and Clear Sort functionsThis page also contains the Clear filter and Clear Sort functionsas previously discussed in this presentation.as previously discussed in this presentation.

LIB21

The Site tab of the library section contains all of the functions The Site tab of the library section contains all of the functions found in the compressor tab and work exactly the same as found in the compressor tab and work exactly the same as previously mentioned.previously mentioned.

LIB22

The Site library contains Pre-defined major cities within the The Site library contains Pre-defined major cities within the Unites States and a few international locations. Unites States and a few international locations. The Site library also contains the same filter functions as other The Site library also contains the same filter functions as other sections of the program to allow the user to narrow down the sections of the program to allow the user to narrow down the choices to be used.choices to be used.

LIB23

Editing, copying, deleting and saving data follow the sameEditing, copying, deleting and saving data follow the sameprocess as outlined in the compressor tab of the libraries.process as outlined in the compressor tab of the libraries.

LIB24

The Utilities Tab of the library section contains data on The Utilities Tab of the library section contains data on common rates found within the United States. common rates found within the United States. This Tab contains the same functions as the two This Tab contains the same functions as the two previous tabs and function the same way. This is an previous tabs and function the same way. This is an excellent place to use the Favorites selection.excellent place to use the Favorites selection.

LIB25

All three tabs also contain a special function called Favorites.All three tabs also contain a special function called Favorites.

LIB26

For each library, the user can select the Favorites box when For each library, the user can select the Favorites box when selecting, modifying or up dating compressor, site and selecting, modifying or up dating compressor, site and utility data.utility data.

By doing so, the user can than check the Favorites box By doing so, the user can than check the Favorites box displayed at the top of each tab for compressor, Site and displayed at the top of each tab for compressor, Site and utilities and the program will only display the data for the utilities and the program will only display the data for the three libraries which have the favorites checked thus three libraries which have the favorites checked thus narrowing the field of information being displayed in the narrowing the field of information being displayed in the three tabs.three tabs.

Clicking the “CALCULATIONS” button opens the Clicking the “CALCULATIONS” button opens the Calculations Window for adding project specific formulas.Calculations Window for adding project specific formulas.

To begin using the Calculators, the user will click To begin using the Calculators, the user will click on the Add button above.on the Add button above.

CAL3

Doing so will open this new window.Doing so will open this new window.

A list will be displayed of all of the types of A list will be displayed of all of the types of calculations the program can complete . Use the calculations the program can complete . Use the scroll bar on the right hand side to view all scroll bar on the right hand side to view all calculations.calculations.

CAL5

Doing so will open this new window. NextDoing so will open this new window. Nextclick on the drop down arrow of the Selectclick on the drop down arrow of the SelectCalculation Type field.Calculation Type field.

Highlight the calculation you want the program Highlight the calculation you want the program to complete as shown above and double click .to complete as shown above and double click .

CAL6

This will open a window that displays all of the inputs This will open a window that displays all of the inputs required by the program to be able to complete the required by the program to be able to complete the chosen calculation.chosen calculation.Once again, only the highlighted boxes need to be filled.Once again, only the highlighted boxes need to be filled.

CAL8

Once these fields are completed, the user will click on the Once these fields are completed, the user will click on the Calculate button above and the program will complete the Calculate button above and the program will complete the calculation.calculation.

CAL12

The calculated parameters will appear in the areaThe calculated parameters will appear in the areacircled.circled.

CAL13

If a calculation requires Ambient data, the user can click If a calculation requires Ambient data, the user can click on the Ambient button above to retrieve the required data .on the Ambient button above to retrieve the required data .

CAL14

Clicking the Ambient button, takes the user to the Site LibraryClicking the Ambient button, takes the user to the Site Librarywhere the ambient data of a particular location can be obtained. where the ambient data of a particular location can be obtained. The program will than use that data to complete the calculation.The program will than use that data to complete the calculation.

The Site library is used in the same fashion as discussed previouslyThe Site library is used in the same fashion as discussed previouslyin this presentation. Once a location has been chosen, the program in this presentation. Once a location has been chosen, the program will close this window and return the user to the previous pagewill close this window and return the user to the previous pagethat follows.that follows.

CAL15

The user can continue with the calculation as previously discussed.The user can continue with the calculation as previously discussed.

Once the calculation is complete, it can be saved by using the Once the calculation is complete, it can be saved by using the Save button above.Save button above.

Doing so will save the calculation in the program asDoing so will save the calculation in the program asshown above. The description, category, name, input andshown above. The description, category, name, input andoutput of the calculation will be displayed.output of the calculation will be displayed.

If the user does not want to save the calculation, the cancel buttonIf the user does not want to save the calculation, the cancel buttoncan be used to close this window and return to the opening page can be used to close this window and return to the opening page of the calculations.of the calculations.

To Exit the calculations, click on the Exit button above andTo Exit the calculations, click on the Exit button above andthe program will return the user to the following page.the program will return the user to the following page.

As the name implies, the CONTROLS COMPARISON tab is As the name implies, the CONTROLS COMPARISON tab is used to allow the user to demonstrate to a customer the used to allow the user to demonstrate to a customer the differences in using different Compressor control schemes to differences in using different Compressor control schemes to help improve the compressor equipment efficiency based on help improve the compressor equipment efficiency based on industry standard CAGI curves.industry standard CAGI curves.

Clicking the button will open this window. The first steps is to Clicking the button will open this window. The first steps is to input data about the system and compressor.input data about the system and compressor.

CC5

System Capacity: This is the volume that the system holds in System Capacity: This is the volume that the system holds in piping and or receiver tanks.piping and or receiver tanks.

CC6

To input data into these fields, click inside the field box and To input data into these fields, click inside the field box and type in the data. In this example, we are putting 500 as the type in the data. In this example, we are putting 500 as the system capacity.system capacity.

CC7

Nominal Power: This is the horse power of the compressor we Nominal Power: This is the horse power of the compressor we are using. For our example, it will be a 100 horse.are using. For our example, it will be a 100 horse.

CC8

Rated Flow: This is the compressor full rated flow. For our Rated Flow: This is the compressor full rated flow. For our example we will make it be 460 ACFMexample we will make it be 460 ACFM

CC9

Rated Pressure: The compressors full load pressure rating. For Rated Pressure: The compressors full load pressure rating. For our example it will be 110 PSI.our example it will be 110 PSI.

CC10

We will leave the load delta at 10 PSI. The program defaults We will leave the load delta at 10 PSI. The program defaults the Unload power at 25% of the Nominal power entered on the Unload power at 25% of the Nominal power entered on this sheet, but it can be adjusted if need be by click inside the this sheet, but it can be adjusted if need be by click inside the fields and inputting the proper data.fields and inputting the proper data.

CC11

We have now set the parameters for the compressor we want We have now set the parameters for the compressor we want to be using, next we can pick what types of controls we want to be using, next we can pick what types of controls we want to use with this compressor. This can be done using the circled to use with this compressor. This can be done using the circled fields above.fields above.CC12

First we need to pick the compressor type we want to use. First we need to pick the compressor type we want to use. This is done using the circled fields above. For our example, This is done using the circled fields above. For our example, let’s use the following; lubricated recipe, single stage rotary let’s use the following; lubricated recipe, single stage rotary screw and two stage rotary screw.screw and two stage rotary screw.

CC13

To select the compressor type, click on the drop down arrow To select the compressor type, click on the drop down arrow to the right of the field. This will exapnd the field as shown to the right of the field. This will exapnd the field as shown above.above.

CC14

Move the cursor until the compressor type you want to choose Move the cursor until the compressor type you want to choose is highlighted and than just click on it to select.is highlighted and than just click on it to select.

CC15

That will collapse the expanded window and the selected That will collapse the expanded window and the selected compressor will be displayed in the field.compressor will be displayed in the field.

CC16

As can be seen from above, all of the compressor types have As can be seen from above, all of the compressor types have been selected for our example.been selected for our example.

CC17

Now we need to select the control type for each of the Now we need to select the control type for each of the compressor types. This is done using the circled fields above.compressor types. This is done using the circled fields above.

CC18

Each compressor type has different control types that can be Each compressor type has different control types that can be chosen. Let us first work with the Lubricated recipe.chosen. Let us first work with the Lubricated recipe.

CC19

The user can click on the drop down arrow to the right of the The user can click on the drop down arrow to the right of the field they want to work with to expand the window as shown field they want to work with to expand the window as shown above.above.

CC20

As can be seen, the only control types being displayed for the As can be seen, the only control types being displayed for the Lubricated recipe are; Five step, Load/Unload, and Three step. Lubricated recipe are; Five step, Load/Unload, and Three step. For our example let us pick load/Unload. Move the cursor and For our example let us pick load/Unload. Move the cursor and click on the choice.click on the choice.

CC21

Our selected control type will appear in the field. For the Our selected control type will appear in the field. For the single stage, expand the drop down menu to display the single stage, expand the drop down menu to display the control types for this type of compressor.control types for this type of compressor.

CC22

As can be seen, the user has six choices for the control type As can be seen, the user has six choices for the control type for a single stage compressor as shown.for a single stage compressor as shown.

CC23

Move the cursor to the type we want to use. For our example, Move the cursor to the type we want to use. For our example, let us use Inlet modulation with sump blowdown.let us use Inlet modulation with sump blowdown.

CC24

As can be seen, the selected control type now appears in the As can be seen, the selected control type now appears in the field next to the single stage rotary screw. Now set the two field next to the single stage rotary screw. Now set the two stage as a variable speed.stage as a variable speed.

CC25

The screen above shows all of the chosen control types for The screen above shows all of the chosen control types for each compressor. Next click on the Chart button above.each compressor. Next click on the Chart button above.

CC26

CC27

This page contains a print function.This page contains a print function.

a refresh page function.a refresh page function.

CC28

CC29

a zoom in and out function.a zoom in and out function.

CC30

a search function.a search function.

CC31

and an export function which allows the user to saveand an export function which allows the user to savethe chart in different formats including PDF, Word, the chart in different formats including PDF, Word, Excel and other formats for easy use in the future.Excel and other formats for easy use in the future.

CC32

When using the export function, this dialog box opens upWhen using the export function, this dialog box opens upwhere the user can name, pick the format and location to savewhere the user can name, pick the format and location to savethe chart for future use.the chart for future use.

The Chart displays The Chart displays the power over the power over capacity curves for capacity curves for each compressor and each compressor and control types using control types using the parameters the parameters inputted on the inputted on the compressor and compressor and system capacity.system capacity.

CC33

The lower the curve The lower the curve is on the chart the is on the chart the more efficient the more efficient the compressor with the compressor with the control type will be control type will be in the system in the system described.described.

CC34

The reason being The reason being that the lower the that the lower the curve on the chart, curve on the chart, the compressor is the compressor is using less power to using less power to to make a certain to make a certain capacity.capacity.

CC35

Therefore the user Therefore the user can compare can compare different compressor different compressor and control types and control types specific to a certain specific to a certain system to determine system to determine which will be the which will be the most efficient.most efficient.CC36

From our example, From our example, the best compressor the best compressor and control type for and control type for the system described the system described is a Two stage is a Two stage rotary screw with rotary screw with Variable speed Variable speed control.control.

CC37

The next best The next best compressor would compressor would be the single stage be the single stage with Inlet with Inlet Modulation with Modulation with blowdown which the blowdown which the red curve.red curve.

CC38

And the worst of the And the worst of the three would be the three would be the Lubricated recip Lubricated recip using Load /Unload using Load /Unload control since it is the control since it is the highest curve on the highest curve on the chart.chart.

CC39

CC40

Closing this page will return the user back to Closing this page will return the user back to the following page.the following page.

CC41

To return to the previous page, click on the RED X at the topTo return to the previous page, click on the RED X at the topof the right hand corner.of the right hand corner.

CC42

Or click on the black X shown above.Or click on the black X shown above.

CC43

Now the user can run other compressor evaluations.Now the user can run other compressor evaluations.

CC44

To close or exit out of the controls comparison, To close or exit out of the controls comparison, click on the Exit button above.click on the Exit button above.

The SETUP button window is used to pick the default units The SETUP button window is used to pick the default units that the program will use to generate a report. You can pick that the program will use to generate a report. You can pick English or Metric units depending on the user preference. It English or Metric units depending on the user preference. It also prefilters the databases for your particular preferences.also prefilters the databases for your particular preferences.

This will open a pop up window. Here the userThis will open a pop up window. Here the usermay alter the default units that the program will use to may alter the default units that the program will use to generate a report. You can pick English or Metricgenerate a report. You can pick English or Metricunits depending on the user preference.units depending on the user preference.

SU2

• The user can choose from the following units for each The user can choose from the following units for each parameter listed;parameter listed;

– Distance:Distance: feet, meters feet, meters– Flow:Flow: ACFM, M3/Hr, M3/min, L/min, L/sec ACFM, M3/Hr, M3/min, L/min, L/sec– Power:Power: HP, KW HP, KW– Pressure:Pressure: PSI, Bar, kpa, K2/M2 PSI, Bar, kpa, K2/M2– Temperature:Temperature: Deg. F, Deg. C Deg. F, Deg. C– Volume:Volume: Ft3, Gallons, Liters, M3 Ft3, Gallons, Liters, M3

SystemWizard 3.6SystemWizard 3.6

SU4

The user can also save chosen parameters as The user can also save chosen parameters as regional setting by using the Save Regional Unitsregional setting by using the Save Regional Unitsbutton shown above. button shown above.

SU5

Clicking on the drop down arrow will expand the Clicking on the drop down arrow will expand the fieldfieldto expose all saved regions in the program. to expose all saved regions in the program.

SU8

This will allow the user to use the saved settings in the futureThis will allow the user to use the saved settings in the futureby selecting the region in the circled field. by selecting the region in the circled field.

SU6

Once the units have been selected and any regions, Once the units have been selected and any regions, defined and saved, click on the “SAVE” button to savedefined and saved, click on the “SAVE” button to saveall new data settings as your default. Please note that the all new data settings as your default. Please note that the selected region pre-filters the libraries to entries for that selected region pre-filters the libraries to entries for that region alone.region alone.

SU9

Currently the “HELP” tab does not function.Currently the “HELP” tab does not function.It will be implemented in the future.It will be implemented in the future.