POWERED SUBWOOFER SYSTEM

POWER ACUOUSTIK

* RCA INPUT/HIGH LEVEL INPUT* P.W.M MOSFET POWER SUPPLY* SOFT DELYED REMOTE TURN-ON* DUAL COLOR INDICATOR L.E.D (POWER/GREEN & PROTECTION/RED)* REMOTE CONTROL FOR SUBWOOFER LEVEL* CONTROL: GAIN, PHASE, LPF, BASS BOOST* PROTECTION CIRCUIT: THERMAL PROTECTION CIRCUIT SHORT PROTECTION CIRCUIT OVERLOAD PROTECTION CIRCUIT* AUTO COOLING

YOUR NEW SUBWOOFER..........

Select a mounting location that allows easy access to the control while driving.Using the subwoofer level control(remote) as a template, mark and drill holes in the mounting surface.

UNDER DECK MOUNTING (Suggestion of the remote placement)

SUBWOOFER MOUNTING LOCATION

INSTALLING THE REMOTE

This

A POWER INPUT TERMINAL (CONNECTING THE POWER Fig. 1)

CONNECTION AND OPERATION

25A

A

G H I J

B

EFDC

25A

The amplifier is equipped with a plug-in auto fuse protecting set against fault conditions. Do not use a fuse with a higher value and never bridge the fuse over.

B FUSE

CONNECTING THE POWER (Fig.1)

Vehicle's chassis ground

To Power antenna

( )

POWER INPUT

C L.E.D

The L.E.D is a dual color indicator, when the +12v and REM +12 voltpower both switch on, The L.E.D illuminated green. this means that the amplifier begin to work. if L.E.D illuminated red colour, this means the amplifier is shut down from protecting circuit(thermal protection & short protection & overload protection).

Use remote wire(accessory) connect "REMOTE SOCKET" to the remote (accessory), the remote is for subwoofer level control.

Fig. 2 Connecting the subwoofer to remote

Rear view of remote controller

25A

D REMOTE (CONNECTING THE SUBWOOFER TO THE REMOTE Fig. 2)

E LINE IN(LOW LEVEL INPUT)

Use a pair of shielded stereo audio cable with RCA type jack connect your receiver's "LOW LEVEL OUT"to the RCA input

LINE IN

L

R

7

1. Remote..........1pc2. Remote wire..........5m3. High level input connector with wire..........1pc4. Mounting magic tape.......2 sets5. Mountint bracket & Screw..........1 set6. manual..........1pc

ACESSORY LIST PER CARTON BOX

J GAINThe "GAIN" control is subwoofer input level control, the input level control should match the output of your radio. After the installion is complete, make sure the input level control is turned down all the way(MIN). Play a tape or CD and turn volume up slowly until you just start to hear distortion, now back the volume down just a bit. On the subwoofer, slowly turn up the input level control(clockwise) until you start to hear distortion and back itdown a bit, Now your radio and subwoofer leves are matched.

I BASS BOOSTVaries from 0dB to 12dB of boost. Frequency adjustment control forbass control filter.

H LPFThe low-pass crossover is continuously variable from 50Hz to 150Hz

G PHASEThe PHASE switch is used for changing woofer phase, set switch from"0 " to "180 ", a phase shift of 180 degrees.o o

1= White, Channel L-2=Black, GND3=White/Black, Channel L+4=Grey, Channel R-5=Grey/Black, Channel R+

F HI INPUT( HIGH LEVEL INPUT)

1 2 3

54

HI INPUT CONNECTOR WIRE(ACCESSORY)

White L- White/Black L+

Grey R-

1

4Grey/Black R+

5

3

Black, GND2

8

SOUND DISTORTED

Input level control adjusted too high

Adjust input level control

Is volume minimum?

LOWHIGH

ITEM

NET WEIGHT

LPF

INPUT SENSITIVITY

800W

<0.4%

>90%

20Hz TO 150Hz

50Hz -150Hz Adjustable

110mV0.5V

25A

10 INCH

400 x 240 x310 mm

8.8kg

0dB-12dBBASS BOOST

DIMENSIONS(L x W x H)

Note: SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.