positioning of wheel stops according to as2890.1:2004€¦ · 18 0800 500 147...

1
18 0800 500 147 [email protected] vanguardgroup.co.nz Carpark & Traffic Management Wheel Stop Installation Procedure Position wheel stop according to AS2890.1:2004. 1. Drill pilot holes approximately 50mm deep using a 10mm masonry bit. 2. Drive spiked fasteners in using sledge hammer ensuring head of fastener is driven into rebated hole. 3. ONTO CONCRETE - Using M12 x 150mm Concrete Screws 1. 2. Move wheel stop aside and drill out the pilot holes using a 12mm masonry bit. Holes must be 25mm deeper than fixing penetration. 3. Position wheel stop according to AS2890.1:2004. Remove dust from holes, reposition wheel stop and insert concrete screws. 4. Drill small pilot holes to mark fixing points. Wind in fixings securely using socket wrench or impact driver. 5. ONTO CONCRETE USING ADHESIVE (Where piercing of waterproof membrane is not allowed) Surface must be clean, dry and dust free. 1. Chalk-mark desired position and roll wheel stop onto its back 2. Spread epoxy around all ground bearing edges and bridges of wheel stop. 3. Position wheel stop according to AS2890.1:2004. Place into position and wriggle slightly to embed into both surfaces 4. Leave undisturbed for 24 hours before subjecting to normal use. Full cure is 7 days. 5. POSITIONING OF WHEEL STOPS ACCORDING TO AS2890.1:2004 Minimum and maximum wheel stop dimensions to comply with AS2890.1:2004 Width 1650mm +/- 50mm Height between 90mm & 100mm Front into a low kerb Rear into a low kerb Front into a high kerb or wall Rear into a high kerb or wall 820mm 1100mm 620mm 900mm WHEEL STOP INSTALLATION PROCEDURE ONTO BITUMEN - Using M12 x 300mm Rebar Spikes

Upload: others

Post on 27-Jan-2021

1 views

Category:

Documents


0 download

TRANSCRIPT

  • 18

    0800 500 147 [email protected] vanguardgroup.co.nz

    Ca

    rpa

    rk &

    Tra

    ffic

    Ma

    na

    ge

    me

    nt

    Wheel Stop Installation Procedure

    Position wheel stop according to AS2890.1:2004.

    1. Drill pilot holes approximately 50mm deep using a 10mm masonry bit.

    2. Drive spiked fasteners in using sledge hammer ensuring head of fastener is driven into rebated hole.

    3.

    ONTO CONCRETE - Using M12 x 150mm Concrete Screws

    1. 2. Move wheel stop aside and drill out the pilot holes using a 12mm masonry bit. Holes must be 25mm deeper than fixing penetration.

    3.Position wheel stop according to AS2890.1:2004.

    Remove dust from holes, reposition wheel stop and insert concrete screws.

    4.

    Drill small pilot holes to mark fixing points.

    Wind in fixings securely using socket wrench or impact driver.

    5.

    ONTO CONCRETE USING ADHESIVE(Where piercing of waterproof membrane is not allowed) Surface must be clean, dry and dust free.

    1. Chalk-mark desired position and roll wheel stop onto its back

    2. Spread epoxy around all ground bearing edges and bridges of wheel stop.

    3.Position wheel stop according to AS2890.1:2004.

    Place into position and wriggle slightly to embed into both surfaces

    4. Leave undisturbed for 24 hours before subjecting to normal use. Full cure is 7 days.

    5.

    POSITIONING OF WHEEL STOPSACCORDING TO AS2890.1:2004

    Minimum and maximum wheel stop dimensions to comply with AS2890.1:2004

    Width 1650mm +/- 50mm

    Heightbetween

    90mm & 100mm

    Front into a low kerb Rear into a low kerb

    Front into a high kerb or wall Rear into a high kerb or wall

    820mm 1100mm

    620mm 900mm

    WHEEL STOP INSTALLATION PROCEDURE

    ONTO BITUMEN - Using M12 x 300mm Rebar Spikes