–1–11111111111111111–1––1––1––111–1–

www.imetco.com

Any Building In Any Place At Any Time

Could Be Called Upon to Protect the Contents Within

The turn of the century brought a rash of severe weather events and the promise of a dynamic climate that will continue to produce these natural assaults. Experts around the world agree that we are at the precipice of an extreme weather era. Whether due to global warming or simply following cyclical trends, it seems clear that the frequency and severity of high-velocity wind events will continue to place demands on our structural environment.

Some of the more notorious storms of the decade precipitated intensive study of the vulnerability of roofing systems by organizations such as the Roofing Industry Committee on Weather Issues (RICOWI) and Factory Mutual Global (FM). These studies revealed that the vast majority of all weather-related losses (75%) were due to roof failures, and of those, more than half were due to perimeter failure.

As a result, building codes and standards have evolved to demand better design and performance of roofing systems. The 2003 and subsequent editions of the International Building Code (IBC) contain provisions requiring edge-metal flashings (copings, fascia, gravel stop) to be designed and installed in accordance with ANSI/SPRI ES-1, “Wind Design Standard for Edge Systems Used with Low Slope Roof Systems.”

1504.5 Edge securement for low-slope roofs. Low-slope membrane roof system metal edge securement, except gutters, shall be designed and installed for wind loads in accordance with Chapter 16 and tested for resistance in accordance with ANSI/SPRI ES-1, except the basic wind speed shall be determined from Figure 1609.

Although these studies and the adoption of the ES-1 standard by IBC are most directly attributable to the destruction inflicted by hurricanes, events such as straight-line winds and tornadic activity associated with common seasonal storms inflict wide-spread damage each year. FEMA has divided the United States into four zones that reflect the number and strength of extreme windstorms encountered in each region. The tables to the right clearly illustrate that no area is immune to wind-related roofing damage.

–3–

That’s Why We Bring You

PerformaEdge

A line of performance-inspired Edge Systems from IMETCO

ES-1 CertificationEdge Systems from IMETCO have successfully passed the three tests required by the ANSI/SPRI ES-1 standard:

RE-1: Roof Edge Termination Test1. The RE-1 test evaluates the perimeter attachment to a minimum holding power of 100 pounds per foot. The membrane is pulled at a 45-degree angle to the roof deck to simulate a billowing. Failure occurs when the membrane detaches from the edge termination, or the termination detaches from its mounting.

RE-2: Pull-off Test for Metal Edge 2.

FlashingRE-2 evaluates the strength of the metal edge flashing to ensure that the fascia system meets or exceeds the building’s calculated design wind pressure. An incremental load is applied to the face of the specimen and held for 60 seconds, then removed and increased in increments of 25 psf until 150 psf, then increments of 10 psf are applied thereafter. The results must meet or exceed the calculated design pressure of the building. Failure occurs with securement loss of any component of the roof edge, or deformation that would hinder weather protection at the edge.

RE-3: Pull-off Test for Metal Wall 3.

CopingRE-3 evaluates the strength of a metal coping cap to ensure that it meets or exceeds the building’s calculated design wind pressure. Incremental loads are applied as with the RE-2 test, where the load is applied to the face and top simultaneously. Failure occurs with the securement loss of any component of the roof edge system, or deformation that would hinder weather protection at the edge.

www.imetco.com

ES-FX™ Series Fascia

IMETCO’s line of Edge Systems includes our strongest and most versatile fascia, the ES-FX. This extruded aluminum fascia is compatible with most of the roof systems marketed today. From the multi-ply built-up roofs to single ply systems to thicker modified bituminous membranes, the ES-FX fascia system can easily adjust to each one.

Face dimensions of the ES-FX fascia system provide coverage for up to three nailers. Engineered with its Vari-tightTM flashing component, ES-FX allows for installation with various roof membrane types and thicknesses without any penetration of the membrane. The Vari-tightTM screws supplied with the system allow for removal and replacement of the fascia cover in retrofit applications, helping to reduce costs and to expedite project completion. The consistent and crisp lines of the extruded cover cannot be matched by a formed product.

ANSI/SPRI ES-1 approvedTested face dimensions up to 9 inchesEngineered three-piece design allows various roof membrane thicknesses20-year Blow-Off / Leak-Tight warranty available20-year finish warranty available10-foot standard length24- and 22-gauge galvanized steel cant damFascia fasteners includedConcealed 6-inch splice plate Heavy gauge extruded aluminum cover Post-coated Kynar® standard and custom colorsMill finish available Mitered and welded factory fabricated corners & accessoriesNo penetration of the roof membraneFully welded radii available

ES-FX Fascia

Product: Face Size:

ES-FX600 6.0 inches

ES-FX750 7.5 inches

ES-FX900 9.0 inches

SPECIFY

2 1/2"

1"CANT DAM x 10'-0"

6" CONCEALED SPLICE PLATE @ EACH JOINT

MEMBRANE FLASHING (by OTHERS)

1 1/4" ROOFING NAIL @ 12" o.c. MAX.(by OTHERS)

FASCIA COVER x 10'-0"

FASTENER @ 18"o.c. (by IMETCO)

VARI-TIGHT FLASHING (by IMETCO)

1 1/4" ROOFING NAIL @ 18" o.c. MAX.(by OTHERS)

–5–

ES-F™ Series Fascia

The old-school gravel stop and fascia of the past is no longer acceptable for most roof systems of today. Fascia systems must be tested and approved to meet the ANSI/SPRI ES-1 standard as required by the IBC.

Once again, with its line of fully tested Edge Systems, IMETCO demonstrates its commitment to our customers by providing a full line of performance-inspired fascia and coping systems.

Features and Benefits:ANSI/SPRI ES-1 approvedTested face dimensions up to 9½ inchesTwo-piece design10-foot standard lengths standard (other lengths available)24- and 22-gauge galvanized steel cant damsConcealed 6-inch splice plate Factory fabricated corners and accessoriesDoes not penetrate the roof membraneNo exposed fastenersInstalls securely with various roof membrane thicknesses20-Year Blow-Off/Leak-Tight Warranty available20-Year Finish Warranty available

Materials and Coatings.040, .050 & .063 aluminum 24- and 22-gauge galvanized steel24- and 22-gauge stainless steelPre-finished Kynar® coated aluminum and steel standardPost-coated Kynar® custom colors available

SPECIFY

1 1/2"

1/2"

1/2"

1 3/4"

FASCIA CANT x 10'-0"

6" CONCEALED SPLICE PLATE @ EACH JOINT

MEMBRANE FLASHING (by OTHERS)

1 1/4" ROOFING NAIL @ 12" o.c. MAX.(by OTHERS)

FASCIA COVER x 10'-0"

1 1/4" ROOFING NAIL @ 12" o.c. MAX.(by OTHERS)

ES-F Fascia

Product: Face Size:

ES-F500 5.0 inches

ES-F650 6.5 inches

ES-F800 8.0 inches

ES-F950 9.5 inches

www.imetco.com

ES-C™ Series Coping

Edge Systems from IMETCO are engineered for performance. A leader in highly engineered structural standing seam metal roofing, IMETCO understands the need for tested and secure metal Edge Systems. IMETCO tests our coping system based on the “real-life” ANSI/SPRI ES-1 method to meet or exceed your specific project requirements. That’s why our ES-C Series Coping system is one of the strongest in the industry.

Features and Benefits:ANSI/SPRI ES-1 approvedTested wall widths up to 24 inchesTested face dimension up to 6 inchesSnap on design10-foot standard lengths (other lengths available)Install on wood nailers, masonry or steel parapet wallsHeavy-gauge galvanized steel anchor plates (5’ o.c. standard placement)Anchor plate fasteners includedConcealed 6-inch splice plate with butyl sealant tapeMitered and fully welded corners, end caps, transitions, etc.Single slope, peaked & flat profilesFully welded radii20-Year Blow-Off/Leak-Tight Warranty available20-Year Finish Warranty available

Materials and Coatings.040, .050, .063, .080 & .125 aluminum 24- and 22-gauge galvanized steel24- and 22-gauge stainless steelPre-finished Kynar® coated aluminum and steel standardPost-coated Kynar® custom colors available

(ACTUAL WALL WIDTH)

"A"

"B""C"

(4" STD.)

(4" STD.)

1/4"

3/4"

CLEARANCE FORWALL VARIATIONS

1 3/8"

COPING COVER x 10'-0"

6" CONCEALED SPLICE PLATE @ EACH JOINT

ANCHOR PLATE @ 5'-0" o.c.

(4) FASTENERS PER ANCHOR PLATE

(ACTUAL WALL WIDTH)

"A"

"B" "C"(4" STD.)(4" STD.)

1/8" CLEARANCE FORWALL VARIATIONS

1/8"

3/4"5/8"

COPING COVER x 10'-0"

6" CONCEALED SPLICE PLATE @ EACH JOINT

ANCHOR PLATE @ 5'-0" o.c.

(4) FASTENERS PER ANCHOR PLATE

ES-C Sloped Coping

ES-C Peaked Coping

–7–

4"

(SPECIFY)

(SPECIFY)

EQUAL

EQUAL

1 1/2"

(SPECIFY)

1 1/2"

1 1/2"

4"

(SPECIFY)

SPECIFY

"A"

"B" "C"(4" STD.)(4" STD.)

5/8"5/8"

7/8"

(ACTUAL WALL WIDTH)

"A"

"B""C"

(4" STD.)

(4" STD.)

5/8"

7/8"

(SPECIFY)

1"

1" 1"

(SPECIFY)

(SPECIFY)

1"

1" 1"

(SPECIFY)

2"

1"

(SPECIFY)

(SPECIFY)

EZ Edge™ Formed Line

IMETCO’s EZ Edge line combines quality with economy. These products offer proven reliability and pleasing aesthetics at a lower cost than performance-inspired edge systems. All of the EZ Edge products are available with a 20-year Kynar® finish warranty, and the fascia and coping is available with a weather-tight warranty up to 10 years.

Features and Benefits:Factory fabricated and field provenStandard and project-specific profiles & sizes Simple, strong design10-foot standard lengths (other lengths available)Concealed 6-inch splice plates Standard factory-fabricated corners, end caps, etc. Mitered and fully welded corners, end caps, transitions, etc. availableFully welded radius coping, fascia & gutter 20-Year Blow-Off/Leak-Tight Warranty available20-Year Finish Warranty available

Materials and Coatings.032, .040, .050, .063, .080 & .125 aluminum 24- and 22-gauge galvanized steel24-gauge stainless steelPre-finished Kynar® coated aluminum and steel standardPost-coated Kynar® custom colors available

EZ Edge Sloped and Peaked Coping

EZ Edge Formed Fascias and Extender

EZ Edge “A” and “D” Style Gutter, and Downspout

www.imetco.com

Premium Colors

Platinum Silver Roman Copper

Brite Copper Champagne

Preweathered Galvalume Galaxy Blue

IMETCO’s 28 standard, designer and premium colors are all “cool” colors, with SR measurements of .25 or better. Custom colors and specialty finishes are also available. Ask your IMETCO representative for more information, or to request a color chart.

The Total SolutionIMETCO offers a full line of metal roofing, wall, and edge systems and accessories.Be sure to ask your representative for information about other products and solutions from IMETCO, such as:

Series 300 Standing Seam Metal Roofing System• Precision engineering for long-term

weather-tight performance• Rigorously tested to be leakproof and to

withstand hurricane-force winds• Ideal for structural and/or architectural

applications• One-piece clip that facilitates unlimited

thermal movement• Features a 2⅜-inch high symmetrical

seam with a separate, easy-to-install seam cap

• Factory-applied hot-melt sealant that remains isolated from the clip

• Can be curved or tapered

Total Metal Roof and Deck System• Series 300 standing seam metal roofing

from IMETCO• Metal deck and insulation system from

Martin Fireproofing• Single warranty for complete assembly

DryDek® Underlayment• Heat tolerant (260+°f)• Engineered for metal and tile roofing• Self-adhering, self-sealing• 100% SBS-modified, f iberglass-

reinforced• 150-day exposure resistance

The IMETCO AdvantageFor more than a decade, we at IMETCO have enjoyed our reputation as a manufacturer committed to providing products of only the highest quality. Our staff comprises expertise in metal roofing, design, engineering, testing, code compliance, manufacturing, and more. Above all, our staff excels in providing unparalleled customer service.

At IMETCO, your satisfaction

is our only measure of success!

2070 Steel Drive � Tucker, GA 30084 800.646.3826 (p) � 770.908.2264 (f)

www.imetco.com

Standard Colors

Irish Mist Almond Suede Emerald Forest Blue Sapphire

Tuscan Slate Epic Bronze Solar White Cadet Gray

Sandstone Chestnut Georgian Brick Opal Star

Colonial Red Silver Cloud Wedgewood Weathered Copper

Designer Colors

Iron Mountain Cardinal Red Carolina Coast

Natural Patina Caribbean Coral Merlot

Galvalume® is steel pre-treatment and a registered trademark of Biec International Inc.

Hylar® is a fluorocarbon paint finish available on our metal products, and is a registered trademark of Ausimont USA Inc. Kynar® is a fluorocarbon paint finish available on our metal products, and is a registered

trademark of Elf Atochem North America Inc.

FM® (Factory Mutual) is a world leader in property loss prevention and control engineering, research, and training. Its research-based recommendations set new standards that reduce the chance of property

loss due to fire, weather conditions, and failure of electrical or mechanical equipment. It is a registered trademark of Factory Mutual Global, and must be identified as such whenever referred to in print.

Series 300® and all other trademarks are owned by Innovative Metals Company, Inc. (IMETCO).

The colors above are for reference only. To select your final color, please request a metal color sample.