pe100-1 power extender - levitoncommunities.leviton.com/servlet/jiveservlet...leviton’s pe100-1...
TRANSCRIPT
PE100-1ProductSpecifications
APPLICATIONLeviton’s PE100-1 Power Extender allows a dimmingzone’s power handling capacity to be extended to afull 1920W/VA on 120V input power. It allows a zoneto dim or switch a fully loaded circuit of incandescentand magnetic low voltage loads only.
FEATURES & BENEFITS• Works with incandescent, magnetic low voltage,
halogen or neon/cold cathode lighting• Low-end trim available for setting the
minimum brightness level• Emulates the characteristics of the dimmer
that it is connected to in terms of dimming range and resolution
• Works with any Dimensions Multi-zoneController/Dimmer to extend load capacity on any zone
PE1 00-1 P
ower Exten
der
1900 Box
(4 Places)
PoExtender
PoWallplate
TOP
2 Gang Raised Cover
1900 Box
(4 Places)
TOP
2 Gang Raised Cover
PoWallplate
PoExtender
1
Leviton Mfg. Co., Inc. 59-25 Little Neck Pkwy • Little Neck, NY 11362-2591 • Tech Line: 1-800-824-3005 • Fax: 1-800-832-9538
Visit our Website at: www.leviton.com
JOB NAME:
JOB NUMBER:
CATALOG NUMBERS:
SPECIFICATION SUBMITTAL
Figure 2: Flush Mounting
MOUNTINGAll Power Extenders must have 4-1/2"spacing above and below each unit forproper ventilation and heat dissipation(refer to figure 3). Line voltage wiringshould be at least 6ft away from sound orelectronic equipment wiring. Mount PowerExtender to wall box with “TOP” facing upas follows: For Wall Box Mounting (referto figure 1), for Flush Mounting (refer tofigure 2) and for Panel Mounting (notshown), proceed as follows:a. The enclosure must be in accordancewith all local and national electrical codes.b. Leviton DOES NOT recommend using adoor to enclose the front of a panel, sincethis restricts airflow to the controls.c. If mounting multiple controls in anenclosure:• Ambient timperature within an enclosure“MUST REMAIN BETWEEN”32o-104oF(0o-40oC).• If not mounting in a metal enclosure, allunits “MUST” be mounted in a wall box.d. To improve heat dissipation of controls,remove the faceplate from the unit.
T
T
Minimum
Minimum
Figure 3: Front View Spacing
Figure 2: Flush Mounting
Figure 1: Surface Mounting
PE100-1 Power Extender
2.06(52.3 mm)
2.80
(71.
1 m
m)
4.72
(119
.9 m
m)
4.50(114.3 mm)
Extender
Controller/Dimmer
Hot (Black)
(Load)
Neutral (White)
(120VAC)
Ground
LOAD
Neutral
Load
Line
NE
UT
RA
L
NE
UT
RA
L
LO
AD
HO
T
HO
T
CO
NT
RO
L
Leviton Mfg. Co., Inc. 59-25 Little Neck Pkwy • Little Neck, NY 11362-2591 • Tech Line: 1-800-824-3005 • Fax: 1-800-832-9538
Visit our Website at: www.leviton.com © Copyright 2003 Leviton Manufacturing Co., Inc. All rights reseved. G-6723/G3
ProductSpecifications PE100-1.........................
Used if Dimmer/Switch has Neutral connection
Hot (Black)
(Load)
Neutral 2 (White)
Neutral 1 (White)
Line 1 (120VAC)
LOAD
Dimmer
Ground
Hot (Black)Line 2 (120VAC)
White
Load
Black
PowerExtender
NE
UT
RA
L
NE
UT
RA
L
LO
AD
HO
T
SW
ITC
HH
OT
CO
NT
RO
L
PowerExtender
D3206/08Controller/Dimmer
Hot (Black)
Hot (Black)
(Load)(Load)
Neutral (White)
Neutral (White)
Neutral (White)
Line (120VAC)
Line 1 (120VAC)
Hot (Black)Line 2 (120VAC)
Ground
LOAD 1
LOAD 2
Neutral
Load
Line
NE
UT
RA
L
NE
UT
RA
L
LO
AD
HO
T
SW
ITC
HH
OT
CO
NT
RO
L
PowerExtender
NE
UT
RA
L
NE
UT
RA
L
LO
AD
HO
T
SW
ITC
HH
OT
CO
NT
RO
L
Extender
Controller/Dimmer
Hot (Black)
Hot (Black)
(Load)
Neutral 2 (White)
Neutral 1 (White)
Line 1 (120VAC)
Line 2 (120VAC)
Ground
LOAD
Neutral
Load
Line
NE
UT
RA
L
NE
UT
RA
L
LO
AD
HO
T
HO
T
CO
NT
RO
L
Used if Dimmer/Switch has Neutral connection
Hot (Black)
(Load)
Neutral (White)
(120VAC)
LOAD
Dimmer
Ground
White
Load
Black
Extender
NE
UT
RA
L
NE
UT
RA
L
LO
AD
HO
T
HO
T
CO
NT
RO
L
Wiring Diagram 1B: Single Feed Wiring Application w/Dimmer
Wiring Diagram 1A: Single Feed Wiring Application w/Controller
Wiring Diagram 2B: Dual Feed Wiring Application w/DimmerWiring Diagram 2A: Dual Feed Wiring Application w/Controller
Wiring Diagram 3: Dual Feed Wiring Application w/Dimmer and Two Power Extenders
Single Feed WiringLine Hot can becontrolled by onecircuit breaker aslong as the totalload does notexceed the rating of the circuit breakers.
Single Feed WiringLine Hot can becontrolled by onecircuit breaker aslong as the totalload does notexceed the rating of the circuit breakers.
Dual Feed WiringThe Input controlcircuit and theOutput load circuitcan be supplied bytwo circuit breakerson a single phase or by two separate phases.
Dual Feed WiringThe Input controlcircuit and theOutput load circuitcan be supplied bytwo circuit breakerson a single phase or by two separate phases.
Dual Feed WiringThe Input controlcircuit and the Output load circuitcan be supplied by two circuitbreakers on a single phase or by two separatephases.
Note:Up to 4 PowerExtenders canbe Connectedtogether.
SPECIFICATIONS
Compatibility• For Box-Mounted Dimmers: Must use a
120V, 600W Incandescent version from the following families: IllumaTech™, Mural™, True Touch™, ToggleTouch™, TouchPoint™ and Home Controls
• For Monet™ installations, use a 120V, 600VA Monet Magnetic Low Voltage dimmer (requires a Neutral wire)
• For dimmers that include a Neutral wire (such as some scene-capabledimmers), the dimmer Neutral wire must be connected
• For Architectural Systems: Works with all families
ElectricalInput Voltage: 120V, 50/60HzLoad Rating: 1920W/VALoad Output Power: Phase independent of control deviceDimmer Input: 120V 50/60HzTesting/Code Compliance: UL Listed, CSA Certified and FCC Part 15
PhysicalColor: Aluminum clear anodized extruded heat sink with a snap-on molded white coverSize: 4.72"L x 4.5"W x 0.5"H (120mm x 114mm x 12.7mm)
EnvironmentalOperating Temperature Range: 0ºC to 40ºCStorage Temperature Range: -10ºC to 85ºCRelative Humidity: 20%-90% non-condensing
Warranty: Limited 2-Year Warranty