pcb routers - ind-sphinxindsphinx.com/wp-content/uploads/2017/12/pcb-routers.pdf · 0.40 0.60 0.80...
TRANSCRIPT
PACKINGADVANTAGESAPPLICATION
w w w . i n d s p h i n x . c o m+91 1792 232860 / [email protected]
Routing of aluminium
Routing of IMS/metal PCB / Heat sink PCBs.
Longer tool life
Better finish
No pre drilling
SCAN TO ORDER
d lD : Ø 1/8" (3.175 mm) Common Shank On Request Shank Dia 3mm
10 tools per pack.50 tools per pack.
2F ALUMINIUM ROUTER
1.60
2.40
8.00
9.00 -
Tabulated parameters provide guidelines which acts as starting points for optimising speeds and feeds at the user's end.
RECOMMENDED PARAMETERS FOR ROUTING ALUMINIUM PCB
DIAMETER mm
1.60
2.00
SPINDLE SPEEDRPM
40000
32000
CHIP LOADmicron m/min
ROUTING DEPTHm/min mm
5.0 - 7.0
9.0 -15.0
0.2 - 0.3
0.3 - 0.5
1.2
1.2
2.00
2.50
1.0
1.0
2.40 28000 14.0 - 21.0 0.4 - 0.6 1.2 3.00 1.0
X-Y TABLE FEED Z-FEED RATE DEPTH IN TO BACK UP
P024
On request : Inch sizes / Special dimensions
: Non stock items / Articles
PCBIMS
2.00 9.00 -
-
3.00 10.00 -
3.00 23000 26.0 - 35.0 0.6 - 0.8 1.2 3.00 1.0
Also available
DLCCOAT
ØD
l38.00
ød
mm mm
w w w . i n d s p h i n x . c o m+91 1792 232860 / [email protected]
For routing of all standard PCBs with aggressive feed rates on rugged spindles.
Long life and excellent performance under good vacuum conditions.
SCAN TO ORDER
d lD : Ø 1/8" (3.175 mm) Common Shank On Request Shank Dia 3mm
1.201.30*1.40*1.501.601.70*1.802.002.402.50*
0.800.90*1.00
0.60* 3.000.50* 3.00
5.005.005.008.008.008.008.008.008.008.00
5.005.005.00
------9.50*9.50*10.50*10.50
---
1.10 5.00* 7.00
PATTERNDIAMOND
10 tools per pack.50 tools per pack.
Tabulated parameters provide guidelines which acts as starting points for optimising speeds and feeds at the user's end.
SPINDLE SPEEDRPM
RECOMMENDED PARAMETERS FOR ROUTING FR4
DIAMETER mm
1.001.201.301.401.501.601.701.802.002.40
0.600.800.90
50000500004700043000400003800036000340003000035000
700007000070000
X-Y TABLE SPEEDm/min
0.4 - 0.60.5 - 0.70.5 - 0.70.5 - 0.70.6 - 0.80.6 - 0.80.7 - 1.00.7 - 1.01.0 - 1.41.4 - 1.6
< 0.2< 0.4< 0.4
Z-FEED RATEm/min
0.40.40.50.50.50.50.50.50.50.5
0.20.20.2
UPCUT POINT
DRILLArticleP661*
FISHTAILUPCUTArticle
P660
PACKINGADVANTAGESAPPLICATION
HIGH FEED DIAMOND CUT ROUTER
ØDØd
l38.00
P660P661
On request : Inch sizes / Special dimesions
: Non stock items / Articles
mm mm
PACKINGADVANTAGESAPPLICATION
UPCUTDOWNCUT
FISHTAIL
w w w . i n d s p h i n x . c o m+91 1792 232860 / [email protected]
Diamond patterned standard router used for routing outer contours in PCBs.
Long life and excellent performance under efficient vacuum conditions.
SCAN TO ORDER
d lD : Ø 1/8" (3.175 mm) Common Shank On Request Shank Dia 3mm
1.201.30*1.40*1.50 / 1.601.802.002.10* / 2.20*2.30*2.402.50*
0.80* / 0.90*1.001.10*
2.60* / 2.80*2.90*
3.175*3.00*
0.70*
5.005.005.008.508.509.009.009.009.009.00
5.005.005.00
9.009.009.009.00
PATTERNDIAMOND
10 tools per pack.50 tools per pack.
Tabulated parameters provide guidelines which acts as starting points for optimising speeds and feeds at the user's end.
SPINDLE SPEEDRPM
RECOMMENDED PARAMETERS FOR ROUTING FR4
DIAMETER mm
1.001.201.301.401.501.601.701.802.002.40
0.800.90
2.503.003.175
50000500004700043000400003800036000340003000025000
7000070000
240002000020000
X-Y TABLE SPEEDm/min
0.4 - 0.60.5 - 0.70.5 - 0.70.5 - 0.70.6 - 0.80.6 - 0.80.7 - 1.00.7 - 1.01.0 - 1.41.0 - 1.4
< 0.4< 0.4
1.0 - 1.41.0 - 1.31.0 - 1.3
Z-FEED RATEm/min
0.40.40.50.50.50.50.50.50.50.5
0.20.2
0.50.50.5
ArticleP627*
FISHTAILUPCUTArticle
P626
DIAMOND CUT ROUTER P626P627
7.007.007.00--10.5010.50*10.50*10.5010.50
7.007.007.00
--10.5010.50
mm mm
On request : Inch sizes / Special dimensions
: Non stock items / Articles
ØDØd
l38.00
5.00 -
UPCUTUPCUT
PACKINGADVANTAGESAPPLICATION
w w w . i n d s p h i n x . c o m+91 1792 232860 / [email protected]
Spiral patterened standard router used for routing outer contours and inner contours of PCBs.
Routing of inner slotting in the PCBs.
Smooth edge finish .
Good dimensional control because of efficient chip evacuation.
SCAN TO ORDER
d lD : Ø 1/8" (3.175 mm) Common Shank On Request Shank Dia 3mm
10 tools per pack.50 tools per pack.
Tabulated parameters provide guidelines which acts as starting points for optimising speeds and feeds at the user's end.
SPINDLE SPEEDRPM
RECOMMENDED PARAMETERS FOR ROUTING FR4
DIAMETER mm
70000580005400050000460004300041000390003500029000
7000070000
7000070000
X-Y TABLE SPEEDm/min
0.4 - 0.60.5 - 0.70.5 - 0.70.5 - 0.70.6 - 0.80.6 - 0.80.7 - 1.00.7 - 1.01.0 - 1.41.0 - 1.4
< 0.3< 0.4
< 0.1< 0.2
Z-FEED RATEm/min
0.40.40.50.50.50.50.50.50.50.5
0.20.2
0.20.2
ArticleP727*LHRC
ArticleP726
BREAKERCHIP
2800023000
1.0 - 1.41.0 - 1.3
0.50.5
22000
1.001.201.301.401.501.601.701.802.002.40
0.600.80
0.400.50
2.503.003.175 1.0 - 1.3 0.5
2.402.50* - 2.90*3.003.175*
9.00
5.005.005.005.005.008.508.508.509.00
4.005.00
2.003.00
9.009.009.00
6.007.007.007.007.00----
5.006.00
-4.00
---
- -
7.00*8.50*8.50*8.50*8.50*----
-7.00*
--
---
DOWNCUT
FISHTAILFISHTAIL FISHTAILUPCUTArticle
P724*LHLC
UPCUTArticle
P729*POINTDRILL
CHIP BREAKER ROUTER P726P727
P724P729
0.90
1.10*1.201.30* - 1.40*1.50*1.601.70* - 1.90*2.00
0.70*0.80
0.40*0.50* - 0.60*
1.00
mm mm
On request : Inch sizes / Special dimensions
: Non stock items / Articles
l38.00
Ød ØD
2.10* 9.00 - -
l38.00
Ød ØD
BREAKERCHIP
w w w . i n d s p h i n x . c o m+91 1792 232860 / [email protected]
Spiral patterened standard router used for routing outer contours and inner contours PCBs.Routing of inner slotting in the PCBs.
Smooth edge finish.
Good dimensional control because of efficient chip evacuation.
SCAN TO ORDER
d lD : Ø 1/8" (3.175 mm) Common Shank On Request Shank Dia 3mm
0.40*0.50*0.60
2.503.003.00
10 tools per pack.50 tools per pack.
Tabulated parameters provide guidelines which acts as starting points for optimising speeds and feeds at the user's end.
RECOMMENDED PARAMETERS FOR ROUTING FR4
SPINDLE SPEED
70000700007000070000580005400050000460004300041000
1190009500080000
39000350002900028000
X-Y TABLE SPEED
0.3 - 0.40.3 - 0.40.3 - 0.40.4 - 0.60.5 - 0.70.5 - 0.70.5 - 0.70.6 - 0.80.6 - 0.80.7 - 1.0
< 0.2< 0.3< 0.3
0.7 - 1.01.0 - 1.41.0 - 1.41.0 - 1.4
Z-FEED RATE (m/min)
0.5
0.40.40.40.50.50.5
0.20.20.20.2
0.20.20.2
0.50.50.5
FISHTAILArticleP732
HIGH PERFORMANCE CHIP BREAKER ROUTER P732
DIAMETER
0.700.800.901.001.201.301.401.501.601.70
0.400.500.60
1.802.002.402.50
0.40.40.40.4
0.40.40.4
1.01.01.01.0
0.80.80.8
1.21.21.4
Without Pre-Drilling With Drillingm/minRPMmm
UPCUT
On request : Inch sizes / Special dimensions
: Non stock items / Articles
mm mm
PACKINGADVANTAGESAPPLICATION
---
1.00
1.201.30* / 1.40*1.501.601.802.002.402.503.003.175
-0.80 5.00
5.00
5.005.006.007.507.507.508.508.508.50*8.50*
-
7.00*---------
-0.90* 5.00
-1.10* 5.00
0.400.600.801.001.201.602.002.403.003.175
101834445355
2468
101834445355
2468
46810122240526466
46810142535404550
1-21-2235812151820
46810142535404550
1-21-2235812151820
46810142535404550
w w w . i n d s p h i n x . c o m+91 1792 232860 / [email protected]
Routing teflon and flexible boards.
Soft plastic,foils,PE,PTFE,Polymide, PMMA routing.
For material producing long chips Aluminium,Copper,Brass.
Thin prepegs routing.
SCAN TO ORDER
d lD : Ø 1/8" (3.175 mm) Common Shank On Request Shank Dia 3mm
10 tools per pack.50 tools per pack.
Tabulated parameters provide guidelines which acts as starting points for optimising speeds and feeds at the user's end.
RECOMMENDED PARAMETERS FOR ROUTING
MATERIAL
SINGLE FLUTE ROUTER P926
PCBFR
PCBIMS
PCBCEM POLYIMIDE
FLEXIBLE
CUTTING SPEED (m/min) FR-4 FR-2 CEM 3 CEM 1 PE PTEF POLYIMIDE AI Cu/BRASS
190 - 200 160 - 180 160 - 180 160 - 180 100 - 120 100 - 120 100 - 120 200 - 250 180 - 220
ArticleP926
2.003.003.003.003.004.004.004.005.005.008.008.009.009.009.00
0.400.500.600.801.001.201.401.501.601.802.002.402.503.003.175
Diameter mm Chip Load microns
46810142240526466
PCBød Ø
D
38.00l
PACKINGADVANTAGESAPPLICATION
On request : Inch sizes / Special dimensions
: Non stock items / Articles
mm mm
SAFEEND
PACKINGADVANTAGESAPPLICATION
POINTDRILL
w w w . i n d s p h i n x . c o m+91 1792 232860 / [email protected]
Routing of aluminium and copper panels.
Routing of IMS/metal PCB / Heat sink PCBs.
Depth routing with flat/square end style router.
SCAN TO ORDER
d lD : Ø 1/8" (3.175 mm) Common Shank On Request Shank Dia 3mm
10 tools per pack.50 tools per pack.
2F ALUMINIUM ROUTER
0.40*0.50*0.60*0.70*0.801.001.201.40*1.501.601.80*2.002.402.50*3.003.175*
2.002.503.003.003.004.004.004.005.005.006.007.007.008.008.008.00
--------------10.00-
Tabulated parameters provide guidelines which acts as starting points for optimising speeds and feeds at the user's end.
RECOMMENDED PARAMETERS FOR ROUTING ALUMINIUM PCB
DIAMETER mm
1.001.201.401.501.601.802.002.402.503.00
0.400.600.80
SPINDLE SPEEDRPM
70000580005000046000440003900035000290002800023000
800008000080000
CHIP LOADmicron m/min
ROUTING DEPTHm/min mm
4.35.28.08.79.110.311.417.217.930.4
0.61.32.5
31.8
0.30.30.40.40.40.40.40.50.50.7
0.050.10.2
0.80.80.81.01.21.21.21.21.21.2
0.20.40.6
1.2
1.201.501.502.002.002.202.503.003.003.00
0.500.501.00
3.00
0.60.60.60.80.80.80.80.80.81.0
0.30.30.4
1.0
X-Y TABLE FEED Z-FEED RATE PRE DRILLED DEPTH IN TO BACK UP
3.175 22000 0.7
P424P422
On request : Inch sizes / Special dimensions
: Non stock items / Articles
PCBIMS
ØDød
38.00l
ØD
l38.00
ød
SAFEENDArticle
P422*ArticleP424
mm mm
w w w . i n d s p h i n x . c o m+91 1792 232860 / [email protected]
Routing aluminium and copperheat sinks.
Routing flexi and flexirigid boards.
Excellent surface finish for plated through holes.
SCAN TO ORDER
d lD : Ø 1/8" (3.175 mm) Common Shank On Request Shank Dia 3mm
0.80
1.201.501.601.902.00
3.00*3.175*
0.25 - 0.30*0.40*0.50* - 0.70
2.40
10 tools per pack.50 tools per pack.
Tabulated parameters provide guidelines which acts as starting points for optimising speeds and feeds at the user's end.
RECOMMENDED PARAMETERS FOR ROUTING
MATERIAL
APPLICATION
FISHTAILArticleP826
2 FLUTE ROUTER P826P820
CUTTING SPEED m/min FR-4 FR-2 CEM 3 CEM 1 PE PTEF POLYIMIDE Al Cu/BRASS
190 - 200 160 - 180 160 - 180 160 - 180 100 - 120 100 - 120 100 - 120 200 - 250 180 - 220
0.801.001.201.602.002.403.003.175
0.250.400.60
335812151820
122
68101834445355
345
68101834445355
345
810122240526466
356
810122240526466
356
810142535404550
356
810142535404550
356
810142535404550
356
335812151820
122
ArticleP820*
ØDød
38.00l
Diameter mm Chip Load microns
PCBIMS
PCBFR
PCBCEM POLYIMIDE
FLEXIBLE
PCB
mm mm
On request : Inch sizes / Special dimensions
: Non stock items / Articles
PACKINGADVANTAGESAPPLICATION
SAFEEND
2.50
1.001.10
5.005.00
5.00
5.006.006.006.008.008.00
10.0010.00
1.001.503.00
8.00
-8.00*
-
8.00*8.00*8.00*8.00*--
--
---
-
PACKINGADVANTAGESAPPLICATION
w w w . i n d s p h i n x . c o m+91 1792 232860 / [email protected]
Routing Aluminium and Copper heat sinks.
Routing Flexi and flexirigid board.
Excellent surface finish for plated through holes.
Efficient chip evacuation.
SCAN TO ORDER
d lD : Ø 1/8" (3.175 mm) Common Shank On Request Shank Dia 3mm
10 tools per pack.50 tools per pack.
ArticleP436
3 FLUTE ROUTER
0.600.701.001.201.501.601.802.002.403.003.175
Tabulated parameters provide guidelines which acts as starting points for optimising speeds and feeds at the user's end.
RECOMMENDED PARAMETERS FOR ROUTING
MATERIAL CUTTING SPEED m/min
FR-4 FR-2 CEM 3 CEM 1 PE PTEF POLYIMIDE Al Cu/BRASS190 - 200 160 - 180 160 - 180 160 - 180 100 - 120 100 - 120 100 - 120 200 - 250 180 - 220
1.201.602.002.403.003.175
0.600.801.00 3
5812151820
22
101834445355
568
810122240526466
6810142535404550
6
Diameter mm
101834445355
568
810122240526466
6810142535404550
7810142535404550
7
35812151820
22
3.003.005.005.007.007.007.009.009.0010.0010.00
IMSPCBFR
PCBPCBCEM POLYIMIDE
FLEXIBLE
PCB
Chip Load microns
P436
FISHTAIL
mm mm
On request : Inch sizes / Special dimensions
: Non stock items / Articles
ØDød
38.00l
5.00-7.50--------
mm/sec
w w w . i n d s p h i n x . c o m+91 1792 232860 / [email protected]
For routing / depaneling PCBs in EMS industries.
For smooth finish.No loose burr on routed edge.Close dimensional control.Run with high feed rates and long tool life.
SCAN TO ORDER
d lD : Ø 1/8" (3.175 mm) Common Shank On Request Shank Dia 3mm
1.40* 7.00
2.00
2.40*
2.50*
1.60
1.80*
8.00
10.50
10.50
8.00
8.00
10 tools per pack.50 tools per pack.
Tabulated parameters provide guidelines which acts as starting points for optimising speeds and feeds at the user's end.
RECOMMENDED PARAMETERS FOR ROUTING FR4
DIAMETER mm
2.00
2.40
1.40
1.60
1.80
SPINDLE SPEEDRPM
30000
25000
38000
32000
30000
CHIP LOAD
HIGH PERFORMANCE DEPANELING ROUTER P650
mm/revX-Y TABLE FEED
m/min in/min
0.059
0.059
0.032
0.050
0.059
1.56
1.56
1.26
1.56
1.56
1.9
1.9
1.2
1.6
1.9
75
75
47
62
75
FISHTAILUPCUTArticle
P650PATTERNDIAMOND
mil/rev
32
32
2.50 24000 0.059 1.56 1.9 7532
20
26
32
mm mm
On request : Inch sizes / Special dimensions
: Non stock items / Articles
PACKINGADVANTAGESAPPLICATION
ØDØd
l38.00
1.50* 8.00
PACKINGADVANTAGESAPPLICATION
w w w . i n d s p h i n x . c o m+91 1792 232860 / [email protected]
Diamond patterened router used for routing contours in PCBs mannual feeding machines.
SCAN TO ORDER
d lD : Ø 1/8" (3.175 mm) Common Shank On Request Shank Dia 3mm
3.175
2.00*
2.40*
3.00*
13.00
13.00
13.00
13.00
PATTERNDIAMOND
10 tools per pack.50 tools per pack.
FISHTAILUPCUTArticle
P628
PIN ROUTER P628
On request : Inch sizes / Special dimensions
: Non stock items / Articles
mm mm
ØDØd
l38.00
Tabulated parameters provide guidelines which acts as starting points for optimising speeds and feeds at the user's end.
SPINDLE SPEEDRPM
RECOMMENDED PARAMETERS FOR ROUTING FR4
DIAMETER mm
X-Y TABLE SPEEDm/min
Z-FEED RATEm/min
2.00 30000 1.0 - 1.4 0.5
2.40 25000 1.0 - 1.4 0.5
3.00 20000 1.0- 1.3 0.5
3.175 20000 1.0 - 1.3 0.5
w w w . i n d s p h i n x . c o m+91 1792 232860 / [email protected]
PCB routing outer and inner contours with very high surface finish requirements.It is especially used for edge trimming on pre- routed slots.
Burr free routing of gold fingers.
Excellent surface finish on pre-routed slots.
SCAN TO ORDER
d lD : Ø 1/8" (3.175 mm) Common Shank On Request Shank Dia 3mm
1.00*1.40*1.50*1.60*1.80*2.00*2.40*2.50
0.60*0.80*1.00*
7.007.007.007.008.507.007.007.00
3.005.005.00
10 tools per pack.50 tools per pack.
FINISHING ROUTER P370
Ød ØD
l38.00
mm mm
On request : Inch sizes / Special dimensions
: Non stock items / Articles
PACKINGADVANTAGESAPPLICATION