pbx aaddmm sdh - ctc u · 2019-12-31 · fmux04a is a fixed design, pdh multiplexer, with 4x e1/t1...
TRANSCRIPT
R
Specifications & design are subject to change without prior notice. Please visit CTC Union website for more details. www.ctcu.com / [email protected]
2020 V1.0
12-1
10101
0101
12
FMUX04A4E1/T1 + 4x GE Fiber Multiplexer
FMUX04A is a fixed design, PDH multiplexer, with 4x E1/T1 plus 4x 10/100/1000Base-T Ethernet switch that provides simultaneous multi-service through dual (1+1) fiber. The fiber optic line is based on 1.25Gbps SFP technology that allows the flexible use of Multimode or Single mode optics and enables support for different wavelengths and distances. The use of bi-directional SFPs maximizes the utilization of fiber optic line and results in saving fiber line costs. The multiplexer can be equipped with optional AC and DC power supplies for redundant operation. With SNMP and Web-based management in the FMUX04A, the administrator can monitor, configure and control both the local and remote device.
Features
Specifications
▪ 4 channels unframed E1/T1 ▪ 4× 10/100/1000Base-TX Ethernet ports ▪ Auto MDI/MDIX ▪ Auto-Negotiation or Force mode ▪ Supports flow control ▪ RS-232 port for system console ▪ One alarm output port, one Order Wire port ▪ Port based VLAN, tag based VLAN & bandwidth control ▪ 2 plug-in SFP slot for optical SFP module ▪ Forward 9K byte packets on Ethernet port ▪ 1+1 fiber protection, less than 50ms
▪ One clear channel RS232 up to 250Kbps(Async) ▪ Supports Digital Diagnostics Monitoring Interface (DDMI) ▪ AIS on signal loss on E1/T1 and fiber port ▪ Loopback test on E1/T1, RS-232, fiber ports ▪ Supports Dying Gasp ▪ Telnet and web based remote configuration ▪ SNMP management ▪ Supports local or remote In-band management ▪ Supports On-Line F/W upgrade (local or remote) by the SNMP manager
E1/T1 Framing: Unframed (transparent)Bit Rate: E1:2.048 Mb/s , T1: 1.544Mb/sLine Code: E1:AMI/HDB3, T1: AMI/B8ZSLine Impedance:E1: Unbalanced 75 ohms (BNC)E1: Balanced 120 ohms (RJ-45) T1: Balanced 120 ohms (RJ-45)Receiver sensitivity: Short haulJitter Performance: According to ITU-T G.823Standard: ITU-T G.644, G.703, G.704, G.706 and G.732Interface Connectors: RJ-45, BNCTest Loops: LLB (Local Loop Back)
RLB (Remote Loop Back) RRLB (Request Remote Loop Back)
OpticalInterface
Bandwidth in optical Line: 1000 MbpsOptical Connector: LC (SFP module)Distance: 20/40/80 Km
OpticalInterface
Optical Wavelength: 1310nm, 1550nm, WDM Tx1310/Rx1550nm (Type A), WDM Tx1550/Rx1310nm (Type B)
Ethernet Interface Type: 100/1000Base-TConnector: 4x RJ-45Standard: IEEE 802.3, 802.3u, 802.3abDuplex modes: full/half
Indication FX1 Link, FX2 link , E1/T1 Mode/Link/Loopback test,Order wire phone indicator , LAN Link/Speed
Power Input AC : 100~240VAC, DC : 18-75 VDCDimensions 248 × 215 × 43mm (D × W × H)Operating 0 ~ 50°C (Operating) Temperature -10 ~ 20°C (Storage)Humidity 10 ~ 90% non-condensingCertifications CE, FCC, RoHS compliantMTBF 75,000 hrs
Application
SmartView
FMUX04A
OrderWire
4E1/T14E1/T1
SDHADM SDHADMOrderWire
PBX
LAN
RS232 clearchannel
RS232 clearchannel
GbE EthernetLAN
GbE EthernetFMUX04A
4E1/T1+GbE over fiber p to p connection Application
Ordering InformationModel Name Description
FMUX04A -AC Standalone FOM with built-in AC PowerFMUX04A -DC Standalone FOM with built-in DC PowerFMUX04A -AD Standalone FOM with built-in AD(AC+DC) Power
4E1/T1 Fiber Multiplexer FM
UX04A
4E1/T1 Fiber Multiplexer
SNMP option only required in one unit of paired linkNote:
10101
0101
R
Specifications & design are subject to change without prior notice. Please visit CTC Union website for more details. www.ctcu.com / [email protected] V1.0
12-2
12
FMUX1001
FMUX101Modularized 16E1/T1 + 4x GbE ManagedFiber Multiplexer
Modularized 16E1/T1 + 4x FE ManagedFiber Multiplexer
The FMUX1001/FMUX101 is a 1U, 19" rack mountable, PDH fiber optic multiplexer that transmits up to 16 channels plus a 10/100/1000Base-T (FMUX1001) / 10/100Base-TX (FMUX101) Ethernet channel over a single fiber optic link. The FMUX1001/FMUX101 chassis supports redundant power and hot swappable design. The AC supplies operate from 100~240VAC while DC supplies operate from 18~60VDC. From the rear of the chassis, one to four hot swappable quad E1 or T1 line cards, serial data communications (V.35, X.21, RS-530) or FXO/FXS voice cards are supported. The standard FMUX1001 configuration may be viewed or set via the front panel LCD/menu keys, serial VT-100 terminal connection, Telnet, web HTTP or SNMP.
Features
Specifications
▪ 1U, 19 (23)” 4-slot chassis ▪ 16 E1 (2.048Mb/s) Multiplexer with 100/1000Mbps Ethernet and RS-232 data (async) Interface (FMUX1001)
▪ 16 E1 (2.048Mb/s) Multiplexer with 10/100Mbps Ethernet and RS-232 data (async) Interface (FMUX101)
▪ RS-232 port for system console ▪ One alarm output port, one Order Wire port ▪ 4x 10/100/1000Base-T Ethernet ports (FMUX1001)
▪ 4x 10/100Base-T Ethernet ports (FMUX101) ▪ SNMP management ▪ LCD plus menu keys for local configuration ▪ Port based VLAN, tag based VLAN & bandwidth control ▪ Telnet and web based remote configuration ▪ 2 plug-in SFP slot for optical SFP module ▪ Forward 1024K byte packets on Ethernet port
Optical Interface Connector SFP - LC
Data rate 1.25G (FMUX1001), 155M (FMUX101)
Bit Error Rate Less than 10-11
Fiber MM 62.2/125μm, 50/125μmSM 9/125μm
Distance MM 2km. SM 15/30/50/80/120kmWDM 20/40/60/80km
Wavelength 1310, 1550nmElectrical Interface
Console, SNMP RJ45Ethernet 4x RJ45
Alarm RJ45
Standards E1:ITU-T, T1:ITU-T, AT&T, ANSI, Ethernet: IEEE 802.3xIndications PWR, Alarm, Phone, ACO, Port, ChannelsPower Input AC module IN : AC 90 ~ 264V, Out : DC 12V
DC module IN : DC 18 ~ 72V, Out : DC 12VPower Consumption < 25W
Dimensions 250 × 438 × 43mm (D × W × H)Weight 3.58 kgTemperature 0 ~ 50°C (Operating), 0 ~ 70°C (Storage)Humidity 10 ~ 90% non-condensingCertification CE, FCCMTBF 50,000 hrs
Application
FMUX1001 orFMUX101 FMUX1001 or
FMUX101
RS232 clear channelGbE or FE LAN
GbE or FE LAN
Order Wire
SmartView
BTS16E1
16E1
RS232 clear channel
Order Wire
Customer Premise
Equipment
1+1 Optical Protection
Central Office (CO)
(CPE)STM1
ADM
Remote 3G BTS Connection Application
Mod
ularized 16E1/T1 M
ultiplexer FMUX1001 &
FMUX101
Modularized 16E1/T1 Managed Multiplexer
R
Specifications & design are subject to change without prior notice. Please visit CTC Union website for more details. www.ctcu.com / [email protected]
2020 V1.0
12-3
10101
0101
12
FMUX1001 & FMUX101 Interface Module
Standards G.711 A-law (separate modules for FXO)
Distance 2km
Bandwidth 64K voice channel
Connector RJ45 x 4 (4 voice channel /per unit)
Standards G.711 A-law (separate modules for FXS)
Distance 2km
Bandwidth 64K voice channel
Connector RJ45 x 4 (4 voice channel /per unit)
Standards ITU-T, E1A
Card Type V.35/ RS-530 (Include X.21 and RS-449)/ RS-232 I/FBit rate n x 64K, n = 1 to 32
V.35 & RS-530 up to 2MbpsRS-232 up to 115.2Kbps (ASYNC)
Line code NRZClock Mode Transparent, Recovery, External (From data port ETC)
Internal (From oscillator)
Standards ITU-T G.703, G.704, AT&T TR-62411,ANSI T1.403
Ports 4 portsFraming Unframed (clear channel)E1 Data rate: 2.048 Mbps ±50 ppm
Line code: HDB3 / AMILine impedance: 120 ohms ±5%, 75ohms ±5%
T1 Data rate: 1.544 Mbps ±50 ppmLine code: B8ZS / AMILine impedance: 100 ohms ±5%
Receive Level Short haul - 15dBConnector RJ-45
Standards ITU-T G.703, G.704, G.706, G.732
Ports 4 portsFraming Unframed ( clear channel )Data rate E1 2.048 Mbps ± 50 ppmLine code E1 HDB3/AMIReceive Level Short haul - 15dBLine impedance E1 75 ohms ± 5%Connector BNC 75 ohms
4x E1 BNC I/F
Related Cables (Please see order information for more details)
V35 RS530 X21RS449
4x E1/T1 RJ45 I/F
4x Data Com I/F
4x FXO I/F 4x FXS I/F
Control Signal CTS always On or follows RTSDSR constantly ON, except during testloops (RS-530 DSR always connect to DTR)DCD constantly ON, except during fiber signal loss
Test Loops Local loop back, Remote loop back, V.54Connector Type Uses HD-68 pin D type Female with adapter
cables
RS232
Ordering InformationModel Name Description
FMUX1001-CH 1U 19” 4-Slot Rack Mount Chassis
FMUX101-CH 1U 19” 4-Slot Rack Mount Chassis
FMUX-AC Chassis Power Module 90~264VAC
FMUX-DC Chassis Power Module 18~72VDC
FMUX-4E1/T1-RJ45 4ch E1/T1 RJ45 interface card
FMUX-4E1/T1-Wire 4ch E1/T1 Wire Wrap interface card
FMUX-4E1/BNC 4ch G.703 E1 BNC interface card
FMUX-V35 V35 interface card with HD68M to 4 x MB34F cable (30cm)
FMUX-530 RS-530 interface card with HD68M to 4 x DB25F cable (30cm)
FMUX-449 RS-449 interface card with one HD68M to 4 x DB37F cable (30cm)
FMUX-X21 X.21 interface card with one HD68M to 4 x DB15F cable (30cm)
FMUX-232/Sync RS-232 Sync card with one HD68M to 4 x DB9F cable (30cm)
FMUX-232/Async RS-232 Async card with one HD68M to 4 x DB9F cable (30cm)
FMUX-4FXO 4 x FXO interface card
FMUX-4FXS 4 x FXS interface card
FMUX-Phone-2W 2 Wires order Wire (connect to analogue Telephone set)
FMUX-Phone-4W 4 Wires order Wire (connect to Ear-Mic set)
FMUX-EXT/CLK External clock interface card
ACDCAA : AC + ACDD : DC + DCAD : AC + DC
A : 4x E1 BNCB : 4x E1/T1 RJ45C : 4x E1/T1 WireD : 4x V.35E : 4x RS-232/AsyncF : 4x RS-530
2W : 2 Wire Phone4W : 4 Wire Phone
1001 : GbE101 : FE
G : 4x X.21H : 4x RS-449 I : 4x FXO
Card TypeFMUX - - -
Power Type Order Wire
J : 4x FXSL : EXT/CLK
M : 4x RS232/Sync
A A B C DC1 10 0 2 W
1001 : GbE Fiber Multiplexer 101 : FE Fiber Multiplexer
FMUX - CH1 0 0 1
Power Module
FMUX A C
I/F Line Card
FMUX V 3 5
Example:Chassis/Power/Line card Only Whole Set
Interface Module
Interface Mod
ule
16E1/T1 Managed Multiplexer
10101
0101
R
Specifications & design are subject to change without prior notice. Please visit CTC Union website for more details. www.ctcu.com / [email protected] V1.0
12-4
12
FMUX1600FMUX80016 or 8x E1/T1 + 4x GbE, ManagedFiber Multiplexer
The FMUX1600/FMUX800 is 1U 19” rack mountable, PDH fiber optical Multiplexer that transmits up to 16/8 E1/T1 + 4 x 10/100/1000Base-T Gigabit Ethernet over a single fiber optic link. The FMUX1600/FMUX800 chassis in available in three different power configurations; single AC, single DC, or AC+DC. The AC supplies operate from 90 ~ 240VAC while DC supplies operate from 18~60VDC. On the rear of the chassis, the BNC model provides 32/16 unbalanced 75 Ohm coaxial connections with BNC connectors while the RJ-45 model provides 16/8 balanced 120 Ohm connections over twisted pair wiring with RJ45 connectors . With two SFP sockets on fiber ports, the FMUX1600/FMUX800 gives you the fiber cabling connector SFP-LC, both multi-mode and single-mode are available as well as BiDi which allows bi-directional transmissions using only a single fiber cable. 1+1 Automatic optical line protection is also supported for the aggregate fiber ports. The standard FMUX1600/FMUX800 configuration may be viewed or set via serial VT-100 terminal connection or SNMP card with web, telnet, and SNMP management
Features
Specifications
▪ Provides 16/8 E1/T1 G.703 transparent transmission over fiber ▪ Provides 4x 10/100/1000 Mbit/s Ethernet Ports and 1x RS232 ch. ▪ Provides one RS232 channel ▪ Loopback test on E1/T1 fiber port ▪ Provides one hotline channel (order-wire) ▪ Supports full/half duplex, 10M/100M/1000M, auto-Negotiation ▪ Forward 10K byte jumbo packets on Ethernet port
▪ Supports 1+1 fiber line protection. Less than 50ms ▪ Complete alarm function and can monitor remote device status ▪ Power combination AC220V and DC-48V for redundant options ▪ Supports RS232 local management; Supports on-line f/w upgrade ▪ Supports Web, Telnet, SNMP management (optional)
Optical Interface Connector SFP- LCData rate 1.25GbpsBit Error Rate Less than 10-11
Distance MM 2km, SM 15/30/50/80/120kmWavelength WDM 20/40/60/80km
Electrical Interface
Connector Console : RS232 / SNMP : RJ45Ethernet : RJ45 (4-port)Alarm : RS232 / Order wire : RJ11
E1 Interface Standards ITU-T G.703, G.704, G.706, G.732Ports 8/16 portsData Rate 2.048 Mbps ± 50 ppmLine Code HDB3/AMIConnector RJ-45 for 120 ohms BNC for 75 ohms
T1 Interface Standards ITU-T G.703, G.704, AT&T TR-62411, ANSI T1.403Ports 8/16 ports
T1 Interface Data Rate 1.544 Mbps ±50 ppmLine Code B8ZS / AMIConnector RJ-45 for 100 ohms
Certification CE, FCC, RoHS compliantStandards ITU-T G.703, G.823 and G.742, ANSI, AT&T, IEEE 803.2,
IEEE 802.3u, IEEE 802.3abIndications Power, Alarm, LBK, RD, LCK, RNG, ACO, Port, channelPower Input 90 ~ 240VAC, 18~60VDCPower Consumption <25W
Dimensions 250 x 438 x 43mm (D x W x H)Weight 3.58kgTemperature 0 ~ 60°C (Operating), -10 ~ 70°C (Storage)MTBF 50,000 hrs
Application
FMUX1600
Remote
1+1 Protection
Local
RS232 clearchannel
RS232 clearchannel
FMUX1600
Order Wire 3G BTS
16 E1/T1
SDHADM
GbE
Order Wire
GbE
16E1/T1
SmartView
Remote 3G BTS connection Application
16E1/T1 Managed
Multiplexer FM
UX1600 & FM
UX80016E1/T1 Managed Multiplexer
R
Specifications & design are subject to change without prior notice. Please visit CTC Union website for more details. www.ctcu.com / [email protected]
2020 V1.0
12-5
10101
0101
12
Ordering InformationModel Name DescriptionFMUX1600B-AD 16x E1 BNC + 4 x 10/100/1000Base-T Ethernet Fiber Multiplexer, build-in AC + DC Power
FMUX1600R-AD 16x E1/T1 RJ-45 + 4 x 10/100/1000Base-T Ethernet Fiber Multiplexer, build-in AC + DC Power
FMUX800B-AD 8x E1 BNC + 4 x 10/100/1000Base-T Ethernet Fiber Multiplexer, build-in AC + DC Power
FMUX800R-AD 8x E1/T1 RJ-45 + 4 x 10/100/1000Base-T Ethernet Fiber Multiplexer, build-in AC + DC Power
FMUX1600-SNMP SNMP Card with 10/100Base-TX Ethernet Port
FMUX800-SNMP SNMP Card with 10/100Base-TX Ethernet Port
FMUX-Phone-2 2 Wires Order Wire
FMUX-Phone-4 4 Wires Order Wire
Model Name DescriptionFMUX1600-SNMP SNMP Card with 10/100Base-TX Ethernet Port
FMUX800-SNMP SNMP Card with 10/100Base-TX Ethernet Port
FMUX-Phone-2 2 Wires Order Wire
FMUX-Phone-4 4 Wires Order Wire
Power Type
FMUX1600–□–□□Example: FMUX1600– B – DC
FMUX–Phone –□Example: FMUX–Phone – 2
E1ConnectorType
SNMP option only required in one unit of paired linkNote:
Option Models
16E1/T1 Managed Multiplexer
16E1/T1 Managed
Multiplexer FM
UX1600 & FM
UX800