participant guide book -...

International Conference on Mechanical Engineering Research and Application

Participant Guide Book “Innovative Research in Engineering for The 21st Century”

2018 23rd-25th October

Santika Premier Hotel Malang - Indonesia

Keynote Speaker:

- A/Prof. Dr. Shahruddin bin Mahzan Universiti Tun Hussein Onn Malaysia

- Prof. Kenji Yasuoka, PhD. Keio University, Japan

- Marco Talice, PhD. PM Squared Engineering, Italy

Supported by:

2

FOREWORD FROM THE ICOMERA 2018 CONFERENCE CHAIR

On behalf of the Organizing Committee of the 1st Conference on Mechanical Engineering Research and Application in

2018 (ICOMERA 2018), we would like to express our gratitude and welcome all ICOMERA 2108 delegates to Malang, a city with cool atmosphere. The first ICOMERA 2018 is an international conference Organized and hosted by Department of Mechanical Engineering, Brawijaya University, and co-organized by Universiti Tun Hussein Onn Malaysia and National Sun Yat Sen University of Taiwan. The event will be held in Malang, Indonesia, in October 23-25, 2018.

As an international academic forum, the conference aims to exchange ideas, knowledge, and expertise in various fields such materials, design, energy conversion, manufacturing, and industrial engineering.

In this international conference, there are various full papers submitted from various regions (Japan, Malaysia, Singapore, Taiwan and Indonesia). All accepted papers that had been reviewed will be published in IOP Conference Series which is

SCOPUS indexed proceeding. Ten best papers will also be published in the special issues of the International Journal of Integrated Engineering which is SCOPUS indexed journal.

Special gratitude for all Committee, Reviewers, Keynote Speakers, and The Rector of Universitas Brawijaya as well as the Dean of Faculty of Engineering for all the hard works, supports and encouragements. We do hope this international

conference will sustainably be hosted and develop the society continuously.

Agung Sugeng Widodo, Ph.D.

3

About The 1st International Conference on Mechanical Engineering Research and Application ICOMERA 2018 The Department of Mechanical Engineering. Faculty of Engineering, Brawijaya University, Malang, Indonesia, are proudly

presenting the 1st International Conference on Mechanical Engineering Research and Application – ICOMERA 2018 with the theme “Innovative Research in Engineering for The 21st Century”. Organised and hosted by Department of Mechanical Engineering, Brawijaya University, and co-organised by Universiti Tun Hussein Onn Malaysia and National Sun Yat Sen University of Taiwan, the event is held in Malang, Indonesia, on October 23-25, 2018. The conference

provide excellent forum for professionals around the globe to share new ideas and information in Mechanical Engineering research and application. With the great pleasure, we present the ICOMERA 2018 Participant Guide Book to give information about keynote abstract, conference schedule, detail of paraller session and venue layout.

All accepted paper has been reviewed thoroughly by blind peer review system by the experts in the related area in order to meet the scientific publication standard. Also, all accepted paper will be published in IOP Conference Series which is SCOPUS indexed proceeding. Ten best papers will also be published in the special issues of the International Journal of Integrated Engineering which is SCOPUS indexed journal.

On behalf of the conference organizer, we would like to thank all of the authors who have spent their tremendous amount of time and effort to contribute their findings, to all of the reviewer which their thorough assessing make the accepted papers have met the international publication standard. The last but not the least, we gratefully acknowledge the committe members, individuals and sponsors for their support and contributions in ICOMERA 2018.

We hope the conference contribute to enrich the research and knowledge. Sincerely yours,

ICOMERA 2018 Committe

Honorary Advisory Board Dr. Ir. Pitojo Tri Juwono, Dean of Faculty of Engineering, Brawijaya University. Dr. Ir. M. Ruslin Anwar, Msi, Vice Dean on General Affair and Budget of Faculty of Engineering, Brawijaya University. Ir. Djarot B Darmadi, MT., PhD, Head of Mechanical Engineering Department, Brawijaya University.

Prof. Ir. I.N.G. Wardana, M.Eng., PhD, Head of Doctorate Program, Mechanical Engineering Department, Brawijaya University. Scientific Committe

Prof. Shahruddin bin Mahzan @ Mohd Zin, Universiti Tun Hussein Onn, Malaysia Prof. Dr. Kenji Yasuoka, Keio University, Japan Prof. Shigeyuki Haruyama, Yamaguchi University, Japan Prof. Chi-Cheng Cheng, National Sun Yat-Sen University, Taiwan

Prof. Kuncoro Diharjo, Sebelas Maret University, Indonesia Prof. Dr. Ir. Djoko Kustono, M.Pd., Malang State University, Indonesia Prof. Ir. ING Wardana, M.Eng, Ph.D., Brawijaya University, Indonesia Prof. Ir. Rudy Soenoko, M.Eng, Ph.D., Brawijaya University, Indonesia

Prof. Ir. Sudjito, Ph.D., Brawijaya University, Indonesia Marco Talice, Ph.D., PM2 Engineering, Italy Wahyu Caesarendra, Ph.D., Nanyang Technological University, Singapore

Oganizing Commitee Conference Chair : Agung Sugeng Widodo, Ph.D. General Co-Chair : Dr. Eng. Moch. Agus Choiron. Secretary Chair : Moch. Syamsul Ma’arif, MT.

Secretary Co-Chair : Nafisah Arina Hidayati, MEng. Finance Chair : Haslinda Kusumaningsih, MEng. Finance Co-Chair : Haedi Oktaviani, ST. Programme Chair : Dr. Eng. Widya Wijayanti.

Promotion Chair : Dr. Slamet Wahyudi. Equipment Chair : Bayu Satriya Wardhana, MEng.

4

TABLE OF CONTENTS

Title 1

Foreword from The ICOMERA 2018 Conference Chair 2

About International Conference on Mechanical Engineering Research and Application 2018 3

Table of Contents 4

Keynote Speakers and Keynote Speech Abstracts 5

Invited Speakers 10

Mechanical Engineering Department, Brawijaya University 13

Venue 14

Conference Program 15

List of Papers 16

Parallel Session I 30

Parallel Session II 31

Parallel Session III 32

5

Keynote Speakers

Keynote Speaker 1

Prof. Madya Dr. Sharuddin bin Mahzan @Mohd Zin

Universiti Tun Hussein Onn Malaysia

Subject Area

Composite, Smart Materials and Structures, Acoustics, Vibration and Condition Monitoring, BioComposites

Biography: Shahruddin bi Mahzan @ Mohd. Zin received the Sarjana Muda Kejuruteraan Mekanikal (B.Eng) from Universiti

Kebangsaan Malaysia in 1999 and Doctor of Philosophy from The University of Sheffield in 2007. He is Associate Professor at Jabatan Kejuruteraan Mekanik (Mechanical Engineering Department) Fakulti Kejuruteraan Mekanikal dan Pembuatan (Faculty of Mechanical and Manufacturing Engineering) and Dekan Pejabat Am Fakulti Kejuruteraan Mekanikal dan Pembuatan (Dean of Faculty of Mechanical and Manufacturing Engineering).

Book and Book Chapter: S.Mahzan (2012) Informatics In Control, Automation And Robotics, Springer Berlin Heidelberg , 679 , ISBN:9783642259913 Shahruddin Bin Mahzan @ Mohd Zin (2009) Impact Damage Detection In A Composite Structure Using Artific ial Neural Network, Composite Materials Technology: Neural Network Applications, CRC Press: Taylor and Francis Group , 112,

ISBN:9781420093322

Latest Publication: Al Emran Ismail, Fazimah Mat Noor, Zaleha Mohamad, Mohd Amran Madlan, M. Zulafif Rahim, M. Rasidi Ibrahim, Sufizar Ahmad, Mohd Nasrull Abdol Rahman, Salihatun Md Salleh, Azmahani Sadikin, Shahruddin Mahzan, Nik Hisyamudin

Muhd Nor (2017) Effect Of Triggering Angles On The Crushing Mechanisms Of Hybrid Woven Kenaf/Aluminum Hollow Cylinders, JOURNAL OF PHYSICS: CONFERENCE SERIES, Institute of Physics Publishing , 12, 012034, ISSN:17426588 How Chui Wei, S.M Salleh, Abdullah Mohd Ezree, I. Zaman, M.H Hatta, B.A. Md Zain, S. Mahzan, M.N.A. Rahman and

W.A.W Mahmud (2017) Improvement Of Automatic Fish Feeder Machine Design , JOURNAL OF PHYSICS: CONFERENCE SERIES , UTHM , 10, 1, ISSN:17426588 Shahruddin Mahzan, Muhamad Fitri and M. Zaleha (2017) Uv Radiation Effect Towards Mechanical Properties Of Natural Fibre Reinforced Composite Material: A Review , IOP: MATERIALS SCIENCE AND ENGINEERING, IOP SCIENCE , 1,

10, ISSN:1757899X M Zaleha, S Mahzan , Muhamad Fitri, K A Kamarudin, Eliza Y, A L Mohd Tobi (2017) Wave Velocity Characteristic For Kenaf Natural Fibre Under Impact Damage, IOP SCIENCE: MATERIAL SCIENCE AND ENGINEERING, IOP SCIENCE , 1, 1, ISSN:1757899X

6

Keynote Speech I Abstracts

Trend of Biocomposite Applications in Engineering

Sharuddin bin Mahzan @ Mohd Zin

Faculty of Engineering and Manufacturing Universiti Tun Hussein Onn Malaysia

Recent advancement in materials and engineering technology have encouraged many scholars from around the world to

investigate and applied materials in engineering applications. Apart from improving its material characteristics, several other areas including the design, type of materials and many others have been explored to suit the demand and requirements of certain engineering applications. This talk is conducted to give some insights on this specific area especially involving bio-natural composites. The introduction of natural fibres and natural based resources has been

highlighted by other scholars. This presentation is mainly focused on the trend of bio composite application especially on the engineering applications. This includes the use of bio composites as sound absorber, vibration absorber and many others. It is hoped that the talks would gave some beneficial information towards implementing natural resources in our daily life.

Keywords: Trend, biocomposite, engineering, application

7

Keynote Speaker 2

Prof. Kenji Yasuoka, Ph.D.

Keio University, Japan

Subject Area Molecular Dynamics, Molecular Simulation, Chemical Physics, Phase Change

Phenomena, High Performance Computing

Biography: Kenji Yasuoka received the Bachelor Degree in Physic from Nagoya University in 1992, Master Degree in Applied Physics Nagoya University in 1994 and Doctor of Philosophy in Applied Physic from Nagoya University in 2007. He is a Professor at Department of Mechanical Engineering, Keio University, Japan. His main interest are Applied and Computational

Mechanics which is focussed in clarifying the phenomena of phase changes (vapor to liquid or liquid to solid) at the microscopic view using molecular dynamics simulation.

Latest Publication: Phase behaviors of deeply supercooled bilayer water unseen in bulk water Kaneko, T., Bali J., Akimoto T., Fransisco J.

S., Yasuoka K.,and Zeng X. C. Proceedings of the National Academy of Sciences of USA 115/ 19, 4839-4844 2018/05 Analysis of three-phase equilibrium conditions for methane hydrate by isometric-isothermal molecular dynamics simulations Yuhara, D., Brumby, P. E., Wu, D., Sum, A. K., Yasuoka, K. J. Chem. Phys. 148, 184501 (9 pages) 2018/05 Density functional theory study of atomic and electronic properties of defects in reduced anatase TiO2 nanocrystals

Morita K., Yasuoka K. AIP Advances 8, 035119 (14 pages) 2018/03 Detection of Anomalous Dynamics for a Signle Water Molecule Tomobe, K., Yasuoka, K. J. Chem. Theory Comput. 14/ 3, 1177-1185 2018/03 Critical test of isotropic periodic sum techniques with group-based cut-off schemes Nozawa, T., Yasuoka, K., Takahashi,

K. Z. Scientific Reports 8, 4185 (9 pages) 2018/03

8

Keynote Speaker 3

Marco Talice, Ph.D. PM Squared Engineering, Italy

Subject Area Molecular Dynamics, Molecular Simulation, Chemical Physics, Phase Change

Phenomena, High Performance Computing

Biography: Marco Talice received Doctor of Philosophy in Mechanical Engineering from Università degli Studi di Cagliari in 1998. He was a visiting academic in UNSW (Australia) from 1998-2010. Joined KARALIT as Senior Engineer from 2010-2016 he then co-founded PM Squared Engineering, a company which provide all need in CFD simulations especially for

computational physics and numerical methods in 2017. His main interest are on combustion and innovative mathematical tools, such as immersed boundaries methods.

Latest Publication: A Hybrid Immersed Boundary CFD Approach to Oil and Gas Applications, M. Mulas, M. Talice, and A.N. Grozescu. Proceedings of ASME Turbo Expo 2013: Turbine Technical Conference and Exposition 2013

Efficient Parallel Fully Coupled Solver for MuIticomponent Turbulent Reacting Flows, T. Belmrabet, M. Talice, G. Delussu, S. Hanchi. Computational Fluid Dynamics Review 2010/07 Combustion Analysis Using Roe's Scheme and the Spalart-Allmaras Model, T. Belmrabet, M. Talice, G. Delussu, S. Hanchi 2009/11

An Implicit Parallel Fully Compressible Roe Based Solver for Subsonic and Supersonic Reacting Flows, T. Belmrabet, M. Talice, G. Delussu, S. Hanchi, Computational Fluid Dynamics, 2008 2009/01

9

Keynote Speech III Abstracts

Recent developments in CFD: an Immersed Boundary Method

for Compressible Fluid Dynamics

Marco Talice PMSQUARED Engineering s.r.l.s v. S. Sonnino, 99 Cagliari, Italy

Computational Fluid Dynamics (CFD) was “officially” born at the end of the last century (1960s) when simple (in todays view) linear potential problems have been solved via the use of computers. From that moment on, thanks to the advance in numerical methods on one side, and to the fast growth of computing power on the other side, CFD has been used to

tackle more and more complex problems both from “physics” and “geometric” standpoints. Grid generation (the first step in the CFD work-flow) has soon become a very “expensive” part of the simulation process. In the last decade of the past century, the idea of Immersed Boundary (firstly developed by Vieceli and then by Peskin for heart simulation) was re-discovered. As the name suggests, all complexities related to the grid generation process are de facto taken away and

the geometry of interest is instead simply “immersed” into a Cartesian grid. In order to still being able to properly describe the mutual interaction between the fluid and the immersed body, “something” must then be done to link together these two separated world (the body and the Cartesian grid). This work will present the development of one “flavor” of this class of numerical techniques into the compressible flow solver IBraptor.

Keyword: CFD, Immersed boundary layer, compressible, fluid dynamics.

10

Invited Speakers

Dr. Samsudin Anis Department of Mechanical Engineering, Universitas Negeri Semarang.

Subject Area: Bioenergy, Renewable Energy, Heat and Mass Transfer, Thermo Fluid

Biography: Samsudin Anis received the Bachelor Degree in 2000 and Master Degree in 2003 in Mechanical Engineering from Gadjah Mada University. His Doctoral Degree was received from University Sains Malaysia in 2017. He is a Lecturer at Department of Mechanical Engineering, Universitas Negeri Semarang.

Latest Publication: Study on kinetic model of microwave thermocatalytic treatment of biomass tar model compound, Bioresource technology

151, 183-190 | vol: | issue : | 2014.Thermocatalytic treatment of biomass tar model compounds via radio frequency, Bioresource Technology 136, 117-125 | vol: | issue : | 2013. Upgrading producer gas quality from rubber wood gasification in a radio frequency tar thermocatalytic treatment reactor Bioresource technology 150, 328-337 | vol: | issue : | 2013.

Tar reduction in biomass producer gas via mechanical, catalytic and thermal methods: A review Renewable and Sustainable Energy Reviews 15 (5), 2355-2377 | vol: | issue : | 2011. Teknik Produksi Mesin Industri, Jakarta: Direktorat Pembinaan Sekolah Menengah Kejuruan | vol: | issue : | 2008.

11

Dr. Tribidasari A Ivandini Department of Chemistry, Faculty of Mathematics and Natural Sciences, Universitas Indonesia.

Subject Area: Electrochemistry, Diamond Electrochemistry, Sensors and Biosensors, Electrocatalysis

Biography: Dr. Ivandini Tribidasari Anggraningrum is a member of the teaching and research staff at Department of Chemistry, Faculty of Mathematics and Science, Universitas Indonesia, since 1997. She was born in Jakarta on January 29th, 1970. She received her bachelor and magister degrees in 1993 and 1996, respectively, from Universitas Indonesia. In 2003 she accomplished her doctoral degree at The University of Tokyo, Tokyo, Japan. Between 2003 and 2007 she performed

post-doctoral research at the Department of Chemistry, Keio University, Tokyo, Japan with JSPS fellowship during 2004-2006. Up to the present time she is still performing research collaboration with Keio University. Her research interests are mostly concerning electrochemistry of diamond, including its development for sensors and biosensors, electrocatalytics, and waste-water treatment. She has published circa 50 scientific papers in highly

respectable journals and conference proceedings, such as Analytical Chemistry, Physical Chemistry Chemical Physics, Sensors Actuators B: Chemicals, and Diamond Related Materials. She also holds some patents under European and Japan Patents. In 2012, she received an award from Universitas Indonesia as the most productive researcher in Universitas Indonesia.

(http://staff.ui.ac.id/ivandini.tri)

Publication: Anodic stripping voltammetry of gold nanoparticles at boron-doped diamond electrodes and its application in immunochromatographic strip tests, Talanta 134 (2015) 136-143. Electrochemical Oxidation of Proteins at Conductive Diamond Electrodes, J. Electroanalytical Chemistry 612, 201-207,

Electrochemical Detection of Free Chlorine at Highly Boron-Doped Diamond Electrodes, J. Electroanalytical Chemistry 612, 29-36. Anodic Stripping Voltammetry of Inorganic Species of As3+ and As5+ at Gold-Modified Boron Doped Diamond Electrodes, J. Electroanal. Chem., 615, 145-153.

The importance of H-termination for electrochemical analysis by using diamond electrodes, Chemical Sensor 21, 139-141.

12

Wahyu Caesarendra, PhD. School of Mechanical and Aerospace Engineering, Nanyang Technological University, Singapore

Subject Area: Condition monitoringSignal processingPattern recognitionMachine learning and Mechatronic

Biography: Wahyu Caesarendra was born in Jakarta, Indonesia on January 31st, 1982. He received Bachelor of Engineering degree from Diponegoro University, Indonesia in 2005. He worked in automotive and electrical company prior to join Diponegoro University as a Lecturer in 2007. He received New University for Regional Innovation (NURI) and Brain Korea 21 (BK21)

scholarships for Master study in 2008 and obtained his Master of Engineering (M.Eng) degree from Pukyong National University, South Korea in 2010. In 2011, Wahyu Caesarendra was awarded of University Postgraduate Award (UPA) and International Postgraduate Tuition Award (IPTA) from University of Wollongong. He received Doctor of Philosophy (Ph.D) degree from University of Wollongong in 2015. He published more than 30 research articles in Journals and

Conference proceedings. One of them was being the top 25 most cited paper in Mechanical Systems and Signal Processing Journal. He has developed skills and experience in scholarly research, teaching and learning activit ies. He is currently Postdoctoral Fellow in Rolls-Royce@NTU Corp Lab, School of Mechanical and Aerospace Engineering, Nanyang Technological University, Singapore (https://www.researchgate.net/profile/Wahyu_Caesarendra).

Latest Publication: C Andriani, W Caesarendra, T Tjahjowidodo, T Wijaya, BK Pappachan, 2018. Modal Analysis of Replica Boss Hole During the Deburring Process in Aerospace Manufacturing Industry, MATEC Web of Conferences 159, 02012. DB Wibowo, A Suprihanto, W Caesarendra, M Ariyanto, 2018. Digital integrated instrument for measuring BMI and comparing to the ideal BMI for age as a guidance for Indonesian military recruitment, MATEC Web of Conferences 159,

02009. FT Putri, M Ariyanto, W Caesarendra, R Ismail, KA Pambudi, 2018. Low Cost Parkinson’s Disease Early Detection and Classification Based on Voice and Electromyography Signal, Computational Intelligence for Pattern Recognition, 397-426

W Caesarendra, B Kosasih, T Tjahjowidodo, M Ariyanto, LWQ Daryl, 2018. An online condition monitoring system implemented an internet connectivity and FTP for low speed slew bearing, Journal of Physics: Conference Series 1007 (1), 012002 IS Aisyah, W Caesarendra, A Suprihanto, 2018. Design and Testing of UMM Vertical Ball Mill (UVBM) for producing

Aluminium Powder, Journal of Physics: Conference Series 1007 (1), 012063

13

MECHANICAL ENGINEERING UNIVERSITY OF BRAWIJAYA

Overview Mechanical Engineering is one of the departments in the Faculty of Engineering, University of Brawijaya which has established in 1963 in Malang City, East Java, Indonesia. Mechanical Engineering in University of Brawijaya has study programs for bachelor, master and doctoral degrees. Bachelor study programs are divided into four concentrations, there are construction engineering, manufacturing engineering, energy conversion engineering, and material engineering. Master and doctoral study programs are divided into three specializations, there are energy conversion engineering, manufacturing industry engineering, and material and manufacturing engineering. Some of the facilities that support the academic activities in Mechanical Engineering are library, thirteen laboratories and two studios. The laboratory consists of Manufacturing Process Laboratory, Material Testing Laboratory, Metal Casting Laboratory, NC / CNC Laboratory, Combustion Engine Laboratory, Fluid Machines Laboratory, Refigeration Laboratory, Basic Machine Phenomenon Laboratory, Industrial Metrology Laboratory, Solar Power and Alternative Energy Laboratory , Mechanical Central Laboratory, and Computer Laboratory and 2 studios namely Mechanical Drawing Studio and Design and System Engineering Studio.

Vision “In 2020, Mechanical Engineering Department of Brawijaya University will be a center of education, research, and community service in the field of mechanical engineering which has advantages and benefits for the public, national, Southeast Asian, and Asian communities supported by human resources, infrastructure, adequate facilities, and conducive academic atmosphere.”

Mission 1. To Organize an effective, efficient, accountable and sustainable organization and administration of

education. 2. To Organize education and teaching that ensures quality and relevant output to the needs of Mechanical

Engineering graduates at the local, national, Southeast Asia, and Asia with an academic atmosphere that is in line with national and international standards.

3. To Conduct research in the field of mechanical engineering. 4. To Organize community service with the application of research results and studies in the field of

mechanical engineering.

14

Hotel Santika Premier Malang Jalan Letjen Sutoyo No.79,

Malang – East Java

Hotel Santika Premier 1st Floor Layout

Note: BAM 1 = Ballroom Majapahit 1; BAM 2 = Ballroom Majapahit 2; BAM 3 Ballroom Majapahit 1

Hotel Santika Premier 2nd Floor Layout

15

CONFERENCE PROGRAM

Tuesday, 23th October 2018

Time Programs Venue

12.00-20.00 Registration

- On the spot conference registration - Bromo Adventure registration

- Batu Trip registration

Front of Majapahit Room

Wednesday, 24th October 2018

Time Programs Venue

07.00-08.00 Registration Front of Majapahit Room.

08.00-10.00 Parallel Session I Majapahit Room 2a, 2b, 3a and 3b. Lontar Room 1 and 2.

10.00-10.15 Coffee Break

10.15-12.15 Parallel Session II Majapahit Room 2a, 2b, 3a and 3b. Lontar Room 1 and 2.

12.15-13.00 Lunch Break

13.00-13.30 Keynote Speech I A/Prof. Dr. Shahruddin bin Mahzan

Majapahit Room.

13.30-14.00 Keynote Speech II Prof. Kenji Yasuoka, PhD.

Majapahit Room.

14.00-14.30 Keynote Speech III Marco Talice, PhD.

Majapahit Room.

14.30-15.00 Coffee Break

15.00-17.00 Parallel Session III Majapahit Room 3a and 3b. Lontar Room 1 and 2.

17.00-18.30 Break

18.30-20.00 Gala Dinner and Closing Ceremony - Performing Art

- Chair speech - Head of ME speech

- Best Paper Announcement - Dean speech and Closing

- Dinner

Majapahit Room.

Thursday, 25th October 2018

Time Programs Venue

00.00-12.00 Trip to Bromo (additional surcharge apply) Mount Bromo

09.00-19.00 Trip to Batu (additional surcharge apply) Museum Angkut (Transportation Museum)

and Batu Secret Zoo

16

List of Paper International Conference on Mechanical Engineering Research and Application 2018

Keynotes Speaker and Invited Speaker

ICOMERA-KS-01 Sharuddin bin Mahzan @ Mohd Zin

Trend of Biocomposite Applications in Engineering Faculty of Engineering and Manufacturing Universiti Tun Hussein Onn Malaysia

ICOMERA-KS-02 Kenji Yasuoka Molecular Simulation Study in the Field of Thermal

Engineering

Mechanical Engineering Department, Keio University

ICOMERA-KS-03 Marco Talice Recent developments in CFD: an Immersed Boundary Method for Compressible Fluid Dynamics

PM SQUARED Engineering s.r.l.s

ICOMERA-INV-01 Samsudin Anis Potential of Microwave Heating for Wastes Processing

Department of Mechanical Engineering, Universitas Negeri Semarang.

ICOMERA-INV-02 Tribidasari A Ivandini1 and Yasuaki Einaga2

Potency of Boron-Doped Diamond for an Application in Urine Fuel Cell

1Department of Chemistry, Faculty of Mathematics and Natural Sciences, Universitas Indonesia. 2Department of Chemistry, Faculty of Science and Technology, Keio University, Japan

ICOMERA-INV-03 Wahyu Caesarendra1, Iis Siti Aisyah2, A. Fauzan

H.S.2, Ali Syaifullah2, Mochammad Syamsul Ma’arif3

The Role of Bio-lubricant on the Characterization of Ti-alloy Machining

1School of Mechanical and Aerospace Engineering, Nanyang Technological University, Singapore. 2Department of Mechanical Engineering, Muhammadiyah University of Malang. 3Department of Mechanical Engineering, Brawijaya University.

17

Topic: Materials

ICOMERA-04 Ridhwan Haliq, Ammar Farhan Rayudi,

Abdi Suprayitno

The Effect of Filler Composition and Shape to Sound Capability Insulation and Modulus Elasticity Natural

Fiber Galam Wood (Melaleuca Leucadendra) - Polyester)

Mechanical Engineering Department, Institut

Teknologi Kalimantan

ICOMERA-10 Wahyu Purwo Raharjo, Rudy Soenoko Effect of Chemical Treatment on Wettability of Zalacca Fibres as Composite Reinforcements

Mechanical Engineering Department, Universitas Negeri Surakarta

ICOMERA-21 K M T Negara, I N G Wardana, D Widhiyanuriyawan, and N Hamidi

The Role Of The Slope On Taro Leaf Surface To Produce Electrical Energy

Mechanical Engineering Department, Samawa University

ICOMERA-26 Andi Idhil Ismail, Ridwan Haliq,

Muhammad Jamil

On the crystallization of Mg-based bulk metallic glass

(BMG)

Mechanical Engineering Department, Institut

Teknologi Kalimantan

ICOMERA-27 M. Azham Azmi, S. Mahzan, S. Ahmad, S.M. Salleh, H.A. Rahman, M.A.

Choiron, A. Ismail, H. Taib

Vibration Exposure of Polydimethylsiloxane (PDMS) Reinforced Silica (SiO2): Comparison of Different

Source of Silica (SiO2) as Filler

Faculty of Mechanical and Manufacturing Engineering, Universiti Tun Hussein Onn, Malaysia

ICOMERA-28 H.A. Rahman, K.H. Ng, S. Ahmad, H.

Taib, A. Ismail, S.M. Salleh, S. Mahzan, A. Muchtar

Influence of microstructure on the electrochemical

behaviour of LSCF-SDCC

Faculty of Mechanical and Manufacturing

Engineering, Universiti Tun Hussein Onn, Malaysia

ICOMERA-30 S.F. Mohammad , S. Ahmad, H.A. Rahman, H. Taib, A. Ismail, S.M. Salleh, S. Mahzan

Comparative Characterization on Structural Properties of Calcined Sm0.5Sr0.5CoO3−δ - Sm0.2Ce0.8O1.9 Carbonate as Potential Composite Cathode for SOFC


ICOMERA-31 E.M. Yusup, Djarot B Darmadi, S. Mahzan, M.A.H. Kamaruddin

Mechanical Properties of Natural Fiber Reinforced Polymer using Mold Casting Method


ICOMERA-32 Sumarji, Imam Sholahuddin, Dedi Dwi

Laksana, Ahmad Syuhri,

Yanuar Aditya

Effect of Steam Pre-treatment of Bagasse as Fiber Reinforcement SCG Composite

Mechanical Engineering Department, Jember University

ICOMERA-33 I.Azzura, M.S.N. Farhana, M.N. Lokman, S.Mahzan, S. Ahmad, H. Taib,

H.A. Rahman, S.M. Salleh

Identification Corrosion Hydrogen Attack on Carbon Steel Using Magnetic Particle Inspection (MPI)


18

Topic: Materials (continued)

ICOMERA-42 Sunardi, Moh. Fawaid, Rina Lusiani,

Setyo Bayu Aji Kesworo and Teguh Dwi Widodo

The Effect of Wood Sawdust Mesh Combination on

Mechanical Behaviour of Particle Board

Mechanical Engineering Department, Universitas

Sultan Ageng Tirtayasa

ICOMERA-05A Pandri Pandiatmi, Emmy Dyah, Samsul Watoni

Optimization of Bending Strength of Polyester Composite Reinforced by Hibiscus Tree Bark Fiber

and Fly Ash Filler

Mechanical Engineering Department, Mataram University

ICOMERA-07A Ira Kusumaningrum, Mualifi Usman Effect of more anodic metal addition of zinc on cathode protection of lead-iron-zinc anode on the

corrosion rate

Study Program of Mechanical Engineering, Darul ‘Ulum University

ICOMERA-12A Sutrisno, Sutomo, Sudarno, and Tomi Tristono

Study on Mechanical Properties of Composite Geomaterial Powder Waste Tiles and Glass Fiber

Faculty of Engineering, Universtas Merdeka Madiun

ICOMERA-14A Pandri Pandiatmi, Emmy Dyah, Sastriawan

Optimization of Bending Strength of Polyester Composite Reinforced by Hibiscus tiliaceaus Tree Bark with Rice Husk Filler using Response Surface

Method

Mechanical Engineering Department, Mataram University

ICOMERA-15A Firman Mangasa Simanjuntak, S Chandrasekaran, F Gapsari and T Y Tseng

Switching and synaptic characteristic of AZO/Zn/ITO valence change memory device

Advanced Institute for Materials Research Device/System, Tohoku University, Japan

ICOMERA-19A Purnomo, Putu Hadi Setyarini, Dini

Cahyandari

Potential Natural Fiber-Reinforced Composite for

Biomedical Application


Muhammadiyah Semarang, Indonesia

ICOMERA-20A Andita N.F Ganda, Ching-Yuan Su The parametric study on anti-corrosion properties produced by electrochemically exfoliated

Department of Mechanical Engineering, State University of Surabaya

ICOMERA-25A Ardi Rofiansyah, Masato Tominaga, Fredy Kurniawan

Response of SWCNTs/KPG5-modified Carbon Electrode on Dopamine, Uric Acid and Ascorbic Acid

Chemistry Department, Faculty of Sciences, Institut Teknologi Sepuluh Nopember

ICOMERA-26A Y R A Pradana, A Aminnudin, H Suryanto, D Z Lubis

Hardness distribution and impact toughness of carburized steel welded by SMAW

Mechanical Engineering Department, Malang State University

19

Topic: Materials (continued)

ICOMERA-41 Susilo Adi Widyanto, Paryanto,

Sukamta, Agus Suprihanta

Dimensional Investigation of Corrugated Steel Silo with

4650 tons Storage Capacity

Mechanical Engineering Department, Diponegoro University

ICOMERA-101 Wahyono Suprapto Effect Recycled Aluminium Structures of Metallurgical

and Melt Efficiency

Mechanical Engineering Department, Brawijaya University

ICOMERA-108 Tjuk Oerbandono Characteristic of Tensile and Impact Strength of Fibre-powder Reinforced under Uni-directional loading


ICOMERA-115 Denny Widhiyanuriyawan, Imam Mawardi Maksum, Redi Bintarto

Effect of Temperature and Mass Ratio (NH4F:SnCl2.2H2O) in Production of Fluorine Doped Tin Oxide (FTO) Conductive Glass


ICOMERA-118 Teguh Dwi Widodo Effect Of Alkalization Treatment on The Tensile Strength and Interface Character Matrix-Fiber of Bambu Petung (Dendrocalamus Asper) Reinforced Polyester Resin Composite


ICOMERA-125 Femiana Gapsari, Putu Hadi Setyarini, Ervinda N.

The Effect of Electrodeposition Current to Tinplate with Chitosan


ICOMERA-124 Winarto Selectivity of carbon nanotubes under an electric field on transfering water-alcohol mixtures


20

Topic: Energy Conservation

ICOMERA-05 Illa Rizianiza, Devy Setiorini S, Alfian Djafar

The effect of the angle of attack on the electric power generated on prototype of the horizontal axis wind turbine

Mechanical Engineering Department, Institut Teknologi Kalimantan

ICOMERA-09 La Ode Ahmad Barata, Takahiro

Kiwata, Sunichi Mizukami, Takaaki Kono

Numerical Study on unstable oscillation phenomena of

finite height rectangular prism below critical side ratio

Kanazawa University

ICOMERA-11 Syaiful, Nazaruddin Sinaga, Bambang

Yunianto, MSK. Tony Suryo Utomo

Comparison of Thermal-Hidraulic Performances of

Vortex Generators Mounted on Heated Plate: Experimental Study and Flow Visualization

Mechanical Engineering Department, Diponegoro

University

ICOMERA-12 Faqih Fatkhurrozak, Syaiful Effect of Diethyl Ether (DEE) on Performances and Smoke Emission of Direct Injection Diesel Engine

Fueled by Diesel and Jatropha Oil Blends with Cold EGR System


ICOMERA-14 Caturwati Ni Ketut, Agung Sudrajad, Heri Haryanto

Improved performance of CS 100 l LPG fuel generator with the addition of biogas

Mechanical Engineering Department, Universitas Sultan Ageng Tirtayasa

ICOMERA-15 Nazaruddin Sinaga, Bambang

Yunianto, Syaiful

On the Effect of Addition of 1,2-Propylene Glycol

Composition on Power and Torque of an EFI

Passenger CarFueled with Methanol-Gasoline M15


University

ICOMERA-16 Rudi Hariyanto, Sudjito Soeparman, Denny W, Mega N S

Numerical and Experimental Study on the Savonius Rotor Performance with The Gap Width Variations of

Ventilation in Middle Blades

Mechanical Engineering Department, Merdeka University

ICOMERA-18 Widya Wijayanti Thermodynamic Characteristics of Gases in the Hydrate


ICOMERA-23 Ena Marlina, ING Wardana, Lilis Yuliati, W. Wijayanti

The effect of fatty acid polarity on the combustion characteristics of vegetable oils droplets

Mechanical Engineering Department, University of Islamic Malang

ICOMERA-24 Yunita Nur Afifah Analysis of Unsteady Magnetohydrodynamics (MHD) Nano Fluid Flow Past a Sliced Sphere

Mechanical Engineering Department, Universitas Maarif Hasyim Latif Sidoarjo

21

Topic: Energy Conservation (continued)

ICOMERA-34 Nazaruddin Sinaga, Mohammad Tauiviqirrahman, Arif Rahman Hakim, Eflita Yohana

Effect of Texture Depth on The Hydrodynamic Performance of Lubricated Contact Considering Cavitation


ICOMERA-44 Raharjo S, Muryanto S, J Jamari, A P

Bayuseno

Optimization and Controlling of FeCO3 Scale

Deposition on the Piping System with Laminar Flow and in The Presence of Zeolite Adsorbance

Department of Mechanical Engineering,

Muhammadiyah University in Semarang, Indonesia

ICOMERA-45 Subuh Isnur Haryuda, I Wayan Susila, Indra Herlamba Siregar, Aris Ansori

Power Control of Grid-Connected Photovoltaic-Wind Turbine-Buoy Conversion Energy Wave Hybrid

System

Mechanical Engineering Department, Universitas Negeri Suarabaya

ICOMERA-52 Budi Santoso, Dominicus Danardono Dwi Prija Thajana and Guntur Prakoso

Visualization Study of Air-Water Two-Phase Flow Pattern in Upward Vertical Flow of Square Channel

Mechanical Engineering Department, Engineering Faculty, Sebelas Maret University

ICOMERA-60 Emi Yuliarita, Lies Asiyah, Nur Allif Fathurrahman, Maymuchar, Nanang

Hermawan and Riesta Anggarani

Comparison of Synthetic and Plant Extract Antioxidant Additives on Biodiesel Stability

Fuel and Lubricant Research Group Research and Development, Center of Oil and Gas Technology

“LEMIGAS”

ICOMERA-62 Sudirman Syam, Soedjito Soeparman, Denny Widyanuriawan, Slamet Wahyudi and Sri Kurniati

A New Design of Magnetic Gear Axial using a Rectangular NdFeB Magnetic Layer

Electrical Engineering Department, Science and Engineering Faculty, University of Nusa Cendana

ICOMERA-75 L Aisyah, S A Bethari, C S Wibowo, N

Hermawan, D U Alwi, D Rulianto and R Anggarani

Water content in biodiesel for diesel fuel blends:

measurement using centrifuge and coulometric titration method

Fuel and Lubricant Research Group

Research and Development Center of Oil and Gas Technology “LEMIGAS”

ICOMERA-77 S. Tursiloadi, E. Agustian, A. Sulaswatty, N. Rinaldi and Sudiyarmanto

One-Pot Conversion and Separation of Methyl Eugenol by Vacuum Fractionation

Research Center for Chemistry, Indonesian Institute of Sciences

ICOMERA-08A Made Ery Arsana, I G N Wijaya

Kusuma, Made Sucipta, I Nyoman Suamir

Thermodynamic Analysis of Two Phase Ejector as

Expansion Device With Dual Evaporator Temperature on Split Type Air-Conditioning Systems

Study Program of Mechanical Engineering, Bali

State Polytechnic

ICOMERA-09A Muhamad Fakhrurozi Effect of plastic type and temperature on fuel

produced by pyrolysis method

Universitas Darul Ulum

22


ICOMERA-16A I Nyoman Suamir, M E Arsana, and K M Tsamos

Experimental Study on the Influence of Integral Hydrocarbon Display Cabinet to its Temperature and Energy Performance

Mechanical Engineering Department, Bali State Polytechnic

ICOMERA-24A I M Rasta, I N Suamir Study on Thermal Properties of Bio-PCM Candidates

in Comparison with Propylene Glycol and Salt Based PCM for sub-Zero Energy Storage Applications

Mechanical Engineering Department, Bali State

Polytechnic

ICOMERA-33A Sukarni Thermogravimetric Analysis and the Fitting Model Kinetic Evaluation of Corn Silk Thermal Decomposition

under Inert Atmosphere

Mechanical Engineering Department, Universitas Negeri Malang

ICOMERA-102 Slamet Wahyudi, Wardana, Widodo A Shear Stress Analysis on Synthesis and Releases of Nitric Acid from HUVEC


ICOMERA-104 Sugiarto, Nurkholis Hamidi The Role of Pre-Destilation Fermentation in Increasing of Nilam (Pogostemon cablin Benth) Oil Productivity


ICOMERA-106 Agung Sugeng W and Awaluddin Flow characteristic of horizontal-vertical upward air-water with 45° elbow


ICOMERA-110 Purnami, I.N.G Wardana, and Enrico Gultom

Effect of Rhodium (III) Sulphates and Clove Oil Addition to Combustion Characteristic of Jatropha Oil

Droplet.


ICOMERA-113 Sudjito, Sarip, Lilis Yuliati, Moch. Agus Choiron

Experiment on Novel Design of Tapered Shape Heat Pipe


ICOMERA-114 Djoko Sutikno, Rudy Soenoko, Sudjito Soeparman, Slamet Wahyudi, Francisca Gayuh Utami Dewi

Performance Characteristics Of The Low Head Cross Flow Turbine Using Nozzle Roof Curvature Radius Centered on Shaft Axis


ICOMERA-116 Nurkholis Hamidi, Purnami, Widya Wijayanti, Rizal Fahmi

Pressure effect in droplet combustion of blended fuel of etanol and kemiri sunan (Reutealis Trisperma (blanco) airy shaw) biodiesel


23


ICOMERA-119 Mega Nur Sasongko Droplet Combustion Characteristic of biodiesel produced from Waste Cooking Oil


ICOMERA-120 Lilis Yuliati Droplet combustion characteristics of castrol oil biodiesel - ethanol blended.


ICOMERA-121 Eko Siswanto, A. Zainur Rifan, Purnami, D. Widhiyanuriyawan, Djarot B. Darmadi

Effect of Porosity to Temperatrure Profile Spectrum and Heat Transfer on Porous Media under Saturated Vapor Flow


ICOMERA-127 Haslinda Kusumaningsih, Lilis Yuliati, Rudianto Raharjo, Ragang Aji

Effect of Reactant Inlet Direction to Combustion Characteristic in Circular Disk Combustor


24

Topic: Manufacturing

ICOMERA-02 Redi Bintarto, Nurkholis Hamidi, Rudianto

Raharjo, Teguh Dwi Widodo

Effect of Machining Parameters on the Surface

Roughness of Dolomite Cups

Mechanical Engineering Department, Brawijaya

University

ICOMERA-03 Rudianto Raharjo, Haslinda Kusumaningsih, Teguh Dwi Widodo, Redi Bintarto, Maya Widiasesanti

Enhancement of Tongue Depressor Hardness by Heat Treatment and Shot Peening


ICOMERA-08 Imam Kusyairi, Helmy Mukti Himawan, Moch. Agus Choiron, Yudy Surya Irawan

Manufacture of Origami Pattern Crash Box Using Traditional Investment Casting Method

Mechatronic Engineering, Polytechnic of Malang

ICOMERA-17 Khairul Anam, Anindito Purnowidodo The Effect of Shot Peening Configurations on Residual Stress of Aluminium 5052


ICOMERA-19 Khairuddin Mahalil, Erween Abd Rahim, Zazuli Mohid

Comparison Between Dry, MQL, and Cryogenic Cooling Technique on Surface Integrity of Burnished

Surface

Machinery Technology Centre, SIRIM Berhad

ICOMERA-20 Khairuddin Mahalil, Erween Abd Rahim,

Zazuli Mohid

Performance Evaluation of Sustainable Coolant Techniques on Burnishing Process

Machinery Technology Centre, SIRIM Berhad

ICOMERA-25 Mochamad Choifin, Wiji Lestariningsih Design And Development Of Microrontroller Battery

Filling Control System Arm Cortex M0-Nuc 120 On Axial Axis Wind Turbine Type

Mechanical Engineering DepartmentUniversitas

Maarif Hasyim Latif Sidoarjo

ICOMERA-29 H.M.Y. Ainul, S.Mahzan, S. Ahmad, H. Taib, H.A. Rahman, A. Ismail, S.M. Salleh

Evaluation of Varies Model Order in GA-optimised Parameter Estimation of Toothbrush Rig System


ICOMERA-35 M Pramudia, T Prasetyo, M K Umami, R Alfita, R V Nahari, Teguh D Widodo

and

Rudianto Raharjo

The effect of steel ball diameter variation in dry shot peening process on surface roughness and corrosion

rate of AISI 316L implant material

Mechanical Engineering Department, Trunojoyo University

ICOMERA-37 H Suryanto, AW Rahmawan, Solichin, RT

Sahana, M Muhajir, U Yanuhar

Influence of Carrageenan on the Mechanical Strength

of Starch Bioplastic Formed by Extrusion Process


Negeri Malang

25

Topic: Manufacturing (continued)

ICOMERA-38 H Suryanto, F A Kharismawan, Solichin, AW Rahmawan, RT Sahana, M Muhajir, U Yanuhar

Influence of Nanoclay on Thermal Decomposition of Biocomposite Matrix Starch/Carrageenan Blend


ICOMERA-39 Mochamad Arif Irfa’i, Dzulkiflih, Diah Wulandari, Andita N.F Ganda and

Supardiyono

The effect of pouring temperature on the porosity of sand casted Al – Si alloy

Mechanical Engineering Department, State University of Surabaya

ICOMERA041 Susilo Adi Widyanto, Paryanto, Sukamta,

Agus Suprihanto

Dimensional investigation of corrugated steel silo with

4650 tons storage capacity


University

ICOMERA-70 Gandjar Kiswanto, Wina Libyawati Fundamental Aspects in Designing Vibration Assisted Machining: A Review

Department of Mechanical Engineering, Universitas Indonesia, Depok, Indonesia

ICOMERA-71 Widia Setiawan, Djarot B. Darmadi, Wahyono Suprapto, Rudy Soenoko, Gunawan Tri, S.

Varied Corner Joint Design Aluminium 6061 using Friction Stir Welding

SekolahVokasi University of Gadjah Mada

ICOMERA-72 C S Kuo, F C Lee, C Y Huang, H C Chu

and C C Cheng

A self-balance system for naval operation vehicles Department of Mechanical and Electro-

Mechanical Engineering, University National Sun Yatsen, Taiwan

ICOMERA-04A A. Suhartomo, W Simatupang, B Widjaja, and F Gapsari

Feasibility Study on Structural Health Monitoring Systems using Fiber-Optics Sensor (FOS) Technology

for Transportation Infrastructures in Indonesia

Electrical Engineering Study Program, President University

ICOMERA-10A Renny Septiari, Pratikto, Purnomo B. Santoso, and Ishardhita P. Tama

The dominant factor that influences changes in work position on beverage packing work

Industrial Engineering, National Institute of Technology (ITN) Malang

ICOMERA-18A Galang Sandy Prayogo, Nuraini Lusi Determining the Effect of Machining Parameters on

Material Removal Rate of AISI D2 Tool in Electrochemical Machining Process using the Taguchi Method

Mechanical Engineering Department, State

Polythecnic of Banyuwangi

ICOMERA-27A Arya Mahendra Sakti, Dyah Riandadari, Hanna Zakiyya, Aditya Prapanca

The Effect of Process Variables to Thickness and Shining of Specimen of Nickel-Chrom Metal Coating Process.

Mechanical Engineering Department, Surabaya State University

26

Topic: Manufacturing (continued)

ICOMERA-28A Abdurrohman, Khairul Muzaka, Chairul Anam

Optimation of Excitation Source and DVA Mass of Center-of Gravity in Main System with 2-dof to Reduce Translational and Rotational Vibration

Mechanical Engineering Department, State Polythecnic of Banyuwangi

ICOMERA-103 Achmad As'ad Sonief, Fikrul Akbar Alamsyah, Arda Nur Fauzan

Evaluation of Surface Roughness of Aluminium Produced by end-mill slot process with variable helix angle


ICOMERA-107 Putu Hadi S., F Gapsari, Purnomo and R A Putra

Fabrication of Aluminum Using Casting Method Made For Anodizing Process On Biomaterial

Applications – A Review


ICOMERA-109 Moch. Syamsul Ma'arif, Resza Tania Putri, Khairul Anam

Effect of Bio-based Adhesive on Tensile Strength and Bending of Balsa Wood

Adhesive Joint


ICOMERA-117 Djarot B. Darmadi The mechanical properties of aluminum double side friction stir welded with varied length of pin


ICOMERA-123 Yudy Surya Irawan Anisotropic torsion strength of round bar A6061 friction weld joint with various upset pressure


ICOMERA-126 Bayu Satriya Wardhana The effect of cutting parameters on the characteristics of 316L surface with laser cutting


ICOMERA-128 Fikrul Akbar Alamsyah The Kinematics Analysis of Robotic Arm Manipulators Cylindrical Robot (RPP) Type for FFF 3D Print Using Scilab


ICOMERA-130 Hastono Wijaya The Effect of Power Supply Current on Recast Layer in

S45C Steel using Wire EDM

Mechanical Engineering Department,

Brawijaya University

ICOMERA-32A IP Tama, R Yuniarti, A Eunike, I Hamdala,

W Azlia

Risk Identification in Cassava Chip Supply Chain Using

SCOR (Supply Chain Operation Reference)

Industrial Engineering, Engineering

Faculty, University of Brawijaya

27

Topic: Design and Industrial Engineering

ICOMERA-01 Sofyan Arief Setyabudi, Moch. Agus

Choiron, Anindito Purnowidodo

Simulation of the Tensile Test of the Fiber Carbon

Composite with Finite Element Approach


Brawijaya University

ICOMERA-07 Mukhlis Muslimin, I. N. G. Wardana, Sofyan Arif Setya Budi, Kusno Kamil

Liquid Smoke Potential Solution on Texture and Bonding Sago Fiber-Matrix

Mechanical Engineering Department, Khairun University

ICOMERA-36 Jahirwan Ut Jasron, Sudjito Soeparman, Lilis Yuliati, Djarot B. Darmadi

Experimental Study on the Effect of Ocean Wave Characteristics on Air Pressure in Oscillating Water Column

Device

Mechanical Engineering Department, Nusa Cendana University

ICOMERA-40 M. Mirza Abdillah Pratama, Rizaldy Khoiru Suhud, Poppy Puspitasari, Fuad Indra Kusuma, Andika Bagus Nur Rahma Putra

Finite element analysis of the bending moment-curvature of the double-layered graded concrete beam

Civil Engineering Department, Universitas Negeri Malang

ICOMERA-43 Satryo B. Utomo, Winarto, Agung S. Widodo, ING Wardana.

Effect of Limited Migration of Graphite and Sea Water Electron as a Sensor to Control DC Voltage Regulator

(CVR)

Mechanical Engineering Department, Jember University

ICOMERA-46 Aufar Syehan, Anjas Trihatmojo Pamungkas and Danardono Agus Sumarsono

Static Simulation of e-Bike Tilting Three-Wheeled Frame Structure Using the Finite Element Method

Mechanical Engineering Department, University of Indonesia

ICOMERA-47 Shigeyuki Haruyama, Moch. Agus Choiron, and Didik Nurhadiyanto.

Design of Laminated Corrugated Metal Gasket Using Spring Effect by Finite Element Method

Management of Technology, Yamaguchi University

ICOMERA-48 Widjonarko, Rudy Soenoko, Slamet Wahyudi, Eko Siswanto

Design of Air Motor Speed Control System for Small Scale Compressed Air Energy Storage Using Fuzzy Logic

Conversion Energy, Electrical Engineering Departement, Universitas Jember

ICOMERA-49 Solechan, Rubijanto JP, Joko Triyono, Eko Pujiyanto

Study Of Making Implant Plate And Screen Of Femur Bone Internal Fictation From Hydroxyapatit Bovine And Polymer

Biodegradation Material Using 3D Printers On Mechanical Strength

Mechanical Engineering Department, Muhammadiyah Semarang University

28

Topic: Design and Industrial Engineering (continued)

ICOMERA-50 Ilham Ary Wahyudie Optimizing warm compaction parameters on the porosity and hardness of Bronze/Tin ore waste composites

Politeknik Manufaktur Negeri Bangka Belitung

ICOMERA-51 Farhan Harish Mufid and Henky Suskito

Nugroho

Comparison of Economic Cost and Effectiveness Between

Existing Salt Industry Maintenance Program, Reliability Maintenance Program and Age-Replacement Maintenance Program on Salt Crusher Machine

Department of Mechanical Engineering,

Universitas Indonesia

ICOMERA-59 Trisita Novianti, Indra Cahyadi and Dewi

Kartika Sari

Productivity Assessment of Herbicide 486 Using OREGON

PRODUCTIVITY MATRIX

Industrial Engineering, University of

Trunojoyo

ICOMERA-61 Mahrus K. Umami, Nurul I Zannah and Ida Lumintu

Evaluating the match/mismatch between the mouse dimensions and the hand anthropometry of the primary school students

University of Trunojoyo Madura

ICOMERA-65 Ika Deefi Anna, Indra Cahyadi, Ainol

Yakin

An Integrated Approach Based on ANP and Goal

Programming to Determine the Best Marketing Strategy

Industrial Engineering, University of

Trunojoyo Madura

ICOMERA-68 Sukanto, R Soenoko, W Suprapto, Y S Irawan

Parameter Optimization of Ball Milling Process for Silica Sand Tailing

Manufacturing of Bangka Belitung Polytechnic

ICOMERA-69 Shigeyuki Haruyama, Zefry Darmawan, Ken Kaminishi

Energy Absorption Characteristic of Compress-Expand Tensile Mechanism Using Finite Element Analysis.

Management of Technology, Yamaguchi University, Japan

ICOMERA-73 Masahiro Togawa, Oke Octavianty,

Shigeyuki Haruyama and Yoshie Ishii

Product Architecture Analysis of Projector and Strategy for

Gaining the Competitive Advantage

Graduate School of Science and

Technology for Innovation, Yamaguchi University

ICOMERA-01A Anis Kurniawan, Andoko Simulation of stresses and cracks on the Mitsubishi L300

pickup axle housing using the Finite Element Method


Universitas Negeri Malang

ICOMERA-02A Puteri Ardista N. Mawangi, Andoko Rocker arm failure analysis on diesel engines with finite

element method



29

Topic: Design and Industrial Engineering (continued)

ICOMERA-03A Syaiful Efendi, Andoko Design and simulation of cracks in a four-cylinder engine crankshaft using finite element method


ICOMERA-11A Aminnudin Lattice Strain in Aluminium after Plastic Deformation Process at a Cryogenic Temperatur


ICOMERA-13A Murti Astuti The role of University in Implementation of Eco-Innovation in Centre of Creative Industry of Natural Stone Craft

Industrial Engineering Department, Brawijaya University

ICOMERA-17A Nanang Ali Sutisna, Femiana Gapsari Rolling Resistance and Noise Estimation for Product Design and Development of Eco-Tyre using Finite Element and Numerical Methods

Mechanical Engineering Department, Faculty of Engineering, President University

ICOMERA-21A Ari Yuga Aswara, Andoko Failure Analysis of Material Variations in Rocker Arm with Finite Element Method


ICOMERA-22A Fikriya Mujahidin, Andoko Stress Analysis of Rear Wheel Drive of Pick-up by Finite

Element Method



ICOMERA-23A Jamili, Andoko Stress and Deformation Simulation of 6 Hole Steel Wheel

Using Finite Element Method



ICOMERA-30A Faizatur Rohmah, Fredy Kurniawan Performance of SGPN-NPs Paste Electrode as Medical Biosensor

Department of Heavy Equipment Engineering, State Polytechnic of Madura

ICOMERA-31A Dwi Hadi Sulistyarini Optimation of Composition of Premium Octane Number Blending and Sulphur of Diesel Fuel Composition in I RU IV Refinery Cilacap

Industrial Engineering, Brawijaya University

ICOMERA-105 M. Agus Choiron, Happy H. K., Anindito Purnowidodo, Ahmad Rivai

Deformation Pattern and Energy Absorption Analysis on Initial Fold Crash Box by Oblique Crash Test


ICOMERA-131 Nafisah Arina Hidayati The Initial Modelling of Hybrid Plating for Internal Fixation Construct by Using 3-D Bone Model


30

Parallel Session 1

Wednesday 24th October 2018

Majapahit Room 2a Majapahit Room 2b

Manufacturing/Material

Moderator: Agung Sugeng W, PhD.

Energy Conservation/Design/Industrial Eng.

Moderator: Dr. Sugiarto

08.00-08.15 (I) ICOMERA-01 08.00-08.15 (I) ICOMERA-18

08.15-08.30 (II) ICOMERA-02 08.15-08.30 (II) ICOMERA-104

08.30-08.45 (III) ICOMERA-03 08.30-08.45 (III) ICOMERA-102

08.45-09.00 (IV) ICOMERA-17 08.45-09.00 (IV) ICOMERA-106

09.00-09.15 (V) ICOMERA-101 09.00-09.15 (V) ICOMERA-110

09.15-09.30 (VI) ICOMERA-103 09.15-09.30 (VI) ICOMERA-113

09.30-09.45 (VII) ICOMERA-107 09.30-09.45 (VII) ICOMERA-114

09.45-10.00 (VIII) ICOMERA-108 09.45-10.00 (VIII) Reserved


Materials

Moderator: Nafisa Arina Hidyati, M.Eng.

Energy Consevation

Moderator: Dr. Eng. Nurkholis Hamidi

08.00-08.15 (I) ICOMERA-INV-02 08.00-08.15 (I) ICOMERA-INV-01







09.45-10.00 (VIII) ICOMERA-26A 09.45-10.00 (VIII) ICOMERA-24A

Lontar Room 1 Lontar Room 2

Manufacturing Moderator: Dr. Putu Hadi Setyorini

Design and Industrial Engineering Moderator: Redi Bintarto, M.Eng. Pract.

08.00-08.15 (I) ICOMERA-INV-03 08.00-08.15 (I) ICOMERA-30




09.00-09.15 (V) ICOMERA-73 09.00-09.15 (V) ICOMERA-17A

09.15-09.30 (VI) ICOMERA-19 09.15-09.30 (VI) ICOMERA-11A


09.45-10.00 (VIII) ICOMERA-09 09.45-10.00 (VIII) ICOMERA-51

31

Parallel Session 2



Manufacturing/Material Moderator: Bayu Satriya Wardhana, M.Eng

Energy Conservation/Design/Industrial Eng. Moderator: Purnami, MT.

10.15-10.30 (I) ICOMERA-109 10.15-10.30 (I) ICOMERA-13A

10.30-10.45 (II) ICOMERA 115 10.30-10.45 (II) ICOMERA-31A








Materials Moderator: Dr. Eng. Yudy Surya Irawan

Energy Consevation Moderator: Dr. Eng. Lilis Yuliati


10.30-10.45 (II) ICOMERA-19A 10.30-10.45 (II) ICOMERA-08A

10.45-11.00 (III) ICOMERA-05A 10.45-11.00 (III) ICOMERA-16A

11.00-11.15 (IV) ICOMERA-14A 11.00-11.15 (IV) ICOMERA-24

11.15-11.30 (V) ICOMERA-30A 11.15-11.30 (V) ICOMERA-09A



12.00-12.15 (VIII) Reserved 12.00-12.15 (VIII) ICOMERA-75


Manufacturing Moderator: Dr. Femiana Gapsari

Design and Industrial Engineering Moderator: Dr. Slamet Wahyudi

10.15-10.30 (I) ICOMERA-04A 10.15-10.30 (I) ICOMERA-59

10.30-10.45 (II) ICOMERA-18A 10.30-10.45 (II) ICOMERA-61





11.45-12.00 (VII) ICOMERA-27A 11.45-12.00 (VII) ICOMERA-43


32

Parallel Session 3


Parallel Session 3


Materials Moderator: Fikrul Akbar Alamsyah, MT.

Energy Conservation Moderator: Dr. Eng. Widya Wijayanti

15.00-15.15 (I) ICOMERA-15A 15.00-15.15 (I) ICOMERA-52

15.15-15.30 (II) ICOMERA-20A 15.15-15.30 (II) ICOMERA-23

15.30-15.45 (III) ICOMERA-25A 15.30-15.45 (III) ICOMERA-62



16.15-16.30 (VI) ICOMERA-12A 16.15-16.30 (VI) ICOMERA-115

16.30-16.45 (VII) ICOMERA-07A 16.30-16.45 (VII) Reserved

16.45-17.00 (VIII) ICOMERA-04 16.45-17.00 (VIII) Reserved


Manufacturing Moderator: Rudianto Raharjo, MT.

Design and Industrial Engineering Moderator: Khairul Anam, ST., M.Eng.



15.30-15.45 (III) ICOMERA-71 15.30-15.45 (III) ICOMERA-01A

15.45-16.00 (IV) ICOMERA-10A 15.45-16.00 (IV) ICOMERA-02A


16.15-16.30 (VI) ICOMERA-28A 16.15-16.30 (VI) ICOMERA-22A

16.30-16.45 (VII) ICOMERA-32A 16.30-16.45 (VII) ICOMERA-21A

16.45-17.00 (VIII) ICOMERA-105 16.45-17.00 (VIII) ICOMERA-23A

participant guide book -...

Documents