part description page part description -...

221 W. Santa Fe Ave,. Fullerton, CA 92832(714-870-9881) C FAX (714-870-6399) C E-MAIL: [email protected]

Page Part Description2 HydroDrill Layout3 HydroDrill Replacement Parts4,5 HydroDrill User Instructions6 HydroDrill Augers7 Right Angle Wrench8 Right Angle Wrench Descriptions9 Right Angle Wrench

Essentials Only10 Right Angle Wrench Replacement

Parts11 Combined Right Angle Wrench &

Clean Out Plug Wrench Set12 Adjustable Jack Stand13 Clean Out Plug Wrench Sets14 Clean Out Plug Wrench

Replacement Parts15 Clean Out Plug Wrench Set

with Reversing Ratchet Wrench16 Clean Out Plug Wrench Ratchet

Set Replacement Parts17 Clean Out Plug Wrench Sets - No

Carrying Case18 3/4" Drive Ratchet Wrench19 Valve Operator Key Set20 Spud Nut Wrench21 Hydrostatic Test Pumps, 600psi22 Hydrostatic Test Pumps, 300psi23 600 psi Hydrostatic Test Pump

Replacement Parts24 300 psi Hydrostatic Test Pump

Replacement Parts25 Water Meter/City Meter Keys26 Double Slotted Water Meter Key

Page Part Description27 ABS Adaptor (NST to IPS)28 Sloan Tailpiece Tool29 Faucet Nut Saw30 Emergency Gas Shut-Off Wrench31 Tailpiece Flanging Tool32 Tailpiece Flanging Tool

Instructions33 Stuvel Flush Valve Reseater34 Tile Probes35 Band-Aid Pipe Clamp36 Miscellaneous Tools37 Floor Drain Wrench38 Sinklear Garbage Disposal

Installer Tool39 In-Sink Installer Tool for Garbage

Disposal Flange40 Erickson Drain Cleaner Snakes

221 W. Santa Fe Avenue, Fullerton, CA 92832(714-870-9881) ∙ FAX (714-870-6399) ∙ E-MAIL: [email protected]

PERFECTO HYDRODRILL LAYOUT

HOW THE HYDRODRILL WORKS:The Chuck Adaptor is inserted into the chuck of your drill. The Chuck Adaptor, the Shaft and the MalePipe Fitting are all solidly attached together, and rotate with the drill. The Shaft Bearings allow the Shaft toturn freely. A hose is attached to the Hose Fitting. When the water is turned on and the valve is opened,water runs through the valve and into the Hydrodrill body. The Shaft Seals keep the water from leaking out.There is a hole in the side of the Shaft, and another hole that runs down the length of the Shaft out the end.The water enters the side hole and runs out the end. From there it fills the pipe attached to the Male PipeFitting, and from there out through the Hydrodrill Auger.


REPLACEMENT PARTS FOR THE #1HYDRODRILL (PART No. 1502)


#1 HYDRO-DRILL: 5/8" Shaft

The power for drilling is supplied by a 1/2" drill –

preferably a 450 RPM drill. Water is supplied to break

up the ground and help keep the bit cool while drilling.

YOU CAN BORE UP TO 200 FEET FOR 1/2" to 8" PIPE!

The HYDRO-DRILL is a rugged tool,

designed with the best materials available.

The chuck-end is manufactured from an

alloy steel to prevent breakage due to

impact shock. The threaded male end is

forged steel for wear strength, and the blade

is welded steel with a hard facing on the

cutting edges of the blades, to give them a

longer drill life.

This very versatile earth boring tool is used to

eliminate excavating when putting in utility services

under existing driveways, sidewalks or landscapes.

The standard HYDRO-DRILL kit comes with a 2"

bit. Additional standard bits are available in 1"

through 12" sizes. Carbide tipped auger bits are

available in 1-1/4", 1-1/2" and 2" sizes.

HYDRO-DRILL

BEFORE USING, READ CAREFULLY

INSTRUCTIONS FOR OPERATING THE HYDRO-DRILL

IN BORING A HOLE, CAREFULLY ALIGN PIPE WITH THE OPPOSITE SIDE. IF YOU STAY ON TARGET

FOR THE FIRST TEN FEET, THE TOOL WILL RUN STRAIGHT FOR THE REMAINDER OF THE BORE. SET

THE DESIRED GRADE WITH A LEVEL.

PLEASE OIL FREQUENTLY WITH A GOOD LUBRICATING OIL ON BOTH THE INSIDE AND OUTSIDE, ON

THE SHAFT.

DIFFERENT SOILS WILL REQUIRE DIFFERENT AMOUNTS OF BOTH WATER AND PRESSURE ON THE

TOOL. FOR EXAMPLE, IN GUMMY, STIFF DIRT OR CLAY, A 3" BIT WILL DRILL FASTER THAN A 2" BIT.

WHEN BORING THROUGH ROCKY SOIL, BORE WITH CAUTION. IF YOU HIT A ROCK, THE BIT WILL

VEER OFF TRACK. IF THIS HAPPENS, THE DRILL SHOULD BE SHUT OFF AND THE WATER LEFT

RUNNING. WITH SEVERAL FORWARD AND BACKWARD MOTIONS YOU CAN USUALLY PUSH THE

ROCK ASIDE SO THAT THE BIT WILL PASS WITHOUT LOSING IT’S ALIGNMENT. IF THIS DOES NOT

WORK, TURN THE DRILL ON AND MOVE VERY SLOWLY UNTIL THE BIT HAS MADE A GROOVE IN THE

ROCK. THEN IT WILL NOT SLIP OUT OF ALIGNMENT AND YOU MAY EXERT MORE PRESSURE. (WE

DO NOT GUARANTEE OUR BITS AS ROCK BITS, BUT USERS ARE GENERALLY GETTING GOOD

RESULTS.)

HELPFUL HINTS TO ENSURE PROPER BORING:

• NEVER PUT SIDE PRESSURE ON THE DRILL. THE PRESSURE MUST BE EXERTED IN A

STRAIGHT FORWARD MOTION. SIDE PRESSURE OR PUTTING “ENGLISH” ON THE DRILL WILL

WEAR OUT THE BEARINGS PREMATURELY.

• YOU MUST AT ALL TIMES RUN THE TOOL WITH WATER, AND USE A STRAIGHT PIECE OF

PIPE.

• IT IS A GOOD IDEA TO USE A DRILL WITH A CHUCK NO LARGER THAN 3/4". WE RECOMMEND

A 1/2" DRILL FOR THE #1 HYDRO-DRILL. THREADS ON COUPLINGS SHOULD BE CHECKED

FREQUENTLY. IF THEY ARE WORN, THEY SHOULD BE REPLACED.

• TO GET BEST RESULTS, USE A 450 RPM DRILL. DO NOT USE A DRILL OVER 700 RPM. DO NOT

USE AN AIR IMPACT TOOL OR AN ELECTRIC IMPACT TOOL.

• TAKE YOUR TIME – IT IS MUCH BETTER TO BORE SLOWLY AND CAREFULLY THAN

HURRIEDLY.

IN BORING WITH A 4" OR LARGER BIT, MAKE A 2" BORE AS ABOVE. THEN REMOVE THE 2" BIT AND

REPLACE IT WITH A 4" OR LARGER REVERSE BIT. THEN SIMPLY BACK OUT OF THE HOLE YOU JUST

DUG. DO NOT REVERSE THE DIRECTION OF THE DRILL!! THE REVERSE BITS ARE DESIGNED TO

WORK WITH THE DRILL MOTOR RUNNING IN THE FORWARD DIRECTION. RUNNING THE DRILL

MOTOR IN REVERSE WILL UNSCREW THE PIPE THREADS AND LEAVE YOUR EXPENSIVE BIT

SOMEWHERE IN THE MIDDLE OF THE HOLE.

BE SURE TO MAINTAIN A CONSTANT DRILL SPEED WHEN THE REVERSE BORE IS BEING MADE. THIS

ASSURES YOU OF A CLEAN BORE, AND SAVES UNDUE STRAIN ON YOUR DRILL. THE PIPE SHOULD

THEN BE IMMEDIATELY INSTALLED INTO THE BORE.

CAUTION! This unit should NOT be used without proper grounding. Attach the included ground wire to the water

inlet valve, and to any solid ground, preferably a steel rod driven into the ground. More wire may be needed than the

length provided.


AUGERS FOR THE HYDRODRILL

1" FORWARD PART 1504-1 4" REVERSE PART 1504-4R2" FORWARD PART 1504-2 6" REVERSE PART 1504-6R3" FORWARD PART 1504-3 8" REVERSE PART 1504-8R4" FORWARD PART 1504-4F2" CARBIDE AUGER PART 1504-200C


This is the best tool for the worst jobs! Justbecause the plumbing is in a tight space doesn’tmean you have to crawl into it. Let Perfecto’sRight Angle Wrench do the crawling for you!

Set the wrench head on the pipe or thestubborn nut and make sure the grip is tight. Then insert the extension piece into the socket onthe wrench head. With the T-handle on the otherend of the extension, you’re ready to twist awaywithout having to worry about bruised knucklesor scraped skin.

You can even plug the T-handle straight intothe wrench head for other situations.

Need to tighten down on the slip nut? Justput the wrench head in your hand and snug up theconnection without any handle getting in yourway.

PERFECTO RIGHT ANGLE WRENCHAlso available with a complete

Deluxe Set (Shown): Part No. 1700D set of Clean Out Plug WrenchesSuper Deluxe Set: Part No. 1700SD In a single box (Part No. 1700-DWP)


RIGHT ANGLE WRENCH SETSDifferences between DELUXE and SUPER DELUXE sets

DELUXE For the deluxe sets, the handle is a forged sliding T-bar. It has a 3/4" male endthat fits into a 3/4" female socket on the DELUXE extension. The overall lengthof the extension is 28".

SUPER DELUXE The handle for the SUPER DELUXE is identical to the DELUXE. The differenceis that the extension consists of two (count ‘em, two) extensions, each 17" long, sothe overall length of the extension is 34".


PERFECTO RIGHT ANGLE WRENCHDELUXE – ESSENTIALS ONLY

PART No 1700-DE

This kit includesonly the parts seenhere: The SlidingT-Bar, the 28”Extension. And theWrench Head


REPLACEMENT PARTS FOR THE RIGHT ANGLE WRENCHES

221 W. Santa Fe Ave,. Fullerton, CA 92832(714-870-9881) C FAX (714-870-6399)website: www.perfectoproducts.net C E-MAIL: [email protected]

PERFECTO COMBINED WRENCH SETDeluxe Right Angle Wrench Set with a complete set of Clean Out PlugWrenches: Part No. 1700-DWP

This set combines two of our most popular tool kits: The Deluxe Right Angle Wrench, and the

11 piece Clean Out Plug Wrench Set. All the pieces fit into a single box, so you save valuable

floor space in your truck. The 19" sliding T-Bar can be used with or without the 28" extension.

Don’t crawl in to a cramped space to get at the problem, let our tool do that for you. Access

plus leverage, and now add a clean out plug wrench for most popular sizes and styles. The

perfect combination.

221 W . Santa Fe Ave,. Fullerton, CA 92832

(714-870-9881) C FAX (714-870-6399) C E-MAIL: [email protected]

ADJUSTABLE JACK STAND

Part number: 7000-JSD

Use this handy jack stand to hold and balanceItems while you make adjustments.

! Sturdy welded construction! Easy adjustment with ACME threaded rod

! Yoke type saddle

CAN BE USED WITH THERIGHT ANGLE WRENCH!


CLEAN-OUT PLUG WRENCHESFITS RAISED HEAD, COUNTERSUNK OR SLOTTED CLEAN OUT PLUGS

PART No 1701-CPX: COMPLETE SET (10 PIECES w/ BOX and HANDLEPART No 1701-CPW: COMPLETE SET (10 PIECES w/ BOX NO HANDLE

Wrench Description Part Number Wrench Description Part NumberRaised Head: 7/8” ID 1701-RHW #1 Countersunk: 7/8” Square 1701-CSW #7Raised Head: 1-1/16” ID 1701-RHW #2 Countersunk: 1-1/8” Square 1701-CSW #8Raised Head: 1-1/4” ID 1701-RHW #3 Countersunk: 1-1/4” Square USE 1701-RHW #1Raised Head: 1-3/4” ID 1701-RHW #4 Slotted: 1/4” x 1” 1701-SSW #10Raised Head: 2-1/8” ID 1701-RHW #5 Slotted: 1/4” x 1-3/4” 1701-SSW #11Countersunk: 3/4” Square 1701-CSW #6 Slotted: 1/4” x 2-1/2” 1701-SSW #12 (Special Order)


REPLACEMENT PARTS FOR CLEAN OUTPLUG WRENCH SETS

Wrench Description Part Number Wrench Description Part NumberRaised Head: 7/8” ID 1701-RHW #1 Countersunk: 7/8” Square 1701-CSW #7Raised Head: 1-1/16” ID 1701-RHW #2 Countersunk: 1-1/8” Square 1701-CSW #8Raised Head: 1-1/4” ID 1701-RHW #3 Countersunk: 1-1/4” Square USE 1701-RHW #1Raised Head: 1-3/4” ID 1701-RHW #4 Slotted: 1/4” x 1” 1701-SSW #10Raised Head: 2-1/8” ID 1701-RHW #5 Slotted: 1/4” x 1-3/4” 1701-SSW #11Countersunk: 3/4” Square 1701-CSW #6 Slotted: 1/4” x 2-1/2” 1701-SSW #12 (Special Order)

221 W. Santa Fe Avenue, Fullerton, CA 92832 (714-870-9881) ∙ FAX (714-870-6399) ∙ E-MAIL: [email protected]

THE CLEAN OUT PLUG WRENCH SET

WITH REVERSING RATCHET WRENCH

Part No 1701-CPR

1701-RHW #1 Raised Head: 7/8” ID 1701-CSW #6 Countersunk: 3/4” SQ

1701-RHW #2 Raised Head: 1-1/16” ID 1701-CSW #7 Countersunk: 7/8” SQ

1701-RHW #3 Raised Head: 1-1/4” ID 1701-CSW #8 Countersunk: 1-1/8” SQ

1701-RHW #4 Raised Head: 1-3/4” ID 1701-RHW #1 Countersunk: 1-1/4” SQ

1701-RHW #5 Raised Head: 2-1/8” ID 1701-SSW #10 Slotted” 1/4”x 1”

1701-SSW #11 Slotted: 1/4” x 1-3/4”

(Plugs Not Included)

221 W. Santa Fe Avenue, Fullerton, CA 92832 (714-870-9881) ∙ FAX (714-870-6399) ∙ E-MAIL: [email protected]

REPLACEMENT PARTS FOR

THE CLEAN OUT PLUG WRENCH SET

WITH REVERSING RATCHET WRENCH

1701-RHW #1 Raised Head: 7/8” ID 1701-CSW #6 Countersunk: 3/4” SQ

1701-RHW #2 Raised Head: 1-1/16” ID 1701-CSW #7 Countersunk: 7/8” SQ

1701-RHW #3 Raised Head: 1-1/4” ID 1701-CSW #8 Countersunk: 1-1/8” SQ

1701-RHW #4 Raised Head: 1-3/4” ID 1701-RHW #1 Countersunk: 1-1/4” SQ

1701-RHW #5 Raised Head: 2-1/8” ID 1701-SSW #10 Slotted” 1/4”x 1”

1701-BX 19-3/4” x 6” x 4” BOX 1701-SSW #11 Slotted: 1/4” x 1-3/4”

1701-RAT12 Reversing Ratchet Wrench 7000-3450 3/4"x 1/2" Adapter


CLEAN OUT PLUG WRENCH SETS

ALSO AVAILABLE WITHOUT ACARRYING CASE


(714-870-9881) C FAX (714-870-6399) C E-MAIL: sales@ perfectoproducts.net

VALVE OPERATOR KEY SET Part No. 1600-VO

OPEN AND CLOSE YOUR UTILITY VALVESWITH THIS MULTI-FUNCTION KIT

This set includes valve operator keys for manysized valves:

2" Square Head 1-3/4" Square Head1-1/2" Square Head 1-1/4" Square Head1" Square Head

All sizes smaller than 2" nest inside the 2" operatorand bolt in for extra strength. Plus a 7/8" slottedkey and a 2-prong head for small valve handles

Two 28" extensions and a sliding T-Handle makefor easy operation. All come packaged in a 29" x 6" x 3" metal box.


SPUD NUT WRENCHES

INSTALL AND REMOVE CLOSET AND URINAL SPUDS WITH THESEHANDY, DURABLE WRENCHES. SLOTS IN THE TOOL LINE UP ANDGRIP FIRMLY TO THE RAISED RIDGES. THE FULL TOOLKIT (7000-SNW) HAS A 3/4" x 1/2" SOCKET ADAPTOR FOR YOUR 1/2"RATCHET WRENCH.

PART NUMBERS:

3/4" 7000-SNW-34 1-1/4" 7000-SNW-1141-1/2" 7000-SNW-112 2" 7000-SNW-2

ALL 4 WRENCHES IN A CARRYING CASE 7000-SNW


HYDROSTATIC TEST PUMPS

Deluxe upgrade (D6) comes with a shut offvalve, a 600 # pressure gauge, and a bleed valve



300V: High Volume, Rated to 300 psig.

300D6 includes Deluxe Upgrade

The body is made from 356 cast Aluminum, the shaft is 416 Stainless Steel,The valves are Bronze ball-type check valves with female threads.

HYDROSTATIC TEST PUMPS


REPLACEMENT PARTS FOR THE 1000 SERIES PUMPS

A 3/4” HOSE SWIVEL 1000-HS B 1/2” BRASS CHECK VALVE 1000-CV

C 3/4” x 1/2” BUSHING 1000-B D 7/8” O-RING 1000-OR

E 7/8” PACKING NUT 1000-PN F 7/8” SS PISTON 1000-P

G PUMP HANDLE 1000-H H 1/2” BRASS BALL VALVE 1000-BV

I 2” 600 # PRESSURE GAUGE 1000-G J 1/2”x1/2”x1/4” TEE w/ VALVE 1000-TR

ITEMS H, I and J COME WITH THE 1000D6 PUMP

221 W. Santa Fe Ave,. Fullerton, CA 92832(714-870-9881) ∙ FAX (714-870-6399) ∙ E-MAIL: [email protected]

REPLACEMENT PARTS FOR THE300V AND 300D6

1. 300-CV 3/4” BRONZE CHECK VALVE2. 300-P 1-1/4” STAINLESS PISTON3. 300-H CAST ALUMINUM HANDLE4. 300-PG 1-1/4” PACKING GLAND5. 300-V 3/4” BRONZE BALL VALVE6. 1000G 0-600# PRESSURE GAUGE7. 1000-TR 3/4”x3/4”x1/4” TEE w/ BLEED VALVE8. 1000-BV 1/8” BRASS BLEED VALVE


WATER METER and CITY METER KEYS

DOUBLE-SLOTTEDWATER METER KEY

Two meter keys for the price of one!

Part No. 1602-MKH



Make a quick connection from anexisting iron body clean out to ABSpipe without bushings or maleadaptors! Just remove the threadedplug, and screw in the NST to ABSadaptor. Then just couple up thepipe. Simple, inexpensive,efficient.

NST to IPS ADAPTORFor Connecting ABS Pipe To An Existing Clean Out

3-1/2" NST to 3" IPS Part No. 7000-ABS 2-1/2" NST to 2" IPS Part No. 7000-ABS2



SLOAN TAILPIECE TOOLSTURDY WELDED STEEL CONSTRUCTION

SLOTTED END FITS INTO THE SLOAN TAILPIECE, CATCHES THE RAISED RIDGES, AND ALLOWS

YOU TO UNSCREW THE TAILPIECE WITHOUT DAMAGING THE CHROME FINISH

3/4" SQUARE HOLE ADAPTS TO THE PERFECTO RIGHT ANGLE

WRENCH.

- - - - - OR - - - - -

PUT A CRESCENT WRENCH ON THE SQUARE END.


FAUCET NUT SAWPart No. 7000-NS

GRIND THROUGH FAUCET NUTS IN SECONDS WITHTHIS CARBIDE SAW IN YOUR DRILL.

SAFETY FIRST:WEAR GLASSES


EMERGENCY GAS SHUT-OFF WRENCH

Part Number 7000-EW

In an emergency, such as an earthquake,don’t fumble in the dark when you suspect that there’s a gas leak in the house.Leave this sturdy tool right next to thegas meter so its there when you need it.

Sturdy steel construction

1/2" slotted to fit household gas meters



A-964 SPEED TYPE TAILPIECEFLANGING TOOL

MAKES 1-1/4" or 1-1/2" TAILPIECES FROM YOUR SCRAPTUBING (One tool for each size)

Capacity: 1-1/2" OD Tubing 17 to 20 gauge

NO POUNDING OR HAMMERING



A-964 FLANGING TOOL

OPERATING INSTRUCTIONS:

1. Turn the black handle on the flanging tool until the ball in the head of the flanging tool is allthe way into the head.

2. Put the brass tubing to be flanged over the knurled end of the tool until it is right against thelip of the tool where the ball shows

3. Put the brass tubing (with the tool inside) into a pipe vise. Tighten the vise down so that itholds both the brass tube and the knurled part of the handle.

4. Turn the handle clockwise once around so that the ball begins to flare the tubing.5. Twist the handle slightly, so that the ball moves out from the head.6. Repeat steps 4 and 5 until the ball has moved all the way out, and the brass tubing has a good

flange on it.


STUVEL FLUSH VALVE RESEATER TOOL■ CUTS WATER BILLS ■ STOPS COSTLY FLUSH VALVE LEAKS

Every plumber should have this handy tool, invented by a plumber. Use theStuvel Reseater Tool and move on to more profitable jobs. A few turns of thewrist reseats the roughest valve seat in perfect alignment with the pull-wireguide. Lime and corrosion – which are the cause of the leaks – are removed in asnap!

1) Remove flush ball and wire.2) Insert sliding pin in the guide.3) Exerting downward pressure, twist tool back

and forth until the valve seat is smooth.4) The grinding ball does the work. It resurfaces

any size flush valve seat.

221 W. Santa Fe Ave,. Fullerton, CA 92832 ! (714-870-9881) C FAX (714-870-6399)website: www.perfectoproducts.net C E-MAIL: [email protected]

PERFECTO TILE PROBES

Part No: 1800-4T, 1800-5T, 1800-6T(Always use safety gloves to prevent electrocution)


BAND-AID PIPE CLAMPPart No. 7000-BAPC

For those quick-fixes until the repair can be made. The water pressure can stay on 3” clamp fits up to 2” pipe Heavy duty worm gear for a secure clamp 1” Square rubber seat covers most leaks Re-Usable


OUTSIDE EASY OUTPart No. 7000-EO

Tighten the bolts down and turn with a water meter key

PERFECTO WASHERTRIMMERPart No. 7000-WT

FLOOR DRAIN WRENCHPart No. 7000-DW



This simple tool is a mustwhen the floor draincompression ring isjammed tight! Forgetscrewdrivers, chisels, orpry bars. Forget wastingtime trying to figure outwhat tool to use.

This sturdy tool is madefrom 3/8" steel plate, flamecut to fit exactly into thegrooves in the inner ring.

Just drop the drain wrenchinto place and insert a 3/8"square ratchet wrench(you’ll probably need anextension) and twist thatdrain ring out in seconds.

Don’t waste your time onsimple tasks, when there’sa simple tool to deal withit.



THE SINKLEAR TOOLfrom PLUMB E-Z, Inc.

Use this simple, unique tool to install a garbage disposal single-handed,and in less time. Simply lower the tool through the sink flange (alreadyinstalled) into the mouth of the disposal, then hoist the disposal intoplace. Slip the slotted plate onto the threaded shaft on the sink side,and the disposal will stay in place. Reach under the sink, turn the lockring, and you’re done. Comes in it’s own carrying case.



THE IN-SINK INSTALLERfrom Plumb-E-Z, Inc.

(Perfecto Part No. 6000-IN)

Install the flange for a garbage disposal with ease! Just putty upthe flange, assemble the parts on the IN-SINK INSTALLER, snug upthe top clamp on the threaded rod and then snap the ring off thecup with a screwdriver. That’s it! (Full installation instructionsincluded.)



IMPORTANT FEATURES:

• A TW O OR THREE HOUR JOB CAN BE DONE IN 15 OR

20 MINUTES.

• NO DISCONNECTING OF PLUMBING NECESSARY.

• W ILL NOT CROSS TEES OR GO UP VENT

• EXCLUSIVE PATENTED CRAWL HEAD

• EASY TO TIGHTEN SET SCREW

• POSITIVE LOCK CABLE

• A PERFECTLY BALANCED CONTAINER

DRAIN CLEANERSNO MORE REMOVING TRAPS TO CLEAN DRAINS!

Your supplier for all Quality Erickson Products is:

part description page part description -...

Documents