paper-ii ( sets)
TRANSCRIPT
-
7/30/2019 Paper-II ( Sets)
1/21
Set -1
1. Mark the correct statement.a) Elastic stop nut can be used many
time.b) As in a) & when turn with fingers,
replace it.c) Every time the parts disassembled,
replace the elastic stop nut.
d) As in c) & used at place wheretemperature exceed 250F.2. Which type of Synthetic rubber will bethe first choice for manufacturing ofaircraft tubeless tyre
a. Butyl rubber b. Neoprene rubberc. BUNA-N d. thiokol
3. Which synthetic rubber is chiefly used inaircraft hot air duct as sealing ring andwire insulation
a. Silicon rubber b.Polymethane rubber c. BUNA-S d.BUNA-N
4. Highest resistance to deterioration butlowest physical property is thecharacteristic of which kind of syntheticrubber.
a. GR I b. GR Sc. GR P d.
GR A
5. To valcanise thiokol rubber, whichelement to be added
a. Sulfur b. Sulfuroxide c. Zinc d. Zinc oxide
6. Which material is used formanufacturing of hydraulic booster pistonseal
a. Styrene butadiene seal b.Nitrile rubber
c. Flexon rubberd. Fluoro carbon rubber
7. Natural rubber attains fibrous structurewhen
a. It under goes at lowtemperature b. It is frozen
c. It is heated to 1300C d.It undergoes continues stress at normal
temperature
8. The grade of Kevlar fiber is used foraircraft structure
a. Kevlar 49 b. Kevlar 149 c.Kevlar 29 d. Kevlar 129
9. The composition for E glass is
a. Magnesia-alumina-silicate glassb. Lime-alumina
borosilicate glassc. Soda borosilicate glass
d. None of the above
10. Truly outstanding properties ofstrength competes with stronger steel iskind of fiber
a. S glass b. Hollowfibre glass c. A glassd. Carbon glass
11. Which composit material is difficult tocut or drill
a. Glass fibre b. Aramidc. Carbon / Graphite
d. None of above
12. Mark the wrong statement for carbon /graphite fibre
a. Is used to fabricate primary
structure b. It has high strength andhigh rigidityc. It takes compressive load
d. It is ductile in nature
13. Corrosion control techniques areemployed when corbon fibre is in contactto aluminium
a. A layer of fiber glass is used asa barrie
b. Aluminium is anodized, primedand painted prior to assembly
c. Both (a) and (b) will be appliedtogether
d. None of the above
14. Which composite material is useful formaking aircraft parts that are subject tohigh stress and vibration
a. Fibergalss b. Aramid c.Carbon / Graphite d. None of these
15. Mark the correct statementa. Carbon fiber are electrically
non conductiveb. Carbon fibers have high
thermal expansionc. Carbon fibers have high fatigue
resistance
16. Boron fibers are made by sintering theboron elements on a thin film of material
a. Titanium b. Tinc. Tungsten d. All above
17. Which fiber material bears all tension,compression and bending stresses
a. Ceramic fiber b. Boronfiber c. Fiber glass d. Graphite fiber
-
7/30/2019 Paper-II ( Sets)
2/21
18. Mark the correct statement in FiberOrientation
a. Warp direction is designated at900
b. Weft is designated at 00
c. Bias is at 450 angle of fillthreads
d. None of the above
19. For repairing of fabric, which weave tobe useda. Plain weave b. Basket weavec. Satin weave d. All of these
20. Find out the wrong answer: Hybrids ofcomposite material used in Aviation fieldare
a. Kevlar with carbon / graphiteb. Kevlar with fiber glass
c. Carbon / graphite with fiberglass d. None of these
21. In fiber science, which acts as a curing
agent a. Resin b. Matrixc. Catalyst d.
All of these
22. Plexiglass isa. Thermoplastic b.
Thermoset c. Laminatedd. None of these
23. Mark the correct answer:Apart from strongest adhesive
characteristics of epoxy resin, it has otheradvantages
a. Useful at very high temperatureb. It withstand bendingstress
c. Reasonable rigidity and flexibilityd. All of these
24. Mark the correct answer:The advantages of fillers to add to
resins area. To control viscosity and weight
b. To increase pot life andstrength
c. Both (a) and (b)d. None of these
25. Nomex is aa. Filler material b. Matrix
c. Reinforced fiber d.Core material
26. Tapered roller bearing supporta. Radial load b. Thrust load c.
Both (a) and (b)
27. Bearing used on high powered aircraftengine is
a. Ball bearing b. Rollerbearing c. Plain bearing d. Both (a) and (c)
28. Plain bearings are used fora. Connecting rods b. Crank
shaft c. Cam shaft d.All of these
29. Bearings are used to takea. Thrust load b. Radial
load c. Side load d.Both (a) and (b)
30. Bearing used where high compressivepressure, is generally made ofa. Babitt b. Bronze
c. Siliver bronze d. All of these
31. Bearing which offer more friction ismade of
a. Bronze b. Babittc. Silicon d.None of these
32. The amount of electricity a capacitorcan store is directly proportional to
a. Distance between the plate andinversely proportional to theplate area
b. Plate area and is not affectedby the distance between theplate.
c. Plate area and inverselyproportional to the distance
between the plated. None of these
33. The correct way to connect a test voltmeter in a circuit is
a. In series with a unit b.Between the source voltage and the load
c. In parallel with unit d.Both (a) and (c) are correct
34. Typical application of Zener diode is asa. Full wave rectifiers b.
Half wave rectifierc. Voltage regulator d.
Amplifier
35. The method used to rapidly charge aNickel Cadmium battery utilizes
a. Constant current and constantvoltage b. constant current and varyingvoltage
c. Constant voltage and varyingcurrent
d. Varying voltage and varyingcurrent
-
7/30/2019 Paper-II ( Sets)
3/21
36. What tasks are completed prior toweighing an aircraft to determine its emptyweight
a. Remove all items except thoseon aircraft equipment list, drainfuel and hydraulic fluids
b. Remove all items on theaircraft equipment list, drainfuel, compute oil and hydraulic
fluid weightc. Remove all items except thoseon the aircraft equipment list,drain fuel and fill hydraulicreservoir
d. All of these
37. Useful load of an aircraft is thea. Difference between the
maximum gross weight andempty weight
b. Difference between the netweight and total weight
c. Some of the empty weight and
the max. gross weightd. Weight of the fuel
38. Certain amount of slacks must be leftin flexible hose during installation becausewhen under pressure it
a. Expand in length and diameterb. Expand in length and contracts
in diameterc. Contracts in length and
expands in diameterd. Contracts in length and
diameter39. Excessive stress on fluid or pneumatic
metal tubing caused by expansion orcontraction due to temperature change canbest be avoided by
a. Using short, straight sectionsof tubing between fixed partsof aircraft
b. Not projecting the aircraft tosudden change in temperature
c. Providing bends in the tubingd. None of the above
40. Which heat treating process of metalproduces a hard, wear resistance surfaceover strong, tough core
a. Case hardening b.Annealing c. Temperingd. Hardening
41. Which of the following hose materialsare compatible with phosphate-ester basehydraulic fluids
a. Butyl b. Buna-Nc. Neoprene d. Buna-S
42. In a metal tubing installation
a. Rigid straight line runs arepreferable
b. Tension is undesirable becausepressurisation will cause is toexpand and shift
c. A tube may be pulled in if thenut will start on the threadedcoupling
d. None of the above
43. Magnetic particles inspection is usedprimarily to detect
a. Distortionb. Deep surface flaw
c. Flaws on or near the surfaced. Flaws in plastic material
44. Which material cannot be heat treatedrepeatedly without harmful effects
a. Unclad aluminium alloys insheet forms
b. 6061- T9 Stainless steelc. Clad aluminium alloy
d. Carbon steel45. What is generally used in theconstruction of aircraft engine fire walls
a. Stainless steelb. Chromium
Molybdenum alloy steelc. Magnesium Titanium alloy steel
d. Wrought iron46. A fiber type self locking nut must neverbe used on an aircraft if the bolt is
a. Under shear loadingb. Under tension loadingc. Subject to rotation
d. All of these
47. Aircraft bolts are usually manufacturedwith aa. Class-I fit for the threadb. Class-II fit for the threadc. Class-III fit for the threadd. Class-IV fit for the thread
48. Hose and a few projecting globules arefound in a weld. What action should betaken
a. Re-weld the defective portions
b. Remove all the old weld and re-weld the jointc. Grind the rough surface smooth,
inspect and re-weld all gaps / holesd. Can be used in the same way49. Which condition indicate a part hascooled too quickly after being welded
a. Cracking adjacent to the weldb. Discoloration of the base metalc. Gas pockets and porosityd. Slag inclusion
50. Which tool is used to measure theclearance between the surface plates and a
-
7/30/2019 Paper-II ( Sets)
4/21
relatively narrow surface being checked forflatness.
a. Depth gauge b. Thickness gaugec. Dial indicatord. Vernier
Caliper
51. Which tool is used to find the center ofa shaft or other cylinder work
a. Combination set b. Dial
indicator c. Micrometer caliperd. Set square
52. What tool is generally used to calibratea micrometer or check its accuracy
a. Gauge block b. Dial indicatorc.Machinist scale d. None of these
53. When approaching the front of anidling jet engine the hazard area extendsforward of the engine approximately
a. 10 feet b. 15 feetc. 25 feet d.
35 feet
54. Which of the following is the mostsatisfactory extinguishing agent for use ona carburetor or intake fire
a. Dry chemicalb. A fine water mistc. Carbon dioxided. Form
55. When approaching the rear of an idlingturbo jet engine the hazard area extendsaft of the engine approximately
a. 200 feet b. 100 feetc. 50 feet d.
25 feet
56. When towing a large aircrafta. A person should be in the
cockpit to watch theobstruction
b. Person should be stationed atthe nose
c. Person should be positionedeach wing tip and theempennage
d. A person should be in thecockpit to operate brakes
57. A fuel that vaporizes too readily may
cause a. Hard startingb. Detonation c.Vapor lock d. None of these
58. The main difference between grades100 and 100LL fuel are
a. Volatility and lead contentb. Volatility, lead content and
colourc. Lead content and colourd. All of these
59. Tetra ethyl lead is added to aviationgasoline to
a. Retard the formation ofcorrosive
b. Improve the gasolineperformance in the engine
c. Dissolve the moisture in thegasoline
d. None of these
60. If the temperature of a confined liquidis held constant and its pressure istrippled, the volume will
a. Tripleb. Reduced to one third its original
volumec. Remains samed. Multiply by a fixed factor
-
7/30/2019 Paper-II ( Sets)
5/21
set -II1. Choose the correct sets of angles of setsquare of one piecea) 450 x 300 b) 300 x 900
c) 450 x 600
d) 600 x 600
2. Phantom line is used for indicating the_________ position of parta) Actual b) Hidden
c) Relative d)None of these
3. Mark the correct statementa) The arrow head length is equal todouble of its widthb) The arrow head length is equal to tripleof its widthc) The arrow head length is equal to itswidthd) None of these
4. Top view false on the
-
7/30/2019 Paper-II ( Sets)
6/21
a) Horizontal planeb) Vertical plane
c) Half in horizontal and half in Verticalplane d) All above cases may bepossible
5. Direction of rotation of external gearsarea) Opposite b) Same
c) Either a) or b) d) None ofthe above
6. S in Al-alloy designation indicatesa) Cast alloy b) Wrought alloy
c) As in b) and used for a/cstructure d) None
7. Which Al-alloy is more corrosionresistant?a) 2 S b) 3 S
c) 17 S d) 52 S
8. Al clad is generally of
a) 17 S & 24 S b) 24 S & 52 Sc) 52 S & 53 S d) 53 S & 62 S
9. Inter-crystalline corrosion is generallyoccurred ina) Al-alloy containing copper composition
b) 17 S c) 24 Sd) All of these
10. Which of the following material is usedfor spot welding?
a) Clad alloys b) 52 S Al-alloyc) Both a) & b) d) None of these
11. Natural rubber is a polymer ofa) Isoprene b) Neoprene
c) Diprene d) None of these
12. Which material is used for increasingthe hardness of natural rubber?a) Sulpher b) Phosphorus
c) Sodium d) Carbon
13. Which is the basic colour of
commercial BUNA-Sa) White b) Blackc) Red d) Green
14. GR-A is a known as BUNA-N, in whichA stands fora) Butadiene b) Acrylonitrile
c) Monovinyl d) Nitrile
15. Neoprene is designated as GR-M, inwhich M is stands
a) Monovinyl b) Chloroprenec) Acrylonitrile d) Styrene
16. GR-I designated for which type ofrubbera) Neoprene b) BUNA-S
c) BUNA-N d) Butyl
17. Which type of properties is introduced
in rubber after vulcanising process?a) Elasticity b) Strong nessc) Reduce the tackiness d)
All of these
18. A/C rivets are identified bya) Head Style b) Alloy c)Length & Diameter d)All of these
19. For accurate location of particular areaon an a/c, which of the following isnecessary?a) Water line b) Butt line c) As in a)
& b) in conjunction with station line d)None
20. Which type of corrosion is occurred instainless steel after electric arc welding?a) Pitting b) Galvanic
c) Inter crystalline d)Fretting
21. Which is most suitable for spotwelding, in stainless steel?a) Low-voltage b)High-amperagec) Low-voltage and High-amperage
d) High-voltage and Low-amperage
22. Which of the following is the Non-Magnetic?a) Inconel b) K-Monel
c) Monel d) All of these
23. SAE 13XX representsa) Magnesium Steel b) ManganeseSteel c) Silicon Steel d)Chromium Steel
24. Hot piece of metal is increased in
thickness and decreased in lengtha) Upsetting b) Down settingc) Swaging d)
Rolling
25. Which of the following have greatesttensile strength?a) Fibreglass b) Aramid
c) Carbon d) Ceramic
26. For flight equilibrium, designer tries tofix the CG
-
7/30/2019 Paper-II ( Sets)
7/21
a) and C of P togetherb) At rear of C of P
c) In front of most forward position of CPd) Along aerodynamic C of
P
27. Flight calculations are based on themagnitude and direction ofa) Lift & drag b) Weight & thrust
c) Lift & thrust d) Both a)& b)
28. The factors limiting the aspect ratio area) Structural consideration b)Drag considerationc) Lift consideration d)Both a) & b)
29. What is required to reduce the landingspeed?a) A low minimum drag coefficient
b) A small movement of C of Pc) A high max CL
d) A high value of CL3/2/CD
30. With increase in altitude pressure &temperaturea) Drops
b) Will risec) Pressure drops, temperature increases
d) Temperature drops,pressure increases
31. The disadvantage of vacuum operatedGyro is
a) At high altitude, stability is reduced dueto decrease in atmospheric pressure.b) Weight due to pipelinesc) Possibility of contamination by corrosionand dirt particles.d) All of these
32. Gyro of AC operated instrumentsutilize the principle of squirrel cageinduction motor and because of highfrequency of power supply, greater rotorspeeds are possible of approximate.
a) 23000rpm b) 24000rpmc) 24500rpm d) None
33. Indication of pitch & Bank attitude arepresented by the relative position ofa) Aircraft symbol b)Gyro stabilised bar (Horizon symbol)c) Both a) & b) d) None ofthese
34. Freedom of gimbal system movementabout the roll & pitch axes in gyro horizonis ______ respectivelya) 3600 and 900b) 3600 and 800c) 3600 and850 d) None
35. The reason for restricting pitchmovement of gyro horizon is to preventa) Gimbal error b) Gimbal lock c)
Transport wander d) None36. In single disk break, break linings areknown asa) Pucks b) Three are fix
c) Three are movable d) All above
37. When break pressure is released pistonmoves back to position with thea) Return spring force b) Hydraulicpressure c) Adjusting pind)None
38. To check the angle of the main
structural component in relation to thelongitudinal and lateral axis is known asa) Incidence check b) Dihedral check
c) Structural alignment check d)Verticality check
39. On copper and copper alloy corrosionforms on the surface asa) White powder b) Greenish film
c) Blue d)Black
40. Corrosion on the metal is due to
a) Chemical attack b) Electrochemical attackc) Both a) & b) d) None
41. During routine check, the fuselageshould be inspected fora) Corrosion b) Fretting
c) Spilage d) All ofthese
42. The truss type fuselage is covered bya) Steel sheet b) Al alloy sheet
c) Fabric d) All ofthese
43. Thermoplastic material is originallya) Hardb) Soft and pliable when exposed
to heatc) It retains the moulded shape whencooled d) All of these
44. Remoulding and reshaping cannot bedone ona) Thermosetting plastic b)Thermoplastic c) Both a) & b) d) None ofthese
-
7/30/2019 Paper-II ( Sets)
8/21
45. Plastic should be stored in bins whichare tilted ata) 200 b) 100
c) 150 d) 250
46. The operating frequency of ADF isa) 90Hz b) 90KHz c)150Hz d) 90KHz to 1800KHz
47. The ADF operates ona) LF Band b) MF Band
c) LF & MF Band d)VHF Band
48. In ADF antenna system at a pointsignal fades out this is calleda) Null position b) Figure of eight
c) Cardiod d) None of these
49. ADF receiver essentially isa) TRF receiver b) Superhetrodyne receiver
c) Double superhetrodynereceiverd) Suppressed carrier receiver
50. Types of antenna / antennas used forADF receivera) Half wave b) Full wave
c) Sense aeriald) As in c) and loop aerial
51. If a D flip-flop is to switch from 0 to 1,then input is to be kept high for at leasttime T wherea) T= t setup + t hold
b) T= t setup + t hold + tpropagation delayc) T= t setup + t hold - t propagation delay
d) T= clock period
52. JK Flip flop is dividing the inputfrequency by 2, then its condition isa) J=0, K=0 b) J=0, K=1
c) J=1, K=0 d) J=1,K=1
53. In decimal to BCD decodera) 1 input, 10 output b)10 input, 4 output
c) 4 input, 10 output d)10 input, 1 output
54. If SUB pin is high in a Adder-subtractorcircuit, then circuit is;a) Adding Two bytes
b) Subtracting input byte fromoutputc) Subtracting output byte from input d)Adding 2s complement byte to the otherbyte
55. One of the effect of negative feed backin amplifiers is toa) Increase the noise
b) Increase the harmonic distortionc) Decrease the bandwidth
d) Decrease the harmonicdistortion
56. The relationship between back emf and
applied voltage in case of a dc motor isgiven bya) Eb = V + Ia Ra b) Eb = V Ia Ra c) Eb = V d)None of these
57. The direction of rotation of dc motorcan be determined bya) Flemings right hand rule
b) Flemings left hand rulec) Lenzs law
d) Amperes law
58. An engine driven 50 Hz alternator has
a speed of 750 rpm. How many poles ithas?a) 6 poles b) 4 poles
c) 2 poles d) 8 poles
59. The frequency of emf generated by agenerator depends upon itsa) Speed b) No. of ploles c)Machine rating d) Both a) & b)
60. Two quantities are said to be in phasewith each other whena) The phase difference between twoquantities is zero degrees
b) Each of them pass through zero valuesat the same time and rise in the samedirectionc) Both a) & b)d) None of these61. Capacity of a capacitor depends upona) Separation between the plates
b) Area of platesc) Di-electric material
d) All of these62. The device used to measure very highinsulation resistance of electric cable isa) High resistance voltmeter
b) Megger / Insulation resistance
testerc) Iron vane meterd) Ammeter of high range
63. If six cells are connected in series ofeach E volts, the total voltage of thebattery will bea) 6E b) 3E
c) 4E d) 12E64. Special test equipment comprising ameter and two cables each of specificlength, is required for checking theresistance of bonding. A meter widely
-
7/30/2019 Paper-II ( Sets)
9/21
used , consists of an ohm-meter operatingona) Principle of current ratio b)Principle of voltage ratio c)None of these
65. Cell phone is used to protect the Ni-Cad battery froma) Shorting between plates
b) Thermal runawayc) Avoid leakage of electrolyte d)All of these66. Which material you select for rivetingNi-steel sheeta) Monel b) 2017-T
c) 2024-T6 d) Mildsteel67. Which one of the following rivet isready for use as received and need nofurther heat treatmenta) 2117 b) 2017-T
c) 2024 d) 1100
68. Ice-Box rivets area) 2017-T b) 2117-T
c) 2024-T d) Both a)& c)
69. The specification for universal headriveta) AN-470 b) MS-20613
c) MS-20615 d) All ofthese
70. Part No AN 470 B 3-8, indicatesa) Shank dia is 3/16
b) Rivet length is 8/32
c) Material is 5056-Al alloyd) All of the above
71. Fluid used in the Aircraft hydraulicsystems area) Vegetable b) Mineral
c) Synthetic d) All ofthese72. With pure rubber seals and hose oilused in the system isa) Mineral b) Vegetable
c) Synthetic d) All of these73. In open centre system, the number ofservices can be operated at one time is
a) One only b) Two onlyc) Any number d) All of these
74. In closed system where fixed volumepump is fitted, the system is fitted with
a) Automatic cut out value to divert pumpoutput to reservoirb) To maintain the normal built uppressurec) Both a) & b)d) None of these75. Pressure maintaining value fitted in thesystem is fora) To maintain the normal system pressure
b) To safe guard the operation of theimportant servicesc) To maintain the pressure in primaryservices at a value suitable for operation ofservicesd) Both b) & c)76. Packing is made ofa) Asbestos b) Cork c)Synthetic or natural rubber d)Felt77. Aviation gasoline is having relativedensity ofa) 0.70 b) 0.72
c) 0.80 d) 0.5
78. Re-fuller delivery line should have filterofa) 5 microns b) 8 microns
c) 4 microns d) 10microns79. Component fitted in pressurizationsystem to limit any possible negativedifferentiate pressure to a sage value isa) Safety value b) Outflow value
c) Inward relief value d) pressurecontroller.
80. Roots type blower pressurized andsend air to cabin duct by taking
a) Ram air b) Air from exhaustc) Bleed air d)None of these
SET -III
1. Duckbill pliera) Is a flat nose plier b)Is used for twisting safety wiresc) Have serrations on their jaws d)
All are correct
2. Needle nose pliers are used fora) Extracting thin/sharp components
b) Extractingnailsc) Gripping small electronic components
d) All are correct
3. i) A chisel can never cut the material allby itselfii) A die is a cutting tool
a) Only i) is correct b)Only ii) is correctc) Both i) and ii) are correct d)Neither i) nor ii) is correct
-
7/30/2019 Paper-II ( Sets)
10/21
4. Cutting edge of a chisel is generallyground to an angle ofa) 30 degrees b)70 degreesc) 90 degrees d)110 degrees
5. Various types of cut of a file area) Single cut b)
Smooth cutc) Rasp d) Both a)& b) are correct
6. Bearing strength of a material refers toa) Direct tensile load it can bearb) Resistance to tear at the point of appliedloadc) Resistance to fracture at the point ofapplied loadd) Resistance to shear
7. Characteristics of metals relating todrawing it into wire is
a) Tensile strength b)Malleability c) Ductilityd) Brittleness
8. Fusibility of a metal refer to its propertythat permitsa) Welding b)Drawing into thin sheetsc) Drawing into wires d)Good thermal conductivity
9. Aluminium alloy 1100 impliesa) Pure aluminium b)It contains 11% copper
c) It contains 111% zinc d)Heat treated alloy
10. Clad aluminium alloys are used inaircraft. They area) Lighter than other aluminium alloysb) Stronger than unclad aluminium alloysc) Easily heat treatabled) Less susceptible to corrosion11. Medium carbon steels have a carbonpercentage ofa) 0.1 0.3 b)0.3 0.5c) 0.5 1.0 d)
1.0 2.0
12. Which of the statement is correct?a) Both heat treatable & non heat treatablealuminium alloys can be strain hardenedb) Strain hardening is same as coldworkingc) Strength & hardness increases duringcold workingd) All are correct
13. Find out the wrong statementregarding titaniuma) It is highly corrosion resistant b)It maintain strength at elevatedtemperaturesc) It has good resistance to creep d)It is magnetic
14. Pitot static system have heating
elements toa) Remove moisture from the airb) Prevent ice formation
c) To permit flying at high altituded) All are correct
15. Pressure heads of pitot static systemshould not be painted, because ita) Impairs their thermal efficiency
b) May cause obstruction of orificesc) None of the above
d) Both a) and b) are correct
16. i. In cross filing, the file is moved
length wise across the workii. In draw filing, the file is moved side wiseacross the worka) Only i) is correct b)Only ii) is correctc) Both i) and ii) are correct d)Neither i) nor ii) is correct
17. A cross cut saw hasa) 4-6 teeth per inch b)6-12 teeth per inchc) 10-15 teeth per inch d) 12-18teeth per inch
18. i) For a good cut on a hard material, ablade with more teeth should be usedii) While cutting a tube, a blade should beso chosen that at least five teeth are thereon each side of the tube as it is cuta) Only i) is correct b)Only ii) is correctc) Both i) and ii) are correct d)Neither i) nor ii) is correct
19. Spiral anger bit for drilling holes inwood area) Generally 7-10 inches long
b) - one inch in diameter
c) Used only with a bow type hand braced) All are correct
20. Screw driver used when there is noclearance for normal screw driver is calleda) Closed area screw driver
b) Stubby screw driverc) Off set slot screw driver
d) Any one of the above
21. Air driven power screw driver shouldbe used
-
7/30/2019 Paper-II ( Sets)
11/21
a) For large diameter screwb) For removing screw that are jammedc) Where large number of screws are to beremoved and fitted backd) When removing screws from hardermaterial22. With regard to wrenches, find out theincorrect statementa) These are made from chrome vanadium
steelb) These are generally die castc) Wrenches are made in various shapes &sizesd) These are plated to improve theirappearance
23. Box end wrenches are useda) To loosen nuts that are exceptionallylightb) Where there is restricted spacec) For nuts that are bigger than one inchsized) When open end wrench is not available
24. Crowfoot socket wrench is used wherethe following cannot be useda) Open end wrench b)Box end wrenchc) Standard socket wrench d)All are correct
25. SAE 2340 isa) Chromium steel with 3% chromiumb) Nickel chromium steel with 0.3% carbonc) Nickel steel with 3% Nickel & 0.4%carbond) Carbon (0.4%) steel
26. During nitric acid test, if the materialshows strongly magnetic nature, then it isa) Monel metal b) Carbonsteelc) Nickel steel d)18-8 steel
27. Weldability is poorest in case ofa) Plain carbon steel b)Low carbon steelc) High carbon steel d)
Wrought iron
28. Stainless steel is corrosion resistancedue to presence ofa) Silicon b)Cobaltc) Chromium d)Manganese
29. L shaped channels are produced bya) Forging b)Extrusion
c) Machining d)Casting
30. Creep in metals isa) Elongation due to temperatureb) Temporary elongation due totemperature and stressesc) Permanent set due to stresses and hightemperature operation
d) All are correct31. Angular momentum isa) Moment of inertia b) Angularvelocityc) Product of a) & b) d) Sum of a) & b)
32. Mark the incorrect statementa) Precession is inversely proportional tothe strength & direction of applied force.b) Precession is inversely proportional tothe moment of inertia of the rotor.c) Precession is inversely proportional tothe angular velocity of the rotor.
d) None of the above
33. Control of drift, relating to horizontalgyroscopes can be achieved by:a) Calculating corrections using earth rateformula and applying them as appropriateb) Applying fixed torques & cause gyro toprocess at a rate equal & opposite to theearth rate.c) As in b) but which can be variedaccording to latituded) All of these
34. When gimbal orientation is such that
the spin axis becomes coincident with oneor the other of the axes of freedom whichserves as attitude displacement referenceis termed asa) Gimbal lock b) Gimbal Errorc)Apparent drift
35. Grip length of the bolt isa) Total length of the bolt
b) Plain shank length of the boltc) Length under the head to the end of thebolt d) None of these
36. In close tolerance bolt, force applied to
drive in isa) 10 ounce hammerb) 20 ounce hammer
c) 12 to 14 ounce hammerd) Sledge hammer
37. Special washer AC 950 and AC 955 areused where
-
7/30/2019 Paper-II ( Sets)
12/21
a) Bolt is installed at angle to surfaceb) Bolt is installed head
downc) It can be used any where
d) None of these
38. Rasp file is used fora) Hard material b) Lead,wood or leather
c) Both a) & b) d) Other materialsexcept lead, wood & leather
39. Philips screwdrivers are tapered to anangle ofa) 730 b) 530
c) 600 d) 930
40. Snaps are used toa) Support the markers head of rivets
b) To make the shop head duringrivetingc) Both a) & b) d)None of these
41. Soft solder is the combination of tinand lead in proportion ofa) 2 : 3 b) 3 : 2
c) 1 : 4 d) 4 : 1
42. Bending stress is the combination ofa) Compression and shear
b) Shear and tensionc) Compression and tension
d) Tension and shear
43. In true monocoque constructionprimary stresses is taken by
a) Skin b) Framesc) Bulkhead d)Longerons
44. The skin of semi monocoque fuselagecarriesa) No load b) Full load
c) Part of the load d) Half ofthe load
45. The longitudinal stability of aeroplaneis dependent ona) Position of C of G b)Movement of C of P on the main plane and
fuselagec) Area of the tale plane, its aspect ratio,distance from C of G d) All ofthese
46. Direction of rotation of external gearsarea) Opposite b) Samec) Either a) or b) d) None ofthe above
47. Al clad is generally of
a) 17 S & 24 S b) 24 S & 52 Sc) 52 S & 53 S d) 53 S &
62 S
48. Natural rubber is a polymer ofa) Isoprene b) Neoprene
c) Diprene d) None of these
49. Which is the basic colour ofcommercial BUNA-Sa) White b) Black
c) Red d) Green
50. Which type of corrosion is occurred instainless steel after electric arc welding?a) Pitting b) Galvanic
c) Inter crystalline d)Fretting
51. SAE 13XX representsa) Magnesium Steel b)Manganese Steel
c) Silicon Steel d) Chromium Steel
52. Hot piece of metal is increased inthickness and decreased in lengtha) Upsetting b) Down setting
c) Swaging d)
Rolling53. The factors limiting the aspect ratio area) Structural consideration b)Drag considerationc) Lift consideration d)Both a) & b)
54. The disadvantage of vacuum operatedGyro isa) At high altitude, stability is reduced dueto decrease in atmospheric pressure.b) Weight due to pipelinesc) Possibility of contamination by corrosionand dirt particles.d) All of these
55. Gyro of AC operated instrumentsutilize the principle of squirrel cageinduction motor and because of highfrequency of power supply, greater rotorspeeds are possible of approximate.
a) 23000rpm b) 24000rpmc) 24500rpm d) None
56. During routine check, the fuselageshould be inspected fora) Corrosion b) Fretting
c) Spilage d) All ofthese
57. The truss type fuselage is covered by
-
7/30/2019 Paper-II ( Sets)
13/21
a) Steel sheet b) Al alloy sheetc) Fabric d) All of
these
58. Two quantities are said to be in phasewith each other whena) The phase difference between twoquantities is zero degreesb) Each of them pass through zero values
at the same time and rise in the samedirectionc) Both a) & b)d) None of these
59. If six cells are connected in series ofeach E volts, the total voltage of thebattery will bea) 6E b) 3E
c) 4E d) 12E60. Which one of the following rivet isready for use as received and need nofurther heat treatmenta) 2117 b) 2017-T
c) 2024 d) 110061. When calculating power in a reactive orinductive ac circuit, the true power isa) More than the apparent powe
b) Less than the apparentpowerc) As in b) in reactive circuit and as in a) ininductive circuitd) None of these
62. The correct way to connect a testvoltmeter in a circuit isa) In series with the unit
b) Between the source voltage andthe loadc) In parallel with the unit
63. Transfer of electrical energy from oneconductor to another without the add ofelectrical connectionsa) is called induction b) is calledair gap transferc) Will cause excessive arching and heat,and as a result is impractical
64. Diodes are used in electrical powercircuit primarily asa) Switches b) Rectifiers
c) Relays d)Contactors65. If three resistors of 3, 5 and 22 ohmsare connected in series in a 28V circuit,how much current will flow through the 3ohms resistor?a) 9.3 amps b) 1.05 amps
c) 0.93 amps d) 10.05amps
66. What is the value of a resistance ifgiven colour codes as brown, black, brown,black and brown.a) 1010 ohms b) 1000 ohms
c) 101 ohms d) 10.1 Kohms
67. What is the value of a capacitor ifgiven colour codes are orange, orange,
blue and white.a) 33nF b) 33F c) 33pFd) 3300F
68. The output of a astable multi-vibratorisa) Triangular wave b) Sawtooth wave c) Sinusoidal wave
d) Square wave69. In an oscilloscope by varying intensitycontrol, what actually varied internally?a) Cathode voltage b) Anodevoltage c) Grid voltage d)Cathode current70. The output of NOT gate is always
a) High b) Low c)Same as inputd) Complementary of input
71. Oxy acetylene welding process issuitable for joining metal sheets and plateshaving thickness ofa) 1 to 30mm b) 2 to 50 mm
c) 2 to 40mm d) All of these
72. In oxyacetylene welding, welding rod isrequired as a filter metal when welding iscarried out above
a) 15mm b) 10mmc) 40mm d) 5mm
73. In oxyacetylene welding, neutral flameproduces a maximum temperature ofa) 30000F b) 32000F
c) 32000C d) 30000C74. Standard colour for oxygen hose isa) Black b) Red
c) Green d) None ofthese75. In magnet steel, the alloying elementsarea) Nickel, Cobalt
b) Silicon, Nickelc) Molybdenum, Copperd) Tungsten, Cobalt
76. Maximum distance between support forfluid tubing of 1/8 size of steel isa) 12 b) 14
c) 9.5 d) 11.577. MS 20004 is aa) Internal wrenching bolt
b) Close tolerance boltc) Clevis bolt
d) None of these
-
7/30/2019 Paper-II ( Sets)
14/21
78. Mark the incorrect statement,regarding K monel metala) It is ferrous alloy
b) It is used for gears and chainc) It is non ferrous alloy
d) It is corrosion resistant79. The symbol is fora) Wood b) Cast iron
c) Steel d) Rubber80. Ballast is used on a/ca) To attain the desired c.g. b)To increase the weightc) For making noseheavy d) None of these
1. Which of these is indicator ofelasticity & plasticity both?a) Rockwell hardness test
b) Brinell hardnesstest
c) Shore Scleroscoped) Vickers hardnesstest
2. Flattening test isa) Bending test b) Only forcopper wires c) For tubetesting d) Both a) & c)
3. Max rate of bending perminute in reverse bend test is
a) 50 b) 60c) 10 d) 40
4. Izod test measuresa) Toughness b)Height of upswing c)Energy in breaking d)Hardness
-
7/30/2019 Paper-II ( Sets)
15/21
5. Fatigue test is fordetermininga) Stress in material b)Strain in rodc) Stress limit for material d)Elongation of wire
6. Torsion test is essential fora) Wires b) Tube
c) Rods d) Sheet
7. Bending test indicatesa) Ductility b) Brittleness
c) Hardnessd) Density
8. 250 HB 10 indicatesa) Strength only b) Hardnessonly c) Both a) & b) d)Toughness
9. Unit of tension isa) N b) N/m
c) KN/m2 d)Kg/cm2
10. First usable ferrous product
obtained by smelting ores in ablast furnace isa) Pig Iron
b) Wrought Ironc) Cast Iron
d) Steel
11. Siderite isa) Oxide ore of Iron
b) Carbonate
ore ofIronc) Sulphide ore of Irond) Flux used in
furnace
12. Coke used in blast furnace isa) Fuel
b) Flux
c) Reducing agentd) Both fuel &
reducing agent
13. In upper reduction zone, wegeta) Iron
b) Carbondioxidec) Carbon monoxide
d) Both Fe &CO2
14. Steel is alloyed to improvea) Hardenability
b) Toughnessc) Fatigue strength
d) All of theabove
15. Cast Iron sparks area) Red
b) Whitec) Straw coloured
d) First Red thenStraw coloured
16. Corrosion resistant steel
used in Aircraft construction isa) 18 8 steel
b) Mediumcarbon steelc) 18 6 steel
d) Silicon steel
. Major alloying elements ofstainless steel are ( in order of% composition)
a) Ni Cr b) Ni Vc) W Ni
d) Cr Ni
18. Forging steel isa) Low Carbon steel
b) MediumCarbon steel
-
7/30/2019 Paper-II ( Sets)
16/21
c) High Carbon steeld) Either a) or
c)
19. Exhaust collector is made upofa) Silicon steel
b) Titanium steelc) Chromium steel
d) Ni Crsteel
20. Which element isresponsible for Red hardnessproperty?a) Ti b) Ta
c) Mo d) W
21. Which elements areresponsible for Penetrationhardness?a) Mn, S b) Mn, P
c) Mn, Cr d) Cr, C
22. Stainless steel isa) Ni Cr steel b) Cr Mosteel c) Ni W steel d) Cr Va steel
23. Silicon in steel acts asa) Oxidiser b) Deoxidiser
c) Impurity d)Both b) & c)
24. Mark the correct statementa) SAE 2330 is chromium steel
b) SAE 3250 is used in making
axle shafts because of highstrengthc) SAE 3115 is used for makingpiston pins, cam rings
25. Steel is preheated beforewelding toa) Include strength b)Enhance its creep resistance
c) Enhance its creep resistance
26. Steel used for wing-hingefittings & flying wire trunnions isa) SAE 4140 b)SAE 6150 c) SAE1015
27. Steel used commercially forautomatic machine production isa) SAE 4135 b)SAE 4615 c) SAE611528. Steel used as an alternatefor SAE 4130 steel isa) SAE 8620 b)SAE 8630 c) SAE
926029. Pyrometer is used toa) Measure the temperature
b) Protect thefurnacec) Give protective atmosphere
30. The fastest rate of cooling isgiven bya) Brine b)
Oil c) Water
31. The tip of the rivet is upsetto form a second head and thatis known asa) Round head b) Shophead c) Flat head d)Brazier head
32. O ring packings are used forpreventinga) Internal leak b) Externalleak c) One direction leakd) Both a) & b)
33. Gaskets are made of
-
7/30/2019 Paper-II ( Sets)
17/21
a) Asbestos b)Copper c) Cork
d) All of these
34. While bending tubing, asmall flattening is allowed butthe small diameter of the bend
should not be less than_______ of the outsidediametera) 90% b) 25%
c) 75%d) 80%
35. Deep permanent impressionin the hose produced by thepressure of hose clamp is known
asa) Hot flow b) Deep flowc) Cold flow d)
None of these
36. In hex bolt, the length ismeasureda) Under the head to the end ofthe bolt b) Plainportion of the shankc) Total length
d) Threadedlength
37. Aircraft bolts are made ofa) Mild steel b)Stainless steel c)Aluminum alloyd) Cadmium plated nickel steelcorrosion resistance steel andaluminum alloy
38. Fluid used in the Aircrafthydraulic systems area) Vegetable b)Mineral c) Synthetic
d) All of these
39. Vegetable based fluid isnormally
a) Pink b)Yellow c) Almostcolourless d) None ofthese
40. With pure rubber seals andhose oil used in the system is
a) Mineral b) Vegetablec) Synthetic
d) All of these
41. In open centre system, thenumber of services can beoperated at one time isa) One only b) Two only
c) Any number d) All ofthese
42. When no services areoperated in open centre system,the pressure value in thesystem isa) At low value
b) At highvaluec) Pump output passes directlyto the reservoir d) Botha) & c)
43. In closed system wherefixed volume pump is fitted, thesystem is fitted witha) Automatic cut out value todivert pump output to reservoirb) To maintain the normal builtup pressurec) Both a) & b)
d) None of these
44. Thermal relief value fitted inthe hydraulic system operatesat a pressurea) Slightly higher than normalsystem pressureb) Relieve only a small quantityof fluid
-
7/30/2019 Paper-II ( Sets)
18/21
c) At lower than the systempressured) Both a) & b)
45. Pressure maintaining valuefitted in the system is fora) To maintain the normal
system pressureb) To safe guard the operationof the important servicesc) To maintain the pressure inprimary services at a valuesuitable for operation of servicesd) Both b) & c)
46. Restrictor valve fitted in thehydraulic system for
a) Allowing free flow of fluid inone direction b)Limited flow in other directionc) To control the pressured) Both a) & b)
47. Packing is made ofa) Asbestos b) Cork
c) Synthetic or naturalrubber d) Felt
48. Running seals area) Packing b) Gasket
c) Wiper d) Noneof these
49. Washer (gasket) used forspark plug isa) Asbestos b) Copper
c) Cork d) All of these
50. Gasket used on uneven orvarying space is made ofa) Asbestos b) Cork
c) Copper d) All of these
51. Seals used for cleaning andlubricating is called
a) Wiper b) Gasketc) Packing d) None
of these
52. Fuel used for turbo jetengine isa) Gasoline b) Aviation
kerosene c) Petrol d)None of these
53. Aviation gasoline is havingrelative density ofa) 0.70 b) 0.72
c) 0.80d) 0.5
54. Relative density of AVTUR
fuel isa) 0.80 b) 0.72
b) 0.75 c) 0.70d) 0.72
55. Re-fuller delivery line shouldhave filter ofa) 5 microns b) 8microns c) 4 microns
d) 10 microns
56. The source of pressurisedair in piston engine aircraft isa) Compressor b)Supercharger c) Turbocharger d) Both b) & c)
57. Component fitted inpressurisation system to limitany possible negative
differentiate pressure to a sagevalue isa) Safety value b)Outflow value c) Inwardrelief value d) pressurecontroller
58. To maintain a free flow ofventilation air within the aircraft
-
7/30/2019 Paper-II ( Sets)
19/21
when parked the component isfilled toa) Safety value b)Ground automatic relief valuec)outflow value d) Both a) &c)
59. Roots type blowerpressurised and send air tocabin duct by takinga) Ram air b) Air fromexhaust c) Bleed air
d) None of these
60. Engine driven cabincompressor which is used onturbo prop aircraft, its output
pressure is controlleda) Automatically b)Manually c) Notcontrolled d) Both a) & b)
61. The working fluid used inreciprocating engine isa) Solid fuel b)Oxidizer & Fuel c) Fuel /Air Mixture d) All of these
62. Mark the correct statementa) Turbo prop engine acceleratelarge mass of air through smallvelocity changeb) As in a) & Piston Engine alsoaccelerate large mass of airthrough small velocity changec) Turbo Jet Engine acceleratelarge mass of air through small
velocity changed) Pulse Jet Engine acceleratelarge mass of air through smallvelocity change
63. To compress the engineworking fluid, Piston Engineuses
a) Turbine driven compressorb)
Pressure rise due to combustionc) Positive displacement, pistontype compressor d) Botha) & c) are correct
64. Piston engine classifiedaccording toa) Thrust
b) No. ofstrokec) Cylinder arrangement withrespect to crank shaft d)Both b) & c)
65. Radial engine classified as
a) Upright, invertedb) Accordingto no. ofrowsc) Cylinder arranged on camshaft d) Both a) & c)
66. The emitter resistor RE in atransistor amplifier is bypassedby a capacitora) To reduce the voltage gain
b) To increase thevoltage gainc) Causes thermal runaway
d) Stabilises the Qpoint
67. A transistor is operating inthe active region. Under thisconditiona) Both the junctions are
forward-biasedb) Both the junctions arereverse-biasedc) Emitter-base junction isreverse-biased, and collector-base junction is forward-biasedd) Emitter-base junction isforward-biased, and collector-base junction is reverse-biased
-
7/30/2019 Paper-II ( Sets)
20/21
68. The potential-dividermethod of biasing is used inamplifier toa) Limit the input ac signalgoing to the base b) Makethe operating point almost
independent of c) Reduce the dc base current
d)Reduce the cost of the circuit69. For generating 1 KHz note,the most suitable circuit isa) Hartley Oscillator
b) Colpits Oscillatorc) Tuned-collector Oscillator
d) Wein-bridge
Oscillator70.To generate a 1 MHz signalthe most suitable circuit isa) Wein-bridge Oscillator
b) Phase shiftOscillatorc) Colpits Oscillator
d) Hartley Oscillator
71. Weather radar works on
a) Echo system b) LOSsystem c) VHF system
d) HF system
72. Antenna size for DME isa) 1 b)
c) /4 d)/8
73. EDAS means
a) Electrical and digital Aircraftsystemb) Electronics / digital Aircraftsystemc) Electronics digital andavionics systemd) None of these
74. The purpose of EDAS is
a) Modernise the variousAircraft system and their displaysystemb) To reduce the work load ofthe pilotc) To reduce the space in theAircraft
d) All of these
75. The satellites are placed ingeo-synchronous orbit for satcom system and they providecoverage betweena) Longitude 750
b) Between latitude750 North and Southc) Both a) & b) above
d) None ofthese
76. In ball type erection unit,rotation of holder takes placethrough reduction gear fromgyro rotor shaft, the speed ofholder being__________a) 25 rpm b) 20 rpm
c) 30 rpm d) 35 rpm
77. In torque motor andlevelling switch type of erectionsystem the supply fed to thecentre electrode isa) 25V AC b) 20V AC
c) 12V AC d) 15V AC
78. Fast Erection system issupplied witha) 28V DC b) 115V AC
c) 25V AC d) None
79. Erection rate of normalerection system isa) 50/sec b) 50/min
c) 30/min d) 30/sec
80. Erection rate of fast erectionsystem is
-
7/30/2019 Paper-II ( Sets)
21/21
a) 50/sec b) 50/minc) 30/min d) 30/sec