pancode manual

PAN

CO

DE Installation

and

Programming Manual

Release 1 August 2000

PANCODEInstallation and

Programming Manual

NOTICE

This manual describes the PANCODE Door OpeningSystem.

Additional copies of this manual may be obtained fromI.T.S Ltd. Reproduction of this manual or parts thereofwithout written permission from I.T.S is strictlyprohibited.

I.T.S. Ltd. reserves the right to modify the hardware andsoftware described in the manual without prior notice.However, changes made to the hardware or softwaredescribed do not necessarily render this publicationinvalid.

WARRANTY

In the event that the product proves to be defective inworkmanship or materials within a period of one yearfrom date of shipment, I.T.S. Ltd. shall repair or replacethe product at its discretion. Transportation will be theresponsibility of the dealer/distributor. Under nocircumstances shall I.T.S. Ltd. be liable forconsequential or special damages, loss of revenue oruser/dealer expenses arising out of or in connectionwith the use or performance of the product, whetherbased on contract, tort, or any other legalagreement.

The following shall void the above warranty:malfunctions resulting from fire, accident, neglect,abuse, or acts of God; use of improper electrical power;or repair of, tampering with or alteration of the productby anyone other than I.T.S. authorized personnel.

Pancode Installation and Programming Manual i

TABLE OF CONTENTS

1. Introduction .........................................................1-1

2. Description and Installation................................2-1

2.1 Physical Description ................................2-1

2.2 Installation Instructions............................2-3

2.2.1 AC Installation .........................................2-4

2.2.2 "Normally Open" Installation...................2-5

2.2.3 Adjacent Access-Control Device .............2-7

3. Programming.......................................................3-1

4. Specifications .......................................................4-1

1-1 Pancode Installation and Programming Manual

1. INTRODUCTION

PANCODE is a smart door unit which connects to ananalog port of a PBX or a Key System.

The PANCODE door unit is available in two models,one with a gray rugged plastic front panel, and onewith a white metal front panel.Each unit consists of a heavy-duty keypad, a speaker, amicrophone, and an electric door-lock interface.

The PANCODE door unit is fed by an external12VACpower adapter, which is also provided in this package.

The PANCODE has the following features:

Direct dialing to any extension.

Connection to the PBX as an analogextension

Door opening from any extension.

Programmable access code for door opening.

Point Of Service (P.O.S.) interface.

Pancode Installation and Programming Manual 2-1

2. DESCRIPTION ANDINSTALLATION

2.1 Physical Description andInstallation

Speaker

Microphone

Keypad

Call Button

Cancel Button

Figure 2-1. PANCODE External Appearance

The front panel of the PANCODE unit incorporatesthe speaker, the microphone, and the keypad.

Description and Installation


SpeakerConnection

MicrophoneConnection

(JP1)

ConfigurationSelectionJumper

SWLINE12VAC

DOOR

ConnectionTerminal Board

TighteningScrew

TighteningScrew

KeypadConnection

J1

Figure 2-2. PCB Description

The internal PCB incorporates a configurationselection Jumper, a terminal board, a speaker,a microphone, keypad connectors, and tighteningscrew threads.

Install the PANCODE as follows:

1. Unscrew the front panel screws, and carefullyremove the front panel. Gently disconnect thespeaker, microphone and J1 connectors. Removethe front panel completely.



2. Use the provided installation screws to mount thePANCODE back cover on a wall, near theelectrically-locked door.

3. Insert the wires through the hole on the backcover. Connect the wires to the internalconnectors, as shown in Figure 2-3.

2.2 Installation Instructions

The system enables two types of installations.

- AC the door-lock mechanism is powered bythe provided 12VAC power adapter.(For a quieter door-lock action, the providedadapter can be replaced with a 12VDC/2A poweradapter).

- Normally Open (N.O.) the PANCODEprovides a short-circuit to the DOOR terminal.The door-lock mechanism is powered by adedicated, external power adapter.This installation type is also suitable for using thePANCODE unit in conjunction withaccess-control devices, time recorders etc.

The above installation types are described in thefollowing paragraphs.



2.2.1 AC Installation


Note: Connect and wire the unit before connecting theprovided power adapter to the mains.

1. Connect the 12VAC output wires from theprovided power adapter to the 12VACterminal (see Figure 2-3).The distance between the PANCODE and thepower adapter should not exceed 10m (30ft).

2. Connect the PBX extension wires to the LINEterminal (see Figure 2-3).

3. Connect the door-lock relay wires to theDOOR terminal (see Figure 2-3).

4. Connect the push button wires to the SWterminal (optional).

5. Make sure the AC/N.O. Jumper (JP1) is set toAC mode (see Figure 2-3).

6. Connect the speaker, microphone and keypadwires to their connectors (see Figure 2-2).

Note: The red lead of the keypad flat cable must be tothe left of the connector marked J1.

7. Replace the PANCODE front panel and tightenthe front panel screws.

8. Connect the power adapter to the mains. Pleaserefer to Chapter 3 of this manual, forPANCODE programming instructions.



Push ButtonSW.

PBX Line

Door-lockRelay

12VACAdapter

(provided)

JumperJP1 (AC)

Figure 2-3. AC Wiring

2.2.2 Normally Open Installation


Note: Connect and wire the unit before connecting theprovided power adapter to the mains.

1. Connect the output wires of the 12VAC poweradapter to the 12VAC terminal (see Figure 2-5).

2. Connect the PBX extension wires to the LINEterminal (see Figure 2-5).

3. Where a dedicated power adapter is used to feedthe door-lock relay, connect it as described inFigure 2-5.

4. Connect the push button wires to the SWterminal (optional).



5. Make sure the AC/N.O. Jumper (JP1) is set toN.O. mode (see Figure 2-5).

6. Connect the speaker, microphone and keypadwires to their connectors (see Figure 2-2).

Note: The red lead in the keypad flat cable must be tothe left side of the connector marked J1.

7. Replace the PANCODE front panel and tightenthe front panel screws.

8. Connect the power adapter to the mains. Pleaserefer to Chapter 3 of this manual, for PANCODEprogramming instructions.

Push ButtonSW.

PBX Line

Door-lockRelay

12VACAdapter

(provided)

ExternalPower adapter

(dedicated)Jumper

JP1 (N.O.)

Figure 2-5. Normally Open Wiring



2.2.3 Adjacent Access-Control Device

This section describes installing an access-controldevice with an existing PANCODE, and installing aPANCODE with an existing access-control device,respectively.

Figure 2-4 below describes wiring an access-controldevice to an existing PANCODE.When activated, the access-control device supplies ashort-circuit to the PANCODE SW terminal, whichactivates the door-lock relay and opens the door.In this installation, the access-control device N.O.Output wires are connected to the PANCODE SWterminal.

WarningThe access-control device must be configured toN.O. (Normally Open) mode.

PANCODE

N.O. Output SW

Door-lockRelay

JumperJP1 (AC)

Access ControlDevice

Figure 2-4. PANCODE - Access Control - AC Wiring



Figure 2-6 below describes wiring the PANCODE toan existing access-control device. The access-controldevice opens the door and the PANCODE onlyprovides a short-circuit in its DOOR terminal.In this installation, the access-control device N.O.Input wires are connected to the DOOR terminal inthe PANCODE, and the door-lock relay wires areconnected to the DOOR connector in theaccess-control device.

PANCODE

N.O. Input

JumperJP1 (N.O.)

N.O.Output

Door-lockRelay

Access ControlDevice

Figure 2-6. Access Control PANCODEN.O. Wiring


3. PROGRAMMING

The PANCODE is programmed from an extensiontouch-tone telephone by calling the PANCODE, andby using DTMF tones.

Note: A confirmation tone is heard every time aprogramming command is entered.

Table 3-1. PANCODE Programming Table

OPERATION PROGRAMMING DEFAULT

Enter theProgrammingMode.

1. Call thePANCODEextension from anytouch-tonetelephone.

2. Wait for thePANCODE toanswer (Beep).

3. Dial *0123 toenter theprogrammingmode.

Programming thedigit which opensthe door from anyextension.

*41 + X

where:X = one digit (1-9).

8

Programming thecode to open thedoor from thePANCODEkeypad.

*41 + Code + #

where:Code = up to 4 digits(between 0-9).

9876

Programming


OPERATION PROGRAMMING DEFAULT

Programming theextension numberto be called whenpressing the button.

*43 + Ext.+ #

where:Ext. = extensionnumber to be dialed (upto 4 digits).

Programming thefirst digit of theextensionnumbers in thePBX for directdialing.

See Note below.

*44 + the first digit(s)of the extensionnumbers in the PBX(up to 4 digits)+ #

Example 1: if theextension numbers inthe PBX start with thedigit 3, then program*443#

Example 2: if theextension numbers startwith digits 2 and 3,then program *4423#

Maximum time(sec.) for theextension line tobe opened.

*62 + XX

where:XX= number ofseconds (10-99).

45

Door openingtime (sec.).

*64 + XX + #where:XX= number ofseconds.

03

Exit theProgrammingMode.

*55

Note: Make sure the first digit of the Code number is differentfrom the first digit of the PBX extension number.


4. SPECIFICATIONS

AC Power Supply 12VAC/1.6A

Line Voltage 24-72VDC

DC Leakage Current < 10A

On-hook insulationresistance between lineterminal and ground

0-100VDC > 5M100-200 VDC > 30 K500VAC/50Hz > 20K100VAC/25Hz > 100K

Ring Capacitor 0.47 F 10%

On-hook Impedance @50VDC,40VAC/25Hz>3000

Ring Detect 27-100 VAC/16-60 Hz

DC Resistance (off-hook) 24-66VDC @ 20-100mA350

Impedance (off-hook) 300-3400Hz 500-700

Imbalance Ratio 300-3400Hz > 46dB

Return Loss 300-3400Hz > 18dB

Current during Break < 700A

DTMF Transmission: Frequency Tolerance Frequency Level (high) Frequency Level (low)

1.5%-6 to 8dBm-8 to 10dBm

Inter-digit Pause Time 70-80ms

Max Current for Relay 2A

ITS29 Hametzuda Street58001 Azur, IsraelTel: +972-3-5576866Fax: +972-3-5576869URL: http://www.its-tel.come-mail: [email protected]

FRONT PAGENOTICE/WARRANTY

TABLE OF CONTENTS1. INTRODUCTION2. DESCRIPTION AND INSTALLATION2.1 Physical Description and Installation2.2 Installation Instructions2.2.1 AC Installation2.2.2 Normally Open Installation2.2.3 Adjacent Access- Control Device

3. PROGRAMMING4. SPECIFICATIONS

pancode manual

Documents