computers.toshiba-europe.com p20...

Satellite

SATELLITE P20 SATELLITE P20 SATELLITE P20 SATELLITE P20 SATELLITE P20SATELLITE P20

P20

P20

T202014-ENU

se

r’s

Ma

nu

al

User’s Manual

Choose freedom.Choose freedom.computers.toshiba-europe.comChoose freedom.

User's Manual

Satellite P20 ii

Satellite P20 Version 1 Last Saved on 30/05/2003 13:57

ENGLISH using Euro_M.dot –– Printed on 30/05/2003 as T202014-EN

Copyright © 2003 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein. TOSHIBA Satellite P20 Series Portable Personal Computer User’s Manual First edition June 2003

Disclaimer This manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for the Satellite P20 series Portable Personal Computers at the time of this manual’s production. However, succeeding computers and manuals are subject to change without notice. TOSHIBA assumes no liability for damages incurred directly or indirectly from errors, omissions or discrepancies between the computer and the manual.

Trademarks IBM is a registered trademark and IBM PC, OS/2, and PS/2 are trademarks of International Business Machines Corporation. Celeron, Intel, Intel SpeedStep, and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. MS-DOS, Microsoft, Windows and DirectX are registered trademarks of Microsoft Corporation. Centronics is a registered trademark of Centronics Data Computer Corporation. Photo CD is a trademark of Eastman Kodak. Bluetooth is a trademark owned by its proprietor and used by TOSHIBA under license. i.LINK is a trademark of Sony Corporation. Other trademarks and registered trademarks not listed above may be used in this manual.

Macrovision License of Notice This product incorporates copyright protection technology that is protected by methods and claims of certain U.S. patents and other intellectual rights owned by Macrovision Corporation, and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing uses only unless authorized by Macrovision Corporation. Reverse engineering of disassembly is prohibited.

User's Manual

Satellite P20 iii



Safety Instructions

Use the following safety guidelines to help protect yourself and your computer.

When Using Your Computer

Do not operate your portable computer for an extended period of time with the base resting directly on your body. With extended operation, heat can potentially build up in the base. Allowing sustained contact with the skin could cause discomfort or, eventually, a burn.

■ Do not attempt to service the computer yourself. Always flow installation instructions closely.

■ Do not carry a battery in your pocket, purse, or other container where metal objects (such as car keys) could short-circuit the battery terminals. The resulting excessive current follow can cause extremely high temperatures and may result in damage from burns.

■ Be sure that noting rests on your AC adapter’s power cable and that the cable is not located where it can be tripped over or stepped on.

■ Place the AC adapter in a ventilated area, such as a desk top or on the floor, when you use it to run the computer or to charge the battery. Do not cover the AC adapter with papers or other items that will reduce cooling; also, do not use the AC adapter while it is inside a carrying case.

■ Use only the AC adapter and batteries that are approved for use with this computer. Use of another type of battery or AC adapter may risk fire or explosion.

■ Before you connect the computer to a power source, ensure that the voltage rating of the AC adapter matches that of the available power source. ■ 903 115 V/60Hz in most of North and south America and some Far

Eastern countries such as Taiwan. ■ 904 100 V/50Hz in eastern Japan and 100 V/60Hz in western

Japan. ■ 905 230 V/50 Hz in most of Europe, the Middle East, and the Far

East. ■ If you use an extension cable with your AC adapter, ensure that the

total ampere rating of the products plugged in to the extension cable does not exceed the ampere rating of the extension cable.

■ To remove power from the computer, turn it off, remove the battery, and disconnect the AC adapter from the electrical out let.

■ To help avoid the potential hazard of electric shock, do not connect or disconnect any cables or perform maintenance or reconfiguration of this product during an electrical storm.

■ When setting up the computer for work, place it on a level surface.

User's Manual

Satellite P20 iv



■ Do not dispose of batteries in a fire. They may explode. Check with local authorities for disposal instructions.

■ When travelling, do not check the computer as baggage. You can put your computer through an X-ray security machine, but never put your computer through a metal detector. If you have the computer checked by hand, be sure to have a charged battery available in case you are asked to turn on the computer.

■ When travelling with the hard drive removed from the computer, warp the drive in a non-conducting material, such as cloth or paper. If you have the drive checked by hand, be ready to install the drive in the computer. Your can put the hard drive through an X-ray security machine, but never, but the drive through a metal detector.

■ When travelling, do not place the computer in overhead storage compartments where it could slide around. Do not drop your computer or subject it to other mechanical shocks.

■ Protect your computer, battery, and hard drive from environmental hazards such as dirt, dust, food, liquids, temperature extremes, and overexposure to sunlight.

■ When you move your computer between environments with very different temperature and/or humidity ranges, condensation may form on or within the computer. To avoid damaging the computer, allow sufficient time for the moisture to evaporate before using the computer.

When taking the computer from low-temperature conditions into a warmer environment or from high-temperature conditions into a cooler environments, allow the computer to acclimate to room temperature before turning or power.

■ When you disconnect a cable, pull on its connector or on its strain relief loop, not on the cable itself. As you pull out the connector, keep it evenly aligned to avoid bending any connector pins. Also, before you connect a cable make sure both connectors are correctly oriented and aligned.

■ Before you clean your computer, turn if off, unplug it from its power source, and remove the battery.

■ Handle components with care. Hold a component such as a memory module by its edges, not its pins.

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

User's Manual

Satellite P20 v



■ Do not use this product near water, for example, near a bathtub, washing bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.

■ Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

■ Do not use the telephone to report a gas leak in the vicinity of the leak.

■ Use only the power cord indicated in this manual. ■ Replace only with the same or equivalent type battery recommended

by the manufacturer. ■ Dispose of used batteries according to the manufacturer’s

instructions.

EU Declaration of Conformity

TOSHIBA declares, that the product: Satellite P20 conforms to the following Standards: Supplementary Information: “The product complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/ EEC and/or the R&TTE Directive 1999/05/EEC.” This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460 Neuss, Germany.

Canadian Regulatory Information (Canada Only) This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. Note that Canadian Department of Communications (DOC) regulations provide, that changes or modifications not expressly approved by TOSHIBA Corporation could void your authority to operate this equipment. This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la class B respecte toutes les exgences du Règlement sur le matériel brouilleur du Canada.

User's Manual

Satellite P20 vi



CD-ROM, DVD-ROM, CD-R/RW, CD-RW/DVD-ROM, DVD-R/-RW, DVD-Multi drives Safety Instruction

CD-ROM, DVD-ROM, CD-R/RW, CD-RW/DVD-ROM, DVD-R/-RW and DVD Multi drives employ a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. To prevent direct exposure to the laser beam, do not try to open the enclosure.

Location of the required label Sample shown below. Location of the label on the drive and manufacturing information may vary.

TOSHIBA CORPORATION

JAPANMINATO-KU, TOKYO 105-8001,1-1, SHIBAURA 1-CHOME

User's Manual

Satellite P20 vii



CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT”. To use this model properly, read the instruction manual carefully and keep it for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station”. To prevent direct exposure to the laser beam, do not try to open the enclosure. Use of controls or adjustments or performance of procedures other than those specified in the owner’s manual may result in hazardous radiation exposure.

VORSICHT: Dieses Gerät enthält ein Laser- System und ist als “LASERSCHUTZKLASSE 1 PRODUKT” klassifiziert. Für den richtigen Gebrauch dieses Modells lesen Sie bitte die Bedienungsanleitung sorgfältig durch und bewahren diese bitte als Referenz auf. Falls Probleme mit diesem Modell auftreten, benachrichtigen Sie bitte die nächste “autorisierte Service-Vertretung”. Um einen direkten Kontakt mit dem Laserstrahl zu vermeiden darf das Gerät nicht geöffnet werden. ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling. APPARATET BOR KUN ÅBNES AF FAGFOLK MED SÆRLIGT KENDSKAB TIL APPARATER MED LASERSTRÅLER! Indvendigt i apparatet er anbragt den her gengivne advarselsmækning, som advarer imod at foretage sådanne indgreb i apparatet, at man kan komme til at udsætte sig for laserstråling. OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER EINSTELLUNGEN ODER DAS DURCHFÜHREN VON ANDEREN VORGÄNGEN ALS IN DER BEDIENUNGSANLEITUNG BESCHRIEBEN KÖNNEN GEFÄHRLICHE STRAHLENEXPOSITIONEN ZUR FOLGE HABEN.

User's Manual

Satellite P20 viii



Description on Laser specification

The optical drive such as CD-ROM, DVD-ROM, CD-R/RW, CD-RW/DVD-ROM, DVD-R/-RW and DVD Multi drive that is used in this computer is equipped with laser. The classification label with the following sentence is affixed to the surface of the drive. CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE APPAREIL A LASER DE CLASSE 1 KLASS 1 LASER APPARAT The drive with the above label is certified by the manufacturer that the drive complies with the requirement for laser product on the date of manufacturing pursuant to article 21 of Code of Federal Regulations by the United States of America, Department of Health & Human Services, Food and Drug Administration. In other countries, the drive is certified to comply with the requirement pursuant to IEC 825 and EN60825 on class 1 laser product. This computer is equipped with the optical drive in the following list according to the model.

Manufacturer Type

Matsushita UJ-811

Matsushita SR-8177

TOSHIBA SD-C2612

TOSHIBA SD-R6112

Matsushita UJDA750TT4-A

TOSHIBA SD-R2412

TEAC 224E-85

User's Manual

Satellite P20 ix



Modem warning notice

Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point. In the event of problems, you should contact your equipment supplier in the first instance.

Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements contained in EG 201 121.

Germany - ATAAB AN005, AN006, AN007, AN009, AN010, and DE03, 04, 05, 08, 09, 12, 14, 17

Greece - ATAAB AN005, AN006 and GR01, 02, 03, 04

Portugal - ATAAB AN001, 005, 006, 007, 011 and P03, 04, 08, 10

Spain - ATAAB AN005, 007, 012, and ES01

Switzerland - ATAAB AN002

All other countries/regions

- ATAAB AN003, 004

Specific switch settings or software setup are required for each network, please refer to the relevant sections of the user guide for more details. The hookflash (timed break register recall) function is subject to separate national type approval. It has not been tested for conformity to national type regulations, and no guarantee of successful operation of that specific function on specific national networks can be given.

User's Manual

Satellite P20 x



Important Notice

Copyrighted works including, but not limited to music, video, computer program, databases are protected by copyright laws. Unless specifically permitted under applicable copyright laws, you cannot copy, modify, assign, transmit or otherwise dispose of any copyrighted work with the consent of the owner of the copyright. Please take notice that unauthorized copying, modification, assignment, transmission and disposition may be subject to claims for damages and penalties.

HTT (Hyper-Threading Technology)

This is an innovative technology created by Intel and built into all their new CPUs, including the one in this computer. It allows a CPU to do two things at once (in technical terms, to run multiple task threads from a program) which gives it a faster response time and better performance.

Not all models will come with HTT.

Bluetooth Technology

Some models of the computer will come with Bluetooth technology built into it. Bluetooth was developed jointly by Ericsson, IBM, Intel, Nokia and TOSHIBA. It uses a shortwave radio frequency to connect devices such as cell phones, personal digital assistants, and computers. Essentially, any device with a Bluetooth chip can connect to and communicate with any other device with the same type of chip as long as the two are within range of one another.

Not all models come with Bluetooth technology.

Precautions

TOSHIBA computers are designed to optimise safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read these general precautions and to note the cautions included in the text of the manual.

User's Manual

Satellite P20 xi



Stress injury Carefully read the Safety Instruction Manual. It contains information on prevention of stress injuries to your hands and wrists that can be caused by extensive keyboard use. Chapter 3, Getting Started, also includes information on work space design, posture and lighting that can help reduce physical stress.

Heat injury ■ Avoid prolonged physical contact with the bottom of the computer. If

the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time (if you rest the computer on your lap, for example) your skin might suffer low-heat injury.

■ If the computer has been used for a long time, avoid direct contact with the metal plate supporting the I/O ports. It can become hot.

■ The surface of the AC adaptor can become hot when in use. This condition does not indicate a malfunction. If you need to transport the AC adaptor, disconnect it and let it cool before moving it.

■ Do not lay the AC adaptor on a material that is sensitive to heat. The material could be damaged.

PC Card overheating Some PC cards can become hot with prolonged use. If two cards are installed, both can become hot even if only one is used extensively. Overheating of a PC Card can result in errors or instability in the PC Card operation. Also be careful when you remove a PC Card that has been used for a long time.

Pressure or impact damage Do not apply heavy pressure to the computer or subject it to strong impact. Excessive pressure or impact can damage computer components or otherwise cause malfunctions.

Mobile phone Use of mobile phones can interfere with the audio system. Computer operation is not impaired but it is recommended that a distance of 30cm be maintained between the computer and a mobile phone in use.

User's Manual

Satellite P20 xii



Central Processing Unit ("CPU") Performance Disclaimer CPU performance in your computer product may vary from specifications under the following conditions: ■ Use of certain peripheral products ■ Use of battery power instead of AC power ■ Use of certain multimedia games or videos with special effects ■ Use of standard telephone lines or low speed network connections ■ Use of complex modelling software, such as high end computer aided

design applications ■ Use of the computer in areas with low air pressure (high altitude >

1,000 meters or > 3,280 feet above sea level) ■ Use of the computer at temperatures outside the range of 5°C to 35°C

(41°F to 95°F) or > 25°C (77°F) at high altitude (all temperature references are approximate).

■ CPU performance may also vary from specifications due to design configuration.

Under some conditions, your computer product may automatically shut down. This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions. To avoid risk of lost data, always make back-up copies of data by periodically storing it on an external storage medium. For optimum performance, use your computer product only under recommended conditions. Read additional restrictions in bundled documents. Contact TOSHIBA Service and Support for more information.

LCD Display Small bright dots may appear on your TFT display when you turn on your PC. Your display contains an extremely large number of thin-filmtransistors (TFT) and is manufactured using high-precision technology. Any small bright dots that may appear on your display are an intrinsic characteristic of the TFT manufacturing technology.

CE compliance This product and the original options are designed to observe the related EMC (Electromagnetic compatibility) and safety standards. However, TOSHIBA should not guarantee that this product still observes these EMC standards if options or cables not produced by TOSHIBA are connected or implemented. In this case the persons who have connected / implemented those options / cables have to assure that the system (PC plus options / cables) still fulfils the required standards. To avoid in general EMC problems following advice should be observed: ■ Only CE marked options should be connected / implemented ■ Only best shielded cables should be connected

User's Manual

Satellite P20 xiii



Working environment This product was designed to fulfil the EMC (electromagnetic compatibility) requirements to be observed for so-called "Residential, commercial and light industry environments". TOSHIBA do not approve the use of this product in working environments other than the above mentioned "Residential, commercial and light industry environments". For example, the following environments are not approved: ■ Industrial Environments (environments with a mains voltage >230V~) ■ Medical Environments ■ Automotive Environments ■ Aircraft Environments

If this product is supplied with a network port, please refer to the paragraph "Network connection".

Any consequences resulting from the use of this product in working environments that are not approved are not the responsibility of TOSHIBA Europe GmbH. The consequences of the use of this product in non-approved working environments may be: ■ Interference with other devices or machines in the near surrounding

area ■ Malfunction of, or data loss from, this product caused by disturbances

generated by other devices or machines in the near surrounding area Therefore TOSHIBA strongly recommend that the electromagnetic compatibility of this product should be suitably tested in all non-approved working environments before use. In the case of automobiles or aircraft, the manufacturer or airline respectively should be asked for permission before use of this product. Furthermore, for general safety reasons, the use of this product in environments with explosive atmospheres is not permitted.

User's Manual

Satellite P20 xiv



Network connection (class A warning) If this product has networking capabilities and will be connected to a network, Class A radiation limits will be observed (in accordance with technical conventions). This means that if the product will be used in a domestic environment, other devices in the near surrounding may suffer interference. Consequently, please do not use this product in such environments (for example a living room), otherwise you could be held responsible for any ensuing interference.

Information on the secure use of the CD-RW

Please adhere to the following information on the use of the CD-RW to minimise the risk of unsuccessful storing process. As the storing may be unsuccessful despite your adhering to these information, for example because of a defective storing medium, you should even if the software indicates a successful storage, always check if the data has been stored successfully.

About TOSHIBA Wireless Solution

Wireless LAN Card Types The Wireless LAN Card is a wireless network card that complies with the IEEE 802.11 standard on wireless LANs (Revision B). The Wireless LAN Card supports data rates up to 11 Mbit/s. ■ Wi-Fi (Wireless Fidelity) certified by the Wireless Ethernet

Compatibility Alliance (WECA). This means that your Wireless hardware will communicate with other vendors’ IEEE 802.11 compliant wireless LAN product.

■ Fully compatible with any other wireless LAN system based on Direct Sequence Spread Spectrum (DSSS) radio technology that complies with the “IEEE 802.11 standard on wireless LANs (Revision B).

Not all models come with a built in Wireless LAN card.

Wireless LAN cards The Wireless LAN Card supports the following wireless LAN features: ■ Automatic Transmit Rate Select mechanism in the transmit range of

11, 5.5, 2 and 1 Mbit/s. ■ Frequent Channel Selection (2.4 GHz). ■ Roaming over multiple channels. ■ Card Power Management. ■ Wired Equivalent Privacy (WEP) data encryption, based on the 128 bit

RC4 encryption algorithm as defined in the IEEE 802.11 standard on wireless LANs.

User's Manual

Satellite P20 xv



Wireless Interoperability The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any Wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to: ■ The IEEE 802.11 Standard on Wireless LANs (Revision B), as defined

and approved by the Institute of Electrical and Electronics Engineers. ■ The Wireless Fidelity (WiFi) certification as defined by the WECA

Wireless Ethernet Compatibility Alliance.

Wireless LAN and your Health Wireless LAN products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless LAN devices however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones. Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Wireless LAN is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of Wireless LAN may be restricted by the proprietor of the building or responsible representatives of the organisation. These situations may for example include: ■ Using the Wireless LAN equipment on board of aeroplanes, or ■ In any other environment where the risk of interference to other

devices or services is perceived or identified as harmful. If you are uncertain of the policy that applies on the use of wireless devices in a specific organisation or environment (e.g. airports), you are encouraged to ask for authorisation to use the Wireless LAN device prior to turning on the equipment.

Safety Instruction for Wireless Products If your computer has wireless function, all safety instructions must be read carefully and must be fully understood, before attempting to use our Wireless Products. This manual contains the safety instructions that must be observed in order to avoid potential hazards that could result in personal injuries or could damage your Wireless Products.

User's Manual

Satellite P20 xvi



Limitation of Liability For damage occurring due to an earthquake or thunder, fire beyond our responsibility, action by third party, other accident, intentional or accidental mistakes by a user, misuse, use under abnormal conditions, we do not take any responsibility. For incidental damage (loss of business profit, business interruption, etc.) occurring due to use or disability of the product, we do not take any responsibility. For damage occurring due to non observance of the contents described in the instruction manual, we do not take any responsibility. For damage occurring due to erroneous operation or hang up caused by use in combination with products not related to our company, we do not take any responsibility.

Usage Restrictions Do not use the Wireless Products for controlling equipment: ■ Equipment directly linked with human life corresponds to the

following. ■ Medical equipment such as life support systems, equipment used

in operations, etc. ■ Exhaust systems for gases such as poisonous gas etc. and

exhaust systems for smoke. ■ Equipment that must be set up in compliance with various laws

such as the Fire Services Act, the Construction Standard Act, etc. ■ Equipment corresponding to that mentioned above.

■ Equipment linked with human safety or having a serious influence on the safe maintenance of public function, etc., because it is not designed or manufactured for this type of use. ■ Traffic control equipment for air, railroad, road, marine transport,

etc. ■ Equipment used in atomic power plants etc. ■ Equipment corresponding to that mentioned above.

User's Manual

Satellite P20 xvii



WARNING

Turn OFF the Wireless Communication switch of Wireless Products in a congested place, such as a crowded commuter train. Keep this product away from a cardiac pacemaker at least 22cm. Radio waves can potentially affect cardiac pacemaker operation, thereby causing respiratory troubles. Turn OFF the Wireless Communication switch inside a medical facility or near medical electric equipment. Do not bring medical electric equipment close to the product. Radio waves can potentially affect medical electric equipment, thereby causing an accident due to malfunction. Turn OFF the Wireless Communication switch near an automatic door, fire alarm or other automatic control equipment. Radio waves can potentially affect automatic control equipment, thereby causing an accident due to malfunction. Do not turn ON the Wireless Communication switch in aircraft or in places that generate or can generate radio interference. Radio waves can potentially affect them, causing an accident due to malfunction. Monitor possible radio interference or other troubles to other equipment while the product is used. If any effect is caused, turn OFF the Wireless Communication switch. Otherwise, radio waves can potentially affect other equipment, thereby causing an accident due to malfunction. When using the product in a car, check with the automobile dealer if the car has an adequate electromagnetic compatibility (EMC). Radio waves of the product can potentially hamper safe driving. Depending on car model, the product can rarely affect car electronic equipment if it is used in a car.

NOTE

Do not use the product in the following places: Places near a microwave oven where a magnetic field generates and places where static electricity or radio interference generates. Depending on environment, radio waves can not reach to the product.

User's Manual

Satellite P20 xviii



Regulatory Information The TOSHIBA Wireless LAN Mini PCI Card must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device complies with the following radio frequency and safety standards.

Canada – Industry Canada (IC) This device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.” L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit étre prét à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.

Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC with essential test suites as per standards: ■ EN 60950 Safety of Information Technology equipment ■ ETS 300 328 Technical requirements for radio equipment ■ ETS 300 826 General EMC requirements for radio equipment.

User's Manual

Satellite P20 xix



Belgium/ België/Belgique

For outdoor usage only channel 10 (2457 MHz) and 11 (2462 MHz) is allowed.

For private usage outside buildings across public grounds over less than 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for private usage outside buildings across public grounds over more than 300m. An IBPT/BIPT license is required for public usage outside building.

For registration and license please contact IBPT/BIPT.

Gebruik buiten gebouw alleen op kanalen 10 (2457 MHz) en 11 (2462 MHz). Voor privé-gebruik buiten gebouw over publieke groud over afstand kleiner dan 300m geen registratie bij BIPT/IBPT nodig; voor gebruik over afstand groter dan 300m is wel registratie bij BIPT/IBPT nodig. Voor publiek gebruik buiten gebouwen is licentie van BIPT/IBPT verplicht. Voor registratie of licentie kunt u contact opnemen met BIPT.

L’utilisation en extérieur est autorisé sur le canal 10 (2457 MHz) et 11 (2462 Mhz).

Dans le cas d’une utilisation privée, à l’extérieur d’un bâtiment, au-dessus d’un espace public, aucun enregistrement n’est nécessaire pour une distance de moins de 300m. Pour une distance supérieure à 300m un enregistrement auprès de I’IBPT est requise. Pour une utilisation publique à I’extérieur de bâtiments, une licence de I’IBPT est requise. Pour les enregistrements et licences, veuillez contacter I’IBPT.

Germany/ Deutschland

License required for outdoor installations. Check with reseller for procedure to follow

Anmeldung im Outdoor-Bereich notwendig, aber nicht genehmigungspflichtig. Bitte mit Händler die Vorgehensweise abstimmen.

User's Manual

Satellite P20 xx



France Restricted frequency band: only channels 10 and 11 (2457 MHz and 2462 MHz respectively) may be used in France. License required for every installation, indoor and outdoor installations. Please contact ART for procedure to follow.

Bande de fréquence restreinte : seuls les canaux 10 à 11 (2457 et 2462 MHz respectivement) doivent être utilisés en France.

Toute utilisation, qu’elle soit intérieure ou extérieure, est soumise à autorisation. Vous pouvez contacter I’Autorité de Régulation des Télécommuniations (http://www.art-telecom.fr) pour la procédure à suivre.

Italy/Italia License required for indoor use. Use with outdoor installations not allowed

E’necessaria la concessione ministeriale anche per l’uso interno.

Verificare con i rivenditori la procedura da seguire. L’uso per installazione in esterni non e’ permessa.

Nederland License required for outdoor installations. Check with reseller for procedure to follow

Licentie verplicht voor gebruik met buitenantennes. Neem contact op met verkoper voor juiste procedure

USA-Federal Communications Commission (FCC) This device complies with Part 15 of FCC Rules. Operation of the devices in a Wireless LAN System is subject to the following two conditions: ■ This device may not cause harmful interference. ■ This device must accept any interference that may cause undesired

operation. TOSHIBA is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this TOSHIBA Wireless LAN Mini PCI Card, or the substitution or attachment of connecting cables and equipment other than specified by TOSHIBA. The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.

User's Manual

Satellite P20 xxi



Caution: Exposure to Radio Frequency Radiation. The TOSHIBA Wireless LAN Mini PCI Card will be installed with one of two types of antennas. Both antenna types, when installed are located at the upper edge of the LCD screen. For both antennas, the radiated output power of the TOSHIBA Wireless LAN Mini PCI Card is far below the FCC radio frequency exposure limits. Nevertheless, the TOSHIBA Wireless LAN Mini PCI Card shall be used in such a manner that the potential for human contact during normal operation is minimized. In normal operating configuration, the LCD in the upright position, the distance between the antenna and the user should not be less than 20cm. Refer to the Regulatory Statements as identified in the documentation that comes with those products for additional information. Relevant transmitters include FCC IDs: CJ6PA3171WL, CJ6PA3121BT.

Taiwan

Article 14 Unless approved, for any model accredited low power radio frequency electric machinery, any company, trader or user shall not change the frequency, increase the power or change the features and functions of the original design.

Article 17 Any use of low power radio frequency electric machinery shall not affect the aviation safety and interfere with legal communications. In event that any interference is found, the use of such electric machinery shall be stopped immediately, and reusing of such products can be resumed until no interference occurs after improvement.

The legal communications mentioned in the above item refer to radio communications operated in accordance with telecommunication laws and regulations.

Low power radio frequency electric machinery shall resist against interference from legal communications or from industrial, scientific and medical radio emission electric machinery.

User's Manual

Satellite P20 xxii



Using this equipment in Japan In Japan, the frequency bandwidth of 2,400~2,483.5MHz for second generation low-power data communication systems such as this equipment overlaps that of mobile object identification systems (premises radio station and specified low-power radio station). 1. Sticker

Please put the following sticker on devices incorporating this product.

In the frequency bandwidth of this equipment, industrial device,scientific device, medical device like microwave oven, licensedpremises radio station and non-licensed specified low-powerradio station for mobile object identification system (RF-ID) that isused in product line of factories, (Other Radio Stations) are used.

1. Please make sure before using this equipment that no OtherRadio Stations are used in the neighbourhood.

2. In case that RF interference occurs to Other Radio Stationsfrom this equipment, please change promptly the frequencyfor use, place to use, or stop emitting Radio.

3. Please contact TOSHIBA Direct PC if you have a problem,such as interference from this equipment to Other RadioStations.

2. Indication The indication shown below appears on this equipment.

(1) 2.4 : This equipment uses a frequency of 2.4GHz. (2) DS : This equipment uses DS-SS modulation. (3) 4 : The interference range of this equipment is less than 40m. (4) : This equipment uses a frequency bandwidth from

2,400mhz to 2,483.5MHz. It is impossible to avoid the band of mobile object identification systems.

User's Manual

Satellite P20 xxiii



Device Authorisation This device obtains the Technical Regulation Conformity Certification and the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law and the Telecommunications Business Law of Japan. The Name of the radio equipment: MPCI3A-20/R JAPAN APPROVALS INSTITUTE FOR TELECOMMUNICATIONS EQUIPMENT

Approval Number: D01-1128JP

TELECOM ENGINEERING CENTER Approval Number: 01NY A1088 The following restrictions apply: ■ Do not disassemble or modify the device. ■ Do not install the embedded wireless module into other device.

Contents

Satellite P20 xxiv



Contents

Introduction............................................................................... xxix This guide............................................................................................. xxix Safety icons .......................................................................................... xxx Service Options .................................................................................... xxx Chapter 1 Finding Your Way Around.......................................1-1 Making Sure You Have Everything ......................................................1-1 Front With The Display Closed.............................................................1-1

CD/Digital control buttons .................................................................1-2 System status indicators ...................................................................1-3

Left Side .................................................................................................1-5 Right Side...............................................................................................1-6 Rear Side................................................................................................1-7 Bottom Side ...........................................................................................1-9 Front With The Display Open .............................................................1-10 Chapter 2 Getting Started ........................................................2-1 Selecting A Place To Work ...................................................................2-1

Creating a computer-friendly environment ........................................2-1 Keeping yourself comfortable............................................................2-2 Computer placement.........................................................................2-2 Seating and posture ..........................................................................2-2 Lighting..............................................................................................2-3 Arms and wrists.................................................................................2-3 Work habits .......................................................................................2-4 Other precautions..............................................................................2-4

Setting Up Your Computer ...................................................................2-5 Connecting the AC adapter ...............................................................2-5 Charging the battery..........................................................................2-6

Connecting A Printer.............................................................................2-7 Connecting A Mouse.............................................................................2-8

Using a USB pointing device.............................................................2-8

Satellite P20

User's Manual xxiv

Contents

Satellite P20 xxv



Using The Computer For The First Time.............................................2-9 Turning on the computer ...................................................................2-9 Using the Touch pad .......................................................................2-10 Adjusting brightness ........................................................................2-11 Hotkeys ...........................................................................................2-11 StickyKeys.......................................................................................2-13 Registering your computer ..............................................................2-13

Chapter 3 Learning The Basics ...............................................3-1 Precautions............................................................................................3-1 Computing Tips .....................................................................................3-2 Using The Keyboard..............................................................................3-3

Character keys ..................................................................................3-3 Ctrl, Fn, and Alt keys .........................................................................3-3 Function keys ....................................................................................3-3 Windows® special keys......................................................................3-4 Overlay keys ......................................................................................3-4 Using the overlay to type numeric data.............................................3-4 Using the cursor control overlay........................................................3-5

Starting A Program ...............................................................................3-5 Starting a Program from the Start menu ...........................................3-5 Starting a Program from Windows Explorer ......................................3-5 Starting a Program from the Run Command.....................................3-6

Saving Your Work..................................................................................3-6 File Names.........................................................................................3-6

Printing Your Work................................................................................3-7 Backing Up Your Files ..........................................................................3-7

Copying to a diskette.........................................................................3-7 Working with StickyKeys......................................................................3-8

Activating StickyKeys ........................................................................3-8 User-Defined Buttons ...........................................................................3-8

The Internet Button and the TOSHIBA Console Button.....................3-8 Configuring the Buttons.....................................................................3-8 Configuring the On Screen Display ...................................................3-9

Using Compact Discs And DVDs .........................................................3-9 The CD-ROM / DVD-ROM / CD-RW/DVD / DVD-R/-RW / DVD Multi drive ........................................................................................3-10 Playing compact discs ....................................................................3-10 Opening the disc tray with the computer off ...................................3-11 Caring for compact discs and DVDs ...............................................3-11

Using PC Cards ...................................................................................3-11 Inserting PC Cards ..........................................................................3-12 Removing PC Cards ........................................................................3-13 Hot swapping ..................................................................................3-13

Contents

Satellite P20 xxvi



Using SD Cards ...................................................................................3-14 Using Your Computer As A Desktop Computer ...............................3-16

Using a computer lock.....................................................................3-16 Setting Up Communications ..............................................................3-17

Connecting the modem to a telephone line.....................................3-17 Connecting your computer to a network .........................................3-18 Connecting directly to a remote computer......................................3-18 Communications parameters ..........................................................3-19 File transfer protocols......................................................................3-19

Turning Off The Computer..................................................................3-20 Caring For Your Computer .................................................................3-20

Cleaning the computer ....................................................................3-20 Moving the computer ......................................................................3-20

Restoring the pre-installed software.................................................3-21 Restoring the complete system.......................................................3-21

TOSHIBA’s Online Resources ............................................................3-21 Chapter 4 Mobile Computing...................................................4-1 TOSHIBA’s Energy-Saving Design.......................................................4-1 Managing Power Usage........................................................................4-1

Running the computer on battery power...........................................4-2 Using additional battery packs ..........................................................4-2 Maximizing battery life.......................................................................4-2

Charging Batteries ................................................................................4-3 Charging the battery..........................................................................4-3 Charging the RTC battery..................................................................4-4

Monitoring Battery Power ....................................................................4-5 Determining remaining battery power ...............................................4-5

Conserving Battery Power....................................................................4-6 What to do when the battery runs low...............................................4-6

Battery Alarms.......................................................................................4-7 Changing The Battery ...........................................................................4-8

Removing the battery ........................................................................4-8 Inserting a battery..............................................................................4-9

Disposing Of Used Batteries Safely.....................................................4-9 Travelling Tips .....................................................................................4-10

Contents

Satellite P20 xxvii



Chapter 5 Using Advanced Features ......................................5-1 Multiple Displays ...................................................................................5-1

Adjusting display settings..................................................................5-1 Using multiple displays......................................................................5-1 Setting up more than one display......................................................5-2 Multiple display properties ................................................................5-3

Playing DVDs .........................................................................................5-5 Using a CD-RW, DVD-R/-RW or DVD Multi Drive .............................5-5 About DVD-RAM................................................................................5-5

Playing CDs, DVDs And Digital Music Files With The Computer On Or Off ................................................................................................5-6

CD Mode ...........................................................................................5-6 Digital Mode ......................................................................................5-7

Using The FIR Port ................................................................................5-7 Using The TOSHIBA Remote Control ..................................................5-8 Using Wireless LAN...............................................................................5-9 Using The TOSHIBA Power Management Utility ..............................5-10 Chapter 6 Expanding & Upgrading..........................................6-1 Using External Peripherals ...................................................................6-1 Connecting A USB Keyboard ...............................................................6-2 Connecting An External USB Pointing Device....................................6-3 Connecting An External Monitor..........................................................6-4 Connecting A Television.......................................................................6-5 Connecting Audio Devices ...................................................................6-6

Connecting external speakers ...........................................................6-6 Connecting A Microphone....................................................................6-7 Connecting A Line-In ............................................................................6-7 Additional Options.................................................................................6-8

External floppy disk drive ..................................................................6-8 Module Bay Options..........................................................................6-8

Upgrading System Memory..................................................................6-9 Installing additional memory..............................................................6-9

Contents

Satellite P20 xxviii



Chapter 7 If Something Goes Wrong ......................................7-1 Problems That Are Easy To Fix ............................................................7-1 Problems When You Turn On The Computer .....................................7-2 Fixing Device-Related Problems..........................................................7-3 Memory module problems ...................................................................7-3 Power Problems ....................................................................................7-4 Keyboard Problems ..............................................................................7-5 Display Problems ..................................................................................7-6 Disk Drive Problems..............................................................................7-7 CD-ROM Drive Problems......................................................................7-9 Sound System Problems ......................................................................7-9 PC Card Problems...............................................................................7-10 Resolving PC Card Problems.............................................................7-10 Printer Problems .................................................................................7-12 Modem Problems ................................................................................7-13 Develop Good Computing Habits ......................................................7-14 If You Need Further Assistance .........................................................7-15 Appendix A Hot Keys ............................................................... A-1 Appendix B Features And Specifications ..............................B-1 Appendix C Power Cable Connectors ...................................C-1 Appendix D Display Modes .....................................................D-1 Appendix E The TOSHIBA International Warranty................ E-1 Appendix F If Your Computer Is Stolen ................................. F-1 Index ........................................................................................... F-1

Introduction

Satellite P20 xxix



Introduction

Welcome to the world of portable computing. With your new TOSHIBA Satellite computer, your work can accompany you wherever you go. Your Satellite P20 computer provides fast and easy Internet access. Microsoft® Windows® XP is already installed on your computer. It offers exciting new features and easy Internet access.

This guide

This guide introduces the computer’s features. You can: ■ Read the entire guide from beginning to end. ■ Skim through and stop when a topic interests you. ■ Use the table of contents to find specific information. If you are new to computers, or have not used a notebook computer before, read through the first couple of chapters to familiarize yourself with the parts of the computer and how to turn it on. After that, seek out whatever interests you most. Your computer comes with the following documentation: ■ This User’s Guide with information on how the computer works ■ Safety Instruction manual ■ Windows® XP documentation, which explains the features of the

operating system.

The instructions and pictures in this user’s guide concerning the operating system are based on Windows® XP. Users of other Windows® operating systems should remember that the names of some menu items and procedures may differ from those described in this guide. Please refer to your operating system documentation if you have any problems.

Satellite P20

User's Manual xxix

Introduction

Satellite P20 xxx



Safety icons

This manual contains safety instructions that must be observed in order to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. The safety cautions have been classified according to the seriousness of the risk and the following icons highlight these instructions as follows:

DANGER: This icon indicates the existence of a hazard that could result in death or serious bodily injury if the safety instruction is not observed.

WARNING: This icon indicates the existence of a hazard that could result in bodily injury if the safety instruction is not observed.

CAUTION: This icon indicates the existence of a hazard that could result in damage to equipment or property if the safety instruction is not observed.

NOTE: This icon indicates information that relates to the safe operation of the equipment or related items.

You will also come across the following two icons as you use this guide:

HINT: This icon signals a tip on using your computer.

TECHNICAL NOTE: This icon signals useful information about how your computer works and tips on, for instance, installing software and devices.

Service Options

TOSHIBA offers a full line of service options built around its warranty programs. See the warranty and service material included with your computer for registration information. If you have a need to contact TOSHIBA, see Appendix E.

Finding Your Way Around

User's Manual 1-1



Chapter 1


This chapter presents a grand tour of your Satellite computer which serves as a reference when you need to locate specific parts of the computer. You will find more detailed information on using these parts in later chapters.

Making Sure You Have Everything

Before doing anything else make sure you received everything. If any items are missing or damaged, notify your dealer immediately.

Front With The Display Closed

CD/DIGITAL MODE BUTTON DISPLAY LATCH

2ND MODULE BAY REMOTE CONTROL

RECEIVER MAIN MODULE BAY

The Display Latch keeps the display panel closed and locked. To open the computer, slide the display latch to the right and then lift the display panel.

The CD/Digital Mode Button allows you to select and play music from audio CDs or digital files using the control buttons even when the computer is turned off.

The Remote Control Receiver is the infrared port used by for the TOSHIBA Remote Control. (The Remote Control device is not supplied with all models.)

Satellite P20

User's Manual 1-1


User's Manual 1-2



The Main Module Bay allows you to play CDs and DVDs. Your computer is fitted with either a CD or DVD drive installed, depending on its configuration. You may also be able to write CDs or even DVDs. A secondary HDD or FDD may also be used in this bay.

The 2nd Module Bay is generally used for the removable battery, but it may also be used with a second Optical Media Drive.

You can purchase TOSHIBA optional HDD and optical devices in order to extend computer's function. Please get contact with your TOSHIBA dealer.

CD/Digital control buttons CD/DIGITAL MODE

BUTTON PREVIOUS NEXT PLAY/PAUSE

CD MODE INDICATOR

LED DIGITAL MODE INDICATOR LED

STOP/EJECT

The CD/Digital Mode button sets which audio playback mode to use, either audio CD or digital music file such as MP3 or Windows Media Files.

Whether your computer is turned on or off, the CD/Digital control buttons are locked by default. To unlock them, press the CD/Digital mode button for more than 3 seconds. Press the CD/ Digital mode button again for over 3 seconds to lock them again. When the CD/Digital mode is unlocked, press the CD/Digital Mode briefly to switch between CD and Digital mode. The mode indicator LEDs will tell you which mode you are in.

The other CD/Digital Control buttons function like an audio CD player’s controls and have the following functions:

Next Skips to the following track on the disc

Previous Returns to the preceding track.

Stop/Eject Stops a track that is currently playing and ejects a stopped disc.

Play/Pause Starts playing the disc or the selected digital

track, or pauses the track that is currently playing.


User's Manual 1-3



Full instructions on playing CDs, DVDs and digital music files with your computer on or off are given in chapter 5.The Eject button works in system off mode.

System status indicators POWER

DC-IN BATTERY

The DC-IN LED indicates the computer is connected to the AC adapter and it is plugged into an AC power source.

The Power LED flashes amber while the system is in Standby mode. The LED turns off when the computer is turned off or in hibernation mode.

The Battery LED indicates the battery’s current charge/ discharge status. It lights green when the battery is fully charged. It lights amber while the battery is being charged from the AC adapter. It flashes amber when the battery capacity is low.


User's Manual 1-4



MAIN HARD DRIVE MODULE BAY

SD CARD WIRELESS

COMMUNICATION

The Main Hard Drive LED indicates that the HDD is being accessed. Every time your computer runs a program, opens a file, or performs some other function in which it must access the HDD, this light goes on.

The Module Bay LED indicates that the device in either the Main or 2nd Module Bay is being accessed.

The SD Card LED indicates the computer is accessing data from an SD Card.

The Wireless Communication LED indicates the wireless LAN or Bluetooth feature is active and that you may connect to a Local Area Network.

Not all models come fitted with a wireless communication or Blutetooth device


User's Manual 1-5



Left Side

WIRELESS COMMUNICATION

SWITCH LINE-IN JACK HEADPHONE JACK

SECURITY LOCK SLOT MICROPHONE JACK VOLUME CONTROL

The Volume Control adjusts the audio volume level.

The Microphone Jack let you connect a 3.5mm three conductor mini jack microphone or other audio input device.

The Headphone Jack lets you connect stereo headphones or other audio-output devices such as external speakers. Connecting headphones or other devices to this jack automatically disables the internal speakers.

The Line-In Jack is a standard 3.5 mm mini line-in jack that enables connection of a stereo device for audio input.

Not all models come fitted with a wireless communication or Blutetooth device

The Wireless Communication Switch (for Wireless LAN or Bluetooth) turns on the wireless networking transceiver. An indicator LED on the left of the keyboard lights to indicate that wireless networking is turned on. Not all models will come with wireless LAN device or Bluetooth.

The Security Lock Slot allows you to secure your computer with a cable lock to a desk or some other object to prevent theft.


User's Manual 1-6



Right Side

USB PORTS MODEM JACK SD CARD SLOT FIR PORT

I.LINK Port PC Card Slots TV Out Port

The i.LINK (IEEE 1394) Port lets you connect devices such as digital video cameras to your computer in order to download data from them.

The i.LINK Port is not available on all configurations.

The USB (Universal Serial Bus) Ports allow you to connect USB peripherals to the computer, such as a full-size USB keyboard or a USB pointing device. There are two more USB ports on the rear of your computer.

The Modem Jack lets you connect to a standard telephone line through a Modem cable.

The two-stacked CardBus-ready PCMCIA-compatible PC Card Slots allow you to install additional devices. Each slot can accommodate one Type II PC Card. Both slots are able to install one Type III PC Card.

Keep foreign objects out of the PC Card slots. A staple or similar object that accidentally gets into a slot can damage the computer’s circuitry.

The FIR (Fast Infrared) Port is a fast infrared communication port that allows the computer system to communicate with other IR-equipped devices.

The FIR Port is not available on all models.

The TV Out Port allows you to connect to a television or TV monitor with a 4-pin S-video cable.

The SD Card Slot allows you to use install and use SD media disks, such as the kind found in digital cameras, on your computer.


User's Manual 1-7



Rear Side

PARALLEL PORT EXTERNAL MONITOR

PORT FAN VENTS

LAN JACK USB PORTS DC-IN

The LAN Jack is an RJ-45 jack for using a standard LAN cable to connect to a Local Area Network.

ACTIVITY (AMBER

LIGHT LINK (GREEN LIGHT)

There are two status indicator on the LAN Jack. The right indicator turns green when the LAN Jack is linked with the cable, and the left one flashes amber when the LAN is active.


User's Manual 1-8



The Parallel Port lets you connect a parallel printer, or other devices including ECP-compatible devices.

The two USB (Universal Serial Bus) Ports allow you to connect USB peripherals to your computer, such as a printer, keyboard or pointing device. There are two more USB ports on the right side of your computer.

USB 2.0 is a peripheral expansion standard that supports a data- transfer rate of up to 480 Mbps. USB peripherals have a single standard for cables and connectors. The USB standard allows you to install and remove USB devices while the computer is on. Switching devices without turning off the computer is called “Hot swapping.”

The External Monitor Port is a standard 15-pin VGA port for connecting an analog display such as a desktop computer monitor.

The DC-IN is where you plug in the AC adapter.

The Fan Vents help cool the computer by letting the internal fans shed heat more easily.

To prevent possible overheating of the CPU, never block the fan vents.


User's Manual 1-9



Bottom Side

MAIN MODULE BAY LOCK

BLUETOOTH/MODEM MODULE COVER FAN COVER

2ND MODULE BAY LOCK

MAIN MODULE BAY

LATCH WIRELESS LAN CARD

MODULE COVER MEMORY MODULE

COVER 2ND MODULE BAY

LATCH

The Memory Module Cover protects the system memory modules.

The Bluetooth/Modem Module Cover protects the Bluetooth device (if installed; some configurations may not have it) and the internal modem.

The Wireless LAN Card Module Cover protects the Wireless LAN Card (some configurations may not have it.)

The two Module Locks secure the modules in the Main and 2nd Module bays, preventing them from accidentally falling out if the release latches are inadvertently pressed.

The two Module Release Latches disconnect the modules from their bays. To remove the Main Module, place the closed computer upside down with its front toward you. Unlock the Module Bay lock on the Main Module Bay side, slide on the latch on the Main Module Bay side and then slide it toward the outside edge of the computer. Remove the module from its bay. Follow the same steps for the 2nd Module.


User's Manual 1-10



Always keep the Module Bay locks secured while the modules are in their bays. Never remove or insert a module without first shutting down the computer. Doing so could result in irreparable damage. Never cover the fan inlets.

Front With The Display Open

POWER BUTTON LCD SCREEN INTERNET BUTTON TOSHIBA CONSOLE

BUTTON

KEYBOARD TOUCH PAD TV OUT BUTTON

The LCD Screen is the computer’s primary display. Your computer is equipped with a 17” TFT screen with WXGA (1440 x 900) resolution.

TFT (Thin Film Transistor) is a type of LCD flat panel display screen in which each pixel is controlled by from one to four transistors. Screens with TFT technology (sometimes called active-matrix LCDs) provide better resolution than other types of flat-panel LCD displays.


User's Manual 1-11



The Power Button turns the computer on and off, or let the system enter lower power mode (Standby, Hibernation) depending on power management setting.

The Keyboard provides all the functionality of a full-size keyboard.

The front panel provides a palm rest to assist you in maintaining proper posture while using the computer.

The keyboard function keys, when used with the Fn key, activate various system functions, such as the LCD brightness control.

See chapter 3 and appendix A for more information.

The Caps Lock LED lights when you press the Caps Lock key. When this light is on, pressing a letter key on the keyboard produces an uppercase (capital) letter.

The Cursor Lock LED lights when the arrow control overlay is turned on by pressing the Fn and F10 keys simultaneously. When this light is on, pressing an overlay key moves the cursor in the direction of the reddish white arrow printed on the left front of the key instead of the letter printed on the key.

The Num Lock LED lights when the numeric keypad overlay is turned on by pressing the Fn and F11 keys simultaneously. When this light is on, pressing an overlay key displays the number printed on the right front of the key instead of the letter printed on the top of the key.

The Cursor Lock and Num Lock cannot be used at the same time.


User's Manual 1-12



TOUCH PAD

TOUCH PAD CONTROL

BUTTONS

The Touch pad is a pressure sensitive pointing device which works like a mouse to position the cursor on the screen.

The two Touch pad Control Buttons have essentially the same functions as mouse buttons. See chapter 2 for further information.


User's Manual 1-13



INTERNET BUTTON

TV OUT BUTTON TOSHIBA CONSOLE

BUTTON

The two User-Defined buttons are pre-configured as the Internet button, which opens your default web browser, and the TOSHIBA Console button, which opens the TOSHIBA Console program. Both can be assigned custom tasks, which are then triggered when one of them is pressed. The third button is for TV Out.

Getting Started

User's Manual 2-1



Chapter 2

Getting Started

This chapter provides tips for working comfortably, describes how to connect components, and explains what to do the first time you use your notebook computer.

Selecting A Place To Work

Your computer is portable and designed to be used in a variety of circumstances and locations.

Creating a computer-friendly environment Place the computer on a flat surface, which is large enough for the computer and any other items you need to use, such as a printer. Leave enough space around the computer and other equipment to provide adequate ventilation and prevent overheating. To keep your computer in prime operating condition, protect your work area from: ■ Dust, moisture, and direct sunlight. ■ Liquids and corrosive chemicals.

If you spill liquid into the computer, turn it off, unplug it from the AC power source, remove the battery, and let it dry out completely before turning it on again. If the computer does not operate correctly after you turn it back on, contact a TOSHIBA authorized service provider.

■ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones.

■ Rapid changes in temperature or humidity and sources of temperature change such as air conditioner vents or heaters.

■ Extreme heat, cold, or humidity. Use the computer within a temperature range of 5° to 35° C (40° to 95° Fahrenheit) and 20% to 80% non-condensing humidity.

Satellite P20

User's Manual 2-1

Getting Started

User's Manual 2-2



Keeping yourself comfortable Strain and stress injuries are becoming more common as people spend more time using their computers. However, with a little care and proper use of the equipment, you can work comfortably throughout the day. This section provides hints on avoiding strain and stress injuries. For more information, consult books on ergonomics, repetitive- strain injury, and repetitive-stress syndrome.

Computer placement Proper placement of the computer and external devices is important to avoid stress-related injuries. ■ Place the computer on a flat surface at a comfortable height and

distance. You should be able to type without twisting your torso or neck, and look at the screen without slouching.

■ If you are using an external monitor, the top of the display should be no higher than eye level.

■ If you use a paper holder, set it at about the same height and distance as the screen.

Seating and posture When using your computer, maintain good posture with your body relaxed and your weight distributed evenly. Proper seating is a primary factor in reducing work strain. Some people find a backless chair more comfortable than a conventional chair.

90

1

Correct posture and positioning of the computer

Whichever type you choose, use the following guidelines to adjust your chair for maximum computing comfort. ■ Position your chair so that the keyboard is at or slightly below the level

of your elbow. You should be able to type comfortably with your shoulders relaxed and your forearms parallel to the floor.

Getting Started

User's Manual 2-3



If you are using a conventional chair: ■ Your knees should be slightly higher than your hips. If necessary, use

a footrest to raise the level of your knees and ease the pressure on the back of your thighs.

■ Adjust the back of your chair so that it supports the lower curve of your spine. If necessary, use a cushion to provide extra back support. Lower-back-support cushions are available at many office supply stores.

■ Sit with your back straight so that your knees, hips, and elbows form approximately 90-degree angles when you work. Do not slump forward or lean back too far.

Lighting Proper lighting can improve the visibility of the display and reduce eyestrain. ■ Position the display panel or external monitor so that sunlight or bright

indoor lighting does not reflect off the screen. Use tinted windows or shades to reduce glare.

■ Avoid placing your computer in front of a bright light that could shine directly in your eyes.

■ If possible, use soft, indirect lighting in your computer work area.

Arms and wrists ■ Avoid bending, arching, or twisting your wrists. Keep them in a

relaxed, neutral position while typing. ■ Exercise your hands, wrists, and arms to improve circulation.

Using the computer keyboard incorrectly may result in discomfort and possible injury. If your hands, wrists, and/or arms bother you while typing, stop using the computer and rest. If the discomfort persists, consult a physician.

Getting Started

User's Manual 2-4



Work habits The key to avoiding discomfort or injury from strain is to vary your activities. If possible, schedule a variety of tasks into your working day. Finding ways to break up the routine can reduce stress and improve your efficiency. ■ Take frequent breaks to change position, stretch your muscles, and

relieve your eyes. A break of two or three minutes every half hour is more effective than a long break after several hours.

■ Avoid performing repetitive activities for long periods. Intersperse such activities with other tasks.

■ Focusing your eyes on your computer screen for long periods can cause eyestrain. Look away from the computer frequently and focus your eyes on a distant object for at least 30 minutes.

Other precautions Your Satellite computer is designed to optimise safety, minimize strain, and withstand the rigors of portability. However, you should observe certain precautions to further reduce the risk of personal injury or damage to the computer.

Avoid prolonged physical contact with the underside of the computer. If the computer is used for long periods, its case can become very warm. While the temperature may not feel too hot to the touch, if you maintain physical contact with the computer for a long time (if you rest the computer on your lap, for example), your skin might suffer low-heat injury.

Never apply heavy pressure to the computer or subject it to sharp shocks. Excessive pressure or shock can damage computer components or otherwise cause your computer to malfunction. Some PC Cards can become hot with prolonged use. If two cards are installed, both can become hot even if only one is being used. Overheating of a PC Card can result in errors or instability in its operation. Be careful when you remove a PC Card that has been used for a long period.

Getting Started

User's Manual 2-5



Setting Up Your Computer

Setting up your computer may include: ■ Connecting the AC adapter ■ Charging the battery ■ Connecting a printer ■ Connecting an alternate pointing device

Connecting the AC adapter Your computer contains a rechargeable battery pack, which needs to be charged before you can use it the first time. The AC adapter enables you to power the computer from an AC outlet and to charge the computer’s battery.

Used with the AC adapter, your Satellite computer can run on power supplies worldwide.

To connect AC power to the computer: 1. Connect the power cable to the AC adapter.

Getting Started

User's Manual 2-6



2. Plug the AC adapter into the computer’s DC-IN. DC IN

3. Connect the power cable to an AC power outlet. If the battery is being charged, the Battery LED on the system indicator panel on the front of your computer will light amber. Once the battery is fully charged the battery light turns green.

The surface of the adapter’s plastic housing may get hot as it is operating. Do not touch the plastic surface when the adapter is operating to prevent possible hazard.

To avoid electric shock, do not modify, forcibly bend, damage, place heavy objects on top of, or apply any chemical treatments to the power cable. If the power cable becomes damaged or the plug overheats, discontinue use. Never remove the power plug from the outlet with wet hands.

Using the wrong AC adapter could damage your computer. TOSHIBA assumes no liability for any damage in such cases. Never pull directly on the power cable to unplug it. Hold the power plug when removing the cable from the outlet.

Charging the battery Before you can use the battery to power the computer, you must charge it. Connect the computer to an AC power outlet using the AC adapter and power cable. The DC-IN LED on the system indicator panel on the front of the computer will light and the Battery LED will light amber. Once the battery is fully charged the Battery LED turns green. Once the computer is connected to a power outlet, you can charge the battery with the computer turned off or on. When the computer is turned off, the battery charges in about 4 hours. The battery will take considerably longer to charge (up to 12 hours or longer) if the computer is turned on and consuming a lot of power.

Once the battery is charged for the first time, avoid leaving the computer plugged in and turned off for more than a few hours at a time. Continuing to charge a fully charged battery may impact the battery.

For more information on running your computer using the battery and on maximizing the life of your battery, turn to chapter 4.

Getting Started

User's Manual 2-7



Connecting A Printer

Before connecting a printer, you need to know whether it requires a USB or a parallel interface. Check the printer’s documentation. If the printer can be switched between USB and parallel mode, choose parallel if you want to leave your USB ports free for other use. You also need a suitable printer cable which may come with your printer. If not, you can purchase one from a computer or electronics store.

Connecting the printer cable while the computer is on may damage the printer, the computer, or both.

If your printer is ECP or IEEE-compliant, make sure your printer cable is an IEEE-1284 cable.

The following instructions assume you have a printer that uses a parallel port connection, which is the most common type of printer interface. 1. Turn off the computer. 2. Connect the printer cable to the printer and to the computer’s parallel

port. 3. Plug the printer’s power cable into an AC outlet. 4. Refer to your printer documentation for additional configuration steps.

PARALLEL PORT

Getting Started

User's Manual 2-8



Connecting A Mouse

You may want to use a external mouse or trackball instead of the computer’s built-in Touch pad pointing device. Your Satellite computer supports USB-compatible pointing devices. The Touch pad remains operable even if you connect an external pointing device to the computer.

Using a USB pointing device 1. Plug the device into one of the USB ports on the computer. We

recommend right-handed users attach the device to the USB port on the right-hand side of the computer; left-handed users may find it more convenient to use one of the USB ports on the rear.

RIGHT USB PORTS REAR USB PORTS

2. The device will probably require a driver and possibly other software; install it according to the instructions that come with it.

3. Position the device where you want to use it.

You don’t have to turn off the computer to connect or disconnect USB devices.

Getting Started

User's Manual 2-9



Using The Computer For The First Time

Slide the display panel latch to the right to release it and then lift the display panel to open the computer.

Don’t force the display panel open beyond the point where it moves easily. Never lift or move the computer by grasping the display panel.

Turning on the computer 1. Make sure that the Optical Media Drive or FDD drive is empty. 2. Open the display panel. 3. If you have a printer connected to your computer, turn the printer on

and wait until it indicates it is ready. 4. Turn on the computer by momentarily pressing then releasing the

power button. When you release the power button, the Power LED on the system indicator panel comes on.

When turning on the computer for the first time, don’t turn it off until the operating system has loaded completely. Turning off the computer during its initial startup will cause an error the next time you start the computer. For more on turning off your computer safely, turn to chapter 3.

When the computer is connected to an external power source, the DC-IN LED lights. If the battery is being charged, the Battery LED lights amber. The Hard Drive LED flashes when the hard disk drive is accessed.

To avoid data loss, never turn off the computer while a drive is in use.

Getting Started

User's Manual 2-10



Using the Touch pad The Touch pad is a touch-sensitive pointing device that provides all the features of a mouse. Please refer to the following instructions on how to operate the Touch pad. The Touch pad is easily accessible by moving any of your fingers off the space bar and onto the Touch pad. Gently move your finger across the Touch pad in the direction you want the cursor to move. The pad detects the change in pressure and moves the cursor in the corresponding direction. With a conventional mouse, selections are usually made by double clicking the mouse’s left button. The Touch pad also supports this feature. It is described in detail below. If you are familiar with the operations of a mouse you may only need to skim the information below.

The Touch pad buttons have essentially the same function as mouse buttons. Clicking these buttons makes selections, drags object, or performs a variety of other functions depending on the software. To select an object, first move the pointer to the object you want to select, and then press the left button one time and release it. The functionality of these buttons depends on your software. Refer to your software user’s manuals for specific information on the Touch pad (mouse) functions. Double clicking is a common technique for selecting objects or launching programs from icons. Move the pointer over the object you wish to select, then rapidly press the left button two times. This action is commonly referred to as “double clicking on an object.” Double tapping is another technique for selecting objects or executing applications from icons. For the most part double tapping is very similar to the double clicking technique of a mouse. The difference is that instead of double clicking on a mouse button, you double tap on the pressure sensitive Touch pad to make the selection. Once the cursor has been moved over the object you want select, lightly double tap the Touch pad itself. The double tapping will select the desired item and prompt the software to perform the related operation.

Getting Started

User's Manual 2-11



Many of the functions within Microsoft Windows® series operating systems can also be launched by using single tap on the Touch pad. This single tapping will select the desired item and prompt the software to perform the related operation. When working with programs that employ a graphical user interface (GUI), such as Windows®, dragging objects from one point on the screen to another is a technique you will have to master. To drag an object, first move the pointer over the object, then press and hold down the left button. Now without releasing the button, move the object to a new location on the screen by moving your finger across the Touch pad. Once the object is in the desired position, release the button to drop the object in place.

You can change settings for the Touch pad - such as how quickly you need to click twice for the computer to recognize a ‘double-click’. Go to Start, Control Panel, then (in traditional view) Mouse.

Adjusting brightness Use the following hot key combinations to adjust the screen brightness and perform other basic functions:

Hotkeys

For a full list of hot keys turn to Appendix A.

Sound Mute Turns sounds on and off.

Instant password security

Enters screen saver mode and blanks the screen. To restore your desktop, press any key or use the Touch pad.

Power Save Modes This hot key displays the power save modes.

Standby When you press Fn + F3, the computer can

enter Standby mode.

Hibernate When you press Fn + F4 the computer can enter

Hibernate mode.

Display Selection Press Fn + F5 to change the active display

device. When you press these hot keys a dialog box appears. Only selectable devices will be displayed.

Brightness down Pressing Fn + F6 decreases the display

brightness.

Getting Started

User's Manual 2-12



Brightness up Pressing Fn + F7 increase the display

brightness.

Switch Wireless LAN function on and off

For the Hot Key to function, the master Wireless Communication switch must be turned to “on”. Check the Wireless communication LED on the system status indicator panel to confirm whether wireless communication is on or off.

Your computer may not have this function, depending on the model bought.

Touch pad On/Off Pressing Fn + F9 enables or disables the

Touch pad function. When you press these hotkeys, the current setting will change and be displayed as an icon.

Cursor keypad on/off This hot key enables/ disables the embedded

cursor keypad. Numeric lock state is logically disabled. See chapter 3 for more information.

Numeric keypad on/off

This hot key enables/ disables the embedded numeric keypad. Numeric lock state is logically enabled. See chapter 3 for more information.

Scroll Lock on/off

Change Resolution Changes the current screen resolution.

Brightness control with Fn+F6 or Fn+F7 is temporary. After the computer restarts, the brightness setting in the TOSHIBA Power Management Utility overrides it. For more on the TOSHIBA Power Management Utility, refer to chapter 5.

After the computer is restarted, the cursor keypad and numeric keypad are both turned off on the notebook keyboard.

If no screen image appears after switching displays, press the Fn + Spacebar combination again to change resolution

Getting Started

User's Manual 2-13



StickyKeys StickyKeys is the primary keyboard accessibility option. It allows the user to access Shift, Ctrl and Alt key combinations by pressing keys one after the other rather than simultaneously. For instance the Ctrl-A combination can be accessed by pressing the Ctrl key followed by the A key. You can adjust the settings for StickyKeys by clicking on Start, then Control Panel, then Accessibility. Select the Keyboard tab. Fn key also supports StickyKey function.

Registering your computer Registering your computer lets TOSHIBA keep you up-to-date with information about new products and upgrades, and also provides TOSHIBA warranty coverage. See the registration card and warranty information in the appendix section for details about the warranty options available from TOSHIBA.

Learning The Basics

User's Manual 3-1



Chapter 3

Learning The Basics

This chapter covers precautions and computing tips that you should follow when using your Satellite series computer. It also provides important information about the basic features of your system.

Precautions

■ Don’t spill liquids onto the computer’s keyboard. If you do spill a liquid that gets into the keyboard, turn off the computer immediately. Leave the computer turned off overnight to let it dry out before you use it again.

■ Don’t turn off the computer if a drive light indicates a drive is active. Turning off the computer while it is reading from or writing to a disk may damage the disk, the drive, or both.

■ Keep the computer and disks away from objects that generate strong magnetic fields, such as large stereo speakers. Information on disks is stored magnetically. Placing a magnet too close to a disk can erase important files.

Always use the Standby or Hibernate mode to power down your computer. Important files may be damaged if the computer is turned off without using the Turn Off Computer command.

Before using the Standby or Hibernate mode to power down your computer, save your files and mark sure the disk activity lights are off.

■ Scan all new files for viruses. This precaution is especially important for files you receive via diskette, email, or download from the Internet. Occasionally, even new programs you buy from a supplier may contain a computer virus. You’ll need a special program to check for viruses. Ask your dealer to help you.

Satellite P20

User's Manual 3-1

Learning The Basics

User's Manual 3-2



Computing Tips

■ Save your work frequently. Your work stays in the computer’s temporary memory until you save it to the disk. You will lose all the work done since you last saved, if, for example, a system error occurs and you must restart your computer, or your battery runs out of charge while you are working.

Some programs have an automatic save feature which you can turn on. This feature saves your file to the hard disk at preset intervals. See your software documentation for details.

■ Back up your files to floppy disks (or other removable media) on a regular basis. Label the backup copies clearly and store them in a safe place. It is easy to put off backing up because it takes time. However, if your hard disk suddenly fails, you may lose all the data on it unless you have a separate backup copy.

■ Use Error-checking and the Disk Defragmenter regularly to conserve disk space and help your computer perform at its optimal level.

To run Error-checking: 1. Click Start and open My Computer. 2. Click the drive you want to test. 3. On the File menu, click Properties. 4. On the Tools tab, under Error-checking, click Check Now. 5. Under Check disk options, select the Scan for and attempt

recovery of bad sectors check box. To run Disk Defragmenter, click Start, point to All Programs, Accessories, System Tools, and click Disk Defragmenter. Consult your Microsoft® operating system documentation for more information on these and other utilities. ■ Take frequent breaks to avoid repetitive-motion injuries and eye strain. ■ Before turning off the computer, always use the Turn Off Computer

command.

Learning The Basics

User's Manual 3-3



Using The Keyboard

Character keys Typing with the character keys is very much like typing on a typewriter, except that: ■ The space bar creates a space character instead of just passing over

an area of the page. ■ The lowercase letter I and the number 1 are not interchangeable. ■ The uppercase letter O and the number 0 are not interchangeable.

The Caps Lock key shifts the letter keys to upper case – the number and symbol keys are not affected. The Caps Lock LED on the keyboard illuminates when you press Caps Lock.

Ctrl, Fn, and Alt keys

The Ctrl, Fn, and Alt keys do different things depending on the program you are using. For more information, see your program documentation.

Function keys

The function keys (not to be confused with the Fn key) are the 12 keys at the top of the keyboard. F1 through F12 are called function keys because they perform programmed functions when pressed. Used in combination with the Fn key, function keys marked with icons execute specific functions, such as dimming the computer display and enabling the numeric keypad. See appendix A for more details of these ‘hot key’ functions.

Learning The Basics

User's Manual 3-4



Windows® special keys

WINDOWS® KEY APPLICATION KEY

The keyboard provides two keys that have special functions in Windows®. The Windows® key activates the Start menu. The Application key has the same function as the secondary (normally right-side) mouse (or Touch pad) button.

Overlay keys

The keys with numbers and symbols on the front of them form the numeric and cursor overlay. This overlay lets you enter numeric data or control the cursor as you would use the ten-key keypad on a desktop computer’s keyboard.

Using the overlay to type numeric data To turn the numeric overlay on and off, press Fn and F11 simultaneously. The numeric mode light immediately below the F11 key glows when the numeric overlay is on. You can still use the overlay keys to type alphabetic characters while the numeric overlay is on. ■ For lowercase letters, hold down Fn while you type the letters. ■ For uppercase letters, hold down both Fn and Shift while you type the

letters. To use the cursor control keys (allowing you to move the cursor up, down, left and right using the keyboard) when the numeric overlay is on, press and hold down Shift while you use the cursor control keys To return to the numeric overlay, release Shift.

Learning The Basics

User's Manual 3-5



Using the cursor control overlay To turn the cursor control overlay on and off, press Fn and F10 simultaneously. The cursor control light immediately below the F10 key glows when the cursor control overlay is on. To type alphabetic characters while the overlay is on: ■ For lowercase letters, hold down Fn while you type the letters. ■ For uppercase letters, hold down both Fn and Shift while you type the

letters. To highlight text with the cursor control overlay on, hold down Shift while you use the cursor control keys.

Starting A Program

There are three ways to start a program in Microsoft® Windows® series operating systems: from the Start menu, from Windows Explorer, or from the Run command in the Start menu.

Starting a Program from the Start menu 1. Click Start, then point to All Programs.

Microsoft® Windows® XP operating system displays the Program menu, which lists programs and program groups, If your program is listed, go to step 3; otherwise, continue with step 2.

2. Point to the program group containing the program that you want to start. Microsoft® Windows® XP operating system displays the associated program menu.

3. Click the program’s icon to start the program. To close the program, click the Close button at the upper-right corner of the program’s window.

Starting a Program from Windows Explorer If a program is not in the Programs menu, you can start it from Windows Explorer. Windows Explorer gives you a view of your computer’s contents as a hierarchy or “tree.” You can easily see the contents of each drive and folder on your computer. To use this method, you need to know the name and location of the program’s executable file (this file ends with “.exe”.) 1. Click Start, point to All Programs, then point to Accessories, and

then click Windows Explorer. ■ The left side of the window displays the disk drives and folders on

your computer. ■ The right side of the window displays the contents of the item you

click on the left. 2. To open a document or start a program, double-click its icon in the

right side of the window.

Learning The Basics

User's Manual 3-6



Starting a Program from the Run Command You can start a program from the taskbar if you know its name and location. 1. Click Start on the taskbar. 2. Click Run. 3. In the dialog box, type the command line. 4. Click OK.

Saving Your Work

Before you turn off the computer, save your work to the hard disk drive. This is one of the most important rules of computing.

Save your data even when you are using Standby, in case the battery discharges before you return to work.

Many programs offer a feature that saves documents at regular intervals, such as every 15 minutes. Check your program’s documentation to see whether it has an automatic save feature. ■ To save a file you are updating, open the program’s File menu and

click Save (a common shortcut for this in many programs is to press the Ctrl key and the ‘S’ key together). Save your work at regular intervals as you work.

■ To save the current file with a new name, choose Save As from the File menu, type a name for the file, choose a location to save it and click OK.

To make another copy of the file you are currently working with, choose Save As from the File menu and give the new file a different name.

File Names Microsoft® Windows® XP operating system supports file names of up to 255 characters. You may use all the letters and numbers on the keyboard plus the following characters: _, ^, $, ~, !, #, %, &, {, }, (, ), @, [, ], +, -, ;, and ’. The names can include spaces. If you plan to share your files with a computer using MS-DOS® or a pre-Windows® 95 version of Windows®, the file name must be no more than eight characters followed by a period and a three character extension. An MS-DOS file name may not contain a space. Most programs assign an extension that identifies the file as having a particular format. For example, Microsoft® Word saves files with a .doc extension.

Learning The Basics

User's Manual 3-7



Printing Your Work

Make sure that the Microsoft® Windows® XP operating system is set up for your printer.

You only need to setup the printer the first time you connect it. If you use more than one printer or are changing printers, you will need to setup your Microsoft® Windows® operating system to run with the additional printer(s).

1. If your printer is not on, turn it on now. 2. In the File menu of your Windows® program, click Print.

The program displays a Print dialog box similar to the one below. 3. Click the Print button.

Backing Up Your Files

Backing up your files simply means copying individual files to a floppy disk or copying entire sections of your hard disk to another media, such as a CD-R or CD-RW discs.

Copying to a diskette 1. Insert a formatted floppy disk into the FDD drive (may not exist,

depending on the configuration of your computer). 2. Double-click the My Computer icon on the Windows® desktop. 3. Double-click the drive that contains the file you want to copy. 4. Double-click the folder containing the file, then click the file you want

to copy.

Use the Ctrl or Shift keys to select more than one file.

5. Click File, then click Send To. 6. Click the icon for the diskette drive.

You can also back up a file to a diskette by clicking the file (or files) you want to backup with the secondary button, then pointing to Send To and clicking 3 ½ Floppy (A:).

Learning The Basics

User's Manual 3-8



Working with StickyKeys

StickyKeys are an accessibility option that lets you use the Windows®, ALT, SHIFT, or CTRL buttons in conjunction with other keys but by pressing them one at a time.

Activating StickyKeys 1. Press the Shift key five times in a row. The dialog box opens. 2. Click OK to activate them, or Settings to open the Settings dialog

box. You can also access the Settings dialog box by going to the Control Panel and opening Accessibility Options.

User-Defined Buttons

The two User-Defined buttons on your computer let you assign specific, custom functions to them, such as opening your email program, and Internet browser, or whatever else you can think of doing with your software collection.

The Internet Button and the TOSHIBA Console Button By default, the User-Defined buttons are configured with Internet and TOSHIBA Console functionality. The Internet button opens your default Internet web browser, while the TOSHIBA Console button opens the TOSHIBA Console.

Configuring the Buttons 1. Right-click the Easy Button software icon in your system tray

notification area. 2. From the pop-up menu, click the Configuration option. 3. Select the button you’d like to configure from the menu. 4. If you use a factory-set, pre-defined function, then select the function

you’d like to assign to that button from the list. 5. If you’d like to use a custom function, select the Application Launch

option, then Browse for the program to which you’d like to assign the button.

6. In the Caption entry box, enter the name you’d like to assign to the button. This appears on-screen when pressed.

Learning The Basics

User's Manual 3-9



Configuring the On Screen Display 1. Right-click the Easy Button software icon in your system tray

notification area. 2. From the pop-up menu, click the OnScreen Display option. 3. Click the Font button to open the Choose Font dialog box and select

the font you’d like to appear in the OSD. 4. Click the Colour button to open the Windows Colour Picker and se

the colour for the OSD text. 5. Use the Size menu to define the size of the on screen text, and the

Display box to set how long the text remains on the screen. 6. The Enable option lets you turn OSD text on and off.

Using Compact Discs And DVDs

The CD-ROM drive lets you read CD-ROM discs and play audio Compact Discs. Your computer also includes a DVD-ROM drive, allowing you to play DVDs as well as CDs. The procedures for using DVDs are the same as those described for CDs below.

EJECT BUTTON MANUAL EJECT

When inserting and removing CD-ROM and DVDROM discs, be careful not to touch the lens on the disc tray or the area around it, as this may cause the drive to malfunction or permanently damage its components.

Learning The Basics

User's Manual 3-10



The CD-ROM / DVD-ROM / CD-RW/DVD / DVD-R/-RW / DVD Multi drive

Press the eject button to open the disc tray. The eject button will open the disc tray even when the computer is off if the battery has power and the computer is in CD mode. If the computer is turned off and there is no power, use the manual eject button.

Inserting discs into the drive 1. Press the eject button to open the disc tray. 2. Pull the disc tray until it is fully open. 3. Hold the disc by its edges, ensure it is dust-free, and place it carefully

in the disc tray, with the label side up. 4. Press down on the disc until it locks on the spindle. 5. Close the disc tray.

If the disc is not seated properly when you close the disc tray, the disc might be damaged and the tray may not open fully when you press the eject button.

Removing discs from the drive 1. Press the eject button.

Do not press the eject button while the computer is accessing the CDROM/DVD-ROM drive (the Module Bay LED on the left side of the keyboard flashes when the system is accessing the disc drive). If the disc is still spinning when you open the disc tray, wait for it to stop before you remove it.

2. Pull the disc tray until it is fully open, remove the disc, and place it in its protective cover.

3. Close the disc tray.

Playing compact discs Turn to chapter 1 to learn about the CD control buttons which are located on the front of your computer. For information on playing DVDs and digital music files such like MP3s, and on playing CDs with your computer turned off, see chapter 5.

Learning The Basics

User's Manual 3-11



Opening the disc tray with the computer off When your computer is turned off, you can remove and insert CDs in two ways. You can turn your computer to CD mode by pressing the CD/Digital Mode button for more than 3 seconds and then use the eject button as normal. Alternatively, use the manual eject button: 1. Insert a slender object, such as a straightened paper clip, into the

manual eject hole.

Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer end and damage the devices.

2. Pull the disc tray until it is fully open, insert a CD, or remove it and place it in its protective cover.

3. Close the disc tray.

Caring for compact discs and DVDs ■ Store your CDs and DVDs in their original containers to protect them

from scratches and keep them clean. ■ Don’t bend a disc or place heavy objects on top of it. ■ Don’t apply a label to, or otherwise mar, the surface of a CD or DVD. ■ Hold a disc by its outside edge. Fingerprints on the surface of a disc

can prevent the drive from reading the data properly. ■ Don’t expose CDs or DVDs to direct sunlight or extreme heat or cold. ■ To clean a disc, wipe it with a clean, dry cloth—starting from the

centre of the disc and wiping toward the outward edge. Do not wipe using a circular motion. If necessary, moisten the cloth with water or a neutral cleaner (not benzene or rubbing alcohol). Let the CD dry completely before inserting it in the drive.

Using PC Cards

PC Cards expand your computer’s capabilities and usefulness. You can purchase additional PC Cards from your dealer. Most PC Cards conform to the PCMCIA (Personal Computer Memory Card International Association) standard. Your Satellite computer comes with two stacked PC Card slots and supports two types of PC Card: ■ Type II cards are typically used for fax/modems, memory storage,

network cards, etc. You can install up to two of these cards, one in each slot.

■ Type III cards are used for removable hard disks and other functions that require a larger card. You can install just one of these cards No Type II card can be installed when Type III card is installed.

Check the documentation that came with the PC Card to see if it conforms to the PCMCIA 2.1 standard, or later. Other cards may work with your computer, but are likely to be much more difficult to set up and use.

Learning The Basics

User's Manual 3-12



Inserting PC Cards PC Cards require Card and Socket Services software, which is preinstalled with Microsoft® Windows® XP. This is a set of programs that acts as a translator between the PC Card and the computer that makes hot swapping (switching cards while the computer is on) possible.

TYPE II/III PC CARD

SLOT TYPE II PC CARD SLOT

Microsoft® Windows® XP operating system provides the Card and Socket Services for your PC Card. Even if your PC Card comes with its own version of Card and Socket Services, you should use the files included in Microsoft® Windows® XP operating system. Some PC Cards do not support hot swapping. Refer to your PC Card’s manual for information.

An HDD or CD-ROM connected to a 16-bit PC card, might affect the performance of the computer’s sound system and data transmission, including slower transmission speeds and dialling errors.

1. If your PC Card does not support hot swapping, save your data and turn off the computer before inserting the PC Card. For more information, see “Hot swapping” later in this chapter.

2. Hold the PC Card with the arrow side up and the connector side toward the slot.

3. Align the card connectors with an available PC Card slot and carefully slide the card into the slot until it locks into place. There are two eject buttons, one per slot. When the PC card is seated, the eject button for that slot pops out.

4. Press the eject button to put it in its retracted position.

If you have a Type III card, insert the connector into the lower slot. If you have a Type II card, insert it into either the upper or the lower slot.

To avoid damaging the computer or the PC Card, don’t force the card into the slot.

Learning The Basics

User's Manual 3-13



Removing PC Cards 1. Double-click the Safely Remove Hardware icon in the taskbar

notification area. 2. Select the PC Card that you want to remove from the list, then click

Stop. 3. A dialog box opens, from which you select the name of the PC Card

you wish to stop. Click OK. 4. A message will appear indicating that you can safely remove the card. 5. Gently press the eject button beside the slot it occupies.

If your PC Card supports hot swapping, you can remove it at any time. However, to avoid date loss, never remove a card while it is in use. For more information, see “Hot swapping”.

The upper eject button will pop out the Type II PC Card from the upper slot. The lower button will pop out a Type II, or Type III card from the lower slot.

6. Remove the PC Card and store it properly.

PC CARD EJECT

BUTTONS

Hot swapping You can replace one PC Card with another while the computer is on. This is called “hot swapping.”

Hot swapping precautions Although you can insert a PC Card at any time, to avoid data loss do not remove a card while it is in use. Before removing a PC Card, stop it by clicking the PC Card (PCMCIA) icon on the taskbar. After the PC Card is stopped, it is safe to remove it. It is recommended not to insert or remove PC cards when system is in stand by or hibernation mode. ■ Don’t remove a hard disk card while the system is accessing it. ■ Don’t remove a network card while you are connected to a network. ■ Don’t remove a SCSI card while any of the SCSI devices connected to

it is operating.

SCSI is an acronym for Small Computer Systems Interface. A single SCSI PC Card enables you to connect several SCSI devices, such as a scanner or digital camera to your computer.

Learning The Basics

User's Manual 3-14



Using SD Cards

SD Cards are small media cards capable of dynamically storing data, similar to a floppy disk. Your computer can read from and write upon SD Cards, which are often used in devices such as digital cameras, digital video recorders, MP3 players, and others. Your computer can support the following size of SD Cards: 8/16/32/64/128/256/512MB. Do not attach stickers or labels to the card or you may cause a malfunction when it is being read or ejected.

Inserting SD Cards Hold the SD Card with the gold contact area facing down and the notched corner on the right side. Gently slide it into the SD Card slot until it clicks into place.

If the system can not recognize SD cards correctly, please format SD cards with TOSHIBA SD Memory Card Format utility.

If SD card is formatted, all of data will be erased.

Learning The Basics

User's Manual 3-15



Removing SD Cards 1. Double-click the Safely Remove Hardware icon in the taskbar

notification area. 2. Select the TOSHIBA SD Memory Card Drive from the list, then click

Stop. 3. A dialog box opens, select the TOSHIBA SD Memory Card Drive

again. Click OK. 4. A message "The 'TOSHIBA SD Memory Card Drive' device can now

be safely removed from the system." will appear. 5. Push in the card and release it to pop the card out slightly. 6. Grasp the card and remove it.

Make sure the SD Card indicator to the left of the keyboard is out before you remove the card or turn off the computer’s power. If you remove the card or turn off the power while the computer is accessing the card you may lose data or damage the card. Do not insert or remove SD Card when system is in stand by mode or hibernation mode. System may fail to recognize the card.

Learning The Basics

User's Manual 3-16



Using Your Computer As A Desktop Computer

By connecting an external monitor, external full-size keyboard, and a mouse, you can work with your notebook as if it were a standard desktop computer. An external monitor connects to the external monitor port. Any USB devices including an external keyboard and pointing device connect to any of the three USB ports. See chapter six for more details.

Using a computer lock You may want to secure your computer to a heavy object such as your desk. The easiest way to do this is to purchase a computer cable lock (pictured below).

1. Feed the cable through or around some part of a heavy object. Make sure there is no way for a potential thief to slip the cable off the object.

2. Pass the locking end through the loop. 3. Insert the cable’s locking end into the security lock slot, then rotate

the key a quarter turn and remove it; the computer is now securely locked.

SECURITY LOCK SLOT

Learning The Basics

User's Manual 3-17



Setting Up Communications

To connect to the Internet, use an online service, or communicate across the telephone lines with another computer, you need: ■ A modem (supplied with your Satellite notebook computer). ■ A telephone line. ■ A browser (supplied with your computer) or communications program. ■ An Internet Service Provider (ISP) or online service if you plan to use

the Internet.

Never connect the Modem jack to a digital line. The high current of digital lines can damage the modem.

Connecting the modem to a telephone line Before you can use the modem, you must connect it to a standard voice-grade telephone line.

Disable Call Waiting before you connect through the modem. Call Waiting interrupts data transmission.

If you use a storage device such as a CD-ROM drive or HDD connected to a 16-bit PC card, modem speed might be slow or communication might be interrupted.

1. Plug one end of a standard RJ-11 telephone cable into the modem jack.

MODEM JACK

2. Plug the other end of the RJ-11 telephone cable into the modular jack of a standard voice-grade telephone line.

The telephone cable plug may be different in your country.

Learning The Basics

User's Manual 3-18



Connecting your computer to a network To access a network: ■ You need to connect a network cable with an RJ-45 connector to the

LAN Jack. For specific information about connecting a LAN or WAN, consult your network administrator.

LAN JACK

The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding setup procedures.

When the system is in the power saving mode (Hibernate), network devices such as the modem and LAN will not function and will not maintain network connection.

■ You need a dial-up connection. Ask your network administrator for the telephone number of the network.

To set up the connection, use the New Connection Wizard: 1. Click Start and point to All Programs. 2. Point to Accessories, then to Communications, and click New

Connection Wizard.

When you are connected to a network, disable your Microsoft® Windows® operating system Standby command. The Standby command can disrupt your network connection. You can disable the Standby command in Power Options (in Control Panel) or the TOSHIBA Power Management Utility (click the icon on the taskbar).

Connecting directly to a remote computer If you are connecting directly to a remote computer or a bulletin board service (BBS), you need a general-purpose communications program. In addition, there are two things you need to know before you can connect to another computer: ■ The communications parameters. ■ The file transfer protocol (only if you are downloading or uploading

files).

Learning The Basics

User's Manual 3-19



Communications parameters There are four communications parameters: ■ Modem speed - The speed at which the modem transfers information.

Speeds are measured in bits per second. ■ Data bits - The number of bits in one character. This number is usually

seven or eight. ■ Stop bit - Indicates the end of a character. This number is usually one

or two. ■ Parity - An error-checking method, which will be set to even, odd, or

none. Communications parameters, except for the modem speed, are usually abbreviated and combined. Common examples are N81 (no parity, eight data bits and one stop bit) and E72 (even parity, seven data bits and two stop bits). You set each of these parameters in your communications program. Each parameter must be set the same on both computers or you will not be able to connect. To check your modem’s settings and communications parameters: 1. Click the My Computer icon with the secondary button, then click

Properties. Windows® operating system displays the System Properties dialog box.

2. Click the Hardware tab, then the Device Manager button. 3. Click on the modem name listed under Modems.

Windows® operating system displays your modem’s Properties dialog box. This dialog box contains information about your modem configuration and status.

File transfer protocols File transfer protocols are standards that govern how computers transfer files between modems over a telephone line. You do not really need to know anything about specific protocols-just make sure you are using the same protocols as the computer with which you are communicating.

Learning The Basics

User's Manual 3-20



Turning Off The Computer

It is a good idea to turn off your computer when you are not using it for a while. Click on Start, then click Turn Off Computer. You will be given the options to Standby, Turn Off or Restart. ■ If you have work in progress and expect to resume shortly, use your

Microsoft® Windows® operating system Standby command to save your system settings so that, when you turn on the computer again, you automatically return to where you left off. To leave the computer turned off for a longer period, use your Microsoft® Windows® operating system Turn Off command instead.

■ Never turn off the power if the hard disk drive light is on. It may damage your hard disk drive.

Closing the lid of your computer can be set to put your computer into Standby. Click on Start, Control Panel, then Power Options and select Advanced to choose your preferred setting.

Caring For Your Computer

This section gives tips on cleaning and moving your computer. For information about taking care of your computer’s battery, see “Running the computer on battery power” in chapter 4.

Cleaning the computer To keep your computer clean, gently wipe the display panel and exterior case with a lightly dampened cloth. Ask your TOSHIBA dealer for suggestions for appropriate cleaning products.

Keep liquid, including cleaning fluid, out of the computer’s keyboard, speaker grille, and other openings. Never spray cleaner directly onto the computer. Never use harsh or caustic chemical products to clean the computer.

Moving the computer Before moving your computer, even across the room, make sure that all disk activity has ended (check the system status indicator LEDs) and that all external peripheral cables are disconnected.

Don’t pick up the computer by its display/panel or by the back (where the ports are located).

Learning The Basics

User's Manual 3-21



Restoring the pre-installed software

If pre-installed files are damaged, use the Product Recovery CD-ROM.

Restoring the complete system To restore the operating system and all pre-installed software, follow the steps below.

When you reinstall the Windows® operating system, the hard disk will be reformatted and all data will be lost. Make sure YOU have a backup copy of your data, before you perform a complete system recovery.

1. Load the Product Recovery CD-ROM in the drive and turn on the computer power.

2. When “In Touch with Tomorrow TOSHIBA” appears, press the F12 key. The Boot Menu appears.

3. Use your cursor keys to select the CD-ROM/DVD drive in the display menu.

4. Follow the on-screen directions. 5. If your computer came with additional software installed, this software

can not be recovered from the Recovery CD. Re-install these applications (e.g. Works Suite, DVD Player, Games, etc) separately from other media.

TOSHIBA’s Online Resources

TOSHIBA maintains a number of online sites to which you can connect. These sites can provide information about TOSHIBA products, give help with technical questions, and keep you up to date with future upgrades. For information on contacting TOSHIBA, see Appendix E.

Mobile Computing

User's Manual 4-1



Chapter 4

Mobile Computing

This chapter covers all aspects of using your computer while travelling.

TOSHIBA’s Energy-Saving Design

TOSHIBA is a partner in the Energy Star Program and has designed this product to meet the Energy Star guidelines for energy efficiency. Your computer enters a low-power state when it is not being used, thereby conserving energy and saving money in the process. It has a number of other features that enhance its energy efficiency. Many of these energy-saving features have been set by TOSHIBA. We recommend you leave these features active, allowing your computer to operate at its maximum energy efficiency, so that you can use it for longer periods while travelling.

Managing Power Usage

Your computer’s power-saving options increase the length of time you can use the computer before you need to recharge the battery. To change the power usage mode, click Start, then click Control Panel. In Control Panel, double-click the Power Option icon (if in Category View, then first click Performance and Maintenance to make the Power Option icon appear) to display the Power Option Properties window. Select the power scheme with the most appropriate settings for your computer. Keep in mind that changing any settings on the Power Option Properties window will modify the currently selected scheme. Consult your Microsoft® Windows® operating system documentation for more information on the Power Option utility.

If the TOSHIBA Power Management Utility is installed in your computer, please run it by double-clicking its icon on the taskbar instead of the Power Option icon. You can see more information in chapter 5.

Satellite P20

User's Manual 4-1

Mobile Computing

User's Manual 4-2



Running the computer on battery power The computer uses a removable Lithium Ion (Li-ION) battery pack that provides power when you are away from an AC power source. You can recharge it many times. In addition to the removable battery, the computer has an internal real-time clock (RTC) Lithium rechargeable battery. The RTC battery powers the RTC memory, which stores your system configuration settings and the current time and date for up to a month while the computer is turned off.

Using additional battery packs If you spend a lot of time travelling and need to work for many hours without an AC power source, you may want to carry additional charged battery packs with you. You can then replace a discharged battery and continue working.

A new battery pack should be fully discharged, by running the computer solely on battery power, and recharged three times when first used.

Maximizing battery life A battery can be recharged many times. Gradually over time it will lose its ability to hold a charge. To maximize the life of your battery: ■ If you are not going to use the computer for a long period of time,

remove the battery. ■ Alternate between battery packs if you have a spare. ■ Make sure the computer is off when you are replacing the battery. ■ Store spare battery packs in a cool dry place out of direct sunlight.

Mobile Computing

User's Manual 4-3



Charging Batteries

The battery needs to be charged before you can use it to power the computer. You can charge the battery using your computer.

Charging the battery To charge the battery while it is in your computer, plug the computer into a live AC outlet. It takes approximately 4 hours to charge the battery to full while the computer is off. It takes up to 12 hours or longer to charge the battery to full while the computer is on -how long depends on what other operations the computer is performing.

The battery only can charge a small current while the computer is consuming full power.

The battery may not start charging immediately if: ■ The battery is extremely hot or cold.

To ensure that the battery charges to its full capacity, wait until it reaches room temperature: 5°C to 35°C. (41°F to 95°F).

■ The battery is almost completely discharged. Leave the power connected, and the battery should begin charging after a few minutes.

Once a battery pack is fully charged, we recommend that you operate your computer on battery power until the battery pack discharges completely. Doing this extends battery life and helps ensure accurate monitoring of battery capacity.

Mobile Computing

User's Manual 4-4



Charging the RTC battery In addition to the main battery, the computer contains an internal battery for the real-time clock (RTC). The RTC battery provides power for the internal real-time clock and calendar. During normal use, the main battery keeps the RTC battery adequately charged. Occasionally, the RTC battery may lose its charge completely, especially if you have had the computer turned off and without the main battery pack inserted for a long time. In this event, your computer displays the following error message: ERROR 0271: Check data and time settings WARNING 0251: System CMOS checksum bad - Default configuration used Press <F1> to resume, <F2> to Setup. It is seldom necessary to charge the RTC battery because it charges while the computer is on. However, if the RTC battery is low, the real-time clock and calendar may display the incorrect time and date or stop working. To recharge the RTC battery, plug the AC adapter into the computer for at least 24 hours. The computer can be used while the RTC battery is being charged. Although the charging status of the RTC battery cannot be monitored, if the power is on, it takes approximately 24 hours to fully charge the RTC battery.

Mobile Computing

User's Manual 4-5



Monitoring Battery Power

The Battery LED indicates the battery’s current charge status. It lights green when the battery is fully charged. It lights amber while the battery is being charged from the AC adapter. It flashes amber when the battery capacity is low. When the light is off, the battery is discharging.

BATTERY LED

Determining remaining battery power

Wait at least 20 seconds after turning on the computer before checking the remaining battery power. The computer needs this time to check the battery’s remaining capacity and perform calculations.

To check the battery level, you can look at the TOSHIBA Power Management Utility, which can be found in the Windows® Control Panel. To access the panel: 1. Click on the Start button, then click the Control Panel. 2. Double-click the TOSHIBA Power Management Utility icon (if in

Windows® XP Category View, first click Performance and Maintenance to make the TOSHIBA Power Management Utility icon appear.)

3. Choose the Battery Power Meter tab to show the current battery status.

The computer drains the battery faster at low temperatures. Check your remaining charge frequently if you are working in temperatures below 10 degrees Celsius (50 degrees Fahrenheit). The computer calculates the remaining battery charge based on your current rate of power use and other factors such as the age of the battery.

Before removing or after inserting the battery pack, click the TOSHIBA Power Management Utility to show the latest battery status. Always ensure the computer is turned off before removing the battery pack.

Mobile Computing

User's Manual 4-6



Conserving Battery Power

How long a fully charged battery pack lasts when you are using the computer depends on a number of factors, such as: ■ How is the computer configured? ■ How much do you use the display panel instead of an external

monitor? ■ How much do you use the hard disk and other drives? ■ Do you use any optional devices that the battery supplies power to,

such as a PC Card? ■ What are your working conditions (operating time decreases at low

temperatures)? See earlier in this chapter for information on maximizing battery life.

What to do when the battery runs low When the battery runs low you have these options: ■ Plug the computer into a live AC outlet and recharge the battery. ■ Save your work and turn off the computer. If you don’t manage to do any of these things before the battery completely runs out of power, the computer automatically enters Hibernate mode and keeps track of where you were so that when you turn on the power by using AC adapter again, you can continue where you left off. (You can configure the computer to enter Standby mode instead. The default setting is Hibernate.)

When the battery capacity is below 5%, the system is protected and can’t be re-powered on without the AC power being connected. In this situation, the Battery LED will light amber for a short time to indicate this condition. Keep depressing the power button, and the LED will blink amber .

Mobile Computing

User's Manual 4-7



Battery Alarms

The computer can be configured to warn you when the battery is running low. You can set each of the following alarms: ■ Low Battery ■ Critical Battery Each alarm can be set to alert you when a specified percentage of remaining battery power has been reached. You can also set how the alarm action occurs – sound an alarm, display a message, both, or none. You can also set the computer to enter Standby when the alarm goes off. To set the alarm levels: 1. Click the Start button, then click Control Panel. 2. Double-click the TOSHIBA Power Mangement icon (if in Category

View, then first click Performance and Maintenance to make the TOSHIBA Power Mangement icon appear).

3. Click the Alarms tab. 4. Set the alarm levels as desired. For more information on battery alarms, refer to the Microsoft® Windows® operating system documentation or Help.

For more about TOSHIBA Power Mangement Utility, see Chapter 5

Mobile Computing

User's Manual 4-8



Changing The Battery

When your battery runs out of power, you have two options- connect the AC adapter or install a fresh battery. For instructions on using the AC adapter, see “Connecting the AC adapter” in chapter 2.

Removing the battery 1. Save your work. 2. Turn off the computer. Never remove the battery while the computer is

on. 3. Close the display panel, ensuring that it snaps in to place. 4. Turn the computer upside down with the front of the computer facing

towards you. 5. Unlock the 2nd Module Bay Lock. 6. Slide the 2nd Module Release Latch toward the right. 7. Pull the battery carefully out of the 2nd Module Bay.

The2nd Module Bay Latch is spring-loaded and will snap back into place when you release it.

Mobile Computing

User's Manual 4-9



Inserting a battery 1. Slide the battery into the 2nd Module Bay. When it is fully inserted,

you should hear it click into place (1).

The2nd ModuleBay Latch is spring-loaded and clicks as it latches the battery in place when you insert it.

2. Turn the computer bottom side up and ensure the battery is fully inserted in the bay. Also make sure that the 2nd Module Bay Latch is secured to the left (2).

3. Secure the 2nd Module Bay Lock (3).

If the battery housing is leaking or cracked, put on protective gloves to handle it and discard it immediately following the advice in the following section on “Disposing of Used Batteries Safely”.

The battery can only be inserted into the 2nd Module Bay.

Disposing Of Used Batteries Safely

You can recharge a battery many times. When the useful life of the battery expires or if the battery becomes damaged, you must discard it responsibly. Batteries should not be disposed of together with household waste. To make sure that they are forwarded to recycling or proper disposal they may be returned free of charge to an authorized TOSHIBA dealer/distributor. Use only batteries recommended by TOSHIBA as replacements.

The computer uses a Li-Ion battery which can explode if not handled or disposed of properly. Putting spent batteries in the trash is not only irresponsible, it may also be illegal. Dispose of the battery as required by local ordinances or regulations.

Mobile Computing

User's Manual 4-10



Travelling Tips

Environmental precautions also apply on journeys. ■ Do not leave your computer exposed to direct sunlight for long

periods of time – for instance, on the dashboard of a car – or place it where it could get wet or covered in dust.

■ Always travel with the computer in a carrying case. TOSHIBA offers a choice of carrying cases for the computer. They all provide plenty of extra space for manuals, power cables, CDROM discs, and floppy disks, etc. See your dealer for more information.

When travelling by air, you maybe required to put your notebook through airport security The X-ray equipment used may or may not harm your computer.

Ensure your personal computer is turned off before you put it in your bag.

Using Advanced Features

User's Manual 5-1



Chapter 5


This chapter explains many advanced features of your notebook computer.

Multiple Displays

Adjusting display settings You can adjust your display settings in Display Properties. Enter through Start, Control Panel, Appearance and Themes, Display or, right-click on the Windows® desktop then check Properties. Alternatively, right-click on the display icon on the taskbar (if visible), choose Settings then Display Settings. Following the on screen display step by step panels, you will be able to adjust the appearance of your desktop. You will also be able to configure your computer to use more than one display. Follow the instructions on the next two pages.

Using multiple displays Your computer can be simultaneously connected to a computer monitor and television display while also using the built-in panel display. These displays can be configured to mirror each other, or they can be arranged as separate portions of a single desktop.

For information on how to attach a television and computer monitor to your computer, please see chapter 6.

Make sure the computer is turned off before connecting an external monitor or television.

Satellite P20

User's Manual 5-1


User's Manual 5-2



Setting up more than one display Make sure that the display device is connected and select the Settings tab in Display Properties. Click on Advanced and select GeForce FX Go5200. Click nView Display Mode in the menu on the left side by clicking the tab. The display devices attached to your computer will be shown. If not, click Detect Displays. If the nView tab is not visible when you click Advanced, turn first to the instruction on the next page.

1. If you have more than one external display attached to your computer, select the displays you want to use by right-clicking on either of the pictures in the above window and selecting Select Output Device.

2. Select the display mode you want to use. You have the option of configuring both displays as clones (so that the image on one is exactly mirrored on the other) or configuring the two displays as a single desktop. This has the advantage of greatly expanding the desktop area, allowing you to, for instance, play a DVD on the television screen while running a word processor on the computer’s built-in display

After selecting your preferred display mode, Click Apply.


User's Manual 5-3



Multiple display properties If the nView tab is not visible when you click the Advanced button on the Settings tab of the Display Properties window, you must adjust your settings before using nView. Disable your existing dual monitor settings under the Settings tab by doing the following.

1. Click on the monitor icon marked 2. Make sure that the Extend my Windows desktop onto this monitor box is not checked.

2. Click on the monitor icon marked 1 and then click Apply. When the new settings have taken effect, make sure that monitor icon 1 is highlighted and click Advanced. The nView tab should now be accessible.


User's Manual 5-4



The Display Properties window allows you to adjust more precisely the relative positioning of the two displays when they are configured as an extended desktop. On the Display Properties window, the two displays can be positioned horizontally, vertically or in any diagonal configuration you wish, as shown below.

If an external display will not be connected next time you use your computer, you should cancel any extended desktop or clone display settings before shutting down your computer.


User's Manual 5-5



Playing DVDs

The WinDVD software for playing DVD movie titles is already installed. To use it, simply insert the DVD disc into the disc tray. Your computer will launch the WinDVD software automatically.

Using a CD-RW, DVD-R/-RW or DVD Multi Drive If your computer comes with either the CD-RW, DVD-R/-RW or DVD Multi Drive, you can write to either CD-R, CD-RW, or DVD-R media. For CD authoring, Drag ‘n Drop CD+DVD software comes preinstalled with the computer. For more on how to use it, please refer to the program’s online help file. For DVD authoring, there is a disc called Motion DV Studio. You have to install the software by yourself. First, insert the disc into the drive, then the setup dialog box shows up automatically. You can then follow the onscreen display step by step method to install it.

For more Information on using Drag’n Drop CD+DVD software, please consult the documentation that came with it.

When using the CD-RW, DVD-RW or DVD Multi drive device, do not copy data directly from an external device. (e.g. USB, i.LINK device). Please copy the data into the Hard Disk Drive, then copy to the disc.

About DVD-RAM The Multi-drive device supports the DVD-RAM (DVD Random Access Memory) media. This allows data to be written and rewritten on a disc up to 100,000 times. Data, including video and audio files, can be stored on a DVD-RAM disc and accessed just as with a hard drive using standard drag-and-drop techniques. Single-sided (4.7GB) and double-sided (9.4GB) media are available as bare discs or enclosed in cartridges.


User's Manual 5-6



Playing CDs, DVDs And Digital Music Files With The Computer On Or Off

You can listen to CDs with the computer turned off and also start playing digital music files and DVDs, in which case the computer will turn on automatically. Use the CD/Digital Mode button on the front of the computer to switch between CD mode and Digital mode.

Whether your computer is turned on or off, the CD/Digital control buttons are locked by default. To unlock them, press the CD/Digital mode button for more than 3 seconds. Press the mode button again for over 3 seconds to lock them again. When the computer is off and in CD or Digital mode, the buttons will lock automatically after 2 minutes if Play is not pressed and no CD is playing.

CD/DIGITAL MODE BUTTON PREVIOUS NEXT PLAY/PAUSE

CD MODE INDICATOR

LED DIGITAL MODE INDICATOR LED

STOP/EJECT

You can refer to chapter 1 for instruction on using the CD control buttons.

CD Mode Computer Power Off state: You can use the CD controls to play an audio CD without turning on the computer. Press the CD/Digital Mode button for more than 3 seconds until the Direct CD LED lights, then press play. If there is no response, press Stop/Eject and check to make sure a CD is correctly placed in the CD tray. If a DVD is in the drive, pressing play will turn the computer on in order to start playing the DVD title (as long as your computer is equipped with a DVD drive). Computer Power On state: Press the CD/Digital Mode button for more than 3 seconds until the Direct CD LED lights. Pressing play will launch the media application appropriate for either a CD or DVD. If the CD tray is empty, an alert window will inform you.


User's Manual 5-7



Digital Mode In Digital mode, your computer can play DVD video, MP3s, Wav files, Midi files, and other forms of digital music file. When the CD control buttons are unlocked (by pressing the CD/Digital Mode button for over three seconds) the computer initially enters the CD mode. Switch to Digital Mode by pressing the Mode button again briefly. Computer Power Off state: If you push the play button while the computer is off and in Digital Mode, the computer will power on, launch Microsoft Windows Media Player and play by default from the digital playlist. Computer Power On state: If you push the play button while the computer is on and in Digital Mode, Microsoft Windows Media Player will launch and start playing by default from the digital playlist.

Using The FIR Port

You can transfer files to another computer using your Satellite notebook computer’s FIR (Fast Infrared port). Both computers involved in the data transfer must have compatible infrared ports and synchronization software. Your computer may not have this function, depending on the model bought.

FIR PORT


User's Manual 5-8



Using The TOSHIBA Remote Control

You can control your Windows® software, digital media files and files on CDs or DVDs with the remote control device that ships with your computer. Not all models will come with a TOSHIBA Remote Control. The receiver port on the front of your computer should not be blocked or covered for it to work. To use, simply point the controller towards the computer’s front panel and press the appropriate button.

Not all models ship with the TOSHIBA Remote Control

The remote control’s features are:

Power On/Off Turns the computer on and off.

TV Out Changes display to an external TV.

Maximize/Restore Maximize the active window, or restores it to its original size

Switch Window Cycles through any open windows.

Volume Up/Down Turns the volume up or down.

Volume Off Turns the volume all the way down.

Pressing the button a second time restores the volume to its last level.

Pointer Controls These five buttons control the pointer’s position on screen. The button in the centre is the ‘Enter’ button.


User's Manual 5-9



Tab Key Identical to the keyboard’s tab key.

Menu Calls up the DVD menu during DVD playback.

Mode Switches modes.

Play/Pause Plays and/or pauses the current track, whether it

is a DVD or CD.

Stop Stops playing.

Previous Skips to the previous chapter/track.

Fast Backward Shuttles backwards through the track.

Fast Forward Shuttles forwards through the track.

Next Skips to the next chapter/track.

Using Wireless LAN

Your computer may integrate 802.11b or 802.11a/b Wireless Networking, depending on the model purchased. It is a high- speed wireless network connection that uses two-way radio transmission to communicate with an “Access Point” transceiver that is physically connected to the network by cable. The Atheros Client Utility, which is the Wireless Networking driver utility, has been pre-installed and setup on the computer. You may get detailed operating and setup information from its online Help.

This utility should be used only if you have an 802.11a/b setup, but not for 802.11b. If you are using 802.11.b, use the manager built into Windows® XP. Adhoc mode is only supported on 802.11b.

1. Slide the Wireless Communication switch to turn on the Wireless Networking. The LED will light amber to show the on status.

2. Run the TOSHIBA Client Manager from the system task bar to connect the nearest Access Point if you are using 802.11a/b.

With the Wireless Communication switch in the ‘on’ position, Wireless LAN activity can be turned on and off at any time by pressing the hot key Fn + F8.

Please turn off wireless networking feature before boarding a plane or entering a hospital.


User's Manual 5-10



Using The TOSHIBA Power Management Utility

The TOSHIBA Power Management Utility is pre-installed in your computer. This software allows you to select the power scheme with the most appropriate settings for this computer. You can double click the TOSHIBA Power Management Utility icon on the system taskbar to execute the program. Following the on-screen display step by step panels, you will find following settings. 1. Battery Mode: Lets you select either Long Life, Normal, High Power or

DVD Playback power schemes. For each individual setting, you can adjust Monitor Brightness, Turn Off Monitor, Turn Off Hard Disks, System Stand By, and System Hibernate at different battery power capacity.

2. AC Mode: There is one Power Scheme, which is Full Power. As with the various battery modes, you can adjust the specifics for Full Power management.

3. Alarm: You can adjust the Low Battery Alarm and Critical Battery Alarm when the Battery Power reaches a certain level. The Alarm Action be either sound Alarm or Display message or both.

4. Advanced: Lets you can select the power saving settings you want to use. You can select the power button and lid switch function here. You can also select the cooling method you want to use.

5. Battery Power Meter: Displays the current the power source and Battery Power capacity. You can see the current battery capacity on the edge of right side of the on-screen display. After finishing your settings, you should click OK to confirm or cancel to ignore the new settings.

Expanding & Upgrading

User's Manual 6-1



Chapter 6


This chapter covers things you can do to expand and upgrade your computer including connecting external peripherals, buying additional disk drives to attach externally and installing more system memory.

Using External Peripherals

Your computer is ideally suited for use as a desktop computer in the office or at home. If you frequently use your computer at one location, you might want to connect a number of peripheral devices, such as a full-size keyboard, speakers, a larger display device or speakers, to boost your computer’s capabilities and make it more comfortable to use. In this section we’ll look at how to attach the most common devices.

Satellite P20

User's Manual 6-1


User's Manual 6-2



Connecting A USB Keyboard

You can install a full-size USB keyboard. This may be more convenient for some tasks and saves wear and tear on the computer’s built-in keyboard.


To install an external USB keyboard do as follows: 1. Plug the keyboard into one of the USB ports on the computer. We

recommend that right-handed users connect the keyboard to one of the rear ports, keeping the port on the right side of the computer free for an external pointing device. Left-handed users may find it more convenient to reverse that arrangement.

2. If the keyboard has advanced features that require a driver or other software, install it according to the instructions that come with it.

3. Position the keyboard where you want to use it.



User's Manual 6-3



Connecting An External USB Pointing Device

You can install an external USB pointing device, such as a mouse, to use instead of, or in addition to, the built-in Touch pad device. You can use any type of pointing device as long as it has a USB interface.


To install an external USB pointing device do as follows: 1. Plug the device into one of the USB ports on the computer. We

recommend right-handed users attach the device to the USB port on the right-hand side of the computer; left-handed users may find it more convenient to use one of the USB ports on the rear.

2. The device may require a driver and possibly other software. Install it according to the instructions that come with it.

3. Position the device where you want to use it.



User's Manual 6-4



Connecting An External Monitor

You might want to connect an external monitor to your computer to have a larger screen and to reduce wear on the built-in LCD screen. You can connect a CRT desktop monitor to the standard 15-pin external monitor port on the rear of the computer, or, if the monitor has a USB interface, to one of the USB ports.

EXTERNAL MONITOR

PORT

To connect a monitor to the external monitor port do as follows:

Make sure the computer is turned off before connecting an external monitor.

1. Turn off the computer. 2. Check the instructions that come with the monitor. 3. Plug the 15-pin VGA connector from the monitor onto the external

monitor port of the computer. 4. Tighten the screws on the connector to secure the connector to the

monitor. If the monitor supports “Plug and Play” as most newer monitors do, Microsoft® Windows® operating system will automatically recognize and configure the system for it. You can then use the Display Properties control panel to configure display settings for the monitor. See chapter 5 for details.


User's Manual 6-5



Connecting A Television

You might want to connect a television to your computer to have a larger screen to watch DVDs. You can connect a television by using an S-video cable in the TV Out port on the right side of the computer.

TV OUT PORT

To connect a television to the TV Out port do as follows:

Make sure the computer is turned off before connecting an external television.

1. Turn off the computer. 2. Check the instructions that come with the television. 3. Plug the connector from the television onto the TV Out port of the

computer. You can use the Display Properties control panel to configure display settings for the television. See chapter 5 for details.


User's Manual 6-6



Connecting Audio Devices

The audio jacks on the left side of the computer allow you to connect several devices including speakers and a microphone.

Connecting external speakers You can connect self-powered stereo speakers to the computer to provide better sound reproduction than that from the built-in speakers and save wear on them.

HEADPHONE JACK

To connect self-powered external speakers do as follows: 1. Position the speakers where you want them. 2. Plug the mini-plug connector from the speakers into the Headphone

Jack on the left side of the computer. 3. Plug the speakers into a power source. 4. Turn on the computer and adjust the volume from the volume control

in the taskbar system tray. You may want to play something to check the volume level.

The internal speakers are disabled when you connect external speakers to the Headphone Jack.


User's Manual 6-7



Connecting A Microphone

If you want to use a microphone for recording, voice commands or computer telephony, you can connect one to the microphone jack.

LINE-IN JACK MICROPHONE JACK

To connect a microphone, do as follows: 1. Make sure the microphone you get is a standard computer

microphone with a 3.5mm mini-plug connector. 2. Plug the microphone into the microphone jack on the computer. 3. Adjust the microphone volume in the Windows Sounds and Audio

Devices control panel's Audio panel section by clicking on the Volume button of Sound playback and Sound Recording.

Connecting A Line-In

The line-in jack lets you connect a digital audio line to your computer, such as from a midi player. 1. Make sure the line-in cable you get is a standard Audio cable with a

mini-plug connector. 2. Plug the line-in cable into the line-in jack on the computer.


User's Manual 6-8



Additional Options

You can add new modules either externally, via the USB ports, or, by means of the Main or 2nd Module Bay.

External floppy disk drive You can purchase a TOSHIBA external USB floppy disk drive. The drive is powered from the computer. You simply plug it in and it works.


Alternatively, you can purchase a TOSHIBA FDD module, which can be inserted in the Main or 2nd Module Bay.

Module Bay Options A FDD Module (floppy disk drive) or a second hard disc drive (HDD) can be used in place of an Optical Media Drive (such as DVD-R/-RW). The FDD goes into the Main Module Bay. The Windows® Operating System automatically detects it, listing it in Explorer. Alternatively, you can install a second Optical Media Drive in the 2nd Module Bay, replacing the battery that normally goes there. The Windows® Operating System automatically detects it, listing it in Explorer below the one you already have.


User's Manual 6-9



Upgrading System Memory

You can upgrade the system memory in your computer. The computer has two sockets for DDR SODIMM memory modules. They are located in the memory compartment on the underside of the computer. Generally, at least one socket has a module installed when you get the computer and the other socket is empty to allow for upgrades, but depending on your configuration you may actually have both sockets occupied with memory modules. The computer can have a maximum of 2 GB installed. This means it can take two 1 GB memory modules. If you want to upgrade the system memory, you should use only certified modules. Ask your vendor or check the TOSHIBA web site for a list of approved memory products. The basic specifications of the memory used are: ■ DDR 266/333 specification compliant ■ 128MB, 256MB, 512MB or 1GB capacity

Installing additional memory Unless you are familiar with computer upgrades and comfortable doing so, we suggest that you have any memory upgrades installed at the nearest TOSHIBA Service Centre. If you want to install a memory upgrade yourself, do as follows: 1. Make sure the computer is turned off, with AC adapter disconnected

and battery removed.

Never add or remove memory modules with the computer on or in Standby or Hibernation. Ensure the system is turned off, the AC adapter is not connected and the battery has been removed.


User's Manual 6-10



2. Place the computer on a static-free surface and turn it over. 3. Remove the memory module cover by removing the two retaining

screws and lifting the cover panel out.

MEMORY MODULE

COVER

4. Insert the SO-DIMM module in the socket at about a 45º angle and then press it down into the socket until it snaps in place.


User's Manual 6-11



5. Restore the memory module cover back to its place and secure it with the two retaining screws.

The memory upgrade is now installed. Turn the computer right side up, open it and turn it on. The system should automatically recognize the new total memory capacity. You can check this by clicking on My Computer with the right Mouse button, clicking on the Properties item in the menu that appears and display the memory size in the General panel of the System Properties control panel.

If you install a memory module that is not compatible with the computer, a beep will sound and the LCD screen will be blank when you turn on the power. In this case shut down the power and remove the incompatible memory module.

If Something Goes Wrong

User's Manual 7-1



Chapter 7


Some problems you may encounter when using the Satellite P20 computer are relatively easy to identify and solve. Others may require help from your dealer or the manufacturer of a software program. This chapter aims to help you solve many problems by yourself without additional help. It covers the problems you are most likely to encounter. If all else fails, contact nearest TOSHIBA dealer or service support. You will find information on TOSHIBA’s support services in Appendix E.

Problems That Are Easy To Fix

Your program stops responding If you are working with a program that suddenly freezes all operations, or the execution program has stopped responding, you can exit the failed program without shutting down the Microsoft® Windows® operating system or closing other programs. To close a program that has stopped responding: 1. Press Ctrl, Alt, and Del simultaneously (once).

The operating system displays the Windows Task Manager box. This lists all the programs and processes currently in operation. Select the Applications tab. If a program has stopped responding, the words “not responding” appear beside its name in the list.

2. Select the program you want to close then click End Task. Closing the failed program should allow you to continue working. If it does not, continue with step 3.

3. Close the remaining programs one by one by selecting the program name and clicking End Task.

4. Click on the Shut Down drop-down menu of the Windows Task Manager box and select Restart.

Your computer shuts down and restarts, thus restoring operations.

Pressing Ctrl, Alt, and Del simultaneously twice to restart your computer is not recommended. By closing all open programs prior to shutting down Microsoft® Windows® operating system you ensure that all data is saved.

Satellite P20

User's Manual 7-1


User's Manual 7-2



Your program performs an illegal operation If you receive the message, “Your program has performed an illegal operation,” you should record the details of the message and consult the software manufacturer. To record the details: 1. Click the Details button and select the text, Microsoft® Windows®

operating system displays. The Details button displays information that the software manufacturer needs to help you solve your problem.

2. Press Ctrl and c simultaneously to copy the text to the clipboard. 3. Open Notepad (click Start, point to All Programs, then point to

Accessories and click Notepad). 4. Press Ctrl and v simultaneously to paste the details into Notepad. 5. Add a paragraph break and type some notes describing what you

were doing when you received the message. 6. Save the file and refer to it when you contact the software

manufacturer.

Hyper Threading Technology Incompatibility Some applications may not be compatible with Hyper Threading Technology (HTT). If an application does not work with HTT, try disabling it as described below. 1. Turn the computer on. 2. Press F2 key to enter BIOS setup menu when TOSHIBA logo appears

on the screen. 3. Set [Disable] in [Advanced]->[Hyper Threading Technology] 4. Reboot the computer.

Windows2000 does not support HTT. HTT should be disabled if Windows2000 is installed before Windows2000 setup. Not all of models come with HTT.

Problems When You Turn On The Computer

These problems may occur when you turn on the power.

The computer will not start Make sure you attached the AC adapter and power cable properly or installed a charged battery. Press and hold down the power button for a few seconds.


User's Manual 7-3



The computer is not accessing the hard disk or the diskette drive Your computer normally loads Windows from the hard disk. If you have a hard disk problem, you will not be able to start the computer. Insert a system diskette into the diskette drive, then press the power button.

Power problems The computer displays the Non-system disk or disk error message. Make sure there is no diskette in the diskette drive. If there is one, remove it and press any key to continue. If pressing any key does not work press Ctrl, Alt, and Del and select Shut Down and then Restart or turn off the computer by holding down the power button for several seconds.

Fixing Device-Related Problems

If you do not have a hardware conflict, but you think your problem could be related to one of your computer’s devices, you can use: ■ Dr. Watson - A diagnostic tool that takes a snapshot of your system

whenever a system fault occurs. To open Dr. Watson click Start, and then click Run. In the Open box, type drwtsn32.

■ System Information - Collects your system configuration information and provides a menu for displaying the associated system topics. To open System Information click Start, and then click Run. In the Open box, type msinfo32.

Refer to your operating system documentation for more information on using these tools. After diagnosing the problem, read the part of this section that describes problems and solutions related to specific devices.

Memory module problems

Incorrectly connected or faulty memory modules may cause errors that seem to be device-related. So it is worthwhile checking for these first: 1. Click Start, then click Turn Off Computer. 2. Select Turn Off.

Microsoft® Windows® operating system shuts down and turns off the computer automatically.

3. Remove the memory module(s). 4. Reinstall the memory module(s), following the instructions in Chapter 6

and making sure they are seated properly in the module sockets. 5. Check for the error again. 6. If the error recurs, remove the memory module entirely and check for

the error again using the second or another module. If removing the memory module eliminates the error, the module may be faulty. If the error occurs without the module installed, the module is not causing the error.


User's Manual 7-4



Power Problems

Your computer receives power from the battery which is charged through the AC adapter. Power problems are interrelated. For example, a faulty AC adapter or power cable will neither power the computer nor recharge the battery. Here are some typical problems and how to solve them:

The DC-IN LED does not come on when you plug in the AC adapter and power cable Make sure the AC adapter and attached power cable are plugged into both a working wall outlet and the computer. If the DC-IN LED still does not come on, check that the wall outlet is working properly by plugging in a lamp or other appliance.

The AC adapter and power cable work correctly, but the battery will not charge The battery doesn’t charge while the computer is consuming full power. Try turning off the computer or shutting down applications such as the DVD player that use a lot of power. The battery may not be inserted correctly in the computer. Turn off the computer, remove the battery, clean the contacts with a soft dry cloth (if necessary) and replace the battery. The battery may be too hot or too cold to charge properly. If you think this is the probable cause, let the battery reach room temperature and try again. If the battery has completely discharged, it will not begin charging immediately. Leave the AC adapter and power cable connected, wait 20 minutes and see whether the battery is charging. If the battery light is glowing after 20 minutes, let the computer continue charging the battery for at least another 20 minutes before you turn on the computer. If the battery light does not glow after 20 minutes, the battery may have reached the end of its useful life. Try replacing it.

The battery appears not to power the computer for as long as it usually does Check the power options using the TOSHIBA Power Management utility. Have you added a device, such as a PC Card or memory module, that takes its power from the battery? Is your software using the hard disk more? Is the display power set to turn off automatically? Was the battery fully charged to begin with? All these conditions affect how long the charge lasts. For more information on maximizing battery power, see “Maximizing Battery Life” in chapter 4.


User's Manual 7-5



Keyboard Problems

If, when you type, strange things happen or nothing happens, the problem may be related to the keyboard itself.

The keyboard produces unexpected characters A keypad overlay may be on. If the numeric keypad or cursor control light is on, press Fn and F10 simultaneously to turn off the cursor control light or press Fn and F11 simultaneously to turn off the numeric keypad light. If the problem occurs when both the keypad overlays are off, make sure the software you are using is not remaking the keyboard. Refer to the software’s documentation and check that the program does not assign different meanings to any of the keys.

You have connected an external keyboard and the operating system displays keyboard error messages If you have a second keyboard, try it. If it works, the first keyboard may be defective or incompatible with your computer.

Nothing happens when you press the keys on the external keyboard If you plugged the external USB keyboard in while the computer was turned on, your computer may have failed to recognize it. Using the Touch pad or pointing device to click Start, then click Turn Off Computer. When Microsoft® Windows® operating system displays the Turn Off Computer dialog box, select Restart and click OK. The computer will restart and recognize the device.

The keyboard locks and the computer will not restart Push the power button for more then 4 seconds. The computer will turn off. Then push the power button again to turn on the computer.

Restarting the computer in this manner may cause irreparable loss of data. It is not recommended you do this unless absolutely warranted.


User's Manual 7-6



Display Problems

Here are some typical display problems and their solutions:

The display is blank Display Auto Off may have gone into effect. Press any key to activate the screen. You may have activated the instant security feature by pressing Fn and F1 simultaneously. If you have registered a password, type it and press any key. If no password is registered, simply press any key. The screen reactivates and allows you to continue working. If you are using the built-in screen, make sure the display priority is not set for an external monitor. To do this, press Fn and F5 simultaneously (once). If this does not correct the problem, press Fn and F5 simultaneously again to return the display priority to its previous setting. If you are using an external monitor or television: ■ Check that the monitor or television is turned on. ■ Check that the monitor or television’s power cable is firmly plugged

into a working power outlet. ■ Check that the cable connecting the external monitor or television to

the computer is firmly attached. ■ Try adjusting the contrast and brightness controls on the external

monitor or television. ■ Press Fn and F5 simultaneously to make sure the display priority is

not set for the built-in screen. ■ If no image appears on the screen after switching displays, press

Fn + Spacebar simultaneously to change the resolution.

The screen does not look right You can change the display settings by clicking a blank area of the desktop with the Touch pad secondary button, then clicking Properties. This causes operating system to open the Display Properties dialog box. The Appearance tab of this dialog box allows you to choose the colours for the screen. The Settings tab allows you to choose the screen resolution.

The built-in screen flickers Some flickering is a normal result of the way the screen produces colours. To reduce the amount of flickering, try using fewer colours. To change the number of colours displayed: 1. Point at the desktop and click with the secondary button. 2. Click Properties, and then Settings. 3. Change the Colour quality option and click OK. For more information, see Windows Help.


User's Manual 7-7



A message indicates a problem with your display settings and that the adapter type is incorrect or the current settings do not work with your hardware Reduce the size of the colour palette to one that is supported by the computer’s internal display. To change the display properties: 1. Point at the desktop and click with the secondary button. 2. Click Properties, and then Settings. 3. Change settings and click OK. For more information, see Windows Help.

Disk Drive Problems

Problems with the hard disk or with a diskette drive usually show up as an inability to access the disk or as sector errors. Sometimes a disk problem may cause one or more files to appear to have garbage in them. Typical disk problems are:

You are having trouble accessing a disk, or one or more files appear to be missing Make sure you are identifying the drive by its correct name (A: or C:). Run Error-checking to check for file system errors and bad sectors on your hard disk. To run Error-checking: 1. Click Start and open My Computer. 2. Click the drive you want to test. 3. On the File menu, click Properties. 4. On the Tools tab, under Error-checking, click Check Now. 5. Under Check disk options, select the Scan for and attempt

recovery of bad sectors check box. All files must be closed for this process to run. If the drive is currently in use, a message box will appear prompting you to indicate whether or not you want to reschedule the disk checking for the next time you restart your system. Then, the next time you restart your system, disk checking will run. Your drive will not be available to perform other tasks while this process is running.

Your hard disk seems very slow If you have been using your computer for some time, your files may have become fragmented. Run Disk Defragmenter. To do this, click Start, point to All Programs, Accessories, System Tools, and click Disk Defragmenter.


User's Manual 7-8



Your data files are damaged or corrupted Refer to your software documentation for file recovery procedures. Many software packages automatically create backup files. You may also be able to recover lost data using utility software, which is available from your dealer.

Some programs run correctly but others do not This may be a software configuration problem. If a program does not run properly, review the program’s hardware configuration requirements. Most software documentation lists the minimum hardware requirements. See “Features and Specifications” (appendix B) to review the hardware configuration of this computer.

A disk will not go into the diskette drive You may already have a diskette in the drive. Make sure the drive is empty. You may be inserting the diskette incorrectly. Hold the label of the disk with the hub side facing down, and insert it so that the metal head window cover goes into the drive first. The metal cover or a loose label may be obstructing the path into the drive. Carefully inspect the diskette. If the metal cover is loose, replace the diskette. If the label is loose, replace the label and try inserting the diskette again.

The computer displays the Non-system disk or disk error message If you are starting the computer from the hard disk make sure there is no diskette in the diskette drive. If you are starting the computer from a diskette, the diskette in the drive does not have the files necessary to start the computer. Replace it with a bootable diskette.

The drive can not read a diskette Try another diskette. If you can access the second diskette, the first diskette (not the diskette drive) is probably causing the problem. Run the Check Disk tool on the faulty diskette (for instructions, see “Disk drive problems” earlier in this section).


User's Manual 7-9



CD-ROM Drive Problems

You cannot access a CD in the drive Make sure the CD-ROM tray has closed properly. Press gently until it clicks into place. Open the CD-ROM tray and remove the CD. Make sure the CD-ROM tray is clean. Any dirt or foreign object can interfere with the laser beam. Examine the CD to see whether it is dirty. If necessary, wipe it with a soft clean cloth dipped in water or a neutral cleaner. Replace the CD in the drawer. Make sure it is laying flat, label side uppermost. Press down until the CD-ROM disc locks on the spindle. Close the CD-ROM tray carefully, making sure it has shut completely.

You press the CD-ROM eject button, but the CD-ROM tray does not slide out Make sure the computer is connected to a power source and turned on. The CD-ROM drive eject mechanism requires power to operate. If you need to remove a CD and cannot turn on the computer, use a narrow object, such as a straightened paper clip, to press the manual eject button. This button is in the small hole next to the CD-ROM eject button on the right side of the computer.

Some CDs run correctly, but others do not If the problem is with a data CD, refer to the software’s documentation and check that the hardware configuration meets the program’s needs. The colour of the materials used to make the CD can affect its reliability. Silver-collared CDs are the most reliable, followed by gold-coloured CDs. Green-coloured CDs are the least reliable.

Sound System Problems

You do not hear any sound from the computer Adjust the volume control. If you are using an external headphone or speakers, check that they are securely connected to your computer.

The computer emits a loud, high-pitched noise This is feedback between the microphone and the speakers. It occurs in any sound system when input from a microphone is fed to the speakers and the speaker volume is too loud. Adjust the volume control.


User's Manual 7-10



PC Card Problems

PC Cards (PCMCIA-compatible) include many types of devices, such as a removable hard disk, additional memory, fax/modem, or pager. Most PC Card problems occur during installation and setup of new cards. If you’re having trouble getting one or more of these devices to work together, several sections in this chapter may apply. ■ Resource conflicts can cause problems when using PC Cards. ■ If the device is a modem, see “Modem problems” later in this chapter.

PC Card Checklist ■ Make sure the card is inserted properly into the slot. ■ Make sure all cables are securely connected. ■ Make sure the computer is loading only one version of Card and

Socket Services. ■ Occasionally a defective PC Card slips through quality control. If

another PCMCIA-equipped computer is available, try the card in that machine. If the card malfunctions again, it may be defective.

Resolving PC Card Problems

Here are some common problems and their solutions:

The slots appear to be dead and PC Cards that used to work no longer do Check the PC Card status: 1. Click the My Computer icon with the secondary button, then click


2. Click the Hardware Tab, then the Device Manager button. 3. Double-click the device listed as your PC Card. Windows® operating system displays your PC Card’s Properties dialog box. This dialog box contains information about your PC Card configuration and status.

The computer stops working when you insert a PC Card The problem may be caused by an I/O (input/output) conflict between the PCMCIA socket and another device in the system. Use Device Manager to make sure each device has its own I/O base address. Since all PC Cards share the same socket, each card is not required to have its own address.


User's Manual 7-11



Hot swapping (removing one PC Card and inserting another without turning the computer off) fails Follow this procedure before you remove a PC Card: 1. Click the PC Card icon on the taskbar. 2. Click Safely remove xxxx, where xxxx is the identifier for your PC

Card. Windows® operating system displays a message that you may safely remove the card.

3. Remove the card from the slot.

The system does not recognize your PC Card or PCMCIA socket controller This problem may be caused by a low battery. Replace the battery with a fully-charged one or charge the battery fully as follows: 1. Make sure the computer is not in Standby. 2. Turn off the computer. 3. Connect the AC adapter and power cable. 4. Keep the computer plugged in for about four hours with the power

turned off. If power is not the problem, try removing the card, inserting it again, and reinstalling it using the procedure in “Inserting PC Cards” in chapter 3. The problem may also be caused by a conflict with any additional memory in your system. If you recently installed a memory expansion card, turn off the computer, remove the memory, turn on the computer and try the PC Card again.

A PC Card error occurs Reinsert the card to make sure it is properly connected. If the card is attached to an external device, check that the connection is secure. Refer to the card’s documentation, which should contain a troubleshooting section.


User's Manual 7-12



Printer Problems

This section lists some of the most common printer problems.

The printer will not print Check that the printer is connected to a working power outlet, turned on and ready (on line). Make sure the printer cable is firmly attached to the computer and the printer. If your printer is ECP- or IEEE 1284-compliant, make sure you have an IEEE 1284 printer cable. Check that the printer has plenty of paper. Some printers will not start printing when there are just two or three sheets of paper left in the tray. Run the printer’s self-test to check for any problem with the printer itself. Make sure you installed the proper printer driver. Try printing another file. For example, you could create and attempt to print a short test file using Notepad. If a Notepad file prints correctly, the problem may be in your original file. Contact your network administrator if the printer is on your network.

The printer will not print what you see on the screen Many programs display information on the screen differently from the way they print it. See if your program has a print preview mode. This mode lets you see your work exactly as it will print. Contact the software manufacturer for more information.


User's Manual 7-13



Modem Problems

This section lists common modem problems.

The modem will not receive or transmit properly Make sure the RJ-11 cable (the one that goes from the modem to the telephone line) is firmly connected to the modem’s RJ-11 jack and the telephone line socket. Check the serial port settings to make sure the hardware and software are referring to the same COM port. Check the communications parameters (band rate, parity, data length and stop bits) specified in the communications program. It should be set up to transmit at 300, 1200, 2400, 4800, 9600, 14400, 28800, 33600, 56000 bps (bits per second) or higher. Refer to the program’s documentation for information on how to change these settings. To check the modem’s settings and communications parameters: 1. Click the My Computer icon with the secondary button, then click


2. Click the Hardware Tab, then the Device Manager button. 3. Click on the modem name listed under Modems. Windows® operating system displays your modem’s Properties dialog box. This dialog box contains information about your modem configuration and status.

The modem is on, set up properly and still does not transmit or receive data Make sure the line has a dial tone. Connect a telephone handset to the line to check this. The other system may be busy or offline. Try making a test transmission to someone else.


User's Manual 7-14



Develop Good Computing Habits

■ Make sure you are prepared. ■ Save your work frequently. You can never predict when your computer will lock forcing you to close a program and lose unsaved changes. Many software programs build in an automatic backup, but you should not rely solely on this feature. Save your work! ■ On a regular basis, back up the information stored on your hard disk. Here are two ways you can do this: ■ Copy files to diskette in Microsoft® Windows® operating system. ■ Connect a backup device ( e.g. CD-R) to the system and use

specialized software to copy everything on the hard disk to a backup device.

Some people use a combination of these methods, backing up all files to backup device weekly and copying critical files to diskette on a daily basis. If you have installed your own programs, you should back up your programs as well as your data files. If something goes wrong that requires you to format your hard disk and start again, reloading all your programs and data files from a backup will save time. ■ Please check every three months to make sure the fan inlet is

unobstructed and clean the inlet if necessary. ■ Read the user’s guide. It’s very difficult to provide a fail-safe set of steps you can follow every time you experience a problem with the computer. Your ability to solve problems will improve as you learn about how the computer and its software work together. Get familiar with all the user’s guide provided with your computer, as well as the manuals that come with the programs and devices you purchase. Your local computer store or book store sells a variety of self- help books you can use to supplement the information in the manuals. ■ If problem-solving is taking a long time, take a break. If you have been fighting to solve a problem for a long time, you are probably frustrated by now. Stand up and take a deep breath. Often, you can find a new solution to a problem just by stepping away from it for a few moments.


User's Manual 7-15



If You Need Further Assistance

If you have followed the recommendations in this chapter and are still having problems, you may need additional technical assistance. This section contains the steps to take to ask for help.

Before you call Since some problems may be related to the operating system or the program you are using, it is important to investigate other sources of assistance first. Try the following before contacting TOSHIBA: ■ Review the troubleshooting information in your Microsoft® Windows®

documentation. ■ If the problem occurs while you are running a program, consult the

program’s documentation for troubleshooting suggestions. Contact the software company’s technical support group for their assistance.

■ Consult the dealer from whom you purchased your computer and/or program. Your dealer is your best source for current information.

Contacting TOSHIBA If you still need help and suspect that the problem is hardware related, TOSHIBA offers a variety of resources to help you. Please refer to appendix E for TOSHIBA support information.

Hot Keys

User's Manual A-1



Appendix A

Hot Keys

Hot keys are keys that, when pressed in combination with the Fn key, turn system functions on and off. Hot keys have an icon label on the key indicating the option or feature the key controls.

Volume mute Turns the volume off and on. When you press

these keys, the current setting is shown in a window.

Instant security Blanks the screen to prevent others from

accessing your data. To restore the screen and original settings, press any key or use the Touch pad. If you have set a screen saver password, a dialog box appears. Enter the password and click OK. If no screen saver password is set, the screen is restored when you press any key or use the Touch pad.

Power save mode Changes the power save mode. Press Fn+F2

once to display the Power Save Mode in a window. Press the hotkeys again to change the setting. You can also change this setting through the AC Power or Battery Power items of the Power Save Modes tab in the TOSHIBA Power Management Utility.

Standby The computer enters Standby. To avoid entering

Standby unexpectedly, a dialog box appears for verification. However, if you uncheck the dialog box, it will not appear the next time.

Hibernate The computer enters Hibernate. To avoid

entering Hibernate unexpectedly, a dialog box appears for verification. However, if you activate the checkbox in the dialog box, it will not appear the next time.

Display selection Changes the active display device. When you

press these hotkeys a dialog box appears. Only selectable devices are displayed.

Satellite P20

User's Manual A-1

Hot Keys

User's Manual A-2



Brightness down Decreases the display brightness. When you

press these hotkeys, the current setting is displayed for two seconds by a pop-up icon. You can also change these settings through the Monitor Brightness item of a specific item in the Power Save Modes tab of the TOSHIBA Power Management Utility.

Brightness up Increases the display brightness. When you

press these hotkeys, the current setting is displayed for two seconds by a pop-up icon. You can also change these settings through the Monitor Brightness item of a specific item in the Power Save Modes tab of the TOSHIBA Power Management Utility.

Wireless Device Controls

Functions only if the Wireless Communications Switch has been turned on. The Wireless Communication LED on the system indicator panel lets you know when the wireless devices are active. Pressing this key combination lets you select a device mode.

Touch pad Enables or disables the Touch pad function.

When you press these hotkeys, the current setting is changed and displayed as an icon.

Cursor keypad on/off Pressing this hot key can enable/ disable the

embedded cursor keypad. Numeric lock state is logically disabled. See chapter 3 for more on the embedded keypads.

Numeric keypad on/off

Pressing this hot key can enable/ disable the embedded numeric keypad. Numeric lock state is logically enabled. See chapter 3 for more on the embedded keypads.

Scroll lock on/off This hot key turns the scroll lock feature on and

off.

Change resolution Changes the current screen resolution.

The cursor and numeric keypads are set to off whenever you restart or turn your computer on. Brightness settings are likewise overridden during Start-up by those set in the Power Management Utility. For TOSHIBA Power Management Utility, refer to chapter 5.

Features And Specifications

User's Manual B-1



Appendix B


This appendix lists the features of the Satellite P20 series computers and summarizes their specifications.

CPU ■ 2,53 GHz Intel® Pentium® 4 processor 2,53 GHz ■ 2,66 Intel® Pentium® 4 processor 2,66 GHz

with 533 MHz system bus, or ■ 2,40C GHz / 2,60C GHz / 2,80C GHz / 3.0 GHz / 3.0C GHz

with 800 MHz system bus and Hyper-Threading Technology

Other processors may be introduced in the future.

Chip Set ■ Intel 865 PE ■ Intel 82801 EB I/O Controller HUB ■ PC87591L for Keyboard Controller, Battery Management Unit, and

RTC ■ T7L58XB for Card Bus PCMCIA controller and SD controller ■ nVIDIA GeForce FX Go5200 graphics controller ■ ALC202 for AC97 CODEC ■ OZ168 for Direct CD play controller ■ 8101L for LAN controller

Memory ■ On board with two 200-pin +2.5V SO-DIMM connector supporting

DDR memory cards. Maximum upgradable to 2 GB by two 1 GB SO-DIMM modules

■ 512 KB L2 Cache on CPU ■ External 32MB or 64MB VGA DDR RAM

Satellite P20

User's Manual B-1


User's Manual B-2



BIOS ■ 512KB Flash ROM for system BIOS ■ Password protection (System) ■ Windows XP ready with PnP ■ Suspend to RAM/Disk ■ Hot keys for system control ■ Refreshable ■ Complete ACPI 1.0b Function

Power ■ 12 cells Li-Ion 18650 size smart battery Pack with 14.8V x 6450 mAh

capacity ■ 12 hours or longer charge time to 100% capacity on Li-Ion Battery

when the system is on ■ Approximately 4 hours charge time to 100% capacity on Li-Ion

Battery when the system is off

One 2.5", 9.5mm Hard Disk, support with 30GB/40GB/60GB/80GB ■ Bus Master IDE ■ 9.5mm, 2.5” HDD Support ■ Support Ultra DMA100

Storage Devices (HDD/FDD/Optical disk drives) (depending on model) ■ 12.7mm, 1.44MB FDD device ■ 12.7mm height DVD-R/-RW device ■ 12.7mm height DVD-ROM device ■ 12.7mm height DVD Multi device ■ 12.7mm height CD-RW/DVD-ROM device ■ Second HDD Drive


User's Manual B-3



Options ■ PC2100 256MB / 512MB / 1GB DDR module ■ Module Bay HDD adaptor ■ HDD pack ■ CD-RW/DVD-ROM Drive Kit ■ DVD Multi Drive Kit ■ DVD-R/-RW Drive Kit ■ FDD Drive Kit ■ USB FDD Kit ■ Wireless LAN card (802.11b) ■ Wireless LAN card (802.11a/b) ■ AC Adaptor ■ Battery Pack ■ Bluetooth SD Card ■ Remote Control

Touch pad Point Device ■ Left Button ■ Right Button

I/O Ports (Depending on the model bought) ■ One 25-pin parallel port, EPP/ECP capability ■ One 15-pin external monitor port, supports DDC 2B ■ One TV-out port ■ One Microphone Jack ■ One Line-In Jack ■ One Headphone Jack ■ One DC-IN ■ One SD Card Slot ■ Four USB ports ■ One RJ11 jack ■ One RJ45 jack ■ VR for volume control ■ One FIR port ■ One Remote Control Receiver Port ■ One i.LINK (IEEE 1394) port


User's Manual B-4



PCMCIA Card ■ One type III card socket or two type II card sockets ■ MODEM/LAN card ■ ATA Card ■ Card bus card ■ ACPI 1.0b Compliant

Power Management Function ■ Standby mode, Suspend to RAM or Suspend to Disk mode, by time

out or by hot key ■ HDD Local Stand-By mode by time out ■ LCD Local Stand-By mode by time out ■ Low battery alarm by beep ■ Auto-backlight off when LCD cover closed ■ Full ACPI 1.0b supported ■ LCD Auto-DIM mode by time out

Switches ■ Power Button ■ One Internet Button ■ One TOSHIBA Console Button ■ One TV Out Button ■ CD/Digital Mode Button ■ Eject/Stop Button ■ Play/ Pause Button ■ Forward Button ■ Reverse Button

AC Adapter ■ Universal AC adapter module: 90-264V AC, 47-63HZ, 120W

Security ■ Boot-up password protection ■ Single level password architecture (Supervisor)

Power Cable Connectors

User's Manual C-1



Appendix C

Power Cable Connectors

The Satellite computer features a universal power supply you can use worldwide. This appendix shows the configuration of typical AC power cord plugs and sockets in various parts of the world.

USA and Canada United Kingdom

UL approved CSA approved

BS approved

Australia Europe

AS approved VDE approved/NEMKO approved

Satellite P20

User's Manual C-1

Display Modes

User's Manual D-1



Appendix D

Display Modes

This appendix is a table of the display mode options of your computer’s nVidia Graphics Controller when display device is set to an external monitor.

CRT Display Resolution

Colour Depth Refresh Rate (Hz)

800x600 16 32

60 70 72 75 85 60 70 72 75 85

1024x768 16 32

60 70 72 75 85 60 70 72 75 85

1280x1024 16 32

60 70 72 75 85 60 70 72 75 85

1400x1050 16 32

60 70 72 75 85 60 70 72 75 85

1600x1200 16 32

60 70 72 75 85 60 70 72 75 85

1920x1440 16bpp 32bpp

60 70 72 75 60

2048x1536 16bpp 32bpp

60 60

Satellite P20

User's Manual D-1

The TOSHIBA International Warranty

User's Manual E-1



Appendix E


The TOSHIBA International Warranty is a service policy on the parts and repair on your TOSHIBA portable personal computer which is automatically available to purchasers of the computer. The cover is assured in major industrial countries of the world. It means that wherever you take your TOSHIBA mobile PC in this area, you will never be left without help should any problems arise. For more information on the warranty coverage please refer to your warranty booklet supplied with your Notebook.

What the warranty covers The Warranty covers the computer in the standard version, including the AC adaptor. Batteries, modems, memory expansion kits and other TOSHIBA branded options, as well as third party expansion boards are NOT covered by this warranty. For information concerning warranties for these products, please consult your dealer.

If you would like to use the international warranty, please register for this warranty at the following Internet website: http://www.toshiba-europe.com/computers/warranty

Once your registration has been received by TOSHIBA the warranty entitlement of your Notebook can be checked on the following Internet website: http://gedb.toshiba.com On the following pages is a list of the TOSHIBA Authorised Service Providers who can be contacted if a claim on the warranty needs to be made. If users need further addresses in eastern Europe or outside Europe, these are available from the national or European companies. The countries to which the international warranty applies can be found using the TOSHIBA Global ASP locator. Click: Support, Find an Authorised Service Provider

Satellite P20

User's Manual E-1


User's Manual E-2



TOSHIBA's Worldwide Computer Representatives

Australia TOSHIBA (Australia) Pty. Limited 84-92 Talavera Road, North Ryde NSW 2113

Tel: +61-2-9887-3322 Fax: +61-2-9888-3664 http://www.isd.toshiba.com.au

Austria TOSHIBA Europe GmbH Leibnizstr. 2 93055 Regensburg

Tel: 0800-29 74 88 Fax:+49-(0)941-780 79 25 www.computer.toshiba.at

Azerbaijan AZEL (Azerbaijan Electronics) Floor 5, 65 Fizuli Str. 370014 Baku

Tel: +99412-974040 Fax: +99412-974042 http://www.azel.net

Belgium TOSHIBA Information Systems Belgium Excelsiorlaan 40 1930 Zaventem

Tel: +32-900-10990 Fax: +32-2-7253030 www.toshiba.be

Bulgaria IMPEX Sofia Ltd. 12, Anton Naydenov Street, PO Box 184, 1710 Sofia

Tel: +359-2-962-1219 Fax: +359-2-962-5062

Canada TOSHIBA of Canada Ltd. 191 McNabb Street Markham, Ontario L3R-8H2

Tel: +1-905-470-3500 Fax: +1-905-470-3487 http://www.toshiba.ca

Czech Republic

CHG Service , s.r.o. Videnska 102 619 00 Brno

Tel: +420-5-4742-6581 Fax: +420-5-4742-6590 http:// www.chgservice.cz

Denmark Scribona TOSHIBA Digital Media Hovedvejen 9 DK-2600 Glostrup

Tel: +45-3823-7600 Fax: +45-3823-7601 www.toshiba-dm.com

Egypt El Araby Co. for Trading and Manufactoring P.O. Box 1224/Off Beirut St. 10, Mohammed Sabry Abolaalm Street Kourba , Heliopolis / Cairo 11511

Tel: +202-291-6989 Fax: +202-291-6454 http://www.elaraby.com.eg

Estonia ServiceNet Pärnu str. 142 11317 Tallinn

Tel: +372-6504-949 Fax: +372-6504-948 http://www.servicenet.ee

Finland Scribona Suomi OY / TOSHIBA Digital Media Sinimäentie 8A,P.O.Box 83 02630 ESPOO

Tel: +358-9-5272555 Fax: +358-9-5272500 http://www.toshiba-dm.com

France TOSHIBA Systèmes (France) S.A. 7 Rue Ampère ; B.P. 131 92804 Puteaux Cedex

Tel.: +33-8 92 69 70 92 Fax: +33-1-4728-2247 http://www.pc.toshiba.fr

Germany TOSHIBA Europe GmbH Leibnizstraße 2 93055 Regensburg

Tel: 01805-23 16 32 Fax: +49-(0)941-7807-925 www.computer.toshiba.de

Greece Ideal Electronics S.A. 25 Kreontos Str. 10442 Sepolia, Athens

Tel: +30-210-5193950 Fax: +30-210-5193960 http://www.ideal.gr


User's Manual E-3



Hungary Technotrade Informatikai Rt. Öv u, 185, 1147 Budapest

Tel: +36-1-467 6100 Fax: +36-1-252 6470 http://www.technotrade.hu

Ireland TOSHIBA Information Systems (U.K.) Limited, TOSHIBA Court, Weybridge Business Park, Addlestone Road, Weybridge, Surrey KT15 2UL

Tel.: +353 (0)1248 1 248 Fax: + 44 (0)8702 202 303 www.toshiba.co.uk/computers/

Israel Mafil Technologies (3000) Ltd 8 Bareket Street 49517 Petah Tikwa

Tel: +972-3-918-3333 Fax: +972-3-924-1310 http://www.mafil.co.il

Italy Progetto Elettronica 92.S.p.A Via de Gasperi 88a 20017 Mazzo di Rho

Tel: +39-02-9397-5551 +39-02-939 75678 Fax: +39-02-9397-5299 http://www.pe92.it

Japan TOSHIBA Corporation, IOPC 1-1, Shibaura 1-Chome, Minato-KU Tokyo 105-01

Tel: +81-3-3457-5565 Fax: +81-3-5444-9262 http://www.toshiba.co.jp

Jordan Scientific & Medical Supplies Co. Jabal Amman, 1st Circle , Al Hayyek Street, Opposite to Housing Bank 11118 Amman

Tel: +962 (6) 4624907 Fax: +962 (6) 462858

Kuwait Arabian Business Machines Co. Salhiya-Sulaiman AL Laheeb Building 3 P.O. Box 29961, 13160 Safat

Tel: +965-242-9154 244-5373/-5369 Fax: +965-241-4399 www.abm-kuwait.com

Latvia Servicenet LV Bullu Str 9 LV1055 Riga

Tel: +371-7052079 Tel.: +371 7460399 Fax: + 371-7460299 http://www.servicenet.lv

Lebanon Pcdealnet Diab Bldg. Mkalles Rd., P.O. Box 11-316 Beirut

Tel: +961-1-682-956 Fax: +961-1-682-955 www.pcdealnet.com

Lithuania Servicenet LT verslo g. 6 Kumpiu km. Domeikava 4302 Kauno raj.

Tel: + 370 37 757586 Fax: + 370 37 757541 http://www.servicenet.lt

Luxemburg See 'Netherlands'

Malta Tabone Computer Centre Limited 111 Old Railway Track HMR-16 St Venera

Tel: +356-49 36 04 Fax: +356-49 36 03 http://www.tabone.com.mt

Morocco C.B.I. Lotissement Attoufik, Rue No 1 Immeuble 29, Sidi Maarouf 20190 Casablanca/ Maroc

Tel: +212- 22 43 71 60/61 Fax: +212-22 43 71 88

Netherlands TOSHIBA Information Systems Benelux B.V. Rivium Boulevard 41 2909 LK Capelle a/d IJssel

Tel: +31-0900-1000-1000 Fax: +31-10-2882-390 http://www.toshiba.nl


User's Manual E-4



Norway Scribona Norway A/S Stålfjæra 20, P.O.Box 51, Kalbakken 0901 Oslo

Tel: +47-22-897-189 Fax: +47-22-897-166 http://www.toshiba-dm.com

Oman (Sultanate of Oman)

Bahwan IT Sarco Building, Ground Floor No. 459, Way No. 3109 Al Noor Street, Ruwi 113 Muscat

Tel.: + 968 790191-117 Fax: +968-790 192 http://www.bahwanit.com

Poland AC Serwis Sp. Z o. o. ul. Przasnyska 6b, 01-756 Warszawa

Tel: +48- 22-56-08-205 Fax: +48- 22-56-08-20 http://www.acserwis.com.pl

Portugal TOSHIBA Information Systems Portugal Edificio D. Pedro I Quinta da Fonte 2780-730 Paço d’Arcos

Tel: +351-707265265 Fax: +351-21-000-1675 http://www.toshiba.pt

Qatar Mannai Trading Company Rayyan Road, P.O. Box 76 Doha

Tel: +974 441-2555 Fax: +974 444-5413

Qatar Jarir Bookstore Qatar Al Maha Center, Ramada Crossing, Salwa Road, P.O. Box 24824, Doha

Tel: +974 444 0212 Fax: +974 444 04 32 www.jarirbookstore.com

Romania Scop Computers SRL 162 Barbu Vacarescu St, Sector 2 71424 Bucharest

Tel: +40-1-231-4602 Fax: +40-1-231-4606 http://www.scop.ro

Russia AC SERSO Sovetskoi Armii st. 5 127018 Moscow

Tel: +7 - 095 284 5577 Tel: +7-095 105-8161 Fax: +7-095 284 5880 http://www.cepco.ru

Russia Microbit SERSO Izmailovskiy Pr.2 S.Petersburg 198005

Tel.: +7 812 327-5700 www.microbit.ru

Saudi Arabia Arabian Business Machines Co. Dareen Center, Ahsaa Road P.O. Box 2006 11451 Riyadh

Tel: +966-1 478 4909 Fax: +966-1 477 7803 www.olayangroup.com

Saudi Arabia Jarir Bookstore P.O. Box 3196 Olaya Street 11471 Riyadh

Tel: +966-1 462 6000 Fax: +966-1 462 9500 www.jarirbookstore.com

Slovakia HT Computers a.s. Dobrovicova 8 81109 Bratislava

Tel: +421-2-59334 550 Fax: +421-2-59334 555 http://www.htc.sk

Slovenia Inea d.o.o. Stegne 11, 1117 Ljubljana

Tel: +386-1-513-81-00 Fax: +386-1-513-81-70 http://www.inea.si


User's Manual E-5



South Africa CS IT Solutions, CS Holdings Office Park Block D, 241 Third Road PO Box 786691 1685 Midrand

Tel: +27 (0) 11 205-7000 Fax: +27-0-11-205-8586 http://www.cs.co.za/it.htm.

South Africa RECTRON (Pty) Ltd. 152 15th Road, Randjespark Midrand, 1685

Tel: +27-0-11-203-1000 Fax: +27-0-11-203-1100

Spain TOSHIBA Information Systems (España) S.A. Parque Empresarial San Fernando Edificio Europa, 1a Planta, Escalera A 28830 (Madrid) San Fernando de Henares

Tel: +34-91-6606-700 Fax: +34-91-6606-760 http://www.toshiba.es

Sweden TOSHIBA Digital Media Sundbybergsvägen 1, Box 1374 171 27 Solna

Tel: +46-200-212100 Fax: +46-8-734-4656 http://www.toshiba.se

Switzerland TOSHIBA Europe Gmbh, Swiss Sales branch, Chriesbaumstrasse 4 Postfach 171 CH-8604 Volketswil

Tel: +41-848-845250 Fax: +41-1-908 5658 http://www.toshiba.ch

Turkey Bekom Bilgisayar Sistemleri San. ve TIC. A.S. Burhaniye Mah. Neset Bey Sok. No:7 USKUDAR, ISTANBUL

Tel: +90 216 422 40 50 Fax: +90 216 422 55 20 http://www.toshibatr.com

Ukraine DKT-SERSO Lesya Ukrainka blv, 26 01133 Kiev

Tel: +380-44-573-9627 Fax: +380-44-254-4646 http://www.dkt-cepco.com.ua

United Arab Emirates

Al-Futtaim Electronics P.O. Box 5866, Bin Ham Building, Mezzanine Floor Adjacent to BurJuman Centre, Trade Centre Road, Dubai

Tel: +971 4 351 5004 Fax: +971 4 351 4254 http://www.toshibauae.com


Al-Futtaim Electronics, Central Services OperationGarhound Area, P.O. Box:531 Dubai, U.A.E.

Tel: +971 4 282 5112 Fax: +971 4 282 4094


Al-Futtaim Electronics, Central Services OperationMina-Area, P.O. Box:26605, Abudhabi, U.A.E.

Tel: +971 2 673 3004 Fax: +971 2 673 3809

United Kingdom

TOSHIBA Information Systems (UK) Ltd. TOSHIBA Court, Weybridge Business Park Addlestone Road, Weybridge Surrey KT15 2UL

Tel: +44-(0)8702 202202 Fax: + 44-(0)8702 202303 www.toshiba.co.uk/computers/

United States TOSHIBA America Information Systems, Inc. 9740 Irvine Blvd., P.O. Box 19724 Irvine, CA 92713-9724

Tel: +1-949-583-3000 Fax: +1-949-583-3345 http://www.toshiba.com

Yugoslavia CT Computers d.o.o. Vladimira Popovica 6 11070 Beograd

Tel: +381-11-311-2060 Fax: +381-11-311-2060 http://www.comtrade.co.yu


User's Manual E-6



TOSHIBA addresses for the Internet/World Wide Web

TOSHIBA Europe http://www.toshiba-europe.com

TOSHIBA Japan http://www.toshiba.co.jp

TOSHIBA America http://www.toshiba.com

TOSHIBA Canada http://www.toshiba.ca

If Your Computer Is Stolen

User's Manual F-1



Appendix F


Always take care of your computer and try to prevent it from being stolen. You are the owner of a valuable technical device, which may be highly attractive to thieves, so please do not leave it unattended in a public place. To further help protect against theft, security cables can be bought for use with your notebook when it is being used at home or in the office. Make a note of your computer’s machine type, model number, and serial number, and put it in a safe place. You will find this information on the underside of your notebook. Please also keep the receipt of the computer you purchased.

Should your computer be stolen, however, we’ll help you try to find it. Before contacting TOSHIBA, please prepare the following information which is necessary to uniquely identify your computer: ■ In which country was your computer stolen? ■ What type of machine do you have? ■ What was the model number (PA number)? ■ What was the serial number (8 digits)? ■ When was it stolen, i.e. date? ■ What was the warranty seal number (if available)? ■ What is your address, phone, and fax number?

To register the theft, please follow these procedures: ■ Fill in the TOSHIBA Theft Registration form (or a copy of it) below. ■ Attach a copy of your receipt showing where your computer was

purchased. ■ Either fax or send the receipt and registration form to the address

below. Your registration will be entered in a database, which is used to track TOSHIBA computers at our service points around Europe.

Satellite P20

User's Manual F-1


User's Manual F-2



TOSHIBA Theft Registration Send to: TOSHIBA Europe GmbH

Technical Service and Support Leibnizstr. 2 93055 Regensburg Germany

Fax number: +49 (0) 941 7807 925

Country stolen:

Machine type: (e.g. Satellite P20)

Model number: (e.g. PSA10 YXT)

Serial number: (e.g. 70123456E)

Date stolen:

Warranty seal: (e.g. 9813 123456 049)

Owner’s details

Name:

Company:

Street:

Postal Code/City:

Country:

Phone:

Fax:

Index

User's Manual Index-1



Index

A AC adapter

connecting, 2-5 Additional Options, 6-8 Audio Devices

connecting, 6-6

B Backing Up Your Files, 3-7 battery

alarms, 4-7 changing, 4-8 charging, 2-6, 4-3 conserving power, 4-6 disposal, 4-9 LED, 1-3 monitoring power, 4-5 RTC

charging, 4-4 Bluetooth/Modem Module Cover,

1-9 brightness

adjusting, 2-11 buttons

Internet, 1-13, 3-8 TOSHIBA Console, 1-13, 3-8 TV Out, 1-13

C CD

inserting, 3-10 Mode, 5-6 playing, 3-10, 5-5 removing, 3-10

CD/Digital Mode Button, 1-1, 1-2 CD-ROM drive

problems, 7-9 Character keys, 3-3

Communications setting up, 3-17

computer caring, 3-20 lock, 3-16 registering, 2-13 turning off, 3-20 turning on, 2-9

Computing Tips, 3-2 Covers

Bluetooth/Modem Module, 1-9 Memory Module, 1-9 Wireless LAN Card Module, 1-9

Ctrl, Fn, and Alt keys, 3-3

D DC-IN, 1-8

LED, 1-3 Digital Mode, 5-7 disk drive

problems, 7-7 display

problems, 7-6 display latch, 1-1 DVD

playing, 5-5

E External Monitor

connecting, 6-4 port, 1-8

F FIR port, 1-6, 5-7 Function keys, 3-3

Satellite P20

User's Manual 1

Index




H Headphone Jack, 1-5 Hot swapping, 3-13 Hotkeys, 2-11, A-1

I i.LINK port, 1-6 Internet button, 1-13, 3-8

K Keyboard, 1-11

Caps Lock LED, 1-11 Character keys, 3-3 Ctrl, Fn, and Alt keys, 3-3 Cursor Lock LED, 1-11 Function keys, 3-3 Num Lock LED, 1-11 Overlay keys, 3-4 problems, 7-5 using, 3-3 using USB, 6-2 Windows® special keys, 3-4

L LAN Jack, 1-7 LCD Screen, 1-10 Line-In

connecting, 6-7 Jack, 1-5

M Main Hard Drive

LED, 1-4 memory, 6-9

installing additional, 6-9 problems, 7-3

Memory Module Cover, 1-9 Microphone

connecting, 6-7 Jack, 1-5

Mode CD, 5-6 Digital, 5-7

modem problems, 7-13

Modem Jack, 1-6

Module Lock, 1-9 Release Latches, 1-9

Module Bay LED, 1-4

Mouse connecting, 2-8 USB, 6-3

Multiple displays, 5-1

O Optical drives, 3-10

using, 3-9 Overlay keys, 3-4

P Parallel port, 1-8 PC Card

hot swapping, 3-13 inserting, 3-12 problems, 7-10 removing, 3-13 using, 3-11

PC Card Slots, 1-6 Peripherals, 6-1 Playing compact discs, 3-10 Ports

2nd Module Bay, 1-2 DC-IN, 1-8 External Monitor, 1-8 FIR, 1-6, 5-7 Headphone Jack, 1-5 i.LINK port, 1-6 LAN Jack, 1-7 Line-In Jack, 1-5 Main Module Bay, 1-2 Microphone Jack, 1-5 Modem Jack, 1-6 Parallel, 1-8 PC Card

Slots, 1-6 Remote Control Receiver, 1-1 SD Card Slot, 1-6 TV Out, 1-6 USB, 1-6, 1-8

Power Button, 1-11 LED, 1-3 Power Management Utility,

5-10 problems, 7-4

Precautions, 3-1 Printer

connecting, 2-7 problems, 7-12

Printing, 3-7

Index




Problems, 7-1 CD-ROM drive, 7-9 disk drive, 7-7 display, 7-6 keyboard, 7-5 memory, 7-3 modem, 7-13 PC Card, 7-10 power, 7-4 printer, 7-12 sound system, 7-9

Program starting, 3-5

R Remote Control, 5-8

Receiver, 1-1 Restoring the pre-installed

software, 3-21

S Saving, 3-6 SD Card

inserting, 3-14 LED, 1-4 removing, 3-15 Slot, 1-6 using, 3-14

Security Lock Slot, 1-5 Setting Up Communications, 3-17 Setting Up Your Computer, 2-5 sound system

problems, 7-9 Starting A Program, 3-5

StickyKeys, 2-13, 3-8 System status indicators, 1-3

T Television

connecting, 6-5 TOSHIBA Console button, 1-13,

3-8 TOSHIBA’s Online Resources, 3-21 Touch pad, 1-12

Control Buttons, 1-12 using, 2-10

TV Out button, 1-13 port, 1-6

U USB port, 1-6, 1-8 Using PC Cards, 3-11 Using SD Cards, 3-14

V Volume Control, 1-5

W Windows® special keys, 3-4 Wireless Communication

LED, 1-4 Switch, 1-5

Wireless LAN using, 5-9

Wireless LAN Card Module Cover, 1-9

computers.toshiba-europe.com p20...

Documents