oti 6500 trio specification - skarby kosmosu...2015/07/14 · contactless reader, which supports...

Confidential & Proprietary Version 1.5

oti 6500 TRIO Specification

Version 1.5

Notice

This manual contains intellectual property including but not limited to, trade secrets and know-how, operation procedures and production procedures that belong solely to oti.

Disclosure, use, and/or production of any part of the above are strictly forbidden, except under a written license from oti.

Oti 6500 TRIO Specification Version 1.5

FCC Compliance

Confidential & Proprietary page B

FCC Compliance The 6500 reader complies with Part 15, of the FCC rules.

Operation is subject to the following conditions:

1. This device may not cause harmful interference,

and

2. This device must accept any interference received, including interference

that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15, subpart C of the

FCC rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications.

Changes or modifications in this equipment, not expressly approved by

the party responsible for compliance (On Track Innovations Ltd.) could

void the user’s authority to operate the equipment.

FCC ID: JNX-OTI-SAT6500

Responsible Party:

On Track Innovations LTD..

Z.H.R Industrial Zone.

Rosh Pina 12000

ISRAEL

Phone: +972-4-6868000

Email: [email protected]

mailto:[email protected]


Table of Contents

Confidential & Proprietary page 1

Table of Contents FCC COMPLIANCE ..................................................................................................................................... B

TABLE OF CONTENTS ................................................................................................................................ 1

TABLE OF FIGURES .................................................................................................................................... 2

1 INTRODUCTION .................................................................................................................................. 3

1.1 CERTIFIED AND SUPPORTED APPLICATIONS ...................................................................................... 4 1.2 SUPPORTED STANDARDS .................................................................................................................. 5

2 BASIC OPERATION ............................................................................................................................. 6

2.1 MAGNETIC STRIPE ............................................................................................................................ 7 2.2 CONTACTLESS .................................................................................................................................. 7 2.3 CONTACT .......................................................................................................................................... 7

3 TECHNICAL SPECIFICATIONS ..................................................................................................... 10

3.1 PRODUCT FEATURES ....................................................................................................................... 10 3.2 PRODUCT TECHNICAL SPECIFICATIONS .......................................................................................... 11

4 INTERFACE ......................................................................................................................................... 13

4.1 PIGTAIL CABLE WITH DEFAULT CONNECTOR ................................................................................. 13 4.2 PIGTAIL CONNECTOR CABLE WIRING ............................................................................................. 14

5 DIMENSIONS ...................................................................................................................................... 15

5.1 6500 TRIO ..................................................................................................................................... 15 5.2 SPACER ........................................................................................................................................... 16 5.3 MOUNTING PLATE .......................................................................................................................... 17 5.4 DRILLING TEMPLATE ...................................................................................................................... 18

6 INSTALLATION .................................................................................................................................. 19

6.1 ASSEMBLY IN BILL ACCEPTOR CUTOUT ......................................................................................... 19 6.2 SURFACE MOUNTING ON VENDING MACHINE (WITHOUT BILL ACCEPTOR CUTOUT) ..................... 20

7 CRADLE ............................................................................................................................................... 21

7.1 6500 TRIO FOR ATTENDED USE ..................................................................................................... 21 7.2 CRADLE STRUCTURE ...................................................................................................................... 22

8 CONTACT US ...................................................................................................................................... 24


Table of Figures


Table of Figures

Figure ‎2-1: 6500 TRIO – Front View ................................................................................................ 8

Figure ‎2-2: 6500 TRIO Full and Partial Configuration ...................................................................... 9

Figure ‎4-1: 6500 TRIO with Pigtail Connector Cable ..................................................................... 13

Figure ‎4-2: Pigtail Connector Cable Wiring .................................................................................... 14

Figure ‎5-1: 6500 TRIO Dimensions ................................................................................................. 15

Figure ‎5-2: Spacer Dimensions ........................................................................................................ 16

Figure ‎5-3: Spacer Picture ................................................................................................................ 16

Figure ‎5-4: Mounting Plate Dimensions .......................................................................................... 17

Figure ‎5-5: Mounting Plate Picture .................................................................................................. 17

Figure ‎5-6: Drilling Template .......................................................................................................... 18

Figure ‎7-1: 6500 TRIO within its Cradle ......................................................................................... 21

Figure ‎7-2: Cradle parts.................................................................................................................... 22

Figure ‎7-3: Cradle Dimensions ........................................................................................................ 23


Introduction


1 Introduction The 6500 TRIO reader is a modular payment device that can support up to three cashless payment

interfaces in one small stylish enclosure. The reader is designed specifically for installation in

vending machines to allow cashless payment with magnetic payment cards, as well as proximity,

vicinity, and Contact EMV payment cards.

This device contains three reader interfaces:

Magnetic card swipe reader, which contains a vertical card swipe slot supporting Track 1 and

Track 2 data.

Contactless reader, which supports ISO/IEC 14443 A&B proximity and ISO/IEC 15693

vicinity tags and cards. The reader supports the major financial contactless programs.

Contact interface, which supports all EMV financial chip cards.

LCD, LEDs and a buzzer give the user quick transaction confirmation and clear interactive

feedback. The 6500 TRIO uses oti’s patented matched antenna technology.

The reader modular design allows customers to order the reader using a wide collection of

hardware configurations, for example:

Contactless, Contact and Mag-Stripe

Contactless and Mag-Stripe only

Contactless and Contact only

Contact and Mag-Stripe only

Contactless only

Contact only

Mag-Stripe only

The 6500 TRIO reader can be ordered with a wide range of hardware options and accessories such

as:

Standard and customized communication cables

Standard and customized front stickers

User interface buttons

110V, 220V or 110/220V power supply

Mounting accessories

More


Introduction


1.1 Certified and Supported applications The 6500 TRIO is certified and supports the following

applications:

EMV

o Contact EMV L1

o Contact EMV L2

o Contactless EMV L1

VISA

o VISA PayWave MSD

o VISA PayWave qVSDC

o NDOT over VISA for transportation

o VISA Global Transit Payment Pilot Specification

o VISA Pilot Visa PayWave Ticketing Extension Specification

o VISA Asia Pacific WAVE 2

MasterCard

o MasterCard PayPass M/Chip (including Data Exchange)

o MasterCard PayPass Mag Stripe

o NDOT over MasterCard for transportation

American Express

o AMEX ExpressPay

Discover

o Discover ZipNetwork

Interac

o Interac Flash

SoftCard

o SoftCard (ISIS) SmartTap

Mifare

o Mifare Ultralight

o Mifare Classic

o Mifare DESFire (optional)

Transparent (Pass-Through) Communication

o ISO/IEC 14443 Type A - Transparent Proximity

o ISO/IEC 14443 Type B - Transparent Proximity

o ISO/IEC 15693 Vicinity (optional) - Transparent Vicinity

Other

o Magnetic Stripe Card – ISO/IEC 7813, Track 1 + Track 2

o Additional proprietary applications


Introduction


1.2 Supported Standards The 6500 TRIO is compatible with the following standards:

FCC

CE

UL

RoHS compliance

ISO 9001: 2008

ISO/IEC 14443 Proximity Type A&B

ISO/IEC 15693 Vicinity

ISO/IEC 7813

Mifare

MasterCard TQM label

IP65


Basic Operation


2 Basic Operation As stated in Chapter ‎0 Table of Figures

Figure ‎2-1: 6500 TRIO – Front View ................................................................................................ 8

Figure ‎2-2: 6500 TRIO Full and Partial Configuration ...................................................................... 9

Figure ‎4-1: 6500 TRIO with Pigtail Connector Cable ..................................................................... 13

Figure ‎4-2: Pigtail Connector Cable Wiring .................................................................................... 14

Figure ‎5-1: 6500 TRIO Dimensions ................................................................................................. 15

Figure ‎5-2: Spacer Dimensions ........................................................................................................ 16

Figure ‎5-3: Spacer Picture ................................................................................................................ 16

Figure ‎5-4: Mounting Plate Dimensions .......................................................................................... 17

Figure ‎5-5: Mounting Plate Picture .................................................................................................. 17

Figure ‎5-6: Drilling Template .......................................................................................................... 18

Figure ‎7-1: 6500 TRIO within its Cradle ......................................................................................... 21

Figure ‎7-2: Cradle parts.................................................................................................................... 22

Figure ‎7-3: Cradle Dimensions ........................................................................................................ 23


Basic Operation


Introduction, the 6500 TRIO reader contains three card interfaces:

Magnetic card swipe reader

Contactless reader

Contact reader

2.1 Magnetic Stripe When a valid magnetic payment card is swiped, the reader reads Track 1

and Track 2 data stored on the card’s magnetic stripe. If the data is valid, the

unit will display a row of 4 LEDs that light up in sequence followed by a

beep. The reader then communicates the transaction data to the Host.

The interactive LCD, LEDs, and buzzer give the user an indication of the

transaction status.

2.2 Contactless When a valid contactless payment card is presented to the reader, the reader

performs a payment transaction with the contactless card. If the transaction

is accepted, the unit will display a row of 4 LEDs that light up in sequence

followed by a beep. The reader then communicates the transaction data to

the Host.

A landing zone logo on the graphic overlay under the reader’s LCD

indicates where the contactless card or tag should be presented.


transaction status.

2.3 Contact When a valid EMV contact chip card is inserted into to the reader contact

slot, the reader performs a payment transaction with the contact card. If the

transaction is accepted, the unit will display a row of 4 LEDs that light up in

sequence followed by a beep. The reader then communicates the transaction

data to the Host.


transaction status.


Basic Operation


Figure ‎2-1: 6500 TRIO – Front View

Button

#1

Button

#2

Button

#3

16x2 Character

LCD Display

Contactless payment applications logos

LED

Contact Contactless Magnetic

Payment transaction LEDs

Magnetic card swipe

Contact card

slot

Graphic Overlay *

* Overlay artwork can be customized to customer requirements

Buttons (Optional)

Card interface logos

Logos (Optional)


Basic Operation


Figure ‎2-2: 6500 TRIO Full and Partial Configuration


Technical Specifications


3 Technical Specifications

3.1 Product Features General

Flexible, software configurable,

certified intelligent reader solution

oti advanced Host – Reader TLV based

protocol

Contactless transparent communication

support

Modular design by Hardware and Software

Tamper-proof remote software update

Available as OEM

RF Interface

Bi-directional RF interface

between Reader and Contactless Smart

Cards

Carrier frequency: 13.56 MHz

ISO/IEC 14443 Type A/B and Mifare full

support

Optional I-Code and ISO/IEC 15693 support

Communication Links

RS 232, 8 data bits, no parity, 1 stop bit,

full 8-bit binary data.

Client defined baud rate

TTL level or RS 485 support (Optional)

USB 2.0 – full speed, CDC (Optional)

Default connectors:

Communication & Power: Pigtail.

Note: Pigtail termination can be customized

Environmental Conditions

Operating: -30° to 70°C (-22° to 158°F)

User Interface

2 x 16 character display

4 LED indicators

Multi-tone buzzer

Up to 3 buttons (Optional)

“Button-Led" (Optional)

Electronic Board Power Requirements

8VDC - 45VDC (On-board Switch Mode

Power Supply).

Max power consumption

3W (RF signal ON)

SAM Interface

One optional Slot, ISO/IEC 7816 compliant

Magnetic Interface

Magnetic Card Reader

1,000,000 passes minimum

Contact Interface

EMV contact chip support

Security

High security encryption system

(3DES/AES/RSA) protects the reader’s

operating system

Vandalism-proof PKI protected software

update mechanism

DUKPT (Derived Unique Key Per

Transaction) support

Offline PIN Authentication support

Secure boot loader (firmware update)

protocol




3.2 Product Technical Specifications

Table ‎3-1: Performance/Electrical Specifications

Feature Specification RF Interface:

RF Carrier Frequency 13.56 MHz

RF Output 450mW

ISO/IEC 14443 A&B and Mifare Full compliance

ISO/IEC 15693 Optional

Magnetic card head:

Head Life 1,000,000 Min Passes

EMV Contact interface

SAM Interface (Optional)

Communication Links:

RS232, RS485, USB or TTL

Default Pigtail cable connector Molex MicroFit 43025_0600

Indicators:

2x16 LCD with backlight

Display size: 2.58/0.98” (65.5/25mm)

Character size: 0.2/0.1” (5/2.55mm)

Operating temperature:

-22°F to 176°F (-30°C to 80°C)

Four programmable on-board

LEDs

4 Green super bright transaction feedback LEDs

1 “Button-Led”

Buzzer Multi-tone buzzer (up to 5VDC)

Buttons:

Buttons support Up to 3 buttons

Buttons durability 1,000,000 operations min.

Magnetic head decoder

Electronic Board Power Requirements:

8VDC - 45VDC On-board switching power supply

Maximum power consumption 3W (RF signal ON)

Mechanical (without contact interface):

Dimensions H – 4.1665” (105.83mm)

W – 3.23” (82mm)

D - 1.46” (37mm)

Weight 212 gr.

Vibrations 10 200 Hz @ 2.0G

Mechanical (with contact interface):

Dimensions H – 4.1665” (105.83mm)

W – 3.54” (90mm)

D - 1.46” (37mm)

Weight 240 gr.

Vibrations 10 200 Hz @ 2.0G

Temperature:

Operating -30°C to 70°C (-22°F to 158°F)




Warning: Power supply minimum requirements

Keeping the DC supply voltage within the specified allowed range is crucial

to guarantee proper operation of the equipment. The use of AC rectified

power supply source, which is not properly filtered, forms a risk of too low

voltage dips and hence should be avoided. It is highly recommended to

check this issue with proper tools (e.g. oscilloscope) during the reader

installation. For more details contact oti technical team via oti’s sales

representatives.


Interface


4 Interface

4.1 Pigtail Cable with Default Connector

Figure ‎4-1: 6500 TRIO with Pigtail Connector Cable

The 6500 TRIO has a 23.6” (60cm) pigtail connector cable terminated with

a Molex MicroFit 43025_0600 6-pin female connector.

The cable supplies DC power and RS232 serial communication to the reader.

Molex

MicroFit 43025_0600

female connector

Pigtail connector

cable


Interface


4.2 Pigtail Connector Cable Wiring

Figure ‎4-2: Pigtail Connector Cable Wiring

Molex MicroFit connector pin designation:

Pin 1: (Screen) Cable screen wire

Pin 2: (TXD) Reader RS232 Transmit line

Pin 3: (V+) Reader 8 to 45V DC Power input

Pin 4: (RXD) Reader RS232 Receive line

Pin 5: (GND)

Pin 6: Not used

Saturn 6500 MB

VIN

GND

TR (RXD)

TR* (TXD)

SCREEN

Saturn 6500 Pigtail

23.6" (60cm)

Red

Black

White

Green

28AWG

14

25

36

MicroFit 43025-0600Connector


Dimensions


5 Dimensions

5.1 6500 TRIO

Figure ‎5-1: 6500 TRIO Dimensions

Front Side

3.23"

(82mm)

1.46"

(37mm)

4.1665"

(105.83mm)

3.54"

(90mm)

Without contact reader

With contact reader


Dimensions


5.2 Spacer The Spacer is used to elevate the 6500 TRIO from the mounting surface.

Spacers can be stacked.

Caution:

Use the mounting screws provided with the spacer kit. Use of longer

screws may damage the reader.

Figure ‎5-2: Spacer Dimensions

Figure ‎5-3: Spacer Picture

3.154"

(80.11mm)

4.082"

(103.68mm)

0.626"

(15.90mm)

0.744"

(18.90mm)


Dimensions


5.3 Mounting Plate The mounting plate is used for installation of the 6500 TRIO in bill acceptor

cutout. The dimensions are shown in the figure below.

Figure ‎5-4: Mounting Plate Dimensions

Figure ‎5-5: Mounting Plate Picture


Dimensions


5.4 Drilling Template The drilling template (illustrated in the figure below) is used to mark the

position of the mounting holes and cable entry hole that need to be drilled

into installations where there is no bill acceptor cutout.

Figure ‎5-6: Drilling Template


Installation


6 Installation

6.1 Assembly in Bill Acceptor Cutout The 6500 TRIO is designed to fit into the bill acceptor cutout.

If the vending machine has a bill acceptor cutout, please perform the

following steps:

1. Take the mounting plate (see Figure ‎5-4) supplied with the kit and

attach it to the reader (see Figure ‎5-1) with four 8mm long

mounting screws.

2. Open the vending machine door and remove the cutout cover. Hold

onto the cover mounting nuts; They will be used later (see Step ‎4) to

secure the reader to the vending machine door.

3. Insert the reader through the cutout from the inside, allowing the

bolts surrounding the cutout to pass through the cutouts in the

mounting plate.

4. Use the cover mounting nuts (See Step ‎2) to secure the reader to the

vending machine door.

5. Connect the MicroFit connector on the reader pigtail (see Figure ‎4-1

and Figure ‎4-2) to the MicroFit connector on the communication

cable.

6. Verify functionality.

7. Installation is complete.


Installation


6.2 Surface Mounting on Vending Machine (without Bill Acceptor Cutout)

If the vending machine doesn’t have a bill acceptor cutout:

1. Take drilling template (see Figure ‎5-6) supplied with kit and place it

over the mounting location.

2. Drill four 0.2” holes and one 0.5” hole as shown in Figure ‎5-6.

3. Insert pigtail (see Figure ‎4-1 and Figure ‎4-2) from outside through

the 0.5” hole. Insert four 8mm long mounting screws supplied with

kit from inside and use them to secure the reader to the vending

machine door.

4. Connect the MicroFit connector (see Figure ‎4-1 and Figure ‎4-2) on

the reader pigtail to the MicroFit connector on the communication

cable.

5. Verify functionality.

6. Installation is complete.


Cradle


7 Cradle

7.1 6500 TRIO for Attended Use

The 6500 TRIO can be delivered ready for attended use configuration.

While installed within its cradle, the 6500 TRIO can be used as a triple

channel (3-in-1) countertop reader.

The 6500 TRIO supports card associations operation profiles for both

attended and unattended use.

Figure ‎7-1: 6500 TRIO within its Cradle


Cradle


7.2 Cradle Structure

The 6500 TRIO cradle is designed to be light and easy to install.

The cradle consists of two physical parts as illustrated in the figure below.

Figure ‎7-2: Cradle parts


Cradle


The cradle dimensions (164.10 mm x 112.11 mm) are relatively compact in order to minimize the

counter space required for the reader.

Figure ‎7-3: Cradle Dimensions


Contact Us


8 Contact Us

For oti America Technical Support (US and Canada):

Phone: +201-944-5200 (Ext. 140) 08:30 AM - 06:00 PM Eastern time

Monday through Friday


For oti Technical Support (International):

Phone: +972-4-6868000 (Ext. 8090)




oti 6500 trio specification - skarby kosmosu...2015/07/14 · contactless reader, which supports...

Documents