optional_side_struts_for_microwave_antennas

Visit www.commscope.com/andrew or contact your local Andrew Solutions representative for more information.

© 2010 CommScope, Inc. All rights reserved. Andrew Solutions is a trademark of CommScope. All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement any specifications or warranties relating to Andrew products or services.

TP-104088-EN (6/10) 1 of 3

Technical Publication Optional Side Struts for Microwave Antennas Optional Struts and Accessories for 8, 10, and 12 ft Diameter Antennas A) Reflector Strut Brackets, Type Number 520568

Two brackets attach to the edge of 8, 10, and 12 ft reflectors to provide an attachment point for the fixed side strut. Brackets are cast aluminum and the kit contains hardware for attachment to the reflector. Quantity: 2 per kit.

B) Adjustable Inboard Strut Kit, Type Number 520570-1 Azimuth wind brace with threaded rod adjustment assembly allows

for fine antenna alignment. Galvanized steel pipe and brackets include all hardware for attachment to antenna mount or reflector mounting ring. Also includes item D and G for tower end attachment. Strut pipe is 10.5 ft (3.2 m) in length.

C) Fixed Inboard Strut Kit, Type Number 520570-2 Azimuth wind brace. Galvanized steel pipe and brackets include all

hardware for attachment to antenna mount or reflector mounting ring. Also includes item G for tower end attachment. Strut pipe is 10.5 ft (3.2 m) in length.

D) Azimuth Adjustment Kit, Type Number 520569

Attaches to inboard side strut (and strut collar assembly) to allow fine adjustment of the antenna during final alignment. Straight threaded rod assembly and associated hardware included. Order strut collar clamp item G separately.

E) Outboard Strut Kit, Type Number 520570-3

Galvanized fixed side strut provides increased rigidity. Kit includes universal joint and hardware for attachment to reflector strut bracket (item A) included. Strut collar assembly (item G) also included to provide interface to tower. Strut pipe is 10.5 ft (3.2 m) in length.

F) Outboard Strut Replacement Kit, Type Number 520570-4 Includes item G less item A reflector bracket.

G) Strut Collar Assembly, Type Number 520477

Provides tower interface and strut securement point. Galvanized clamp assembly includes all hardware. H) Bottom Strut Kit, Type Number 520570-5 Provides additional support to an antenna under conditions of high ice loads. Reflector strut bracket,

galvanized strut pipe, strut collar assembly, and (pipe mount) angle interface bracket included associated hardware is galvanized. Strut is 10.0 ft (3.05 m) in length.

A

B, C

D

H G

E, F

ASuitable Tower or Support Structure Member (not supplied)

4.5 in (115 mm) Diameter Mounting Pipe (not supplied)

Reflector

ReflectorMounting Ring



TP-104088-EN (6/10) 2 of 3

Technical Publication. Optional Struts for 4 and 6 ft Diameter Antennas (2009 models onward) Inboard Strut Kit (less azimuth adjustment), Type Number VSTRUT-P3KIT

Optional fixed side strut for strut for 4 ft (1.2 m) and 6 ft (1.8 m) TMW and ValuLine™ antennas. Does not include azimuth adjustment. All hardware is included. Strut is 5.0 ft (1.52 m) in length. Inboard Strut Kit (less azimuth adjustment), Type Number 520570-10 Optional fixed side strut for strut for 4 ft (1.2 m) and 6 ft (1.8 m) TMW and ValuLine antennas. Does not include azimuth adjustment. All hardware is included. Strut pipe is 10.5 ft (3.2 m) in length. Optional Strut for ValuLine™ VHLP(X)3 Antenna Inboard Strut Kit (less azimuth adjustment), Type Number VSTRUT-3KIT Optional fixed side strut for ValuLine VHLP(X)3 antennas. All hardware is included. Strut is 5 ft (1.52 m) in length. Strut attaches to pole diameter 65 mm–115 mm (not supplied).

POLE 65-115

4 Ft.6 Ft.6 ft 4 ft



TP-104088-EN (6/10) 3 of 3

Technical Publication Optional Struts for 4 and 6 ft Antennas (prior to 2009)

• 1.2 m ValuLine™ antennas (VHP4 are prior to 2009) use VSTRUT-P3KIT as an optional fixed side strut. This will fit all earlier ValuLine 1.2 m antennas.

• 1.2 m TMW antennas (2000–2009) use VSTRUT-P3KIT as an optional fixed side strut.

• 1.2 m TMW antennas (prior to 2000), 1.8 m TMW and ValuLine antennas (prior to 2009) using

T6MSB/T6MSC style mount. A) Adjustable Inboard Strut Kit, Type Number 520570-1

Azimuth wind brace with threaded rod adjustment assembly allows for fine antenna alignment. Galvanized steel pipe and brackets include all hardware for attachment to antenna mount or reflector mounting ring. Also includes item C and D (shown in image to the right) for tower end attachment. Strut pipe is 10.5 ft (3.2 m) in length.

B) Fixed Inboard Strut Kit, Type Number 520570-2 Azimuth wind brace. Galvanized steel pipe and brackets

include all hardware for attachment to antenna mount or reflector mounting ring. Also includes item D for tower end attachment. Strut pipe is 10.5 ft (3.2 m) in length.

C) Azimuth Adjustment Kit, Type Number 520569

Attaches to inboard side strut (and strut collar assembly) to allow fine adjustment of the antenna during final alignment. Straight threaded rod assembly and associated hardware included. Order strut collar clamp item D separately.

D) Strut Collar Assembly, Type Number 520477

Provides tower interface and strut securement point. Galvanized clamp assembly includes all hardware.

MountingRing

B, C, L

D

G

C--

D--

A, B--

optional_side_struts_for_microwave_antennas

Documents