opt 11e cisco e1-r2 cas

Cisco 3640 Gateway-PBX Interoperability: Nortel Meridian Opt11E with E1-R2 CAS Signaling This document describes the interoperability and configuration of a Cisco 3640 voice gateway with a Nortel Meridian Opt11E PBX using E1-R2 CAS signaling. It includes the following sections:

• System Components • Configuration Tasks • Caveats

System Components

PBX Model Nortel Meridian Opt11E

PBX Release Software Version Release 21 Telephony Signaling E1 R2

Voice Gateway Cisco 3640

Gateway Release IOS™ Version 12.2(2)T1

VoX Protocol H.323

CallManager Release 3.1

Configuration Tasks See the following sections for configuration tasks for this feature:

• Set Up • Nortel Meridian Option 11E PBX Sample Configuration • Call Manager Configuration • Cisco 3640 Gateway Configuration

Cisco 3640 Gateway-PBX Interoperability: Nortel Meridian Opt11E with E1-R2 CAS Signaling

Set Up This section includes the following information:

• Connectivity Diagrams • Set Up Notes

Connectivity Diagrams

Figure 1: Test Configuration

Figure 1 represents the configuration used for testing: a Nortel Meridian Opt11E connected to a Cisco 3640 voice gateway via an E1 R2 connection. Set Up Notes

• Automatic number identification (ANI) feature is supported.

Nortel Meridian Option 11E PBX Sample Configuration Configure in the following sequence:

1.

Phone Cx4001

Basic Call Setup End-to-End Configuration

VoIP

Cisco Call ManagerRelease 3.1

Phone Bx3502

Phone Dx4002

Phone Ax3501

PBX #1

Phone Ex5000

PBX1: Nortel Opt11E

E1-R2

3640

Cat 6KEthernetSwitch

Cisco 7960 IP phones


Configure Common Equipment 2. Configure Route Data Block 3.


Configure Trunk 4. Configure Signaling Category 5. Configure Multifrequency Compelled Signaling Table 6. Configure Digital Station Phone 7. Configure External Multi-frequency Sender/Receiver Board


Configure Common Equipment LD 22 PT2000 MARP NOT ACTIVATED REQ PRT TYPE CEQU CEQU MPED 8D SUPL 000 004 008 012 016 032 036 040 048 P064 XCT 008 000 CONF 029 030 031 DTI2 02 MISP MTYP 384K REQ **** > Configure Route Data Block >LD 21 PT1000 REQ: PRT TYPE: RDB CUST 0 ROUT 102 TYPE RDB CUST 00 DMOD ROUT 102 TKTP DID SAT NO RCLS EXT DTRK YES DGTP DTI2 ISDN NO DSEL VCE PTYP DTO AUTO NO DNIS NO ICOG IAO RANX NO SRCH LIN STEP ACOD 702 TARG BILN NO OABS INST MFC R2MF MFCI 1 R2MD NO SGL NO BSSU NO MFCO 2 OPP NORM SWP NORM TIMR MFC 12032 MFO 0 ICF 512 OGF 512 EOD 13952 DSI 34944 NRD 10112 DDL 70 ODT 4096 RGV 640


FLH 510 GTO 896 GTI 896 SFB 3 TFD 0 SST 5 0 DTD NO SCDT NO 2 DT NO NEDC ETH FEDC ETH CPDC NO DLTN NO HOLD 02 02 40 SEIZ 02 02 SVFL 02 02 OPCB NO DDO NO DRNG NO CDR NO CCO NO NATL YES SSL CFWR NO IDOP YES MUS NO MR NO PANS YES RACD NO RUCS 0 EQAR NO FRL 0 0 FRL 1 0 FRL 2 0 FRL 3 0 FRL 4 0 FRL 5 0 FRL 6 0 FRL 7 0 TTBL 0 OHTD NO PLEV 2 OPR NO PRDL NO DNSZ 0 RCAL NO MCTS NO ALRM NO BTT 30 ACKW NO NCNI 0 CNIE NO CNIT YES CTAT YES ART 0 OPDL 0 PECL NO DCTI 0 NADT 0 SGRP 0 REQ: **** >


Configure Trunk >LD 20 PT0000 MARP NOT ACTIVATED REQ: PRT TYPE: TNB TN 2 1 DATE PAGE DES TN 002 01 TYPE DID CUST 0 TRK DTI2 SICA 3 PDCA 1 PCML A NCOS 0 RTMB 102 1 NITE CLS UNR MFC CNA WTA LPR APN THFD BARD P10 MFL 4 MFPD NO TKID DTCR NO DATE 10 APR 1993 NACT **** >

Configure Signaling Category SIGNALING CATEGORY 3 (SICA 3) CONFIGURATION FOR IMMEDIATE START >LD 73DDB000 UDATA: 067959 0 PDATA: 065844 44 DISK RECS AVAIL: 512 REQ PRT TYPE DTI2 FEAT ABCD SICA 3 TNLS IN/OUT CALLS IDLE (S) 1101 IDLE (R) 1101 FALT (S) 1001 FALT (R) 1001 P RRC (S) UNUSED INCOMING CALLS E SEZ (R) 0101 SEZD (R) UNUSED SEZV (R) UNUSED P CALL (R) UNUSED SEZA (S) 1101 TIME 150 FSZA NO PRCS (S) UNUSED P WNKS (S) UNUSED P DIGT (R) UNUSED NRCV (S) UNUSED P EOSF (S) UNUSED EOSF (S) UNUSED P EOSB (S) UNUSED EOSB (S) UNUSED P OPCA (R) UNUSED E CONN (S) 0101 CONN (R) 0001 P BURS (S) UNUSED P BURS (R) UNUSED C CLRB (S) 1101 P RCTL (S) UNUSED


P RCOD (S) UNUSED P OPRS (R) UNUSED P NXFR (S) UNUSED P ESNW (S) UNUSED P CAS (S) UNUSED CLRF (R) UNUSED SOS (R) UNUSED OUTGOING CALLS E SEZ (S) 0101 SEZD (S) UNUSED SEZV (S) UNUSED SEZA (R) 1101 P WNKS (R) UNUSED P EOS (R) UNUSED CONN (S) 0001 E CONN (R) 0101 P OPRC (R) UNUSED P BURS (S) UNUSED P BURS (R) UNUSED C CLRB (R) 1101 P RCTL (R) UNUSED P NXFR (R) UNUSED P ESNW (R) UNUSED P CAS (R) UNUSED CLRF (S) UNUSED SOS (R) UNUSED UDATA: 067959 0 PDATA: 065844 44 DISK RECS AVAIL: 512 REQ **** >

Configure Multifrequency Compelled Signaling Table INCOMING CALL MULTIFREQUENCY COMPELLED SIGNALING TABLE >LD 94MFCT000 UDATA: 067959 0 PDATA: 065844 44 DISK RECS AVAIL: 512 REQ PRT TYPE R2MFICOG ICTTBNO 1LVNO TYPE R2MF ICOG ICT MAXT 2 TBNO 1 EECD 1 SMFC NO SCNT NO LVNO 1 RECV 1 DGT1 2 DGT2 3 DGT3 4 DGT4 5 DGT5 6 DGT6 7 DGT7 8 DGT8 9 DGT9 10 DGT0 11 HTDM 15 EODL XMIT NEXT 1 TERM 6 COMP 3 CONG 4


SCAT 5 SCNI 5 FAIL 15 TYPE R2MF ICOG ICT MAXT 2 TBNO 1 EECD 1 LVNO 2 RECV 1 NOPR 2 PRIO 3 NOPR 5 OPER 6 NOPR 7 REST 8 NOPR 9 PRIO 10 OPER 11 NOPR 12 NOPR 13 NOPR XMIT IDLE 6 BUSY 3 CONG 4 VACC 5 OUTT 8 FAIL 9 REQ **** > OUTGOING CALL MULTIFREQUENCY COMPELLED SIGNALING TABLE REQ PRTTYPE R2MFICOG OGTTBNO 2LVNO TYPE R2MF ICOG OGT MAXT 2 TBNO 2 SET 1 ATT 1 TIE 6 NTT 6 EECD 2 SMFC YES SCNT NO LVNO 1 RECV 1 NEXT 2 TNM1 3 COMP 4 CONG 5 CCNI 6 TERM 7 TNM2 8 TNM3 9 SCNI 10 TFST 11 TNXT 15 FAIL XMIT DGT1 1 DGT2 2 DGT3 3 DGT4 4 DGT5 5


DGT6 6 DGT7 7 DGT8 8 DGT9 9 DGT0 10 ECNI 15 EODL 15 TYPE R2MF ICOG OGT MAXT 2 TBNO 2 SET 1 ATT 1 TIE 6 NTT 6 EECD 2 LVNO 2 RECV 2 IDLE 3 BUSY 4 CONG 5 VACC 6 IDLE 8 OUTT 9 FAIL XMIT NOPR 1 OPER 5 REST 7 REQ **** > Configure Digital Station Phone >LD 11SL1000 UDATA: 067959 0 PDATA: 065844 44 DISK RECS AVAIL: 512 TNS AVAIL: 896 USED: 104 TOT: 1000 ACD AGENTS AVAIL: 1000 USED: 0 TOT: 1000 AST SET AVAIL: 100 USED: 0 TOT: 100 REQ: PRTTYPE: 2616 TN 001 0 0 0DATE PAGE DES DES TEST2 TN 001 0 00 00 TYPE 2616 CDEN 8D CUST 0 AOM 0 FDN TGAR 0 LDN NO NCOS 0 SGRP 0 RNPG 0 SCI 0 SSU XLST SCPW SFLT NO CAC 0 CLS UNR FBD WTA LPR MTD FND HTD ADD HFD MWD AAD IMD XHD IRD NID OLD VCE DRG1 POD DSX VMD CMSD CCSD SWD LND CNDA


CFTD SFD MRD PDN DDV CNIA ICDD CDMD LLCN MCTA AUTU GPUD DPUD DNDA CFXA ARHD CLTD ASCD CPFA CPTA HSPD ABDD DELD CFHD FICD NAID UDI RCC HBTD AHD DDGA NAMA MIND PRSD NRWD NRCD NROD EXR0 USRD ULAD OCBD CPND_LANG ENG HUNT PLEV 02 AST IAPG 0 ITNA NO DGRP MLWU_LANG 0 DNDR 0 KEY 00 SCR 3501 MARP CPND CPND_LANG ROMAN NAME BIG BIRD XPLN 20 DISPLAY_FMT FIRST,LAST 01 02 03 CFW 12 3502 04 AO6 05 TRN 06 DSP 07 08 ADL 16 09 ADL 16 10 ADL 16 11 ADL 16 12 ADL 16 13 ADL 16 14 ADL 16 15 TRN DATE 13 APR 1993 NACT **** >

Configure External Multi-frequency Sender/Receiver Board >LD 20 PT0000 REQ: PRTTYPE: MFCTN 008CDEN DATE PAGE TN 008 0 00 00 TYPE MFC CDEN 8D DATE 3 APR 1993 TN 008 0 00 01 TYPE MFC CDEN 8D DATE 3 APR 1993 DTC105 TN 008 0 00 02 TIM000 04:30 13/4/1993 CPU 0 TYPE MFC CDEN 8D DATE 3 APR 1993 TN 008 0 00 03 TYPE MFC CDEN 8D


DATE 3 APR 1993 NACT **** > OVL000

Call Manager Configuration Call Manager Version Information


Cisco 3640 Gateway Configuration The following is the configuration of the Cisco 3640 voice gateway connected to the Nortel Meridian Opt11E PBX interface. Cisco Catalyst 3650 Gateway Version Information


Route Pattern Configuration


Cisco 3640 Voice Gateway Version Information 3640#sh ver Cisco Internetwork Operating System Software IOS (tm) 3600 Software (C3640-JS-M), Version 12.2(2)T1, RELEASE SOFTWARE (fc2) TAC Support: http://www.cisco.com/tac Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Wed 18-Jul-01 00:58 by ccai Image text-base: 0x600089A8, data-base: 0x61654000 ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) 3640 uptime is 2 minutes System returned to ROM by power-on System image file is "slot0:c3640-js-mz.122-2.T1.bin" cisco 3640 (R4700) processor (revision 0x00) with 59392K/6144K bytes of memory. Processor board ID 19594643 R4700 CPU at 100Mhz, Implementation 33, Rev 1.0 Channelized E1, Version 1.0. Bridging software. X.25 software, Version 3.0.0. SuperLAT software (copyright 1990 by Meridian Technology Corp). TN3270 Emulation software. Primary Rate ISDN software, Version 1.1. 2 Ethernet/IEEE 802.3 interface(s) 2 Channelized E1/PRI port(s) 2 Voice FXS interface(s) DRAM configuration is 64 bits wide with parity disabled. 125K bytes of non-volatile configuration memory. 8192K bytes of processor board System flash (Read/Write) 16384K bytes of processor board PCMCIA Slot0 flash (Read/Write) Configuration register is 0x1921 3640#sh diag Slot 0: Combo 2E, 2W Port adapter, 4 ports Port adapter is analyzed Port adapter insertion time unknown EEPROM contents at hardware discovery: Hardware revision 1.2 Board revision C0 Serial number 15878958 Part number 800-01171-05 Test history 0x0 RMA number 00-00-00 EEPROM format version 1 EEPROM contents (hex): 0x20: 01 1E 01 02 00 F2 4B 2E 50 04 93 05 00 00 00 00 0x30: 60 00 00 00 99 10 06 17 FF FF FF FF FF FF FF FF Slot 1: High Density Voice Port adapter Port adapter is analyzed Port adapter insertion time unknown EEPROM contents at hardware discovery: Hardware Revision : 1.0 Top Assy. Part Number : 800-03567-01 Board Revision : A0 Deviation Number : 0-0 Fab Version : 02 PCB Serial Number : JAB033906YA RMA Test History : 00 RMA Number : 0-0-0-0 RMA History : 00 EEPROM format version 4 EEPROM contents (hex): 0x00: 04 FF 40 00 CC 41 01 00 C0 46 03 20 00 0D EF 01 0x10: 42 41 30 80 00 00 00 00 02 02 C1 8B 4A 41 42 30 0x20: 33 33 39 30 36 59 41 03 00 81 00 00 00 00 04 00 0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF


0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF WIC Slot 0: E1 (2 Port) Multi-Flex Trunk WAN Daughter Card Hardware revision 1.0 Board revision B0 Serial number 18779447 Part number 800-04479-01 Test history 0x0 RMA number 00-00-00 Connector type PCI EEPROM format version 1 EEPROM contents (hex): 0x20: 01 23 01 00 01 1E 8D 37 50 11 7F 01 00 00 00 00 0x30: 58 00 00 00 00 02 25 00 FF FF FF FF FF FF FF FF HDV firmware: Compiled Fri 23-Mar-01 00:20 by miriyala HDV memory size 524280 heap free 197609 Slot 2: 4 PORT Voice PM for MARs Port adapter Port adapter is analyzed Port adapter insertion time unknown EEPROM contents at hardware discovery: Hardware revision 1.0 Board revision B0 Serial number 7968450 Part number 800-02491-01 Test history 0x0 RMA number 00-00-00 EEPROM format version 1 EEPROM contents (hex): 0x20: 01 65 01 00 00 79 96 C2 50 09 BB 01 00 00 00 00 0x30: 58 00 00 00 98 04 01 17 FF FF FF FF FF FF FF FF WIC Slot 0: FXS Voice daughter card (2 port) Hardware revision 1.1 Board revision B0 Serial number 24298176 Part number 800-02493-02 Test history 0x0 RMA number 00-00-00 Connector type Wan Module EEPROM format version 1 EEPROM contents (hex): 0x20: 01 0E 01 01 01 72 C2 C0 50 09 BD 02 00 00 00 00 0x30: 58 00 00 00 01 02 05 01 FF FF FF FF FF FF FF FF

Cisco 3640 Voice Gateway Sample Configuration 3640#sh run Building configuration... Current configuration : 1600 bytes ! version 12.2 no parser cache no service single-slot-reload-enable service nagle service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname 3640 ! logging buffered 12800 debugging logging rate-limit console 10 except errors aaa new-model aaa group server tacacs+ AuRAS ! ! ! !


voice-card 1 ! ip subnet-zero ! ! no ip domain-lookup ! no ip dhcp-client network-discovery isdn switch-type primary-dms100 isdn voice-call-failure 0 call rsvp-sync voice rtp send-recv ! voice class codec 1 codec preference 1 g729r8 codec preference 2 g711ulaw codec preference 3 g711alaw ! ! ! ! ! ! ! controller E1 1/0 shutdown ! controller E1 1/1 framing NO-CRC4 ds0-group 1 timeslots 1-15,17-31 type r2-analog r2-compelled ani ! ! ! interface Ethernet0/0 ip address 10.18.1.2 255.255.255.0 no ip mroute-cache full-duplex no cdp enable ! interface Ethernet0/1 ip address 10.1.1.129 255.255.255.0 no ip mroute-cache half-duplex no cdp enable ! ip classless no ip http server ! no cdp run ! ! ! snmp-server manager ! voice-port 1/1:1 ! voice-port 2/0/0 ! voice-port 2/0/1 ! dial-peer cor custom ! ! ! dial-peer voice 3 voip destination-pattern 4... voice-class codec 1 session target ipv4:10.1.1.2


dtmf-relay h245-alphanumeric ip qos dscp cs5 media no vad ! dial-peer voice 4 pots destination-pattern 5000 port 2/0/0 ! dial-peer voice 6 pots destination-pattern 35.. direct-inward-dial port 1/1:1 prefix 35 ! ! line con 0 exec-timeout 0 0 privilege level 15 speed 115200 line aux 0 line vty 0 4 ! ! end Cisco 3640 Voice Gateway Controller Information 3640#SH CONTROLLER E1 1/1 E1 1/1 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20010315, FPGA: 15 Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line. Data in current interval (3 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail

Caveats • When calling from a Cisco 7960 IP phone to Nortel digital phone the Calling/Called Number is

displayed on both phones after the call is answered. • When calling from a Nortel digital phone to a Cisco 7960 IP phone, the IP phone displays calling

number after the call is answered. Nortel phone however does not get updated when the call is answered because connected number presentation is not a supported feature for E1-R2 signaling protocol. It displays the numbers being dialed instead. An example would be Access Code + extension number.

opt 11e cisco e1-r2 cas

Documents