operating & maintenance instructions -...

Document: - page 1 (Black)Screen angle and frequency: 45.0000, 150.0000

Operating & MaintenanceInstructions

Model Type Code

Month Day YearNote: General Model Series numbers noted above are inclusive of the specific mod-el number found on your engine. To get replacement parts or technical assistancein the future, write your engine Model, Type, Code and date of purchase here.

Model SeriesCovered in

This Manual

400000440000

TABLE OF CONTENTSSafety 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine Information 6. . . . . . . . . . . . . . . . . . . . . . . . Oil 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel and Starting Information 8. . . . . . . . . . . . . . . Starting and Stopping 9. . . . . . . . . . . . . . . . . . . . . . Maintenance 10-13. . . . . . . . . . . . . . . . . . . . . . . . . Adjustments 13-14. . . . . . . . . . . . . . . . . . . . . . . . . . Parts and Service & Storage 15-16. . . . . . . . . . . . Warranty Information 17. . . . . . . . . . . . . . . . . . . . .

WARNINGBriggs & Stratton does not approve or authorize the use ofthese engines on 3-wheel All Terrain Vehicles (ATVs), motorbikes, aircraft products or vehicles intended for use incompetitive events. Use of these engines in such applicationscould result in property damage, serious injury (includingparalysis), or even death.

Need assistance? Go to www.briggsandstratton.comfor detailed information regarding

Briggs & Stratton engines.Or call, 1-800-233-3723, (U.S.A. and Canada)

to hear a menu of pre-recorded messages offering engine maintenance information.

PRINTED IN U.S.A. Copyright 2003 by Briggs & Stratton Corporation FORM NO. 275475-5/03


2

Look For Relevant Emissions Durability Period andAir Index Information On Your Engine Emissions Label

Engines that are certified to meet the California Air Resources Board (CARB) Tier 2 Emission Standards must displayinformation regarding the Emissions Durability Period and the Air Index. Briggs & Stratton makes this information availableto the consumer on our emission labels.

The Emissions Durability Period describes the number of hours of actual running time for which the engine is certified tobe emissions compliant, assuming proper maintenance in accordance with the Operating & Maintenance Instructions. Thefollowing categories are used:

Moderate: Engine is certified to be emission compliant for 125 hours of actual engine running time.

Intermediate: Engine is certified to be emission compliant for 250 hours of actual engine running time.

Extended: Engine is certified to be emission compliant for 500 hours of actual engine running time.

For example, a typical walk-behind lawn mower is used 20 to 25 hours per year. Therefore, the Emissions DurabilityPeriod of an engine with an intermediate rating would equate to 10 to 12 years.

The Air Index is a calculated number describing the relative level of emissions for a specific engine family. The lower theAir Index, the cleaner the engine. This information is displayed in graphical form on the emissions label.

After July 1, 2000, Look For Emissions Compliance Period OnEngine Emissions Compliance Label

After July 1, 2000 certain Briggs & Stratton engines will be certified to meet the United States Environmental ProtectionAgency (USEPA) Phase 2 emission standards. For Phase 2 certified engines, the Emissions Compliance Period referredto on the Emissions Compliance label indicates the number of operating hours for which the engine has been shown tomeet Federal emission requirements. For engines less than 225 cc displacement, Category C = 125 hours, B = 250 hoursand A = 500 hours. For engines of 225 cc or more, Category C = 250 hours, B = 500 hours and A = 1000 hours.

The displacement of Model Series 400000 is 656 cc and 440000 engines is 725 cc.

��

The Power That Works For You.


3

BEFORE OPERATING ENGINE

• Read entire Operating & Maintenance Instructions ANDthe instructions for the equipment this engine powers.*

• Failure to follow instructions could result in serious injuryor death.

THE OPERATING & MAINTENANCE INSTRUCTIONSCONTAIN SAFETY INFORMATION TO• Make you aware of hazards associated with engines• Inform you of the risk of injury associated with those hazards, and• Tell you how to avoid or reduce the risk of injury.

275475

The safety alert symbol ( ) is used to identify safetyinformation about hazards that can result in personal injury.

A signal word (DANGER, WARNING, or CAUTION) isused with the alert symbol to indicate the likelihood and thepotential severity of injury. In addition, a hazard symbolmay be used to represent the type of hazard.

DANGER indicates a hazard which, if notavoided, will result in death or serious injury.

WARNING indicates a hazard which, if notavoided, could result in death or serious injury.

CAUTION indicates a hazard which, if notavoided, might result in minor or moderateinjury.

CAUTION, when used without the alert symbol,indicates a situation that could result in damageto the engine.

WARNINGThe engine exhaust from this prod-uct contains chemicals known to theState of California to cause cancer,birth defects, or other reproductiveharm.

HAZARD SYMBOLS AND MEANINGS

Explosion

Toxic Fumes

Moving Parts

ShockHot Surface

Kickback

Fire

THE INTERNATIONAL SYMBOLS USEDON THE ENGINE OR

IN THIS MANUAL INCLUDE:

On Off

Fuel Shutoff

Read Owner’sManual

Stop FuelChoke

Safety Alert

Oil

* Briggs & Stratton does not necessarily know what equipment this engine will power. For that reason, you should carefully readand understand the operating instructions for the equipment on which your engine is placed.


4

SAFETY

Gasoline and its vapors are extremelyflammable and explosive.

Fire or explosion can cause severe burnsor death.

WARNING

WHEN ADDING FUEL• Turn engine OFF and let engine cool at least 2

minutes before removing gas cap.• Fill fuel tank outdoors or in well-ventilated area.• Do not overfill fuel tank. Fill tank to approximately

1-1/2 inches below top of neck to allow for fuelexpansion.

• Keep gasoline away from sparks, open flames,pilot lights, heat, and other ignition sources.

• Check fuel lines, tank, cap, and fittings frequentlyfor cracks or leaks. Replace if necessary.

WHEN STARTING ENGINE• Make sure spark plug, muffler, fuel cap and air

cleaner are in place.• Do not crank engine with spark plug removed.• If fuel spills, wait until it evaporates before starting

engine.• If engine floods, set choke to OPEN/RUN position,

place throttle in FAST and crank until engine starts.

WHEN OPERATING EQUIPMENT• Do not tip engine or equipment at angle which

causes gasoline to spill.• Do not choke carburetor to stop engine.

WHEN TRANSPORTING EQUIPMENT• Transport with fuel tank EMPTY or with fuel shut-off

valve OFF.

WHEN STORING GASOLINE OR EQUIPMENTWITH FUEL IN TANK• Store away from furnaces, stoves, water heaters or

other appliances that have pilot light or otherignition source because they can ignite gasolinevapors.

Starting engine creates sparking.

Sparking can ignite nearby flammablegases.

Explosion and fire could result.

WARNING

• If there is natural or LP gas leakage in area, do notstart engine.

• Do not use pressurized starting fluids becausevapors are flammable.

WARNING

Rapid retraction of starter cord (kickback) willpull hand and arm toward engine faster thanyou can let go.

Broken bones, fractures, bruises or sprainscould result.

• When starting engine, pull cord slowly untilresistance is felt, then pull rapidly.

• Remove all external equipment/engine loadsbefore starting engine.

• Direct coupled equipment components such as,but not limited to, blades, impellors, pulleys,sprockets, etc., must be securely attached.

WARNING

Rotating parts can contact or entanglehands, feet, hair, clothing, or accessories.

Traumatic amputation or severe lacerationcan result.

• Operate equipment with guards in place.• Keep hands and feet away from rotating parts.• Tie up long hair and remove jewelry.• Do not wear loose-fitting clothing, dangling

drawstrings or items that could become caught.


5

SAFETY

Engines give off carbon monoxide, anodorless, colorless, poison gas.

Breathing carbon monoxide can causenausea, fainting or death.

WARNING

• Start and run engine outdoors.• Do not start or run engine in enclosed area, even if

doors or windows are open.

WARNING

Running engines produce heat. Engineparts, especially muffler, become extremelyhot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass,brush, etc. can catch fire.

• Allow muffler, engine cylinder and fins to coolbefore touching.

• Remove accumulated combustibles from mufflerarea and cylinder area.

• Install and maintain in working order a sparkarrester before using equipment on forest-covered,grass-covered, brush-covered unimproved land.The state of California requires this (Section 4442of the California Public Resources Code). Otherstates may have similar laws. Federal laws applyon federal land.

WARNING

Unintentional sparking can result in fire orelectric shock.

Unintentional start-up can result in en-tanglement, traumatic amputation, or lac-eration.

BEFORE PERFORMING ADJUSTMENTS ORREPAIRS• Disconnect spark plug wire and keep it away from

spark plug.• Disconnect battery at negative terminal (only

engines with electric start).

WHEN TESTING FOR SPARK• Use approved spark plug tester.• Do not check for spark with spark plug removed.

ENGINE INFORMATION

TECHNICAL INFORMATIONPOWER RATINGS: The power ratings for an individual enginemodel are initially developed by starting with SAE (Society of Auto-motive Engineers) code J1940 (Small Engine Power & TorqueRating Procedure) (Revision 2002-05). Given both the wide arrayof products on which our engines are placed, and the variety of en-vironmental issues applicable to operating the equipment, it maybe that the engine you have purchased will not develop the ratedhorsepower when used in a piece of power equipment (actual “on-site” power). This difference is due to a variety of factors including,but not limited to, the following: differences in altitude, tempera-

ture, barometric pressure, humidity, fuel, engine lubrication, maxi-mum governed engine speed, individual engine to engine variabil-ity, design of the particular piece of power equipment, the mannerin which the engine is operated, engine run-in to reduce frictionand clean out of combustion chambers, adjustments to the valvesand carburetor, and other factors. The power ratings may also beadjusted based on comparisons to other similar engines utilizedin similar applications, and will therefore not necessarily match thevalues derived using the foregoing codes.


6

ENGINE INFORMATION

2

1

4

86

6

1. Rotating screen2. Oilfill/Dipstick3. 12V electric starter4. Fuel filter (if equipped)5. Oil drain plug6. Spark plug wire7. Fuel pump8. Air cleaner

9. Intake manifold10. Choke control bracket11. Carburetor12. Throttle control bracket13. Engine Model Type Code

xxxxxx xxxx xx xxxxxxxx14. Oil filter

10

9

3

5

7

11

12

13

14

GENERAL INFORMATIONThis is a twin cylinder, overhead valve (OHV), air-cooled engine.It is a low emissions engine.

In the state of California, Model Series 400000 and 440000 en-gines are certified by the California Air Resources Board to meetemissions standards for 250 hours. Such certification does notgrant the purchaser, owner or operator of this engine any addition-al warranties with respect to the performance or operational life ofthis engine. This engine is warranted solely according to the prod-uct and emissions warranties stated elsewhere in this manual.

TUNE-UP SPECIFICATIONSArmature air gap 0.008 – 0.012 in. (0.20 – 0.30 mm). . .

Spark plug gap 0.030 in. (0.76 mm). . . . . . . . . . . . . . . . . .

Valve clearance with valve springs installed and piston 1/4 in.(6 mm) past top dead center (check when engine is cold).See Repair Manual P/N 273521.Intake 0.004 – 0.006 in. (0.10 – 0.15 mm). . . . . . . . . . . . .

Exhaust 0.004 – 0.006 in. (0.10 – 0.15 mm). . . . . . . . . . .

MODEL SERIES 400000Bore 2.97 in. (75.44 mm). . . . . . . . . . . . . . . . . . . . . . . . . . .

Stroke 2.89 in. (73.4 mm). . . . . . . . . . . . . . . . . . . . . . . . . . .

Displacement 40.0 cu. in. (656 cc). . . . . . . . . . . . . . . . . . .

MODEL SERIES 440000Bore 3.12 in. (79.25 mm). . . . . . . . . . . . . . . . . . . . . . . . . . .

Stroke 2.89 in. (73.4 mm). . . . . . . . . . . . . . . . . . . . . . . . . . .

Displacement 44.2 cu. in. (725 cc). . . . . . . . . . . . . . . . . . .

Note: For practical operation, the horsepower loading shouldnot exceed 85% of rated horsepower. Engine power willdecrease 3-1/2% for each 1,000 feet (300 meters) abovesea level and 1% for each 10° F (5.6° C) above 77° F(25° C). It will operate satisfactorily at an angle up to 15°.


7

OIL275475

CAUTION: This engine is shipped from Briggs &Stratton without oil. Check oil level before startingengine. If you start the engine without oil, the enginewill be damaged beyond repair and will not becovered under warranty.

OIL CAPACITYEngine without oil filter holds approximately 1-7/8 quarts(60 ounces; 1.8 liter).

Engine equipped with oil filter holds approximately2 quarts (64 ounces; 1.9 liters).

TYPE OF OIL TO USE• Use a high quality detergent oil classified “For Service

SF, SG, SH, SJ” or higher, such as Briggs & Stratton30W, Part Number 100005 (20 oz) or 100028 (48 oz).

• Do not use special additives.• Choose a viscosity according to the table opposite.

Note: Synthetic oil meeting ILSAC GF-2, APIcertification mark and API service symbol(shown at left) with “SJ/CF ENERGY CON-SERVING” or higher, is an acceptable oil at alltemperatures. Use of synthetic oil does notalter required oil change intervals.

°F -20 0 20 40 60 80 100

°C -30 -20 -10 0 10 20 30 40

STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

*

**

32

* CAUTION: Air cooled engines run hotter thanautomotive engines. The use of non-syntheticmulti-viscosity oils (5W-30, 10W-30, etc.) intemperatures above 40° F (4° C) will result in higherthan normal oil consumption. When using amulti-viscosity oil, check oil level more frequently.

** CAUTION: SAE 30 oil, if used below 40° F (4° C), willresult in hard starting and possible engine boredamage due to inadequate lubrication.

SAE Viscosity Grades

CHECKING AND ADDING OIL• Check oil level before starting the engine.• Check level daily, or after every eight (8) hours.

• Keep oil level at FULL.• Do not overfill.

[1] Remove oil fill cap(if equipped). Pour oil slowly.

[2] Fill to FULL line ondipstick – recheck. [3] Replace dipstick firmly.

FULL

[4] Place engine level. Cleanaround oil fill and dipstick.

[5] Remove dipstick andwipe clean with cloth.

Oil Fill

[6] Tighten dipstick down.Remove & check oil level.


8

FUEL

TYPE OF FUEL TO USE• Use clean, fresh, regular unleaded gasoline with a

minimum of 85 octane. Fresh fuel prevents gum fromforming in the fuel system or on essential carburetor parts.Purchase fuel in quantity that can be used within 30 days.

• Do not use gasoline which contains Methanol.• Do not mix oil with gasoline.• For engine protection use Briggs & Stratton Gasoline

Additive available from your Authorized Briggs &Stratton Dealer (P/N 5041 or single use pouch).

• This engine is certified to operate on gasoline. ExhaustEmission Control System: EM (Engine Modifications).

CAUTION: Some fuels, called oxygenated or reformu-lated gasoline, are gasoline blended with alcohols orethers. Excessive amounts of these blends can damagethe fuel system or cause performance problems. If anyundesirable operating symptoms occur, use gasolinewith a lower percentage of alcohol or ether.

ADDING FUEL

WARNING[1] Remove cap. Fill tank to approximately 1-1/2

inches below top of neck to allow for fuelexpansion. Be careful not to overfill.Briggs & Stratton Smart-fill� fuel can fills to thecorrect level and automatically shuts off, reduc-ing spills and emissions.

[2] Replace cap before starting.

• Turn engine OFF and let engine cool at least 2minutes before removing gas cap.

• Fill fuel tank outdoors or in well-ventilated area.• Keep gasoline away from sparks, open flames,

pilot lights, heat, and other ignition sources.• If fuel spills, wait until it evaporates before

starting engine.

STARTING

WARNING

• Do not use pressurized starting fluids.• Vapors are flammable.

OIL PRESSURE SWITCHIf engine is equipped with an oil pressure switch, the switchwill either activate a warning light or stop the engine whenthe engine runs low on oil. (Read the operating instructionssupplied by the equipment manufacturer to determinewhich way your engine is equipped because the equipmentmanufacturer supplies the oil pressure gauge.)

See OIL PRESSURE on page 11 for oil filling instructions.

STARTING AND OPERATING TIPS♦Store and fuel equipment in level position.♦Use fresh fuel. (See Fuel.)♦Use correct type of oil for expected starting

temperature. (See Oil.)♦Remove external equipment/engine loads. (See

equipment operating instructions.)♦Start lawn mower on hard surface or over previously

cut grass.

♦Periodically remove grass buildup under mowerdeck. (See Maintenance.)

♦After engine has started, let it warm up severalseconds to several minutes, depending on outsidetemperature.

♦For maximum performance and life, operate enginewith choke in RUN and throttle in FAST.


9

STARTING AND STOPPING

ELECTRIC (KEY) STARTERTO START ENGINE

[1] Check oil level (see p. 7).

[2] Open fuel shut-off valve (if equipped).

[3] Move choke control to CHOKE or START.

[4] Move throttle (if equipped) toFAST. Operate engine withthrottle in FAST.

Choke

FULL

Ï

ÏÏÏ

[5] Insert key and turn toSTART.

CAUTION: To prolongstarter life, use shortstarting cycles (5 se-conds maximum, thenwait one minute).Follow equipmentmanufacturer’s rec-ommendations forcharging battery.

[6] Let engine warm up.Choke Equipped: Movechoke control lever towardRUN a short distance at atime over several secondsin warm weather or min-utes in cold weather. Letengine run smoothly be-fore each change. Oper-ate with choke in RUN.

TO STOP ENGINE

[1] Move throttle (if equipped) to SLOW.

[2] Turn key to OFF. Remove key and store out of reach of children.[3] Close fuel shut-off valve (if equipped).


10

MAINTENANCE

MAINTENANCERegular maintenance will improve the performance andextend the life of the engine. See any Authorized Briggs &Stratton Dealer for service. Use only genuine Briggs &Stratton parts. Other parts may not perform as well,may damage the engine, and may result in injury. Inaddition, use of other parts may void your warranty.

EMISSION CONTROLMaintenance, replacement or repair of the emissioncontrol devices and systems may be performed by anynonroad engine repair establishment or individual.However, to obtain no charge repairs under the terms andprovisions of the Briggs & Stratton warranty statement, anyservice or emission control part repair or replacement mustbe performed by a factory authorized dealer.

Follow the instructions and schedules indicated below.

Task

Perform task at hourlyor calendar interval,

whichever comes first.

Eve

ry 8

Ho

urs

or

Dai

ly

25 H

ou

rs o

rE

very

Sea

son

50 H

ou

rs o

rE

very

Sea

son

100

Ho

urs

or

Eve

ry S

easo

n

Yea

rly

200

Ho

urs

or

Eve

ry S

easo

n

Check oil level �

Change oil �*

Change oil filter �

Service air cleanerpre-cleaner

�**

Replace air cleanercartridge

�**

Clean Extended LifeSeries air cleanercartridge

�**

Replace ExtendedLife Series air clean-er cartridge

�**

Inspect spark arrester(if equipped)

�

Clean cooling system �**

Replace spark plugs �

Replace in-line fuel fil-ter

�

Check valve clear-ance

�

* Change oil after first 5 to 8 hours of use, then every50 hours or every season. Change oil every 25 hourswhen operating the engine under heavy load or in hightemperatures.

** Clean more often under dusty conditions or whenairborne debris is present. Replace air cleaner parts, ifvery dirty.

CHANGING OIL

OIL DRAINPLUG

Typicaldrain plugs

PIPE3/8” SQUARE

[1] Place engine level.

[2] Disconnect spark plugwires and keep awayfrom spark plugs. Dis-connect battery (if equip-ped with electric starter)at negative terminal.

[3] With engine OFF but still warm remove oil drainplug and drain oil into appropriate receptacle.

[4] Reinstall drain plug. Remove dipstick.

[5] Fill to FULL mark on dipstick with new oil.Do not overfill.

Note: Engine without oil filter holds approximately 1-7/8quarts (60 ounces; 1.8 liters). Engine equipped with filterholds approximately 2 quarts (64 ounces; 1.9 liters).

[6] Replace dipstick.

WARNING

FULL

ÏÏÏÏ

ÏÏ

CAUTION: Used oil is a hazardous waste product.Dispose of used oil properly. Do not discard withhousehold waste. Check with your local authorities,service center, or dealer for safe disposal/recyclingfacilities.


11

MAINTENANCE

CHANGING OIL FILTERChange oil filter after every 100 hours or every season.[1] Drain engine oil and remove oil filter.[2] Before installing new filter, lightly oil filter gasket with

fresh, clean oil.[3] Screw filter on by hand until gasket contacts oil filter

adapter. Tighten 1/2 to 3/4 turn more.[4] Add fresh oil. Fill to FULL line on dipstick.[5] Start and run engine at idle to check for leaks.[6] Stop engine. Re-check oil level. Add oil if required.

OIL PRESSUREIf oil pressure drops below 4-6 psi (.2-.4 kg/cm2), an oilpressure switch (if engine is equipped) will either activate awarning light or stop the engine. Check oil level withdipstick. If oil level is between ADD and FULL mark ondipstick, Do not try to restart engine. Contact an AuthorizedBriggs & Stratton Service Dealer. Do not operate engineuntil oil pressure is corrected.

If oil level is below ADD mark on dipstick, add oil to bringlevel to FULL mark. Restart engine and check oil pressure.If pressure is normal, continue to operate engine.

Note: Oil pressure gauge, if engine is equipped, is suppliedby manufacturer of equipment.

AIR CLEANERAlways replace cartridge and pre-cleaner if damaged.

CAUTION: Do not usepressurized air or solventsto clean cartridge.

CARTRIDGE

FOAMPRE-CLEANER

Pre-cleanerTo clean, wash in liquid detergent and water. Squeeze dryin a clean cloth. Saturate with engine oil. Remove allexcess oil on pre-cleaner by squeezing inside a cleanabsorbent cloth.

REMOVING AND INSTALLING AIR CLEANER[1] See illustrations for disassembly and reassembly of

your air cleaner style.[2] Carefully remove air cleaner cartridge and pre-clean-

er to prevent debris from entering carburetor.[3] Install pre-cleaner in base with mesh side up.[4] Install cartridge on pre-cleaner.[5] Replace cover. To ensure proper fit, tabs must be

hooked into slots. Tabs are painted a different color insome instances.

[6] Latch handle or tighten knobs completely to securecover.

CAUTION: Improper installation of air cleanercover may cause damage to engine.

EXTENDED LIFE SERIES� CARTRIDGE ONLY

This filter, IF STAMPED ‘WASHABLE’, can be washedwith warm water and mild soap. IMPORTANT: Rinse intap water with SCREENside up allowing dirt anddebris to filter out. Leavefilter to dry overnight be-fore reinstalling.


12

MAINTENANCE

ENGINE AND ENGINE PARTSWe recommend that you see an authorized Briggs & Stratton Service Dealer for all maintenance and service of the engineand engine parts. Use only genuine Briggs & Stratton parts.

WARNINGIf you perform any maintenance on the engine, first disconnect the spark plug wiresfrom the spark plugs, and disconnect the battery at the negative terminal (electricstarter engines only) to prevent unintentional sparking. Unintentional sparking canresult in fire or electric shock. Unintentional start-up can result in entanglement,traumatic amputation or laceration. Use only correct tools.

WARNING• Do not strike the flywheel with a hammer or hard object because the flywheel may

later shatter during operation.• Do not tamper with governor spring, links or other parts to increase engine speed.

MUFFLERReplacement parts for themuffler must be the same andinstalled in the same positionas the original parts, other-wise fire can occur.If muffler is equipped with sparkarrestor screen, remove

screen for inspection. Replace screen if damaged or plugged.

WARNING

FUEL SYSTEMReplacement parts for fuelsystem (cap, hoses, tanks,filters, etc.) must be the sameas original parts, otherwisefire can occur.

WARNING

FUEL FILTER (if equipped)

[1] Disconnect spark plugwires and keep awayfrom spark plugs.

[2] Drain fuel tank or closefuel shut-off valve beforereplacing fuel filter.Otherwise, fuel can leakout, creating a fire/explo-sion hazard.

ÎÎÎÎ ÎÎ

ÎÎÎÎÎÎÎÎ

ÎÎÎ

FILTER

WARNING

AIR COOLING SYSTEMDebris may clog the engine’s air cooling system. Removeblower housing and clean area shown to prevent overheat-ing and engine damage.

SCREWS

AIR CLEANERKNOBS

CLEAN AREAS UNDERBLOWER HOUSING

OF ALL DEBRIS

CARBURETORAIR INTAKE

SPARK PLUGUse only Briggs & Stratton Spark Tester (part number19368) to check for spark.Note: In some areas, locallaw requires using resistorspark plug to suppress igni-tion signals. If this enginewas originally equipped withresistor spark plug, usesame type for replacement.

.030” (0.76 mm)WIRE GAGE

VALVE CLEARANCECheck valve clearance yearly. (See Tune-up Specificationson page 6).


13

MAINTENANCE

CLEANING DEBRIS

CAUTION: Do not use water to clean engine parts.Water could contaminate fuel system. Use a brushor dry cloth.

Engine parts should be keptclean to reduce the risk ofoverheating and ignition ofaccumulated debris. This isespecially important if cutting

tall grass. Daily or before every use, clean accumulateddebris from engine.

WARNING

Keep linkage, springs and controls clean.

Keep area around and behind muffler free of any combus-tible debris.

Keep muffler area clean and muffler in working order. Dailyor more often, before running engine, clean muffler area toremove all grass and combustible debris. If engine muffleris equipped with spark arrester screen, remove for cleaningand inspection. Replace if damaged or plugged.

Rotating Screen

ROTATING SCREEN

Linkage, Springs and Controls

CLEAN

ADJUSTMENTS

CONTROL ADJUSTMENTS

WARNING

Prevent unintentional starting.

Before performing adjustments:

• Remove spark plug wires from spark plugs.• Disconnect battery at negative terminal (only

engines with electric start).

TO ADJUST REMOTE CHOKE CONTROL

CASING CLAMP SCREW

PULL TO CHOKE

WIRE ANDCASING

[1] Remove air cleaner.

[2] Move choke control to CHOKE or START position.(Carburetor choke should be completely closed.)

[3] If not, loosen casing clamp screw.

[4] Then move casing, wire and engine choke lever indirection shown until choke is completely closed.

[5] Tighten casing clamp screw. Replace air cleaner.


14

ADJUSTMENTS

TO ADJUST REMOTE THROTTLE CONTROL

If the engine does not start or if it runs roughly, the remotethrottle control may need adjustment. See your authorizedBriggs & Stratton dealer or follow the instructions below.

[1] Move throttle control to FAST. (Swivel should beagainst throttle stop.)

[2] If not, loosen casing clamp screw. Move casingand wire in direction shown by arrow until swivel isagainst throttle stop.

[3] Tighten casing clamp screw.

CASINGCLAMPSCREW

SWIVEL

THROTTLESTOP

CARBURETOR ADJUSTMENT

WARNING

The manufacturer of the equipment on which thisengine is installed specifies top speed at which theengine will be operated. DO NOT EXCEED this speed.

Differences in fuel, temperature, altitude or load mayrequire minor carburetor adjustment. Air cleaner and aircleaner cover must be assembled to carburetor beforestarting engine.

The carburetor on this engine is low emission. It is notadjustable except for idle speed. Governed idle speedis1750 rpm, set at the factory.

TO ADJUST CARBURETOR

IDLESPEEDSCREW

CARBURETORTHROTTLE

LEVER

Double Barrel

IDLESPEEDSCREW

CARBURETORTHROTTLE

LEVER

Single Barrel

[1] Start engine and warm up approximately 5 minutesbefore adjusting.

[2] With engine running, place throttle control in SLOWposition.

[3] Rotate carburetor throttle lever against the idle speedscrew and hold it.

[4] Turn idle speed screw to obtain 1500 rpm.

[5] Release carburetor throttle lever. Move throttle controlto FAST position. Engine should accelerate smoothly.

Note: Engines operated at about 3000 feet (900 meters) orhigher above sea level may require a high altitude carbure-tor main jet. If erratic performance is observed, contact aBriggs & Stratton Authorized Service Dealer for cost toinstall/purchase a high altitude carburetor main jet.


��

�� !"��#$��#%��

#&� �''��%

"�(��&

)��%��*��'��

��+��+

$��

Pay

men

t M

eth

od

:Fi

ll in

bot

h si

des

of th

is o

rder

form

car

eful

ly

�C

heck

or

mon

ey o

rder

enc

lose

d pa

yabl

e to

Bri

gg

s &

Str

atto

n C

orp

ora

tio

nin

the

amou

nt o

f $__

____

_(U

.S. D

olla

rs, p

leas

e)

�P

leas

e ch

arge

my

�M

aste

rCar

d�

VIS

A

CR

ED

IT C

AR

D N

UM

BE

R

SIG

NA

TU

RE

(R

EQ

UIR

ED

FO

R C

RE

DIT

CA

RD

OR

DE

RS

)E

XP

IRA

TIO

N D

AT

E

Par

ts L

ist

Sh

ipp

ing

& H

and

ling

**A

dd

Sta

te S

ales

Tax

Tota

l

$2.0

0$1

.50

To p

urch

ase

a co

mpl

ete

list o

f Gen

uine

Brig

gs &

Str

atto

n P

arts

for

your

eng

ine,

fill

inbo

th s

ides

of t

his

orde

r fo

rm c

aref

ully

. W

e ca

nnot

fill

your

ord

er w

ithou

t the

cor

rect

Eng

ine

Mod

el/T

ype/

Cod

e. A

llow

3 to

4 w

eeks

for

deliv

ery.

15

SERVICE & STORAGE

PARTIAL LIST OF GENUINE BRIGGS &STRATTON PARTS

BRIGGS & STRATTONPART PART NO. (or equivalent)Extended Life Series air cleaner cartridge 695667Air cleaner cartridge 499486Air cleaner pre-cleaner 273638Oil 100005 -or- 100028Extended Life Series oil filter 696854Oil filter 492932 -or- 5049Fuel filter (2.75” length) 691035Fuel filter (3.5’ length) 695666Gas additive 5041Resistor spark plug (Champion RC12YC) 491055Static suppression spark plug (Champion QC12YC) 691043Long life platinum spark plug 696202 -or- 5066Spark plug wrench 19374Spark tester 19368Oil pump kit 5056(uses standard electric drill to remove oil from engine quickly)

SERVICESee an Authorized Briggs & Stratton Service Dealer. Eachone carries a stock of Genuine Briggs & Stratton Parts andis equipped with special service tools. Trained mechanicsassure expert repair service on all Briggs & Strattonengines. Only dealers advertising as “Authorized Briggs &Stratton” are required to meet Briggs & Stratton standards.

When you purchase equipment powered by aBriggs & Stratton engine, you are assured ofhighly skilled, reliable service at more than30,000 Authorized Service Dealersworldwide, including more than 5,000 MasterService Technicians. Look for these signswherever Briggs & Stratton service is offered.

You may locate your nearest Authorized Briggs & StrattonService Dealer in our dealer locator map on our web site�� or in the “Yellow Pages”

directory under “Engines, Gasoline” or “GasolineEngines,” or “Lawn Mowers” or similar category.

Note: Walking fingers logo and “Yellow Pages” are regis-tered trademarks in various jurisdictions.

An illustrated shop manual includescommon specifications and detailed in-formation covering adjustment, tune-upand repair of Briggs & Stratton twincylinder, OHV, 4 cycle engines. It isavailable for purchase from an Autho-rized Briggs & Stratton Service Dealer oryou can order it from the factory. Write:Briggs & Stratton CorporationAttn: Service DivisionP. O. Box 1144Milwaukee, WI 53201

Part No. 273521


16

SERVICE & STORAGE

STORAGEEngines stored over 30 days need special attention.

[1] To prevent gum from forming in fuel system or onessential carburetor parts:a) if fuel tank contains oxygenated or reformulatedgasoline (gasoline blended with an alcohol or anether), run engine until it stops from lack of fuel, or b) iffuel tank contains gasoline, either run engine until itstops from lack of fuel, or add a gasoline additive to thegas in the tank. (See parts list. Single – use pouches ofgas additive are available from your service dealer.) Ifyou use a gas additive, run the engine for severalminutes to circulate the additive through the carburetor.Then, engine and fuel can be stored up to 24 months.

You

r E

ng

ine

Typ

eC

od

eM

od

el

Fill

in b

oth

side

s, c

lip a

nd r

etur

n to

:B

rig

gs

& S

trat

ton

Co

rpo

rati

on

P.O

. Bo

x 11

44

Nam

e

Ad

dre

ss

Cit

yS

tate

Zip

Co

un

try

To p

urch

ase

a co

mpl

ete

list o

f Gen

uine

Brig

gs &

Str

atto

n P

arts

for

your

eng

ine,

fill

inbo

th s

ides

of t

his

orde

r fo

rm c

aref

ully

. W

e ca

nnot

fill

your

ord

er w

ithou

t the

cor

rect

Eng

ine

Mod

el/T

ype/

Cod

e. A

llow

3 to

4 w

eeks

for

deliv

ery.

Milw

auke

e, W

I 532

01–1

144

U.S

.A.

[2] While engine is still warm, change oil.

[3] Remove spark plugs and pour about 1 oz. (30 ml) ofengine oil into each cylinder. Replace spark plugs andcrank slowly to distribute oil.

[4] Clean engine of surface debris, chaff or grass.

WARNING[5] Store in a clean, dry area.

Do not store in same areaas a stove, furnace, waterheater, or other appliancethat uses a pilot light orhas a device that cancreate a spark.

Engwnty1-03 - page 1 (Black)Screen angle and frequency: 45.0000, 150.0000

17

��

��

LIMITED WARRANTYBriggs & Stratton Corporation will repair or replace, free of charge, any part(s) of the engine that is defective in material or workmanship or both.Transportation charges on parts submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for thetime periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator mapat www.briggsandstratton.com, or by calling 1-800-233-3723, or as listed in the ‘Yellow Pages’.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR APARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLIEDWARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENTEXCLUSION IS PERMITTED BY LAW. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states orcountries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you.This warranty gives you specific legal rights and you may also have other rights which vary from state to state and country to country.

��

��

��

�� (Sleeve Bore)

�!��"��

�� (Kool Bore)�!#�� $�

%��&�

%��!�

%45��'��

��"�

Commercial Use2 years

90 days1 year

Consumer Use 2 years 2 years

90 days

1 year

(� ��)(��

�� )*

��

1 year

* Note the following special warranty periods: 2 years for Classic engines in the European Union and Eastern European countries, for all consumer products inthe European Union, and for emission control systems on engines certified by EPA and CARB. 5 years for consumer use, 90 days for commercial use of Touch-N-Mow starter on Quantum and Intek engines. Engines used in competitive racing or on commercial or rental tracks are not warrantied.

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in the tableabove. “Consumer use” means personal residential household use by a retail consumer. “Commercial use” means all other uses, including use for commercial,income producing or rental purposes. Once an engine has experienced commercial use, it shall thereafter be considered as a commercial use engine for pur-poses of this warranty.

NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF PURCHASERECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED, THEMANUFACTURING DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.

�� !� "�� #� �� $� �� # �� !�� $� �� !�� %�� & �� '�� # �� (�� "�� &� �� #��

�� !�� "�� #�� $��!�� !� �%�� !��! �!� �"�� &�� !� �� '�� %�� )� *+,�-'�� .�/�'� �0 *�+&� &1�& �+' 2,&

,+$3$2�- �+$33� � �&+�&&,2 *�+&��4� '��

�� 5.�� 6

7� - #�� #�� 5/� �� 8�� !� � �� *�� 2� 9:;)�6

;� *�� # � � �� 5�� # �� <=�� + �� 6 ,$- 3�+� �� '�� + � ,� �� $��

9� + �� %��

>� �� 8�� 8�� 5��

�� 8�� ,��8!� � � �� 8�� 6 + �,� �� $��

?� *�� 8�� 5.� � �� 6 + � ,� �� $��

<� '�� # � �� "� �� #�� 8��

@� � � �� # � ��#�� #�� % �� "� �� 8� ��

):� +�� 8�� %�� ))� '��

��

�� !��"! �� !��!!�� !��(�� )��""� * +�� ,��& �� -��!��(�� +�� .�� !�/0�� 1"��2 �� !�� /�"�� 3��2 �� /3�� "��2 /4�5��2 �� "�� &

��(� (� ��

Engwnty1-03 - page 2 (Black)Screen angle and frequency: 45.0000, 150.0000

18

�� !� �!�'!��!� +��,- �.� ��/!�� !��"�� !�� +��,�� .� (�� 0��!�&�� !��"��!� ��"1 +(2�2 ��,

�&��!� �!��!� �1��& ��1 ��&�� +#��3� )�/�"� ��1 ��.�� 4��!��,

EMISSION CONTROL WARRANTY COVERAGE IS APPLICABLE TO CERTIFIED ENGINES PURCHASED IN CALIFORNIA IN 1995 AND THERE-AFTER, WHICH ARE USED IN CALIFORNIA, AND TO CERTIFIED MODEL YEAR 1997 AND LATER ENGINES WHICH ARE PURCHASED ANDUSED ELSEWHERE IN THE UNITED STATES (AND AFTER JANUARY 1, 2001 IN CANADA).

��/!�� (�� &��!� �!��!� )�/�"�� 1 ��&��

The California Air Resources Board (CARB), U.S.EPA and B&S are pleased to explain the EmissionControl System Warranty on your model year2002 and later small off-road engine (SORE). InCalifornia, new small off-road engines must be de-signed, built and equipped to meet the State’sstringent anti-smog standards.

Elsewhere in the United States, new non-road,spark-ignition engines certified for model year1997 and later must meet similar standards setforth by the U.S. EPA. B&S must warrant the emis-sion control system on your engine for the periodsof time listed below, provided there has been noabuse, neglect or improper maintenance of yoursmall off-road engine.

Your emission control system includes partssuch as the carburetor, air cleaner, ignition sys-tem, muffler and catalytic converter. Also in-cluded may be connectors and other emissionrelated assemblies.Where a warrantable condition exists, B&S willrepair your small off-road engine at no cost toyou including diagnosis, parts and labor.

�� !� �&��!� �!��!� )�/�"�� 1 �!0��

Small off-road engines are warranted relative to emission control parts defects for a period of two years, subject to provisions set forth below. If anycovered part on your engine is defective, the part will be repaired or replaced by B&S.

#��3� ��1 ��'!��4��

As the small off-road engine owner, you are re-sponsible for the performance of the requiredmaintenance listed in your Operating and Main-tenance Instructions. B&S recommends thatyou retain all your receipts covering mainte-nance on your small off-road engine, but B&Scannot deny warranty solely for the lack of re-ceipts or for your failure to ensure the perfor-mance of all scheduled maintenance.

As the small off-road engine owner, you shouldhowever be aware that B&S may deny you war-ranty coverage if your small off-road engine or apart has failed due to abuse, neglect, impropermaintenance or unapproved modifications.You are responsible for presenting your smalloff-road engine to an Authorized B&S ServiceDealer as soon as a problem exists.

The undisputed warranty repairs should becompleted in a reasonable amount of time, notto exceed 30 days.If you have any questions regarding your war-ranty rights and responsibilities, you should con-tact a B&S Service Representative at1-414-259-5262.The emission warranty is a defects warranty.Defects are judged on normal engine perfor-mance. The warranty is not related to an in-useemission test.

�� !� �&��!� �!��!� )�/�"�� 1 ��!0��!��

The following are specific provisions relative to your Emission Control Defects Warranty Coverage. It is in addition to the B&S engine warranty for non-regulated engines found in the Operating and Maintenance Instructions.1. Warranted Parts

Coverage under this warranty extends onlyto the parts listed below (the emission con-trol systems parts) to the extent these partswere present on the engine purchased.a. Fuel Metering System

• Cold start enrichment system• Carburetor and internal parts• Fuel Pump

b. Air Induction System• Air cleaner• Intake manifold

c. Ignition System• Spark plug(s)• Magneto ignition system

d. Catalyst System• Catalytic converter• Exhaust manifold• Air injection system, Pulse valve

e. Miscellaneous Items• Vacuum, temperature, position,

time sensitive valvesand switches

• Connectors and assemblies

2. Length of CoverageB&S warrants to the initial owner and eachsubsequent purchaser that the WarrantedParts shall be free from defects in materialsand workmanship which caused the failureof the Warranted Parts for a period of twoyears from the date the engine is delivered toa retail purchaser.

3. No ChargeRepair or replacement of any WarrantedPart will be performed at no charge to theowner, including diagnostic labor whichleads to the determination that a WarrantedPart is defective, if the diagnostic work isperformed at an Authorized B&S ServiceDealer. For emissions warranty servicecontact your nearest Authorized B&S Ser-vice Dealer as listed in the “Yellow Pages”under “Engines, Gasoline,” “Gasoline En-gines,” “Lawn Mowers,” or similar category.

4. Claims and Coverage ExclusionsWarranty claims shall be filed in accordancewith the provisions of the B&S Engine War-ranty Policy. Warranty coverage shall be ex-cluded for failures of Warranted Parts whichare not original B&S parts or because ofabuse, neglect or improper maintenance as

set forth in the B&S Engine Warranty Policy.B&S is not liable to cover failures of War-ranted Parts caused by the use of add-on,non-original, or modified parts.

5. MaintenanceAny Warranted Part which is not scheduledfor replacement as required maintenance orwhich is scheduled only for regular inspec-tion to the effect of “repair or replace as nec-essary” shall be warranted as to defects forthe warranty period. Any Warranted Partwhich is scheduled for replacement as re-quired maintenance shall be warranted as todefects only for the period of time up to thefirst scheduled replacement for that part. Anyreplacement part that is equivalent in perfor-mance and durability may be used in the per-formance of any maintenance or repairs.The owner is responsible for the perfor-mance of all required maintenance, as de-fined in the B&S Operating and MaintenanceInstructions.

6. Consequential CoverageCoverage hereunder shall extend to the fail-ure of any engine components caused bythe failure of any Warranted Part still underwarranty.

�� '�� /�� ,� ,� �� ,� &� !�� *� ��A � �� 84;?�)?? 5,�� *� �� * ��6

6,325,0366,284,1236,260,5296,230,6786,202,6166,116,212

6,077,0636,064,0276,014,8085,894,7155,852,9515,823,153

5,819,5135,813,3845,765,7135,645,0255,642,7015,619,845

5,606,9485,606,8515,548,9555,546,9015,503,1255,501,203

5,497,6795,320,7955,271,3635,269,7135,265,7005,243,878

5,235,9435,197,4255,197,4225,191,8645,188,0695,186,142

5,138,9965,086,8905,070,8295,058,5445,040,6445,009,208

4,996,9564,977,8794,971,2194,895,1194,819,5934,719,682

4,633,5564,630,4984,522,0804,520,2884,512,4994,453,507

4,430,984 DES. 308,871DES. 308,872DES. 309,457DES. 356,951DES. 361,771DES. 375,963


��

��

!�� "��#�� $%�&�� !�� %��%�� '�� %�� !� "#�$�%%�!�� %%��&�� !'��(�#� ��$��#� �� ('�� )**+ �� #�� ,�� -�� '�� .��#� �� ('��/ �� -��0 !'"�� (�#� "� )**1 �� #�� .

,�� -�� '�� #�# ��$��#� �� #� �� 0 �� %�#� �� )��2��,�� 344) �� "��5

(%�� "��#�� $%�&�� 6�� 7� &�� &�/ �� &�� 89��7�� 7�� :��8��5�5 �%�� &; � �� <��= ��=�� >�?8� �97<��8�� 8�� <�� :�� 8��?�� 3444 �� 9� ��9�� '��5 �� 6��/ ��:��= �� 8�� <�� :�� @�� 7��A�/ 7�� 9 ��9 �� 7�� = ��5 �� = ��/ �� :��= 8�� <�� BC�� 8�� 7��6�9 �� 8��?�� )**1 �� / ��:�� 7�� 8� �8�.�� 8�� :�� 5�5 �%�5 &�� ; �� >�?8� �� 7��D�� 97<��.

��8�� :�� 8�� 9�� 8� 8��9� 7��7��/ ��6 �� 6�� CE��C�/ �� 9��7� �� 95,�� >�?8� �� 7��D�� 97<��8�� 7�8�� ?7� �� 7��C��/ �� 6�� B��/ �� >�?8� ��/ �� 7��= �� 7��:�� 7��>�� 5 �� 7�8�� 7��7�� ?7� ��9� B �98��5�� > � 7�� B ��/ &;� �9�� 8�� :�� 8�� <�� 7�� 7/ �� ?7� �� 8�� F�:��5

�� %��% �� "��#�� )�� $%�&�� 8�� <�� 7�� 96�7��9 �� ?7� �� >�?8� �� 7��D.�� 97<��8�� 9�� 3 ��/ �E�� = 7�� 9� 7��7��5 �� 8��.

�� ?7� �� :�� 8�� 7��:�� 7�� 96�7��/ �� 9��9� ��8��79� �� &;�5

��'��%� �� %�� 9�� 8�� <�� / :�� @�� C�� :�� B ��=97�� 9 �� :�� 8�� 9�� 5 &;� :�� 7�8.8�� 7��:�� A� 7��:�� :��= �� :�� 8�� <�� .��/ 8�� &;� �� 6�� C��7� �� A� �� 96�� :�� :�� 97<9��7�� 88� ��5�� 9�� 8�� <�� / :�� :�G @�� 6��89 �� &;� �� 6��<�� 7�� 96�7��9 �� :�� 8�� :�� 8�� B�� 8�� C��6/ �� 9��7�/ �� 7��7� �� 8��6�7�� :9�5

,�� :�G �� C��9 �� :�� 8�� <�� B �� 9�� 9 &;��D� �� :�� C�?8�5 �� 9�� :�� @�� 7�8��9�9� �� 9�� C�� :�� =79�� H4 E��5�� :�� :�G �� :�8�� B :�� / :� �� C��9/ :��G7�88�� :�7 �� 9�� :�7� &;� �� 89�� )�I)I�3+*�+3J35�� >�?8� �97<��8�� 7�� 96�7��95 �� 96�7��.�9 �� E��9� �� 6��7�� 8�� 8��5 �� 9� B �� 97<��8�� 66�7��9 B ��9��5

(�� "��#�� $%�&�� 7��7�� 97�6� �� :�8�� B :�� >�?8� �� 7��D�� 97<��8��5 �� B �� &;� �� 8�� 9��8��9 7�� 8�� 5)5 ��#��

�� 7��:�� 7�� ?7� ��9� 7��7�� >�?8� �� 7��D�� 97<��8�� 8�� K 7� ��?7� 9�� 9�� 8�� 8�8�� 7<��5�5 �>�?8� �� 7��C��

• �>�?8� ��7<��8�� 98�� B 6��• ��C�� • %�8�� B ��7�

C5 �>�?8� ��7�� • (�� B ��• ��C�� 8��

75 �>�?8� ��• &�� 8��• �>�?8� ��8�� 9��7��8��9��

�5 �>�?8� 7��>��• ��:�� 7��>�� • ��7�� 97<��8��• �>�?8� ��E�7�� B ��

�5 �� ?7� ��9� �� >�?8� 7��<�� 8��9• �� 9��/ �� 8�9��/ �� 5• ��7�� 8C��5

35 (��%� �� &;� �� 9�� 7<�� C9 �� ?7� �� .�� =�8�� :�7� �� 8��?�� 6�C��7�� 7�� 96�7��.�9 �� ?7� �� 9�� = �� B �� B �� 8�.�� 9�9 ��:�9 B ��7<��5

H5 ��7�� (�� 9�� 8��7�8�� ?7� �� 66�7��9� �� 7��6�� 9��/ ��7�� 6�� 8�� F�:�� 7 �6�� 9��8�.�� ?7� �� 96�7��/ 7�� B 7� �� 7 �� 66�7��97<�G �� 9�� 9 &;�5 %�� :� �� >�?8� �97<��8��/ 7�88�.�� G �:�7 �� 9�� 9 &;� �� 7<� �� 9 �� E�� :�� 7��9 �� C�� 8�� B ��7�/ �� 7��9�� 8��5

I5 �97��8�� =7�� 7��:��5�� 97��8�� :�� @�� 7�8��9�9� �� 77�� :�7 �� &;�5 �� 7��:�� 96�7��9 �� ?7� �� ?7� �� &;� �� 7� ��C�/ �9��7� �� 95�� &;� �� 7��:�� 96�7��9 �� ?7� �� 6�� CE��E��/ �� 9�9 8��6�9� �� ?7� �� ?7� &;� ��5

+5 �� ?7� �� 8��79� �� 8�8�� 8�� .�� 6�9� ��8�� 7�� 9��?�� 8�� LM�9�� 8��7�� 97��MN �� 7�� 96�7��9 �� 9�� 5�� ?7� �� 6�9� �� 8��7�8�� .�� 7�� 96�7��9 ��8�� 9�� 8� �� :� E� ��8�� 8��7�8�� 9:� �� 7�� ?7�5 �� ?7� �� 8��7�8�� 9 ��:�� 6��8��7� �� C��9 �� @�� 9� �� 9��5 �� 9�� C�� =97�� 96�� 8�� 7��&;� �� 9��5

J5 ��:�� 7�� 7��:�� 7��7�� 9�� B �� 96�7��9 �� 7�8�� 8�� 7��9� �� 96�7��9 �� 8�� ?7� 7��:�� 7�� :��5

��* �� %�� '��% �$%�� $+,(+�� $�� $%��-�� $%�� 8�� 7��6�9 7��6��8� ��= ��8� �� 98�� 6�� 7� &�� &� �� 3/ ��:�� 66�7<�� 6��8�� 7��7�� 9�� C��9 �� >�?8��98�� "�� 5 �� 6��8�� 9� �� 9�� 9� �� 8�� &�� ; ��5 �9�� 8�� 8�� 7��7�� 7��6�7��5�� %�� '��% �$%�� 8C�� <�� 8�� 8�� 7��6�9 7��6��8� ��= ��8� �98�� 9��:� �� 9 �� 9 �� 8�� 9�� 5 �� 7��9�� :�� 9�MO.��%�% �� 8�� 7��6�9 7��6��8� �� )3+ <�� 8��5+��%�� 8�� 7��6�9 7��6��8� �� 3+4 <�� 8��5��% �� 8�� 7��6�9 7��6��8� �� +44 <�� 8��5%�� =�8��/ �� 8��?�� 9� ��:�� 34 B 3+ <�� 9�5 %�� 7��9 ��/ �� %�� '��% �$%�� 8�� 7��9�� 89�� 7� �>�� 9 ��:�� B )4 B )3 ��5�� $�� 8C�� 97�� :�� 6 �98�� 7��9�� 97�6� �� 8��5 %�� $�� C�/ �� 8�� 97�� 5 �� 6��8�� 9� �� 6��8� ��<� �� 9�� 98��5

/ �� 0�� 1�� 2333� ��* �� %�� % �$%�� %��-��? �� )�� E�� 3444/ 7�� 8�� &;� �� 7��6�9 7��6��8� ��= ��8� ��:��8�� 98�� :��8�� %��7�� 7> �� %�� %<�� 35 %�� 8�� 7��6�9 �� %<�� 3/ �� 9�� 7��6��8��9 �98�� 8��9� �� 9�� 8C�� <�� 8�� 7�� 8� 69�9��5 %�� 8�� 6��7� 8�� 33+ 77/ �� 7��9�� P )3+ <��/ & P 3+4 <�� P +44 <��5 %�� 8�� 33+ 77 �� / �� 7��9�� P 3+4 <��/ & P +44 <�� P )444 <��5�� 8��7�8�� 8�� 8��?�� 9�� I44444 �� J+J 775 �� 8��7�8�� 8�� 8��?�� 9�� II4444 �� 13+ 775

�� %�� %��-�� $%��

-�� * �� %�4OCE MOTEUR EST CONFORME AUX NORMES

ANTIPOLLUTION 2000 – 2001 DE CALIFORNIEPOUR LES PETITS MOTEURS HORS ROUTE ET

AUX NORMES ENVIRONNEMENTALESAMÉRICAINES (EPA PHASE 2) POUR LES

PETITS MOTEURS HORS ROUTE. CONSULTEZ LE MANUEL DU PROPRIÉTAIRE POUR LES

SPÉCIFICATIONS, L’ENTRETIEN ET LES AJUSTEMENTS. CONFORME À LA PÉRIODE

D’ÉMISSION EPA : CATÉGORIE : C

FAMILLE YBSXS.3192VA 274812

INFORMATIONS IMPORTANTESCORPORATION BRIGGS & STRATTON

operating & maintenance instructions -...

Documents