operating instructions bpc-tool englisch · bpc-toolis connected directly to the battery by the...

.

BD0054V0004EN0416S0 460 988-17 / 04.16

Operating instructions en

BPC-Tool

Inhaltsverzeichnis BPC-Tool

Table of Contents

1 Safety precautions .........................................................................51.1 General Safety Precautions ...........................................................5

1.2 Safety precautions for the BPC-Tool..............................................5

1.3 Safety precautions for battery maintenance ..................................6

1.4 Safety Precautions Regarding the Risk of Injury ............................6

1.5 Safety precautions regarding chemical burns ................................6

2 Product descriptions......................................................................72.1 Intended use .................................................................................7

2.2 Notes for using the Bluetooth function...........................................7

2.3 Delivery Contents..........................................................................8

2.4 Top ...............................................................................................9

2.5 Connectors..................................................................................10

2.6 Power supply ..............................................................................10

3 Putting the BPC-Tool into operation ......................................133.1 Switching on the BPC-Tool ..........................................................13

3.2 Switching off the BPC-Tool..........................................................13

4 Configuring the BPC-Tool ..........................................................144.1 Configuring the time zone ...........................................................14

4.2 Setting the Time Format .............................................................14

4.3 Configuring summer time............................................................14

4.4 Setting the Date Format ..............................................................14

4.5 Configuring the language ............................................................15

4.6 Configuring the temperature units...............................................15

2

BPC-Tool Inhaltsverzeichnis

4.7 Configuring the decimal separator...............................................15

4.8 Configuring the display contrast ..................................................16

4.9 Standby time...............................................................................16

4.10 Configuring instructions ..............................................................16

5 Service .............................................................................................175.1 Calling up product information ....................................................17

5.2 Calling up self-test......................................................................17

5.3 Calling up memory information ...................................................18

5.4 Performing a factory reset ..........................................................18

6 Working with the BPC-Tool via a diagnostic tool...............196.1 Preconditions for connecting the BPC-Tool..................................19

6.2 Connection to the diagnostic tool .................................................19

7 Working with the BPC-Tool.......................................................207.1 Symbols......................................................................................20

7.2 Connecting the BPC-Tool to the battery.......................................20

7.3 Performing a battery test ............................................................22

7.4 Performing a start/stop test ........................................................23

7.5 Performing a system test ............................................................24

7.6 Reports.......................................................................................26

8 BPC client App ...............................................................................288.1 Installation..................................................................................28

8.2 Putting the BPC client App into operation ....................................30

8.3 Configuring the BPC client App....................................................31

8.4 Working with the BPC client App .................................................32

3

Inhaltsverzeichnis BPC-Tool

9 General information.....................................................................399.1 Problem solutions .......................................................................39

9.2 Care and maintenance.................................................................39

9.3 Disposal ......................................................................................39

9.4 BPC-Tool technical data ..............................................................40

4

BPC-Tool Safety precautionsGeneral Safety Precautions

1 Safety precautions

1.1 General Safety Precautions

• The BPC-Tool is exclusively intended for use on a vehicle. It is a precondition for the use of the BPC-Tool that the user has knowledge of automotive engineering and is therefore aware of the sources of danger and risks in the workshop and on the vehicle.

• All notes given in the individual sections of the operating instructions apply. In principle it is required to follow the steps and safety precautions stated below.

• Furthermore, pay attention to all general instructions from labour inspectorates, trade associations and vehicle manufacturers as well as all laws, legal ordinances and instructions which have to be commonly obeyed by a repair shop.

1.2 Safety precautions for the BPC-Tool

In order to avoid incorrect handling and resulting injury to the user or destruction of the BPC-Tool, observe the following:

• Use the BPC-Tool exclusively for the purpose of testing batteries (12 V).

• Protect the BPC-Tool from long periods of exposure to solar radiation.

• Protect the BPC-Tool from water (it is not waterproof).• Protect the BPC-Tool from strong impacts (do not drop).

5

Safety precautions BPC-ToolSafety precautions for battery maintenance

1.3 Safety precautions for battery maintenance

When working on batteries, there is a risk of injury due to faulty or damaged batteries. Therefore regard the following:

• Do not smoke or generate any sparks or open flames in the vicinity of batteries.

• Remove any items of jewellery and watches.• In order to prevent sparks or short circuits, avoid the use

of metal tools where possible.

1.4 Safety Precautions Regarding the Risk of Injury

When working on the vehicle, there is a risk of injury through inadvertent rolling of the vehicle. Therefore regard the following:

• Make connections to the vehicle only when engine is not running.

• Additionally place selector lever of automatic transmission vehicles to P position.

• Protect vehicle against rolling away.

1.5 Safety precautions regarding chemical burns

If the battery is damaged, there is a danger of chemical burns due to the escape of battery acid. Therefore regard the following:

• Immediately rinse affected parts of the body or clothing with water(consult a doctor!).

• Seek medical attention immediately on inhaling or swallowing.

• If battery acid comes into contact with eyes, rinse eyes with running water for at least 15 minutes and immediately consult a doctor.

• Wear appropriate safety googles and a face mask.

6

BPC-Tool Product descriptionsIntended use

2 Product descriptions

2.1 Intended use

The Battery Power Check Tool (BPC-Tool) is a mobile tool for checking batteries up to 12 V of all common types and from all standard manufacturers. The BPC-Tool is connected directly to the battery by the battery connecting cable. The Bluetooth wireless connection to some Hella Gutmann diagnostic tools enables the measured data to be transferred to the Car History. In addition, the battery test can also be carried out using the diagnostic tool.

You can couple the BPC-Tool to the PC via Bluetooth using the BPC client App. The BPC client App is a piece of software that can be installed on Windows-based PCs. As a result, the battery tests and system tests can be printed out without the diagnostic tool. You can download the BPC client App for free from the Hella Gutmann homepage.

The BPC client App can exclusively be used on PCs, laptops and tablets and is not suitable for smartphones.

The BPC-Tool can only be connected to certain Hella Gutmann diagnostic tools. Diagnostic tools from other manufacturers are not supported.

The BPC-Tool cannot be used to check high-voltage battery modules in hybrid or electric vehicles.

2.2 Notes for using the Bluetooth function

The terms of use of the Bluetooth function may be restricted or prohibited through law or corresponding legal regulations in certain countries.

Observe the provisions in force in the respective country before using the Bluetooth function.

7

Product descriptions BPC-ToolDelivery Contents

2.3 Delivery Contents

PPiieecceess DDeessiiggnnaattiioonn1 BPC-Tool with connecting

cable for battery

1 Operating instructions

1 DVD

2.3.1 Checking Delivery Contents

Please check the delivery contents upon receiving your tool so that complaints regarding any potential damage can be made immediately.

Proceed as follows to check the delivery contents:1. Check the package delivered to ensure that it is not damaged.

Should you identify any damage to the package, then open the package in the presence of the delivery service and check the tool for hidden damage. Any transport damage to the package supplied and damage to the tool shall be registered in a damage report by the delivery service.

2. Open the package supplied and check for completeness based on the delivery slip.

3. Remove the BPC-Tool from the packaging.

CAUTION

Risk of short circuit due to loose parts in or on the BPC- Tool

Risk of destruction of the BPC-Tool and/or the vehicle electronics

Never put the BPC-Tool into operation if you suspect that there are loose parts in or on the BPC-Tool.

Please immediately contact the Hella Gutmann repair service or a Hella Gutmann trading partner.

8

BPC-Tool Product descriptionsTop

4. Check the BPC-Tool for mechanical damage and shake it lightly to ensure that there are no loose parts inside.

2.4 Top

DDeessiiggnnaattiioonn1 LC display

Liquid crystal display2 Function key 1

Here you can confirm a function.

If a function is available, the function type is shown at the bottom right of the display.

3 Arrow keys

Navigate with the cursor in menus or functions.4 Alphanumeric keypad

Here you can enter numerical values.

9

Product descriptions BPC-ToolConnectors

DDeessiiggnnaattiioonn5 On/off key

Here you can switch the BPC-Tool on and off.6 Function key 2

Here you can confirm a function.

If a function is available, the function type is shown at the bottom left of the display.

2.5 Connectors

DDeessiiggnnaattiioonn7 Infrared sensor

Here you can perform temperature measurements.8 ST3 connection

Here you can connect additional measuring instruments such as a current clamp.

9 Connecting cable for battery

2.6 Power supply

The BPC-Tool is preferably supplied with power via the connected battery. If there is no battery connected or if the battery does not provide sufficient voltage, six 1.5 V AA batteries are used as the voltage source.

10

BPC-Tool Product descriptionsPower supply

2.6.1 Replacing the Type AA Batteries

To replace type AA batteries:1. Switch off the BPC-Tool and remove all connecting cables.

2. Remove the screw from the battery compartment cover.

11

Product descriptions BPC-ToolPower supply

3. Remove the battery compartment cover with care.

4. Remove the batteries individually.

CAUTION

Pay attention to correct installation direction/polarity

5. Reassembly in reverse order

12

BPC-Tool Putting the BPC-Tool into operationSwitching on the BPC-Tool

3 Putting the BPC-Tool into operation3.1 Switching on the BPC-Tool

To switch on the BPC-Tool:

• Use to switch on the BPC-Tool.The BPC-Tool is switched on.

3.2 Switching off the BPC-Tool

To switch off the BPC-Tool:

• Use to switch off the BPC-Tool.The BPC-Tool is switched off.

13

Configuring the BPC-Tool BPC-ToolConfiguring the time zone

4 Configuring the BPC-Tool4.1 Configuring the time zone

To configure the time zone:1. Select Settings in the main menu and confirm with Select.2. Select >Time zone<.3. Use to select the desired time zone.

The selection is saved automatically.4. Return to the main menu with Back.

4.2 Setting the Time Format

Proceed as follows to set the time format:1. Select Settings in the main menu and confirm with Select.2. Select >Time format<.3. Use to select >24 hours< or >12 hours<.


4.3 Configuring summer time

To configure summer time:1. Select Settings in the main menu and confirm with Select.2. Select >Summer time<.3. Use to select >Activated< or >Deactivated<.


4.4 Setting the Date Format

Proceed as follows to set the date format:1. Select Settings in the main menu and confirm with Select.2. Select >Date format<.

14

BPC-Tool Configuring the BPC-ToolConfiguring the language

3. Use to select >DD-MM-YYYY< or >MM/DD/YYYY<.The selection is saved automatically.

4. Return to the main menu with Back.

4.5 Configuring the language

To configure the language:

1. Select Settings in the main menu and confirm with Select.2. Select >Language<.

3. Use to select the desired language.The selection is saved automatically.


4.6 Configuring the temperature units

To configure the temperature units:

1. Select Settings in the main menu and confirm with Select.2. Select >Temperature unit<.

3. Use to select >°C (degrees Celsius)< or >°F (degrees Fahrenheit)<.The selection is saved automatically.


4.7 Configuring the decimal separator

To configure the decimal separator:

1. Select Settings in the main menu and confirm with Select.2. Select >Decimal separator<.

3. Use to select >, (comma)< or >. (full stop)<.The selection is saved automatically.


15

Configuring the BPC-Tool BPC-ToolConfiguring the display contrast

4.8 Configuring the display contrast

To configure the display contrast:1. Select Settings in the main menu and confirm with Select.2. Select >Display contrast<.3. Use to select the desired contrast value.


4.9 Standby time

The period after which the BPC-Tool changes to standby mode is displayed here. The value is preset ex works and cannot be changed.

4.10 Configuring instructions

Here you can configure whether additional instructions should be displayed. We recommend that all instructions remain enabled.

To configure instructions:1. Select Settings in the main menu and confirm with Select.2. Select >Instructions<.3. Use to select >Activated< or >Deactivated<.


16

BPC-Tool ServiceCalling up product information

5 ServiceHere you can call up detailed information on the following functions:

• Product information

• Self-test

• Memory information

You can also perform a factory reset here.

5.1 Calling up product information

Among other things, this includes all information required for identification of the BPC-Tool.

Proceed as follows to call up product information:

1. In the main menu, select Service and confirm with Select.2. Select >Product information< and confirm with Select.

The information window appears. The information here includes the firmware version and the serial number.


5.2 Calling up self-test

Here you can see system parameters, including those of the internal memory, the internal batteries and Bluetooth.

Proceed as follows to call up the self-test:

1. In the main menu, select Service and confirm with Select.2. Select >Self-test< and confirm with Select.

Information including the following appears:

• Battery voltage

• State of charge

• Bluetooth status


17

Service BPC-ToolCalling up memory information

5.3 Calling up memory information

To call up memory information:1. In the main menu, select Service and confirm with Select.2. Select >Memory information< and confirm with Select.

Memory information appears.3. Return to the main menu with Back.

5.4 Performing a factory reset

Here you can reset the BPC-Tool to its factory settings. All data and files are reset to their state on delivery if you perform the factory reset.

Proceed as follows to perform a factory reset:1. In the main menu, select Service and confirm with Select.2. Select >Factory reset< and confirm with Select.3. Observe the confirmation prompt.4. Confirm the confirmation prompt with Yes.

The BPC-Tool is automatically reset to its state on delivery.5. Return to the main menu with Back.

18

BPC-Tool Working with the BPC-Tool via a diagnostic toolPreconditions for connecting the BPC-Tool

6 Working with the BPC-Tool via a diagnostic tool6.1 Preconditions for connecting the BPC-Tool

• Diagnostic tool supports use with BPC-Tool.

6.2 Connection to the diagnostic tool

Proceed as follows to connect the BPC-Tool to a diagnostic tool:1. Select Enable connection in the main menu and confirm with

Select.The Bluetooth symbol is displayed in the header.

2. Confirm the info window with Close.3. Configure the diagnostic tool for connection to the BPC-Tool according

to the user manual.The BPC-Tool can now be used via the diagnostic tool.

For a description of how to use the BPC-Tool with a diagnostic tool, see the documentation of the respective diagnostic tool.

19

Working with the BPC-Tool BPC-ToolSymbols

7 Working with the BPC-Tool7.1 Symbols

SSyymmbbooll MMeeaanniinnggBattery test

Here you can perform a battery test for vehicles without a start/stop function.Start/stop test

Here you can perform a battery test for vehicles with a start/stop function.System test

Here you can perform a system test for vehicles with or without a start/stop function.Enable connection

Here you can enable the Bluetooth connection.Reports

Here you can view a report on the last battery test or system test, among other things.Service

Here you can call up detailed information on the BPC- Tool, for example:

• Serial number• Bluetooth status• Battery test resultSettings

Here you can configure the BPC-Tool.

7.2 Connecting the BPC-Tool to the battery

7.2.1 Preconditions for battery test

Ensure the following in order to perform a battery test:

20

BPC-Tool Working with the BPC-ToolConnecting the BPC-Tool to the battery

• Parking brake pulled

• Park position also engaged in automatic vehicles.

• Protect vehicle against rolling away.

• Battery in perfect state of maintenance.

7.2.2 Connecting the terminal clamps

CAUTION

Overvoltage

Fire hazard/risk of destruction of the BPC-Tool and its surroundings

Comply with the maximum permitted voltage load of the BPC-Tool:

• Direct voltage: 35 V

NOTE

When the battery has been removed from the vehicle, ensure the following:

• Always use lifting gear or a strap to lift the battery.

To connect terminal clamps to the battery:1. Connect the red terminal clamp to the positive terminal (+).

2. Connect the black terminal clamp to the negative terminal (–).If the terminal clamps have been connected to the battery incorrectly, the following text is displayed: Incorrect polarity of terminal clamps, connect red to positive terminal (+) and black to negative terminal (-).

3. If the terminal clamps have been connected incorrectly, repeat steps 1 + 2.If it is not possible to perform a battery test, the following texts are displayed: Bad terminal clamp connection or cable problem. Check terminal clampsor Unstable battery detected. Check terminal clamp connection.

4. If battery testing is not possible, remove the terminal clamps, clean the pins and reconnect the terminal clamps.

21

Working with the BPC-Tool BPC-ToolPerforming a battery test

7.3 Performing a battery test

NOTE

The BPC-Tool can display additional instruction texts on request. To view additional instruction texts run through steps 1–4 as described underConfiguring instructions (Page 16).

Proceed as follows to perform the battery test:

1. In the main menu, select Battery test and confirm with Select.

2. Select the battery position and confirm with Next.

3. Select the battery type and confirm with Next.

4. Select additional subitems if required.

5. Select the battery standard and confirm with Next.

6. Enter the cold cranking amps and confirm with Next.

7. Select additional subitems if required.

8. Direct the front of the BPC-Tool at the battery.

9. Confirm the temperature display with Next.The message Perform battery test for discharged battery? appears if the battery is flat.

Compared to the simple battery test, the battery test for discharged batteries performs additional tests so that the battery can be quickly and reliably evaluated despite low voltage.

10. If necessary, perform the battery test for discharged batteries with Yes.Alternatively, you can choose not to perform a battery test for discharged batteries by selecting No. In this case, a simple battery test is performed.

22

BPC-Tool Working with the BPC-ToolPerforming a start/stop test

11. Follow the on-screen instructions.Battery test is performed. The battery test result appears.

If the battery test was successful, the following appears:

• Good - recharge.Allow the battery to charge and put back into operation.

• Battery OK.Put battery back into operation.

• Cell defective, replace battery.Replace battery and test it again, if necessary.

• Replace the battery.Replace battery and test it again, if necessary.

This message may also be displayed if the terminal contact with the battery is insufficient, for example. In this case, disconnect the battery and test it again by selecting >Outside the vehicle<.

12. Return to the main menu with Next.

7.4 Performing a start/stop test

NOTE


Proceed as follows to perform the start/stop test:

1. In the main menu, select Start/stop test and confirm with Select.

2. Run through steps 2–10 as described in the section headed Performing a battery test (Page 22).

23

Working with the BPC-Tool BPC-ToolPerforming a system test

3. Follow the on-screen instructions.The start/stop test is performed. The result of the start/stop test is displayed.

If the start/stop test was successful, the following appears:

• Charge and test again.Allow the battery to charge completely and test it again.



• Cell defective, replace battery.Replace battery and test it again, if necessary.

• Replace the battery.Replace battery and test it again, if necessary.

This message may also be displayed if the terminal contact with the battery is insufficient, for example. In this case, disconnect the battery and test it again by selecting >Outside the vehicle<.

4. Return to the main menu with Next.

7.5 Performing a system test

If the BPC-Tool is connected to a Hella Gutmann diagnostic tool, software version 47 or higher must be installed on the diagnostic tool in order to perform the system test.

The following tests are performed consecutively by the BPC-Tool during the system test:

• Battery test

• Starter test

• Alternator test

• Resistor test

24

BPC-Tool Working with the BPC-ToolPerforming a system test

NOTE

A blue current clamp (CP 700) is required for a complete system test. Without a current clamp, the current intensity is not measured during the starter and alternator tests. The resistor test is not applicable at all.

NOTE


Proceed as follows to perform the system test:1. Insert the electrical connector of the current clamp into the ST3

connection of the BPC-Tool with the arrow pointing down.

2. In the main menu, select System test and confirm with Select.3. Select the vehicle type and confirm with Next.4. Run through steps 3–10 as described in the section headed

Performing a battery test (Page 22).5. Follow the on-screen instructions.

The system test is carried out. The battery test result appears.

If the battery test was successful, the following appears:

• Charge and test again.Allow the battery to charge completely and test it again.



• Cell defective, replace battery.Replace battery and test it again, if necessary.This message may also be displayed if the terminal contact with the battery is insufficient, for example. In this case, disconnect the battery and test it again by selecting >Outside the vehicle<.

6. Continue the system test with the starter test with Next.

25

Working with the BPC-Tool BPC-ToolReports

7. Follow the on-screen instructions and confirm with Next.The starter test results appear.

8. Continue the system test with the resistor test with Next.9. Follow the on-screen instructions and confirm with Next.

The resistor test result appears.10. Continue the system test with Next.

A summary of the system test appears.11. Return to the main menu with End.

7.6 Reports

The following reports can be displayed here:

• Result of the last battery test• Statistics of all battery tests

7.6.1 Calling up the battery test result

Proceed as follows to call up the last battery test result:1. In the main menu, select Reports and confirm with Select.2. Select >Battery test result< and confirm with Select.

The last battery test result is displayed.3. Return to the main menu with Back.

7.6.2 Calling up the battery test statistics

To call up the battery test statistics:1. In the main menu, select Reports and confirm with Select.2. Select >Batt.test statistics< and confirm with Select.

The battery test statistics are displayed.3. Return to the main menu with Back.

7.6.3 Calling up the system test result

To call up the last system test result:

26

BPC-Tool Working with the BPC-ToolReports

1. In the main menu, select Reports and confirm with Select.2. Select >System test result< and confirm with Select.

The last system test result is displayed.3. Return to the main menu with Back.

7.6.4 Calling up the system test statistics

To call up the system test statistics:1. In the main menu, select Reports and confirm with Select.2. Select >Syst.test statistics< and confirm with Select.

The system statistics appear.3. Return to the main menu with Back.

7.6.5 Deleting statistics

To delete test statistics:1. In the main menu, select Reports and confirm with Select.2. Select >Batt.test statistics< or >Syst.test statistics< and confirm

with Select.3. Use Delete to delete the test statistics.4. Observe the confirmation prompt.5. Confirm the confirmation prompt with Yes.

The test statistics are deleted.6. Return to the main menu with Back.

27

BPC client App BPC-ToolInstallation

8 BPC client AppThe BPC client App makes it possible to use the BPC-Tool as a stand- alone tool. The BPC client App provides the following functions:

• Assigning the BPC-Tool• Updating the BPC-Tool• Printing the battery test result• Printing the system test result

8.1 Installation

8.1.1 System requirements

• At least 128 MB free internal memory (RAM)• At least 75 MB free hard disc space• At least 1 free USB port at the PC• Windows administrator rights (for installation)

8.1.2 Supported operating systems

• Microsoft Windows Vista or higher• Microsoft Windows 7 or higher• Microsoft Internet Explorer 8 or higher

8.1.3 Installing the BPC client App

An installation wizard guides you through the necessary steps.

Proceed as follows to install the BPC client App:1. Switch on the PC.2. Bring up the Hella Gutmann homepage.3. Select BPC-Tool under Tools.4. Select the >BPC client App< tab.

The HGS Update Service window is displayed.5. Select the >Software< tab.

28

BPC-Tool BPC client AppInstallation

6. Install the BPC client App using .The BPC client App Setup window is displayed.

7. Click >Next<.The general terms and conditions appear.

8. Read the general terms and conditions and confirm them at the end of the text.

9. Click >Next<.A drop-down list appears.

A target directory for the BPC client App files is suggested. If you wish to have another target directory then use the >Select...< function to select a suitable directory. At the end of installation, the files will be copied into the selected target directory.

10. Click >Next<.

11. Click >Install<.If the programme Microsoft Visual C++ is not installed on the PC, the GTCs for Microsoft Visual C++ are displayed.

12. Read and confirm the Microsoft Visual C++ GTCs if necessary.

13. Click >Install<.The Microsoft Visual C++ installation is started.

14. Wait until the installation is finished.

15. Click >Close<.The Microsoft Visual C++ installation is finished.

The BPC client App installation is started.

16. If necessary, confirm the Windows safety precautions for installation.

17. Wait until the installation is finished.

18. Click >Finish<.Files are copied to the selected target directory.

This concludes the installation of the BPC client App.

29

BPC client App BPC-ToolPutting the BPC client App into operation

8.2 Putting the BPC client App into operation

8.2.1 Connecting to the PC

NOTE

The BPC client App must always be connected via Bluetooth to the PC on which the BPC client App is being used and to the BPC-Tool.

The BPC client App contains software components. Certain functions of the BPC client App therefore require a connection to Bluetooth.

8.2.2 Executing the BPC client App

NOTE

When starting the app for the first time, the BPC client App must be coupled via Bluetooth. This required the BPC client App to be connected to the Bluetooth adapter.

Proceed as follows to execute the BPC client App:1. Activate the Bluetooth function of the PC or insert the Bluetooth

adapter into the USB port of the PC.

2. Go to Start > All Programmes > Hella Gutmann Solutions and selectBPC client App.

The BPC client App is started.

File Settings Help

8.2.3 Closing the BPC client App

Proceed as follows to close the BPC client App:

• Close the BPC client App under File > Close.

30

BPC-Tool BPC client AppConfiguring the BPC client App

8.3 Configuring the BPC client App

8.3.1 Configuring the language

Here you can set the language version if the software is multilingual. After having set the language, the BPC client App is displayed in this language.

To configure the language:1. Select Language under > Settings.

The selection of languages depends on the specific software.2. Select the required language.The selection is saved automatically.

8.3.2 Entering the workshop data

Proceed as follows to enter company or workshop data:1. Select Workshop data under > Settings.2. Enter the company name under Company.3. Repeat step 2 to make more entries.4. Confirm your entry with >OK<.Inputs are saved automatically.

8.3.3 Printing with a standard PC printer

Here you can set the default printer for printing with the PC.

If there is no additional printer connected to the tool, it is possible to print with the printer of a PC system. This requires a connection between the tool and the PC. The connection to the PC can be established via the USB port, Ethernet, Bluetooth, WLAN or UMTS.

NOTE

If the default printer is not selected, you are prompted to select a printer when a print job is submitted.

To print to the default printer:

• Activate Use default printer under > Settings.A blue check mark is set in front of >Use default printer<.

31

BPC client App BPC-ToolWorking with the BPC client App

Now you can start printing via the PC.

8.4 Working with the BPC client App

8.4.1 Searching for the BPC-Tool

To search for BPC-Tool:1. Activate the Bluetooth function of the PC or insert the Bluetooth

adapter into the USB port of the PC.2. Switch on the BPC-Tool und connect it to the Bluetooth adapter.3. Select Search for BPC-Tool under > Settings.

The connection to the BPC-Tool is established.

The connection to the BPC-Tool via the tool is established correctly if the text BPC-Tool found and saved is displayed.

4. Confirm the info window with >OK<.The selection is saved automatically.

In the bottom toolbar, the selected serial number of the BPC-Tool is displayed, such as BPC-Tool: BPC_0814200xxx — 00:06:66:xx: xx:Ax

8.4.2 Starting a BPC Tool update

NOTICE

Insufficient voltage supply

System data loss

Do not switch off the tool and the BPC-Tool during the update and do not disconnect them from the voltage supply.

Ensure sufficient voltage supply.

Proceed as follows to start the BPC Tool update:1. Connect the BPC-Tool to the battery.2. Select Update BPC-Tool under > Settings.

If the most recent version is installed on the BPC-Tool, the following text is displayed: Software already up to date.

32

BPC-Tool BPC client AppWorking with the BPC client App

The BPC Tool update starts.

The tool searches for a new update that is then downloaded and installed.

8.4.3 Printing the battery test result

Proceed as follows to print battery test result:1. Print the battery test result using .

The Enter additional data window is displayed.

Customer DataName:Street/no.:Postal code/city:

Vehicle dataVehicle:Engine code:Model year:Kilometrage:VIN:Inspector:

Customer data can be entered here.

NOTE

If customer data is entered, it is not saved. Following a BPC client App restart, any customer data that may have been entered previously is deleted.

2. Enter the customer data if necessary.3. Confirm entries using >OK<.

NOTE

If the default printer has not been activated in the settings, you are prompted to select a printer when a print job is submitted.

4. Select and confirm the desired printer if necessary.

33


The progress bar is displayed.

The battery test result is printed.

34


Workshop dataDate

Customer DataVehicle data

Battery diagnosticsTest parameters Determined valuesBattery position : xxx Voltage [V] : xxx

Temperature measurement

: xxx Cold cranking amps [A]

: xxx

Battery type : xxx Temperature [°C] : xxx

Battery standard : xxx

Cold cranking amps [A]

: xxx

Battery testBattery OK. Recharge the battery.

Battery state of charge (xx)

75 %Battery state of health (xx)

8.4.4 Printing the system test result

Proceed as follows to print system test result:

35


1. Print the system test result using .The Enter additional data window is displayed.

Customer DataName:Street/no.:Postal code/city:

Vehicle dataVehicle:Engine code:Model year:Kilometrage:VIN:Inspector:

Customer data can be entered here.

NOTE

The customer data is not saved. Following a BPC client App restart, any customer data entered previously is no longer available.

2. Enter the customer data if necessary.3. Confirm entries using >OK<.

NOTE

If the default printer has not been activated in the settings, you are prompted to select a printer when a print job is submitted.

4. Select and confirm the desired printer if necessary.The progress bar is displayed.

The system test result is printed.

36


Workshop dataDate

Customer DataVehicle data

Battery diagnosticsTest parameters Determined valuesBattery position : xxx Voltage [V] : xxx

Temperature measurement

: xxx Cold cranking amps [A]

: xxx

Battery type : xxx Temperature [°C] : xxx

Battery standard : xxx

Cold cranking amps [A]

: xxx

Battery testBattery OK. Recharge the battery.

Battery state of charge (xx)

75 %Battery state of health (xx)

37


Starter testVoltage [V] : xxx

Current [A] : xxx

Time [s] : xxx

Resistor [mOhm] : xxx

Battery starting voltage OK

Alternator testPower consumer switched off.

Power consumer switched on.

Voltage [V] : xxx Voltage [V] : xxxCurrent [A] : xxx Current [A] : xxx

Charging voltage OK

Power consumer switched off.

Power consumer switched on.

Resistor testNo-load current [A] -1.30

The waiting time until all installed ECUs are in energy saving mode varies depending on manufacturer and model.

38

BPC-Tool General informationProblem solutions

9 General information9.1 Problem solutions

The following list will help you to solve minor problems yourself. Select the relevant problem description and check and perform the steps listed under Solution in sequence as necessary until the problem is solved.

Problematic case SolutionBPC-Tool does not boot. • Press the on/off button.

• Check the connection of the connecting cable to the BPC- Tool and the battery.

• Charge the battery.• Replace the type AA batteries in

the BPC-Tool.

9.2 Care and maintenance

• Like every tool, the BPC-Tool must be handled with care.• Regularly clean the BPC-Tool with non-aggressive cleaning agents.• Use commercial household cleaning detergents and a moistened, soft

cleaning cloth.• Replace damaged cables/accessories immediately.• Always use original spare parts.

9.3 Disposal

NOTE

The guidelines listed here are exclusively valid within the European Union.

In compliance with Directive 2012/19/EU of the European Parliament and Council of 4 July 2012 relating to Waste Electrical and Electronic Equipment (WEEE), and the German national statute governing the distribution, return and environmental disposal of electrical and electronic

39

General information BPC-ToolBPC-Tool technical data

equipment (Electrical and Electronic Equipment Act – ElektroG) of 16 March 2005, we are obliged to take back this tool, distributed by us after 13.08.2005, at the end of its service life free of charge and to dispose of it in accordance with the above-mentioned directives.

Since, in the case of the present device, this relates to exclusively commercially used equipment (B2B), it must not be handed over to a public disposal facility.

The tool can be disposed of at the following address (specifying the date of purchase and the device numbers):

Hella Gutmann Solutions GmbH Am Krebsbach 2 79241 Ihringen GERMANY WEEE reg. no.: DE25419042 Phone: +49 7668 9900-0 Fax: +49 7668 9900-3999 E-mail: [email protected]

NOTE

Batteries contain toxic substances. Therefore, do not throw used batteries into household waste but dispose of them properly.

The batteries can also be sent to Hella Gutmann for disposal free of charge.

9.4 BPC-Tool technical data

General data

Supply voltage 10–15 VBattery measuring range

1.5–16 V

Batteries 6x 1.5 V AAAmbient temperature Working range: 0 - 50°CDimensions 60 x 110 x 231 mm (H x W x D)

40

BPC-Tool General informationBPC-Tool technical data

Interfaces 1x ST3

Bluetooth class 1 (max. 3 Mbit/s)Operating range Inside: max. 10 m

Outside: max. 20 m

41

Notes BPC-Tool

Notes

42

BPC-Tool Notes

Notes

43

HELLA GUTMANN SOLUTIONS GMBHAm Krebsbach 2 79241 Ihringen GERMANY Phone: +49 7668 9900–0 Fax: +49 7668 9900–3999 [email protected] www.hella-gutmann.com

© 2016 HELLA GUTMANN SOLUTIONS GMBH

1 STUECK/PIECE(S)

�� 9XQ 460 988-171

Made in Germany

operating instructions bpc-tool englisch · bpc-toolis connected directly to the battery by the...

Documents