one-piece toilet installation instructions swiss …

6
www.swissmadison.com | 1-434-623-4766 | [email protected] Swiss Madison ® INSTALLATION INSTRUCTIONS One-Piece Toilet @SwissMadison #WellMadeForever

Upload: others

Post on 22-Oct-2021

8 views

Category:

Documents


0 download

TRANSCRIPT


www.swissmadison.com | 1-434-623-4766 | [email protected]

Swiss Madison®

INSTALLATION INSTRUCTIONSOne-Piece Toilet

@SwissMadison#WellMadeForever


— 1 —

If you have any questions or concerns please contact us:1-434-623-4766

[email protected]

PRIOR TO INSTALLATION:· Inspect toilet to ensure no damages have occurred while in shipping. · Observe all plumbing and building codes in accordance with your state and local requirements. · All dimensions are nominal! Be sure to measure your toilet prior to installation. · The step-by-step guidelines in the installation instructions are a general reference. Should there be

any discrepancies, Swiss Madison cannot be held liable. It is recommended to install all Swiss Madison products by hiring a licensed professional.

· Read installation and maintenance instructions thoroughly before installing. Be sure to use proper tools and always wear proper personal safety accessories for your protection.

· Two people are recommended to handle and install this product as it is fragile.

INCLUDED PARTS:SUGGESTED TOOLS & MATERIALS:

Safety Glasses

Wrench

Level Screwdriver

Putty Knife Tape Measure

HacksawFlexible Supply Tube

ONE-PIECE TOILET INSTALLATION INSTRUCTIONS

Bolts

Cover Caps

Wax Ring/ Gasket

One-PieceToilet


— 2 —

ONE-PIECE TOILET INSTALLATION INSTRUCTIONS

3. Install Closet Bolts · Install closet bolts to flange channel, turn 90° and

slide into place 6” (152mm) apart and parallel to wall.

2. Rough-In the Toilet · Measure the wall from behind the toilet to the middle of the closet bolt. Your rough-in measurement should be around 10”.

4. Install Wax Seal · Invert toilet on floor (use cushion to prevent

damage), and install wax ring evenly around waste flange with tapered end of ring facing toilet. Apply a thin bead of sealant around toilet base.

1. Turn Off Water Supply· Close toilet supply valve and flush tank completely, use towel to remove excess water.

· Disconnect and remove supply line, if you are replacing the valve shut main water supply first.

· Remove closet bolts from flange and clean wax and putty from base area.

5. Position Toilet on Flange · Hand-tighten water supply hose to the fill valve in the back of the toilet. Do not connect to water supply yet.

· Unplug floor waste opening and install toilet on closet flange so bolts project through the mounting holes.

· Loosely install retainer washers and nuts.

6. Install Toilet · Position toilet square to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly sealed to floor. Do not over-tighten nuts, it might crack ceramic.

· Smooth off the bead of sealant around the base. Remove excess sealant.

· Place cover caps to hide installation holes on toilet.· Connect water supply to shut off valve, and check for leaks. Tighten if necessary.

Closet Flange

Closet Bolts

Rough-in

Nut

Washer

Bolt

Wax Ring

Sealant


ONE-PIECE TOILET INSTALLATION INSTRUCTIONS

TOILET SEAT INSTALLATION

— 3 —

1. Disassemble· Disassemble the cover cap and the hinge.

2. Construct Hinges· Insert screw and nut into the hole on the hinge. · Attach blind hole screw fixing to the bottom of screw.

3. Attach Hinges· Insert hinges with blind hole screw fixings attached

into holes on toilet bowl.· Lightly tighten hinges with a screwdriver too allow for later adjustment.

Pull

4. Adjust and Cover Hinges· Be sure the hinge is all the way forward for proper seat fitting.

· Place the covers onto the hinges.

or

Incorrect: Correct:


ONE-PIECE TOILET INSTALLATION INSTRUCTIONS

— 4 —

5. Adjust and Attach Seat· Align seat to the hinges then firmly tighten the hinges. · Attach seat to the secure hinges.· Adjust seat to align to the bowl.

TOILET SEAT USAGE· To remove, push middle button until you hear a “click”, then pull straight up.· To re-install, align hinge posts with reference marks on seat, then push down until your hear a “click”.

*Click* *Click*

One Button:

Two Button:

*Click* *Click*


1-434-MADISON(623-4766)

19 Stults RoadDayton, NJ 08810

www.swissmadison.comONE YEAR LIMITED WARRANTY

Swiss Madison® products are made with quality materials and excellent craftsmanship to provide our customers with beautiful, durable, long-lasting products. Should there be any defects in materials or craftsmanship under regular use that are discovered within the first year of installation, Swiss Madison® will provide replacement parts at no charge, or at its discretion, replace any product or part of the product that is deemed defective, under normal installation, use, service or maintenance. This warranty applies only to the original purchaser. Proof of purchase will be required in the instance of a claim.

Swiss Madison® recommends all installations of Swiss Madison® products to be conducted by a licensed, professional plumber or contractor. Swiss Madison® will not be held responsible for any damage or product failure due to improper installation, misuse, or failure to utilize a licensed professional for installation. Swiss Madison® is not responsible for any installation or removal costs. This One Year Limited Warranty Will Be Voided If: • The installation recommendations were not followed by the installer • The product has been moved from its initial place of installation • The product has in any way been modified from its packaged state • The product has been subjected to improper maintenance, abuse, misuse, excessive use of chemicals, accidents, or other damages, etc.

Swiss Madison® makes no implication that its products comply with any local building or plumbing codes. It is the consumer’s responsibility and obligation to determine local code compliance prior to and during installation. This warranty extends only to the original purchaser and first consumer.

Swiss Madison® is not responsible for any special, incidental or consequential damages associated with the installation, replacement, return or use of the original purchaser’s product. This includes, but is not limited to: freight costs, labor, travel time, lost profit, home damages and other contingent liabilities and costs (including, without limitation, costs associated with ‘professionals’ or ‘experts’, investigations, audits, analyses, attorneys and any other professional/hired services).

The Swiss Madison® warranty is a comprehensive and explicit limit of liability. All items not disclosed within the warranty are not addressable within the responsibility of Swiss Madison®. Certain states have variances regarding implied warranties; in those situations, we remain fully compliant.

If you have any questions or concerns, please contact us directly at

1-434-MADISON (623-4766)

WARNING: Contents of your order may contain sharp and possibly other harmful pieces and may cause hazard to children and adults. Swiss Madison® is not responsible in any way for personal damages.

Swiss Madison®