Active DirectOn LineInstructions for use

取扱説明書使用說明

2

Index

I. Congratulations Page 3

II. Ensuring you get the best from your system Page 4 – 13

III. Important notes Page 14

IV. BRITA, quality and satisfaction guaranteed Page 15

I. 新しい＜ブリタ＞浄水器をお買い上げのお客様へ Page 16II. 正しくお使いいただくために Page 17 – 24III. 重要事項 Page 25IV. BRITA, quality and satisfaction guaranteed Page 26

V. ブリタクラブ Page 27VI. BRITA製品保証について Page 28 – 29

I. 恭喜您 頁碼 30II. 確保獲得本系統最大效益 頁碼 31 – 40III. 重要須知 頁碼 41IV. BRITA 品質與滿意保證 頁碼 42

ENGLISH

日本語

繁體中文

ENGLISH 3

Your BRITA system, with its dedicated BRITA water dispenser, is the key to cleaner, clearer great tasting fi ltered water

The BRITA fi lter

• improves taste• is economical and convenient

The On Line Active A 1000 fi lter 0.5 micron carbon block fi lter cartridge signifi cantly reduces:

• Chlorine, unpleasant tastes and odors• Small particles (such as rust, dust and sand)• Organic impurities

Lifetime of the On Line A 1000 fi lter cartridge

On Line A 1000 fi lter cartridge life depends on local water quality. For optimum performance and hygiene, it is recommended that the fi lter cartridge be replaced at least six-monthly.Your digital BRITA cartridge exchange indicator displays the remaining number of days until the fi lter cartridge is to be replaced and alerts you with an audible alarm after 180 days to change the cartridge. You should check the digital display periodically. For more information, see chapter 3.2.

I. Congratulations on your new BRITA® On Line Active Direct Filter System

You are assured of BRITA quality and our commitment to customer service and support.

BRITAwater dispenser

On Line A 1000fi lter cartridge

BRITA cartridge exchange indicator

4 ENGLISH

II. Ensuring you get the best from your system

1 Terms of warranty

The On Line Active Direct fi lter system is designed to operate at a maxi-mum pressure not exceeding 8.6 Bar (860 kPa or 124 psi) and an intake temperature of 30 °C and an ambient temperature of 40°C. The On Line Active Direct fi lter system is warranted to be free from defects in mate-rial and workmanship for a period of two years from date of purchase (the warranty period does not apply to the fi lter cartridge which is a con-sumable). The warranty is expressly limited to the replacement of any part or parts proving defective providing the installation has been fully in accordance with these instructions and all relevant plumbing codes and standards, and provided that the pressure and temperature at which the fi lter is operated at all times do not exceed the limits stated herein. The warranty shall be voided by mechanical damage caused during installation. Save insofar as they may be excluded by law, this warranty is given in lieu of all other expressed or implied warranties or conditions and there shall be no liability for damages, consequential or otherwise.

2 Contents of the On Line Active Direct Kit

To ensure you get the best result from your BRITA On Line Active Direct Water Filter System, please follow these instructions carefully.

Your On Line Active Direct Water Filter Kit includes the following (see fi g. 1):1. On Line fi lter head with three settings (“C”, “+”, and ”++”)

including a convenient locking handle2. Flexible wall mount bracket for fi lter head3. On Line A 1000 water fi lter cartridge4. BRITA water dispenser5. Electronic BRITA cartridge exchange indicator with digital

display and audible alarm6. Hose (1), length = 800 mm, 1/2" female nut at one end and

3/8" female nut at other end – for connection between the cold water connection point and the inlet side of the fi lter head,(1/2" and 3/8" washers included in washer pack)

7. Hose (2), length = 800 mm, 3/8" female nut at one end and 7/16" female nut at other end – for connection from the outlet side of the fi lter head to the BRITA water dispenser. (3/8" washer included in washer pack; 7/16" washer in place in hose.)

8. Usage instructions9. Isolating (shut-off) valve and Pressure Limiting Valve with

back-fl ow prevention and adapterBefore installation, please ensure you have a free 1/2" cold water supply connection point to which you can connect the On Line Active Direct Water Filter system (in addition to your existing kitchen tap and any other installed appliance/s). If you do not have a free 1/2" cold water connection, please contact a licensed specialist.

1. 2.

3. 4.

5. 6.

7. 8.

9.

(fi g. 1)

ENGLISH 5

Recommended tools for installation: one Allen hexagonal key (5 mm), one 12 mm drill (suitable for surface where BRITA dispenser is to be mounted), adjustable spanner for different sizes.Recommended for installation of the wall mount bracket: two screws (e.g. 5 mm in size) and two wall plugs (if necessary). Please use appropriate screws and wall plugs for the type of wall in the under-sink compartment.

3 Installation of the On Line Active Direct Kit

!

Installation of the fi lter system must comply with the relevant state or local plumbing regulations and standards (AS/NZS 3500). Depending on the necessary method of connection to the cold water supply, additional valves/adaptors/components may be required, and the services of a licensed plumber may be necessary. If you do not have an available connection to the cold water supply and it is necessary to cut into the cold water supply line, a licensed plumber is required.

Before starting, please check that you have all the components as listed above (see fi g. 1) as well as the recommended tools.There are 7 steps to the installation.

!Prior to installation, read the Technical Data (chapter 8) and the Important Information (chapter 9). (After storage and transport below 0°C, the product must be stored in the open original packaging for at least 24 hours at the stated ambient temperatures (chapter 8) for operation.)

3.1 Step 1: Selecting appropriate setting on the fi lter head

The fi lter head is set to the “++” setting by default. For use with the supplied A 1000 fi lter cartridge you need to change the setting in the window to “C”. Use an Allen key (hexagonal socket wrench) and turn the hexagonal nut in the direction of the arrow in the window until the “C” appears. Refer fi g. 2)(If the optional alternative fi lter cartridge, model Active Plus P 1000 (for hard water situations) is to be installed, the setting required is “+” or “++” depending on the determined water hardness.)

(fi g. 2)

3.2 Step 2: Programming the electronic BRITA cartridge exchange indicator

A Commissioning:

Please insert the enclosed batteries (2 x AA) into the appropriate compartment of the electronic BRITA cartridge exchange indicator. A long beep will sound after insertion of the batteries.

B Initial Programming:

Important: Please program the timer for 180 days.Note: Please ensure that you activate the electronic BRITA car-tridge exchange indicator with display during the day-time so that when the alert is sounded to change the fi lter, it will start beeping at the exact time of day you originally set the indicator.Programming:

a Press the DISPLAY button briefl y to activate the display. Initially, the default setting of 90 days fl ashes.

b Press and hold the DISPLAY button and then press the START/RESET button briefl y. This activates the setting mode.

c Switch the display from 90 days to 180 days press the DISPLAY button briefl y.

d Wait until the time value stops fl ashing or the DISPLAY switches off.

e Now activate the 180-day timer by briefl y pressing DISPLAY and then press the START/RESET button.

6 ENGLISH

f A fl ashing spot in the bottom left of the display indicates that the timer is active.

C Reading the timer status

The display is activated by pressing the DISPLAY button briefl y during operation. The remaining time until the exchange of the cartridge is due is shown in days. If the time is exceeded, the time is displayed with a minus sign.

D Audible signals

a Signal to replace the cartridge: A long signal sounds on the hour every hour when there are less than 10 days before the end of the programmed 180 day setting (15 double beeps). A shorter reminder (5 double beeps) then sounds every 15 minutes until the next signal.

b Reminder function: Press any button to deactivate the signal for 72 hours if you prefer to be reminded to replace the cartridge at a later date.

c Battery change signal: When the batteries are depleted, a long signal sounds (15 single beeps) followed by a short reminder signal (5 single beeps) every 15 minutes until the next signal on the hour.

d Switching the device off: This is only possible by removing the batteries from the battery compartment.

E Activating the reset function when replacing the cartridge

a Press the DISPLAY button briefl y to activate the display.b Press and hold the START/RESET button for 5 seconds until a

long beep sounds.c The last 180 days programmed appear in the display.d The timer starts automatically.

F Changing the batteries

a After changing the batteries, a long beep sounds.b After the beep, briefl y press the DISPLAY button to activate the

display.c The remaining days since the last reset are now displayed.

(Caution: Only possible up to 16 hours after the batteries are fully depleted. After this time, the device reverts back to the factory setting and must be reprogrammed – see Point B).

G Installation

You can fi x the electronic BRITA cartridge exchange indicator to an appropriate and dry place by using the supplied Velcro hook and loop fastener. We recommend installing it under the sink in a posi-tion of easy visibility. Avoid contact with water/splashes!

Technical data:

• Batteries: 2 AA (removable)• Acoustic alarm: when batteries are low, or after 3 or 6 months• To avoid loss of data, change the battery within 12 hours.• After 16 hours without power, the appliance switches back to its

factory settings.• The display automatically switches to stand-by mode after

10 seconds.

(fi g. 3)

ENGLISH 7

3.3 Step 3: Installing the BRITA water dispenser

To install the BRITA water dispenser, fi rst make sure all the tools you need are in front of you.Required tools: Electric drill with 12-mm bit suitable for surface to be drilled); spanner for 7/16" nut.

1.

2.

3.

4.

5.

6.

(fi g. 4)

12 mm Drill

1. BRITA water dispenser2. Base (Work surface)3. Washer4. Counter plate5. Locking ring6. Hexagon nut (7/16")To start, fi nd a suitable place to install your BRITA water dispenser. We recommend installing it on a level section on the rear perimeter of your sink, space permitting; alternatively on the work surface adjoining the sink. It is important to ensure that there is clearance under the area where you will need to drill.Please, make sure that there is enough room and access under the sink to allow for the installation of the fi lter head and cartridge, and to connect the two supplied hoses. Determine the position for the convenient placement of the exchange indicator.

!

Please note that you will need the right drilling equipment for your particular work surface or base. Make sure the area under the dispenser is stable, especially if your work surface is not made from wood. Please check the drilling requirements for the material, use the appropriate drill and/or consult a specialist.

Drill a hole (with a 12-mm bit) into the surface where you wish to set up the BRITA water dispenser.Next, install the BRITA water dispenser (see fi g. 4).Then place the base (2) over the hole and fi x the BRITA water dispenser (1) in position using the supplied counter plate (4), the washer (3), the locking ring (5) and the hexagon nut (6).

3.4 Step 4: Attaching the hoses

!

The supplied hose for connection to the cold water supply requires the availability of an already installed 1/2" BSP male connection point (typically integrated with a mini-stop tap). Before installation, please ensure you have such a free 1/2" cold water connection point. If not, please contact a licensed plumber.In accordance with regulations, the shut-off valve (also called isolating valve) and the non-return valve (with back-fl ow prevention) which are included in your kit must be installed at the point of connection to the water supply before the fi lter system intake hose. Plumbing tape should be used on all threads in this sub-assembly and tested to ensure there are no leaks.

We recommend that you fi rst arrange all parts you need in front of you.Recommended tools for installation: one Allen key and an adjustable spanner.Recommended for installation of the wall mount bracket: two screws (e.g. 5 mm in size suited to the mounting surface) and two wall plugs (if necessary).

8 ENGLISH

Please follow the diagram below (see fi g. 5) and perform the steps in the right order.A a) Turn off the cold water supply b) Attach the supplied shut-off and pressure limiting valve set to

the free 1/2” male connection point to the cold water supply c) Insert the appropriate washers in the respective internal

threads at each end of inlet hose [1] (3/8" and 1/2"). d) Connect inlet hose [1] to the cold water supply (and ensure

that the washer is correctly positioned).B Now connect the end hose [1] to the fi lter head inlet (3/8"). This

is labelled “IN” (inlet) and marked with an arrow. Make sure the washer is seated correctly! Connect outlet hose [2]:

C The small washer (7/16") is already inserted in the end of the hose (2) – attach to the installed BRITA water dispenser (see Step 3.3).

D After the 7/16" end has been attached to the fi lter tap, insert theappropriate washer (3/8") in the end of the hose [2] and connect the 3/8" end of the hose [2] to the outlet on the fi lter head, labelled with the “OUT” arrow.

!The maximum tightening torque for all connections may not exceed 14 Nm! Only hoses with the connections and the supplied washers may be used. Use of hoses with conical screw connections will damage the connections of the fi lter head and invalidate any warranty claims.

Hose 2: 800 mm

C

3/8" 7/16"

B

3/8"Hose 1: 800 mm

A

1/2"

D

(fi g. 5)

Before installation, please check you have an additional 3/8" or 1/2" cold water supply.Consult a specialist dealer if necessary.

Cold water supply

WasherWashers

Filter exchange indicator

Shut-off and pressure limiting valve

BRITA water dispenser

Filter head

ENGLISH 9

3.5 Step 5: Inserting the fi lter cartridge (see fi g. 6)

A Remove the protective cap (1).B Insert the fi lter cartridge (5) vertically into the fi lter head (2).C Turn the locking handle (3) until you it clicks.

(fi g. 6)

3.

2.

1.

5.

4.

6.

!The fi lter cartridge can only be inserted when the locking handle (3) is open.Make sure that the fi lter cartridge is positioned correctly and all o-rings are correctly positioned.

3.6 Step 6: Install fi lter-head wall-mount bracket (see fi g. 7)

!

During assembly, note the installation dimensions, bending radii of the hoses and dimensions of the accessories. The system can be operated with the fi lter cartridge in either vertical or horizontal positions. Using the mounting bracket, it should be installed only vertically, with the “UP” arrow on the bracket correctly positioned.

A Attach the space-saving wall mount bracket (1) in place using two matching screws and use two wall plugs (not supplied), depending on the type of wall. Position it in an accessible place to allow for 90° pivoting of the head for easy exchange of the fi lter.

B Engage the fi lter head (2) in the wall mount (1) using the notches (4) on the sides of the fi lter head to connect to the arms of the bracket.

1.

2.

3.

4.

(fi g. 7)

10 ENGLISH

3.7 Step 7: Commissioning

Before use, make sure that you have followed all the steps correctly and all the parts are fi tted. Place a suitable container under the cartridge to catch any leakages.

A Turn on the cold water supply and check the system carefully for any leaks.

B Open the BRITA water dispenser and allow water to run until the fi ltered water runs clear and without any bubbles (at least 1 litre).

4 Replacing the fi lter cartridge

To ensure optimum performance and for hygienic reasons, the fi lter cartridge is be replaced six months after fi rst use, irrespective of usage. Monitor the display on the cartridge indicator at regular intervals and be alert for the audible alarm signal that will sound at the end of the set 180 days.

! Read the Operating and Safety Information (chapter 9) prior to exchange of fi lter.

NO

TE

The fi lter cartridge can be pivoted by 90° in the wall mount bracket for easy removal. When the locking handle is open, the water supply to the cartridge is interrupted, without the need to turn off the isolating valve.

Replacing the On Line A 1000 fi lter cartridge (see fi g. 6):

A Open the locking handle (3).B To release the pressure in the system, fi rst place a suitable

container under the fl ush hose to catch any water, then press the fl ush button (6).

C Remove the exhausted fi lter cartridge (5) from the fi lter head (2).D Insert the new fi lter cartridge (see chapter 3.5 Step 5).E Close the locking handle (3). Open the BRITA water dispenser

and allow water to run until the fi ltered water runs clear and without any bubbles (at least 1 litre).

5 Resetting the electronic cartridge exchange indicator

A Press the DISPLAY button briefl y to activate the display.B Press and hold the START/RESET button for 5 seconds until a

long beep sounds.C The previously set “180” days appears in the display.D The timer starts automatically.

6 Maintenance

Regularly check the fi lter system for leaks. Regularly check the hoses for kinks. Kinked hoses must be replaced.The expected in- service life of the complete fi lter system is fi ve years.

!Prior to exchanging the fi lter system, read the Technical Data (chapter 7) and the Operating and Safety Information (chapter 9).

Regularly clean the outside of the fi lter system with a soft, damp cloth.

! Do not use any abrasive chemicals, cleaning solutions or astringent cleaning agents.

7 Troubleshooting

A No water fl ow

Cause: Water intake closed.Troubleshooting: Open the water intake at the upstream shut-off

valve or by closing the locking handle (3) on the fi lter head (2).

B No or low water fl ow in spite of open water intake

Cause: Mains pressure too low.Troubleshooting: Check mains pressure. If the fault continues,

check the fi lter system and fi lter cartridge and replace if necessary.

Cause: Filter head not mounted in direction of water fl ow.

Troubleshooting: Dismantle fi lter head and install in direction of water fl ow (chapter 3.4).

ENGLISH 11

C Leak

Cause: Screwed connections not fi tted correctly.Troubleshooting: Check mains pressure. Check all screwed

connections in accordance with chapter 3.4.D Incorrect display or incorrect settings on the electronic

cartridge exchange indicator with display

Cause: Buttons pressed in wrong order or wrong buttons pressed.

Troubleshooting: Press and hold the RESET button for 8 seconds.

8 Technical data of the On Line A 1000 cartridge

Operating pressure 1 bar to max. 8.6 bar

Water intake temperature 4°C to 30°C

Ambient tem-perature during

operation 4°C to 40°C

storage/transport –20°C to 50°C

Filtration fl ow rate (acc. to JIS) 2.5 L/min

Rated service fl ow (acc. to NSF Std 42) 60 L/h

Working fl ow range and associated pressure loss 30–180 L/h / 0.2–1.4 bar

Bed Volume 0.23 L

Weight (dry/wet) 0.4 kg/0.9 kg

Rated fi lter capacity 10,000 L

Chlorine reduction NSF 42 Class I (50%)

Particle retention NSF 42 Class I (0.5 μm)

Chlorine reduction DIN EN 14898 Class 1 (>90%)

Dimensions (Width/Depth/Height)

Filter system(fi lter head with fi lter cartridge)

106 mm/92 mm/232mm

Filter cartridge 86 mm/86 mm/224 mm

Installed dimensions (vertical installation with wall mounting)

137 mm/122 mm/232 mm

Operating position Horizontal and vertical

Water inlet connection G3/8"

Water outlet connection G3/8"

System Tested and Certifi ed by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine taste and odor.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Use cold water only. All of the materials used are safe for contact with drinking water. Observe relevant regulations. Read the manual prior to use.

Chlorine reduction

The BRITA On Line Active Direct water fi lter system has been tested according to NSF/ANSI 42 for reduction of chlorine.The concentration of chlorine in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specifi ed in NSF/ANSI 42.While testing was performed under standard laboratory conditions, actual performance of the system may vary.

SubstanceInfl uent challenge

concentrationReduction

Requirement Actual average

reduction

Chlorine 2,0 mg/L 50 % 94,8

Capacity and Flow rate Table based on Chlorine reduction

Water fi lter system On Line Active

Capacity 10000 Liters/2654 gallons

Rated service fl ow 1.0 litres/min

12 ENGLISH

Important Notice: Read this data sheet and compare the capabilities to your actual water treatment needs before purchasing.

PERFORMANCE DATA SHEET

Manufacturer Seller

Brita GmbH BRITA Water Filter Systems

Heinrich-Hertz-Str. 4 Distributors Pty Ltd

65232 Taunusstein Unit 6 22 Narabang Way

Germany Belrose, NSW, 2085

+49-(0) 6128-746-0 Australia

Tel +61 2 9486 4200

Fax +61 2 9486 4222

www.brita.com.au

PRODUCTS

Water Filter Systems

OnLine Active Plus A 1000 Filterhead 0% G 3/8"

USE GUIDELINES

• Minimum operating pressure: 1 bar• Maximum operating pressure: 8,6 bar• Do not allow exposure to temperatures below 4 °C.• Maximum operating temperature: 30 °C• Nominal fl ow rates:

On Line Active Plus A 1000 (60l/h)• This system must be installed according to local plumbing codes

on the cold water line.Replacement CartridgesRefi ll On Line A 1000

• This system requires regular replacement of the fi lter cartridge to maintain proper operation. Varying scale, chlorine, sediment, or organic substance levels may affect replacement frequency.

• Be sure to change the fi lter cartridge at least as indicated in the capacity table (refer to your Instruction Guide) or six monthly which ever occurs fi rst, or whenever you detect a change in taste, odour, or a decrease in fl ow.

• Please ensure that a backfl ow prevention device, meeting the requirements of AS/NZS 3500.1, is installed on the water supply inlet to the fi lter unit.

• Caution: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

ENGLISH 13

SUBSTANCE REDUCTION

The above listed Water Filter Systems have been tested and certifi ed under NSF/ANSI 42 for reduction of chlorine, taste and odour. The performance of this product has been verifi ed and substantiated as the test data summarised below indicates. These substances may not be in your water.

Test Data

Substance GuidelinesAverage Infl uent

ConcentrationMaximum Effl uent

ConcentrationMinimum Percent

RemovalAverage Effl uent

ConcentrationAverage Percent

Removal

Chlorine NSF/ANSI 42 2,1 mg/l 0,05 mg/l 97,4 % 0,05 mg/l 97,6 %

Testing Conditions:Flow Rate: 0,25GPM pH: 7,5+/–0,5Pressure: 60+/–3 psi Temperature: 20+/–3°C

Refer to your Instruction Guide for more specifi c product and warranty information and to avoid contamination from improper handling and installation. Performance will vary based on local water conditions. The substances reduced by this product are not necessarily in your water.

Buyer’s Signature Date

Seller’s Signature Date

This appliance meets the domestic water treatment appliance Standards AS/NZS 3497 and AS/NZS 4348 for the following water treatment process:

Class Treatment type Function Pass

I Microbiological StatusBacteriostatic

Will stop bacteria increasing N/A

II Microbiological TreatmentBacteria removalVirus removalProtozoa removal

Will remove or inactivate bacteriaWill remove or inactivate virusWill remove or inactivate Crypto-sporidium and Giardia

N/AN/AN/A

III Turbidity and particulate reduction Reduces cloudiness N/A

IV Taste and odour reduction Reduces tastes and odours √

V Chemical treatment Decreases chlorine √

LEGEND:

√ = pass

N/A = Not Applicable

14 ENGLISH

III. Important notes

9 Operation and Safety

Protect the On Line Active Direct water fi lter kit from direct sun-light and mechanical damage.Do not assemble near sources of heat and open fl ames. A stop valve must be installed before the fi lter system intake hose.If the water pressure is greater than 8.6 bar, a pressure reducer must be installed in front of the fi lter system.The On Line Active Direct water fi lter kit is only suitable for domes-tic use. Only water of drinking water quality may be used as intake water for the BRITA water fi lter system.The BRITA water fi lter system is only suitable for cold water use within the supply water temperature stated in chapter 8.No microbiologically impaired water or water of unknown quality may be used without appropriate disinfection. If you have a low pressure boiler, make sure you only connect the On Line A 1000 to the cold water supply with the angle valve, and not to the low pressure boiler.

In the event of offi cial water alert:fi lter fi rst, and then boil

If there are offi cial instructions to boil tap water, the fi lter system must be decommissioned. When the requirement to boil water comes to an end, the fi lter cartridge must be replaced and the con-nections cleaned.

Ultimate hygiene

• For hygiene reasons, the fi lter material of the cartridge is sub-jected to a special bacteriostatic treatment with silver. A minute quantity of silver, harmless to health, may be released into the water, within the guidelines of the World Health Organisation (WHO) for drinking water.• It is generally recommended to boil tap water for certain groups of people (e.g. people with weak immune systems, babies). For such groups, this would also apply to fi ltered water.

Optimum use

• BRITA recommends that the fi lter system not be decommis-sioned for a long period. If the BRITA On Line Active Direct system with Active A1000 fi lter is not used for several days (2–3 days), we recommend that the fi lter system be fl ushed by running the volume X indicated in the table below. After stagna-tion periods of over 4 weeks, the fi lter should be fl ushed by run-ning the volume Y or otherwise consider replacing the cartridge if it is near the end of its recommended life. Please also note the maximum usage period of the fi lter cartridge is 6 months.

Flushing volume X after 2–3 days stagnation Flushing volume

On Line A 1000 1 Litre

Flushing volume Y after 4 weeks stagnation Flushing volume

On Line A 1000 10 Litres

• BRITA fi ltered water is designed for human consumption. Use it within 1–2 days.

• The fi lter system must not be opened or dismantled during operation. The fi lter cartridge must not be opened.

• The fi lter system fi lter head is designed for a service life of 5 years counted from the date of installation.

Natural traces

As the fi lter cartridge contains carbon, derived from natural charcoal, as with such natural matter, there may be variations and this can lead to a slight abrasion of small carbon particles into your fi ltered water, noticeable as black dust. These particles have no negative health effects. If ingested, they will not harm the human body. If you should see any carbon particles in the fi ltered water, BRITA recommends fl ushing out the On Line A 1000 fi lter cartridge by running the fi lter tap until the particle deposits are washed out.

ENGLISH 15

IV. BRITA®, quality and satisfaction guaranteed

Correctly dispose of the BRITA cartridgeexchange indicator with display

The BRITA cartridge exchange indicator has an expected useful life of approx. 5 years. At the end of the useful life of the cartridge exchange indicator, remember that it must be disposed of according to the applicable regulations and statu-tory requirements.

Exclusion of liability

BRITA shall not be held liable for any damage, including subsequent damage, arising from the incorrect use of the product.

100% satisfaction: the BRITA Promise

We are confi dent that this BRITA product will meet your demands in terms of quality and performance. If this product does not meet your expectations, your can return it to us within 30 days of the date of purchase for a full refund. You need to call the Customer Service Hotline for your country for a return authorization and postal instructions. To assist us, you will be asked to explain the reasons for your dissatisfaction and provide your proof of purchase (receipt), your phone number and address.This promise is conditional on the installation having been done in complete and correct accordance with all instructions. There shall be no compensation for any costs related to the instal-lation (parts or services) or for damage to fi xtures or equipment or for consequential loss or damage of any nature.

The BRITA service hotline cares

Do you have any questions about your BRITA product?Or on the subject of water fi ltration? Are you looking for your nearest BRITA retailer?Do you want more detailed information about BRITA products?Or about the BRITA company?Want to make the most of one of BRITA’s service offers?Give us a call! You can fi nd the contact details for your BRITA Customer Service team next to your country code on the back of this booklet.Up-to-date information, consumer tips, seasonal competitions, delicious coffee and tea recipes can be found around the clock at www.brita.net AUSTRALIA: www.brita.com.au Call 1300 55 77 62NEW ZEALAND: www.brita.co.nz Call 0800 4 BRITA