MARK SIZE DESCRIPTION VALVE POSITION / OPERATION

V1 12" MAIN DRAIN SHUT OFF

ISSUED: MAY 23, 2006

V2 12" MAIN DRAIN DIVERSION FLOAT VALVE -

V3 12" GUTTER DRAIN SHUT OFF * NORMALLY OPEN

V4 14" STRAINER/PUMP ISOLATION NORMALLY OPEN

V5 14" PRECOAT AIR OPERATED VALVE NORMALLY OPEN/CLOSES DURING PRECOAT-REGENERATION

V6 10" PUMP DISCHARGE CHECK VALVE -

V7 10" PUMP DISCHARGE THROTTLE VALVE NORMALLY OPEN - SET POSITION - RESTRICTS FLOW

V8 10" SUPPLY LINE THROTTLE VALVE NORMALLY OPEN - SET POSITION - RESTRICTS FLOW

V9 10" PRECOAT AIR OPERATED VALVE NORMALLY OPEN/CLOSES DURING PRECOAT-REGENERATION

V10 12" UV SYSTEM ISOLATION VALVE NORMALLY OPEN/CLOSE TO SERVICE UV SYSTEM

V11 10" UV SYSTEM BYPASS VALVE NORMALLY CLOSED/OPEN TO SERVICE UV SYSTEM

V12 10" HEAT SYSTEM DIVERSION VALVE NORMALLY OPEN - SET POSITION - DIVERTS REQ'D FLOW

V13 6" SUPPLY LINE ISOLATION VALVE * NORMALLY OPEN - SET POSITION - RESTRICTS FLOW

V14 6" PUMP ISOLATION VALVE NORMALLY CLOSED/OPEN TO DRAIN POOL

V15 4" PUMP DISCHARGE THROTTLE VALVE NORMALLY OPEN - SET POSITION - RESTRICTS FLOW

V16 6" PRECOAT AIR OPERATED VALVE NORMALLY CLOSED/OPENS DURING PRECOAT-REGENERATION

V17 4" FILTER TANK DRAIN VALVE NORMALLY CLOSED/OPEN TO DRAIN TANK

V18 VACUUM TRANSFER VALVE NORMALLY CLOSED/OPEN TO VACUUM MEDIA

V19 VACUUM DRAIN VALVE NORMALLY CLOSED/OPEN TO FILL TANK

V20 PRE-COAT VENT VALVE NORMALLY CLOSED/OPEN TO FILL TANK

AFTER ALL WORK HAS BEEN COMPLETED, CONTRACTOR TO PROVIDE FILTRATION SYSTEM VALVE TAGS.CONTRACTOR TO PROVIDE VALVE SCHEDULE/CHART FOR ALL FILTRATION SYSTEM VALVES/TAGS.

MARK DESCRIPTION MARK DESCRIPTION

1 COMMAND CENTER (ELEC PROVIDED BY OTHERS) 19 * 14x6 SADDLE TAP (PRECOAT LINE)

2 REGENERATIVE FILTER TANK 20 * 6"∅ FILTER PRECOAT LINE

3 RECIRCULATION PUMP (8"∅ SUCT - 8"∅ DIS) 21 * 12"∅ MAIN DRAIN LINE

4 POOL DRAIN SUCTION PUMP (6" SUCT - 4" DIS) 22 * 12"∅ GUTTER DRAIN LINE

5 HAIR & LINT STRAINER 23 ANTI-VORTEX PLATE

6 * 14X8 ECCENTRIC REDUCER 24 * 10"∅ SURGE TANK SUCTION LINE

7 * 10x8 ECCENTRIC REDUCER 25 * 14"∅ PUMP SUCTION LINE

8 FLOWSENSOR (PADDLEWHEEL W/ SADDLE MOUNT) 26 * 10"∅ PUMP DISCHARGE LINE

9 AUTOMATIC WATER LEVEL CONTROLLER 27 * 10"∅ FILTERED WATER SUPPLY LINE

10 RELOCATED CHEMICAL CONTROLLER (BLUE I TECH) 28 * 10"∅ UV BYPASS LINE

11 BULK CHEMICAL STORAGE 29 * 6"∅ SUPPLY LINE TO DEEP END OF POOL

12 BULK CO2 STORAGE (RENTED BY OWNER) 30 * 6" POOL DRAIN LINE (SUCT)

13 UV TREATMENT CHAMBER 31 * 4" POOL DRAIN LINE (DIS) TO BKWSH TANK

14 UV CONTROL UNIT 32 * PIPE SUPPORTS/HANGERS AS REQUIRED

15 * TEMPERATURE SENSOR 33 * 6"∅ DECK DRAIN LINE (RE-ROUTE W/ SCHED 40)

16 * 10x3 SADDLE TAP/VALVE (PIPING BY OTHERS) 34 * SUMP PUMP (VERIFY EXIST/REPLACE IN-KIND)

17 * CHEMICAL/CO2 INJECTION 35 * MOTOR STARTER/DISCONNECT

18 * CHEMICAL SAMPLING (PROVIDE VALVE) 36 ACCESS LADDER (PROVIDE REMOVABLE GRATING)

* - ITEMS SHOWN ARE TO BE INCLUDED IN THE LABOR PACKAGE BY CONTRACTORALL PIPING TO BE SCHEDULE 80 PVC - UNLESS OTHERWISE NOTED

EXISTING VALVE SCHEDULE

EXISTING FILTRATION EQUIPMENT KEY

LOCATION OF MOTOR STARTER / DICONNECTS &EXISTING HEAT EXCHANGER TO RECONNECT (SEE ELEC/MECH DRAWINGS)

9

11

EXISTING DURAGRATE GRATING TO REMAIN.

REMOVE AND REPLACE EXISTING 4' x 8' x 1/2"

CLEAR PVC SHEETS TO MATCH EXISTING

(TYPICAL ENTIRE TANK)

EXISTING PUMP TO REMAIN

4

V14

31

V15

30

10

35

1

3

12

2

36

REVISE STRUCTURE TO SUPPORT NEW FILTER TANK. SEE DETAIL 5/AP-1.

26

V8

V6 V7

V10

27

14

13

V10 V9

27 20

EXISTING DURAGRATE FOR ENTIRE FILTER ROOM (COLOR TO BE DARK GRAY)

36

EXISTING HINGED CUTOUT @ ALL ACCESS LADDER LOCATIONS -(TYP. FOR 2)

36

1-1/2"

1-1/2"

3/4"

"PULSAR" UNIT. BASIS-OF-DESIGN: REPLACE IN-KIND WITH ALL ACCESSORIES

REMOVE AND DISCARD EXISTING PRESSURE FILTER

EXISTING NEPTUNE BENSON COMMAND CENTER TO REMOVE AND DISCARD

EXISTING VFD CONTROL CABINET TO BE REMOVED AND DISCARDED

REMOVE AND DISCARD EXISTING CO2 WATER CHEMISTRYCONTROL EQUIPMENT

REMOVE AND REPLACE EXISTING UV CONTROL CABINET

UV UNIT TO BE REFURBISHED. SEE SPECIFICATIONS

LOCATION OF LIMIT OF DEMOLITION OF SUPPLY PIPING

LOCATION OF LIMIT OF DEMOLITION OF SUPPLY PIPING

12

ISSUED: MAY 23, 2006

EXISTING MOTOR CONTROL DISCONNECT SWITCH SHALL BE REMOVED BACK TO THE SOURCE OF POWER

NOTED

Project No.

Date:

Scale:

REVISIONS

A P

rofe

ssio

nal C

orp

ora

tion o

f A

rchitects

and P

lanners

DRAWINGS SHALL HAVE PRECEDENCE OVER SCALED DIMENSIONS; CONTRACTORS SHALL VERIFY, AND BE RESPONSIBLE FOR ALL DIMENSIONS AND CONDITIONS ON THE JOB, AND THIS OFFICE MUST BE NOTIFIED OF ANY VARIATIONS FROM THE DIMENSIONS AND CONDITIONS SHOWN BY THESE DRAWINGS

c GARRISON ARCHITECTS EXPRESSLY RESERVES ITS COMMON LAW COPYRIGHT AND OTHER PROPERTY RIGHTS IN THESE PLANS. THESE PLANS ARE NOT TO BE REPRODUCED, CHANGED, OR COPIED IN ANY FORM OR MANNER WHATSOEVER, NOR ARE THEY TO BE ASSIGNED TO ANY THIRD PARTY, WITHOUT

FIRST OBTAINING THE EXPRESS WRITTEN PERMISSION AND CONSENT OF GARRISON ARCHITECTS. WRITTEN DIMENSIONS ON THESE

. SHOP DETAILS MUST BE SUBMITTED TO THIS OFFICE FOR APPROVAL BEFORE PROCEEDING WITH FABRICATION.

713 CREEK ROAD, BELLMAWR, NEW JERSEY 08031 (856) 396-6200

1360

TA

NY

AR

D R

OA

D, S

EW

ELL, N

EW

JE

RS

EY

08

080

GLO

UC

ES

TE

R C

OU

NT

Y IN

ST

ITU

TE

OF

TE

CH

NO

LO

GY

2020 R

EN

OV

AT

ION

S T

O

1360

TA

NY

AR

D R

OA

D, S

EW

ELL, N

EW

JE

RS

EY

08

080

FO

R T

HE

BO

AR

D O

F E

DU

CA

TIO

N O

F T

HE

SP

EC

IAL

SE

RV

ICE

S S

CH

OO

L D

IST

RIC

T A

ND

TH

E V

OC

AT

ION

AL

SC

HO

OL

DIS

TR

ICT

OF

TH

E C

OU

NT

Y O

F G

LO

UC

ES

TE

R

18-40

01-31-2020

AQ

UA

TIC

CO

NS

UL

TA

NT

:E

DW

IN M

. W

AL

LO

VE

R,

III

-A

IA941 W

heatl

an

d A

ven

ue,

Su

ite 3

04

Lan

caste

r, P

en

nsylv

an

ia 1

7603

tel

717.2

95.7

754

APD-1

POOL FILTERROOM - UPPER

LEVELDEMOLITION

1/2" = 1'-0"1

FILTER ROOM LAYOUT : UPPER LEVEL -

EXISTING CONDITIONS & DEMOLTION

REMOVE AND REPLACE EXISTING CO2 STORAGE VESSEL

EXISTING PIPING TO REMAIN

REMOVE AND REPLACE VALVE

EXISTING PIPING TO REMAIN

REMOVE AND REPLACE UV CONTROL CABINET

EXISTING DISCONNECT TO REMAIN FOR REUSE

REMOVE AND REPLACE ALL VALVES INKIND

EXISTING UV UNIT TO BE REFURBISHED

"PULSAR" UNIT. BASIS-OF-DESIGN: REPLACE IN-KIND WITH ALL ACCESSORIES. REPLACE EXISTING PUMP WITH NEW "PENTAIR" PUMP AND RECONNECT CHLORINE AND ACID FEEDS.

UV UNIT TO BE REFURBISHED. SEE SPECIFICATIONS

REMOVE EXISTING VALVES AND REPLACE WITH NEW VALVES OF SIMILAR FUNCTION. TYPICAL FOR ALL WAFER VALVE

REMOVE AND REPLACE EXISTING UV CONTROL CABINET

REMOVE AND DISCARD EXISTING PRESSURE REGENERATIVE FILTER

EXISTING FLANGE: LIMIT OF EXISTING PIPING RENEWAL

EXISTING NEPTUNE BENSON COMMAND CENTER TO BE

REMOVED AND DISCARDED

EXISTING VFD CONTROL CABINET TO BE REMOVED

AND DISCARDED

REMOVE AND DISCARD EXISTING CO2 AND WATER CHEMISTRY CONTROL EQUIPMENT

POOL DRAIN PUMP TO REMAIN

EXISTING EQUIPMENT TO BE REMOVED AND REPLACED BY OTHERS. NO WORK REQUIRED FOR POOL CONTRACTOR

REMOVE AND REPLACE ACRYLIC SHEETING. TYPICAL OVER SURGE AND BALANCE TANK

REPAIR DAMAGED FLOOR GRATING. TYPICAL FOR ENTIRE FLOOR AREA.

REPAIR AND REPLACE DAMAGED GRATING SYSTEM

REMOVE AND REPLACE EXISTING RECIRCULATION PUMP (BELOW)

EXISTING POOL FILL TO REMAIN

GENERAL NOTES 1. ANY DEVIATION FROM THE ORIGINAL CONSTRUCTION DRAWINGS MUST BE APPROVED BY THE ARCHITECT, PRIOR TO ORDERING MATERIALS OR STARTING ANY WORK.

2. CONTRACTOR TO PROVIDE PROTECTION FOR ALL EXISTING TO REMAIN COMPONENTS AND MATERIALS OF THE FILTER ROOM DURING CONSTRUCTION ACTIVITIES. ANY DAMAGETO ANY INTERIOR OR EXTERIOR BUILDING COMPONENTS WILL BE THE POOL CONTRACTOR'S RESPONSIBILITY TO REPAIR.

3. CONTRACTOR WILL BE RESPONSIBLE FOR ANY BRACING, TEMPORARY SUPPORT, AND TEMPORARY WEATHER ENCLOSURES DURING CONSTRUCTION ACTIVITIES. PROVIDESUITABLE BARRICADES AND WARNING SIGNS NEAR WORK AREA TO PROTECT THE STUDENTS AND OCCUPANTS OF THE BUILDING.

4. CONTRACTOR IS TO REMOVE AND DISPOSE OF ALL REFUSE MATERIALS AND EQUIPMENT SCHEDULED TO REPLACED IN A LEGAL MANNER OFFSITE, AS REQUIRED BY LAW.

5. CONTRACTOR IS TO COORDINATE ALL DEMOLITION ACTIVITIES WITH THE FACILITY TO MINIMIZE DISRUPTION OF OTHER WORK IN THE AREA.

6. TRACE ALL CIRCUITS FOR ALL ELECTRICAL POWER AND CONTROL EQUIPMENT TO BE REMOVED BACL TO THE SOURCE AND LABEL ALL BREAKERS WITH VOLTAGE AND AMPERAGESPECIFIC TO EACH CIRCUIT.

A Addendum #1 2/13/20

ISSUED FOR ADDENDUM #1: 2-13-2020

33

30

V13

V3

V3 17 17 16 V12 16 16 V12 16

22 22

28

26

3434

V11

3 6

25

15

20

19

36

V5

5

V4

2323

2424

25

EXISTING 3"Ø TANK OVERFLOW TO EXISTING DRAIN

EXISTING 4"Ø POOL DRAIN LINE TO EXISTING 6"Ø OVERFLOW LINE

EXISTING BACKWASH TANK

29

21

21

27

22

22

V1 V2

V1 V2

MARK SIZE DESCRIPTION VALVE POSITION / OPERATION

V1 12" MAIN DRAIN SHUT OFF NORMALLY OPEN/CLOSE TO DRAIN POOL

V2 12" MAIN DRAIN DIVERSION FLOAT VALVE -

V3 12" GUTTER DRAIN SHUT OFF * NORMALLY OPEN

V4 14" STRAINER/PUMP ISOLATION NORMALLY OPEN

V5 14" PRECOAT AIR OPERATED VALVE NORMALLY OPEN/CLOSES DURING PRECOAT-REGENERATION

V6 10" PUMP DISCHARGE CHECK VALVE -

V7 10" PUMP DISCHARGE THROTTLE VALVE NORMALLY OPEN - SET POSITION - RESTRICTS FLOW

V8 10" SUPPLY LINE THROTTLE VALVE NORMALLY OPEN - SET POSITION - RESTRICTS FLOW

V9 10" PRECOAT AIR OPERATED VALVE NORMALLY OPEN/CLOSES DURING PRECOAT-REGENERATION

V10 12" UV SYSTEM ISOLATION VALVE NORMALLY OPEN/CLOSE TO SERVICE UV SYSTEM

V11 10" UV SYSTEM BYPASS VALVE NORMALLY CLOSED/OPEN TO SERVICE UV SYSTEM

V12 10" HEAT SYSTEM DIVERSION VALVE NORMALLY OPEN - SET POSITION - DIVERTS REQ'D FLOW

V13 6" SUPPLY LINE ISOLATION VALVE * NORMALLY OPEN - SET POSITION - RESTRICTS FLOW

V14 6" PUMP ISOLATION VALVE NORMALLY CLOSED/OPEN TO DRAIN POOL

V15 4" PUMP DISCHARGE THROTTLE VALVE NORMALLY OPEN - SET POSITION - RESTRICTS FLOW

V16 6" PRECOAT AIR OPERATED VALVE NORMALLY CLOSED/OPENS DURING PRECOAT-REGENERATION

V17 4" FILTER TANK DRAIN VALVE NORMALLY CLOSED/OPEN TO DRAIN TANK

V18 VACUUM TRANSFER VALVE NORMALLY CLOSED/OPEN TO VACUUM MEDIA

V19 VACUUM DRAIN VALVE NORMALLY CLOSED/OPEN TO FILL TANK

V20 PRE-COAT VENT VALVE NORMALLY CLOSED/OPEN TO FILL TANK

AFTER ALL WORK HAS BEEN COMPLETED, CONTRACTOR TO PROVIDE FILTRATION SYSTEM VALVE TAGS.CONTRACTOR TO PROVIDE VALVE SCHEDULE/CHART FOR ALL FILTRATION SYSTEM VALVES/TAGS.

MARK DESCRIPTION MARK DESCRIPTION

1 COMMAND CENTER (ELEC PROVIDED BY OTHERS) 19 * 14x6 SADDLE TAP (PRECOAT LINE)

2 REGENERATIVE FILTER TANK 20 * 6"∅ FILTER PRECOAT LINE

3 RECIRCULATION PUMP (8"∅ SUCT - 8"∅ DIS) 21 * 12"∅ MAIN DRAIN LINE

4 POOL DRAIN SUCTION PUMP (6" SUCT - 4" DIS) 22 * 12"∅ GUTTER DRAIN LINE

5 HAIR & LINT STRAINER 23 ANTI-VORTEX PLATE

6 * 14X8 ECCENTRIC REDUCER 24 * 10"∅ SURGE TANK SUCTION LINE

7 * 10x8 ECCENTRIC REDUCER 25 * 14"∅ PUMP SUCTION LINE

8 FLOWSENSOR (PADDLEWHEEL W/ SADDLE MOUNT) 26 * 10"∅ PUMP DISCHARGE LINE

9 AUTOMATIC WATER LEVEL CONTROLLER 27 * 10"∅ FILTERED WATER SUPPLY LINE

10 RELOCATED CHEMICAL CONTROLLER (BLUE I TECH) 28 * 10"∅ UV BYPASS LINE

11 BULK CHEMICAL STORAGE 29 * 6"∅ SUPPLY LINE TO DEEP END OF POOL

12 BULK CO2 STORAGE (RENTED BY OWNER) 30 * 6" POOL DRAIN LINE (SUCT)

13 UV TREATMENT CHAMBER 31 * 4" POOL DRAIN LINE (DIS) TO BKWSH TANK

14 UV CONTROL UNIT 32 * PIPE SUPPORTS/HANGERS AS REQUIRED

15 * TEMPERATURE SENSOR 33 * 6"∅ DECK DRAIN LINE (RE-ROUTE W/ SCHED 40)

16 * 10x3 SADDLE TAP/VALVE (PIPING BY OTHERS) 34 * SUMP PUMP (VERIFY EXIST/REPLACE IN-KIND)

17 * CHEMICAL/CO2 INJECTION 35 * MOTOR STARTER/DISCONNECT

18 * CHEMICAL SAMPLING (PROVIDE VALVE) 36 ACCESS LADDER (PROVIDE REMOVABLE GRATING)

* - ITEMS SHOWN ARE TO BE INCLUDED IN THE LABOR PACKAGE BY CONTRACTORALL PIPING TO BE SCHEDULE 80 PVC - UNLESS OTHERWISE NOTED

EXISTING VALVE SCHEDULE

EXISTING FILTRATION EQUIPMENT KEY

1-1/2"

1-1/2"

3/4"

ISSUED: MAY 23, 2006

ISSUED: MAY 23, 2006

7

6

5

27

21

33

30

4

31

22

26

11

9

25

20

V16

V7

V6

V14

V15

(SEE DTL 6/A2)

EXISTING CONC. EQUIP. PAD @ PUMP & STRAINER TO REMAIN.

EXIST. FRAMING TO REMAIN

REMOVE EXISTING PULSAR EQUIPMENT

2

13

14 1

8

18

16 16 1616 1732

20

27

28

28

34 34

27

22

31

29

27

20

V12V12V11

V10V10

V8

V9

V17

REMOVE AND REPLACE UV CONTROL CABINETS

REMOVE AND DISCARD EXISTING PRESSURE REGENERATIVE FILTER

EXISTING NEPTUNE BENSON COMMAND CENTER TO REMOVE AND DISCARD

EXISTING DISCONNECT TO REMAIN AND BE REUSED

EXISTING UV UNIT TO BE REMOVED AND REFURBISHED. SEE SPECIFICATIONS

REMOVE AND REPLACE ALL VALVES IN KIND

12

515 19

1 10

20

20

2525

28

30 4 31

35

35

V5 V4

V16

V10

V8

V11

V14 V15

NOTE: FILTRATION ELEMENTS HAVEBEEN REMOVED FROM THEELEVATIONS FOR CLARITY

REMOVE AND DISCARD EXISTING CO2 AND WATER CHEMISTRY CONTROL EQUIPMENT

EXISTING VFD CONTROL CABINET TO BE REMOVED AND DISCARDED

EXISTING NEPTUNE BENSON COMMAND CENTER TO BE REMOVED AND DISCARDED

POOL DRAIN PUMP TO REMAIN

NOTED

Project No.

Date:

Scale:

REVISIONS

A P

rofe

ssio

nal C

orp

ora

tion o

f A

rchitects

and P

lanners

DRAWINGS SHALL HAVE PRECEDENCE OVER SCALED DIMENSIONS; CONTRACTORS SHALL VERIFY, AND BE RESPONSIBLE FOR ALL DIMENSIONS AND CONDITIONS ON THE JOB, AND THIS OFFICE MUST BE NOTIFIED OF ANY VARIATIONS FROM THE DIMENSIONS AND CONDITIONS SHOWN BY THESE DRAWINGS

c GARRISON ARCHITECTS EXPRESSLY RESERVES ITS COMMON LAW COPYRIGHT AND OTHER PROPERTY RIGHTS IN THESE PLANS. THESE PLANS ARE NOT TO BE REPRODUCED, CHANGED, OR COPIED IN ANY FORM OR MANNER WHATSOEVER, NOR ARE THEY TO BE ASSIGNED TO ANY THIRD PARTY, WITHOUT

FIRST OBTAINING THE EXPRESS WRITTEN PERMISSION AND CONSENT OF GARRISON ARCHITECTS. WRITTEN DIMENSIONS ON THESE

. SHOP DETAILS MUST BE SUBMITTED TO THIS OFFICE FOR APPROVAL BEFORE PROCEEDING WITH FABRICATION.

713 CREEK ROAD, BELLMAWR, NEW JERSEY 08031 (856) 396-6200

1360

TA

NY

AR

D R

OA

D, S

EW

ELL, N

EW

JE

RS

EY

08

080

GLO

UC

ES

TE

R C

OU

NT

Y IN

ST

ITU

TE

OF

TE

CH

NO

LO

GY

2020 R

EN

OV

AT

ION

S T

O

1360

TA

NY

AR

D R

OA

D, S

EW

ELL, N

EW

JE

RS

EY

08

080

FO

R T

HE

BO

AR

D O

F E

DU

CA

TIO

N O

F T

HE

SP

EC

IAL

SE

RV

ICE

S S

CH

OO

L D

IST

RIC

T A

ND

TH

E V

OC

AT

ION

AL

SC

HO

OL

DIS

TR

ICT

OF

TH

E C

OU

NT

Y O

F G

LO

UC

ES

TE

R

18-40

01-31-2020

AQ

UA

TIC

CO

NS

UL

TA

NT

:E

DW

IN M

. W

AL

LO

VE

R,

III

-A

IA941 W

heatl

an

d A

ven

ue,

Su

ite 3

04

Lan

caste

r, P

en

nsylv

an

ia 1

7603

tel

717.2

95.7

754

APD-2

POOL FILTERROOM - LOWER

LEVELDEMOLITION

1/2" = 1'-0"1

FILTER ROOM LAYOUT : LOWER LEVEL -

EXISTING CONDITIONS & DEMOLITION

1/2" = 1'-0"2ELEVATION A

1/2" = 1'-0"3ELEVATION B

1/2" = 1'-0"4ELEVATION C

A Addendum #1 2/13/20

ISSUED FOR ADDENDUM #1: 2-13-2020

NEW CONTROL PANEL; PAINTED 8'-0" x 4'-0", 1/2" THICK ACRYLIC ON STAINLESS STEEL UNISTRUT.

OUTLINE OF SURGE TANK BELOW GRATED FLOORS

VARIABLE FREQUENCY DRIVE FOR FILTRATION PUMP. INSTALL NEW VFD IN THE SAME LOCATION AS PREVIOUS VFD LOCATION FOR EASY CONNECTION. MOUNT ON STAINLESS STEEL UNISTRUCT.

NEW DEFENDER FILTER. SEE DETAIL 3/AP-1 FROM ORIGINAL COORDINATION DRAWINGS AND MATCH CONFIGURATION OF SUPPORT LEGS TO INTERFACE WITH NEW FILTER, SEE DETAIL 4/AP-1. PROVIDE 4 NEW SUPPORT LEGS AS REQUIRED AND SECURE TO BASE OF STRUCTURE SIMILAR TO ORIGINAL INTENT.

EXISTING SUCTION PIPING TO

REMAIN

NEW SUCTION PIPING

EXISTING RETURN PIPING TO REMAIN

NEW RETURN PIPING

CHLORINE LINE AND ACID/PH LINE TO DROP TO LOWER LEVEL AND CONNECT INTO THE POOL SUPPLY/RETURN LINE WHERE EXISTING CHEMICAL INJECTION LOCATIONS ARE LOCATED. SEE 2/AP-1 FOR CONTINUATION.

EXISTING ACCESS LADDERS TO LOWER LEVEL

EXISTING ACCESS LADDER TO LOWER LEVEL

40

41

37

10

2

EXISTING POOL FILL TO REMAIN AS IS.

CLEAR COMFORT AIR TUBING TO DIFFUSER AT BOTTOM OF SURGE TANK. AIR TUBING TO BE RUN INSIDE PVC PIPE FOR PROTECTION. SEE 2/AP-1 FOR CONTINUATION.

SADDLE TAP IN VERTICAL RETURN PIPE FOR ACCU-TAB AND ACID-RITE FEED PIPING.

MOUNT AIR COMPRESSOR ON STAINLESS STEEL UNISTRUT SHELF ON WALL

VARIABLE FREQUENCY DRIVE FOR POOL DRAIN SUCTION PUMP. MOUNT ON STAINLESS STEEL UNISTRUCT.

14

39

REPLACE UV CONTROLLER

DISCONNECT. SEE PICTURES.

Ø 6

0 15

/16"

ORIGINAL STRUCTURAL NOTES

1. F.G INDICATES FIBERGLASS STRUCTURAL SHAPE (N)F.G. TO BE EXTREN SERIES 625 AS MANUFACTURED BYSTRONGWELL, OR APPROVED EQUAL.

2. COORDINATE BEAM PLACEMENT WITH FILTERLOCATION

3. ALL BOLTS TO BE STAINLESS STEEL4. NEW FILTER TO BEAR DIRECTLY ON BEAMS / CUT AND

REMOVE GRATING AS REQUIRED.5. EXPANSION BOLTS TO BE HILTI KWIK BOLT II STAINLESS

STEEL OR APPROVED EQUAL.

(VERIFY W/ MANUFACTURER)

TANK FOUNDATION

4x1/

4 F.G

. TU

BE

TYPICAL

FOR

4

(N) 6x1/4 F.G.WIDE FLANGE BEAM

(N) 6x1/4 F.G.WIDE FLANGE BEAM

(E) L2x4x1/4

(E) L2x4x1/4

2' -

0"

SU

PP

OR

T P

OS

TS

3' -

9 1

/2"

1' -

0 1

/2"

6' -

10

"

SUPPORT POSTS

4' - 3"FILTER BEARING PAD, TYPICAL FOR 4

CHLORINE AND ACID/PH LINE DROPS FROM LEVEL ABOVE.

CONNECT NEW CHLORINE AND ACID/PH LINES TO EXISTING INJECTION SITES AT THIS LOCATION.

CLEAR COMFORT AIR TUBING / PVC PIPE DROP TO DIFFUSER.

DIFFUSERS TO BE LINKED TOGETHER AND LOCATED BELOW THE GUTTER AND MAIN DRAIN PIPES, FOR BEST RESULTS.

SURGE TANK ACCESS LADDER

3

REPLACE FILTRATION PUMP

42

MARK SIZE DESCRIPTION VALVE POSITION / OPERATION

V1 12" MAIN DRAIN SHUT OFF NORMALLY OPEN/CLOSE TO DRAIN POOL

V2 12" MAIN DRAIN DIVERSION FLOAT VALVE -

V3 12" GUTTER DRAIN SHUT OFF * NORMALLY OPEN

V4 14" STRAINER/PUMP ISOLATION NORMALLY OPEN

V5 14" PRECOAT AIR OPERATED VALVE NORMALLY OPEN/CLOSES DURING PRECOAT-REGENERATION

V6 10" PUMP DISCHARGE CHECK VALVE -

V7 10" PUMP DISCHARGE THROTTLE VALVE NORMALLY OPEN - SET POSITION - RESTRICTS FLOW

V8 10" SUPPLY LINE THROTTLE VALVE NORMALLY OPEN - SET POSITION - RESTRICTS FLOW

V9 10" PRECOAT AIR OPERATED VALVE NORMALLY OPEN/CLOSES DURING PRECOAT-REGENERATION

V10 12" UV SYSTEM ISOLATION VALVE NORMALLY OPEN/CLOSE TO SERVICE UV SYSTEM

V11 10" UV SYSTEM BYPASS VALVE NORMALLY CLOSED/OPEN TO SERVICE UV SYSTEM

V12 10" HEAT SYSTEM DIVERSION VALVE NORMALLY OPEN - SET POSITION - DIVERTS REQ'D FLOW

V13 6" SUPPLY LINE ISOLATION VALVE * NORMALLY OPEN - SET POSITION - RESTRICTS FLOW

V14 6" PUMP ISOLATION VALVE NORMALLY CLOSED/OPEN TO DRAIN POOL

V15 4" PUMP DISCHARGE THROTTLE VALVE NORMALLY OPEN - SET POSITION - RESTRICTS FLOW

V16 6" PRECOAT AIR OPERATED VALVE NORMALLY CLOSED/OPENS DURING PRECOAT-REGENERATION

V17 4" FILTER TANK DRAIN VALVE NORMALLY CLOSED/OPEN TO DRAIN TANK

V18 VACUUM TRANSFER VALVE NORMALLY CLOSED/OPEN TO VACUUM MEDIA

V19 VACUUM DRAIN VALVE NORMALLY CLOSED/OPEN TO FILL TANK

V20 PRE-COAT VENT VALVE NORMALLY CLOSED/OPEN TO FILL TANK

AFTER ALL WORK HAS BEEN COMPLETED, CONTRACTOR TO PROVIDE FILTRATION SYSTEM VALVE TAGS.CONTRACTOR TO PROVIDE VALVE SCHEDULE/CHART FOR ALL FILTRATION SYSTEM VALVES/TAGS.

MARK DESCRIPTION NEW MANUFACTURER NEW MODEL #

1 COMMAND CENTER (TO REMOVE AND DISCARD)

19 14x6 SADDLE TAP (PRECOAT LINE)

2 REGENERATIVE FILTER TANK - NEW

20 6"∅ FILTER PRECOAT LINE

3 RECIRCULATION PUMP (8"∅ SUCT - 8"∅ DIS)

21 12"∅ MAIN DRAIN LINE

4 POOL DRAIN SUCTION PUMP (6" SUCT - 4" DIS)

22 12"∅ GUTTER DRAIN LINE

5 HAIR & LINT STRAINER

23 ANTI-VORTEX PLATE

6 14X8 ECCENTRIC REDUCER

24 10"∅ SURGE TANK SUCTION LINE

7 10x8 ECCENTRIC REDUCER

25 14"∅ PUMP SUCTION LINE

8 FLOWSENSOR

26 10"∅ PUMP DISCHARGE LINE

9 AUTOMATIC WATER LEVEL CONTROLLER

27 10"∅ FILTERED WATER SUPPLY LINE

10 CHEMICAL CONTROLLER

28 10"∅ UV BYPASS LINE

11 BULK CHEMICAL STORAGE

29 6"∅ SUPPLY LINE TO DEEP END OF POOL

12 BULK CO2 STORAGE (RENTED BY OWNER)

30 6" POOL DRAIN LINE (SUCT)

13 UV TREATMENT CHAMBER

31 4" POOL DRAIN LINE (DIS) TO BKWSH TANK

14 UV CONTROL UNIT

32 PIPE SUPPORTS/HANGERS AS REQUIRED

15 TEMPERATURE SENSOR

33 6"∅ DECK DRAIN LINE

16 10x3 SADDLE TAP/VALVE (PIPING BY OTHERS)

34 SUMP PUMP

17 CHEMICAL/CO2 INJECTION

35 MOTOR STARTER/DISCONNECT

18 CHEMICAL SAMPLING

36 ACCESS LADDER

VALVE SCHEDULE FILTRATION EQUIPMENT KEY

1-1/2"

1-1/2"

3/4"

*NEW WORK: REPLACE ALL VALVES IN KIND

REMARKS

37 CHLORINE GENERATOR

38

ADVANCED OXIDATION SYSTEM

39

AIR COMPRESSOR PUMP

40

N/A N/A * TO REMOVE AND REPLACE WITH INDIVIDUAL CONTROLS.

"NEPTUNE BENSON" SP-55-48-2076 * NEW UNIT TO REPLACE EXISTING. SEE SPECIFICATIONS.

"GRISWOLD" 8X8-13/4P * TWO (2) NEW PUMP; INSTALL ONE (1) AND ONE (1) IN RESERVE.

N/A N/A * EXISTING TO REMAIN; NO WORK.

N/A N/A * EXISTING TO REMAIN; TWO (2) NEW BASKETS TO BE SUPPLIED.

"NEPTUNE BENSON" * IF EXISTING REDUCER IS SERVICABLE, NOTIFY ARCHITECT.

"NEPTUNE BENSON"

N/A

N/A * IF EXISTING REDUCER IS SERVICABLE, NOTIFY ARCHITECT.

"SIGNET" 2551 MAGMETER * NEW MAGNETIC FLOW SENSOR.

"NEPTUNE BENSON" WLC200 * NEW UNIT TO REPLACE EXISTING.

"NEPTUNE BENSON" BLU-SENTINEL ES * TO RELOCATE TO NEW PANEL

* BASIS-OF-DESIGN: REPLACE IN-KIND WITH ALL ACCESSORIES

* NOT USED

"PULSAR" SYSTEM 500

* SEE SPECIFICATIONS.

"ETS" SEE SPECIFCATIONS * REBUILD UNIT WITH NEW INTERNAL PARTS.

"ETS" SEE SPECIFCATIONS * TO REMOVE AND REPLACE WITH NEW UNIT.

* NEW

N/A N/A * EXISTING TO REUSE.

N/A N/A * EXISTING TO REUSE.

"NEPTUNE BENSON" N/A * NEW.

"NEPTUNE BENSON" N/A * NEW UNIT WITH FILTER.

N/A * EXISTING TO REMAIN.

N/A * EXISTING TO REMAIN.

N/A

N/A

N/A * EXISTING TO REMAIN.N/A

N/A * EXISTING TO REMAIN.N/A

N/A * EXISTING TO REMAIN.N/A

N/A * EXISTING TO REMAIN.N/A

N/A * EXISTING TO REMAIN.N/A

N/A * EXISTING TO REMAIN.N/A

N/A * EXISTING TO REMAIN.N/A

N/A * EXISTING TO REMAIN.N/A

N/A * EXISTING TO REMAIN.N/A

N/A * AS REQUIRED TO SUPPORT NEW WORK.N/A

N/A * EXISTING TO REMAIN.N/A

N/A * EXISTING TO REMAIN.N/A

N/A * EXISTING TO REMAIN.N/A

N/A * EXISTING TO REMAIN.N/A

SEE SPECIFICATION. * ACCEPTABLE ALTERNATE"ACCU-TAB"

CCW500 * AIR VALVE AND VENTURI INCLUDED IN KIT."CLEAR COMFORT"

87R147-101-N270X * FOR ADVANCED OXIDATION SYSTEM"GAST/JUN-AIR"

* QUANTITY OF TWO (2); FOR SURGE TANK INSERTION.

POOL HYDRAULIC CALCULATIONS - EXISTING

POOL VOLUME 690,200 GALLONS

SURGE TANK VOLUME 8,378 GALLONS

TOTAL DESIGN VOLUME 698,578 GALLONS

5.25 HOUR TURNOVER RATE (VOLUME / 315 MIN.) 2,218 GPM

NOTES:

• POOL CONTRACTOR TO CHECK ALL WELDS OF EXISTING STAINLESS STEELSURGE TANK. REPAIR WELDS FOR STAINLESS STEEL SURGE TANK ASREQUIRED.

• THE MANUFACTURER'S INSTALLATION INSTRUCTIONS SHALL BE STRICTLYFOLLOWED TO PRODUCE FULLY FUNCTIONING PRIMARY SANITATION AND PHCONTROL SYSTEMS.

41

DIFFUSER 1DMBDC900"PENTAIR"

PH CONTROL SEE SPECIFICATION. * ACCEPTABLE ALTERNATE"ACCU-RITE"

"PULSAR" -

42

PH CONTROL SEE SPECIFICATION. * BASIS-OF-DESIGN"PULSAR"

EXISTING F.G. FRAME

NEW 6 x 1/4"WIDE FLANGE F.G. BEAM

NEW 4" Ø x 1/4" F.G. PIPE

NEW 10" x 5" x 3/8" F.G. PLATE 1/2" Ø BOLTS - TYP FOR 4

1 1

/2"

10"

5"

1 1/2"1 1/2"

EXISTING F.G. BEAM

NEW 6 x1/4 WIDE FLANGE F.G. BEAM

NEW F.G. L4 x 4 x 1/4 x 5 LG E.S.

NEW 1/2" Ø BOLTS - TYP FOR 6

NEW 10" x 5" x 3/8" F.G. PLATE

ADHESIVE CONNECTION PER MANUF

NEW 1/2" Ø BOLTS - TYP FOR 4

NEW 4" Ø x 1/4" F.G. PIPE

NEW 10" x 5" x 3/8" F.G. PLATE

NEW 5/8" Ø EXPANSION BOLTS 4" EMBED - TYP FOR 2

ADHESIVE CONNECTION PER MANUF

EXIST 12" SLAB ON GRADE

EXISTING ACCESS LADDERS TO LOWER LEVEL

11

"PULSAR" CHLORINE GENERATOR. BASIS-OF-DESIGN: REPLACE WITH ALL ACCESSORIES

38

"PULSAR" DRY-ACID FEEDER. BASIS-OF-DESIGN: SEE SPECIFICATIONS.

BASIS OF DESIGN: REPLACE EXISTING PUMP WITH NEW "PENTAIR" PUMP; RECONNECT CHLORINE AND ACID FEEDS

FLOW CELL

WATER CHEMISTRY CONTROLLER

WATER LEVEL CONTROLLER

"PULSAR" UNIT CONTROLS

ELECTRICAL OUTLET, TYP. 3

4' -

0"

3' -

0"*PIPING SPACE FOR

POOL HEATINGEQUIPMENTINTERCONNECTIONSUNDER PANEL.

NOTED

Project No.

Date:

Scale:

REVISIONS

A P

rofe

ssio

nal C

orp

ora

tion o

f A

rchitects

and P

lanners

DRAWINGS SHALL HAVE PRECEDENCE OVER SCALED DIMENSIONS; CONTRACTORS SHALL VERIFY, AND BE RESPONSIBLE FOR ALL DIMENSIONS AND CONDITIONS ON THE JOB, AND THIS OFFICE MUST BE NOTIFIED OF ANY VARIATIONS FROM THE DIMENSIONS AND CONDITIONS SHOWN BY THESE DRAWINGS

c GARRISON ARCHITECTS EXPRESSLY RESERVES ITS COMMON LAW COPYRIGHT AND OTHER PROPERTY RIGHTS IN THESE PLANS. THESE PLANS ARE NOT TO BE REPRODUCED, CHANGED, OR COPIED IN ANY FORM OR MANNER WHATSOEVER, NOR ARE THEY TO BE ASSIGNED TO ANY THIRD PARTY, WITHOUT

FIRST OBTAINING THE EXPRESS WRITTEN PERMISSION AND CONSENT OF GARRISON ARCHITECTS. WRITTEN DIMENSIONS ON THESE

. SHOP DETAILS MUST BE SUBMITTED TO THIS OFFICE FOR APPROVAL BEFORE PROCEEDING WITH FABRICATION.

713 CREEK ROAD, BELLMAWR, NEW JERSEY 08031 (856) 396-6200

1360

TA

NY

AR

D R

OA

D, S

EW

ELL, N

EW

JE

RS

EY

08

080

GLO

UC

ES

TE

R C

OU

NT

Y IN

ST

ITU

TE

OF

TE

CH

NO

LO

GY

2020 R

EN

OV

AT

ION

S T

O

1360

TA

NY

AR

D R

OA

D, S

EW

ELL, N

EW

JE

RS

EY

08

080

FO

R T

HE

BO

AR

D O

F E

DU

CA

TIO

N O

F T

HE

SP

EC

IAL

SE

RV

ICE

S S

CH

OO

L D

IST

RIC

T A

ND

TH

E V

OC

AT

ION

AL

SC

HO

OL

DIS

TR

ICT

OF

TH

E C

OU

NT

Y O

F G

LO

UC

ES

TE

R

18-40

01-31-2020

ISSUED FOR ADDENDUM #1: 2-13-2020

AQ

UA

TIC

CO

NS

UL

TA

NT

:E

DW

IN M

. W

AL

LO

VE

R,

III

-A

IA941 W

heatl

an

d A

ven

ue,

Su

ite 3

04

Lan

caste

r, P

en

nsylv

an

ia 1

7603

tel

717.2

95.7

754

AP-1

POOL FILTERROOM - NEW

1/2" = 1'-0"1.1

FILTER ROOM LAYOUT: UPPER LEVEL -

NEW WORK (ALTERNATE)

1/2" = 1'-0"5NEW FILTER FOUNDATION PLAN

1/2" = 1'-0"3ORIGINAL FILTER FOUNDATION PLAN

1/2" = 1'-0"2

FILTER ROOM LAYOUT: LOWER LEVEL -

NEW WORK (BASIS-OF-DESIGN)

1 1/2" = 1'-0"4ORIGINAL TANK FRAMING DETAIL

1/2" = 1'-0"1.2

FILTER ROOM LAYOUT: UPPER LEVEL -

NEW WORK (BASIS-OF-DESIGN)

1/2" = 1'-0"6CONTROL PANEL DETAIL

A Addendum #1 2/13/20