Whispertek™ surface – dual installation guideSpan™ Ideation system

N u reva - W h i s p e r te k d u a l i n sta l l at i o n g u i d e - J a n u a r y 2 0 1 6 Pa ge 2

WHAT YOU’LL NEED

2″ masking tape Straight edge Laser level 3” Roller

Three (3) people to install the surface.

TABLE OF CONTENTSBefore you begin

Step 1 - Aligning the surface

Step 2 - Adhering the surface

Step 3 - Mounting the second surface

3

4

7

12

N u reva - W h i s p e r te k d u a l i n sta l l at i o n g u i d e - J a n u a r y 2 0 1 6 Pa ge 3

WhisperTekTM Surface installationhttp://nureva-span.uservoice.com/knowledgebase/articles/603927

70°F 21°C

Use a pencil to make a 1/4” at the center of each surface.

To avoid cracking, ensure your surfaces have reached room temperature before unrolling. Allow the surface to rest and flatten for 2 to 3 hours before installation.

BEFORE YOU BEGIN

N u reva - W h i s p e r te k d u a l i n sta l l at i o n g u i d e - J a n u a r y 2 0 1 6 Pa ge 4

ST E P 1ALIGNING THE SURFACE

N u reva - W h i s p e r te k d u a l i n sta l l at i o n g u i d e - J a n u a r y 2 0 1 6 Pa ge 5

P R O J E C T E D I M A G E P R O J E C T E D I M A G E

1"

48"

32" SCREEN AREA

OVERALL CENTERSURFACE 1 CENTER SURFACE 2 CENTER

Measure and markUse your laser level to project a line 1” above the projected image.

Mark a 1” vertical line at the center of each projected image and where the two images meet.

Your marks should extend above the line created by your laser level.

N u reva - W h i s p e r te k d u a l i n sta l l at i o n g u i d e - J a n u a r y 2 0 1 6 Pa ge 6

A B

1 2

1 2

AA BC

Align the surface Secure the surface

Person A aligns the top of the surface with the laser level line.

Person B aligns the top and right side of the surface with the laser level line and overall centerline.

Do not remove the adhesive liner from the back of the surface yet.

Person C will tape the entire length of the surface along the top and bottom edges.

N u reva - W h i s p e r te k d u a l i n sta l l at i o n g u i d e - J a n u a r y 2 0 1 6 Pa ge 7

ST E P 2ADHERING THE SURFACE

N u reva - W h i s p e r te k d u a l i n sta l l at i o n g u i d e - J a n u a r y 2 0 1 6 Pa ge 8

C A

6"

SURFACE 1CENTER MARK

STRAIGHT EDGE

Remove tape from one halfPerson A will remove the tape from only the right side of the surface along both the top and bottom edges.

Hold the surface in placeHolding the straight edge vertically, person C will press the surface firmly against the wall approximately 4-6” to the left of the center mark.

N u reva - W h i s p e r te k d u a l i n sta l l at i o n g u i d e - J a n u a r y 2 0 1 6 Pa ge 9

CA CB

Remove the adhesive linerPerson A will pull the surface away from the wall to allow person B to reach where the adhesive liner is scored at the back and remove it from that side of the surface.

N u reva - W h i s p e r te k d u a l i n sta l l at i o n g u i d e - J a n u a r y 2 0 1 6 Pa ge 1 0

1

CC AB

2 3

Begin adhering the surface to the wallStarting from the center point and moving towards the right, person B will begin to press the surface against the wall with overlapping up-and-down strokes to prevent bubbles from forming under the surface.

As person B moves toward the edge of the surface, person A will slowly allow the surface to move back toward the wall.

N u reva - W h i s p e r te k d u a l i n sta l l at i o n g u i d e - J a n u a r y 2 0 1 6 Pa ge 1 1

CAA B

Adhere the second half of the surfaceOnce the first half is adhered, remove the remaining tape and follow the same process to adhere the second half of the surface to the wall.

N u reva - W h i s p e r te k d u a l i n sta l l at i o n g u i d e - J a n u a r y 2 0 1 6 Pa ge 1 2

ST E P 3MOUNTING THE SECOND SURFACE

N u reva - W h i s p e r te k d u a l i n sta l l at i o n g u i d e - J a n u a r y 2 0 1 6 Pa ge 1 3

A B

1 2

SURFACE 1

SURFACE 2

1 2

Align and secure the surfaceRepeat step 1 to align and tape the second surface against the wall. It is important that the edge touching the first screen is aligned as closely as possible.

N u reva - W h i s p e r te k d u a l i n sta l l at i o n g u i d e - J a n u a r y 2 0 1 6 Pa ge 1 4

ALWAYS begin by adhering the side that meets the previous surface.

Adhere the second surfaceFollow all the previous steps to mount the second surface.

N u reva - W h i s p e r te k d u a l i n sta l l at i o n g u i d e - J a n u a r y 2 0 1 6 Pa ge 1 5

Roller both surfacesApply pressure to both the surfaces using the 3” roller to promote proper adhesion.

© 2016 Nureva Inc. All rights reserved. Nureva, Span, WhisperTek and the Span logo are trademarks of Nureva Inc. in the United States, Canada and other countries.