ngi-welding & cutting-part 02
TRANSCRIPT
Safety ExcellenceSafety Excellence
ELECTRODES CONTENTS
Carbon (C)Magnesium (Mg)Silesia (Si)Chrome (Cr)Nobelium (Nb)Titanium (Ti)Cadmium (Ca)Lead (Pb)Iron (Fe)
Zinc (Z)Nickel (Ni)Niobium (No)
Phosphor (P)
Molybdenum (Mo)
Aluminum (Al)
Sulpher (S)
Safety ExcellenceSafety Excellence
WELDING POWDERS
• Magnesium Silicate• Magnesium Oxide• Calcium Silicate• Calcium Oxide• Zirconium Silicate
• Calcium Fluoride• Aluminum Oxide• Silicon Oxide• Zirconium Oxide
Safety ExcellenceSafety Excellence
FUME HAZARDS
• Toxic gases and fumes produced in welding operations, create serious hazards.
• Fumes can be produced mainly from welding of greasy materials.
• All such materials should be degreased and dried before welding.
Safety ExcellenceSafety Excellence
METHODS OF WELDING & FUMES
WELDING PROCESSHAZARDOUS COMPONENTS
Metal arc – mild steelFe, Fluoride
Metal arcCr, Ni
Tungsten Inert Gas (TIG)Weld gases
Safety ExcellenceSafety Excellence
The inhalation of fumes from the welding or cutting of ZINC galvanized metal may result in “ Metal Fume Fever “ which is characterized by:
A raised temperature, aching muscles , shivering and sweating.
The symptoms develop in a few hours after exposure to the fumes and persist for approximately 24 hours.
The welding of brass, bronze and manganese steel generates large quantities of Carbon Monoxide and Carbon Dioxide gases.
The arc welding of iron and steel produces large quantities of fumes consisting of very fine particles of Iron Oxide.
METAL FUME FEVER
Safety ExcellenceSafety Excellence
EXPOSURE LIMIT
In general, an upper exposure limit for welding fumes is 5 mg/m3.
However for certain elements e.g. Cadmium, which may be present in welding fumes, lower limits are set.
Safety ExcellenceSafety Excellence
WORKING IN CONFINED SPACES
• Working in confined spaces is more dangerous due to accumulation of fumes and toxic gases generated by operations being done inside e.g. welding, flame cutting, lead lining, rubber lining, brush and spray painting, molding GRP (fiber glass), use of adhesives, solvents and etc.
Safety ExcellenceSafety Excellence
ARTIFICIAL VENTILATION
- For the purpose of welding fume extraction, a ventilation system could be considered as adequate if providing a minimum of
- Use of electrically powered ventilation for confined spaces is forbidden due to presence of flammable gases.
100 air changes per hour
Safety ExcellenceSafety Excellence
- Welder in a confined space must be accompanied by a person who stays outside and can give assistance.
- Mechanical ventilation should be installed to send out all fumes.
- Do not under any circumstances compressed oxygen for ventilation. Explosion can occur.
WELDING IN CONFINED SPACES
Safety ExcellenceSafety Excellence
Before any work can be allowed to commence in anenclosed space, the following conditions must be met:
. L.E.L. - less than 1%
• Oxygen - more than 20%
• H2S - less than 1 ppm.
• Carbon Monoxide - less than 1 ppm
WELDING/CUTTING IN CONFINED SPACES
Safety ExcellenceSafety Excellence
PRE-OPERATION CHECKS
Check that all tanks, vessels and equipments on which welding, cutting, brazing or soldering work is to be carried out, are free from gases and vapors and sludge.
Safety ExcellenceSafety Excellence
- Fire blankets are to be used to prevent falling sparks on to neibouring areas and equipments like draining pits.
- The work must be suitably screened to prevent sparks and hot metal from flying outside the immediate work area.
PRE-OPERATION CHECKS
Safety ExcellenceSafety Excellence
WELDING SHELTER
1. must Be non-combustible2. must Allow through
ventilation3. must Have interior surface
which minimize the reflection of dangerous radiations.
Safety ExcellenceSafety Excellence
SAFE WORK PRACTICES
• Follow safe Housekeeping principles
• All wooden scraps, Oily rags, flammables should be remove prior to start the work.
Safety ExcellenceSafety Excellence
SAFE WORK PRACTICES
• Remove any butane lighters, matches, or other combustibles from pockets prior to performing work.
• Do not perform
welding with oily clothing.
SHOULD BE REMOVED