ng wdm common data configuration

7/23/2019 NG WDM Common Data Configuration

1/34

1. Preparation for Data Configuration.....................................................................Page 04

2. Creating a Network ...........................................................................................Page 06 3. Backing up NE Database.................................................................................... Page 29

P-0

Confidential Information of Huawei. No Spreading Without Permission

OptiX OSN 9800 Common Data Configuration


2/34

P-1




3/34

P-2




4/34

1st Chapter: Preparations for Data Configuration

This chapter describes the knowledge required for data configuration, including therequirements of computer configuration, how to login to the U2000.

P-3




5/34

Logging In the U2000 Client

Log in the U2000 client to manage NEs by performing management operations onthe U2000 client.

Prerequisites

Before logging in the U2000 client, ensure that the following conditions are met:

The U2000 server is started.

The network communication between the U2000 client and U2000 server

is available.

The network communication between the U2000 server and GNE is

available.

The ports used between the U2000 client and U2000 server are not

blocked by the firewall.

The IP address of the client must be contained in the access control list

(ACL) that is configured on the U2000 server. The default ACL range is the

entire network segment. It is recommended that you set the ACL restriction

range based on the security requirements.

Legitimate U2000 user names and passwords have been allocated.

U2000 licenses have been correctly loaded to the server.

P-4




6/34

2nd Chapter: Creating a Network

This chapter describes the needed operations and configurations when creatingthe network in the iManager U2000.

P-5




7/34

P-6




8/34

The OptiX OSN 9800 supports master-slave subrack management, which unifies the

management of multi-shelf NEs. The master-slave subrack mode saves IP resources and

displays multiple subracks as one NE on the iManager U2000.

The master subrack needs to be created and the slave subracks will be identified through

the master subrack.

The following Master-Slave subrack mode is available:

OptiX OSN 9800 U64 and OptiX OSN 9800 U64 subrack



The Master-Slave subrack mode is not available to OptiX OSN 9800 U64/U32 and OptiX

OSN 8800 T16 / OptiX OSN 6800.

Planning Principles of Master-Slave subrack mode for OptiX OSN 9800 U64/U32:

1+1 redundancy for the CTU board is recommended for the subrack.

The CTU boards in the master subrack and each slave subrack must be the same

software version.

The hub mode (in which one subrack functions as an NE) cannot be upgraded to

the master-slave mode without service interruption.

A slave subrack cannot be upgraded to the master subrack without service

interruption.

P-7




9/34

The OptiX OSN 9800 series equipments do not support the pre-configuration.

Procedure on the U2000: Step 1 Right-click in the blank space of the Main Topologyand choose New>

NE...from the shortcut menu. The Create NEdialog box is displayed.

Step 2 Select required NE from tree structure at left hand pane.

Step 3 Complete the following information: ID, Extended ID, Nameand

Remarks.

Step 4 To create a GNE, proceed to Step 5. To create a non-gateway NE, proceed

to Step 6.

Step 5 Select Gateway from the Gateway Type drop-down list and set the IP

address.

Step 6 Select Non-Gateway from the Gateway Type drop-down list. Select the

GNE to which the NE is associated to from the Gateway drop-down list.

Step 7 In the case of WDM NE, Select the optical NE to which the WDM NE is

associated from theAssociated ONE drop-down list.

Step 8 Enter the NE User and Password.

Step 9 Click OK, the cursor is displayed as "+", click on the blank space of the

physical view and the NE is created.

P-8




10/34

When the U2000 communicates properly with a GNE, you can search for all NEs that communicate with

the GNE by using the IP address of the GNE or the network segment to which the IP address is

associated. Then, you can create NEs in batches. This method is quicker and more accurate than manual

creation. Therefore, the method of creating NEs in batches is recommended.

Procedure on the U2000:

Step 1 Choose File> Discovery> NE...from the Main Menu. The NE Discoverywindow is

displayed.

Step 2 Select the Transport NE Searchtab. Sets the Search Modeas Search for NE.

Step 3 In the Search Domaindialog box, there is a default search domain. If default search

domain is incorrect, clickAddand the Input Search Domaindialog box is displayed.

Step 4 SetAddress typeto IP Address Range of GNE, IP Address of GNE, or NSAP

Address, and enter Search Address, User Name, and Password. Then, click OK.

Step 5 In the Search for NEdialog box, you can perform the following operations:

a. Select Search for NEand click Start Searchto search for all NEs in the selected

domain.

b. Select Create NE after search, and enter NE userand Password. Then, click Start

Search.

c. Optional: Select Upload after createand click Start Search, so that the NE data can

be uploaded to the U2000 after the NE is created.

Step 6 Click Start Search, switch to theAuto Discoveryinterface. Step 7 Optional: If you select Search for NEonly, you can select the NEs, which are not yet

created, in the Resultlist after the search for NEs is complete. Click Createand then the

Createdialog box is displayed. Enter User Nameand Passwordin the Createdialog box, and

then click OK.

P-9




11/34

The OptiX OSN 9800 product series include the OptiX OSN 9800 U64 and OptiX OSN

9800 U32. Applied at the electrical layer, the product series share boards by using unified

software and hardware platforms and can work with the OptiX OSN 8800 T16 and OptiX

OSN 6800 optical subracks in WDM and OTN systems.

The U2000 allocates the WDM equipment into different optical NEs for management. That

is to say, there are electrical subracks (for example, OSN 9800 U64/U32) and optical

subracks (for example, OSN 8800 T16/OSN 6800) in an optical NE. There are four types of

optical NEs. They are WDM_OADM, WDM_OEQ, WDM_OLA and WDM_OTM.

The ONE here can also be viewed as WDM station.

Procedure on the U2000: Step 1 Right-click in the blank space of the Main Topology and choose New>

NE...from the shortcut menu.

Step 2 Select the optical NE type for the optical NE in theAdd Objectdialog box.

Step 3 In the Basic Attributestab, set the attributes of the optical NE.

P-10




12/34


Step 4 Click the Resource Division tab. Select NEs or boards from the IdleOptical NE.

Step 5 Click OK.

Step 6 Click in the blank space of the Main Topology and the ONE icon appears

in the position where you clicked.

To re-allocate the resources of an optical NE that has been created, right-click the optical

NE and choose Object Attribute. Click the Resource Divisiontab, select an NE or a

board from the list on the left, and then click the double-right-arrow button to allocate the

NE or board to the optical NE.

P-11




13/34

To ensure NE data security, only the users with NE user authority can log in to the NEs. An

NE user is able to perform operations on the NEs according to the assigned authority. The

U2000 administrator is advised to create NE users before configuring services. The default

NE user has the monitor level authority. To ensure NE data security, it is recommended that

you assign NE users with different authorities as required.


Step 1 ChooseAdministration> NE Security Management> NE User

Managementfrom the Main Menu.

Step 2 In the NE list on the left, select an NE.

Step 3 ClickAdd and theAdd NE User dialog box is displayed. Step 4 Enter the NE user name in the NE User field.

Step 5 Select the User Level as needed.

Step 6 In the NE User Flag field, select a user type according to the type of the

terminal through which the user logs in to the NE.

Step 7 Enter the password in the New Password field and enter it again in the

Confirm Password field.

Step 8 In the NE Name field, select the NEs that this NE user is allowed to

manage.

Step 9 Click OK.

P-12




14/34

During a new deployment, after the root NE user creates the NE, this user can create

another NE user. You can log in to the NE with the new NE user name.

An NE user cannot log in to or manage an NE at the same time. After you use an NE user

to log in to an NE through a U2000 server, if you use the same NE user to log in to the

same NE through another U2000 server, the NE user is forced to log out from the first

U2000 server.


Step 1 In the Main Topologyview, chooseAdministration> NE Security

Management> NE Login Managementfrom the Main Menu.

Step 2 Select an NE from the NE list to switch its user. Step 3 Click Query to query the current NE user.

Step 4 In the NE Login Management Table, select the NE and click Switch NE

User. In the Switch Current NE User dialog box, enter the User and Password,

and set Offline Switching. If Offline Switchingis selected, the system does not

check the user name and password, and thus later login of the NE may fail, which

causes the NE unreachable by the NMS. Therefore, it is recommended not to select

Offline Switching.

Step 5 Click OK.

P-13




15/34


Step 1 Select the NE whose data you want to configure. Step 2 Choose Manual Configuration and click Next. The Confirm dialog box is

displayed indicating that manual configuration clears the data on the NE side.

Step 3 Click OK. The Confirm dialog box is displayed indicating that manual

configuration interrupts the service on the NE.

P-14




16/34

The master and slave subracks can be queried at the same time without extra operation.

The Slot IDs: The slot IDs of the master subrack are numbered from 1 and increased by degrees.

The slot IDs of slave subracks are of three digital. The hundred digital is the number

of the slave subrack. For example, "103" stands for the slot 3 in the slave subrack 1.


Step 4 Click OK. The Set NE Attribute dialog box is displayed.

Step 5 Set NE Name, Equipment Type, NE Remarks and Subrack Type and

then click Next. The NE slot window is displayed.

Step 6 Optional: Click Query Logical Information to query the logical boards of

the NE.

Step 7 Optional: Click Query Physical Information to query the physical boards

of the NE.

Step 8 Right-click on the slot to add a board. Click Next to display the Send

Configuration window.

Step 9 ChooseVerify and Run as required and click Finish.

P-15




17/34

An OptiX OSN 9800 U64/U32 subrack is supplied by a power supply pool comprising PIU boards.

Based on the physical power supply configuration, a user can configure a visual power supply pool

and manage power consumption using an emulation NE Panel. Short-circuit relationships between PIU boards can be set when a subrack is powered on for the first

time and cannot be modified after the subrack is properly working. Short-circuit relationships cannot

be modified before the subrack is powered off.

For a newly added board, if the total power consumption of the power supply section where the

new board is located is beyond the power supply capability, the board will not be powered on and

no logical board or services can be created for the board.


Step 1 On the U2000, set the short-circuit relationship between PIU boards to be the same

as the actual short-circuit mode.

Select a PIU board. The target PIU boards that can be short-circuited with theselected board are displayed.

Click the dot above a PIU board. The dot indicates that a short-circuit relationship

can be set between the board and the selected board.

ClickApply.

Step 2 Set the input current.

Click the red triangle in the current display box (green). The input current options

are displayed.

Select a current. The current of each power supply can be set to 0 A, 63 A, 100 A,

or 120 A. 100 A and 120 A are available only for short-circuited PIU boards and 0

A is available only for PIU boards that are not short-circuited.

ClickApply.

OptiX OSN 9800 Common Data Configuration P-16



18/34


Step 1 Select the NE whose data you want to upload. Step 2 Choose Upload and click Next. The Confirm dialog box is displayed

indicating that the upload may take a long time.

Step 3 Click OK to start the upload. The Operation Result dialog box is displayed

when the uploading is completed.

Step 4 Click Close.

P-17




19/34

OptiX OSN 9800 can also configure slave subracks they will exist automatically in NMS

when you configure the subrack NE.

In the master/slave subrack mode, the master subrack and its multiple slave subracks are

displayed as one NE in the network management system. They share the same NE ID and

IP address.


Step 1From the upper side of the slot layout in the right pane. Right-click the

subrack and then chooseAdd Slave Shelf from the shortcut menu to display the

Add Subrack dialog box.

Step 2In theAdd Subrack dialog box, input the basic attribute of the slave shelfincluding the Shelf ID and Shelf Name. Select the Shelf Type from the drop-

down list.

P-18




20/34

Choose the corresponding item from the Function Treeto check the relevant board

parameters.

P-19




21/34

The logical and physical wavelengths of a board must be the same; otherwise, services may be

unavailable.


Step 1 In the NE Explorer, select the desired board. Choose Configuration> WDM

Interfacefrom the Function Tree.

Step 2 In theAdvanced Attributestab, select the desiered port.

Step 3 Double-click the Planned Band Typefields and select the required band type.

Step 4 Double-click the Planned Wavelength No./Wavelength (nm)/Frequency (THz),

set the wavelength No, wavelength and Frequency of the board.

Step 5 ClickApply. A dialog box is displayed for confirming the modification, click OK.

Step 6 Another dialog box is displayed for reconfirming the modification, click OK.

FEC types of two connected boards must be the same. Services may be interrupted when the FEC

types of two interconnected boards are not the same. To ensure normal services, correctly set the

FEC type for two interconnected boards.


Step 1 In the NE Explorer, select the desired board. In the Function Tree, choose

Configuration> WDM Interface.

Step 2 Click By Board/Port(Channel)and select Channelfrom the drop-down list.

Step 3 Click theAdvanced Attributestab. Double-click FEC Modeof the desired optical

port and select the FEC type.

Step 4 ClickApply. A dialog box is displayed for confirming the modification, click OK.

P-20




22/34

Creating Fibers in the Synchronization Mode

After the equipment commissioning is completed, the fiber connections might existon the NE. You can synchronize on the U2000 the internal fiber connection data of

the NE with the U2000 side.

Creating Fiber Connections in Graphic Mode

In graphic mode, you can create fiber connections on the Main Topologyor the

Signal Flow Diagramdirectly. This mode is applicable to scenarios where a small

number of fiber connections are to be created one by one.

Creating Fiber Connections in List Mode

In Fiber/Cable Management, you can manage the fiber connections between NEsand inside NEs in a unified manner. In this case, fiber connections can be created in

an easy manner. This mode is applicable to scenarios where a large number of fiber

connections are to be created.

P-21




23/34

The fiber connections include the inter-subrack fiber connections and intra-subrack fiber

connections.


Step 1 Double-click an optical NE on the Main Topology. Click the Signal Flow

Diagram tab.

Step 2 In the Signal Flow Diagram, right-click in the blank area and choose

Create Fiber from the shortcut menu. The cursor is displayed as "+".

Step 3 Select the source board and port and click OK. The cursor is displayed as

"+".

Step 4 Select the sink board and port and click OK.

P-22




24/34


Step 1Click the shortcut icon on the Main Topologyand the cursor is displayedas "+" .

Step 2Click the source NE of the fiber on the Main Topology.

Step 3 Select the source board and source port in the Select Fiber/Cable Source

dialog box displayed.

Step 4 Click OK. The Main Topologyis displayed and the cursor is displayed as

"+" again.

Step 5 Click the sink NE of the fiber in the Main Topology.

Step 6 Select the sink board and sink port in the Select Fiber/Cable Sinkdialog

box displayed.

Step 7 Click OKand enter the attributes of the fiber in the Create Fiber/Cable

dialog box displayed.

Step 8 Click OK. The created fiber is displayed between the source NE and the sink

NE on the Main Topology.

P-23




25/34


Step 1Right-click in the blank space of the Main Topology and choose New>Link from the shortcut menu. The Create Linkdialog box is displayed.

Step 2Select Fiberfrom tree structure at the left-hand pane.

Step 3 Modify the attribute value according to actual requirements at the right-

hand pane.

Step 4 ClickApply. Repeat Step 3 to create another fiber connection.

Step 5 Click OK to complete the settings. The created fiber is displayed between

the source NE and the sink NE on the Main Topology.

OptiX OSN 9800 Common Data Configuration P-24



26/34

Synchronized Fiber/Cable: Indicates the fibers that exist on both the U2000 and NE sides.

U2000 is the same as the fiber data on NEs.

Fiber/Cable on the NE Only: Indicates the fibers that exist only on the NE side.

Fiber/Cable on the NMS Only: Indicates the fibers that exist only on the U2000 side.

P-25




27/34

To do this operation, you must be an NM user with "NE and network administrator"

authority or higher.

Keeping the time consistency between the U2000 and NEs is very important for

troubleshooting and network monitoring. You should set the U2000 time and NE time

before service configuration.

Synchronizing the NE time does not affect services. Before synchronizing the NE time,

verify that the system time on the U2000 server is correct. If you want to change the

system time, exit the U2000 to reset the time, and then restart the U2000.


Step 1 In the NE Explorer, select the NE. Choose Configuration > NE TimeSynchronizationfrom the Function Tree. The Resultdialog box is displayed.

Click Close.

Step 2 Right-click the NE and then choose Synchronize with NM Time. A dialog

box is displayed. ClickYes.

Step 3 The Resultdialog box is displayed. Click Close. In this manner, the NE time

is synchronized with the NMS time immediately.

P-26




28/34

By setting performance monitoring parameters of an NE properly and starting the

performance monitoring for the NE, you can obtain the detailed performance record

during the running of the NE. This facilitates the monitoring and analysis of the NE running

status performed by maintenance personnel.


Step 1 Choose Performance > Set NE Performance Monitoring Time from the

Main Menu.

Step 2 Select NEs from the NE list.

Step 3 Select one or more NEs, and set 15-minute and 24-hour performance

monitor parameters according to the requirement. Step 4 ClickApply and click Close in the Operation Result dialog box.

P-27




29/34

3rd Chapter: Backing up NE Database

After configuring the network, we need to back up the configurations for security.This chapter introduces how to back up the NE database.

P-28




30/34

We can back up the NE database to CF card or to the system control board on the NE side.

The CF card is on the system control board and can be plugged out during thereplacement of system control board.

P-29




31/34

This slide describes how to back up the latest NE (configuration) data to the NMS server or

NMS client as required in case of NE maintenance or upgrade/downgrade.

The FTP/TFTP/SFTP server is configured and the FTP/TFTP/SFTP service is started.

Using the NE Data Backup/Restoration function, we can back up the NE database to

the NMS computer. Also we can recover the NE database from the NMS computer.


Step 1 In the Main Topologyview, chooseAdministration> NE Software

Management> NE Data Backup/Restorationfrom the Main Menu.

Step 2 Right click the device(s) that you want to backup in the NE Viewtable.

Step 3 Select Backup...to open the Backupdialog.

Step 4 Select the option NMS Server or NMS Client to backup the selected

device information. By default the NMS Server is selected. If the NMS Server is

selected, the selected device information is stored on the NMS server.

Step 5 Optional: If the NMS Client is selected, click to select the location

where the device data have to be backed up.

Step 6 Click Start to start the backup operation for the selected device(s). On the

NE Viewtab page, the backup progress is displayed.

Step 7 When the backup operation is successful, the NMS creates the dbf.pkgfile

in the NEName/yyyymmddhhmmss directory. "NEName" indicates the name ofthe NE, "yyyymmdd" indicates the date when the backup is created, and "hhmmss"

indicates the time when the backup is created.

P-30




32/34

Answer:

The system control board, CF card, NMS server and NMS client.

P-31




33/34

P-32




34/34

P-33OptiX OSN 9800 Common Data Configuration

ng wdm common data configuration

Documents