newton waterproofing systems - poulton remedial … · newton waterproofing systems ... lime...

NEWTON WATERPROOFING SYSTEMSProduct Catalogue

100 - Cementitious Products

200 - Deck & Roofing

300 - Horizontal Drainage

400 - Vertical Drainage

500 - Cavity Drain Waterproofing

600 - Flooring Membranes

700 - Liquid Applied Floor Coatings

800 - Damp Proofing

900 - Liquid Primers & Sealers

Pumping

Multi-Use

© John Newton & Co. Ltd.

Issue Date: February 2011

Ln6 (L34)Cl/SfB

Product cAtALoGuE

SYStEM 100 - cEMENtItIouS ProductSNewton System 100 is a comprehensive portfolio of cementitious products which have been introduced into our structural waterproofing range to complement and complete our basement waterproofing designs in areas where the Newton System 500 would not be suitable. Such details include - lift shafts, flat soffits and externally to retained slabs and ring beams.

Newton 101 F Flexible Slurry (cW 101), Page 4Cementitious Flexible Waterproofing Membrane

Newton 102 WaterPlug (cW 102), Page 5Fast Setting Polymer Compound To Seal Leaks

Newton 103 SBr Additive (cW 103), Page 5Waterproof Additive

Newton 106 Lime Inhibitor (Lc1), Page 5Lime Inhibitor for Application to Concrete Surfaces

Newton 107 QuickFillet (cW 107), Page 6Fast Setting Pre-Mix Mortar for Angle Fillets

Newton 108 Stopaq (cW 108), Page 6Unique Swelling Sealant Compound System

SYStEM 200 - dEcK & rooFINGA complete range of externally applied elastomeric high performance liquid membranes and ancillaries for balconies, terraces, flat and inverted roofs, podium decks, car parks and reservoirs. this new portfolio of seamless and robust liquid membranes gives specifiers and specialist waterproofing contractors a quick and cost effective solution to protect external areas from water ingress.

Newton 200 Flexitape (rF 200), Page 7Reinforcing Tape for Newton Liquid Membranes

Newton 201 rubberFlex (rF 201), Page 7Flexible Liquid Waterproofing Membrane

Newton 202 Quickcure (rF 202), Page 8 Curing Accelerant for Newton 201 RubberFlex

Newton 203 thickener (rF 203), Page 8Thixotropic Additive for Newton 201 RubberFlex

Newton 204 thinner (rF 204), Page 9Polyurethane Thinning & Cleaning Agent

Newton 205 colorSeal (rF 205), Page 9UV Colour Stable Polyurethane CoatingNewton 206 PolySpray (rF 206), Page 10Two Component (Hot Spray) Liquid Waterproofing Membrane

SYStEM 300 - HorIZoNtAL drAINAGENewton’s range of HdPP and HdPE horizontal drainage membranes provides comprehensive protection of primary waterproofing layers such as Newton 201 rubberFlex. In addition they can act as a filtration layer and also provide reservoir capabilities for specifiers who are designing green or turf roof projects.

Newton 306 deckdrain (Hd 306), Page 11Newton 310 deckdrain (Hd 310), Page 11Newton 320 reservoir (Hd 320), Page 12

SYStEM 400 - VErtIcAL drAINAGENewton System 400 comprises a range of composite membranes that include a cuspated core of HdPP or HdPE together with a filter fabric that is attached to the core during the manufacturing process. When placed to the retaining wall these membranes protect the primary waterproofing membrane from impact and water pressure, diverting water down to a perforated land drain for removal.

Newton 406 Geodrain (M8), Page 13Newton 410 Geodrain (M18), Page 14

SYStEM 500 - cAVItY drAIN WAtErProoFINGthe professional’s “waterproofing system of choice”, Newton System 500 is an internally applied waterproofing system based upon our range of cavity drain membranes, drainage conduits and sophisticated pumping and control systems. unlike conventional ‘tanking’, Newton System 500 is not attempting the almost impossible and trying to hold water back, but places designed maintainable depressurisation voids at known weaknesses in the structure so that ingressing water is simply captured and diverted out of the property.

Wall MembranesNewton 503 (M5), Page 15Newton 503 Mesh (M11 & M12), Page 15Newton 508 (M1 & M2), Page 16 Newton 508 Mesh (M3), Page 16 Newton 520 (M4 & M13), Page 16

Note: Please check individual product sheets for advice on appropriate fixings and ancillary products. contact our technical department for further information on 020 7237 1217. copies of our BBA certificates, Brochures and data Sheets can be downloaded from www.newton-membranes.co.uk. Products and their specifications can be changed or modified without prior notice. All copy, diagrams, images and Newton tradenames/logos and designs used in this catalogue remain the intellectual property of John Newton and company Ltd. and may not be reproduced without the written permission of the directors of John Newton and company Ltd. Any party who exploits this property may be subject to prosecution.

© John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217

www.newton-membranes.co.uk - [email protected]

Product cAtALoGuE

SYStEM 600 - FLoorING MEMBrANESNewton System 600 is a range of HdPE and HdPP flooring membranes offering a complete damp proof solution for both commercial and domestic flooring applications. As well as providing protection from dampness within the floor, our membranes ‘de-couple’ the floor finish from the substrate preventing damage due to substrate movement and cracking. Newton damp proof membranes can be installed over existing and ‘green’ concrete. In addition our flooring membranes are a popular solution for dealing with inherent hydrocarbons or ground gas problems. Newton flooring membranes can accommodate a variety of finishes including timber floors, screeds and direct tiles.

Flooring MembranesNewton 601 Slimline (M6), Page 17Newton 603 (M23), Page 17Newton 603 Mesh (M24 & M25), Page 18Newton 603 Bonded tile (M7), Page 18

SYStEM 700 - LIQuId APPLIEd FLoor coAtINGSSystem 700 is a range of liquid applied protective and decorative internal flooring products. these products are fast curing and available in a variety of colours, and are typically used for the refurbishment and protection of commercial and domestic floors.

Newton 701 HB (LM 701), Page 19High Build Epoxy Floor Coating

Newton 702 EcoSeal (LM 702), Page 19Highly Resistant Polyurethane Floor Coating

SYStEM 800 - dAMP ProoFINGNewton System 800 is a range of BBA approved damp proof membranes and ancillaries which are quick and clean to install and offer a permanent solution for damp proofing walls. the meshed membranes provide a firm key and impermeable barrier on any damp or deteriorating surface ready for plaster, render or dot & dab plasterboard. the un-meshed Newton 803 is used where insulation requirements dictate the use of a timber or steel frame ready for plasterboard. Quick, clean and proven to work, Newton damp proof membranes offer a permanent and cost effective damp proofing solution.

Damp Proofing MembranesNewton 805 Newlath (M9 & M10), Page 20Newton 803 (M19 & M20), Page 21Newton 803 Newtonite (M16, M21, M22), Page 21

Damp Proofing AncillariesNewton 800 Mesh Plug (A16), Page 22Newton MultiPlug (A1), Page 22Newton 800 cob Plug (A17), Page 22Newton 800 Mastic (A18), Page 23Newton Mesh tape (A25), Page 23Newton overtape (A8), Page 23Newton 800 Profile (A19), Page 23

SYStEM 900 - LIQuId PrIMErS & SEALErSNewton’s high performance range of liquid applied products are used in conjunction with System 200 and 700 liquid membranes. they act as priming agents for a variety of substrates prior to the application of our specialist waterproofing and flooring membranes.

Newton 901 Humidity Primer (PS 901), Page 24Epoxy Primer Suitable for High Humidity Substrate

Newton 902 (PS 902), Page 24Liquid Applied Radon, Gas & Vapour Barrier

Newton 903 Pu Primer (PS 903), Page 25Epoxy Primer for Nonporous Substrate

Newton 904 HP Accelerant (PS 904), Page 25Humidity Primer Accelerant

Newton 906 Mould Stop (PS 906), Page 25Mould Steriliser & Killer



Product cAtALoGuE

SuMP ANd PuMPNewtons have an extensive range of submersible pumps and pumping ancillaries. We supply the highest quality pumps available in each class, for the control of clean ground water, grey water, effluent or sewage.

Clean/Ground Water PumpsNewton NP150 (P1), Page 26Newton NP400 (P2 & P3), Page 26Newton NP750 (P5 & P6), Page 27

Effluent Pumps (Not Sewage)Newton NP400W (P4), Page 27Newton NP750W (P8), Page 27

Sewage PumpsNewton 750 trojan (Vortex) (P9), Page 27Newton Flygt dXG (Grinder) (P14 & P16) Page 28

Specialist PumpsNewton NP400 LLPS (SP1), Page 28

Sewage Lifting Stationtrojan Sewage Pumping System (tr1-tr12), Page 28

Clean/Ground/Effluent Pumping Systemstitan-Pro White (tPW), Page 29titan-Pro Green (tPG), Page 29Newton titan NP150 (t1 & t3), Page 29(clean or ground water only)

Pumping Ancillary ProductsNewton control Panel Pro (cP2), Page 30Newton High Water Level Alarm (PA12), Page 30Newton 1200w Power converter (c1 & c3), Page 30Newton 3000w Power converter (c2 & c4), Page 30

Newton can also provide a wide range of specialist submersible pumps and sump chambers which can be tailor made for site-specific conditions. For further information call our technical department on 020 7237 1217

MuLtI-uSEthe Multi-use section is home to products that are used within more than one of our systems. WaterSeal tape, for example, can be used with System 300, System 400, System 500, System 600 and System 800.

Newton Mesh tape (A25), Page 31Newton overtape (A7, A8, A9), Page 31Newton WaterSeal rope (A6 & A6W), Page 31Newton WaterSeal tape (A5 & A5W), Page 32Newton MultiPlug (A1), Page 32Newton NuSeal Plugs (A2 & A3), Page 32



J o h n N e w t o n L t d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o . u k

NEWTON SYSTEM 100Cementitious Products

WATERPROOFING SYSTEMS OVERVIEW

NEWTON SYSTEM 100 - CEMENTITIOUS PRODUCTSSystem Overview

Newton System 100 is a comprehensive portfolio of cementitious products which have been introduced into our structural waterproofing range to complement and complete our basement waterproofing designs in areas where the Newton System 500 would not be suitable.

Such details include: lift shafts, flat soffits and externally to retained slabs and ring beams.

NEWTON 101F (CW 101)Cementitious Flexible Waterproofing Membrane

Newton 101F is a two-component acrylic modified cementitious coating. It is the ideal product to waterproof and re-surface concrete and masonry. 101F is a hard wearing, seamless waterproofing solution which is very user friendly with simple on-site mixing methods.

Newton 101F is applied in two coats 1mm each to provide a total thickness of 2mm. Each 1mm coat requires a coverage rate of 1.8kg per m² to give a total coverage rate of 3.6kg per m². Newton 101F is supplied in two components of 1 x 25kg tub of powder and 10kg of liquid additive (35kg pack) which will cover 9m² - 10m²

Typical Applications:• Waterproof lining for lift pits, swimming pools etc.• Bathroom and wet areas• Waterproof coating for roofs• Internal application to flat concrete soffits in conjunction with Newton System 500• Slurry application to form waterproof bunds• Lining existing concrete sump chamber• Protection of steels against carbonation and chloride attacks

Page 4



http://www.newton-membranes.co.uk/services/services.aspx?serviceType=9&id=131&catID=10




NEWTON 102 WATERPLUG (CW 102)Fast Setting Polymer Compound To Seal Leaks

Newton 102 WaterPlug is a fast setting, polymer compound that instantly stops running water or seepage through masonry or concrete substrates. It becomes harder and more resistant when subjected to constant water pressure. Newton 102 WaterPlug is a non-shrink material that expands slightly and sets in approximate 2 minutes. Available in 5kg, 10kg or 25kg tubs.

Typical Applications:• Leak sealing prior to tanking with Newton 101F flexible cementitious coating• Sealing of leaks at wall/floor junctions• Sealing of leaking mortar joints• Leak sealing of cracks in masonry or concrete• Repair of construction faults such as honeycombing• Anchoring of bolts or posts• Controlling water ingress during sump installations

NEWTON 103 SBR (CW 103)Waterproof Additive

Newton 103 SBR is a high quality liquid, water-based high solids styrene butadiene polymer latex with high bonding and waterproofing characteristics. It is stable under wet alkaline conditions forming a reinforcing polymer matrix within cementitious mixes. Available in 5kg, 10kg and 25kg

Typical Applications: • Surface waterproofing • Lift shafts• Waterproof screeds • Wall/floor junction fillets

NEWTON 106 LIME INHIBITOR (LC1)Lime Inhibitor For Application To Concrete Surfaces

Newton 106 Lime Inhibitor is applied to concrete surfaces prior to the installation of a Newton System 500 cavity drain membrane waterproofing system to prevent the ‘leaching’ of free lime from the concrete. Primarily designed to be used to new concrete structures, Newton Lime Inhibitor should also be used to treat the following areas: newly formed concrete walls, kickers and underpins, treatment to cut recesses prior to Basedrain installation and as a concrete additive to newly formed sump chambers. Supplied in 1kg units - Newton 106 is a concentrated mix to be added 1 part Newton 106 Lime Inhibitor to 9 parts clean water. Newton 106 should be applied in this 10 litre mix through a course sprayer and will cover a maximum of 100 sq m²

Product Features: • Solvent and caustic free • Easy to use and handle• Non-hazardous (on dilution) • Long term durability • Compatible with alkaline substrates



Page 5





NEWTON 107 QUICKFILLET (CW 107)Fast Setting Pre-Mix Mortar For Angle Fillets

Newton 107 QuickFillet is a fast setting and fast curing mortar with a rapid strength gain used to quickly form 45° angled fillets at junctions between walls and floors or soffits. Newton 107 QuickFillet should be used to form fillets for use with Newton 101F cementitious slurry and can be used to reinforce internal corners ready for Newton liquid applied membranes such as 201 RubberFlex, 206 PolySpray, 205 ColorSeal or 702 EcoSeal. Newton 107 Quick Fillet can also be used to repair substrate prior to the use of Newton System 900 primers.

Newton 107 QuickFillet is supplied in 25kg tubs and when correctly mixed with 3.6 litres of clean water should cover approx 30 linear metres applied in a 25mm x 25mm fillet

Typical Applications:• Creation of angle fillets• Surface repairs to substrate prior to application of Newton System 900

floor primers

NEWTON 108 STOPAQ (CW 108)Unique Swelling Sealant Compound System

Newton 108 Stopaq is a unique swelling sealant compound system which provides a waterproofing solution for the notoriously difficult to seal service pipe penetrations through retaining walls.

Newton 108 Stopaq is supplied in 0.53kg tubes and is applied with a specialist applicator gun. The product cartridge needs to be heated prior to installation by submersing in hot water.

Product Features:• Requires minimal surface preparation• Adheres on wet and dry surfaces• Fast and easy to apply• Has no shelf life and does not harden• Water and gas impermeable• Non toxic and environmentally friendly• Long term protection with no ageing of the product



Page 6



NEWTON SYSTEM 200Deck & Roofing


NEWTON SYSTEM 200 - DECK AND ROOFINGSystem Overview

Newton System 200 is a complete range of externally applied liquid elastomeric membranes for the structural waterproofing of podium decks, balconies and terraces, flat and inverted roofs, car parks, swimming pools, green or turf roofs and reservoirs. This new portfolio of seamless and robust liquid membranes gives specifiers and specialist waterproofing contractors a quick and cost effective solution to protect external areas from water ingress.

NEWTON 200 FLEXITAPE (RF 200)Reinforcing Tape for Newton Liquid Membranes

Newton FlexiTape is a high quality fibreglass reinforcing tape used to strengthen the internal corners of Newton 201 RubberFlex. The tape ensures that the liquid membrane is unaffected by differential movement at the wall/floor junction and strengthens the liquid membrane at the wall/floor junction. FlexiTape is supplied in rolls 150mm x 25m

Typical Applications:• Reinforcement of the wall/floor junction of Newton liquid waterproofing membranes

NEWTON 201 RUBBERFLEX (RF 201)Flexible Liquid Waterproofing Membrane

Newton 201 RubberFlex is a BBA approved single part, cold applied liquid waterproofing product which after polymerisation forms an elastomeric polyurethane membrane which gives the specifier, client and specialist contractor many design and installation benefits. It is UV Stable, able to handle severe building movement and deformations, 100% waterproof while allowing for vapour diffusion, and has excellent resistance to chemical agents (including cleaning fluids). It also has high impact resistance, is highly durable and has excellent adhesion to most substrates. Once primed with either Newton 901 Humidity Primer, Newton 902 Gas Vapour Primer or Newton 903 PU Primer, RubberFlex can be applied to a variety of different substrates including; new and existing concrete, mortar, bricks, steel, glass, tiles and ply to form a seamless and durable waterproof barrier. Available in 5kg, 10kg and 25kg - Application rates 25kg is sufficient to cover 12.5m2 of surface with a 2 coat treatment of 2kgs per m2 providing an overall membrane thickness of 1.9mm (refer to data files for suggested drying times between coats and for use of Newton accelerants) (Specialist application equipment such as spiked rollers are available on request.)

Typical Applications:• Balconies and terraces • Flat and inverted roofs• Podium decks • Car parks• Reservoirs, pond liners and water holding vessels • External waterproofing of basement walls• Green-roof waterproofing membrane



Page 7





NEWTON 202 QUICKCURE (RF 202)Curing Accelerant for Newton 201 RubberFlex

Newton 202 QuickCure is a clear accelerant additive for exclusive use with Newton 201 RubberFlex. The addition of Newton 202 QuickCure to 201 RubberFlex results in 201 RubberFlex being touch dry in 30-60 minutes, (diminishing the risk of damage by rain, wind, etc.), and trafficable within 3-4 hours. The accelerated curing is achieved without any loss in the properties of the 201 RubberFlex, producing a final membrane free of any CO2 “bubbles”. The most significant advantage of using 202 QuickCure is that it allows the 201 RubberFlex to be applied in one coat.

Newton 202 QuickCure is available in 1kg and 2.5kg containers. 1kg of QuickCure is mixed with 10kg of RubberFlex, 2.5kg of QuickCure is mixed with 25kg of Rubberflex

Product Highlights:• Reduction of curing time to allow for completion of project before poor

weather arrives• Ability to apply Newton 201 RubberFlex in one coat - especially applicable in

colder conditions when it would be impossible to lay two coats in one day

NEWTON 203 THICKENER (RF 203)Thixotropic Additive for Newton 201 RubberFlex

Newton 203 Thickener is a clear thixotropic additive for exclusive use with Newton 201 RubberFlex. The addition of Newton 203 Thickener to Newton 201 RubberFlex significantly lowers the viscosity and so allows for its use on sloped and vertical surfaces.

Newton 203 Thickener is added to 201 RubberFlex at a ratio of 1 part Newton 203 to 25 parts 201 Rubberflex. Newton 201 Thickener is supplied in 1kg containers.

Product Highlights:• Produces an even, non-sagging finish to Newton 201 RubberFlex to inclined and

vertical surfaces• Constant regular thickness • No drips• Traditional methods such as including a textile support are not required• Simple to add and mix with Newton 201 RubberFlex



Page 8





NEWTON 204 THINNER (RF 204)Polyurethane Thinning & Cleaning Agent

Newton 204 Thinner is a slow acting blended solvent for use with Newton 201 RubberFlex and Newton 205 ColorSeal. Newton 204 Thinner is used to dilute the polyurethane membrane and is especially useful when Newton 201 RubberFlex is applied by airless spray.

Newton 204 Thinner is also used as a cleaning medium for tools and equipment used during the application of the membrane and it can be also used as a barrier against humidity when having to store product already opened. Newton 204 Thinner is supplied in 4kg, 9kg and 20kg containers.

Typical Applications:• Cleaning of tools and equipment• Increasing viscosity of membranes for application by airless spraying• Sealing of product against moisture in opened containers

NEWTON 205 COLORSEAL (RF 205)UV Colour Stable Polyurethane Coating

Newton 205 ColorSeal is a UV stable, single component, protective and decorative polyurethane resin top-coat that can be transparent or pigmented in RAL colours through the addition of pigment pastes. Newton 205 ColorSeal is an extremely hard wearing and UV stable coating for both outdoor and ventilated indoor applications. Newton 205 ColorSeal is supplied in 4kg, 9kg and 20kg containers.

Coverage: a 4kg pack is sufficient to cover a prepared surface area of 13m2 with the recommended covering of 0.3/m2 providing an overall thickness of 250-400 microns. With a 2 coat application which includes the quartz sand anti-slip layer, coverage will be 8 - 13m2 with the recommended two coat treatment of between 0.15 and 0.2kg m2

Typical Applications:• Heavy traffic areas• Industrial factories, depots and warehouses• Tennis courts and recreational areas• UV colour stable finish to other floor coatings



Page 9





NEWTON 206 POLYSPRAY (PS 206)Two Component (Hot Spray) Liquid Waterproofing Membrane

Newton 206 PolySpray is a two component Polyurethane resin, which cures very fast into an elastic membrane which has the capacity to bridge over fissures. Being spray applied, Newton 206 PolySpray can be applied extremely quickly to very large roofs, balconies, car parks and podium decks. Newton 206 PolySpray is heat activated and is applied with specialist spray equipment with heated hoses is required to apply the product. Please contact us for details of a Newton Specialist Contractor who can install and guarantee this system.

Note: Prior to 206 PolySpray being applied it is critical to prime the substrate with a Newton approved liquid primer.

Newton 206 PolySpray is supplied in two components: Part A - 200kg drum, Part B - 195kg drum

Coverage rates equate to 2kg per m2 giving a membrane depth of 1.7 - 2.0mm

Typical Applications:• Balconies and terraces• Flat and inverted roofs• Podium decks• Green-roof waterproofing membrane• Pond and lake lining• Retaining walls and external elevations of basements



Page 10



NEWTON SYSTEM 300Horizontal Drainage


NEWTON SYSTEM 300 - HORIZONTAL DRAINAGESystem Overview

Newtons range of HDPP and HDPE horizontal drainage membranes provide comprehensive protection of primary waterproofing layers such as Newton 201 RubberFlex and Newton 902 Primer.

In addition they can act as a filtration layer and provide reservoir capabilities for specifiers who are designing green or turf roof projects.

NEWTON 306 DECKDRAIN (HD 306)Externally Applied Horizontal Drainage Membrane

Newton 306 DeckDrain is a component drainage sheet consisting of a non-woven geotextile filter layer thermally welded to a water impermeable HDPP drainage membrane.

It provides outstanding drainage and protection to primary deck/horizontal applied membranes.

Newton 306 DeckDrain comes in rolls which are 2m x 15m with a surface coverage of 30m2 (stud formation diagonal 6mm in depth)

NEWTON 310 DECKDRAIN (HD 310)Externally Applied Horizontal Drainage Membrane

Newton 310 DeckDrain is a component drainage sheet consisting of a non-woven geotextile filter layer thermally welded to a water impermeable HPDE cavity drain membrane.

It has inline 10mm studs which allow for a greater flow rates and a higher load bearing capacity than our diagonal 6mm alternative.

Newton 310 DeckDrain comes in rolls which are 2m x 12.5m with a surface coverage of 25m2



Page 11



NEWTON SYSTEM 300Horizontal Drainage


NEWTON 320 RESERVOIR (HD 320)Externally Applied Horizontal Drainage Membrane

Newton 320 Reservoir is a 20mm studded HDPE studded membrane for use above a primary waterproofing membrane as a part of a green/turf roof structure. The 20mm dimples act as a catchment zone for water so that the plants within the system have stores to draw upon when required. In the event of the 20mm dimples filling, the membrane has overflow holes above the dimples on the flat surface of the drainage sheet.

The 20mm membrane also acts as a robust root barrier.

Newton 320 Reservoir comes in sheets 2.5m x 1.2m covering a surface area of 3m2



Page 12



NEWTON SYSTEM 400Vertical Drainage


NEWTON SYSTEM 400 - VERTICAL DRAINAGESystem Overview

Newton System 400 comprises a range of composite membranes that include a dimpled core of HDPP or HDPE together with a filter fabric that is attached to the core during the manufacturing process. When placed to the retaining wall these membranes protect the primary waterproofing membrane from impact and water pressure, diverting water down to a perforated land drain for removal.

Newton System 400 membranes have either a 6mm or 10mm dimpled core and are mechanically fixed to a retaining wall already treated with the primary waterproofing membrane such as Newton 902 Primer.

System 400 membranes provide drainage protection and are suitable as an externally applied solution to all retaining walls. Where the requirement is for an Environmental Grade to BS8102 or Grade 2 or Grade 3, we would recommend that System 500 be specified instead.

NEWTON 406 GEODRAIN (M8)Externally Applied Drainage Membrane

Newton 406 Geodrain is a component drainage sheet consisting of a non-woven geotextile filter layer thermally welded to a water impermeable HDPP drainage membrane. Newton 406 Geodrain provides outstanding drainage and protection to the outside face of basement walls and under basement rafts, preventing the build-up of water pressure and protecting the structure from aggressive water, chemicals and toxins.

Newton 406 Geodrain comes in rolls which are 2m x 15m with a surface coverage of 30m2 (stud formation diagonal 6mm in depth). Use Newton Geodrain Profile (A15) in 2m lengths to cap the product at top.

Typical Applications:• As the drainage layer of an externally applied waterproofing system when used

in conjunction with sheet applied or liquid applied external tanking membrane to BS8102:2009

• Protection of the structure from aggressive chemicals in the ground water• To prevent the build-up of ground water to the outside of retaining walls and rafts



Page 13



NEWTON SYSTEM 400Vertical Drainage


NEWTON 410 GEODRAIN (M18)Externally Applied Drainage Membrane

Newton 410 Geodrain is a component drainage sheet consisting of a non-woven geotextile filter layer thermally welded to a water impermeable HDPE drainage membrane. Newton 410 Geodrain provides outstanding drainage and protection to the outside face of basement walls, preventing the build-up of water pressure and protecting the structure from aggressive water, chemicals and toxins.

Newton 410 Geodrain comes in rolls which are 2m x 12.5 with a surface coverage of 25m2 (in-line studs 10mm in depth)

Typical Applications:• As the drainage layer of an externally applied waterproofing system when used

in conjunction with sheet applied or liquid applied external tanking membrane to BS8102:2009

• Protection of the structure from aggressive chemicals in the ground water• To prevent the build up of ground water to retaining walls• Protection of the structure from aggressive chemicals in the ground water



Page 14



NEWTON SYSTEM 500Cavity Drain Waterproofing


NEWTON SYSTEM 500 - CAVITY DRAIN WATERPROOFINGSystem Overview

The professional’s “waterproofing system of choice”, Newton System 500 is an internally applied waterproofing system based upon our range of cavity drain membranes, drainage conduits and sophisticated pumping and control systems.

Unlike conventional ’tanking’, Newton System 500 is not attempting the almost impossible and trying to hold water back, but places designed maintainable depressurisation voids at known weaknesses in the structure so that ingressing water is simply captured and diverted out of the property. Newton recommends that our structural waterproofing systems are installed by one of our Nationwide Network of Newton Specialist Basement Contractors who have been trained by Newton and can offer full PI on design and insured backed guarantee on the installation.

NEWTON 503 (M5)3mm Cavity Drain Membrane for Basement Walls, Floors & Vaulted Soffits

Newton 503 is a BBA approved cavity drain waterproofing membrane suitable for use internally to retaining walls, vaulted soffits and floors.

Newton 503 is a flexible HDPE membrane which at 0.5mm in thickness provides a low profile drainage solution within the Newton Cavity Drain membrane range.

Newton 503 (M5) is available in rolls 2m x 20m - 40m2

NEWTON 503 MESH (M11 & M12)3mm Meshed Cavity Drain Membrane for Basement Walls & Vaulted Soffits

Newton 503 Mesh is a BBA certified meshed membrane suitable for use as a waterproofing membrane when used below the ground as part of Newton System 500.

With its 3mm stud, Newton 503 Mesh is just 3.5mm in overall thickness, and is the preferred meshed membrane where space is of a premium. Its meshed surface provides an excellent ’key’ for lime mortars, renders, plasters or dabbed plasterboard. When using our Newton 503 Mesh it is essential to use Newton MultiPlug or Newton NuSeal with WaterSeal Rope as a means of achieving a waterproof seal.

Newton 503 Mesh is available in roll sizes 1m x 20m - 20m2 (M12) and 2m x 20m - 40m2 (M11)



Page 15



NEWTON SYSTEM 500Cavity Drain Waterproofing


NEWTON 508 (M1 & M2)8mm Cavity Drain Membrane for Basement Walls, Floors & Vaulted Soffits

Newton 508 is our high quality BBA cavity drain waterproofing membrane suitable for use internally below the ground to retaining walls, vaulted soffits and floors. Newton 508 is our flagship membrane and one of the most specified cavity drain membrane in the UK. The 0.7mm thick HDPE product allows for large industrial loads to be applied and the in line studs allow for quick installation with minimal surface preparation.

Newton 508 is available in roll sizes 2.4m x 20m - 48m2 (M1) and2m x 20m - 40m2 (M2)

NEWTON 508 MESH (M3)8mm Meshed Cavity Drain Membrane for Basement Walls, Floors & Vaulted Soffits

Newton 508 Mesh is a BBA approved meshed cavity drain waterproofing membrane, suitable for use internally below the ground to retaining walls and vaulted soffits. Newton 508 Mesh is typically used where space prevents the use of a dry-lining frame or block wall as the wall finish or where a direct rendered or plastered finish is preferred. The ability to apply direct finishes to the product give the professional waterproofing designer flexibility to use the system in convoluted or confined basement areas where space is at a premium or where the original contours (features) of the property wish to be retained.

Newton 508 Mesh (M3) is available in rolls 2m x 20m - 40m2

Typical Applications• New build basements• Existing basements in listed buildings as it is deemed reversible• Rail and road tunnels• Underpavement vaults/ceilings or coal holes

NEWTON 520 (M4 & M13)20mm Cavity Drain Membrane for Basement Floors

Newton 520 is a BBA approved cavity drain membrane suitable for use above basement floor areas. The 20mm studded membrane allows for a massive flow rate to pass underneath the membrane and is specified where floor areas are of questionable quality or where it is anticipated that there may be a risk of severe water penetration.

Newton 520 is available in roll sizes 2m x 20m - 40m2 (M4) or 2m x 10m - 20m2 (M13)

Typical Applications

• Applied to existing and new slabs which are of questionable quality



Page 16



NEWTON SYSTEM 600Flooring Membranes


NEWTON SYSTEM 600 - FLOORING MEMBRANESSystem Overview

Newton System 600 is a range of HDPE and HDPP flooring membranes offering a complete damp proof solution for both commercial and domestic flooring applications. As well as providing protection from dampness within the floor, our membranes ‘de-couple’ the floor finish from the substrate preventing damage due to substrate movement and cracking. Newton damp proof membranes can be installed over existing and ‘green’ concrete.

In addition our flooring membranes are a popular solution for dealing with inherent hydrocarbons or ground gas problems. Newton flooring membranes can accommodate a variety of finishes including timber floors, screeds and direct tiles.

NEWTON 601 SLIMLINE (M6)Flat Loose Laid High Grade Flooring Membrane

Newton 601 Slimline is a high-grade flooring membrane used primarily for isolating moisture sensitive flooring from dampness in the floor slab, but can also be used as the floor membrane as part of Newton System 500 when the survey has ascertained that no risk of water entering through the body of the slab exists.

Newton 601 Slimline allows for the installation of sensitive flooring to be laid above ’green’ still curing concrete as soon as the concrete is walkable, usually two days, significantly reducing project times. With a loading capability of over 1000kN/m2, Newton 601 Slimline is able to resist very high compressive loading and is suitable for use as a high load DPC within structural block walls, especially when used to connect the wall and floor membranes within Newton System 500. Newton 601 Slimline is made from HDPP and is the thinnest profile membrane within the Newton floor membrane portfolio.

Newton 601 is available in rolls 2.07m x 20m - 40m2 (M6)

NEWTON 603 (M23)3mm Loose Laid Flooring Membrane

Newton 603 is suitable for use above new and existing floors. The 3mm studs allow for pressure equalisation of dampness within the floor below allowing for dissipation at room perimeter and subsequent drying of the floor. The studs also give slight compression to footfall making the floor very responsive and comfortable and ideal as the floor membrane for performance sports floors. Newton 603 uncouples the floor finish from the substrate so that movement is not transferred to the floor finish above. The membrane also bridges small cracks allowing for quick floor installation above less than ideal substrate.

Newton 603 is available in rolls 2m x 20m - 40m2 (M23)



Page 17



NEWTON SYSTEM 600Flooring Membranes


NEWTON 603 MESH (M24 & M25)Loose Laid 3mm Flooring Membrane with Meshed Surface

Newton 603 Mesh is high grade flooring membrane with an installation height of 3.0mm. The white HDPE cuspated core has a polyethylene mesh above allowing for adhesion of the floor finish to the membrane.

Newton 603 Mesh is loose laid above the substrate and is therefore uncoupled from the floor ensuring that the floor finish is not affected by movement or cracking of the substrate. If a bonded surface to the substrate is required, use Newton 603 Bonded Tile instead.

Newton 603 Mesh is available in rolls 1m x 20m - 20m2 (M24) and 2m x 20m - 40m2 (M25)

NEWTON 603 BONDED TILE (M7)3mm Bonded Flooring Membrane for Tiles & Slabs

Newton 603 Bonded Tile is a multi-core HDPE membrane specifically designed to provide a bonded waterproof substrate with a good key for flooring systems. Newton 603 Bonded Tile can be used as a waterproofing membrane when used below the ground as part of Newton System 500 when the survey has ascertained that there is no risk of water entering through the body of the slab.

With its 3mm stud, Newton 603 Bonded Tile is just 3.5mm in overall thickness. Its high quality geofabric welded surface provides an excellent ’key’ for tiling grouts and the textile underside gives superb adhesion to floors.

Newton 603 Bonded Tile is available in rolls 1m x 30m - 30m2 (M7)



Page 18



NEWTON SYSTEM 700Liquid Applied Floor Coatings


NEWTON SYSTEM 700 - LIQUID APPLIED FLOOR COATINGSSystem OverviewSystem 700 is our range of liquid applied protective and decorative internal flooring products. These products are fast curing and available in a variety of colours, and are typically used for the refubishment and protection of commercial and domestic floors.

NEWTON 701 HB (LM 701)High Build Epoxy Floor Coating

Newton 701 HB is a two-component solvent free water based epoxy resin based floor coating developed to provide protective and decorative properties to concrete, steel and other substrates. The material is supplied as a two pack system comprising pre- weighed amounts of base and curing agent. After mixing together, an easily applied chemical and abrasion resistant finish is produced. This acts as a waterproof, tough, chemical resistant floor coating or as an internal lining for concrete or steel storage tanks containing oils, chemicals, water, etc. It is particularly suitable for chemical bunds.

Typical Applications:• Food preparation areas • Breweries• Industrial units • Warehouses • Garages • Below ground structures where Newton drainage conduits are utilised

NEWTON 702 ECOSEAL (LM 702)Highly Resistant Polyurethane Floor Coating

Newton 702 EcoSeal is a two component, solvent free, high performance Aliphatic Polyurethane resin which provides a hard yet flexible floor coating, with very high abrasion and chemical resistance. It provides excellent surface protection to floorings exposed to high wear and traffic. Newton 702 EcoSeal is supplied as a transparent coating for use above coloured bases such as Newton 701 HB or it can be coloured on site with RAL colours through the addition of pigment pastes and used above a suitable Newton primer as the stand-alone floor finish. The total absence of solvents allows for application in unventilated indoor areas. Newton 702 EcoSeal cures to a UV stable gloss finish.

Typical Applications:• Heavy traffic areas• Industrial factories, depots and warehouses• Indoor tennis courts and recreational areas• Hard wearing finish to other floor coatings• Indoor car parks



Page 19



NEWTON SYSTEM 800Damp Proofing


NEWTON SYSTEM 800 - DAMP PROOFINGSystem Overview

Newton System 800 is a range of BBA approved damp proof membranes and ancillaries which are quick and clean to install and offer a permanent solution for damp proofing walls.

Newton 805 Newlath and Newton 803 Newtonite meshed membranes provide a firm key and impermeable barrier on any damp or deteriorating surface ready for plaster, render or dot & dab plasterboard.

The un-meshed Newton 803 is used where insulation requirements dictate the use of a timber or steel frame ready for plasterboard. Quick, clean and proven to work, Newton damp proof membranes offer a permanent and cost effective damp proofing solution.

NEWTON 805 NEWLATH (M9 & M10)5mm Meshed Damp Proofing Membrane

Newton 805 Newlath (formerly Newlath 2000) is a BBA approved composite damp proofing membrane comprising of high density polypropylene membrane with a rot-proof polythene mesh heat welded during the manufacturing process to the surface of one side. The meshed surface creates a mechanical key to allow the membrane to be plastered, rendered or to receive dot & dab plasterboard. Newlath can be applied internally as a means of dealing with all forms of dampness inherent in structures and externally to properties suffering from driving and penetrating moisture.

With over two million metres of Newton 805 Newlath installed nationally, Newlath is a cost effective and permanent method of dealing with dampness. Typical Applications• Internally for dealing with rising damp, salts and contaminants within existing

structures.• Externally for protection of brick and masonry structures from driving and

penetrating moisture • Treating dampness in listed buildings as the system is deemed removable and

reversible and is sympathetic to the building fabric.• Applied to timber frame properties which require a rendered finish.

Newton 805 Newlath is available in rolls 1.5m x 10m - 15m2 (M9) and 2m x 20m - 40m2 (M10)



Page 20





NEWTON 803 (M19 & M20)Non-Meshed Damp Proofing MembraneNewton 803 is a non-meshed damp proofing membrane for use above the ground. It can be used as an alternative to Newton 803 Newtonite and 805 Newlath where a meshed surface is not required as a surface for direct plastering or rendering. Newton 803 is typically used where the wall finish to the damp-proof membrane is timber battens, a dry-lining frame or block wall.

Newton 803 is 0.5mm thick and has a pattern of raised 3mm studs. The studs face the wall and create air channels that allow for vapour equalisation to take place between the membrane and the wall.

Newton 803 is available in roll sizes 2m x 20m - 40m2 (M20) and 1m x 10m - 10m2 (M19)

NEWTON 803 NEWTONITE (M16, M21, M22)3mm Meshed Damp Proofing Membrane

BBA approved Newtonite provides a firm key and impermeable barrier on any damp or deteriorating surface where direct bonding is not possible. Even poor and random substrates can easily receive Newtonite.

Newtonite presents a physical barrier between the old surface and the new internal finish. Unlike many systems it can be punctured when new wall fixings are required. Holes drilled through the material must however be well sealed with Newton Mastic to stop any dampness bridging between the existing and new surface.

Newtonite 803 is available in roll sizes 1m x 10m - 10m2 (M16), 1m x 20m - 20m2 (M21) and 2m x 20m - 40m2 (M22)



Page 21





NEWTON 800 MESH PLUG (A16)Above ground the Newton 800 Mesh Plug can be used internally and externally to secure Newton meshed membranes: 805 Newlath and 803 Newtonite. Use a 7mm SDS drill bit to drill through membrane and substrate prior to hammering home fixing plug. Once the hole is drilled it should be primed with Newton Mastic sealant to prevent dampness tracking back along the plug.

Size (Width x Length) 7mm x 50mmQuantity Per Bag 250

NEWTON MULTIPLUG (A1)Newton MultiPlug is used with Newton 803. Drill a 10mm hole through the 803 membrane and hammer home with a club hammer. The MultiPlug can take a 5mm dia screw to allow the fixing of battens and dry-lining frames and the Newton Helifix Wall Tie without breaching the membrane.

MultiPlug Pins are sold separately.

NEWTON 800 COB PLUG (A17) In above ground situations, the Newton Cob Plug is used with 803 Newtonite and 805 Newlath membranes. The Newton Cob Plug has an expanding stem which provides effective anchorage in a wide range of base materials. Larger sizes of Newton Cob Plug can be sourced on request.

The ancillaries used below are used with the three damp-proofing membranes that are included within Newton System 800. Newton 803 is a plain membrane used where a dry-lining frame or a block wall is to be used as the wall finish. 803 Newtonite and 805 Newlath are meshed membranes used where a surface key is required for direct plastering, rendering or dot and dabbing to the wall membrane is required. Please read the membrane product data sheets for more information.

Membrane Fixing Plug Jointing Tape Sealing Drilled Hole Plaster Stop Repairs803 MultiPlug Newton Overtape Not Required Not required Newton Overtape803 Newtonite 800 Mesh Plug Newton Mesh Tape Newton 800 Mastic Newton 800 Profile Newton Mesh Tape

805 Newlath 800 Mesh Plug Newton Mesh Tape Newton 800 Mastic Newton 800 Profile Newton Mesh Tape

Size (Width x Length) 10mm x 57mm Quantity Per Bag 100

Size (Width x Length) 7mm x 90mm Quantity Per Bag 50



Page 22





NEWTON 800 MASTIC (A18) Newton Mastic is used with 805 Newlath and 803 Newtonite. It is used to prime the plug hole prior to the fixing plug being hammered home, which serves to stop any ‘bridge’ happening between the damp or stained surface and the new surface. Newton Mastic is also used for sealing around protrusions.

Unit of Sale 0.38 litre tube

NEWTON MESH TAPE (A25)Newton Mesh Tape is used to joint 803 Newtonite and 805 Newlath membranes as well as for repairs to the membrane and for sealing around protrusions. The meshed surface gives a good key for renders and plasters.

Size (Width x Length) 100mm x 10m Unit of sale Single units

NEWTON OVERTAPE (A8)Newton Overtape is used for the jointing of Newton 803 as well as for repairs to Newton 803 and to seal around protrusions to the membrane.

NEWTON 800 PROFILE (A19) Newton Profile can be used with 803 Newtonite and 805 Newlath. It serves as a plaster stop, guaranteeing that the plaster/render will stop short of the floor.

Size 2m lengthsUnit of Sale Single units

Size (Width x Length) 100mm x 20m Unit of sale Single units



Page 23



NEWTON SYSTEM 900Liquid Primers & Sealers


NEWTON SYSTEM 900 - LIQUID PRIMERS & SEALERSSystem Overview

Newton’s high performance range of liquid applied products are used in conjunction with System 200 and 700 liquid membranes. They act as priming agents for a variety of substrates prior to the application of our specialist waterproofing and flooring membranes.

NEWTON 901 HUMIDITY PRIMER (PS 901)Epoxy Primer Suitable for High Humidity Substrate

Newton 901 Humidity Primer is a solvent free two part epoxy resin coating typically used as a primer for Newton high performance liquid applied or sprayed roofing and flooring products. Newton 901 Humidity Primer would be chosen as the primer coating where the substrate contains humidity levels in excess of 4%. Newton 901 Humidity Primer is also used to prepare the wall/floor junction prior to the installation of Newton Baseboard.

Application

Mix Part A - Epoxy Resin with Part B - Hardener thoroughly with a electric paddle mixer for 2 min until a milky uniform colour is achieved. (pot life of approx 30 minutes)

Application rate is 0.3 kg per m2 dependent on the quality of the substrate. Newton 901 Humidity Primer is supplied in 5kg, 10kg and 20kg components.

NEWTON 902 (PS 902)Liquid Applied Radon, Gas & Vapour Barrier

Newton 902 is a single component high performance elastomeric liquid rubber membrane specifically designed for providing a radon, gas and vapour barrier to vertical and horizontal surfaces. Newton 902 is a cost effective vapour barrier material which can easily be applied via a stiff brush, roller or airless sprayer to a variety of different substrates including concrete, mortar/brick, ceramics, steel or aluminium.

Pre-dampen nonpourous substrates prior to the application of the first coat.

Application

902 can be applied in 1 coat at 0.3kg per m2 as a primer for other Newton liquid membranes or as a gas and vapour barrier with a 2 coat application totalling 0.7kg m2 or as a waterproofing membrane to vertical surfaces with a combined 2 coat total of 1kg per m2.

Newton 902 is supplied in 5kg, 10kg and 20kg tubs.



Page 24



NEWTON SYSTEM 900Liquid Primers & Sealers


NEWTON 903 PU PRIMER (PS 903)Epoxy Primer for Nonporous Substrate

Newton 903 PU Primer is used for priming non-absorbent substrates, prior to application of Newton high performance liquid applied roofing and flooring products.

It should be chosen as the primer where the substrate is nonporous such as ceramic, steel, glass, marble, polished concrete etc.

Newton 903 PU Primer can be applied with roller, brush or cloth to a ratio of 0.1kg per m2

Newton 903 PU Primer is supplied in units 4kg, 9kg or 20kg

NEWTON 904 HP ACCELERANT (PS 904)Humidity Primer Accelerant

Newton 904 HP Accelerant is a clear accelerant additive for exclusive use with Newton 901 Humidity Primer. The addition of Newton 904 HP Accelerant to Newton 901 Humidity Primer results in the primer being cured in 1 to 2 hours (diminishing the risk of alteration by rain, wind, etc.). The accelerated curing is achieved without any loss in its properties or changes in the chemical structure of the primer.

Newton 904 HP Accelerant is supplied in 1kg units and has been designed to be added to a 20kg unit of Newton 901 Humidity Primer. Add the 1kg unit of Newton 904 HP Accelerant to the 20kg unit of the 901 Humidity Primer once both parts A and B have been already mixed. Totally mix and homogenise both products together.

Note: After adding 904 HP Accelerant to the 901 Humidity Primer the pot life is shortened to only 20-30 minutes and the combined product cannot be reused.

NEWTON 906 MOULD STOP (PS 906)Mould Steriliser & Killer

Newton 906 Mould Stop can eradicate mould in four easy steps. It is simple to use and as well as killing dangerous mould it prevents regrowth and eliminates musty odours.

Newton 906 Mould Stop is suitable for walls, ceilings, skirting boards, window reveals, uPVC window and door frames.

906 Mould Stop kit contains: 1 litre of Mould Stop Steriliser and Killer Spray, 1 x safety glasses, 1 x pair of disposable gloves, 1 x sponge and 2 x 100ml Mould Stop Paint Additive.

Once mixed Newton 906 Mould Stop will treat between 10 and 15m2



Page 25



NEWTON SUMP AND PUMPPumping Product Range


NEWTON SUMP AND PUMPSystem Overview

Newtons have an extensive range of submersible pumps and pumping ancillaries. We supply the highest quality pumps available in each class, for the control of clean ground water, grey water, effluent or sewage.

CLEAN/GROUND WATER PUMPS

NEWTON NP150 (P1)Medium head and low to medium duty pump. The NP150 is an automatic pump, with integral vertical float switch and so is not suitable for use with our pump control panels. It can be used with Newton Power Converters of 1200W or over to give continual pumping even when the power is out.

The NP150 is supplied with a one way check valve and is suitable for 40mm or 50mm discharge pipe. The pump is sold as pump only, or as a key component in our Newton Titan and Newton Titan-Pro packaged pump systems.

3 year manufacturers warranty.

NEWTON NP400 (P2 & P3)Available in both manual (P3) and automatic (P2) versions, the NP400 is the most popular high performance submersible pump in our portfolio. The NP400 has a unique vertical float mechanism which can be adjusted to suit each individual pumping assignment. It can be used with Newton Power Converters of 1200W or over to give continual pumping even when the power is out.

The NP400 is supplied with a one way check valve and is suitable for 40mm or 50mm discharge pipe. The pump is sold as pump only, or as a key component in our Newton Titan and Newton Titan-Pro packaged pump systems.




Page 26





NEWTON NP750 (P5 & P6)The Newton NP750 is a high head and high performance pump. The NP750 is available as an automatic pump (P5), or as a manual pump (P6) for use with our pump control systems. It can be used with Newton Power Converters of 3000W to give continual pumping even when the power is out.

For increased duty in a twin pump system, separate discharge lines should be used. The NP750 is sold as pump only, or as a key component in our Newton Titan-Pro packaged pump system.


EFFLUENT PUMPS (NOT SEWAGE)

NEWTON NP400W (P4)The Newton NP400W is a medium head and medium performance pump specifically placed within the Newton pumping range for when dishwasher, washing machine or bath / shower waste is to be removed from the sump. It is an automatic pump with a specially designed adjustable float arrangement that cannot be fouled by hardened soaps etc. It can be used with Newton Power Converters of 1200W or over to give continual pumping even when the power is out.


NEWTON NP750W (P8)The Newton NP750W is a high head and high performance effluent pump for the removal of waste water from the Newton Titan-Pro sump chambers or formed concrete chambers.

The NP750W is an automatic pump with a specially designed adjustable float arrangement that cannot be fouled by hardened soaps, effluent and grease etc. It can be used with Newton Power Converters of 3000W to give continual pumping even when the power is out.


SEWAGE PUMPS

NEWTON 750 TROJAN (VORTEX) (P9)The Newton 750 Trojan is a low head and high performance sewage pump for the removal of sewage, effluent, waste water and ground water with suspended soft solids of up to 50mm.

The Newton 750 Trojan is primarily used as the standard pump in our Trojan sump systems but can also be used as a stand-alone pump within formed concrete sumps.



Page 27





NEWTON FLYGT DXG (GRINDER) (P14 & P16)The Newton Flygt DXG (Grinder) is high performance submersible grinder pump which cuts solids in sewage into smaller bits that can easily pass through the impeller and discharge pipes.

The Newton Flygt DXG residential grinder effectively delivers domestic sewage and waste water from the Newton Trojan System to sewer mains.

Available in Automatic (P14) or Manual (P16) versions.

SPECIALIST PUMPS

NP 400LLPS (SP1)The Newton NP400 LLPS is a pumping system based around the Newton NP400PP Puddle Pump. Switching of puddle pumps is problematic because by their nature they are dealing with low heights of water. This makes conventional switching difficult.

The NP400 LLPS has a small control panel and low level switching module added to the NP400PP Puddle Pump that will give accurate and safe switching of water levels of just 10mm.

The NP400 LLPS will pump down to just 1mm of water depth. The NP400 LLPS can also be supplied as a stand alone manual pump if required.


SEWAGE LIFTING STATION

TROJAN SEWAGE PUMPING SYSTEM (TR1-TR12)Newton Trojan systems are specialist packed sewage systems based upon a 610mm diameter sump with depth options of 1000mm and 1500mm.

The Trojan systems are supplied with either single or twin pump systems using the Newton 750 Trojan (Vortex) or Newton Flygt DXG (Grinder).

Includes a 110mm wall flange and hole cutting kit to suit.

Note: The Trojan System is not supplied with a High Water Level Alarm.



Page 28





CLEAN/GROUND/EFFLUENT PUMPING SYSTEMS

TITAN-PRO WHITE (TPW)The Newton Titan-Pro White is designed specifically to be used with Newton System 500. The adjustable neck allows for the sump to be installed at a fixed height relative to the slab so that the connection in from the Newton drainage system and the pump discharge line are made above the concrete.

The sump can be used with single pumps, twin pumps and twin pumps with twin discharge lines for greater pump efficiency.

The Titan-Pro White is available with the following pumps: NP150, NP400, NP400W, NP750, NP750W.

Titan Pro White is supplied with a 450mm x 450mm recessed manhole cover as standard.

Chamber dimensions: 805mm high x 650 wide

TITAN-PRO GREEN (TPG)The Titan-Pro Green is designed for the pumping of ground water or surface water where the added features of the Titan-Pro White are not required. Ideally suited for receiving connections form rainwater gullies. A hole cutter and 1 x 110mm wall flange is supplied allowing for accurate on-site postponing of the invert connection.

The sump can be used with single pumps or twin pumps with a single discharge line.

The Titan-Pro Green is available with the following pumps: NP150, NP400, NP400W, NP750, NP750W.

Titan Pro Green is supplied as standard with a 450mm x 450mm recessed manhole cover as standard.

Chamber dimensions: 805mm high x 650 wide

NEWTON TITAN NP150 (T1 & T3)The Titan NP150 is a complete pumping solution for when a smaller chamber than the Titan-Pro is required and is suitable for low volume pumping situations within basements or for the pumping of collected surface water from light wells etc.

The Titan NP150 system comprises a sump chamber & lid, Newton NP150 Pump, one-way and shut-off valves and the Newton PA12 High Water Alarm.

For twin NP150 pumps our purchase code T3 applies.

Chamber Dimensions: 615mm high x 535 wide



Page 29





PUMPING ANCILLARY PRODUCTS

NEWTON CONTROL PANEL PRO (CP2)The Newton Control Panel Pro is a class-leading pump control panel with many unique features which has been designed by Newtons to provide the ultimate in pump operation and diagnostic capabilities. The panel interfaces with Newton Power Converters and telemetry systems and can be connected to the house monitoring systems. The Control Panel PCB is split with two separate circuits, ensuring that pumping will continue even if one of the control circuits should fail. This effectively means that Newton Control Panel Pro is two control panels in one case, offering unrivalled protection.

NEWTON HIGH WATER LEVEL ALARM (PA12)The Newton High Level Water Alarm has been designed to detect high water levels within pump sump chambers and is included within the Newton Titan-Pro and Newton Titan pumping systems. The Alarm is powered by a standard 9V battery. It can be programmed to automatic reset or manual reset after an alarm occurrence. A mute button to the front face silences the alarm once the alarm condition is discovered. The red flashing alarm light gives visual indication of an alarm condition and this light will continue to show even when the alarm sounder is muted.

NEWTON 1200w POWER CONVERTER (C1 & C3)Battery back up facilities for pumps of 150W and 400W is provided by the Newton 1200W Power Converter - C1. The unit receives 12V power from a deep cycle leisure battery and converts this into 230V mains power to ensure that the Newton Pump continues to operate even during a power outage. A two phase charger ensures that the battery is fully charged at all times by trickle charging to keep the battery at optimal charge and then by boosting up to 20 Amps to quickly re-charge the battery after extended use.

Purchase Code C1 is for the Power Converter only. Purchase code C3 includes a 115A/H deep cycle leisure battery, a secure battery box, and the power leads for connection to the mains and the battery.

NEWTON 3000w POWER CONVERTER (C2 & C4)The Newton 3000w Power Converter - C2 receives 12V power from a deep cycle leisure battery and converts this into 230V mains power to ensure that the Newton Pump continues to operate even during a power outage. A two phase charger ensures that the battery is fully charged at all times by trickle charging to keep the battery at optimal charge, and then by boosting up to 20 Amps to quickly re-charge the battery after extended use. This 3000W unit is designed to be used with single Newton pumps with power outputs of up to 750W only or with dual pumps of 400W to 750W when switched by one of our Control Panels.

Purchase Code C2 is for the Power Converter only. Purchase code C4 includes a 115A/H deep cycle leisure battery, a secure battery box, and the power leads for connection to the mains and the battery.



Page 30



NEWTON MULTI-USE Multi-Use Products


NEWTON MULTI-USESystem Overview

The Multi-Use section is home to products that are used within more than one of our systems. Waterseal Tape, for example, can be used with System 300, System 400, System 500, System 600 and System 800.

Highlights include Newton Mesh Tape, which is used with all of our meshed membranes to facilitate direct plastering or rendering, and the Newton MultiPlug which includes a soft rubber sealing grommet and a pin, which when inserted into the plug, expands the fixing to provide a better fit within soft or friable substrate.

NEWTON MESH TAPE (A25)Newton Mesh Tape is a self-adhesive sealing tape made of a butyl rubber compound with a polypropylene fleece finish. The tape has been developed for use with Newton Meshed Membranes where a surface ‘key’ is required for plastering or rendering over.

Newton Mesh Tape is the recommended jointing tape for the following Newton membranes: Newton 603 Mesh, Newton 603 Bonded Tile, Newton 803 Newtonite, Newton 805 Newlath. It can also be used as an overtape to provide a key above joints to Newton System 500 meshed waterproofing membranes (Newton 503 Mesh and Newton 508 Mesh), over joints already sealed with Newton WaterSeal Tape, Newton WaterSeal Rope or Newton Overtape.

Newton Mesh Tape is available in 150mm x 10m rolls.

NEWTON OVERTAPE (A7, A8, A9)Newton Overtape is used to create single sided taped joints as an overtape to seal adjacent butted and overlapped membranes, or to seal above joins to the membrane created whilst shaping the membrane to fit convoluted substrate.

Newton Overtape can also be used for the sealing of protrusions through the membrane.

Newton Overtape is available in rolls 150mm x 20m (A7-Black), 100mm x 20m (A8-Black, A9-White)

NEWTON WATERSEAL ROPE (A6, A6W)Newton WaterSeal Rope is used to form a seal at the overlap of adjacent sheets of Newton membranes when neither a flange joint or stud into stud joint has been made. A bead of WaterSeal Rope is used for the sealing of penetrations through the Newton membranes.

WaterSeal Rope is also used to create a sealing ring to the base of the Newton NuSeal Plug.

WaterSeal Rope is supplied in rolls 10mm x 4.75m and is available in Black (A6) or White (A6W)



Page 31


J o h n N e w t o n L t d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o . u k© John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217


NEWTON MULTI-USE Multi-Use Products


NEWTON WATERSEAL TAPE (A5, A5W)Newton WaterSeal Tape is used to form a seal at the overlap of adjacent sheets of Newton membranes.

WaterSeal tape is placed between the flange of one sheet and the top flat surface of the next, or if the studs interlock, it can be used to seal between the flat contact area of this type of joint.

WaterSeal tape is supplied in rolls 30mm x 2mm x 22.5m in Black (A5) and White (A5W)

NEWTON MULTIPLUG (A1)Newton MultiPlug has been engineered to give a better fix in questionable substrates. It has the added benefit of having a rubber sealing grommet supplied with the plug. In very poor substrate, a pin (supplied in bags of 100 at extra cost) is inserted into the plug that expands its outer circumference by nearly 2mm to tighten the plug into the substrate.

The Newton MultiPlug is pre-drilled to accept a size 10 (5mm) self-tapping screw for the fixing of battens or other dry-lining systems. Newton MultiPlugs are recommended in all below ground membrane applications except vaulted arches.

Newton MultiPlugs are supplied in bags of 100 (A1)

NEWTON NUSEAL PLUGS (A2, A3)Newton NuSeal Plugs are used to secure Newton System 500 membranes to building substrate and to fix battens or tracking systems. Prior to using NuSeal plugs, wrap a bead of Newton WaterSeal Rope around the head of the plug to form a compression seal.

NuSeal Plugs are recommended when applying Newton 508 or Newton 508 Mesh to vaulted arches. Note: 11mm SDS drill bit required, plugs are 70mm in length.

Newton NuSeal Plugs are supplied in bags of 100 in Red (A2) or White (A3)

For further information or free technical advice please ring 020 7237 1217 or visit www.newton-membranes.co.uk

Page 32


NEWTON WATERPROOFING SYSTEMS

Innovators In Structural Waterproofing And Damp Proofing Products For Over 160 Years

John Newton & Co Ltd, Est 1848, is the UK’s leading independent supplier of structural waterproofing systems, water control and drainage products. Newtons offer the best available, BBA certificated solutions for waterproofing and damp proofing applications in new-build and refurbishment projects. Our range of structural waterproofing systems, including cementitious products, deck and roofing membranes and liquid applied floor coatings enable us to offer full waterproofing solutions for a wide variety of projects.

Newton Waterproofing Systems control and remove unwanted water from leaking tunnels and underpasses, railway arches, wet basements, flooded cellars and damp vaults to make warm habitable areas or areas suitable for dry storage in both commercial and domestic projects.

Newton structural waterproofing and damp proofing products offer the highest level of protection. Our team of technical experts can design and modify technical drawings in all formats and design a waterproofing solution best suited to your requirements. In addition, Newtons nationwide network of Newton Specialist Basement Contractors (NSBC) can offer a fully guaranteed design and installation of our systems.

John Newton & Company Ltd.12 Verney Road, London SE16 3DH

Phone: 020 7237 1217 www.newton-membranes.co.uk [email protected]

newton waterproofing systems - poulton remedial … · newton waterproofing systems ... lime...

Documents